DAviT ARM - Fall Prevention, Fall Protection & Fall Arrest...

For any technical queries please call our advice line on 0845 241 9102

ReviSiOn nO: 001 PRODUcT DATA SheeT RePORT nO: 024

PRODUcT cODe: DA300

DAviT ARM

024


PROdUcT dEScRIPTION:The Aviator Davit Arm is designed to be removable and to be used together with the permanent Davit base plates. They are designed for lifting and lowering personnel and materials. The hook on the end of the arm allows abseil and lifting ropes to extend over the roof edge or balustrading. The Davit base can also be used to anchor a personal fall arrest system when the user is being lifted and lowered. It is essential when designing rope access to ensure at least 2 abseil rope connection points (one for working line and the other for safety line) are available to connect to at any one time. Davit arms are manufactured in aluminium section to ensure they are light weight and easily transportable. The davit arm is designed to fold to facilitate storage and transport.

The Standard DA300 davit arm can be manufactured up to a height of 1500mm with a maximum reach of 850mm. It weighs approximately 15Kg. The arm can be locked into 2 positions – 135 degrees and 90 degrees off the vertical arm. The locking pin and clip are permanently fixed to the Davit arm to prevent them being mislaid.

AviATOR DAviT ARM

In use

Folded not in use

Removable

1.25m

0.8m

024


The DA300 davit arm has a maximum safe working load of 136kg. This is a greater than 10:1 safety factor for personnel use and a greater than 5:1 safety factor for materials (272Kg). In the event of an emergency or for rescue situations 2 persons can use the davit arm. The davit arm can be supplied with a hand winch and pulley for material lifting. The Aviator davit arms are designed and manufactured to fit into the Aviator davit base plates. Never use the Aviator arm on any other make or model of davit base or the system warranty will be invalidated.

AviATOR DAviT ARM

900

1350

SWL136Kg

For personnel

SWL272Kg

For materials

only

Pulley

Handwinch

024


Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035;

S < 0.040; Mo 0.4 – 0.6.

Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C

Density 7.87 g/cm3 at 20 °C

Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range

I-F Steel: 12.9 μm/m/°C in 20 °C to 100 °C range

Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel: 93 W/m°C

at 20°C

Specific Heat 481 J/kg/°C in 50 °C to 100 °C range

Electrical Resistivity 0.142 μΩ•m at 20 °C

davit armAluminium 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength 186MPa Yield strength 110MPa

component parts and fixingsStainless Steel - Grade 304 (UNS S30400)Fe, <0.08% C, 17.5-20% Cr, 8-11% Ni, <2% Mn, <1% Si, <0.045% P, <0.03% Stainless Steel

brackets - galvanised steel

MATERIAL SPEcIFIcATION:

Galvanised hand winch

Folding joint

Stainless steel rope guides

Stainless steel fixings

Aluminium arm

Aluminium locating spiggot

AviATOR DAviT ARM

024


OPERATING ANd dESIGN STANdARdS:Eurocodes are designated by EN

British standards are designated by BS

• Steel – EN10 113 and EN 10 025• BS 7985: 2013 Code of Practice for

Rope Access Methods• The lifting operations and lifting equipment

regulations 1998• LOLER REG. 5(1) (a and b) for design• LOLER REG. 7(a, d and e) for marking• LOLER REG. 9 (1, 2 , 3 a and b) for examination• ISO 9001:2008, ISO14001:2004, BS OHSAS

18001:2007• Management of health and safety at work

regulations 1999 (MHSWR) ref.2• Work at height regulations 2005 (Ref 7)• Work at height (amended) regulations 2007

(Ref. 8) WAHR

• Provision and use of work equipment regulations 1999 PUWER 98 (Ref.5)

• The work at height safety association WAHSA- guidance on inspecting eyebolts for personal fall protection purposes

✔

BS ENISO

Standards

Typical connection loads (Maximum SWL 136kg for single user with a factor of safety greater than 10:1 with maximum davit arm cantilever of 0.8m)

9948ISO 9001:2008

9948ISO 14001:2004

9948BS OHSAS 18001:2007

AviATOR DAviT ARM

Ultimate factored load on bracket base

Bracket moment

Tension

6.28kN/m 21.3kN

5.02kN

Note: For guidelines only to be checked by Chief Engineer.

024

The company operates to the following standards


TRAINING REQUIREMENTS:All personnel who use the Aviator system must be trained to IRATA level 3 standard or work directly under a supervisor who holds this certificate.

All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course.

Courses are available from Sayfa Systems UK Ltd.

INSPEcTION/MAINTENANcE/TRAINING

INSPEcTION ROUTINE:All systems to be inspected at least every 6 months from date of installation.

In harsh environments all systems to be inspected at least every 3 months.

Inspections must be carried out by approved Aviator engineers. All inspections must be carried out in accordance with BS7985:2013 , LOLER REG.9 (1,2,3 a and b) and IRATA international guidelines.

Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.

Contact Sayfa Systems to arrange inspections.

MAINTENANcE SchEdULE: MANUFAcTURERS REQUIREMENTAll maintenance to be carried out by approved Aviator engineers. Maintenance to be in accordance with Sayfa Systems Uk (manufacturer) guidelines and recommendations.

Maintenance to be in accordance with SIMS standards. (details available on request).

Maintenance to be carried out at time of product inspection. In harsh environments all systems to be maintained at least every 3 months together with yearly inspection.

Contact Sayfa Systems to arrange system maintenance.

6 Months

From date of installation

NASLOT

cERTIFIEd

3Months

in harsh environments

d

Sa

yfa

SyStem

S

Ce

R t I f I C a

te

NASLOT

cERTIFIEd

Certificate

PASS ✔

3Months

in harsh environments

d

6 Months

From date of installation

AviATOR DAviT ARM

024


AviATOR DAviT ARM

cOMPONENT PART dETAILS:davit arm personnel use dA300 bIM No: SpecEquip_RfSftySymdvtArm_SayfaSystems_dA300_M3_G2

davit arm materials lifting dA400 bIM No: SpecEquip_RfSftySymdvtArm_SayfaSystems_dA400_M3_G2

Winch bracket dAWb01bIM No: SpecEquip_RfSftySymdvtArmWnchbkt_SayfaSystems_dAWb01_M3_G2

024

Portable

Folded

135 Degrees

90 Degrees

R T

1

1

2

2

3

3

4

4

5

5

6

6

A A

B B

C C

D D

Folding Davit Arm

DA300

Mark.S MW 10/06/2015

B

Designed by Checked by Approved by Date

1 / 4 Edition Sheet

Date

DA300Single User Folding Aluminium

Davit Arm

Portable

Folded

135 Degrees

90 Degrees

R T

1

1

2

2

3

3

4

4

5

5

6

6

A A

B B

C C

D D

Folding Davit Arm

DA300

Mark.S MW 10/06/2015

B


1 / 4 Edition Sheet

Date


Davit Arm

Portable

Folded

135 Degrees

90 Degrees

R T

1

1

2

2

3

3

4

4

5

5

6

6

A A

B B

C C

D D

Folding Davit Arm

DA300

Mark.S MW 10/06/2015

B


1 / 4 Edition Sheet

Date


Davit Arm

135 Degrees

Portable

90 Degrees

Folded

1

1

2

2

3

3

4

4

5

5

6

6

A A

B B

C C

D D

Folding Davit Arm

DA400

Mark.S MW 10/06/2015

C


1 / 7 Edition Sheet

Date

DA400Material Lifting Folding Aluminium

Davit Arm

135 Degrees

Portable

90 Degrees

Folded

1

1

2

2

3

3

4

4

5

5

6

6

A A

B B

C C

D D

Folding Davit Arm

DA400

Mark.S MW 10/06/2015

C


1 / 7 Edition Sheet

Date


Davit Arm

135 Degrees

Portable

90 Degrees

Folded

1

1

2

2

3

3

4

4

5

5

6

6

A A

B B

C C

D D

Folding Davit Arm

DA400

Mark.S MW 10/06/2015

C


1 / 7 Edition Sheet

Date


Davit Arm

135 Degrees

Portable

90 Degrees

Folded

1

1

2

2

3

3

4

4

5

5

6

6

A A

B B

C C

D D

Folding Davit Arm

DA400

Mark.S MW 10/06/2015

C


1 / 7 Edition Sheet

Date


Davit Arm


FIxING dETAILS: davit arm for personnel use bIM No: SpecEquip_RfSftySymdvtArm_SayfaSystems_dA300_M3_G2

AviATOR DAviT ARM

ARM HINGETO HOLD ARM AT 90°AND 135° ONLY

ALUMINUM FOLDING ARMWEIGHT 15kg Approx

MOUNTING HOLESTO SECURE DAVIT ARMTO DAVIT BASE WITH 4M16 BOLTS

800-

1500

150-

350

955

650-850

Client:

Contract:

Project Title:

· Line to be located as indicated on theroof plan.

· Line primarily used to gain access toexposed roof edges.

· Incorporates Aviator™ units and allSayfa Systemscomponents required.

· Fixing details for Aviator™ units asindicated within layout.

· System to be used in conjunction with2m restraining lanyard unless statedotherwise.

· Enables two users simultaneously atany one time.

System Details

SAYFA SYSTEMS

FIXING DETAIL

AVIATOR™DAVIT ARM SYSTEMFOR PERSONAL USE

Revision:

Drawn By: MW

Scale:

Date:

Checked By:

Job No:

DWG No:

Jubilee House

ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com

Unit 3, Gelders Hall Road

Status:

UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.

A = Access point

Drawing Symbols

THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©

DRAWING REVISIONSREV DATE COMMENT

THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________

DRAWING NO. ______________

TYPICAL FIXING DETAILS

22/12/2014

As Dimensioned

For DesignN/A

N/A

001

DJ

024


FIxING dETAILS: davit arm for materials lifting bIM No: SpecEquip_RfSftySymdvtArm_SayfaSystems_dA400_M3_G2

AviATOR DAviT ARM

MOUNTING HOLESTO SECURE DAVIT ARMTO DAVIT BASE WITH 4M16 BOLTS

ALUMINUM FOLDING ARMWEIGHT 35kg Approximately

150-

350

800-

1500

650-850

Client:

Contract:

Project Title:

· Line to be located as indicated on theroof plan.

· Line primarily used to gain access toexposed roof edges.

· Incorporates Aviator™ units and allSayfa Systemscomponents required.

· Fixing details for Aviator™ units asindicated within layout.

· System to be used in conjunction with2m restraining lanyard unless statedotherwise.

· Enables two users simultaneously atany one time.

System Details

SAYFA SYSTEMS

FIXING DETAIL

AVIATOR™DAVIT ARM SYSTEMFOR MATERIALSLIFTING

Revision:

Drawn By: MW

Scale:

Date:

Checked By:

Job No:

DWG No:

Jubilee House

ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com

Unit 3, Gelders Hall Road

Status:

UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.

A = Access point

Drawing Symbols

THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©

DRAWING REVISIONSREV DATE COMMENT

THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________

DRAWING NO. ______________

TYPICAL FIXING DETAILS

22/12/2014

As Dimensioned

For DesignN/A

N/A

001

DJ

024

Sayfa Systems UK Ltd (“SSUK”) warrants to the original purchaser (the “Customer”) that, subject to these provisions, its ManAnchor Safety Systems(the “Product”) will be free of material defects in workmanship and materials under normal use, for a period of up to twelve months from the date of delivery (the “Warranty Period”). Warranties can be extended up to 25 years at the discretion of Sayfa Systems UK Ltd and will be renewed each year following the completion of the legal recertification by an authorised installer.

This Warranty shall only become valid and effective once registered with SSUK using the attached form. The warranty number provided upon registration must be produced when any claim is made under the Warranty. When this Warranty is registered by the Customer, it shall supersede and replace any warranties given by SSUK in its standard terms of sale.

Before returning the Product believed to be defective SSUK must be supplied with details of the warranty number provided upon registration and a description of the defect which has arisen.

To report a defective Product covered by this Warranty please contact Sayfa Systems UK on 0845 2419102.

During the Warranty Period, if any part of the Product is found in the reasonable judgement of SSUK to contain material defects in materials or workmanship, SSUK will, at its option:

1 provide replacement parts necessary to repair the Product;

2 replace the Product with a comparable product; or

3 re-fund the amount paid for the Product, less depreciation, upon its return.

Replacement parts or products will be new or serviceably used, comparable in function and performance to the original part or Product and warranted for the unexpired part of the Warranty Period. Any additional purchases or upgrades will not extend this Warranty. Sayfa Systems will not be liable for any on costs, remedial work charges or supply of temporary access and handrail, when supplying replacement parts.

This Warranty covers normal use only. SSUK shall not be liable for a breach of this Warranty:

1 if the Customer makes any further use of the Product after notifying SSUK of a defect;

2 to the extent that any defect arises out of normal wear and tear;

3 to the extent that any defect arises out of actions or event beyond the control of SSUK, including without limitation, impacts, fire, flood, wind, earthquake, lightning or similar disaster, war, lockout, epidemic, destruction of production facilities, riot, insurrection, or material unavailability; unauthorised modifications, attachments or peripherals;

4 to the extent that any defect arises as a result of the Customer’s failure to follow SSUK’s written or oral instructions as to the storage, installation, commissioning, use and yearly maintenance checks of the Goods or (if there are none) good trade practice.

5 To the extent that the Customer has engaged the services of any unauthorised company to install, maintain, retest or do any works on the SSUK systems without written authorisation from SSUK.

SAyfA SySTeMS UK LTD PRODUcT WARRAnTy

This Warranty shall be governed by and construed in accordance with the laws of England and Wales and SSUK and the Customer each agree that any disputes relating to this Warranty shall be subject to the exclusive jurisdiction of the courts of England and Wales.

Neither SSUK nor the Customer intend that any term of this Warranty shall be enforceable by virtue of the Contracts (Rights of third Parties) Act by any person who is not a party to it.

This Warranty is personal to the Customer and may not be assigned or otherwise transferred to any other person.

Except for the warranties expressed in this agreement, ssuk disclaims all other warranties, either express or implied, including implied warranties of merchantability or fitness for a particular purpose, other than those warranties implied by and incapable of exclusion, restriction or modification by law. The maximum liability of ssuk to you is limited to the purchase price paid for the product. Ssuk will not be liable under this warranty for property damage, death or personal injury (except where caused as a result of the negligence of ssuk), loss of use, interruption of business, “down time”, loss of use of related equipment, lost profits, lost data or other consequential, incidental, punitive or special damages, however caused, whether for breach of warranty, contract, tort (including negligence), absolute or strict liability or otherwise. Nothing in this warranty shall have the effect of excluding or limiting any liability of ssuk which cannot be excluded or limited by law.

q Handrail Systemsq Balustrade Systemsq Walkway Systems

To register your product Warranty under the terms of Sayfa Systems UK Ltd Product Warranty please complete the form below and send to:

SAYFA SYSTEMS UK LTDJubilee House, Unit 3, Gelders Hall Road, Loughborough, Leicestershire LE12 9NH

Section 1 – to be completed by customer. failure to supply this information will invalidate the warranty.

Company NameContact NameProperty Address

Type of product installed: q Safety Line Systemsq Access Ladders

Delivery/ Installation DateCorrespondence Address

Tel Email address

Signature

Section 2 – to be completed by Sayfa Systems UK Ltd before warranty can be effective.

Warranty No*

Date*

Signature*

* To be completed by Sayfa Systems UK Ltd

DAviT ARM - Fall Prevention, Fall Protection & Fall Arrest...

Documents

Transcript of DAviT ARM - Fall Prevention, Fall Protection & Fall Arrest...