CV Vacuum Venturi - Air &...

Tel: 1.866.280.3766 | Fax: 1.866.280.4829 | www.vacuforce.com

CV Vacuum Venturi

Venturi Model

Supply Pressure

Air Consumption

Evacuation time to different vacuum levels in sec/ft³

3”Hg 6”Hg 9”Hg 12”Hg 15”Hg 18”Hg 21”Hg 24”Hg 27”HgCV05H 70psi 0.46 24.3 57.3 101 160 231 305 433 597 - CV10H 70psi 1.55 5 10 16 25 36 51 77 118 226 CV15H 70psi 3.53 2.5 5 7 11 16 22 32 47 112 CV20H 70psi 6.36 1.7 3 6 5.5 9 13 19 27 61

Venturi Model

Supply Pressure

Vacuum flow at different vacuum levels in “Hg

0”Hg 3”Hg 6”Hg 9”Hg 12”Hg 15”Hg 18”Hg 21”Hg 24”Hg 27”HgCV05H 70psi 0.21 0.19 0.17 0.15 0.13 0.11 0.09 0.07 0.05 0.03 CV10H 70psi 0.95 0.85 0.75 0.65 0.55 0.45 0.35 0.25 0.15 0.05 CV15H 70psi 2.22 1.98 1.74 1.5 1.26 1.01 0.76 0.51 0.26 0.1 CV20H 70psi 3.88 3.45 3.02 2.59 2.16 1.73 1.3 0.87 0.44 0.25

Venturi Model Silencer Model The –SK and –S models which have an integral vacuum switch include a silencer as standard. The non switch models as shown on the right are supplied WITHOUT a silencer and therefore if they are required, should be ordered separately.

CV05H PSU-01 CV10H PSU-01 CV15H PSU-02 CV20H PSU-03

Features: • Anodized Aluminum Body • Maximum Vacuum of 27”Hg • Vacuum Flow rates up to 4CFM • Single Stage Technology

No Moving or Wearing Parts

Click HERE for List Pricing and Stock

Page 2 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.VENTURI&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


CV Vacuum Venturi

Dimensions CV..HSK Venturi

CV05H and CV10H

CV15H

CV20H

Dimensions CV..H Venturi


Page 3 of 53



CV Vacuum Venturi

CV05HSK and CV10HSK

CV20HSK

CV15HSK


Page 4 of 53



V Series Venturi

Features: • Lightweight Delrin Plastic Construction • Maximum Vacuum of 27”Hg • Vacuum Flow rates up to 4CFM • Single Stage Technology • No Moving or Wearing Parts

Performance Tables These performance tables offer details of the vacuum flow performance based on the venturi model and orifice size.


Page 5 of 53



V Series Venturi

Model - VML

VML05 Performance Table VML10 Performance Table

Model Number Tube Connection

Dimension L Dimension P Max Vacuum Air Consumption Vacuum Flow

VML0504 5/32 60 14.3 27.3”Hg 0.6CFM 0.28CFM VML0506N 1/4 66 14.3 27.3”Hg 0.6CFM 0.28CFM VML1006N 1/4 76 15.8 27.3”Hg 2.3CFM 1.1CFM VML1008 5/16 79 15.8 27.3”Hg 2.3CFM 1.1CFM


Page 6 of 53



V Series Venturi

Model - VMK

Model - VMT

Model Number Tube Connection

Thread Size Dimension L Dimension P Max Vacuum

Air Consumption

Vacuum Flow

VMK054M5 5/32 10-32UNF 56 14 27.3”Hg 0.6CFM 0.28CFM VMK100801 5/16 1/8BSPT 75 16 27.3”Hg 2.3CFM 1.1 CFM

VMK05 Performance Table VMK10 Performance Table


Page 7 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=VENTURI.VMK&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


V Series Venturi

Model - VMT

Model - VAB Style

VMT05 Performance Table VMT10 Performance Table

Model Number Tube L E1 E2 F2 Max Vacuum

Air Consumption

Vacuum Flow

VMT0504 5/32 60 24 29 15 27.3”Hg 0.6CFM 0.28CFM VMT0506N 1/4 60 24 32 15 27.3”Hg 0.6CFM 0.28CFM VMT1006N 1/4 76 27 40 15 27.3”Hg 2.3CFM 1.1CFM VMT1008 5/16 79 27 42 15 27.3”Hg 2.3CFM 1.1CFM


Page 8 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=VENTURI.VMT&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


V Series Venturi

Model - VAB

Model Number Tube Max Vacuum

Air Consumption

Vacuum Flow

VAB0704 5/32 27.3”Hg 1.25CFM 0.5CFM VAB0706N 1/4 27.3”Hg 1.25CFM 0.5CFM VAB1204 5/32 28.0”Hg 3.15CFM 1.4CFM VAB1206N 1/4 28.0”Hg 3.15CFM 1.4CFM

VAB07 Performance Table VAB12 Performance Table


Page 9 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=VENTURI.VAB&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


V Series Venturi

Model - VABS

Model Number Tube Max Vacuum

Air Consumption

Vacuum Flow

VABS0704 5/32 27.3”Hg 1.25CFM 0.5CFM VABS1204 5/32 28.0”Hg 3.15CFM 1.4CFM

VABS07 Performance Table VABS12 Performance Table

The VABS series of vacuum venturi utilizes the VAS Vacuforce switch and therefore provides a very compact ejector with a part presence feature. Ideal for small pick and place applications where the user must know of the part being handled is located on the vacuum cup.


Page 10 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=VENTURI.VABS&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


V Series Venturi

Model - VMB

Model Number Tube Thread L E Max Vacuum Air Consumption Vacuum Flow VMB070801 5/16 1/8BSPT 60 28 27.3”Hg 0.6CFM 0.28CFM VMB100801 5/16 1/8BSPT 60 28 27.3”Hg 0.6CFM 0.28CFM

VMB10 Performance Table VMB07 Performance Table

The VMB series allows connection of multiple units directly to a compressed air manifold to feed different vacuum points or can be mounted directly onto the A port of a 3-way compressed air valve. The exhaust port is a push to connect fitting so this ejector is ideal for a clean room environment where the product being handled is sensitive to exhaust gases from the venturi.


Page 11 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=VENTURI.VMB&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


V Series Venturi

Model - VMD

Model Number Tube Thread L E Max Vacuum Air Consumption Vacuum Flow VMD070801 5/16 1/8BSPT 49 28 27.3”Hg 0.6CFM 0.28CFM VMD100801 5/16 1/8BSPT 49 28 27.3”Hg 0.6CFM 0.28CFM

VMD10 Performance Table VMD07 Performance Table

The VMD series is very similar to the VMB model but has an integral exhaust feature. The VMD allows connection of multiple units directly to a compressed air manifold to feed different vacuum points or can be mounted directly onto the A port of a 3-way compressed air valve.


Page 12 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=VENTURI.VMD&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


Mini Style Venturi

Features: • Maximum Vacuum Level 25.5”Hg • Maximum Flow Rate 7.7CFM • Optimum Supply Pressure 75psi(g) • Noise Level


Mini Style Venturi

Dimensions (mm)

Model L1 ABM5-NB 20

ABM10-NB 20 ABM20-NB 28 ABM30-NB 35


Page 14 of 53


Classic Style Venturi

Features: • Maximum Vacuum Level 27”Hg • Maximum Flow Rate 38CFM • Supply Pressure 45 – 87psi(g) • Noise Level


Classic Style Venturi

Standard Model Air Saving Model (AS)

Dimensions (mm)

Model L1 L2 VTM25L 45.5 203.5 VTM50L 45.5 203.5 VTM100L 65 223


Page 16 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.VENTURI.CLASSIC&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


Material Conveyors

ØA ØB ØC L VFMC13 13 25 45 140 VFMC19 19 32 54 190

Features: • Lightweight Aluminum Construction • Hard Anodized Finish – Resistant to abrasion • No Moving Parts • No Heat Generation • Maintenance Free • Operates at pressures up to 100psi(g)

Suitable for conveying:

• Powder material • Granular material • Machining swarf, chips • Fumes • Wood chips • Small parts • etc


Page 17 of 53



Vacuum Switch

The VAS vacuum switch is a simple mechanical indicator of vacuum level achievement. Fully adjustable and with a simple push to connect fitting for vacuum connection the VAS switch is ideal for most part presence applications.

Model VAS04 VAS06N Minimum Set Value 12.0”Hg Accuracy 1.5”Hg Hysteresis 3”Hg Electrical Rating AC125V – 5A Vacuum Connection 5/32” 1/4"


Page 18 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=SWITCHES.EHCVAS&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


Digital Vacuum Switch


Page 19 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.SWITCHES&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


Digital Vacuum Switch


Page 20 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.SWITCHES&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


Self Closing Valve/Velocity Fuse

The Vacuforce self closing valve is used on vacuum cup handling systems where multiple cups are utilizing the same vacuum source. The valve is mounted directly onto the vacuum port of the vacuum cup. If that cup is damaged or does not seals against the load being lifted, the induced vacuum air flow closes the valve shut. This ensures that the vacuum level is retained in the rest of the system vacuum cups. This valve is adjustable and therefore can be used on various size vacuum cups or even on porous surfaces such as cardboard or MDF paneling. The cup mounting can be facilitated using either the G1/4 female of G3/8 male thread. The brass adjustment screw, depending on the cup fitting design can be adjusted with the vacuum cup installed. The image on the lower left shows the simple construction of this valve consisting of:

• Valve Body • Spring • Nitrile Ball • Brass Adjustment Screw

VFSC3/8


Page 21 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=VFSC&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST

Vacuum Valves

Dimensions (mm) Model Number Port Size Exhaust Port Thread Cycle Rate Flow A B C H VF070116 1/4NPT G1/8 10/sec 3SCFM 25 25 44 67 VF070316 1/2NPT G1/8 10/sec 6SCFM 35 35 65 79


Coil Selection (must be ordered separately) Voltage Coil Part Number 24VDC SB486-24VDC 110VAC SB486-110VAC

The Vacuforce direct acting vacuum valves have been developed for use in applications which require a full port vacuum flow without the need for an external air pilot such as is required with spool valves. The direct acting poppet design offers the user a cycle rate of ≥10cycles/sec with a choice of coils for different voltages. Please note that the coil should be ordered separately selecting from the coil table below.

Coil Connector is a DIN43650 Form A type which includes an LED for Power On Indication


Page 22 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.VACUUM.VALVES&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


Vacuum Valves

The JZF series of vacuum valves have been developed to offer the end user a high vacuum flow solution when using larger vacuum pumps or generators. With port sizes of either 1/2NPT or 1NPT, these vacuum valves are far superior in reaction time and cycles per second than traditional actuated ball valve type models normally used in these applications. Manufactured in anodized cast aluminum with Nitrile rubber seals but available with special seal materials on request, the JZF series stands alone in its performance and price bracket for the vacuum user. The two types available are 3VJZF (solenoid actuated with pneumatic pilot) and 3AJZF which is pneumatic pilot only.

Coils for the solenoid valves (3VJZF) should be ordered separately and are available as follows:

Voltage Coil and DIN 24VDC 210DIN24VDC 110VAC 210DIN110VAC

3AJZF – Pneumatic Pilot

3VJZF – Solenoid (external pilot)


Page 23 of 53



Vacuum Valves

Model Number 3VJZF-15EP 3VJZF-25EP Working Medium Air Operation Pilot Assisted, Solenoid Control Orifice 15mm 25mm Port Size 1/2NPT 1NPT Working Pressure 0-27”Hg Body Material Die Cast Aluminum Seal Material Nitrile Rubber Operating Temperature -5ºC to +70ºC Flow Rate 28SCFM 71SCFM Pilot Port 1/8NPT

Dimensions 15EP

Dimensions 25EP


Page 24 of 53



Vacuum Valves

Model Number 3AJZF-15EP 3AJZF-25EP Working Medium Air

Operation Pilot Assisted Orifice 15mm 25mm

Port Size 1/2NPT 1NPT Working Pressure 0-27”Hg

Body Material Die Cast Aluminum Seal Material Nitrile Rubber

Operating Temperature -5ºC to +70ºC Flow Rate 28SCFM 71SCFM Pilot Port 1/8NPT

Dimensions 15EP

Dimensions 25EP


Page 25 of 53



Vacuum Filtration

Vacuforce plastic in-line filters provide easy monitoring, economy and safety. These shatterproof filters are 100% airtight, can withstand high pressures up to 150psi(g) and are designed for use in applications where glass cannot be tolerated. A 10 micron porous plastic element prolongs element life under the most adverse environmental conditions. These filters are typically used on general vacuum applications to prevent impurities from entering the vacuum pump of compressed air venturi inlet. The transparent bowl enables visual inspection of the element condition the quick release bowl offers the user fast element replacement.

• To filter dust and other harmful particles from the vacuum flow • Reduces the risk of breakdown or blockage in the pump • Replaceable porous plastic 10 micron filter element • Available in 1/8” to 1-1/2” NPT or BSP threads

Model Number Description Spare Elements (3 pack)

PVF.125-PE Vacuum Filter 1/8NPT PE25-3 PVF.25-PE Vacuum Filter 1/4NPT PE25-3 PVF.375-PE Vacuum Filter 3/8NPT PE25-3 PVF.5-PE Vacuum Filter 1/2NPT PE75-3 PVF.75-PE Vacuum Filter 3/4NPT PE75-3 PVF1.0-PE Vacuum Filter 1NPT PE10-3 PVF1.5-PE Vacuum Filter 1 1/2NPT PE15-3

Pressure Range 29.5”Hg to 150psi(g)

Materials Of Construction PA (Nylon) Body PC (Polycarbonate) Bowl PE (Polyethylene) Element

Temperature -4ºF to 212ºF (-20ºC to 100ºC) Filtration Efficiency 10µ (0.01mm)


Page 26 of 53


Vacuum Filtration

PVF.125-PE PVF.25-PE PVF.375-PE PVF.5-PE PVF.75-PE PVF1.0-PE PVF1.5-PE Weight (oz) 1.70 1.98 2.47 6.61 6.42 15.0 18.8 Flow ACFM 3 4.2 5.4 31 31 89 180 Volume in³ 2.1 2.4 2.7 11.9 12.5 30.2 41.2 Filter Area (in²) 4.9 4.9 4.9 16.0 16.0 29.5 35.0

PVF.125-PE PVF.25-PE PVF.375-PE PVF.5-PE PVF.75-PE PVF1.0-PE PVF1.5-PE

A 79 79 79 91 91 125 132

B 61 61 61 130 130 163 210

C 51 51 51 112 117 142 175


Page 27 of 53


Vacuum Filtration

Vacuforce heavy duty filters are normally used on more aggressive applications such as centralized vacuum pump or venturi applications where good long life filtration is required. The elements are pleated paper as standard but can also be offered on pleated polyester for damp applications where moisture is present in the air stream. They are also available upon request in stainless steel and activated carbon.


Materials Of Construction Plated Steel (Body) PET (Polyethylene) Element Temperature -4ºF to 212ºF (-20ºC to 100ºC)

Filtration Efficiency >7µ (0.007mm)

F.001 F.002/1 F.002 F.004/1 F.004 F.003 F.005 F.006 Flow Rate ACFM 14 25 25 50 57 63 113 183 Port Size G3/8 G ½ G3/4 G1 G1 ¼ G1 ¼ G 1 ½ G2

F.001 F.002/1 F.002 F.004/1 F.004 F.003 F.005 F.006 Paper Element K.2093 K.2034 K.2034 K2032 K.2032 K.2051 K.2070 K.2050 Polyester Element G3/8 G ½ G3/4 G1 G1 ¼ G1 ¼ G 1 ½ G2


Page 28 of 53


Vacuum Filtration

Dimensions


Page 29 of 53


Vacuum Filtration

OIL BATH FILTERS

The Vacuforce Oil Bath filters are designed to be used in applications where very fine powders or particulates are present in the air stream. Standard vacuum inlet filters will have to have such a fine porosity that the flow would be restricted. The oil bath filters have a small container of oil (ISO20 grade recommended) at the base of the unit. As the air passes through the internal strainer the air passes over the surface of the oil leaving the particulates on the oil surface. Flow rate is not affected by dust being trapped by the oil. Periodic changing of the oil is recommended and the frequency is dependent on the air particulate content.


Materials Of Construction Plated Steel (Body) Stainless Steel Strainer Element Temperature -4ºF to 212ºF (-20ºC to 100ºC)

Filtration Efficiency n/a

FB.001 FB.002 FB.003 FB.004 Flow Rate ACFM 18 53 118 177 Port Size G ½ G1 G1½ G2 A 216 239 305 340 B 73 92 110 140 C 113 105 135 140 ØD 105 132 160 185 E 30 42 60 60 F 100 105 128 142


Page 30 of 53


Vacuum Filtration

Mini Point of Use Filters

These small filters are used in applications requiring filtration at the point of use such as small vacuum cup handling where a small vacuum venturi is the vacuum source and needs protection from dust and debris being pulled back from the work piece.


Materials Of Construction Plastic Temperature 32ºF to 140ºF (0ºC to 60ºC)

Filtration Efficiency >10µ (0.010mm)

Model Connection Tube Ø B F² F ØP Filter Area Weight VFD0706 6mm 58 20 10 19 7.5mm² 25g VFD0706N ¼” 58 20 10 19 7.5mm² 25g VFD1208 5/16” 68 24 14 23 12.5mm² 40g


Page 31 of 53


Single Bellows “B Series” Cups

The Vacuforce VFB series of vacuum cups are designed to offer the vacuum user a simple and effective generic style cup. The cup can be connected to the machinery using the fitting shown on the following page. These cups are available in both Nitrile and Silicone rubber with a 60 and 40 Durometer hardness respectively.

Part Number Matrix Series Size Material VFB 40 N or S

Material Codes N Nitrile Rubber S Silicone Rubber


Page 32 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.VFB&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


Flat “F Series” Cups

The Vacuforce VFF series of vacuum cups are a generic style flat cup. The cup can be connected to the machinery using the fittings shown on the following page. These cups are available in both Nitrile and Silicone rubber with a 60 and 40 Durometer hardness respectively.

Part Number Matrix Series Size Material VFF 40 N or S e.g VFF40N



Page 33 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.VFF&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


Cup Fittings

Fitting Model Fits Cup Model Fitting Model Fits Cup Model

VFB5 VFB30 VFB40 VFF40

VFB10 VFB15 VFF15

VFB50 VFF50

VFB20 VFF20 VFF30

VFB50 VFF50

VFB30 VFB40 VFF40


Page 34 of 53

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.VFB.FITTINGS&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


Cup Fittings

Fitting Model Fits Cup Model

VFB75

VFB110


Page 35 of 53


The Vacuforce PA series of vacuum cups are a generic flat style cup similar in design to the Convum PFG series. The cup can be connected to the machinery using simple fittings, bulkhead assemblies or sprung level compensators. These cups are available in both Nitrile and Silicone rubber with a 60 and 40 Durometer hardness

Part Number Matrix Series Size Material PA 40 N or S


PA Series Flat Cup (Convum PFG Style)


Page 36 of 53


PA Series Flat Cup (Convum PFG Style)


Page 37 of 53


PAK10 Model Number Cup Model ØA B Vacuum Connection

PAK10 PA10 10 34 Ø4mm OD Tube PA15 15 34.5


PAK20 PA20 20 38

Ø6mm OD Tube PA25 25 42 PA30 30 40


PAK40 PA40 40 44 Ø6mm OD Tube PA50 50 45

PA Cup Bulkhead Holders Click HERE for List Pricing and Stock

Page 38 of 53


Model Number Cup Model ØA B C Vacuum

Connection

PAK60 PA60 60 49 19 1/8BSPT PA80 80 51 21

PA Cup Bulkhead Holders


Page 39 of 53


Model Number Cup Model ØA B C Vacuum Connection

PAFS10 PA10 10 69 20 Ø4mm OD Tube PA15 15 66 20


PAFS20

PA20 20 83 30

Ø4mm ID Tube PA30 30 85 30 PA40 40 84 30 PA50 50 85 30

Actual Stroke – 10mm


PA Cup Level Compensators Click HERE for List Pricing and Stock

Page 40 of 53


The Vacuforce PB series of vacuum cups are a generic style single bellows cup similar in style to the Convum, PJG series. The cup can be connected to the machinery using the fittings shown on the following page. These cups are available in both Nitrile and Silicone rubber with a 60 and 40 Durometer hardness respectively.

Part Number Matrix Series Size Material PB 40 N or S


PB Series Bellows Cup (Convum PJG Style)


Page 41 of 53


PB Cup Bulkhead Holders

Model Number Cup Model ØA B Vacuum Connection

PAK10 PB10 10 36 Ø4mm OD Tube PB15 15 38






Page 42 of 53



PAFS10 PB10 10 56 20 Ø4mm OD Tube PB15 15 57 20


PAFS20

PB20 20 69 30

Ø4mm ID Tube PB30 30 75 30 PB40 40 75 30 PB50 50 77 30

PB Cup Level Compensators




Page 43 of 53

USA - 2769 Broadway, Buffalo, New York 14227 | Canada - Suite 174, 14-30 Eglinton Ave W, Mississauga, ON L5R 0C1 Tel: 1.866.280.3766 | Fax: 1.866.280.4829 | www.vacuforce.com

Metal Stamping Cups

The Vacuforce VFFC50 vacuum cup has been developed to handle standard lifting applications such as steel plate handling, wood board, plastic sheets, marble, granite and other flat heavy surfaces. Bonded to a dual threaded fitting this vacuum cup is easily fixed to the machine support. Offered in both Nitrile and Silicone rubber, this generic cup design is very popular in many industries.

Cup Models Rubber Compound Temperature Range Vertical Lifting Force VFFC50-3/8N Nitrile Rubber -40 to 230ºF 34lbs @ 24”Hg VFFC50-3/8S Silicone Rubber -40 to 400ºF 34lbs @ 24”Hg


Page 44 of 53


Oval Vacuum Cups

Dimensions (mm)

The Vacuforce oval vacuum cups are over molded on a metal support and are ideal for handling longer loads with restricted surface area such as shown below.

Width x Length VOC35x90 VOC35x110 VOC60x140 VOC60x180

Material N NBR S Silicone

Connection Thread 38F G3/8 Female

Part Number Matrix VOC35x90 N – 38F

VOC35x90-38F VOC35x110-38F


Page 44 of 52

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=CUPS.OVAL&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


Oval Vacuum Cups

VOC60x140-38F VOC60x180-38F


Page 41 of 48

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=CUPS.OVAL&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


Foam Vacuum Cups

The Vacuforce EPDM foam vacuum cups are developed for handling very rough or coarse products such as concrete, rough sawn wood, marble and granite etc. The foam seals are available as a spare replacement part and are easily installed on the aluminum cup plate.

Diameter VS100 Ø100 VS150 Ø150 VS200 Ø200 VS300 Ø300 VS400 Ø400

Material E EPDM

Connection Thread 12F VS100, VS150, VS200 34F VS200, VS300, VS400

Part Number Matrix VS200-E-12F

Model A B C D VS300 107.5 19.5 G1/2 G1/8

VS300 157.5 19.5 G1/2 G1/8

VS200 215 34 G1/2, G3/4 G1/8

VS300 315 34 G3/4 G1/8


Page 42 of 48

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaListProducts.jsp&searchText=VACUFORCE.CUPS.VS&stackTitle=^&reqTitle=TITLE_VIAUSERDOCLIST


Vacuum Cup Holders

Level Compensators The Vacuforce level compensators are manufactured from nickel plated brass and utilize stainless steel springs. Available with both internal and external spring mechanisms.


Page 43 of 48

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.LEVEL.COMP&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST


Vacuum Cup Holders

Articulated Ball Joints Typically used with flat vacuum cups, these articulated ball joints allow the vacuum cup to seal against an angled surface. The vacuum flow path is through the centre of the ball joint and therefore this alignment product allows for a very compact installation.

Part Number Thread Size Maximum Load BJ18 G1/8 25kg BJ12 G1/2 50kg


Page 44 of 48

https://www.pneuforce.com/online/validateLogin.jsp?req=https://www.pneuforce.com/online/viaUserDoc.jsp&searchText=VACUFORCE.ARTICULATED.JOINTS&secondPass=1&reqTitle=TITLE_VIAUSERDOCLIST

MODULAR LIFTING SYSTEM

� Integrated vacuum valves� Vacuum venturi or pump operation� Vacuum sensing options� Custom mounting plates� Turnkey vacuum handling

http://www.youtube.com/user/vacuforcesquid

1

Base Box

Vacuum Cups

4

7

Fixed Orifice Fitting

MODULAR LIFTING SYSTEM

Solid Aluminum ConstructionHard Black Anodized FinishCustom Robot Connection Plates Available

Complete Range of Sizes and TypesNitrile, Silicone, Polyurethane & Viton® MaterialsEasy Quick Change Mounting Features

Hard Anodized FinishUniversal Connection ThreadsVarious orifice sizes available

Model Series Dimension A (mm)

Dimension B (mm)

Dimension C (mm)

VFSQ1530 150 300

65*

VFSQ1560 150 600VFSQ15100 150 1000VFSQ3030 300 300VFSQ3060 300 600VFSQ30100 300 1000VFSQ60100 600 1000

Vacuum Velocity Fuse OptionThis mechanical self closing valve consists of the valve body, a stainless steel spring, Nitrile rubber ball and brass adjustment screw. These are installed internal or ex-ternal to the Squid body. If the vacuum cup does not seal against the load being handled the “in rush” of vacuum flow closes the valve, isolating the cup from the rest of the system. This ensures full system vacuum in the rest of the Squid cups attached to the load. This is NOT a check valve. It flows in both directions, to allow vacuum grip and part release.

This valve is flow rate adjustable so that it can be used on different size vacuum cups or even porous surfaces such as low quality card board box handling applica-tions. This is a fully adjustable mechanical valve.

Fixed Orifice Fitting OptionAn alternative to the self closing valve is a fixed orifice fitting. This is the standard option for the Squid system. Each vacuum cup is attached to the Squid body via a fitting with a small orifice. Therefore if the vacuum cup is not sealed against the load, the vacuum source is able to compensate for the small amount of leakage through the small orifice. This is a very simple and effective method of vacuum loss compensation.

Vacuum Pump Option Various options are available for use with the Squid system. Normally on smaller Squid projects a close coupled single stage venturi can be used. On larger models (above 3ft²) a larger multi stage venturi is recommended. On full size palletizing applications where the Squid is handling full layers and/or pallets, regenerative blowers are normally used as this is a more efficient method of vacuum generation. Vacuforce will recommend the vacuum generation method for each application, based on all criteria including user preference.

Vacuforce is able to propose the exact Squid solution for every application. With design and manufacturing in both the USA and Canada, short lead times are assured. With an engineering staff that know vacuum and know your industry, Vacuforce is able to offer superior technical solutions for all your vacuum handling needs.

Standard Models*

*Any size is available Please contact Vacuforce

*65mm is the standard dimen-sion when using a ø40mm single bellow vacuum cup

2

Suction Plate

3

Sealing Foam

Vacuum Control Valves

6

Self Closing Valve/Velocity fuse

Venturi

9

Regenerative Blower

5

PRINCIPLE OF OPERATION

One Piece Aluminum ConstructionHard Black Anodized FinishQuick And Easy Assembly

Very Durable MaterialAble to Seal on Rough or Uneven SurfacesSelf Adhesive Replacement Pads

Direct Acting Poppet ValvesSolenoid and Pilot Operated Spool ValvesFull Flow Orifices for Maximum Performance

Three Piece Design – Easy MaintenanceAdjustable for use on Porous Surfaces (cardboard etc)Universal Connection Thread with Integral Sealing O Ring

Regenerative Blowers – High Flow and up to 21”Hg VacuumPumps for Higher Vacuum Requirements up to 29”HgCentral Pump Stations for Multiple Squid Instal-lations

Single and Multi Stage OptionsClose Coupled to Body of Squid or Off SiteFrom 2CFM to 400CFM Vacuum Flow Rate

8

Call Vacuforce today with your application details! Tel: 1.866.280.3766 | Fax: 1.866.280. 4829www.vacuforce.com

PROJECT TITLE General Description Of Application

Vacuum Generation Preference (please check one)� Compressed Air Venturi� Electrical Vacuum Pump

Compressed Air Venturi If a compressed air venturi is required please complete the following questions� What is the available capacity of the factory installation in CFM?� What is the current maximum line pressure at the installation point in PSI?� What is the maximum diameter of the current compressed air pipe drop?

Electrical Vacuum PumpIf an electrical vacuum pump is required please complete the following questionsWhat voltage is available for electrical supply?� 3 Phase � 115v � 460v � 1 Phase � 230v � 575v

What available space is available for the vacuum pump installation?� Height� Length� Width

Product Being Handled Cycle Time� Weight (lbs) Time in seconds per cycle � Size Length x Width? � Minimum Footprint� Maximum Footprint

The Squid will be a attached to (tick one of the following)� Automated Robot� Gantry Robot� Manual Lifting Rig

Coverage· Is the Squid fully covered by the product? YES NO· If NO what is the minimum percentage of coverage? �%

Forces Being ExertedWhat is the G Force acceleration in the following direction (m/s²)� Lateral� Vertical

Name: Company Name:

Telephone: Email:

See videos at:

APPLICATION Q & A

SearchVacuforce

Call Vacuforce today with your application details! Tel: 1.866.280.3766 | Fax: 1.866.280. 4829

www.vacuforce.com

Ask for our complete components catalogue

Front CoverVacuum VenturiPlastic Body VenturiMulti Stage Classic StyleMini Multi Stage VenturiPart Presence Venturi

Material ConveyorsVacuum SwitchesMechanical Vacuum SwitchDigital Switches

Vacuum ValvesVacuum Velocity FuseDirect Acting Poppet ValvesSolenoid Spool Vacuum ValvesPilot Operated Vacuum Valves

Vacuum FiltersInline Plastic Bowl FiltersSteel Inlet FiltersOil Bath FiltersMini Point of Use Filters

Vacuum CupsB Series Single BellowsF Series Flat Cups

Cup FittingsPA (PFG Style) CupsPB (PJG Style) CupsOval Vacuum CupsFoam Vacuum CupsLevel CompensatorsBall JointsThe Squid!

CV Vacuum Venturi - Air &...

Documents

Transcript of CV Vacuum Venturi - Air &...