Create Standard TCP_IP Port for Print Server

8/3/2019 Create Standard TCP_IP Port for Print Server

1/11

Q: How to setup a Standard TCP/IP Port to print to Print Server?

Here is the procedure for the Standard TCP/IP printer port.

Below procedure can be applied on Windows Vista, Windows XP, Windows 2003, and Windows 2000.

1. Run the Print Server Configuration Utility to get the IP address of your Print Server.

The Print Server Configuration Utility is included in the Administrator Utility which can be downloaded from ourdownload page.

If your Print Server Configuration looks like the following, click on PrintServer Status tab. Take a note about the Active IP address.

If your Print Server Configuration Utility looks like this, get the IP address

Create Standard TCP/IP port for Print Server http://www.edimax.us/html/Faq/FAQ_PS_standardtcpip.ht

1 of 11 12/24/2011 5:23 PM


2/11

It is optional to assign print server a fixed IP address in your network, but we suggest you do so.

In the above Print Server Configuration Utility, click on Setup button and go to TCP/IP, then you can assign a fixed IP address to print server. Inthe above example, our print server has fixed IP address 192.168.123.13. Close Print Server Configuration.

If you have no idea about IP address, you may click here for some basic knowledge for networking.

2. Click on the Start button. Select Run. Type "command" hit OK. Under the Command Prompt, type "ipconfig" hit Enter. You will see the IP

address of your computer. Write down the IP address of your computer. Please note the first three digits of the Print Server IP address should

be the same as the first three digits of your computer IP address. In our example, both use 192.168.123.x IP addresses.


2 of 11 12/24/2011 5:23 PMd d / f i h // di /h l/ / d d i h


3/11

3. Under the command prompt, PING the IP address of your print server. In our example, ping 192.168.123.13 and receive 4 replies. Type Exit

hit Enter to close the command prompt.

4. Click Start menu, go to Printers and Faxes. If you already have a printer driver icon existed, you can skip this step and go to step 5.

Click on Add Printer icon, click Next. Select the option "Local printer attached to this printer" and remove the check on "Automatically detectand install my Plug and Play printer". Click Next.


3 of 11 12/24/2011 5:23 PM

C t St d d TCP/IP t f P i t S htt // di /ht l/F /FAQ PS t d dt i ht


4/11

Select the option "use the following port: LPT1". Click Next.


4 of 11 12/24/2011 5:23 PM

Create Standard TCP/IP port for Print Server http://www edimax us/html/Faq/FAQ PS standardtcpip ht


5/11

Select your printer driver provided by your Windows OS.


5 of 11 12/24/2011 5:23 PM

Create Standard TCP/IP port for Print Server http://www edimax us/html/Faq/FAQ PS standardtcpip ht


6/11

If you do not see your printer in the list, you can click "Have Disk" button and provide the driver or install the printer driver by your printer

manufacturer.

Click Next. You don't need to share the printer and don't print a test page. Click Finish button while the driver is installed successfully. Once you

see the print driver icon created in Printers&Faxes group, you can continue to Step 5.

5. Right click on your printer driver icon and select Properties. Go to Ports tab. Click on Add Port.


6 of 11 12/24/2011 5:23 PM

Create Standard TCP/IP port for Print Server http://www.edimax.us/html/Faq/FAQ PS standardtcpip.ht


7/11

6. Select Standard TCP/IP Port. Click New Port. Click Next.

7. Input the IP address of your print server. Click Next.


7 of 11 12/24/2011 5:23 PM

Create Standard TCP/IP port for Print Server http://www.edimax.us/html/Faq/FAQ PS standardtcpip.ht


8/11

If your print server is a three ports print server, please modify the Port name as IP_192.168.123_p1 for the printer on port 1, IP_192.168.123_p2

for the printer on port 2, IP_192.168.123_p3 for the printer on port 3.

8. Select Custom. Click Setting.

p p q Q_ _ p p

8 of 11 12/24/2011 5:23 PM



9/11

9. Select Protocol: LPR. Input the Queue name: lpt1. Please note, the queue name must be lower case of LPT1 for single port print server. If

you have multiple port print server and the printer is on the second port, the queue name will be lpt2. If the printer is on the third port, the queue

name will be lpt3.

p p q _ _ p p

9 of 11 12/24/2011 5:23 PM



10/11

10. Click OK. Click Next. Click Finish. Click Close. You will be back to the Ports tab.

10 of 11 12/24/2011 5:23 PM



11/11

Check the new created Standard TCP/IP Port. If you have the option "Enable bidirectional support", make sure it is not checked. Click on Apply.

11. Click on the General tab and print a test page.

Note, if you want to enable your Firewall, the LPR protocol uses TCP Port 515. You can follow the above procedure, then in the Exception of the

firewall, add the TCP Port 515. That will make the printing go through your firewall.

11 of 11 12/24/2011 5:23 PM

Create Standard TCP_IP Port for Print Server

Documents

Transcript of Create Standard TCP_IP Port for Print Server