High Power CD Player / Receiver with Changer ControlHigh Power CD Player / Receiver

CQ-5400U/5200UOperating Instructions

Please read these instructions carefully before using this product and save this manual for future use.

2

Panasonic welcomes you to our ever growing family of electronic product owners. We know that thisproduct will bring you many hours of enjoyment. Our reputation is built on precise electronic andmechanical engineering, manufactured with carefully selected components and assembled by peoplewho take pride in their work. Once you discover the quality, reliability, and value we have built into thisproduct, you too will be proud to be a member of our family.

Use This Equipment SafelyWhen DrivingKeep the volume level low enough to be aware of road and traffic conditions.

When Vehicle WashingDo not expose the equipment, including the speakers and CDs, to water or excessive moisture. Thiscould cause electrical shorts, fire, or other damage.

When ParkedParking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior achance to cool down before switching the unit on.

Use the Proper Power SupplyThis equipment is designed to operate off a 12 volt, negative ground battery system (the normal systemin a North American vehicle.)

Use Authorized ServicentersDo not attempt to disassemble or adjust this precision equipment. Please refer to the Servicenter listincluded with this product for service assistance.

Protect the Compact Disc MechanismAvoid inserting any foreign matters to the slot of the compact disc.Failure to observe this may cause malfunction due to precise mechanism of this unit.

Notes: CQ-5400U can be connected to an optional CD changer (CX-DP801EUC, etc.) and an wired remote

control unit (CA-RC350U). CQ-5200U can be connected to an wired remote control unit(CA-RC350U).

For connection and operation for CD changer and wired remote control unit, refer to the operatinginstructions of that units.

A wireless remote control unit (CA-RC500U) is optional (only for CQ-5400U).

Find the model number and serial number on either the back or bottom of the unit. Please record themin the space below and retain this booklet as a permanent record of your purchase to aid inidentification in case of theft.

MODEL NUMBER SERIAL NUMBER

DATE PURCHASED FROM

CQ-5400U/5200U

Note: This operating instruction manual is for two models CQ-5400U and CQ-5200U.The differences between these models are mentioned below. All illustrations throughout this manualrepresent model CQ-5400U unless otherwise specified.

ModelFeaturesWired remote controlWireless remote controlAUX-INCD changer controlS.HDB/LOUDpreamp-out

CQ-5400U

YesYesYesYes

S.HDBYes

CQ-5200U

YesNoneNoneNoneLOUDNone

3

Contents

Use This Equipment Safely ...................................................................Page 2Laser Products ......................................................................................Page 4Part 15 of the FCC Rules ......................................................................Page 4

Power and Sound Controls ......................................................................5How to adjust the volume, mute, balance, and tone for best listening

Radio Basics..............................................................................................8Mode selection, manual and automatic tuning, band selection,preset stations

Compact Disc Player Basics..................................................................11Play, repeat, random and scan

CD Changer Basics.................................................................................13Play, repeat, random and scan, error messages.Note: CD changer controls are applicable to units with optional CD changer unit (sold separeately).

Clock Basics............................................................................................15Setting the time, selecting the clock display, alarm operation

Installation Guide....................................................................................18Step-by-step procedures, electrical connections

Troubleshooting ......................................................................................23Troubleshooting tips, where to get service help

Specifications .............................................................................................26

4

Laser Products (This page describes the standard in the United States only.)

Caution:This product utilizes a laser.Use of controls or adjustments or performance ofprocedures other than those specified herein may resultin hazardous radiation exposure.

Laser products:Wave Length 780 nmLaser Power No hazardous radiation is emitted with safety protection.

Label indications and their locations

Product complies with DHHS Rules 21CFR, Subchapter J in effect as of date ofmanufacture.Matsushita Electric (Taiwan) Co., Ltd.Taipei, Taiwan

MANUFACTURED

Certification Label

Model No.

Manufactrued by Matsushita Electr ic(Taiwan) Co.,Ltd. Taipei TaiwanMade in TaiwanSerial No.

Identification Label

This device complies with Part 15 of theFCC Rules. Operation is subject to thecondition that this device does not causeharmful interference.

12V 4~8Ω 10A FM75Ω

CQ-5400U

Certification label

Identification labelFront

This unit has been manufactured under the Part 15 of the FCC Rules.Do not attempt to make any changes or modifications to this unit.

Part 15 of the FCC Rules

5

Power and Sound Controls

PowerIf the vehicle is not running yet, turn the key in the ignition until theaccessory indicator lights.Press [PWR] to switch on the power.

Changing Audio ModesPress this knob [SEL] to change the audio mode as follows.

VOL a BASS a TRE(Volume) (Treble)

c dFADE b BAL

(Fader) (Balance)

Volume Press the knob to select the volume mode and then turn it

clockwise or counterclockwise to increase or decrease the volume.

Turn the knob clockwise or counterclockwise more than 0.5seconds to change the numeric level in sequence.

Bass and TreblePress the knob to select the BASS (TREBLE) mode and then turn itclockwise or counterclockwise to increase or decrease thebass/ treble level.

0 to 40

-12 to 12 -12 to 12

Volume Level

Anti-Volume-Blast CircuitThis unit has a safety function which slowly raises volume levelwhen power is switched back on after it is turned off at a specificlevel (20) or higher.

d

6

FaderPress the knob to select the FADER mode and then turn itclockwise or counterclockwise to shift the sound volume to the frontor rear speakers.

S•HDB (Super High Definition Bass)(Only for CQ-5400U)Especially for rock music, the bass-sound will be more powerful. Press and hold [BAND] (S•HDB) for more than 2 seconds to be

able to listen to high-definition bass.

Press and hold [BAND] (S•HDB) for more than 2 seconds toreturn to the normal tone.

Note: In the audio mode (BASS/TRE/BAL/FADE), the displaywill be back to regular operation mode with no operation formore than 5 seconds (2 seconds in the VOL mode).

or R 1 to 15 Fader Center

Tone Enhancement (Loudness)(Only for CQ-5200U) Press and hold [BAND] (LOUD) for more than 2 seconds to

enhance bass and treble tones when listening at low or mediumvolume.

Press and hold [BAND] (LOUD) for more than 2 seconds again todeactivate when listening at higher volumes.

Power and Sound Controls (continued)

(F: Front, R: Rear)

Press and hold

Press and hold

BalancePress the knob to select the BALANCE mode and then turn itclockwise or counterclockwise to shift the sound volume to the rightor left speakers.

or L 1 to 15 Balance Center(R: Right, L: Left)

7

Power and Sound Controls (continued)

Mute Press [MUTE] to mute the sound completely.

Press [MUTE] again to cancel.

Selecting Auxiliary Source(Only for CQ-5400U) Press and hold [MODE] (AUX) for more than 2 seconds to select

AUX Input mode.

Connect the auxiliary equipment (any other appropriateequipment) to AUX IN Connector.

Canceling AUX Input modePress [MODE] (AUX) to resume the previous mode.

Press and hold

8

Radio Basics

Mode SelectionPress [MODE] to change the operation mode as follows.

Radio a CD a CD changer (when connected)c d

(Press and hold [MODE] for morethan 2 seconds.)(only for CQ-5400U)

To change to the tuner modeIn case of CD changer mode or CD mode, press [MODE].

Selecting a BandPress [BAND] to change the band setting as follows.

FM1 a FM2 a W/B a AM(Weather Band)c d

"ST" indicator lights during reception of an FM stereo broadcast.

Manual TuningPress [TUNE jj] or [TUNE ii] to tune in a higher or lowerfrequency.

Seek TuningPress and hold [SEEK jj ] or [SEEK ii ] for more than 0.5seconds, then release it.Seeking will automatically stop when a signal of the next broadcaststation is received.

Hold and release

AUX

9

Station PresetFM1, FM2 and AM can save maximum 6 stations each in their preset station memories.

Manual Station Preset Press [BAND] to select a desired band. Use manual or seek tuning to find a station which is to be preset

in the memory. Press and hold one of the preset buttons [1] to [6] until the

display blinks once.

Note: You can change the memory setting by repeating the aboveprocedure.

Tuning in a Preset StationPress the corresponding preset buttons [1] to [6] to tune in a presetstation.

Auto Station PresetSelect a band and press and hold [SCAN] (AUTO PRESETS) formore than 2 seconds. The 6 strongest available stations will be automatically saved in

the memory on preset buttons [1] to [6]. Once set, the preset stations are sequentially scanned for 5

seconds each.Notes: In the case of Auto Station Preset, only FM2 is available for FM

stations. (FM1 is not available.) Auto Station Preset is not activated in a Weather Band. The stations manually preset on the Selected band will be

deleted.

Preset Number

Radio Basics (continued)

d

d

Caution: To ensure safety, never attempt to preset stations while you are driving.

10

Tuning in a Weather BandStationPress any of the buttons [1] to [6] to tune in the station preset bythe previous page.

Weather Band StationsNational Weather Radio Broadcasts from over 380 locationsthroughout the U.S. on seven VHF/FM frequencies.Tune to weather band to receive continuous weather information 24hours a day on one of the following frequencies.

1. 162.550 MHz2. 162.400 MHz3. 162.475 MHz4. 162.425 MHz5. 162.450 MHz6. 162.500 MHz7. 162.525 MHz

Occasionally the frequency of an existing or planned station mustbe changed because of unexpected radio frequency interferencewith adjacent NOAA Weather Radio Stations and/or with otherGovernment or Commercial Operations within the area. If you havea question concerning NOAA Weather Radio, please contact yournearest National Weather Service Office.

Note: The weather band (CH1-6) has been preset in advance.CH7 is selected by pressing [jj] or [ii].

WB Weather Band Frequency Channel Number

The frequency (162) remains unchanged.

11

Compact Disc Player Basics

Disc InsertInsert the disc and play starts automatically.

"LOAD" will be displayed until the disc is loaded. Play starts fromthe first track.

Note: While the disc is in the deck, " " indicator lights.

Disc EjectionPress [u] to stop CD play, and the disc will be quietly ejected fromthe CD slot. (During disc ejection, "EJ" will be displayed.)

Track Selection Press [jj] once to go to the next track. Press [ii] once to play from the beginning of the track you are

listening to. Press twice to play the previous track. Press repeatedly to skip the desired number of tracks.

Track Search Press and hold [jj] or [ii] for more than 0.5 seconds to activate

fast forward or reverse. Release [jj] or [ii] to resume the regular CD play.

Caution: Do not use irregularly-shaped (heart-shaped, octagonetc.) CD. Failure to observe this may cause malfunction.

Disc

Disc

Disc

Disc

Hold and release

12

Track Repeat Press [3 REP] to repeat the current selection.

Press [3 REP] again to cancel.

Random Selection Press [6 RAND](RAND: RANDOM). A random selection of music

is played from all available tracks.

Press [6 RAND](RAND: RANDOM) again to cancel.

Track Scan Press [SCAN]. The display will blink and the first 10 seconds of

each track on the disc play in order.

Press [SCAN] again to cancel.

REPEAT

RANDOM

Disc

13

CD Changer Basics (Only for CQ-5400U)

Starting the CD ChangerOnce the CD changer has been connected, press [MODE] tochange to the CD changer mode. when a disc magazine isinserted, CD play starts automatically.

Disc SelectionPress [4] (i DISC) or [5] (DISC j) to select a disc in descendingor ascending order.

Then, the selected disc will start to play from the first track.

Note: The number of discs you can load the CD changer with isspecific to each model.

Track Selection Press [jj] to advance to the next track. Press [ii] to start play from the beginning of the track now playing. Press [jj] or [ii] repeatedly to skip the desired number of tracks.

Track Search Press and hold [jj] or [ii] for more than 0.5 seconds to activate

fast forward or reverse. Release [jj] or [ii] to resume regular CD changer play from the

released position.

Note: CD changer functions are designed for an optional CD changer unit.

PlayTime

DiscNumber

TrackNumber

Hold and release

Press and hold

14

0000

E 3E 1

E 2

Track Repeat Press [3 REP] to repeat the current selection. "REPEAT" indicator

lights.

Press [3 REP] again to cancel.

Random Selection Press [6 RAND](RAND: RANDOM). A random selection of music

is played from all available discs/tracks.

Press [6 RAND](RAND: RANDOM) again to cancel.

Note: The Random mode will stop and the disc select function willoperate once the [ii] DISC or DISC [jj] is pressed.

Track Scan Press [SCAN]. The display blinks and the first 10 seconds of each

track on the discs play in sequence. Press [SCAN] again to cancel.

Error Display Messages

Appears on the display when thecompact disc is dirty or inverted.Selects the next available compactdisc.

Appears on the display whencompact disc is scratched. Selectsthe next available compact disc.

Appears on the display when thereis no disc in the magazine.

Appears on the display when theCD changer stops operating forsome reason. Please turn off thevehicle engine (ACC off) andremove the fuse from yellow leadfor 1 minute. Then reinstall the fuse.

REPEAT

RANDOM

15

Clock Basics (The clock system is 12-hours.)

Initial Time Press and hold [CLK] until you have set the time, "AM 12:00"

blinks, and the time setting mode is activated.Press [ii] to set the hour.Press [jj] to set the minute.(Hold [ii] or [jj] to change numbers rapidly.)

Once the time has been set, release [CLK].

Note: When the clock is not set yet, "SET" is displayed.

Time ResetWhen you want to reset the time, repeat steps to above.

Clock DisplayPress [CLK] to display the current time.After a few seconds, current time returns on the display.

Note: The current time will be displayed at all the time even thepower of the radio is turned off.

d

or

Press and hold

16

Alarm Time Setting Press and hold [ALM] until you have set the alarm time, "AM

12:00" blinks , and the alarm time setting mode is activated.Press [ii] to set the hour.Press [jj] to set the minute.(Hold [ii] or [jj] to change numbers rapidly.)

When you have set the alarm time, release [ALM].

Note: When the alarm is not set yet, "AM 12:00" is displayed.

Alarm Time ResetWhen you want to reset the alarm time, repeat steps to above.

Alarm Operation Alarm is switched to ON or OFF each time [ALM] is pressed. When the alarm is switched to ON, the alarm sound will activate

at the set alarm time.

Turning off the Alarm SoundThe alarm sound will turn off automatically after 90 seconds.Otherwise, press [ALM] once.

Cautions: Be careful not to set wrong alarm time, otherwise, the alarm may sound while driving. If the alarm is set, be sure to check the set alarm time by pressing and holding [ALM] for more than

2 seconds. If volume is set at "0" step, the output volume will be muted. (Even when ALARM is acting.)

d

or

Alarm output Volume SelectionYou can select ALARM VOL 1 (or VOL 2) by pressing [ALM] insequence and the display will show as follows.

ALARM TIME a ALM VOL 1 a ALM VOL 2(display 3 seconds) (display 2 seconds) (display 2 seconds)

OFF

Press and hold

17

If abnormal Operation appearsReset SwitchUse a unflexible thin stick to press this switch in the hole.The initial settings will resume and all electronic memorysettings previously registered will be lost.

18

Installation Guide

This installation information is designed for experienced installersand is not intended for non-technical individuals. It does notcontain warnings or cautions of potential dangers in attempting toinstall this product.Any attempt to install this product in a motor vehicle by anyoneother than qualified installer could cause damage to the electricalsystem and could result in serious personal injury or death.

WARNING

OverviewThis equipment should be installed by aprofessional. However, if you plan to install thisunit yourself, your first step is to decide where toinstall it. The instructions in these pages willguide you through the remaining steps: (Pleaserefer to "WARNING" statement above).

Identify and label the vehicle wires. Connect the vehicle wires to the wires of the

power connector. Install the unit in the dash. Check the operation of the unit.

If you do encounter problems, please consultyour nearest professional installer.

Caution: This unit will operate with a 12 volt DCnegative ground auto battery system only. Donot attempt to use it in any other system. Doingso could cause serious damage.

Before you begin installation, look for the followingitems included in the packing with your unit.

Installation Hardware ...... Needed for in-dashinstallation

Installation HardwareNo.

1

Item

Mounting Collar

Diagram Qty

19

Installation Procedures

Note: Disconnect the cable from the negative (–) battery terminal.

2. Securre the rear of the unit.a) Insert Power Connector to the unit.b) Check the electrical connection by referring to this operating instructions.c) Insert the unit into Mounting Collar and push it in until "click" is heard.

1. Secure the Mounting Collar .Insert Mounting Collar into the vehicle's dashboard, and bend mounting tabs out with ascrewdriver.

When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injureyour hands and fingers.

We strongly recommend you to wear gloves for installation work to protect yourself from injuries.

20

To remove the unit from the vehicle's dashboardInsert Dismounting Pins and pull both pins.

Note: Do not lose Dismounting Pins. They will be needed to remove the unit from the vehicle'sdashboard.

Dimounting Pin(U-shaped)

21

Electrical ConnectionsCautions: This product is designed to operate with a 12-volt negative ground battery system. To prevent damage to the unit, be sure to follow the connection diagram below. Do not insert the power connector into the unit until the wiring is completed. Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle

all cables and keep cable terminals free from touching any metal parts.

To AUX

(Red)(R)

(L)

(R)

(L)(Rear)

(White)

Preamp-Out

(Red)

(White)

AUX-In

Pre-Out

(Rear Side)

Wired Remote Control Connector(Connect to CA-RC350U)

CD Changer Control Connector

Power Lead (ACC or IGN)To ACC power, +12V DC

Ground LeadTo a clean, bare metallic part ofthe car chassis

Battery LeadTo the car battery, continuous+12V DC

Dimmer Control LeadConnect to vehicle dimmer control lead

Amp. Cont(MAX 0.1A) (Blue)

(Red)ACC

Ground (Black)

(Yellow)Battery

Dimmer(Orange w/White stripe)

Power Connector

(Violet)

(Violet w/black stripe)(Gray w/black stripe)

(Green)(Greenw/blackstripe)

(Whitew/blackstripe)

(Gray)(white)

Left Speaker(Front)

Right Speaker(Front)

Left Speaker(Rear)

Right Speaker(Rear)

CD ReceiverCQ-5400U

Antenna

(only for CQ-5400U)

22

Electrical ConnectionsCautions: This product is designed to operate with a 12-volt negative ground battery system. To prevent damage to the unit, be sure to follow the connection diagram below. Do not insert the power connector into the unit until the wiring is completed. Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle

all cables and keep cable terminals free from touching any metal parts.

(Rear Side)

Wired Remote Control Connector(Connect to CA-RC350U)

Dimmer Control LeadConnect to vehicle dimmer lead

(Red)ACC

Power Connector

(Black)

(Yellow)Battery

Ground

(Violet)

(Violet w/black stripe)(Gray w/black stripe)

(Green)(Greenw/blackstripe)

(Whitew/blackstripe)

(Gray)(white)

Left Speaker(Front)

Right Speaker(Front)

Left Speaker(Rear)

Right Speaker(Rear)

CD ReceiverCQ-5200U

Antenna

Power Lead (ACC or IGN)To ACC power, +12V DC

Ground LeadTo a clean, bare metallic part ofthe vehicle chassis

Battery LeadTo the vehicle battery, continuous+12V DC

Dimmer (Orange w/White stripe)

(only for CQ-5200U)

23

E 1

E 2

E 3

Troubleshooting

MaintenanceYour product is designed and manufactured toensure a minimum of maintenance. Use a softcloth for routine exterior cleaning. Never usebenzine, thinner, or other solvent.

When Something Doesn't WorkCheck the charts on page 22 for possible causesand solutions to any problem you might beexperiencing. Some simple checks or minoradjustments may eliminate the problem.

Product ServicingIf the suggestions in the charts do not solve theproblem, we recommend that you take it to yournearest authorized PASC Servicenter. The unitshould be serviced only by a qualif iedtechnician.

Error Display Messages

Appears on the display when thecompact disc is dirty or inverted.The disc is ejected automatically.But, the disc may be ejectedautomatically, even if this errormessage is not displayed.

Appears on the display whencompact disc is scratched. The discis ejected automatically.But, the disc may be ejectedautomatically even if this errormessage is not displayed.

Appears on the display when thecompact disc stops operating forsome reason. Please turn off thevehicle engine (ACC off) andremove the fuse from yellow leadfor 1 minute or more. Then reinstallthe fuse.

24

Troubleshooting (continued)

Troubleshooting TipsPROBLEM

Unit does not turn on.

Radio has static.

Radio memory buttons do notwork.

No sound can be heard even ifthe disc is properly loaded.

Sound distorted due to vibration

Inverted sound (Left/Right conn-ections.)

No sound from front or rearspeakers

Sound distorted due to vibration

A compact disc is sometimesejected. (Display shows "E1", anerror message.)

POSSIBLE CAUSEDead vehicle batteryIgnition or ACC is not on.Bad power line connection

Antenna not hooked upClose to high power lines

Not holding buttons down longenough

The compact disc is inverted.

The compact disc is dirty.

The temperature inside thevehicle is more than 140°F (60°C)

Excessive moisture

Wiring connection is not properlydone.

Volume control is at "minimum"position.

Fuse of amplifier is blown out.

Installing method is bad.

The speaker cords are inverted.

The fader control is set on thewrong position.

The compact disc may bedefective.

The compact disc is dirty.

The pickup lens is dirty.

PROBABLE SOLUTIONCharge vehicle battery.Turn ignition to On or ACC.Check connections.

Hook up antenna.Move away from high power lines.

Press and hold buttons for morethan 2 seconds.

Insert the disc with label sidefacing up.

Try to clean the compact disc byinstructions of disc cleaning.

Give the interior a chance to cooldown before using the unit.

Wait for a while before using theunit.

Confirm all wiring connectionsuch as power cord, speakercords, etc.

Adjust the volume control to theproper level.

Replace the fuse with the correctrating.

Fix the unit securely.

Check the speaker cords.

Adjust the fader control of theunit correctly.

Try to replace the disc withanother one.

Try to clean the compact disc byinstructions of disc cleaning.

Clean the lens. (Use CD lenscleaning disc.)

25

Caution for use of a newDiscA new disc may have rough edges on its inner and outerperimeter. If a disc with rough edges is used, propersetting will not be possible and the CD player will notplay the disc. Therefore, remove the rough edges inadvance by using a ball-point pen or pencil as shown onthe right. To remove the rough edges, press the side ofthe pen or pencil against the inner and outer perimeterof the disc.

Rough edgeson outer perimeter

A ball-point penor pencil

Rough edgeson inner perimeter

Special Notes

Dirt, dust, scratches and bending of disc will causemisoperation. Handle discs with care.

Do not place stickers or make scratches on disc. Do not bend discs. Disc should always be kept in the case when not in

use to prevent from damaging. Do not place discs in the following places:

1. Direct sunlight2. Dirty, dusty and damp areas3. Near vehicle heaters4. Seats and dashoard

Do not use irregularly-shaped (heart-shaped,octagon etc.) CD. Failure to observe this may causemalfunction.

Disc CleaningUse a dry soft cloth to wipe the surface. If the disc isquite dir ty use a soft cloth slightly dampened inisopropyl (rubbing) alcohol. Never use solvents suchas benzine, thinner, conventional record cleaner, ormopper as the may mar the surface of the disc.

ONLY USE DISCS CARRYING LABEL SHOWN ON THE RIGHT

Label

Do not touch theunderside of thedisc.

Do not bend.

Wipe the disc from center to outsidedirection.

Notes on Compact Discs

26

SpecificationsGeneral

Power Supply : 12 V DC (11V-16V) Test Voltage 14.4V, Negative groundMaximum Power Output : 37 W × 4 channels at 400 Hz, Volume Control maximumPower Output : 18 W per channel into 4 ohms, 40 to 30,000Hz at 3% THD.Tone Action : Bass; ± 12 dB at 100 Hz

Treble; ± 12 dB at 10 kHzCurrent Consumption : Less than 2.5 A (CD mode, 0.5 W 4-speaker)Speaker Impedance : 4 Ω (4-8 Ω acceptable)Dimensions (W × H × D) : 7" × 1-15/16" × 5-7/8" (178 × 50 × 150 mm)Weight : 3 lbs. 3 oz. (1.44 kg)

AM Radio

Frequency Range : 530-1,710 kHzUseable Sensitivity : 28 dB/µV (25 µV/ S/N 20 dB)

FM Stereo Radio

Frequency Range : 87.9-107.9 MHzUseable Sensitivity : 12 dBf. (1.1 µV / 75Ω, S/N 30 dB)50 dB Quienting Sensitivity : 17 dBf. (1.8 µV / 75Ω)Frequency Response : 30-15,000 Hz ± 3 dBAlternate Channel Selectivity : 75 dBStereo Separation : 35 dB at 1,000 HzSignal/Noise Ratio : 70 dB (Mono)

Weather Band Radio

Frequency Range : 162.40-162.55 MHzUseable Sensitivity : 3 dB/µV (S/N 20 dB)Signal/Noise Ratio (40 dB/µV) : 50 dB

CD Player

Sampling Frequency : 32 times oversamplingDA Converter : MASH•1 bit/4 DAC SystemError Correction System : Panasonic Super Decoding AlgorithmPick-Up Type : 1-beamLight Source : Semiconductor laserWavelength : 780 mmFrequency Response : 20 - 20,000 Hz (±1 dB)Signal to Noise Ratio : 85 dBTotal Harmonic Distortion : 0.01% (1 kHz)Wow and Flutter : Below measurable limitsChannel Separation : 75 dB

*Above specifications comply with EIA standards.

Note: Specifications and design are subject to modification without notice due to improvements intechnology.

Panasonic Consumer ElectronicsCompany, Division of MatsushitaElectric Corporation of AmericaOne Panasonic Way, Secaucus, New Jersey 07094

YFM284C336ZA TAMACO0900-0 Printed in Taiwan