Configuration of Helios Pico Repeater New

8/16/2019 Configuration of Helios Pico Repeater New

1/14

Express Instruction

1.

Launch NMS UtilityDouble click on the NMS shortcut icon on the desktop to launch the NMS utility first.

2. Choose Mode

If it has no modem, and connects to repeater directly, it will approach to the Local control Mode.

Or if it connects with the Modem, it will approach to the Remote control Mode.

Main Windows lists as below picture:


2/14

3. Create Sites

Follow the steps in turns to create: Region District Site

a. Right click on the any area of the “Create Sites”, then click on „Add Region(R)‟ to create

„Region‟, supposed named as “China”.

b. Right click on the Region‟China‟, and then click on „Add District‟ to create the District,

supposed named as‟ Fujian. ‟

c. Right click on the District „Fujian‟ , and then click on „Add Site‟ to create the Site, supposed

named as‟Xiamen „.

4. Fill Site Information

After created the Site, then launch the site information management window for filling.

a.

Right click the Site „Xiamen‟, then click the „Equipment Basic Info(I)‟ to launch the

Site Information management window.


3/14

Site Information window

Firmware Ver.: Firmware version.

Backup Battery: It is available only when the system has Backup Battery Unit.

Applicable in GSM, DCS, WCDMA, CDMA:

Select the wanted system, supposed GSM, then its following „Band Selective‟ or „Channel

Selective‟ mode will be available to selection, the „Channel Nr.‟ Item is only available after tick

off Channel Selective mode.

Above operation same to DCS /WCDMA/CDMA system for selection.

Note:

Channel Nr is a full name of Channel Number. Only available under tick off the channel selective

mode, and it shows that the repeater provided configurable Channel quantities.

①

①

②

②

③

③


4/14


5/14

A.3. Set detailed Parameters on each Systems (GSM &DCS)

A.3.1 open the Local console window

Double Click the corresponding created site name in the Main Window or right click the

created site name and then click „RF / Status(S)‟ to launch „Local / Remote Console‟

window. Refer to Pic2 Local Console Window

Local Console window

Note: after above general initial parameters setting, the support systems will tick off on the GSM

&DCS, other systems are not available to choose, unless return to Step A.2 to reset the

requested system.

A.3.2 Read the repeater detailed Parameters in support system (GSM/DCS)

Recommend to read the repeater history information before set parameters.

Click the Monitoring sheet and then click the RF/Status sheet then:

① Select support system(GSM/DCS)

② click button „Get RF/Status‟ to read the history information.


6/14

A.3.3 Set the repeater RF/Status Parameters in support systems (GSM/DCS),refer to Pic3

Click the Configuration sheet and then click the RF/Status sheet then:


② click button „Get RF/Status‟ to read the history information

③ Set the wanted status and parameters for PA ,PA ATT ,LNA ATT, O/P Power

Threshold, AGC Enable, Max Gain as which lists on the Pics3


7/14

A.3.4.2 Set Channel number for fixed bandwidth(for UL) and 1 tunable Sub-bands(for DL)

in DCS System: Click the Configuration sheet and then click the Channel sheet then:

① Select support system(DCS)

② Set fixed bandwidth for UL

Just set the requested central frequency channel number in W1

③ Set 1 tunable sub-band for DL

Just set the requested starting channel number in S1 and end channel number in S2

Note: keep the channel switch as default .

Set channel numbers for DCS system

Note: After set all the parameters, recommend return to MonitoringRF/Status page to determine the

setting parameters.

Set Channel number s for GSM tunable sub-band


8/14

Below Instructions B suitable for the repeaters with SN:

(SN:12040041, 12040042, 12040043, 12040044, 12040045, 12040046, 12040056, 12040057,

12040058, 12040059, 12040060, 12040061, 12040062, 12040063, 12040064, 12040065,

12040066, 12040067, 12040068, 12040069)

E.g: Instructions to set parameters for GSM&DCS Dual band Pico repeater with output

power 20dBm, 3 Fixed sub-bands(GSM:2 Fixed sub-bands for UL&DL; DCS:1 Fixed

sub-band for UL&DL), corresponding site named as Xiamen:

B.1. create site name first as above steps of „3.create site‟.

B.2. Set general initial parameters for repeater, the steps as following:

① Select correct Equipment_Type as: Band Selective Repeaters

② Select the GSM,DCS system (Do not select WCDMA ,CDMA while the repeater does not

includes these two systems).

③ Select the „Channel Selective‟ item both on GSM and DCS systems

④ Set Channel Nr as 2 for GSM system (because GSM system has 2 Fixed sub-bands) ,

and set Channel Nr as 1 for DCS system (because DCS system has only 1 fixed sub-band)

⑤ After all the parameters are setting complete, then click the button „Modify(M)‟

⑥ Click the button „Done(D)‟ to finally confirm all the setting.

please refer to below < Pic1> Site Information management

< Pic1> Site Information management


9/14

B.3. Set detailed Parameters on each Systems (GSM &DCS)

B.3.1 open the Local console window



window. Refer to Pic2 Local Console Window

Local Console window

Note: after above general initial parameters setting, the support systems will tick off on the GSM

&DCS, other systems are not available to choose, unless return to Step A.2 to reset the

requested system.

B.3.2 Read the repeater detailed Parameters in support system (GSM/DCS)

Recommend to read the repeater history information before set parameters.

Click the Monitoring sheet and then click the RF/Status sheet then:


② click button „Get RF/Status‟ to read the history information.


10/14

B.3.3 Set the repeater RF/Status Parameters in support systems (GSM/DCS)

Click the Configuration sheet and then click the RF/Status sheet then:


② click button „Get RF/Status‟ to read the history information

③ Set the wanted status and parameters for PA ,PA ATT ,LNA ATT, O/P Power

Threshold, AGC Enable, Max Gain as which lists on the Pics3


11/14

sub-band

Keep channel Switch parameters as default.

Please refer to below Set Channel numbers for GSM 2 fixed sub-band

B.3.4.2 Set Channel number for 1 fixed bandwidth(for UL&DL) in DCS System: Click the Configuration sheet and then click the Channel sheet: ①Select support system(GSM)

②Set requested central frequency channel numbers for 1 fixed sub-bands in UL1&DL1UL1&DL1: for the fixed sub-band;

UL1 is the central frequency channel number for uplink

DL1 is the central frequency channel number for downlink,

UL1&DL1 combined parameters to set the request frequency range in the fixed

sub-band.

Keep channel Switch parameters as default

Pleaser refer to Set Channel numbers for DCS 1 fixed sub-band

Set Channel numbers for GSM 2 fixed sub-band


12/14

Set Channel numbers for DCS 1 fixed sub-band

Note: After set all the parameters, recommend return to MonitoringRF/Status page to determine

the setting parameters.


13/14

Below Instructions C suitable for the repeaters with SN:

(SN:12040076, 12040077, 12040078, 12040079, 12040080, 12040081, 12040082, 12040083,

12040084, 12040085)

E.g: Instructions to set parameters for UMTS Single bands Pico repeater with output power

27dBm, corresponding site named as Xiamen:

C.1. create site name first as above steps of „3.create site‟.

C.2. Set general initial parameters for repeater, the steps as following:

① Select correct Equipment_Type as: MicroRepeaters

② Select the WCDMA system (Do not select other systems while the repeater does not

includes them).

③ Select the „Band Selective‟ item on WCDMA systems

④ After all the parameters are setting complete, then click the button „Modify(M)‟

⑤ Click the button „Done(D)‟ to finally confirm all the settings.

please refer to below < Pic1> Site Information management

Site Information Management

C.3 open the Local console window


14/14



window.

C.4 Set Set Channels numbers for 1 fixed Sub-bands(both for UL&DL) in WCDMA System

① Select support system(WCDMA)

Set requested central frequency channel numbers in UL1&DL1

UL1 Center Fre(KHz):is the central frequency channel number for uplink

DL1 CenterFre(KHz): is the central frequency channel number for downlink,

UL1&DL1 combined parameters to set the request frequency range for fixed

sub-band.

Set fixed bandwidth for WCDMA

Set fixed bandwidth for WCDMA

Note: After set all the parameters, recommend return to MonitoringRF/Status page to determine

the setting parameters.

Configuration of Helios Pico Repeater New

Documents

Transcript of Configuration of Helios Pico Repeater New