Confidential1 Panasonic Communications Co., Ltd. Network Business Company Edition 1.3 07 Jul., 2004...

Confidential 1

•Panasonic Communications Co., Ltd.•Network Business Company•Edition 1.3 07 Jul., 2004

Enhanced Items

KX-TDA200/100 System (Ver.1.1)

Confidential 2

General

-System Highlight

- New Features

- Condition of New Features

- Software Compatibility

Confidential 3

V1.0

V1.1

Networking(QSIG), Call Center, VoIP Gateway,

CTI (CSTA/TAPI), T76xx Line Up, Wireless System

- Digital XDP & Double Extension Capacity by MEC - New VoIP Gateway Card (Panasonic proprietary)- New CS to DPT Port- And other new features

System Highlight

Confidential 4

BRI4, IPGW4E, CSIF4, 2chCS, MECDXDP & Double Extension CapacityNew IPGW Card2chCSBroadcastingDialing PlanExt. CLIP sending on Emergency CallShort Cut Access to System Speed DialModified DDI Number is displayed on LCDImproved DSS LED Flash / Call Pick upDisable Hold RecallDisable re-count Ext-CO Duration Limitation by Hold RetrieveISDN-3party ConferenceDTMF Tone through a Conference from PTIntercept Timer for each time mode(Day/Night/Lunch/Break)SMDR RC/AN information outputPaging to other paging groupCOS Name is programmableCS port Name is programmableExt. CLIP Automatic GeneratingDDI/DID Name Automatic GeneratingWireless XDP Programming from PCLogical CheckPS Hand-Over during Conference CallWalking Extension from Fault Extension

HardwareFunction

Improvement

Highlight

Making calls

Receiving calls

Hold/FWD/TR

Conference

TimerOthers

Programming

New Features

Confidential 5

New FeaturesDXDPDouble Extension Capacity2chCSBroadcasting

Another Features

Software ConditionDHLC/DLC = 2.005DHLC/DLC = 2.005DHLC/DLC = 2.005

No

No

Hardware ConditionNo

MEC(TDA0105)No

MEC(TDA0105)

No

Condition of New Features

Confidential 6

Software CompatibilityMPR / LPR

MPR 1.1xxMPR 1.0xx

YES

YES w/o DXDP, TDA0141

YES

YES

DLC/DHLC 2.005DLC/DHLC 1.xxx

MPR / PC maintenance console

MPR 1.1xxMPR 1.0xx

YES

NO

YES

YES

1.071.06

Confidential 7

Hardware

- New Hardware

- Power Factor Summary

Confidential 8

CSIF4(4 Cell Station Interface)

KX-TDA0143

4-port CS interface card for 4 CSs(TDA0142).

MEC(Memory Expansion Card)

KX-TDA0105

2ch CS(CS to DPT Port)

KX-TDA0141

* Memory expansion for - Broadcasting feature - Double the number of DPTs (DXDP)* To be installed in the MEC slot on MPR card

Connect to DPT port (CSIF card is not needed)2.4GHz (KX-TDA0141), DECT(KX-TDA0141CE)

IPGW4E(4ch VoIP Gateway)

KX-TDA0484

TDA200 4TDA100 2

TDA200 4TDA100 2

TDA200 1TDA100 1

TDA200 32TDA100 16

4-channel VoIP gatewayVoIP H.323 V.2, ITU-T G.729a, G.723.1, G.711T38 (FAX) is not supportedPanasonic proprietary IPGW card

New Hardware

Confidential 9

* Calculated with base card, not using base ports.

IPGW4

PRI-30

BRI-8

BRI-4

CID (CO)

E1

E&MLCOT-16

LCOT-8LPR Card

TDA0480

TDA0290

TDA0288

TDA0284

TDA0193

TDA0188

TDA0184TDA0181

TDA0180Model

0

0

0

0

0

0

00

0Power units

IPGW4E TDA0484 0

MSG

RMT

TDA0191

TDA0196

0

0

CTI-LINK TDA0410 0

Echo

DPH-2/4

TDA0166

TDA0161/162

0

0

MEC TDA0105 0

Trunk Card Extension Card

Other Terminals

Voice Mail (D-PT)

T72xx/T74xx/T75xx

BRI Extension

T76xx, T7560, T7565 1/Extension

2/Port (2ch)

4/Extension

2/Port (2ch)

CS (TDA0142) 4/CS

CS (TDA0141) 4/CS

APT & DSS console 4/Extension

SLT 0

MSLC-16

SLC-16

DHLC-8

DLC-16

DLC-8

SLC-8

LPR Card Model Power units

CS I/F-8

TDA0175

TDA0174

TDA0170

TDA0172

TDA0171

TDA0173

TDA0144

16/Card*

16/Card*

8/Card*

0

0

8/Card*

0

CS I/F-4 TDA0143 0

Power factor summary (Ver. 1.1)

Confidential 10

Function - Highlight

- DXDP & Double Extension Capacity

- New IPGW Card

- 2ch CS

Confidential 11

- DPT on DPT without additional HW or SW

- Easy installation for additional Extensions

- 1 DHLC port => 3 telephones (2x DPT+1x SLT)

* DHLC Card = Max 24 Ext.

- 1 DLC port => 2 telephones (2x DPT)

* DLC16 Card = Max 32 Ext.

* DLC8 Card = Max 16 Ext.

DXDP-Slave

XDPor

4 Wires 4 Wires 2 Wires

XDP

4 Wires 2 Wires

2 Wires

DHLC Port

DHLC Port

SLTSLT

SLTSLT

DXDP-Master

2 Wires

DXDP-Slave

2 WiresDLC Port

2 Wires 2 Wires

2 Wires

DHLC PortSLTSLT

Digital XDP (DXDP) -1

Confidential 12

Capacity for ExtensionV1.0 V1.1

DXDP

MEC

TDA100

TDA200

No

No

Yes

No

Yes

Yes

Max 64 Ext.

Max 128 Ext.

Max 64 Ext.

Max 128 Ext.

Max 128 Ext.

Max 256 Ext.

Additional DPT can be installed without buying another DHLC or DLC, but total capacity does not change without MEC.

System Capacity (Trunk & Extension mixed)

V1.0

TDA100 80 (108) portsTDA200 160 (216) ports

V1.1 with DXDP&MEC

TDA100 144 (158) portsTDA200 288 (316) ports


Confidential 13

MEC(TDA0105) How to check the TDA0105 If the TDA0105 is not installed.

If the TDA0105 is installed.

Click”

If connected extension is exceed 128 with M type PSU, what happens?

- 129th Extension (PT) will not come in service. - Minor error log = PT Connection Over.

DHLC-8 8 (Fixed) + Connected PT/DSS/VMSLC-8 8 (Fixed)DLC-8 Connected PT/DSS/VMSLC-16 16 (Fixed)DLC-16 Connected PT/DSS/VM

PU for extension cards


Confidential 14

Condition-3

- OHCA function can not be used

- T7601 (USB) can not be used

(PC Phone / PC Console / PC Programming)

Master Slave

- T7625- T7630- T7633- T7636- T7665

- T7625- T7630- T7633- T7636- T7665

Telephone

Can be used

- A-PT- T72xx- T74xx- T75xx- DSS

- A-PT- T72xx- T74xx- T75xx- DSS- CS

Can not be used

Condition-2DXDP-Slave

ø0.4mm Max.40mø0.5mm Max.50mø0.6mm Max.60m

DXDP-Master

Condition-1 ø0.4mm Max. 500mø0.5mm Max. 720mø0.6mm Max. 830m

Condition-4

ParallelConnection !

No!No!


Confidential 15

- 4ch IPGW Card

- G729a/G723.1/G711

- T.38 (FAX) mode is not supported (FAX = G711)

- Physical I/F: 10/100 Base-T

- Web programming (English)

- Interoperability with TDA0480:

Incoming call, Outgoing call and CLIP only.

- Interoperability with another manufacturers :

Not guaranteed.

1st Time Setup Connection

TDA100/200

TDA0484

10/100 Base-T Cross Cable

(http://192.168.1.200)

Pattern 1

TDA100/200

TDA0484

10/100 Base-T Straight Cable

Switching HUB

(http://192.168.1.200)

Pattern 2

IE5 or later

IE5 or later

General

VoIP Gateway Card (KX-TDA0484) - 1

Confidential 16


No

Proprietary

511

G.723/G.729a

T.38

16ms

Yes

Yes

Yes

Yes

No

H.323 V2

Yes (Client)

H.323 V4 Annex M1

511

G.711/G.723.1/G.729a

G.711

16ms

No

Yes

No

No

No

H.323 V2

TDA0480TDA0484/TDA3480Compatibility

DHCP

QSIG service

Max networked IPGW cards

Voice Codec

FAX Protocol

Echo canceller G.165/G.168

AGC

DTMF Tone Detection

SNMP

Event Notice by email

NAT

Signalling

New IPGW Card (Compatibility)

Confidential 17

VoIP Gateway Card (KX-TDA0484) - 3New IPGW Card (Interoperability)

TDA0480connect toTDA0480

OKOKOKOKOKOKOKOKOKOK

OK

OKOK

TDA0484/TDA3480connect to TDA0480

NoNoNoNoNoNoNoNoNoNo

OK

OKNo

TDA0484/TDA3480connect to

TDA0484/TDA3480

OKOKOKOKOKOKOKOKOKOK

OK

OKOK

Function

CLIRCOLPCOLRCNIPCNIRCONPCONRCT(Avoid tromboned)CF(Avoid tromboned)CCBS

CLIP

Making/Receiving callFAX Connection

Confidential 18

How to connect TDA0480 & TDA0484…

Outline of example

TRG2 TRG2

IP_Address: 192.168.1.200 IP_Address: 192.168.1.12

Subnet Mask:255.255.255.0Default GW: 192.168.1.1

IP_Address: 192.168.1.100

TDA0484 TDA0480

Ext.102TIE Access = 7

Ext.103TIE Access = 7

PBX Code= 81

PBX Code= 82

Switching HUB

Dial = [7]+[82]+[103] 103 of PBX82

Dial = [7]+[81]+[102] 102 of PBX81

TIE Routing TableLead : 82Remove : 0Added : noneTrunk : 02

TIE Routing TableLead : 81Remove : 0Added : noneTrunk : 02

A-low A-low


Confidential 19

TDA0484 Setting* Address Setting (IP Address of Card)

1.Programming1.1 Network Settings, General1.1.1 IP Address Setting

IP Address : 192.168.1.200Subnet Mask: 255.255.255.0Default GW : 192.168.1.1

* Handling setting for Incoming Call from IP Network1.Programming1.5 Hunt Pattern (for Incoming Group)

Hunt Group Grp1 = Port 1 & Port 2 Grp2 = noneHunt Pattern 1: Rcv Leading Digit = 81, Hunt Group = 1

Port 1 Port 2

BRI-QSIG

Incoming81102

PBX Code= 81

TDA0484

TRG

2

BRI-QSIG

TRG

2

IP Network

IP Network

Outgoing82103

* Handling setting for Outgoing Call from PBX to IP Network1.Programming1.6 DN2IP (Dialed Number to IP Address Translation)1.6.1 GW Entry1.6.2 DN2IP Entry

GW No.= 1Comment = 82 Office, TDA0480IP Address = 192.168.1.12Group No. = 0

Leading No. = 82Remaining Number of Digits = 3GW No./Group No. Selection = GWGW No./Group No. = 1

1.Programming1.4 VoIP Gateway/IP-PBX Interface Settings1.4.2 Others

G711 A-Law

* Interface between IPGW & PBX


Confidential 20

General TabIP Address : 192.168.1.12Subnet Mask : 255.255.255.0Rout Address 1: 192.168.1.1Rout Address 2: none

Trunk Data TabPort1 Trunk Group #1 Interface type = Basic Interface Length of call reference = 1Port2 --- same as Port1Configuration = QSIG

Hunt pattern Tab --- Incoming call Handling

Destination Number = 82Hunt pattern = 1

Trunk priority Tab

Hunt pattern 1: Priority1 = Trunk group#1 (Default)

Other TabA-law/m-law flag = A-law

DNS EditingTerminal = 81Remaining digits = 3Selected unit = TDA0484 Unit ICON

TDA0480 Setting

Configuration procedure 1. Configure TDA0480 own setting

2. Create “Other Unit” --- TDA0484 IP Address

3. Edit DNS table and send to TDA0480

4. Reset PBX after sending all data for TDA0480


Confidential 21

GW Grouping (Slide Call feature)In the case that TDA has more than an IP-GW, you can group these IP-GWs.

ＩＰ Network

Grouping

Benefit of the GW Grouping : Slide Call In the case that the IP-GW(a) is not

available because all channels are in use for example, originating IP-GW try the IP-GW(b).

ＩＰ Network

Not available

Originating IP-GW

IP-GW(b).

IP-GW(a).


Confidential 22

TDA0141&TDA0142 total

Max.32 CS / TDA200

Max.16 CS / TDA100

4 PU / CS

- Two Voice Paths per CS.- A specific CS I/F card is not needed.- A port on DHLC and DLC cards can used as the interface for KX-TDA0141.- Max. number of CS: TDA100=16 TDA200=32 (Including TDA0142).- DHLC/DLC cards software must be 2.005 or later.- Functionality : The same as TDA0142- Hand-over TDA0141 TDA0142: “YES” - Power factor is 4.

- CS Port assignment is not needed.

The TDA automatically detects the connected CS (as same as DPT connection).

DHLC

DLC

TDA0141TDA0144

TDA0143

TDA0142

ø0.4mm 222mø0.5mm 347m (CAT5)ø0.6mm 500m

2ch Cell Station (KX-TDA0141) -1

Confidential 23

How to update the CS software

1- Set a CS port to “OUS” 2- Go to “SD Card File View and Load”3- Select “PDCSDECT” (or “PDCS24G”)4- Click “Detail”

5- Take the same procedure of Ver.1.0

2ch Cell Station (KX-TDA0141) -2

Confidential 24

Function – Making Calls

- Broadcasting

- Dialing Plan

- Ext. CLIP sending on Emergency Call

- Short Cut Access to System Speed Dial

Confidential 25

211

212

213

214

215

FWD to somewhere

The caller receives C.Tone for each

time.

No RingNo Ring

An PT user (Owner) can make one way path call (= announce) to 31 parties simultaneously.After one of called party answering, the owner can begin announcement.This feature requires MEC(Memory Expansion Card : KX-TDA0105).

Configuration

211212213214215

- Wired Extension- PS-Other PBX’s Extension (Only Closed Numbering)*- Outside Telephone Number **: Only available when the networking type of the trunk is assigned as private.

* Up to 32 digits

[1][*32]+

Announce

C.Tone

C.Tone

C.Tone

One Way Path

Max.31 members

8 Groups / System

If no member answer, I cancel broadcasting and send busy tonebusy tone to the

caller.

2.System - 4.Timers & Counters - 2.DISA/DPH/CONF/T.Reminder"Answer Waiting Timer for Broadcasting Group (s)" = 0 - 120

Because of DND / PS in XDP ParallelRestriction from TRS/Barring / Call Charge Limit

Operation

Off-Hook

Off-Hook

Off-HookOverride

FWD setting

In case of No Answer, it will be disconnected by

timer.

COS:“Broadcasting Operation”

= Enable Owner

PT onlyPT only

Broadcasting - 1

Confidential 26

Announce 211Member-01

212Member-02

213Member-03

214Member-04

215Member-05

Joining Order1st --- 2nd ---3rd ---

201The owner

Conversation during broadcasting1.To let members join to conversation

2.To let members leave from conversation

(1) The Owner pushed [DSS - 212] => Ext.212 join to conference

(2) The Owner pushed [Conf.] => Youngest Member (=Ext.211) join to conference

(3) Listening Member pushed [DSS - 201] or Recall/Hookswitch=> Notification Tone goes to the owner, Member’s information appear on the Owner’s LCD.

=> The Owner push [DSS - 214] => Ext.214 join to conference

NotificationTone

LCD:Ext.214 wants conversation !

Ext.212 --- By (1)Ext.211 --- By (2)Ext.214 --- By (3)

(1)

(2)

(3)

Push [DSS-211]Push [Transfer]Push [Flash/Recall]

In above situation, when the owner does following action…

Ext.211 goes back to be a listenerLast joined member (=Ext.214) goes back to be a listenerLast joined member (=Ext.214) is disconnected from broadcasting.

Conversation with the Owner

= Max.3 MembersMax.3 Members( 4 ( 4 Party Conference )Party Conference )

Broadcasting - 2

Confidential 27

Broadcasting - 3

From an owner Extension, Dial *32 + Broadcasting group number

When a member of the group answers the call.

Conference : 2 ConferenceNo of member

LCD Display in typical conditionIn establishing

Owner Extension Called Extension

Conference1: PCCUKConference1: PCCUK

Owner Extension Called Extension

In broadcasting

Name of Broadcasting Group

Confidential 28

Broadcasting - 4Additional information

Internal Call Block is Block

Set to Call FWD

Set to DND

Busy

Auto Answer

Wireless XDP PS

Condition of Member Ext. Response for Arriving Broadcasting Call

The broadcast call arrives this extension.

The broadcast call does not arrive this extension.

Call Waiting function will be performed.

The Auto Answer function will not be performed.

The broadcast call does not arrive this PS.

The broadcast call does not arrive this extension.

Conditions and Responses of Member Extension

If owner extension has DSS key of a member of broadcasting group and establishes a broadcasting call, the DSS key does not flash when the called extension rings.It actually turns red (not flashing).

DSS key of Owner Extension which relates with member extension

Confidential 29

Dialing Plan Table for each TRG

(Table1 – Table4)

Max.32 digits

4 Tables independently

1: N112: NXXXXXX3: 1NXXNXXXXXX

1: N112: NNXXXXX3: 1NPXNXXXXXX

1: N112: NXXXXXX3: 1NNXXXXX4: 1NPXNXXXXXX

1: N112: NXXNXXXXXX3: 1NXXNXXXXXX

48: N1149: NXXXXXX50: 1NXXNXXXXXX

Type-A

Type-B

Type-C

Type-D

Type-E

N = 2-9P = 0,1X = 0-9,*,#

Max.50 leading numbers

Voice Path Tx: Mute Rx: OK

( during Dialing ) PBX recognizes the end of dialing!

Voice Path Tx: OK Rx: OK

Voice Path Tx: OK Rx: OK

( Start of Dialing )

( End of Dialing )

Dialing Planis working

Dialing Planis not working

Inter Digit Timer expired !

Making a Call with Analog CO

Inter Digit Timer

1-15s

1-15s

- PBX can know the end of dialing by Dialing Plan Table.

- It works for ISDN Enblock dial mode and Analog CO.

- Typical configuration by “Auto Assign”. (Type A/B/C/D/E)- Dialing Plan Table is assigned for each TRG.

- PBX sends all of the dialed digits at once after all digits dialed.

Dialing Plan

Confidential 30

It overrides CLIR / CO Line CLIP.Ext.CLIP is sent to PRI public network as “Location Identification Number”,even if CLIR is set or CLIP mode is “CO Line CLIP”.

-This feature works only for Emergency call.- “E911 service” must be enabled.

Yes

Ext. CLIP sending on Emergency Call

Confidential 31

[Auto] + [JOG] or [Navi-Down/UP] works as short cut key. --- TDA30 V1.0 too

- TDA100/200 Ver.1.0

“AUTO DIAL”

Nothing Happens

- TDA100/200 Ver.1.1 (TDA30 Ver.1.0)

“AUTO DIAL”System Directory

Name ?>

“” or “” Allen, DavidAllen, SteveAzure, Alf

“ENTER” Daly, GillDarcy, NigelDavies, Allan

Short Cut Access to System Speed Dial

Confidential 32

Function – Receiving Calls

- Modified DDI Number is displayed on LCD

- Disable DSS Flash

Confidential 33

- TDA100/200 Ver.1.0

- TDA100/200 Ver.1.1

ISDN4772111 (CLIP)Line 001:201 (DDI)

Caller 4772111 Ext. 201:DDI 654201

654201 201

4772111 (CLIP)Line 001:654201 (DDI)

DDI TableDIL Table & Port setting

ISDN

Ext. 201:DDI 654201

201654201

Caller 4772111

Modified DDI Number is displayed on LCD

Confidential 34

- TDA100/200 Ver.1.0

Ext. 201

External Call to Extension directly

The DSS LED on Ext.202 is flashing.The call can be picked up by pressing the button.

- TDA100/200 Ver.1.1Two options:- The DSS LED on Ext.202 will flash. The call can be picked up by pressing the button. - The DSS LED on Ext.202 will turn ON. The call cannot be picked up by pressing the button.

Busy tone is sent if the DSS button is pressed.

External Call

New program item

Enable : DSS LED will flash

Disable : DSS LED will turn ON

All DSS LED’s flashing look like a Xmas tree. Annoying!!!

Ext. 202

201

Improved DSS LED flashing/Pick up call -1

Confidential 35

- TDA100/200 Ver.1.0

External Call to ICD-Group directly

The DSS LED on Ext.202 flashes.The call can be picked up by pressing the button.

- TDA100/200 Ver.1.1Two options:- The DSS LED on Ext.202 will flash. The call can be picked up by pressing the button. - The DSS LED on Ext.202 will turn ON. The call cannot be picked up by pressing the button.

Busy tone is sent if the DSS button is pressed.

New item

Enable : DSS LED will flash

Disable : DSS LED will turn ON

Ext. 201 Ext. 202

201External Call

ICD-G 280


Confidential 36

It is possible to disable DSS LED’s turning off for an incoming call.

New itemON or Flash : DSS LED turns ON or flashes for an incoming call. OFF : DSS LED never turns ON nor flashes for an incoming call.

If the DSS button is pressed when extension is ringing,

Busy Tone

LED : ON

It is possible to pick up call

LED: Flashing

Call pick up by DSS key = Disable

Call pick up by DSS key = Enable

DSS Key mode = ON

DSS Key mode = OFF Call arrives at extension

LED: OFF


Confidential 37

Function – Hold/FWD/TR

- Disable Hold Recall

- Disable re-count Ext-CO Duration Limitation

Confidential 38

Disable Hold Recall is available if Hold Recall Timer is 0.

1-240: Hold Recall works0 : does not work V1.0 does not have.

Disable Hold Recall

Confidential 39

Disable re-count Ext-CO Duration Limitation by Hold Retrieve

Extn-CODuration Timer

Calling Party Called Party

Call dest. Party

Place on Hold

Hold Retrive

Answer

Ringing(Establishing a Call)

(In Conversation)

(On Hold to transfer)

(In Conversation)

Tim

e fl

ow Start

ReStart

StartV1.0 V1.1

- Ext 201 makes an external call. - Extension-CO duration timer on Ext 201 starts when the external party answers the call.- Ext 201 transfers the call to Ext 202.

Extension-CO duration timer on Ext 202 re-starts when Ext 202 answers the call.

Extension-CO duration timer on Ext 201 continues on Ext 202.

V1.0

V1.1

Concrete example

Disable Re-counting Ext-CO Duration Timer

Confidential 40

Function – Conference

- ISDN – 3 party Conference

- DTMF Tone through a Conference from PT

Confidential 41

2nd Party

1st Party

Adding a Third Party during a conversation using an ISDNservice (Three-party Conference [3PTY] via ISDN)

Standard : ETS 300 188

New

ISDN

It is not service item for Euro-ISDN

ISDN – 3 Party Conference (EURO-ISDN) -1

Confidential 42

How to establish a conference (During a conversation)

Press ISDN-Hold

ISDN-Hold

Dial desired phone

number

Talk to the new party

3-party conference

Press CONF

Dial desired phone

number

Talk to the new party

3-party conference

Press Transfer

Press Transfer

PT/PS

PT/PS

Enter

Enter

ISDN – 3 Party Conference (EURO-ISDN) -2

Confidential 43

- This will be useful for two parties to listen to VM message.

SLTSLT

Voice MailVoice Mail

PTPT

( Conference )

DTMFTone

DTMFTone

Not only SLT user but also PT usercan control Voice Mail.

Voice Mail control during conference call.

SLT

PT

YES(Can send DTMF)

NO(Cannot send DTMF)

YES(Can send DTMF)

YES(Can send DTMF)

V1.0 V1.1

DTMF Tone Through to Conf.Call from PT

Confidential 44

Function – Timer

- Intercept Timer for each time mode

Confidential 45

Intercept timer and DISA intercept timer can be programmed for each time service mode.

Intercept Timer for Day / Lunch / Break / Night

Intercept Timer

DISA Intercept Timer

1-60 s : Enable0 s : Disable

1-240 s

Intercept Timer For Each Time Mode

Confidential 46

Function – Others

- SMDR RC/AN Information Output

- Paging to Another Paging Group

Confidential 47

RC (Receive Call) information, it will be output when TDA receives incoming call.

AN (Answer Call) information, it will be output when extension user answered incoming call.

* SMDR Type format is not changed from V1.0 (Type A / B / C).

* KX-TD SMDR based application can work.

* But some of them can not work properly. Because the detailed Spec. and timing to output is not same as KX-TD series.

Programming is needed.

-No Print (Default)-Print

SMDR RC/AN Information Output -1

Confidential 48

Output Samples-1

20/02/04 07:48AM 201 01 203 RC20/02/04 07:49AM 201 01 203 0'56 00:00'00 NA

- External Call Extension (201) No answer Caller disconnects

20/02/04 08:22AM 201 01 203 RC20/02/04 08:22AM 201 01 203 0'11 AN Ext. 201 Answers 20/02/04 08:22AM 201 01 203 0'11 00:00'17

- External Call Extension (201) Answers Disconnects

- External Call DISA (270) OGM is sent No Answers Caller disconnects 20/02/04 09:00AM 270 01 203 RC20/02/04 09:00AM 270 01 203 0'05 AN DISA Answers 20/02/04 09:01AM 270 01 203 0'05 00:00'19 D0

20/02/04 09:04AM 270 01 203 RC20/02/04 09:04AM 270 01 203 0'05 AN DISA Answers20/02/04 09:05AM 270 01 203 0'05 00:00'09 D0 Ext. 201 Answers 20/02/04 09:05AM 201 01 203 0'00 00:00'12 TR

- External Call DISA (270) OGM is sent Ext. 201 answers Disconnects

Output Samples-2 (DISA)

Confidential 49

- External Call ICD-G (280) Time table is not started No Answers Caller disconnects Output Samples-3 (ICD-G)

20/02/04 08:42AM 280 01 203 RC20/02/04 08:42AM 280 01 203 0'05 00:00'00 NA

20/02/04 08:36AM 280 01 203 RC20/02/04 08:37AM 280 01 203 0'10 AN Time table starts 20/02/04 08:37AM 280 01 203 0'10 00:00'19

-External Call ICD-G (280) Wait Time table starts No Answers Caller disconnects

- External Call ICD-G (280) Time table is not started Ext.201 Answers Disconnect

20/02/04 08:49AM 280 01 203 RC20/02/04 08:49AM 280 01 203 0'04 AN Ext. 201 Answers 20/02/04 08:49AM 280 01 203 0'04 00:00'0020/02/04 08:49AM 201 01 203 0'00 00:00'06

-External Call ICD-G (280) Wait Time table starts Ext.201 Answers Disconnect

20/02/04 10:48PM 280 01 203 RC20/02/04 10:48PM 280 01 203 0'05 AN Time table starts20/02/04 10:48PM 280 01 203 0'05 00:00'12 Ext.201 Answers 20/02/04 10:48PM 201 01 203 0'00 00:00'06

- External Call ICD-G (280) Time table starts No Answers Caller disconnects

20/02/04 10:57PM 280 01 203 RC20/02/04 10:57PM 280 01 203 0'00 AN Time table starts 20/02/04 10:57PM 280 01 203 0'00 00:00'17

Confidential 50

- No additional programming steps are required.

- Operation is not changed from V1.0. ( [*33]+[PageG.Number(2digits)] )

- TDA100/200 Ver.1.0

Ext. 201

User Group-01

Ext. 202

User Group-02

Paging Group-01

Ext. 203

User Group-03

Ext. 204

User Group-04

Paging Group-02

NO

NOYES YES

- TDA100/200 Ver.1.1

Ext. 201

User Group-01

Ext. 202

User Group-02

Paging Group-01

Ext. 203

User Group-03

Ext. 204

User Group-04

Paging Group-02

YES

YES

YES YES

Paging to Another Paging Group

Confidential 51

Function – Programming

- Programmable COS Name & CS Name

- Ext. CLIP Automatic Generating

- DDI/DID Name Automatic Generating

- Wireless XDP Programming from PC

Confidential 52

- TDA100/200 Ver.1.0 - TDA100/200 Ver.1.1COS name

CS name

Both 20 Characters

Programmable COS Name & CS Name

Confidential 53

CLIP: 345 01 55345

55

1

201

2001Delete digit

345015534502553450355

Increase this number

New function

=> Delete from left

0- 4 1 - 999

Max. 16 digits,( 0 – 9 * # )

Max. 16 digits,( 0 – 9 * # )

Ext. CLIP Automatic Generating

Confidential 54

PCC00-UKPCC

-UK

3

1

2000

12300123011230212303

Delete digit

Increase thisnumber

PCC00-UKPCC01-UKPCC02-UKPCC03-UK

New function

1 - 1000

1 - 1000

0 - 32

Max. 20 characters

Max. 20 characters

=> Delete from left

DDI/DID Name Automatic Generating

Confidential 55

It is possible to program Wireless XDP connection from the PC maintenance console.

- Assign Wireless XDP PS number.

- Click “Apply”

- Power off-on the Wireless XDP PS for enabling this programming.

Wireless XDP Programming from PC

Confidential 56

Improvement

- Logical Check

- PS Hand-over during Conference Call

- Walking Extension from Fault Extension

Confidential 57

1. System - System Operator PBX-Operator2. Feature - Tenant Operator3. Groups - Incoming Call Distribution Group - Group Setting Supervisor

Extension4. Groups - Incoming Call Distribution Group - Member Extension No.5. Groups - Idle Extension Hunting Group Member Extension6. Groups - Voice (DTMF) Group - Group Information Extension Number of

the SLT Port Connected to VM

7. Extension - Wired Extension/Portable Station - Extension Settings Transfer Recall Destination

8. Optional Device - DISA - Message Setting 1 Digit AA Destination

9. Feature - Speed Dial & Caller ID - Main Table CLI Destination10. CO & Incoming Call - DIL Table & Port Setting DIL Destination11. CO & Incoming Call - DDI/DID Table DDI/DID Destination12. CO & Incoming Call - MSN Table MSN Destination13. Maintenance - Miscellaneous Local Alarm Display

Extension

The following extension assignment logical check function is deleted from the V1.1 PC-Soft.

In programming an extension number that does not exist, the system will now accept.

Logical Check -1

Confidential 58

What happens?

- TDA100/200 Ver.1.0

- TDA100/200 Ver.1.1

1- Open the PC maintenance tool and go to 2.System Operator then 2. PBX Operator

2- Click “Apply”

1- Open the PC maintenance2- Go to 2.System Operator 2. PBX Operator3- Click “Apply”

Dealer does not know what is wrong!

Nothing happens.

Please remember, when programming extension numbers that do not exist, that the system will now accept the entry.

Logical Check -2

Confidential 59

If we program a non-existing number ??1. PBX-Operator OUS mode Extension.2. Tenant Operator OUS mode Extension.3. Supervisor Extension No Supervisor Extension4. ICD Group Member The TDA skips this extension.5. Idle Extension Hunting Group Member The TDA skips this extension.6. VM (DTMF) Group VM function does not work.7. Transfer Recall Destination The transfer recall goes back to

the transferring Extension.8. 1 Digit AA Destination The TDA sends the re-order tone.9. CLI/DIL/DDI/DID/MSN Destination The TDA checks the following…

10. Local Alarm Display Extension No Alarm Extension.

- Re-order tone

- Re-routed to operator

Logical Check -3

Confidential 60

Handover can be made during Conference Call.

- Both of 2.4GHz model and DECT model- No programming required

PS Hand-over during Conference Call

Confidential 61

A “Fault” extension card can be used for walking extensions.

Insert and remove a card, the non connected extensions can be used for walking extensions.DHLC-8 24 extensionsSLC-8 8 extensionsDLC-8/SLC16 16 extensionsDLC-16 32 extensions

Walking Extension from Fault Extension -1

Confidential 62

Ext 201

Ext 233 Part-time worker - A 8:00-12:00Ext 234 Part-time worker - B 12:00-16:00Ext 235 Part-time worker - C 16:00-20:00Ext 236 Part-time worker - D 20:00-8:00

One existing extension can be shared to several users with different extension number.What is benefit ?

What is Walking Extension access code? *727 + Extension number + PIN

Walking Extension from Fault Extension -2

Confidential 63

To Start TDA100/200 V1.1

- PC Maintenance Console Compatibility

- Data Conversion

- Upgrade PBX

Confidential 64

TDA100/200 Ver.1.1 PC maintenance console can maintain TDA100/200 Ver.1.0 PBX, too.

Initial screen When we access TDA100/200 Ver.1.0

Automatically

PC Maintenance Console Compatibility

Confidential 65

Data Conversion

DSYS-1.1

PC maintenance console provides a data convert function. (DSYS Ver.1.0 to DSYS Ver.1.1)

1- Open the PC Maintenance console and open the saved DSYS (Ver 1.0).

DSYS 1.0

3- Enter new file name and click “Save”

2- Click

DSYS 1.1

Confidential 66

Upgrade PBX1. Prepare following files

- PMPR 1.1, DLNG0 1.1, DLNG1 1.1- DSYS 1.1 --- Converted DSYS or New DSYS created by PC-Soft

2. Download above files to PBX

3. Reset PBX by command- V1.0054 or later --- Please select PMPR_SUB, DSYS_SUB, then reset- Before V1.0054 --- Please reset without any care.

Select

Select

4.Connect PC-Soft again and download other files as PC-Soft’s dialog box saying.

5.If PC-Soft require reset, reset PBX again, then you can finish upgrading.

Confidential 67

Thank you very much !Thank you very much !

Confidential1 Panasonic Communications Co., Ltd. Network Business Company Edition 1.3 07 Jul., 2004...

Documents

Transcript of Confidential1 Panasonic Communications Co., Ltd. Network Business Company Edition 1.3 07 Jul., 2004...