Composite mirror suspensions development status
description
Transcript of Composite mirror suspensions development status
![Page 1: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/1.jpg)
Composite mirror suspensionsdevelopment status
Riccardo DeSalvo For the ELiTES R&D group WP1 & 2
JGW-G1201174
![Page 2: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/2.jpg)
The idea
• A fresh approach to the design of low thermal noise mirror suspensions
for KAGRA and ET
![Page 3: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/3.jpg)
Key features:
• Composite structure• Purely Compressive
joints• No shear noise• No need for bonding• Easy replacements• Easily scalable to larger
masses
![Page 4: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/4.jpg)
Flexure Key features:
• Silicon flexures • Intrinsic Q-factor >108
• Thermo-elastic >106
• Diluted Q-factor >109
• Before cryo gain !
• Many Machining options available
![Page 5: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/5.jpg)
Flexure structure
• Ultra-Sound Machined structure
• Etching of the flexure surface
• Expected to increase the break point >1GPa
![Page 6: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/6.jpg)
Flexure structure
• Thin, short, etched flexure
• smallflexure aspect ratio
• Large thermal conductance
![Page 7: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/7.jpg)
Chao Shiu laboratory, TaiwanSilicon cantilever with KOH wet etching
4” un-doped double-side polished (001) silicon wafer, 500um thickness etched down to 92 and 52 µm
0.3 10-6 loss measured from residual gas
44.35 mm
10 mm
92 μm or 52 μm
34 mm 0.35mm500 μm
5.5mm
Frequency=59.04 (Hz)
φmeasurement = 1.4*10-6
Time(sec)
Ampl
itude
Decay Time = 3940.8 (s)
Silicon cantilever (d=52um)
Ampl
itude
(V)
Original Data
Decay Time = 710.1 (s) φmeasurement = 4.3*10-6
Frequency = 103.20 (Hz)
Silicon cantilever (d=92um)
![Page 8: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/8.jpg)
Thermo-elastic limit
• @ 59 Hz 0.945 10-6 loss angle predicted (T.E.)• 1.3 10-6 measured (-) 0.3 10-6 residual gas• 1. 10-6 loss angle measured• => 100% Thermoelastic limited ! ! !
Frequency=59.04 (Hz)
φmeasurement = 1.4*10-6
Time(sec)
Ampl
itude
Decay Time = 3940.8 (s)
Silicon cantilever (d=52um)
![Page 9: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/9.jpg)
Kenji’s Q-factor measurements
• Measurement on a mirror substrate
• 108 lower limit
![Page 10: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/10.jpg)
Ribbons Key features:
• Compression joint attachment
• Machined-polished Sapphire ribbons
(from bulk, not grown)• High quality sapphire• High quality surface finish
(sub-phonon defect size) • = > High thermal
conductivity !
![Page 11: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/11.jpg)
Conductance budget
• Preliminary conductance budget from Sakakibara with 1 W load
• Thin ribbon responsible for bulk of loss ! ! !
• Plenty of space for parametric optimization
![Page 12: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/12.jpg)
Mirror attachment Key features:
• Mini-alcoves (low volume machining)
• Machining before coating deposition
• Minimize substrate induced stress
• Recessed attachment, Low vulnerability
• No bonding shear noise• No flats, 100% of mirror
surfaceavailable
![Page 13: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/13.jpg)
ConnectionsKey features:
• Purely compressive joints
• Sub-m, Gallium gaskets + direct contact
• Complete elimination of stick and slip noise
• Perfect heat conductivity• Easy replaceability
![Page 14: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/14.jpg)
• Silicon springs• Defects etched away• Allowable surface
stress < 1 GPa (to be confirmed)
• Elimination of vertical suspension thermal noise (necessary due to KAGRA’s tunnel tilt)
Springs Key features:
![Page 15: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/15.jpg)
NIKHEF test
• Produce a number od samples• Test and see
![Page 16: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/16.jpg)
Etched Silicon cantilever blades
• Etch the bending area• Leave thick section for
clamping and for fiber connection
• With 0.15 Gpa Only limited flexure possible
• With >1GPa large deflection
![Page 17: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/17.jpg)
Larger stresses possible?
• MEM sensors operating at 1.4 GPa, ~ 10 times higher limit!
• Is etching eliminating surface defect and therefore causing the larger strength?
• if YES, large bends possible!
• Lower frequency bounce modes
![Page 18: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/18.jpg)
Key technologies:
• Ultrasound machining of sapphire and silicon
• Magneto-rheological Finishing (QED)
• Silicon etching to eliminate defects
![Page 19: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/19.jpg)
Why Gallium
• Indium proved extremely effective to eliminate friction noise in compression joints (Vladimir Braginsky)
• Melts at relatively high temperature• May need heating mirror to more than 160oC
for disassembly
![Page 20: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/20.jpg)
Indium vs. Gallium
![Page 21: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/21.jpg)
Violin mode elimination• Fiber-fed Red-shifted Fabry-Perot• Can cool violin modesand bounce
modes to mK level(Same for Parametric
Instabilities ?)
![Page 22: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/22.jpg)
Opportunities
• Once eliminated violin and bounce resonance peaks there is
• no more disadvantage in having heavier non c-axis, ETMs different from ITMs
![Page 23: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/23.jpg)
Opportunities
• Composite suspensions • offer several possibilities for thesis to • attract several new PhD students
![Page 24: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/24.jpg)
What was done
• Discussed Ultra-Sound Machining technology capabilities and limitation with Mack
• Interactively advanced design • Optimized machining procedures to physics
requirements• Design optimization ongoing
![Page 25: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/25.jpg)
To do list • FE simulation• GWINC simulations• Test machining• Test assembly• Thermal Conductivity• Q-factors• Gallium• . . . . .
• Test effective break point– Etched not etched– doped-not doped– Different axis orientation– tension
![Page 26: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/26.jpg)
Thermal conductivity measurements
• Karen Martirosyan will perform at UTB in a PPMS-TTO temperature scanning cryostat
• (End of the year)
![Page 27: Composite mirror suspensions development status](https://reader031.fdocuments.in/reader031/viewer/2022020423/56813d65550346895da73f5b/html5/thumbnails/27.jpg)
Development target• Going from strawman to final design of cryo
suspensions for KAGRA mirrors• NIKHEF volunteered to lead, provide most of parts for
this R&D stage, and perform tests• Alessandro Bertolini co-ordinating this R&D• But many other contributions are needed– Fracture measurements (NIKHEF)– Q-measurements (TsingHua-Taiwan, EGO facility)– Thermal measurements (UTB) – FEM simulations (Roma, . .) . . .