Introduction to Composite Materials Introduction to Composite ...
Composite Materials
-
Upload
pradeepkumar-chikkamath -
Category
Documents
-
view
29 -
download
2
description
Transcript of Composite Materials
Composite Materials
R Lindeke
ENGR 2110
Introduction
bull A Composite material is a material system composed of
two or more macro constituents that differ in shape and
chemical composition and which are insoluble in each
other The history of composite materials dates back to
early 20th century In 1940 fiber glass was first used to
reinforce epoxy
bull Applications
ndash Aerospace industry
ndash Sporting Goods Industry
ndash Automotive Industry
ndash Home Appliance Industry
Advanced Aerospace Application
Lear Fan 2100 ldquoall-compositerdquo aircraft
Advanced Aerospace Application
Boeing 767 (and in 777 787 airplanes w the latest full wing box is composite)
bull Composites-- Multiphase material wsignificant
proportions of each phase
bull Dispersed phase-- Purpose enhance matrix properties
MMC increase sy TS creep resist
CMC increase Kc
PMC increase E sy TS creep resist
-- Classification Particle fiber structural
bull Matrix-- The continuous phase
-- Purpose is to- transfer stress to other phases
- protect phases from environment
-- Classification MMC CMC PMC
metal ceramic polymer
Reprinted with permission from
D Hull and TW Clyne An
Introduction to Composite Materials
2nd ed Cambridge University Press
New York 1996 Fig 36 p 47
TerminologyClassification
woven fibers
cross section view
05mm
05mm
Composite Structural Organization the
design variations
Composite Survey
Large-
particle
Dispersion-
strengthened
Particle-reinforced
Continuous
(aligned)
Aligned Randomly
oriented
Discontinuous
(short)
Fiber-reinforced
Laminates Sandwich
panels
Structural
Composites
Adapted from Fig
162 Callister 7e
bull CMCs Increased toughness
Composite Benefits
fiber-reinf
un-reinf
particle-reinfForce
Bend displacement
bull PMCs Increased Er
E(GPa)
G=3E8K=E
Density r [mgm3]1 3 1 3 10 30
01
1
1
10
102
103
metal metal alloys
polymers
PMCs
ceramics
Adapted from TG Nieh Creep rupture of a
silicon-carbide reinforced aluminum
composite Metall Trans A Vol 15(1) pp
139-146 1984 Used with permission
bull MMCsIncreased
creep
resistance
20 30 50 100 20010
-10
10-8
10-6
10-4
6061 Al
6061 Al wSiC whiskers s(MPa)
ess (s-1)
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Introduction
bull A Composite material is a material system composed of
two or more macro constituents that differ in shape and
chemical composition and which are insoluble in each
other The history of composite materials dates back to
early 20th century In 1940 fiber glass was first used to
reinforce epoxy
bull Applications
ndash Aerospace industry
ndash Sporting Goods Industry
ndash Automotive Industry
ndash Home Appliance Industry
Advanced Aerospace Application
Lear Fan 2100 ldquoall-compositerdquo aircraft
Advanced Aerospace Application
Boeing 767 (and in 777 787 airplanes w the latest full wing box is composite)
bull Composites-- Multiphase material wsignificant
proportions of each phase
bull Dispersed phase-- Purpose enhance matrix properties
MMC increase sy TS creep resist
CMC increase Kc
PMC increase E sy TS creep resist
-- Classification Particle fiber structural
bull Matrix-- The continuous phase
-- Purpose is to- transfer stress to other phases
- protect phases from environment
-- Classification MMC CMC PMC
metal ceramic polymer
Reprinted with permission from
D Hull and TW Clyne An
Introduction to Composite Materials
2nd ed Cambridge University Press
New York 1996 Fig 36 p 47
TerminologyClassification
woven fibers
cross section view
05mm
05mm
Composite Structural Organization the
design variations
Composite Survey
Large-
particle
Dispersion-
strengthened
Particle-reinforced
Continuous
(aligned)
Aligned Randomly
oriented
Discontinuous
(short)
Fiber-reinforced
Laminates Sandwich
panels
Structural
Composites
Adapted from Fig
162 Callister 7e
bull CMCs Increased toughness
Composite Benefits
fiber-reinf
un-reinf
particle-reinfForce
Bend displacement
bull PMCs Increased Er
E(GPa)
G=3E8K=E
Density r [mgm3]1 3 1 3 10 30
01
1
1
10
102
103
metal metal alloys
polymers
PMCs
ceramics
Adapted from TG Nieh Creep rupture of a
silicon-carbide reinforced aluminum
composite Metall Trans A Vol 15(1) pp
139-146 1984 Used with permission
bull MMCsIncreased
creep
resistance
20 30 50 100 20010
-10
10-8
10-6
10-4
6061 Al
6061 Al wSiC whiskers s(MPa)
ess (s-1)
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Advanced Aerospace Application
Lear Fan 2100 ldquoall-compositerdquo aircraft
Advanced Aerospace Application
Boeing 767 (and in 777 787 airplanes w the latest full wing box is composite)
bull Composites-- Multiphase material wsignificant
proportions of each phase
bull Dispersed phase-- Purpose enhance matrix properties
MMC increase sy TS creep resist
CMC increase Kc
PMC increase E sy TS creep resist
-- Classification Particle fiber structural
bull Matrix-- The continuous phase
-- Purpose is to- transfer stress to other phases
- protect phases from environment
-- Classification MMC CMC PMC
metal ceramic polymer
Reprinted with permission from
D Hull and TW Clyne An
Introduction to Composite Materials
2nd ed Cambridge University Press
New York 1996 Fig 36 p 47
TerminologyClassification
woven fibers
cross section view
05mm
05mm
Composite Structural Organization the
design variations
Composite Survey
Large-
particle
Dispersion-
strengthened
Particle-reinforced
Continuous
(aligned)
Aligned Randomly
oriented
Discontinuous
(short)
Fiber-reinforced
Laminates Sandwich
panels
Structural
Composites
Adapted from Fig
162 Callister 7e
bull CMCs Increased toughness
Composite Benefits
fiber-reinf
un-reinf
particle-reinfForce
Bend displacement
bull PMCs Increased Er
E(GPa)
G=3E8K=E
Density r [mgm3]1 3 1 3 10 30
01
1
1
10
102
103
metal metal alloys
polymers
PMCs
ceramics
Adapted from TG Nieh Creep rupture of a
silicon-carbide reinforced aluminum
composite Metall Trans A Vol 15(1) pp
139-146 1984 Used with permission
bull MMCsIncreased
creep
resistance
20 30 50 100 20010
-10
10-8
10-6
10-4
6061 Al
6061 Al wSiC whiskers s(MPa)
ess (s-1)
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Advanced Aerospace Application
Boeing 767 (and in 777 787 airplanes w the latest full wing box is composite)
bull Composites-- Multiphase material wsignificant
proportions of each phase
bull Dispersed phase-- Purpose enhance matrix properties
MMC increase sy TS creep resist
CMC increase Kc
PMC increase E sy TS creep resist
-- Classification Particle fiber structural
bull Matrix-- The continuous phase
-- Purpose is to- transfer stress to other phases
- protect phases from environment
-- Classification MMC CMC PMC
metal ceramic polymer
Reprinted with permission from
D Hull and TW Clyne An
Introduction to Composite Materials
2nd ed Cambridge University Press
New York 1996 Fig 36 p 47
TerminologyClassification
woven fibers
cross section view
05mm
05mm
Composite Structural Organization the
design variations
Composite Survey
Large-
particle
Dispersion-
strengthened
Particle-reinforced
Continuous
(aligned)
Aligned Randomly
oriented
Discontinuous
(short)
Fiber-reinforced
Laminates Sandwich
panels
Structural
Composites
Adapted from Fig
162 Callister 7e
bull CMCs Increased toughness
Composite Benefits
fiber-reinf
un-reinf
particle-reinfForce
Bend displacement
bull PMCs Increased Er
E(GPa)
G=3E8K=E
Density r [mgm3]1 3 1 3 10 30
01
1
1
10
102
103
metal metal alloys
polymers
PMCs
ceramics
Adapted from TG Nieh Creep rupture of a
silicon-carbide reinforced aluminum
composite Metall Trans A Vol 15(1) pp
139-146 1984 Used with permission
bull MMCsIncreased
creep
resistance
20 30 50 100 20010
-10
10-8
10-6
10-4
6061 Al
6061 Al wSiC whiskers s(MPa)
ess (s-1)
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Composites-- Multiphase material wsignificant
proportions of each phase
bull Dispersed phase-- Purpose enhance matrix properties
MMC increase sy TS creep resist
CMC increase Kc
PMC increase E sy TS creep resist
-- Classification Particle fiber structural
bull Matrix-- The continuous phase
-- Purpose is to- transfer stress to other phases
- protect phases from environment
-- Classification MMC CMC PMC
metal ceramic polymer
Reprinted with permission from
D Hull and TW Clyne An
Introduction to Composite Materials
2nd ed Cambridge University Press
New York 1996 Fig 36 p 47
TerminologyClassification
woven fibers
cross section view
05mm
05mm
Composite Structural Organization the
design variations
Composite Survey
Large-
particle
Dispersion-
strengthened
Particle-reinforced
Continuous
(aligned)
Aligned Randomly
oriented
Discontinuous
(short)
Fiber-reinforced
Laminates Sandwich
panels
Structural
Composites
Adapted from Fig
162 Callister 7e
bull CMCs Increased toughness
Composite Benefits
fiber-reinf
un-reinf
particle-reinfForce
Bend displacement
bull PMCs Increased Er
E(GPa)
G=3E8K=E
Density r [mgm3]1 3 1 3 10 30
01
1
1
10
102
103
metal metal alloys
polymers
PMCs
ceramics
Adapted from TG Nieh Creep rupture of a
silicon-carbide reinforced aluminum
composite Metall Trans A Vol 15(1) pp
139-146 1984 Used with permission
bull MMCsIncreased
creep
resistance
20 30 50 100 20010
-10
10-8
10-6
10-4
6061 Al
6061 Al wSiC whiskers s(MPa)
ess (s-1)
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Structural Organization the
design variations
Composite Survey
Large-
particle
Dispersion-
strengthened
Particle-reinforced
Continuous
(aligned)
Aligned Randomly
oriented
Discontinuous
(short)
Fiber-reinforced
Laminates Sandwich
panels
Structural
Composites
Adapted from Fig
162 Callister 7e
bull CMCs Increased toughness
Composite Benefits
fiber-reinf
un-reinf
particle-reinfForce
Bend displacement
bull PMCs Increased Er
E(GPa)
G=3E8K=E
Density r [mgm3]1 3 1 3 10 30
01
1
1
10
102
103
metal metal alloys
polymers
PMCs
ceramics
Adapted from TG Nieh Creep rupture of a
silicon-carbide reinforced aluminum
composite Metall Trans A Vol 15(1) pp
139-146 1984 Used with permission
bull MMCsIncreased
creep
resistance
20 30 50 100 20010
-10
10-8
10-6
10-4
6061 Al
6061 Al wSiC whiskers s(MPa)
ess (s-1)
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Survey
Large-
particle
Dispersion-
strengthened
Particle-reinforced
Continuous
(aligned)
Aligned Randomly
oriented
Discontinuous
(short)
Fiber-reinforced
Laminates Sandwich
panels
Structural
Composites
Adapted from Fig
162 Callister 7e
bull CMCs Increased toughness
Composite Benefits
fiber-reinf
un-reinf
particle-reinfForce
Bend displacement
bull PMCs Increased Er
E(GPa)
G=3E8K=E
Density r [mgm3]1 3 1 3 10 30
01
1
1
10
102
103
metal metal alloys
polymers
PMCs
ceramics
Adapted from TG Nieh Creep rupture of a
silicon-carbide reinforced aluminum
composite Metall Trans A Vol 15(1) pp
139-146 1984 Used with permission
bull MMCsIncreased
creep
resistance
20 30 50 100 20010
-10
10-8
10-6
10-4
6061 Al
6061 Al wSiC whiskers s(MPa)
ess (s-1)
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull CMCs Increased toughness
Composite Benefits
fiber-reinf
un-reinf
particle-reinfForce
Bend displacement
bull PMCs Increased Er
E(GPa)
G=3E8K=E
Density r [mgm3]1 3 1 3 10 30
01
1
1
10
102
103
metal metal alloys
polymers
PMCs
ceramics
Adapted from TG Nieh Creep rupture of a
silicon-carbide reinforced aluminum
composite Metall Trans A Vol 15(1) pp
139-146 1984 Used with permission
bull MMCsIncreased
creep
resistance
20 30 50 100 20010
-10
10-8
10-6
10-4
6061 Al
6061 Al wSiC whiskers s(MPa)
ess (s-1)
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Survey Particle-I
bull ExamplesAdapted from Fig
1019 Callister 7e
(Fig 1019 is
copyright United
States Steel
Corporation 1971)
- Spheroidite
steelmatrix ferrite (a)
(ductile)
particles cementite(Fe3C)
(brittle)60 mm
Adapted from Fig
164 Callister 7e
(Fig 164 is courtesy
Carboloy Systems
Department General
Electric Company)
- WCCo
cemented
carbide
matrix cobalt (ductile)
particles WC (brittle hard)Vm
5-12 vol 600mmAdapted from Fig
165 Callister 7e
(Fig 165 is courtesy
Goodyear Tire and
Rubber Company)
- Automobile
tiresmatrix rubber (compliant)
particles C (stiffer)
075mm
Particle-reinforced Fiber-reinforced Structural
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Survey Particle-II
Concrete ndash gravel + sand + cement
- Why sand and gravel Sand packs into gravel voids
Reinforced concrete - Reinforce with steel rebar or remesh
- increases strength - even if cement matrix is cracked
Prestressed concrete - remesh under tension during setting of
concrete Tension release puts concrete under compressive force
- Concrete much stronger under compression
- Applied tension must exceed compressive force
Particle-reinforced Fiber-reinforced Structural
threaded
rodnut
Post tensioning ndash tighten nuts to put under rod under tension
but concrete under compression
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Elastic modulus Ec of composites-- two approaches
bull Application to other properties-- Electrical conductivity se Replace E in the above equations
with se
-- Thermal conductivity k Replace E in above equations with k
Adapted from Fig 163
Callister 7e (Fig 163 is
from RH Krock ASTM
Proc Vol 63 1963)
Composite Survey Particle-III
lower limit
1
Ec=
Vm
Em+
Vp
Ep
c m m
upper limit
E = V E + VpEp
ldquorule of mixturesrdquo
Particle-reinforced Fiber-reinforced Structural
Data
Cu matrix
wtungsten
particles
0 20 40 60 80 100
150
200
250
300
350
vol tungsten
E(GPa)
(Cu) (W)
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Survey Fiber
bull Fibers themselves are very strong
ndash Provide significant strength improvement to
material
ndash Ex fiber-glass
bull Continuous glass filaments in a polymer matrix
bull Strength due to fibers
bull Polymer simply holds them in place and
environmentally protects them
Particle-reinforced Fiber-reinforced Structural
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Fiber Loading Effect under Stress
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Critical fiber length (lC) for effective stiffening amp strengthening
bull Ex For fiberglass a fiber length gt 15 mm is needed since this length
provides a ldquoContinuous fiberrdquo based on usual glass fiber properties
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
c
f d
s 15length fiber
fiber diameter
shear strength of
fiber-matrix interface
fiber strength in tension
bull Why Longer fibers carry stress more efficientlyShorter thicker fiber
c
f d
s 15length fiber
Longer thinner fiber
Poorer fiber efficiency
Adapted from Fig
167 Callister 7e
c
f d
s 15length fiber
Better fiber efficiency
s(x) s(x)
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Fiber Load Behavior under Stress
l2
fc
c
ds
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Survey Fiber
bull Fiber Materialsndash Whiskers - Thin single crystals - large length to diameter ratio
bull graphite SiN SiC
bull high crystal perfection ndash extremely strong strongest known
bull very expensive
Particle-reinforced Fiber-reinforced Structural
ndash Fibers
bull polycrystalline or amorphous
bull generally polymers or ceramics
bull Ex Al2O3 Aramid E-glass Boron UHMWPE
ndash Wires
bull Metal ndash steel Mo W
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Fiber Alignment
aligned
continuous
aligned random
discontinuous
Adapted from Fig
168 Callister 7e
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Behavior under load for Fibers amp
Matrix
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Strength Longitudinal Loading
Continuous fibers - Estimate fiber-reinforced
composite strength for long continuous fibers in a
matrix
bull Longitudinal deformation
sc = smVm + sfVf but ec = em = ef
volume fraction isostrain
Ece = Em Vm + EfVf longitudinal (extensional)
modulus
mm
ff
m
f
VE
VE
F
F f = fiber
m = matrix
Remembering E = se
and note this model
corresponds to the
ldquoupper boundrdquo for
particulate composites
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Strength Transverse Loading
bull In transverse loading the fibers carry less of
the load and are in a state of lsquoisostressrsquo
sc = sm = sf = s ec= emVm + efVf
f
f
m
m
ct E
V
E
V
E
1transverse modulus
Remembering E = se
and note this model
corresponds to the ldquolower
boundrdquo for particulate
composites
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
An Example
Note (for ease of conversion)
6870 Nm2 per psi
UTS SI Modulus SI
579 MPa 38 GPa
24 GPa 3999 GPa
(2415 GPa)
(934 GPa)
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Estimate of Ec and TS for discontinuous fibers
-- valid when
-- Elastic modulus in fiber direction
-- TS in fiber direction
efficiency factor-- aligned 1D K = 1 (aligned )
-- aligned 1D K = 0 (aligned )
-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
(aligned 1D)
Values from Table 163 Callister 7e
(Source for Table 163 is H Krenchel
Fibre Reinforcement Copenhagen
Akademisk Forlag 1964)
Composite Strength
c
f d
s 15length fiber
Particle-reinforced Fiber-reinforced Structural
(TS)c = (TS)mVm + (TS)fVf
Ec = EmVm + KEfVf
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Aligned Continuous fibersbull Examples
From W Funk and E Blank ldquoCreep
deformation of Ni3Al-Mo in-situ
composites Metall Trans A Vol 19(4) pp
987-998 1988 Used with permission
-- Metal g(Ni3Al)-a(Mo)
by eutectic solidification
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
matrix a (Mo) (ductile)
fibers grsquo (Ni3Al) (brittle)
2mm
-- Ceramic Glass wSiC fibersformed by glass slurry
Eglass = 76 GPa ESiC = 400 GPa
(a)
(b)
fracture surface
From FL Matthews and RL
Rawlings Composite Materials
Engineering and Science Reprint
ed CRC Press Boca Raton FL
2000 (a) Fig 422 p 145 (photo by
J Davies) (b) Fig 1120 p 349
(micrograph by HS Kim PS
Rodgers and RD Rawlings) Used
with permission of CRC
Press Boca Raton FL
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Discontinuous random 2D fibersbull Example Carbon-Carbon
-- process fiberpitch then
burn out at up to 2500ordmC
-- uses disk brakes gas
turbine exhaust flaps nose
cones
bull Other variations-- Discontinuous random 3D
-- Discontinuous 1D
Composite Survey Fiber
Particle-reinforced Fiber-reinforced Structural
(b)
fibers lie in plane
view onto plane
C fibers very stiff very strong
C matrix less stiff less strong
(a)
efficiency factor-- random 2D K = 38 (2D isotropy)
-- random 3D K = 15 (3D isotropy)
Ec = EmVm + KEfVf
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Looking at strength
where is fiber fracture strength
amp is matrix stress when composite fails
where d is fiber diameter amp
is smaller of Matrix Fiber shea
1 12
1
f
m
C
C
Ccd f f m f
C
Ccd f m f
l l
lV V
l
l l
lV V
d
s
s
s s s
s s
r strength
or matrix shear yield strength
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Stacked and bonded fiber-reinforced sheets
-- stacking sequence eg 0ordm90ordm or 04590ordm
-- benefit balanced in-plane stiffness
Adapted from Fig
1616 Callister 7e
Composite Survey Structural
Particle-reinforced Fiber-reinforced Structural
bull Sandwich panels-- low density honeycomb core
-- benefit light weight large bending stiffness
honeycomb
adhesive layerface sheet
Adapted from Fig 1618
Callister 7e (Fig 1618 is
from Engineered Materials
Handbook Vol 1 Composites ASM International Materials Park OH 1987)
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Manufacturing
Processes
bull Particulate Methods Sintering
bull Fiber reinforced Several
bull Structural Usually Hand lay-up and atmospheric curing or vacuum curing
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
copy 2000 The McGraw-Hill Companies IncIrwinMcGraw-Hill
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Open Mold Processes
Only one mold (male or female) is needed and may be made of any
material such as wood reinforced plastic or for longer runs sheet metal
or electroformed nickel The final part is usually very smooth
Shaping Steps that may be taken for high quality
1 Mold release agent (silicone polyvinyl alcohol fluorocarbon or
sometimes plastic film) is first applied
2 Unreinforced surface layer (gel coat) may be deposited for best surface
quality
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Hand Lay-Up The resin and fiber (or pieces cut from
prepreg) are placed manually air is expelled with
squeegees and if necessary multiple layers are
built up
Hardening is at room temperature but may be improved by heating
Void volume is typically 1
Foam cores may be incorporated (and left in the part) for greater
shape complexity Thus essentially all shapes can be produced
Process is slow (deposition rate around 1 kgh) and labor-intensive
Quality is highly dependent on operator skill
Extensively used for products such as airframe components boats
truck bodies tanks swimming pools and ducts
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
A spray gun supplying resin in two converging streams into which roving
is chopped
Automation with robots results in highly reproducible production
Labor costs are lower
SPRAY-UP MOLDING
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Cut and lay the ply or prepreg under computer control and without tension
may allow reentrant shapes to be made
Cost is about half of hand lay-up
Extensively used for products such as airframe components boats truck
bodies tanks swimming pools and ducts
Tape-Laying Machines
(Automated Lay-Up)
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Filament Windingndash Ex pressure tanks
ndash Continuous filaments wound onto mandrel
Adapted from Fig 1615 Callister 7e [Fig
1615 is from N L Hancox (Editor) Fibre
Composite Hybrid Materials The Macmillan
Company New York 1981]
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Filament Winding Characteristics
۰Because of the tension reentrant shapes cannot be produced
۰CNC winding machines with several degrees of freedom (sometimes 7)
are frequently employed
۰The filament (or tape tow or band) is either precoated with the polymer
or is drawn through a polymer bath so that it picks up polymer on
its way to the winder
۰Void volume can be higher (3)
۰The cost is about half that of tape laying
۰Productivity is high (50 kgh)
۰Applications include fabrication of composite pipes tanks and pressure
vessels Carbon fiber reinforced rocket motor cases used for
Space Shuttle and other rockets are made this way
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Pultrusion
۰ Fibers are impregnate with a prepolymer exactly positioned with guides
preheated and pulled through a heated tapering die where curing
takes place
۰Emerging product is cooled and pulled by oscillating clamps
۰Small diameter products are wound up
۰Two dimensional shapes including solid rods profiles or hollow tubes
similar to those produced by extrusion are made hence its name
lsquopultrusionrsquo
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
Composite Production Methods
Pultrusionndash Continuous fibers pulled through resin tank then preforming die
amp oven to cure
Adapted from Fig
1613 Callister 7e
۰Production rates around 1 mmin
۰Applications are to sporting goods (golf club shafts) vehicle drive shafts
(because of the high damping capacity) nonconductive ladder rails for
electrical service and structural members for vehicle and aerospace
applications
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
PREPREG PRODUCTION PROCESSES
۰Prepreg is the composite industryrsquos term for continuous fiber reinforcement
pre-impregnated with a polymer resin that is only partially cured
۰Prepreg is delivered in tape form to the manufacturer who then molds and fully
cures the product without having to add any resin
۰This is the composite form most widely used for structural applications
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
۰ Manufacturing begins by collimating a series of spool-wound
continuous fiber tows
۰ Tows are then sandwiched and pressed between sheets of
release and carrier paper using heated rollers
(calendering)
۰ The release paper sheet has been coated with a thin film of
heated resin solution to provide for its thorough
impregnation of the fibers
PrePreg Process
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
۰ The final prepreg product is a thin tape consisting of
continuous and aligned fibers embedded in a
partially cured resin
۰ Prepared for packaging by winding onto a cardboard
core
۰ Typical tape thicknesses range between 008 and 025
mm
۰ Tape widths range between 25 and 1525 mm
۰ Resin content lies between about 35 and 45 vol
PrePreg Process
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
۰The prepreg is stored at 0C (32 F) or lower because thermoset matrix
undergoes curing reactions at room temperature Also the time in
use at room temperature must be minimized Life time is about 6
months if properly handled
۰Both thermoplastic and thermosetting resins are utilized carbon glass
and aramid fibers are the common reinforcements
۰Actual fabrication begins with the lay-up Normally a number of plies are
laid up to provide the desired thickness
۰The lay-up can be by hand or automated
PrePreg Process
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary
bull Composites are classified according to-- the matrix material (CMC MMC PMC)
-- the reinforcement geometry (particles fibers layers)
bull Composites enhance matrix properties-- MMC enhance sy TS creep performance
-- CMC enhance Kc
-- PMC enhance E sy TS creep performance
bull Particulate-reinforced
-- Elastic modulus can be estimated
-- Properties are isotropic
bull Fiber-reinforced
-- Elastic modulus and TS can be estimated along fiber dir
-- Properties can be isotropic or anisotropic
bull Structural-- Based on build-up of sandwiches in layered form
Summary