Combo Tray Shelf and Liquid Bin Model Instruction Leaflet CS2 Tray...Combo Tray Shelf and Liquid Bin...

COMBO INSTRUCTION LEAFLET - TRAY SHELF & LIQUID RESERVOIR MODEL NOTE: Ensure that all relevant personnel read the points listed below and that a copy is passed on to staff involved with the installation. Please also refer to the ‘Manual Handling Operations Regulations 1992’ during the handling of the product and materials used for installation. P. 1 TM OPENING AND CLOSING THE UNIT: 1. 2. 3. 4. Lift the tray shelf upwards so that it is resting against the aperture. Lift both catches on either side of the door at the same time to release it. Pull the door forwards so that it rests on the retention straps. To close, push the door inwards until the catches click into place. Pull the tray holder downwards. Hook the open sack over the steel sack band as shown above. 5. 6. Lifting the sack band slightly, hook the remaining sack over the two rubber grips located on both corners of the bin and replace the sack band to ensure a tight ﬁt. EMPTYING AND REPLACING RESERVOIRS: 7. 8. Open the door of the bin, steps 1-3. Should you need to gain better access to the reservoirs, the door can be removed by unhooking the straps (see circle above). Using two hands, slide one of the reservoirs towards you holding the handle in one hand. IMPORTANT: This may be heavy (less than 10kg) so take care when removing. After emptying the reservoirs, replace by standing them on the reservoir holder. Ensure the handles are at the front for ease of emptying and the warning stickers are facing towards the door . 9. 10. Repeat step 8 to remove the second reservoir. 11. NOTE: To clean the funnel ﬁlter caps, open the door and push the caps upwards from the inside of the bin. COMBO IS A TRADEMARK OF GLASDON GROUP AND ITS SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES. Replacement components are available direct from GLASDON. GLASDON cannot be held responsible for claims arising from incorrect installation, unauthorised modifications or misuse of the product. Issue 1 July 2013 C000/0449 © Copyright July 2013 Glasdon U.K. Ltd reserves the right to alter specifications without prior notice. Preston New Road BLACKPOOL Lancashire FY4 4UL Tel: 01253 600410 Fax: 01253 792558 E-mail: [email protected] Web: www.glasdon.com TM

Upload
others
Category

Documents
view
2
download
0

Embed Size (px):

Transcript of Combo Tray Shelf and Liquid Bin Model Instruction Leaflet CS2 Tray...Combo Tray Shelf and Liquid Bin...

COMBO INSTRUCTION LEAFLET - TRAY SHELF & LIQUID RESERVOIR MODELNOTE: Ensure that all relevant personnel read the points listed below and that a copy is passed on to staff involved

with the installation. Please also refer to the ‘Manual Handling Operations Regulations 1992’ during the handling of the product and materials used for installation.

P. 1

TM

OPENING AND CLOSING THE UNIT:

1. 2. 3. 4.

Lift the tray shelf upwards so that it is resting against the aperture.

Lift both catches on either side of the door at the same time to release it.

Pull the door forwards so that it rests on the retention straps.

To close, push the door inwards until the catches click into place. Pull the tray holder downwards.

Hook the open sack over the steel sack band as shown above.

5. 6.

Lifting the sack band slightly, hook the remaining sack over the two rubber grips located on both corners of the bin and replace the sack band to ensure a tight �t.

EMPTYING AND REPLACING RESERVOIRS:

7. 8.

Open the door of the bin, steps 1-3. Should you need to gain better access to the reservoirs, the door can be removed by unhooking the straps (see circle above).

Using two hands, slide one of the reservoirs towards you holding the handle in one hand.IMPORTANT: This may be heavy (less than 10kg) so take care when removing.

After emptying the reservoirs, replace by standing them on the reservoir holder. Ensure the handles are at the front for ease of emptying and the warning stickers are facing towards the door .

9. 10.

Repeat step 8 to remove the second reservoir.

11. NOTE: To clean the funnel �lter caps, open the door and push the caps upwards from the inside of the bin.

COMBO IS A TRADEMARK OF GLASDON GROUP AND ITS SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES.

Replacement components are available direct from GLASDON.

GLASDON cannot be held responsible for claims arising from incorrect installation, unauthorised modifications or misuse of the product.

Issue 1 July 2013 C000/0449© Copyright July 2013

Glasdon U.K. Ltd reserves the right to alter specifications without prior notice.Preston New RoadBLACKPOOLLancashire FY4 4ULTel: 01253 600410Fax: 01253 792558E-mail: [email protected]: www.glasdon.com

TM