Comandos MML Reunion Corto

Click here to load reader

download Comandos MML Reunion Corto

of 35

  • date post

    26-Dec-2015
  • Category

    Documents

  • view

    225
  • download

    7

Embed Size (px)

Transcript of Comandos MML Reunion Corto

NOKIA BSC COMMANDS

1. ZEEI ; - used to show the status of all sites in BSC2. ZEEI :BCF=(bcf no); - used to check status of particular BCF3. ZEOL:(BCF NO); - used to check alarm of particular Site.4. ZQSI ; - used to check status of X.25 link5. ZNEL; - to check status of all TCSM.

6. ZEFS:(bcf no):L/U; - used to lock/unlock BCF.7. ZEQS:BTS=(BTS no):L/U; - used to lock and unlock sector.8. ZERS:BTS=(BTS no):TRX=(TRx no):L/U; Used to lock/unlock individual TRx9. ZEFR:BCF NUM:OMU/SITE; OMU/SITE RESET10. ZAHO:ET,(ET.no) ; - To check alarm on ET. 30,3711. ZUSC:ET,E.no:BL/WO; - Used for making ET block and working. 12. ZDTF:TCSM,E.no ; - State checking of ET.13. ZEEL; -To see no. of calls continuing in a BSC

14. ZAHO; -To see all BSC related alarm37. ZAHP:::yyyy-mm-dd; -To know the alarm history of BSC21. ZIGO; - To know the MML application done with BSC since the last two remote session

15. ZEOL:(BCF no); -To see all alarm related to one BCF16. ZEOH:::BCF=BCF num; To see alarm history of a site17. ZEOL::NR=7706; -To see all sites having OMU blocked18. ZEOL::NR=7704; -To see all sites having PCM blocked19. ZEOL::NR=7705; -To see all sites having LAPD failure20. ZEOL::NR=7411; -To see all sites on battery21. ZQUS(Enter twice):BCF=(BCF no):TRE=1:2;7(Enter)1(Enter)200(Enter) - To know the receiving power of a PDH link :ODU:22. ZEEL:BCF(Enter)Select Option; -To know the blocked BCF/BTS/TRx category ZEEL:BL-USR:BCF= ;

25. ZYMO:ET,E.no ; - to check slips on ET23. ZYEF:ET,(ET no); - Checking loop in ET24. ZEOH:yy-mm-dd:hh-mm-ss:bcf=(bcf no); - Alarm related to particular date and time26. ZZZZ; - to terminate a remote session 27. ZDSB:::PCM=(ET no); - To find BCF no from a ET no/ Shows D channel details 28. ZDTI:::PCM=(ET num); -To find D channel details29. ZEOH::NR=7767; -To see the alarm num history in BSC for the last 00.00.00 hours 30. ZEOL::NR=7767; -To find out the sectors down in one BSC

31. ZQSC(ENTER) QSC:0(ENTER) QSC:0,UNL;(ENTER) Command to change physical address ZQSC(ENTER) QSC:1(ENTER) QSC:1,UNL;(ENTER)

32. ZQLG(ENTER) QLG:0(ENTER) QLG:0;X2(ENTER) QLG:0:X25:UNL;(ENTER) Command to change linkage ZQLG(ENTER) QLG:1(ENTER) QLG:1;X2(ENTER) QLG:1:X25:UNL;(ENTER)

Comment- If the X.25 link of BSC is locked from remote end the this command is used to unlock the X.25 link from local BSC end. Then both the command (28,29) should be executed

33. ZDSB:::PCM=(ET NO); To know wheather a ET is in use or not in use34. ZWUP:ET NUM; - To know a ET type(TCSM/Abis) 35. ZQNI; -To know the numerical ID of a BSC 36. ZQRI:OMU; -To know the local IP allotted to BSC38. ZERO:BCF=(BCF NUM); -To know the TSC value for each trx39. ZQWL:BCF=76; TO know the Q1 address of FIU s present in a site40. ZEFO:BCF ID:IOP; To know the alarm configuration in a bts site41. ZEFX:BCF NUM:INBR=alarm number:POL=OPEN/CLOSE; To change polarity of an external alarm42. ZEFE: -External Alarm text modification command43. ZDTC: D-channel name: BL/ WO; To change the state of D-channel 44. ZERC: Trx creation45. ZERD: Trx Deletion (trx should be locked before deletion)

46. ZDSE: Lap-D creation

///////////////////////////////////////////////////////////////////////////////////////////////////

1 open0 close

ZEFX:361:INBR=15:POL=CLOSED,ROU=ACT,:SEV=AL2,TID=15,:; (bcf) posicion Polaridad

NORMAMENTE CERRADANUM AL

///////////////////////////////////////////////////////////////////////////////////////////////////////////////

Nokia Command List

NOKIA COMMANDS:

Hot Keys:

Ctrl + B repeats last and previous commands on the MML

Ctrl + Y interrupts current command being typed or run

Alarm monitoring:

ZAHO; displays current active alarms in actual MSC and BSC only

ZEOL:#; displays active alarms on BCF (BCF = Site Manager or CF)

ZEEI:BCF=#; displays the operational state of the site

ZEOH:date,time:BCF=#; displays alarm history for site for the date and time listed

ZAHO:ET,#; displays current alarms for that ET (PCM)

ZAHP:ET,#; displays alarm history for that ET

ZEEL:BL; displays locked Sites, Sectors and TRXs on BSC

/////////////Zefo:#BCF:IOP; Muestra alarmas configuradas////////

Investigating Clear Codes:

ZTUT:CLR; displays current clear codes on the MSC

ZTUL:CLR; displays latest history of clear codes

Canceling Bogus alarms on a Site: (Perform both commands)

ZEOR:#:alarm #; cancels alarm on site

ZEFR:#:OMU; resets the OMU (Operations and Maintenance Unit)

Canceling Bogus alarms on a BSC:

ZACC:####; cancels the alarm using the consecutive # in which it came in

ZACA:####; cancels the alarm using the alarm identifier #

Locking and unlocking a Site:

ZEFS:bcf #:L; locks entire Site without Forced Handover

ZEFS:bcf #:U; unlocks entire Site

Locking and unlocking Sectors:

ZEQS:BTS=#:L; locks entire sector down without Forced Handover

ZEQS:BTS=#:L:FHO,#; shuts down entire sector with Forced Handover

ZEQS:BTS=#:U; unlocks entire sector

Locking and unlocking TRXs:

ZERS:BTS=#,TRX=#:L; locks TRX down without Forced Handover (bts es en zeei, ejemplo 1237 en bcf pero en zeeil es 1238)

ZERS:BTS=#,TRX=#:L:FHO,#; shuts down TRX with Forced Handover

ZERS: BTS=#,TRX=#:U; unlocks TRX

Resetting the Site or OMU:

ZEFR:#:SITE; restarts SITE (PARA RESETEAR SITIO EN GSM)

ZEFR:#:OMU; restarts OMU

Bouncing Lap Ds on a Site:

ZDTI:::PCM=#; displays Lap D channels for entire site

ZDTC:lap d #:BL; blocks desired Lap D channel

ZDTC:lap d #:WO; places Lap D channel in working state

Error Checking on an ET (PCM):

ZYMO:ET,#; checks error counter for specific ET

ZYEU:ET,#:SLIDL=5; resets error counter for specific ET

Querying the # of calls on a site:

ZERO:BTS=#; displays all calls on desired sector

ZERO:BTS=#,TRX=#; displays all calls on desired TRX only

Sparing or Rolling a BCSU:

ZUSI:BCSU; displays what BCSU the SP was previously on

ZFWO:BCSU=0&&8; displays what BCSU the BL condition is on

ZUSC:BCSU,#:SP; spares the BCSU with the BL condition on it

Y for Yes executes the command

Statusing Timeslots:

ZEEL::BCF=#; Status the timeslots on a BCF

Status ET alarms on a BSC

ZAHP:ET,:::; Show all ET's that are in alarm

Taking an ET out of Seperated State

ZUSC:ET,#:SE; Will place the ET in a Separated - No Hardware state

(SE-NH)

Status session for User ID and commands:

ZIGO: Displays commands run for BSC on specific date and time.

Reloading software on a site:

ZEWV:BCF #:BU; Reloads the software on a BCF

Checking OMC alarms:

Open a terminal and telnet to the IP

Log in

Run the following command: df k

Taking an ET out of BL state:

ZUSC:ET,#:

WORKING

BLOCKED

TEST

SEPERATED

SEPERATED-NO HARDWARE

Go back up the tree to get it back into Working

Rolling the BCCH on a Sector:

ZDTI:::PCM=#; Find out what TSL the radio is on that you want the BCCH on

ZDTC:lapd:BL; Block the TSL on the radio that the BCCH is going to

ZDTC:lapd:AL; Allow activation of the TSL that the BCCH is going to

ZDTC:lapd:WO; Brings TSL to a working state that the BCCH is going to

ZDTI:::PCM=#; Find out what TSL the radio that HAD the BCCH is on

ZDTC:lapd:AD; Deny Activation of the TSL that HAD the BCCH on it

ZDTC:lapd:BL; Block the TSL that the BCCH was on

ZDTC:lapd:WO; Brings the TSL to a working state

Clearing Circuit Releasing Failed in CAS alarms:

The alarm that you are talking about happens on MF circuits and is caused by the LEC not releasing or acknowledging us quick enough. Do to the latency, the Nokia locks out the trunk in question. When you see this alarm you should assume that it is 911 related and the issue needs to be corrected ASAP. The alarm field will be shown below.

SLMSC001 CASU-1 SWITCH 2005-11-27 00:07:37.44

*** ALARM CASU-1 1E001-00 SI9_SO

(9952) 2153 CIRCUIT RELEASING FAILED IN CAS

1081d 13d 29 0823 01 FF 01 02 01 01 10 00 00 00

If you look above I have highlighted in red the circuit that needs to be reset (1081-13). If you take the circuit to a NU state for about 30 seconds and then back to WO it should clear.

ZCEC:CRCT=1081-1:BA;

ZCEC:CRCT=1081-1:NU;

ZCEC:CRCT=1081-1:BA;

ZCEC:CRCT=1081-1:WO;

Also, you should get a Low Traffic Capacity alarm with supplementary information. I have the alarm listed below and the supplementary info is in red (02 0386). If you convert 386 from HEX to Decimal it comes out to 902. At that time you can do the command ZRCI:SEA=3:CGR=902:PRINT=5:; and look at the circuit group.