Cisco CH4
Transcript of Cisco CH4
-
7/28/2019 Cisco CH4
1/6
CCNA3 Chapter 4 Practice Test Answers
What is the default Catalyst switch configuration?
VTP version 1, Mode server, Domain name cisco1, revision number1.
VTP version 1, Mode server, no Domain name, revision
number 0.
VTP version 2, Mode server, no Domain name, revision number 0.
VTP version 1, Mode client, Domain name cisco1, revision number
0.
Which switches can only use VTP version 1, and not version 2?
Catalyst 2960 switches All Catalyst switches
Older Cisco switches
Non-Cisco switches
If you have a domain of switches that are all capable of using version 2, and youwant them to use version 2, which switches must you configure for version 2?
All switches
All server switches
Any server switch
Any switch
You have a group of switches that have never been configured for VTP, and youwant them to act as a VTP domain. What is the best way of ensuring that they allhave the same domain name?
Configure the name on one switch that is in server mode and
allow the name to propagate to the other switches.
Configure the name on one switch, copy the name, and paste it to
the other switches.
Configure the name on one switch, copy the configuration to aTFTP server, and download it to the other switches.
It does not matter whether they have the same domain name or not
as long as they are using the same version and the same password.
-
7/28/2019 Cisco CH4
2/6
Why should you configure a domain name on a server switch before creating theVLANs that you want to share with the domain?
VLANs cannot be created on a switch until the domain name is
configured.
Existing VLANs (except the default VLAN) are deleted whenyou configure a domain name.
VLANs created before the domain name is configured will be local
to the switch.
You need to create VLANs in VTP configuration mode.
Which is true about the switches in the diagram?
S1 must be in the same VTP domain as S4
S8 must be in the same VTP domain as S9
S2 cannot be in the same VTP domain as S6
S4 cannot be in the same VTP domain as S7
All the switches have the same VTP domain name. S1 has been configured as aserver. Which is true?
All the other switches in the domain must be configured as either
client or transparent. S4 should not be transparent as this will cut S5 and S6 off from the
rest of the domain.
S4, S5 and S6 can form their own domain as well as belonging to
the same domain as S1.
S5 may be a server switch in the same domain as S1.
Which is true of VTP?
It operates at OSI layer 1
It operates only on Cisco switches
A VTP domain can extend beyond a layer 3 switch
VTP is enabled by default on Catalyst switches
Which of these is not the name of a VTP advertisement?
Summary advertisement
Request advertisement
-
7/28/2019 Cisco CH4
3/6
-
7/28/2019 Cisco CH4
4/6
-
7/28/2019 Cisco CH4
5/6
The switches have ports assigned to the VLANs shown. What is the best way ofrestricting VLAN 4 broadcast transmissions in order to cut down unnecessarytraffic?
Enable VTP pruning on the switches.
Add a router between S1 and S4.
Have two separate VTP domains, one for S1, S2 and S3 and the
other for S4, S5 and S6.
Make S1 into a transparent mode switch.
What triggers a VTP server switch to send a summary advertisement? Chooseall that apply.
A 5 minute timer expires.
A new VLAN has just been configured on the switch.
An existing VLAN has just had its name changed.
A Switchport had just been moved from one VLAN to another.
The switches are not exchanging VLAN information correctly. What is the likely
problem?
One of the switches is in the wrong mode.
One of the switches does not have switchports in VLANs 2 or 3.
The switches do not all have the same config revision number.
The switches are not all in the same VTP domain
-
7/28/2019 Cisco CH4
6/6