CineVision Game Assembly DOC-103500

CineVision Game Assembly

CineVision Game Assembly DOC-103500

Assemblies: 103126, 105502, 104217


Technical Publications – Las Vegas, Nevada DOC-103500

Publication Date: February 25, 2011 VERSION .01


Copyright

Copyright 2005 Bally Gaming, Inc. Rights Reserved.The following are trademarks of Bally Gaming, Inc.:

CineVision

All other product names and trademarks are the intellectual property of their respective owners. Thisdocumentation contains confidential and proprietary information of Bally Gaming, Inc. No portion ofthis document may be reproduced or transmitted in any form or by any means, electronic or mechanical,for any purpose, without the express written permission of Bally Gaming, Inc.

The specifications and information contained in this documentation are subject to change without notice.All statements, information, illustrations, specifications and recommendations in this documentation arebelieved to be accurate but are provided without warranty of any kind, expressed or implied.

In Las Vegas In the US and Canada Outside the US

PH: 896-7772FAX: +1-702-896-7710

PH: 1-877-GO BALLY(877-462-2559)

PH: 1-702-896-7772




Page iii of 34

Visit our website at http://www.ballygaming.com




Page iv of 34

Contents

Introduction....................................................................................................................6About this Guide .....................................................................................................................6Parts and Assemblies .............................................................................................................6Recommended Tools & Supplies............................................................................................6

Cabinet Parts Kit............................................................................................................8Parts and Assemblies .............................................................................................................8Speakers .............................................................................................................................. 10Cable Interconnect Brackets .................................................................................................11Door Switches ......................................................................................................................12Base Shelf ............................................................................................................................13Main Cabinet Door Lock .......................................................................................................13Catch Bottle and Tubing .......................................................................................................14Footrest ................................................................................................................................ 14Processor/Power Supply Assembly ......................................................................................154-Meter PCB.........................................................................................................................20Audio Board Tray & Chassis .................................................................................................20Deck Bulkhead .....................................................................................................................2126" LCD Touch Screen .........................................................................................................23Gas Struts............................................................................................................................. 25

Cabinet Base Assembly ..............................................................................................26Parts and Assemblies ...........................................................................................................26Lower Door ...........................................................................................................................26Lock and Cam ......................................................................................................................27Front Base Panel ..................................................................................................................28

Top Box Assembly ......................................................................................................28Top Box Cabinet ...................................................................................................................30

Door Switch ........................................................................................................................................31Top Box Door .......................................................................................................................32

Lock and Cam.....................................................................................................................................33




Page v of 34




of 34

Introduction

About this Guide

The purpose of this document is to assist Bally Gaming assembly technicians with a CineVision cabinetassembly. This document is divided into three sections as follows.

Table 1: Installation

Section Description

One Main Cabinet Assembly

Two Cabinet Base Assembly

Three Top Box Cabinet Assembly and Installation

Parts and Assemblies

Portions of the CineVision cabinet are preassembled and installed prior to reaching Bally’s assembly line.Remaining portions of the assembly require the contents of 103126 (Cabinet Parts Kit), 105502 (CabinetBase Assembly), and 104217 (Top Box Parts Kit). The contents of each kit are listed at the beginning ofsections one, two, and three as described in Table 1. See Table 2 for the hardware needed to install thecontents of each parts kit:Table 2: Required Hardware

Part Number Description Quantity

18454 Shoulder Washer 3

NLS-LSPP-M0470-1205 Screw 6

NLS-LSPP-M0350-1206 Screw 4

NLS-M0350-1206 Nut 8

NLS-M0470-1117 Nut 40

Recommended Tools & Supplies

Be sure to have the following tools and supplies available throughout the assembly:




of 34

Phillips Screwdriver 11/32", 3/8", 5/16" nut drivers

Side Cutters Cable Ties (p/n E-00647-0005)




of 34

Cabinet Parts Kit

For this portion of the assembly, you will install the following components (numbered accordingly in

1. 4" Speakers2. 6" Speaker3. Cable Interconnect Brackets4. Main Cabinet Lock & Cam5. Door Switches

6. Base Shelf7. Catch Bottle and Tubing8. Footrest9. MPU/Pwr Supply Assembly10. 4-Meter PCB Assembly

11. Audio Tray & Chassis12. Deck Bulkhead13. 26" LCD Touch Screen14. Gas Struts


Verify you have the parts and assemblies included in the Cabinet Parts Kit (103126) as listed in Table 3:

Table 3: 103126 Contents

Reference Part Number Description Quantity

Figure 1 104212 20W, 4" Speaker 2

Figure 3 103250 Speaker Grill 1

Figure 3 100673-00001 50W, 6" Speaker 1

Figure 4 101609 Cable Interconnect Bracket (Right) 1

Figure 4 101892 Cable Interconnect Bracket (Left) 1

Figure 8 M-002810170 Lock w/o Cam 1

Figure 8 SDG-20228 1-⅛" x ¾" Cam 1

Figure 6 E-00108-0384 Door Switch 3

Figure 7 104805 Base Shelf 1

Figure 9 104798 Catch Bottle 2

Figure 10 104799 6" Water Diversion Tubing 2

Not Shown 104808 2" Self-Adhesive Hook and Loop Tape 2

Figure 11 103419 Footrest 1




of 34

Figure 13 103470 Processor/Power Supply Assembly 1

Figure 16 103094 5v/12v Power Supply 1

Figure 16 103107 24v Power Supply 1

Figure 18 44603 MPU Assembly 1

Figure 19 SDG-26460-4 4-Meter PCB 1

Figure 21 SDG-41060 Audio Board Tray 1

Figure 22 SDG-41061 Audio Board Chassis 1

Figure 24 103672 Deck Bulkhead 1

Figure 28 103694 26" LCD Touch Screen 1

Figure 29 103630 Side Grill 2

Figure 30 103575 Side Grill Backing 2

105054 Gas Strut w/o Latch 2

103681 Lower Strut Mount 2

Upper Strut Mount ?????? 2




of 34

Speakers

STEP 1: Use four nuts (NLS-M0470-1117) to install both 4" Speakers (104212) on top of theupper portion of the cabinet.

a. Be sure the terminals on each speaker point to the center of the cabinet as shownin Figure 2.

STEP 2: St the Speaker Grill (103205) onto the four studs surrounding the speaker opening onthe inside of the cabinet.

STEP 3: Place the 6" Speaker (100673-00001) onto the grill (see Figure 1).

STEP 4: Secure the speaker and grill to the cabinet using four nuts (NLS-M0470-1117).




of 34

Figure 1: Speaker Installation

Figure 2: 4" Speaker Orientation

Figure 3: 6'' Speaker Assembly

Cable Interconnect Brackets

STEP 1: Use two nuts (NLS-M0470-1117) to mount the left Cable Interconnect Bracket (101892)in the designated opening in the upper portion of the cabinet (next to the left speaker).

STEP 2: Use two nuts (NLS-M0470-1117) to mount the right Cable Interconnect Bracket(101609) in the designated opening in the upper portion of the cabinet (next to the rightspeaker).




of 34

Figure 4: Cable Interconnect Brackets

Door Switches

STEP 1: Locate each of the three doorswitch brackets numbered inFigure 6.

STEP 2: Insert a Door Switch (E-00108-0384) into each of the brackets.

Figure 5: Door Switch BracketsFigure 6: Door Switch




of 34

Base Shelf

STEP 1: Set the Shelf Base (104805) insidethe base of the cabinet

a. Be sure to set the shelf asfar back into the cabinetas possible.

STEP 2: Tighten the thumb-bolts tosecure the shelf to the base of thecabinet.

Figure 7: Installed Base Shelf

Main Cabinet Door Lock

STEP 1: If necessary, disassemble the Lock (M-00281-0170), and set hardware aside.

STEP 2: Press the lock into the designated holeunderneath the armrest on the maincabinet door.

STEP 3: Place the Cam (SDG-20228) onto thelock from the backside of the panel.

STEP 4: Tighten the cam in place using thehardware removed in Step 1 (seeFigure 8).

Figure 8: Lock Hardware

Base Shelf




of 34

Catch Bottle and Tubing

STEP 1: If necessary, cut the Hook and Loop Tape (104808) to create two 2" pieces.

STEP 2: Use one 2" piece to mount a Catch Bottle (104798) in the back of the cabinet base, on theright and left

STEP 3: If necessary, cut the Water Diversion Tubing (104799) to create two 6" pieces.

STEP 4: Place one end of each 6" tube onto the stand-off located directly above each catch bottle(magnified in Figure 10).

Figure 9: Catch Bottle InstallationFigure 10: Catch Bottle and Tubing

Footrest

STEP 1: Secure the Footrest (103419) to thecabinet using three ??? (?????) asshown in Figure 11.

Figure 11: Footrest Figure 12: Footrest Installation




of 34

Processor/Power Supply Assembly

STEP 1: Use four nuts (NLS-M0470-1117) tomount the processor/power supply(103470) onto four studs (numberedin Figure 14) in the lower portion ofthe cabinet.

a. Be sure the backplane restssecurely on the bottom ofthe cabinet as in Figure 15.

Figure 13: MPU/Power Supply (103470)Figure 14: 103470 Mount Location

Figure 15: Mounted MPU/Power Supply

Backplane




of 34




of 34

STEP 2: Slide the 5v/12v Power Supply (103094) onto the left side of the MPU/power supplyassembly.

STEP 3: Slide the 24v Power Supply (103107) onto the right side of MPU/power supply assembly.

STEP 4: Tighten the thumb-bolts on each power supply to secure in place.

Figure 16: Power Supplies

STEP 5: Slide the MPU (44603) into the MPU/power supply assembly below the power supplies.

Figure 17: Complete MPU/Power Supply Assembly

5v/12v Power Supply 24v Power Supply

MPUMPU Cables




of 34

STEP 6: Notice the MPU cables attached to the left side of the housing Figure 17.

STEP 7: Refer to the following chart andFigure 18 and connect theMPU cables accordingly:

Ref (Figure 18) Cable

1 Touch Screen (E-00664-0710)

2 VGA (E-00664-0708)

3 MPU Power (E-126-184)

4 Audio (Line Out)

Figure 18: MPU Cable Connections

STEP 8: Route the XX portion of the Main Cabinet Harness (104225) along the back, right cornerof the cabinet.

STEP 9: Route the XX portion of the main cabinet harness along the back, left corner of thecabinet.

1

4

3

2

1

2

3

4




of 34

S




of 34

4-Meter PCB

STEP 1: Use four screws (LSPP-M0350-1206) to mount the 4-Meter PCB (SDG-26460-4) to the

Figure 19: SDG-26460-4

Figure 20: SDG-26460-4 Mount Location

Audio Board Tray & Chassis

STEP 1: Use four nuts (NLS-M0470-1117) to secure the Audio Chassis (SDG-41061) to the leftside of the cabinet as shown in Figure 22.

Touch Screen Area




of 34

Figure 21: Audio Board Tray and Chassis Figure 22: Chassis Mount Location

STEP 2: Slide the Audio Board Tray(SDG-41060) into the chassis.

STEP 3: Tighten the thumb-bolt tosecure the tray in place.

Figure 23: Audio Board Tray and Chassis

Deck Bulkhead

STEP 1: Mount the Deck Bulkhead (103672) on the two studs to the right of the 4-meter PCB,below the touch screen area.




of 34

Figure 24: Deck Bulkhead (103672)

STEP 2: Secure the bulkhead to the cabinet with two nuts (NLS-M0470-1117).

Figure 25: Bulkhead Mount Location Figure 26: Mounted Deck Bulkhead

STEP 3: Locate the Cabinet Harness (104225) connected to the MPU/power supply assembly.

STEP 4: Insert the following connectors into deck bulkhead precisely as listed in the followingchart:

Connector Description Position (see Figure 27)

10-pin Deck Button-Switches Top (1)

9-pin Door Cable Interface Middle opening (2)

12-pin Deck Button-LEDs Bottom opening (3)

Figure 27: Deck Bulkhead Connectors

Touch Screen Area




of 34

26" LCD Touch Screen

STEP 1: Set the LCD Touch Screen(103694) onto the two studslocated on the right and left sideof the touch screen area (circled inFigure 28).

STEP 2: Tighten a nut (NLS-M0470-1117)onto each stud (4 total) to securethe touch screen in place.

STEP 3: Insert and tighten a screw (NLS-LSPP-M0470-1205) in theremaining holes (6 total) on eachside (numbered in Figure 28).

Figure 28: Mounting the Touch Screen




of 34

STEP 4: Slide a Side Grill (103630) onto each of the two Side Grill Backings (103575).

Figure 29: Side Grill Assembly

STEP 5: Locate the monitor rail posts each corner of the touch screen (see Figure 28 and Figure30).

STEP 6: Place an assembled side grill on each of the bottom rail posts.

IMPORTANTNotice the rubber strip along the inside edge of each grill. Be sure to position the grillwith the rubber edge against the touch screen.

STEP 7: Press the top portion of each grill against the monitor until it locks onto the top rail post.




of 34

Figure 30: Installing the Side Grills

Gas Struts




of 34

Cabinet Base Assembly

For this portion of the assembly, you will install the following components to assemble the cabinet base.

1. Lower Door 2. Lock and Cam 3. Front Base Panel


Verify you have the parts and assemblies included in the Cabinet Base Assembly (p/n 105502) as listed inTable 4.

Table 4: 105502 Contents


Figure 31 103982 Lower Door 1

Figure 33 M-002810170 1.125L Lock w/o Cam 1

Figure 33 SDG-20228 1-⅛" x ¾" Cam 1

Figure 32 103462 Front Base Panel 1

Lower Door

STEP 1: Use three nuts (NLS-M0470-1117) to mount the Lower Door (103982) onto the cabinetas in Figure 31.




of 34

Figure 31: Lower Cabinet Door

Lock and Cam

STEP 1: If necessary, disassemble the Lock (M-00281-0170), and set hardware aside.

STEP 2: Press the lock into the designated hole in the Front Base Panel (103462) as in Figure 32.

STEP 3: Place the Cam (SDG-20228) onto the lock from the backside of the panel.

STEP 4: Tighten the cam in place using the hardware removed in Step 1.

a. Be sure to replace the hardware in the exact order demonstrated in Figure 33.




of 34

Figure 32: Front Base Panel


Front Base Panel

STEP 1: Slide the bottom edge of the panel into thecabinet.

STEP 2: Lift the top portion of the panel to close.

STEP 3: Turn the key to lock the panel in place.

STEP 4: Leave the key in the lock.

Figure 34: Front Base Panel

Top Box Assembly

This portion of the assembly involves the assembly and installation of the top box, which includes thefollowing:




of 34

1. Top Box Cabinet 2. Top Box Door


103686 Arch Top Enclosure (Top Box Cabinet) 1

SDG-30294 24V, Dual Fluorescent Lamp Assembly 1

103706 Top Box Door 1

104743 Candle Mount 1

105583 Candle Mount Gasket 1

103708 Lower Glass Clamp 1

103709 Upper Glass Clamp 1

M-00281-0167 Lock w/o Cam 1

104888 1" Cam Hook 1

E-00108-0385 Door Switch 1

CBL-31047-0001 25" Top Box Tower Light Cable 1

CBL-31048-0001 25" Top Box DC Fluorescent Cable 1




of 34

Top Box Cabinet

STEP 1: Lay the Top Box Cabinet (103686) on a flat surface with the front side facing up.

STEP 2: Use two nuts (NLS-M0470-1117) to mount the 24V, Dual Fluorescent LampAssembly (SDG-30294) inside the top box.

Figure 35: Mounted Lamp Assembly

Lamp Assembly




of 34

Door SwitchSTEP 1: Locate the door switch bracket on the right side of the top box cabinet.

STEP 2: Insert the provided Door Switch (E-00108-0385) into the bracket.

Figure 36: Top Box Door Switch




of 34

Top Box Door

STEP 1: Notice the logo plate on the front of the Top Box Door (103706).

STEP 2: Lay the top box door on a flat surface with the front side facing down.

STEP 3: Carefully set the Top Box Glass (G-R0860) inside the doorframe.

STEP 4: With the gasket side firmly against the glass, set the Lower Glass Clamp (103708) onto thethree studs inside the doorframe.

STEP 5: Use three nuts (NLS-M0470-1117) to secure the glass in place.

Figure 37: Top Box Door Assembly

STEP 6: If necessary, cut two 2" self-adhesive gasket strips (R-00553-0011).

STEP 7: Peel and stick one gasket strip on the backside of each Upper Glass Clamp (103709).

STEP 8: With the gasket side firmly against the upper edge of the glass, secure each glass clamp tothe doorframe with one (NLS-M0470-1117).

Picture goes here




of 34

Lock and CamSTEP 1: If necessary, disassemble the top box Lock (M-00281-0167).


STEP 2: Insert the lock into the designated hole on the top of the top box cabinet.

STEP 3: From the inside of the cabinet, place the Cam (104888) onto the lock.

STEP 4: Secure the cam in place using the hardware removed in Step 1.

a. Be sure to install the hardware in the exact order illustrated in Figure 38.




of 34

Figure 39: Installing the Lock and Cam

CineVision Game Assembly DOC-103500

Documents

Transcript of CineVision Game Assembly DOC-103500