8/10/2019 ChemEngineering - Flash Evaporation

1/3

12/25/2014 ChemEngineering - Flash evaporation

https://chemengineering.wikispaces.com/Flash+evaporation 1/3

Flash evaporation (/Flash+evaporation) 0 (/page/messages/Flash+evaporation)

26 (/page/history/Flash+evaporation) (/page/menu/Flash+evaporation)

A

typical

flash

drum

Flash evaporation is the partial or total vaporization that occurs when a saturated liquid

stream undergoes a reduction in pressure by passing through a throttling valve or other

throttling device. This process is one of the simplest unit operations. If the throttling valve

or device is located at the entry into a pressure vessel so that the flash evaporation occurs

within the vessel, then the vessel is often referred to as a flash drum.

If the saturated liquid is a single-component liquid (for example, liquid propane or liquid ammonia),

a part of the liquid immediately "flashes" into vapor (i.e., evaporates). Both the vapor and the

residual liquid are cooled to the saturation temperature of the liquid at the reduced pressure. This is

often referred to as "auto-refrigeration" and is the basis of most conventional vapor-compression

refrigeration systems.

If the saturated liquid is a multi-component liquid (for example, a mixture of propane, isobutane and

normal butane), a part of the liquid will also immediately flash into a vapor and the flashed vapor

will be richer in the more volatile components than is the remaining liquid.

Flash evaporation of a single-component liquid

The flash evaporation of a single-component liquid is an isenthalpic (i.e., constant enthalpy)

process and is often referred to as an adiabatic flash, a flash distillation or a throttling expansion.The following equation, derived from a simple heat balance around the throttling valve or device, is

used to predict how much of a single-component liquid is vaporized when it "flashes":

X = 100 ( HuL Hd

L ) ( HdV Hd

L )

where:

X = weight percent vaporized

HuL = upstream liquid enthalpy at upstream temperature and pressure, J/kg

HdV= flashed vapor enthalpy at downstream pressure and corresponding saturation

temperature, J/kg

HdL = residual liquid enthalpy at downstream pressure and corresponding saturation

temperature, J/kg

If the enthalpy data required for the above equation is unavailable, then the following equation may

be used.

X = 100 cp (Tu Td) Hv

where:

X = weight percent vaporizedcp = liquid specific heat at upstream temperature and pressure, J/(kg C)

Tu= upstream liquid temperature, C

Td= liquid saturation temperature corresponding to the downstream pressure, C

You are not a member of this wiki. Join now

(https://chemengineering.wikispaces.com/space/join) Dismiss

https://chemengineering.wikispaces.com/vapor-compression+refrigerationhttps://chemengineering.wikispaces.com/vapor-compression+refrigerationhttps://chemengineering.wikispaces.com/vapor-compression+refrigerationhttps://chemengineering.wikispaces.com/vapor-compression+refrigerationhttps://chemengineering.wikispaces.com/vapor-compression+refrigerationhttps://chemengineering.wikispaces.com/vapor-compression+refrigerationhttps://chemengineering.wikispaces.com/pressurehttps://chemengineering.wikispaces.com/page/history/Flash+evaporationhttps://chemengineering.wikispaces.com/page/history/Flash+evaporationhttps://chemengineering.wikispaces.com/page/messages/Flash+evaporationhttps://chemengineering.wikispaces.com/Flash+evaporationhttps://chemengineering.wikispaces.com/space/joinhttps://chemengineering.wikispaces.com/vapor-compression+refrigerationhttps://chemengineering.wikispaces.com/space/joinhttps://chemengineering.wikispaces.com/Flash+evaporationhttps://chemengineering.wikispaces.com/page/menu/Flash+evaporationhttps://chemengineering.wikispaces.com/page/history/Flash+evaporationhttps://chemengineering.wikispaces.com/page/messages/Flash+evaporationhttps://chemengineering.wikispaces.com/pressure

8/10/2019 ChemEngineering - Flash Evaporation

2/3

12/25/2014 ChemEngineering - Flash evaporation

https://chemengineering.wikispaces.com/Flash+evaporation 2/3

Equilibrium

flash of a

multi-

component

feed

Hv= liquid heat of vaporization at downstream pressure and corresponding saturation

temperature, J/kg

( Note: The words "upstream" and "downstream" refer to before and after the liquid passes through

the throttling valve or device.)

This type of flash evaporation is used in the desalination of brackish water or ocean water by Multi-

Stage Flash Distillation. The water is heated and then routed into a reduced-pressure flashevaporation "stage" where some of the water flashes into steam. This steam is subsequently

condensed into salt-free water. The residual salty liquid from that first stage is introduced into a

second flash evaporation stage at a pressure lower than the first stage pressure. More water is

flashed into steam which is also subsequently condensed into more salt-free water. This sequential

use of multiple flash evaporation stages is continued until the design objectives of the system are

met. A large part of the world's installed desalination capacity uses multi-stage flash distillation.

Typically such plants have 24 or more sequential stages of flash evaporation.

Equilibrium flash of a multi-component liquid

The equilibrium flash of a multi-component liquid is also an isenthalpic process and

may be visualized as a simple distillation process using a single equilibrium stage. It is

very different and more complex than the flash evaporation of single-component liquid.

For a multi-component liquid, calculating the amounts of flashed vapor and residual

liquid in equilibrium with each other at a given temperature and pressure requires a trial-

and-error iterative solution. Such a calculation is commonly referred to as an

equilibrium flash calculation. It involves solving the following Rachford-Rice equation:

where:

zi = mole fraction of component i in the feed liquid

= mole fraction of feed that is vaporized = V/F

Ki = vapor-liquid equilibrium constant = yi/xi

yi = mole fraction of component i in the flashed vapor

xi = mole fraction of component i in the residual liquid

Newton's method (also known as the Newton-Raphson method) is an efficient iterative algorithm forsolving the Rachford-Rice equation. Alternatively, the bisection method or the Brent method may

be used. Once the equation has been solved for , the compositionsxi and yi can be immediately

calculated as:

The equilibrium flash of multi-component liquids is very widely utilized in petroleum refineries,

petrochemical and chemical plants and natural gas processing plants.xx

Image credits

Both images in this article were created by Milton Beychok and are released into the Public

Domain.

[1] [2] [3] [4]

( 1 ) 1 + ( 1 ) = 0

= 1

K

K

= 1 + ( 1 )

K

=

K

https://chemengineering.wikispaces.com/Petroleum+refining+processes

8/10/2019 ChemEngineering - Flash Evaporation

3/3

12/25/2014 ChemEngineering - Flash evaporation

https://chemengineering.wikispaces.com/Flash+evaporation 3/3

Help About Blog Pricing Privacy Terms Support Upgrade

Contributions to https://chemengineering.wikispaces.com/ are licensed under a Creative Commons

Attribution No-Derivative-Works Non-Commercial 3.0 License.

Portions not contributed by visitors are Copyright 2014 Tangient LLC

References

1. ^ Editors:Don W. Green and Robert H. Perry(2007), Perry's Chemical Engineers' Handbook,

8th Edition, McGraw-Hill Professional, ISBN 0-07-142294-3

2. ^Harry Kooijman and Ross Taylor (2000), The ChemSep Book, 2nd Edition, ISBN 3-8311-

1068-9. Available online at The ChemSep Book (See pdf page 186 of 194 pdf pages)

3. ^Module Elementary Vapor-Liquid Equilibrium (From the website of the Pennsylv aniaState University)

4. ^Flash Calculations using the Soave-Redlich-Kwong equation of state (Click on the small

image to view it legibly at full-size)

https://www.wikispaces.com/termshttps://www.wikispaces.com/site/help?url=https%3A%2F%2Fchemengineering.wikispaces.com%2FFlash%2Bevaporationhttp://www.chemsep.com/downloads/docs/book2.pdfhttps://www.e-education.psu.edu/png520/m13_p2.htmlhttp://www.creativecommons.org/licenses/by-nc-nd/3.0https://help.wikispaces.com/https://www.wikispaces.com/abouthttp://blog.wikispaces.com/https://www.wikispaces.com/content/pricinghttp://www.creativecommons.org/licenses/by-nc-nd/3.0https://www.wikispaces.com/privacyhttp://www.mathworks.com/matlabcentral/fileexchange/loadFile.do?objectId=9341&objectType=filehttps://chemengineering.wikispaces.com/space/subscribe/upgrade