Chapter 3 Hydraulic CylindersChapter 3 Hydraulic Cylinders

Objectives: The purpose of this chapter is to describe:1. the types of cylinders, the different situations of application, the configurations of different cylinder components.2. the calculation of cylinders.3. the construction and seal of cylinders4. the basic design steps of cylinders. Upon completing this chapter, you should be able to: Distinguish the different types of cylinders, the different working conditions, the configurations of different cylinder components. Master the basic calculation of cylinders, especially the velocities and the output forces of cylinders. Understand the characteristics of two kinds of seal. Be familiar with the basic design steps of cylinders.

Chapter 3 Hydraulic CylindersChapter 3 Hydraulic Cylinders

/

piston cylinders

rams

reciprocating cylinders booster cylinders

Telescopic cylinders

rack and pinion cylinder

oscilating cylinders motors

Classification:

3.1 Types and Calculation of cylinders

3.1.1.1 Double-end rod cylinders A double-end rod cylinder has two piston rods in both ends.

(a) (b) Fig. 3.1 Double-end rod cylindersa. The cylinder body is stationary. b. The piston rod is stationary.

3.1.1 Piston type cylinders

A double-end rod cylinder has identical drive force and speed in both directions.

)(

422 dD

q

A

qv v

mppdDF ))((

4 2122

A single-end rod cylinder has only one rod. 3.1.1.2 Single-end rod cylinders

)(

4222dD

q

A

qv v

mpDpdDF ]

4)(

4[ 2

21

222

21

14

D

q

A

qv v

mpdDpDF

])(44

[ 222

12

1

Compare the equations above, we can draw a conclusion that v2>v1, F1>F2. The velocity ratio is )/(/ 222

12 dDDvv

The differential connection are usually used to increase the velocity of an end use device. The floating connection can make an end use device move freely.

uncertainv 404 F

234

d

qv v

mpdF

12

3 4

3.1 Types and Calculation of cylinders

3.1.2 Rams The bore of a ram need not accurately machining , so the initial cost is substantially low. However, a ram is controlled in single direction.

If double-acting is needed, a couple of rams should be used.

柱 塞p q

缸 筒

A

a（ ）

v

F

v

F

( b)

Apq

3.1 Types and Calculation of cylinders

3.1.3 Oscillating motors

Vane motors can be used to provide oscillatory motion of less than one complete rotation. Single vane motors can rotate less than 280 degrees and double vane motors can be limited to about 150 degrees.

D

d

1 2 3

4

4

3

2

41

1

3.1 Types and Calculation of cylinders

3.1.4 combination cylinders

Booster cylinders can convert the low input pressure into the high output pressure.

3.1.4.1 booster cylinders

12

12 p

A

Ap 02211 ApApFx

3.1 Types and Calculation of cylinders

3.1.4.2 Telescopic cylinders

A telescope cylinder consists of multilevel piston rods. The piston of previous level is the sleeve bore of rear level. The sequence of extension motion is: the first extension is stage 1, then stage 2, etc. The output force is decreassive and the velocity is increasive. on the contrary, the retraction sequence is reverse. The telescopic cylinder is used when a long stroke length and a short retracted length are required.

3.1.5 Rack and pinion cylinder

The rack and pinion cylinder incorporate a piston rod with a rack and a pinion. The rack and pinion drive is adaptable for rotational motions. It is usually used for angle displacement and graduators in automatic product line or combination machine, etc.

3.1 Types and Calculation of cylinders

Fig 3.9 Construction of double acting single-end rod cylinder l-cap 2-stirrup 3 、 5 、 9 、 11-seals 4-piston 6-barrel 7-rod end 8-bush 10-cover

3.2 Cylinder Construction

3.2.1 cylinder body component Chambers sealed by cylinder body component and piston component withstand oil pressure. Therefore, cylinder body component should be enough strength, high surface accuracy and reliable tightness.

3.1 Types and Calculation of cylinders

3.2.1.1 connection of cover and barrel

( a) ( b) ( c )

( d) ( e) ( f )

(1) The flange connection is simple, reliable and convenient to machine. However, the thickness of barrel end is required more to mount screw. (2) The whitney key type connection is convenient, reliable and compacted.

( a) ( b) ( c )

( d) ( e) ( f )

(3) The advantage of thread connection is little space, little weight and reliable. But the construction of barrel end is complicated. (4) The draw-bar type connection is simple, convenient. But volume and weight of cover is great. (5) The welding type connection is high strength and convenient to machine. But it is easy for the barrel to deform.

.2.1.2 basic requirement of barrel ,cover and guide sleeve

The surface roughness of the cylinder bore is from 0.1 to 0.4m The barrel is endured large force of oil pressure, therefore it should be enough strength and rigidity.

Covers are set up at both ends of barrel. It is also endured large force of oil pressure, therefore covers and its connection should be enough strength.

The guide sleeve guides and sustains the piston rod or ram. Therefore, the cover should be replacement after it is worn out.

The material selection of barrel, cover and oriented sleeve can refer hydraulic design handbook and specifications .

3.1 Types and Calculation of cylinders

3.2.2 Piston component 3.2.2.1 Connection forms of piston and rod

The threaded connection is simple and convenient to disassemble and assemble,

The semi-cyclic linkage has a advantage of high strength, it’s disadvantage is complicated and hard to disassemble and assemble.

3.1 Types and Calculation of cylinders

3.2.2.2 Piston component seal

1 Gap seal The gap seal depends on the slight clearance between two surfaces with relative motion to prevent leakage. It is simple in structure and has long life, but it does not ensure not to leak at all. In addition, it needs high machining accuracy. It is rational for the gap seal to be used in the case of rapid movement.

3 Seal by using seal packing ring

The seal by using seal packing ring has good tightness , does not need very high machining accuracy, but has not very long expected life, It is rational for the seal by using seal packing ring to be used in the case of slow motion.

3.1 Types and Calculation of cylinders

（ 1 ） O-ring

(2) V-ring

a) pressure ring b)V-ring c) supporting ring(3) Y-ring

( a) ( b)

3.2.3 Cushioning devices

Mounting cushion devices is usually needed when cylinder demand rapid movement and heavy load. The principle of cushion is increasing the back pressure of outlet port to reduce the cylinder velocity and protect the compact of piston and cover when piston or barrel is close to end of stroke.

u

d

u

( b)

u

( a)

c（ ）

u

( d)