CDT 30 MK III MOBILE DEHUMIDIFIER - Dantherm

01.2

0

dantherm.com

CDT 30 MK III

Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser• Adjustable handle• Plastic bumpers• Low weight• Stackable• Large wheels

Water container• Water container with handles• Automatic stop when water container is full or removed• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra

Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function

FunctionThe CDT 30 MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.

Applications• Damage service• Building drying• Water works• Dry storing

CDT 30 MK IIIMOBILE DEHUMIDIFIER

FEATURES

MOBILE DEHUMIDIFIERS CDT

Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter

DefrostingActive, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.

https://www.dantherm.com

01.2

0

dantherm.com

Specific energy consumption (SEC)• 0.53 kWh/l at 30°C & 80% RH• 0.85 kWh/l at 20°C & 60% RH

Accessories½” drain outletRemote hygrostatWall bracketRemote monitoring (IMCS)Condensate pump in a cassette(see separate data sheet)

Also available in this seriesCDT 30S MK IIICDT 40 MK IIICDT 40S MK IIICDT 60 MK IIICDT 90 MK III(see separate data sheets)

Model CDT 30 MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 15.1 l/dDehumidification – 30°C & 80% RH 31.9 l/dAir volume 250 m³/hPower supply 230 V/50 HzMax. ampere consumption 3.6 AMax. power consumption 0.8 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 56 dB(A)Water container capacity 7 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 31 kg

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS


Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.

AND WILL BE PROTECTED BY PATENTS

table LZT 142 0001, category

ohr

03-01-2012

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

65610.26g

SCALE: NOT TO SCALE

351 189

351189

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO

8Surface appearance according to reference BEND RADII:

ARE THE PROPERTY OF SAID COMPANY

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

REV.:

RE

V.:

CDT 30 MK II

CDT 30 MK II

PA

RT

NO

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

740

650

506

427




ohr

03-01-2012


65610.26g

SCALE: NOT TO SCALE

351 189

351189

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO




REV.:

RE

V.:

CDT 30 MK II

CDT 30 MK II

PA

RT

NO



740

650

506

427




ohr

03-01-2012


65610.26g

SCALE: NOT TO SCALE

351 189

351189

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO




REV.:

RE

V.:

CDT 30 MK II

CDT 30 MK II

PA

RT

NO



740

650

506

427

All dimensions are in mm.

736

650

426

0

5

10

15

20

25

30

35

40

0,00 0,20 0,40 0,60 0,80 1,00 1,20 1,40 1,60

°C

L/H

40% 60% 80%


01.2

0

dantherm.com

Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser• Adjustable handle• Plastic bumpers• Low weight• Stackable• Large wheels• On the back two Ø100 mm flex. air ducts may be connected

(max. length of 5 m) (accessory)• Built-in 1 kW heating element• Supplied with high pressure fan



FunctionThe CDT 30S MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.



CDT 30S MK IIIMOBILE DEHUMIDIFIER

FEATURES



CDT 30S MK III

01.2

0

dantherm.com

CDT 30 S MK II

CDT 30 S MK IISCALE: NOT TO SCALE

64278.09g

BEND RADII:

24-05-2012

ohr

351190

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

351 190

only entended as a guide.

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS



750

650

506

426

CDT 30 S MK II


64278.09g

BEND RADII:

24-05-2012

ohr

351190

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO


351 190


8






750

650

506

426

CDT 30 S MK II


64278.09g

BEND RADII:

24-05-2012

ohr

351190

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO


351 190


8






750

650

506

426

736

650


Accessories½” drain outletRemote hygrostatWall bracketRemote monitoring (IMCS)Condensate pump in a cassetteFlex. air ducts Ø100 mm(see separate data sheet)

Also available in this series:CDT 30 MK IIICDT 40 MK IIICDT 40S MK IIICDT 60 MK IIICDT 90 MK III(see separate data sheets)

Model CDT 30S MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 14.4 l/dDehumidification – 30°C & 80% RH 34.4 l/dAir volume 350 m³/h*Power supply 230 V/50 HzMax. ampere consumption 7.9 AMax. power consumption with heating element 1.8 kWMax. power consumption without heating element 0.8 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 56 dB(A)**Water container capacity 7 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 33 kg

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS



*Measured without air ducts mounted.**Measured with air ducts mounted.

0

5

10

15

20

25

30

35

40

0,00 0,20 0,40 0,60 0,80 1,00 1,20 1,40 1,60 1,80

°C

L/H

40% 60% 80%

01.2

0

dantherm.com

Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels

Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra





FEATURES



CDT 40 MK III


01.2

0

dantherm.com



Also available in this series:CDT 30 MK IIICDT 30 S MK IIICDT 40 S MK IIICDT 60 MK IIICDT 90 MK III(see separate data sheets)

Model CDT 40 MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 18.4 l/dDehumidification – 30°C & 80% RH 43.5 l/d Air volume 350 m³/hPower supply 230 V/50 HzMax. ampere consumption 4.1 AMax. power consumption 0.9 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 57 dB(A)Water container capacity 14 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 40 kg

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS



CDT 40 MK II

ohr

93699.24g

BEND RADII:

24-05-2012

SCALE: NOT TO SCALE 351191

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191


CDT 40 MK II

8






740

825

540

545


CDT 40 MK II

ohr

93699.24g

BEND RADII:

24-05-2012


MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO



CDT 40 MK II

8






740

825

540

545


CDT 40 MK II

ohr

93699.24g

BEND RADII:

24-05-2012


MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO



CDT 40 MK II

8






740

825

540

545

0

5

10

15

20

25

30

35

40

0,00 0,50 1,00 1,50 2,00 2,50

°C

L/H

40% 60% 80%


823

736

539

542

01.2

0

dantherm.com

Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable• Large wheels• On the back two Ø100 mm flex. air ducts may be connected

(max. length of 5 m) (accessory)• Built-in 1 kW heating element• Supplied with high pressure fan



FunctionThe CDT 40S MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.


CDT 40S MK IIIMOBILE DEHUMIDIFIER

FEATURES



CDT 40S MK III


01.2

0

dantherm.com


Accessories½” drain outletRemote hygrostatWall bracketRemote monitoring (IMCS)Condensate pump in a cassetteFlex. air ducts Ø100 mm(see separate data sheet)

Also available in this series:CDT 30 MK IICDT 30S MK IICDT 40 MK IICDT 60 MK IICDT 90 MK II(see separate data sheets)

Model CDT 40S MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 18.6 l/dDehumidification – 30°C & 80% RH 43.5 l/d Air volume 560 m³/h*Power supply 230 V/50 HzMax. ampere consumption 8.4 AMax. power consumption with heating element 1.9 kWMax. power consumption without heating element 0.9 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 58 dB(A)**Water container capacity 14 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 43 kg

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS



CDT 40 S MK II

ohr

93418.55g

BEND RADII:

24-05-2012


MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO



CDT 40 S MK II

8






740

825

540

542


CDT 40 S MK II

ohr

93418.55g

BEND RADII:

24-05-2012


MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO



CDT 40 S MK II

8






740

825

540

542


CDT 40 S MK II

ohr

93418.55g

BEND RADII:

24-05-2012


MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO



CDT 40 S MK II

8






740

825

540

542

0

5

10

15

20

25

30

35

40

0,00 0,50 1,00 1,50 2,00 2,50

°C

L/H

40% 60% 80%


*Measured without air ducts mounted.**Measured with air ducts mounted.

823

736

539

01.2

0

dantherm.com

Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels






FEATURES



CDT 60 MK III



01.2

0

dantherm.com



Also available in this seriesCDT 30 MK IICDT 30S MK IICDT 40 MK IICDT 40S MK IICDT 90 MK II(see separate data sheets)

Model CDT 60 MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 28.4 l/dDehumidification – 30°C & 80% RH 65.0 l/dAir volume 725 m³/hPower supply 230 V/50 HzMax. ampere consumption 5.6 AMax. power consumption 1.3 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 57 dB(A)Water container capacity 14 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 46 kg

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS


Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.

CDT 60 MK II

99141.12g

BEND RADII:

CDT 60 MK II

ohr

351193

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO


25-05-2012

SCALE: NOT TO SCALE

351 193

8






820

905

540

542


CDT 60 MK II

99141.12g

BEND RADII:

CDT 60 MK II

ohr

351193

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO


25-05-2012

SCALE: NOT TO SCALE

351 193

8






820

905

540

542


CDT 60 MK II

99141.12g

BEND RADII:

CDT 60 MK II

ohr

351193

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO


25-05-2012

SCALE: NOT TO SCALE

351 193

8






820

905

540

542

All dimensions are in mm

903

816

539

0

5

10

15

20

25

30

35

40

0,00 0,50 1,00 1,50 2,00 2,50 3,00 3,50

°C

L/H

40% 60% 80%


01.2

0

dantherm.com

Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser• Adjustable handle• Plastic bumpers• Low weight• Large wheels

Water drain• Fitted with a drain outlet for connection to a ½” water hose





FEATURES



CDT 90 MK III



01.2

0

dantherm.com


AccessoriesRemote hygrostatRemote monitoring (IMCS)(see separate data sheet)

Also available in this seriesCDT 30CDT 30SCDT 40CDT 40SCDT 60(see separate data sheets)

Model CDT 90 MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 37.0 l/dDehumidification – 30°C & 80% RH 86.5 l/dAir volume 1000 m³/hPower supply 230 V/50 HzMax. ampere consumption 8.3 AMax. power consumption 1.9 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 57 dB(A)Colour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel material PPControl panel material ABSWeight 62 kg

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS


ohr


CDT 90 MK II

355066.95g

BEND RADII:

23-12-2011


MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO



CDT 90 MK II

8






895

980

593

650

ohr


CDT 90 MK II

355066.95g

BEND RADII:

23-12-2011


MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO



CDT 90 MK II

8






895

980

593

650

ohr


CDT 90 MK II

355066.95g

BEND RADII:

23-12-2011


MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO



CDT 90 MK II

8






895

980

593

650

All dimensions are in mm

977

894

593

0

5

10

15

20

25

30

35

40

0,00 0,50 1,00 1,50 2,00 2,50 3,00 3,50 4,00 4,50 5,00

°C

L/H

40% 60% 80%


11.1

9

dantherm.com

ACCESSORIES CDT 30 - 40 - 60 - 90 MK III


Illustration Accessory Description CDT type Dantherm no.

Hygrostat When a hygrostat is connected the dehumidifier can operate continuously dependent on the relative humidity in the room.

Two versions are available:Hygrostat with 0.4 m cable, jack plug and fittingHygrostat with 3 m cable and jack plug

AllAll

396242 396241

½” draining tap and screwed hose connector

Ball tap, brass screwed hose connector and clamp for mounting on the water container.

All 396243

Intelligent Remote Monitoring and Control System (IMCS)

IMCS enables you to check the humidifying status in realtime from computers, smartphones and tablets. In addition, you can remotely monitor and control parameters such as power on/off, alarms, temperature and power consumption.

All Please contact sales for more information

Condensate pump in a cassette

Cassette with built-in condensate pump.

Vertical lift: up to 3 metresLength of tube: 10 metres

CDT 30/30S

CDT 40/40S/60

075616

075617

Wall bracket Using the wall bracket the dehumidifier can be hung on the wall.

CDT 30/30S

CDT 40/40S/60

396247

396248

CDT 30 MK III MOBILE DEHUMIDIFIER - Dantherm

Documents

Transcript of CDT 30 MK III MOBILE DEHUMIDIFIER - Dantherm