CCHAIN SAW ACCESSORIES - O.E.MHAIN SAW ACCESSORIES - O.E

Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M

C C

605-710 71752Air FilterFits ICS Concrete / Cut off Saw models:603GC, 613GC, 633GC and 680GC. Size: 3-7/8” OD X 2-3/8” ID X 3-1/4” HT. Same as our 605-709 except higher.

605-711 73336Pre FilterFor use with our 605-710 air filter. Fits ICS Concrete / Cut off Saw Size: 2-3/8” bottom OD X 2-1/16” top OD X 2-9/16” HT.

592-106 505375Crankshaft Bearing Fits ICS concrete saws, Size: 15mm (37/64”) ID X 35mm (1-3/8”) OD X 11mm (7/16”) HT. Bearing# 6202 - open both sides)

593-103 73209Crankshaft bearing Fits ICS models: 613GC, 633GC and 680GC; Size: 17mm ID X 40mm OD X 12mm HT.(Bearing# 6203/C3) Open both sides.

JONSEREDS605-173 501 80 71-01

501 80 71-05

Air Filter For Chain Saw model: 630

605-062 503 81 45-03Air Filter For chain saw models: 2063, 2071, 2163 and 2171. Nylon mesh style.Size: 3-5/8” L x 2-7/8” W x 1-5/8” HT.

605-060 537 02 40-03

Air Filter (Twist on) For chain saw models:2141, 2145, 2149, 2150 and 2152. Air filter attaches by simply twisting on the carburetor manifold. Note: Some 346 and 353 models use a steel snap to connect.

657-120 503 86 92-01

Anti Vibration Damping Fits chain saw models: 2147 and 2152.Measures: 11/16” L X 9/16” OD with a 3/16” ID.

646-154 503 74 44-01Clutch Assembly For chain saw models: 2063, 2065, 2163, 2165, 2071 & 2171. Measures: 3.057” OD X 0.471” Thick.

646-155 503 70 15-02

Clutch Assembly For chain saw models: 820, 830, 920, 930, 2094 & 2095.

Measures: 3.045” OD (77mm) X 0.542” (13.90mm) Thick.

646-113 501 77 85-01

Clutch Assembly Fits chain saw models: 625 & 630OLDER models.

Measures: 3.057” OD X 0.512” Thick.(10mm coarse thread).(Also see our 646-153 newer style under Husqvarna).

651-174 537 04 41-02

Chain AdjusterFor chain saw models:2163, 2165, 2171, CS2163,CS2165, CS2166, CS2171,CS2172, CS2186 and CS2188.

651-175 537 07 12-01

Chain Adjuster Assembly Found on model: 2159 chain saw.(Includes part#’s 503869101 and 503885401)

570-283 537 15 73-02

Cylinder Assy (47mm) Will also fit Jonsereds models: 2156 & 2159. (47mm X 1.5mm).

Displacement: 59cc; Stroke: 34mm. NOTE: If your cylinder is equipped with nipple on the cylinder base, decompression side. This was used to operate the automatic decompression valve. You will need to replace this old automatic with a manually decompression valve. (Order# 570-003). Includes: cylinder, piston and ring, piston pin and clips. Gasket and Decompression Valve NOT included.

570-286 503 69 10-73503 93 90-03503 93 90-05503 53 90-71503 93 90-71503 93 90-72

Cylinder Assy (48mm) Fits chain saw models: 2065 and 2165.

Note: Decompressionvalve NOT included -Comes with threadedplug only.

2156 / 2159

2065 & 2165

ICS JONSEREDS continued

16-30

Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M

C C

570-287 503 62 64-72503 62 64-73503 93 90-05503 93 93-71503 93 93-72503 96 52-71

Cylinder Assembly (50mm) Fits chain saw models: 2065, 2071, 2165 and 2171.

570-271 506 15 55-06

Cylinder Assembly (56 mm)Fits chain saw models:2095 / 2095 Turbo.

NOTE: You will need to order 1) 570-001 plug for thedecompression hole andre-use the original bakelitebase plate.

572-735 503 90 73-71

Piston Assembly (42mm)Fits chain saw model: 2145.

572-801

Piston Assembly (44mm) Fits chain saw model: 2050.

572-704 503 60 81-01503 60 81-71


572-706 503 92 04-71537 21 96-02


Note: Older model chainsaws have a crankshaft connecting rod with smaller (13mm bore). This piston fits a 15mm connecting rod. Replaces 503 92 04-71 before SN 020700001.

572-705 537 15 72-02

Piston Assembly (47mm) Fits chain saw model: 2059 and 2159.

2071 & 2171

2095

(While Quantiities Last)

572-499 503 53 90-02

Piston Assembly (48mm) For chain saw models:625 and 630. Direct replacement for the original (48mm) bore Jonsereds cylinder assembly.

572-714 503 69 13-71

Piston Assembly (48mm)Fits Chain Saw models: 2065 & 2165. (replaces our old# 572-806)

572-524 501 65 94-03

Piston Assembly (50mm)For model: 670.

572-718 503 28 90-42503 69 12-71503 69 14-71503 93 92-71

Piston Assembly (50mm) Fits Chain Saw models: 2071 and 2171.

572-807 501 65 88-03

Piston Assembly (50mm) Fits chain saw model: 670. Includes: Piston, Piston pin, Retainer clips and ring.

572-715 503 60 98-02503 60 98-03

Piston Assembly (52mm)Fits chain saw model: 670. NOTE: For 50mm piston assembly see our 572-807.

572-717 537 16 98-71

Piston Assembly (54mm) Fits chain saw model: 2186. Note: Piston Rings = 1.2mm thick

572-721 503 46 02-02

Piston Assembly (56mm)Fits chain saw models:2094 and 2095. Overall Height = 49mm, (1mm) higher then our 572-722Note: Piston rings = 1.5mm thick

16-31

JONSEREDS continued JONSEREDS continued


C C

572-722 537 13 76-71

Piston Assembly (56mm)Fits chain saw models:2094 and 2095. Note: Piston Rings = 1.2mm thick

574-206 503 28 90-02Piston Ring Set (40mm X 1.5mm)Fits chain saw model: 2040.

574-212 503 28 90-05Piston Ring Set (42mm X 1.5mm)Fits chain saw model: 2045.

574-230 503 28 90-29Piston Ring Set (47mm X 1.5mm) Fits chain saw model: 2063 & 2163.

574-232 501 20 56-02 503 28 90-15

Piston Ring Set (48mm X 1.5mm).Fits Jonsereds chain saw model: 630.Note: Some applications use one only piston ring.

574-157 501 20 56-02503 28 90-15

Piston Ring only (48mm X 1.5mm) Fits chain saw model: 630.For our 572-499 piston assembly.

574-264 1128-034-3000

Piston Ring Set (50mm X 1.2mm)Fits chain saw models: 371 EPA and 372 EPA.(Priced and Sold in sets)

574-137 503 28 90-17

Piston Ring only (50mm X 1.5mm)Fits chain saw model: 670.For our 572-524 piston assembly.

574-266 1122-034-3001

Piston Ring Set (54mm X 1.2mm)Fits some chain saw model: 385.(Priced and Sold in sets)

574-254 503 28 90-22

Piston Ring Set (54mm X 1.5mm) Fits chain saw model: 2083.

570-003 503 71 53-01

Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Overall Length: 1-7/16” - Blue knob with 2 holes in nut.

570-005 503 665 601

Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Fits Husqvarna, Jonsereds and Partner models: K1250 etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut. Similar to our 570-003 but with a longer main body.

623-820 501 51 22-02

Head / Base GasketFits models: 630 and 670.

623-822 503 96 15-01

Head / Base Gasket onlyFits chain saw models: 362, 365, 372, 372 and 375; also fits Jonsereds models: 2065, 2071, 2162 and 2171.

640-243

Gasket SetFits chain saw model: 630. (Includes oil seals)

551-107 501 56 45-01Fuel CapFor chain saw models: 625, 630 and 670.

600-185 503 90 14-01941 14 60-1

Electronic IgnitionFor chain saw model: 630

600-164 501 51 61-01 /501 51 61-02501 61 75-01

Electronic Ignition Fits chain saw models:625, 630 and 670.The electronic ignitioncomponent is connectedwith the ignition coil toachieve full ignition.This type of ignition module utilizes transistor switches for magnet activation.

600-165 501 61 72-01

Ignition Coil / ModuleFits Jonsereds chain saw models: 625, 630 & 670.

610-040 363400Fuel Filter - FeltFuel Filter found on many Jonsereds chain saw models. Measures: 3/4” L X 1/2” ID X 3/4” OD

16-32



C C

560-191 501 55 14-02

Starter HandleFor most Jonsereds Chain Saw models.

625-400 501 52 04-01Starter Spring For chain saw models: 625, 630, Super & 670.

625-450 504 21 26-01

Starter Spring For chain saw models: 66E, 70E, 80, 90, 111 Super, 621, 801, 910E, 910EV and 920.

625-451 504 21 26-02

Starter SpringFor chain saw models: 49SP, 50, 51, 52, 52E & 521EV.

625-455 504 21 26-06

Starter Spring For chain saw models: 450, 455, 510SP, 520SP, 525 and 535.

625-325 507 10 00-73

Starter Spring For chain saw models: M36, 361, 361E, 365, 370 and 380.

625-426 505 29 51-26

Starter Spring For chain saw models: 490 and 590.

625-404 501 76 31-01

Starter SpringFor chain saw model: 2041.

Note: Will work on Husqvarna chain saw models: 340, 345, 346, 350, 351, 357, 359 if you re-use the original starter spring case - You will have to make a slight adjustment to the outside spring hook. (This spring is NOT an exact replacement for the Original Husqvarna# 537 09 31 01)

625-430 503 43 19-01

Starter Spring For chain saw models: 2077,2083 Turbo and 2095.Spring is in a plastic cage,Spring OD = 73mm (While Quantities Last)

(Sold in multiples of 10)

625-408 537 10 93-101Starter Spring For chain saw models: 2149, 2159, CS2141, CS2145, CS2150, CS2152, CS2153, CS2156 and CS2159.Spring is in a plastic cage,Spring OD = 67mm / 2-5/8” approximately.

636-145 503 76 53-01

Muffler / Exhaust For chain saw models: 2063, 2065,2071, 2163, 2165 and 2171. Exhaust mounting holes are 53mmcenter to center. This muffler is a NON DF version NOT US Forest Service approved. (Also see our 636-143)

636-143 503 76 53-02503 76 54-02

Muffler / Exhaust For chain saw models: 2063, 2065, 2071, 2163, 2165 and 2171. Exhaust mounting holes are 53mm center to center. Comes with spark arrester. (Also see our 636-145)

636-148 503 71 13-07

Muffler / ExhaustFits chain saw models: 2094 & 2095. Mounting bolts holes are on 52mmcentres. NOTE 1: This muffleris a NON DF version NOT US Forest Service approved. (Also see our 636-149) Front and back images shown for reference

636-149 503 71 13-04

Muffler / ExhaustFor chain saw models: 2094 & 2095. Mounting boltsholes are on 52mm centres. Note: Complete with spark arrester screen. (Also see our 636-148). Front and back images shown for reference.

705-574T-WrenchFits chain saw models: 510, 525, 530, 535, 630,670 and most other Jonsereds models.Size: A= 7”, B= 1”, C= 1”. Bar= 1/2” (13mm),Plug= 3/4” (19mm)

16-33



C C

705-600T-WrenchFits chain saw models: 77, 90, 621, 820 and 920.Size: A= 7”, B= 1-1/8”, C= 1-1/8”. Bar= 19/32” (15mm), Plug= 3/4” (19mm)

For MAKITA - See DOLMAR / MAKITA

McCULLOCH605-204 214224 / 216905

61460 / 91460Air Filter Fits models: 110, 120, 130, Mini Mac and Eager Beaver. Size: 2” OD X 7/8” HT

605-339 213883 / 215803300385

Air Filter Fits Chain Saws and Blowers. Models: 300 and 385. Felt with rubber seal. Size: 4” L X 2-13/16” W

605-215 89072 / 92410Air FilterFits Chain Saw model: 510 Size: 3-1/4” L X 3-1/4” W

605-253 68685 / 91458

Air Filter Fits chain saw model: Power Mac. Size: 3” L X 2-1/4” W

605-261 215681 / 85387

Air FilterFits chain saws models: 800, 805 and 850 Size: 5-3/8” L X 5-1/8” W

605-246 21668569922 / 92420

Air Filter Fits chain saws models: 10-10 and 700 series Size: 4-3/8” L X 4-1/8” W

605-212 215456322001 / 94970

Air FilterFits chain saws models: 310, 320, 330& Eager Beaver 2.1 Size: 3-3/16” L X 2-11/16” W

605-238 214226 / 95213

Air Filter Fits chain saws models:600, 610 series andEager Beaver 3.7 (Raised centre) Size: 4-3/8”L X 4-1/4” W

670-104 110676Bar NutFor chain saw model: Mini- Mac 600 series. Size: 1/4”-28

670-105 120029Bar Nut For chain saw model: Mini Mac 300 series. Size: 6.3mm X 1.0 thread

670-101 213169Bar NutFits McCulloch models:600, 605, 610 and 650.Size: 8mm X 1.25 thread. For 13mm T-wrench

651-141

Chain Adjuster For McCulloch chain saw model: Mac 6.

651-243 110907 / 6865684929 / 90658

Chain Adjuster For chain saw model: Mini Mac 100 and 300 series

651-399 102115 / 105603110590 / 11095091982 / 94362

Chain Adjuster For chain saw model: 600 series.

621-120 83223Clutch Spring For chain saw models: 10-10, Mac 7-10, 55, 60 and SP 81.

621-121 51468AClutch Spring For chain saw models: Super 250 and Super 550.

610-048 63932Fuel FilterFound on many chain saw models. Made of felt. Measures: 1” L X 3/4” OD


(While Quantities Last)

16-34

JONSEREDS continued McCULLOCH continued


C C

613-601 21698549422 / 93720

Fuel Filter - In TankFor all McCulloch Mini Chain Saw and Trimmer models using 3/32” thru 1/8” ID fuel lines.Measures: 1-1/4” long X 1/2” diameter.

610-238 215708301011 / 64848

Molded FuelLine for chain sawmodel: 10-10. Measures: 6-1/8” overall length

600-935 Walbro# AM-35

Electronic ModuleFor chain saw models: Eager Beaver and Super Airstream V. (Original WALBRO module) (Made by SEM / WALBRO)

502-119 Phelon# 08133-04

Coil and Core (Armature)For chain saw models: MINI. For older style with points & condensor. (Original PHELON coil) (Made in the U.S.A.)

550-111 89322Fuel CapGas Cap for chain saw models: Pro 10-10 and Pro Mac 60 series.

551-111 87270

Oil CapFor chain saw models: Pro 10-10 and Pro Mac 60 series.

625-200 51665Starter SpringFor chain saw models: 1-40, 50,60, 70, 80, 200, 300, 400, 500, 600, 700, 800, D-44, PM-105, SP-125, 550 and Super 797.

625-201 68626

Starter Spring For chain saw models: Mac 1-10, 2-10, 3-10, 4-10, 5-10E, 6-10, CP 55, 70, 10-1C and 52-10A.

625-202 83078Starter SpringFor chain saw models: Mac 110, 115, 120, 130, 140, Mini Mac 6, 25, 30, 35, Power Mac 6, Pro Mac 55, 510, Super Pro 40, 310, 320, 330, 340 & Titan 7.

625-203 83334 / 87680Starter Spring For chain saw models: Pro Mac 10-10, 55, 60, 555, 570, 610, 650, 700, 800, 805, 850, 1010S, 5700, 8200,Super Pro 60, 70, 80, 81 and Model 7-10A.

625-427 32107

Starter Spring For chain saw model: 1000.

705-517

T-WrenchFits McCulloch chain saw models:1010 series, Pro Mac 555, 700, CD70,110, 120, 130, 140, 1600, Titan 50, 57,PM-6 and Double Eagle. Size: A= 7”, B= 1-1/2”, C= 1-3/8”. Bar= 1/2” (13mm), Plug= 5/8” (16mm).

OLEO MAC 625-675 50 00132Starter Spring For chain saw models: 250, 251, 251E, 251 Super, 252, 254 and early model 264.Note: Comes in a plastic case not shown

625-676 40 0013240 95034

Starter SpringFor chain saw models: 234, 240, 241, 244, 264F - Deluxe, 350, 355A, 935D, 941, 942, 945, 946, 950, 951 & 970.

625-500 60 0013261 00963

Starter SpringFor chain saw models: 260, 261, 271, 272, 284, 460AS, 480AS, 481, 482 and 482 MP.

PARTNER605-338 506 22 42-01

531 03 14-97

Air FilterFits Concrete / Cut-off Saws models: K650 Active and K700 Active. Size: 4-3/4” L X 3-3/8” W X 2-1/8” HT.Note: Top and Bottom images shown for reference.(For Pre Filter see our 605-239).

16-35

McCULLOCH continued McCULLOCH continued


C C

605-239 506 22 63-01 / 999810Pre filterFits chain saw models: K650 Active and K700.(3) layer foam filterSize: 7-7/8” L X 4-1/2” W X 3/4” HT

605-378 544 18 16-01

Air FilterPanel Air filter for Concrete / Cut Quik Saw model: K750. (For use with our 605-377 pre filter)Base Size: 4-15/16” L X 4-1/2” W X 1-3/8” HT.

605-377 506 36 71-01Pre filter For Concrete / Cut Quik Saw model: K750. (For use with our 605-378 air filter) Size: 7-5/64” L X 5-1/2” W X 13/16” HT.

605-440 506 23 19-01506 25 59-32

Pre Filter(3) Layer foam filter. Fits chain saw models:K950 Active & K960 Cut Quik saws. Size: 10-3/8” L X 5-1/4” W X 3/4” HT approx.(Also see our 605-438 Air Filter)

605-438 506 23 18-01506 23 18-02

Air FilterFits chain saw models: K950 and K1250 Active Cut Quik saws. Size: 6” L X 4-1/8” W X 2-5/8” HT

605-414 506 34 70-02

Air FilterFits Husqvarna and PartnerConcrete Saw / Cut Quik sawmodles: K950 and K960.Size: 6” L X 4-1/8” W X 2-1/2” HT

605-280 506 26 87-01

Pre filterFits Concrete / Cut Quick Saw models: K1250. (3) layer foam filter.Size: 10-5/32” L X 6-1/2” W X 13/16” HT.

605-400 510 24 41-01510 24 41-03

Air FilterFits Husqvarna and PartnerConcrete Saw / Cut Quik sawmodels: K970 and K1260.Size: 5-3/4” L X 4-1/4” W X 3-3/8” HT.

875-724 506 07 05-03Drive belt (cogged)For concrete / cut quick saw model: K950 with 12” and 14” blades. Size: 3/8” W X 34-1/2” L

875-712 506 29 67-02 544 90 84-02

Drive belt (multi rib)For concrete / cut quick saw model: K750. Size: .551” W X 32” L (6 rib, polyester cord construction)

875-725 506 07 05-04 506 34 74-24

Drive belt (cogged)For concrete / cut quick saw model: K950 Active with 16” blades. Size: 3/8” W X 36” L

875-711 506 03 30-31 506 27 67-41

Drive belt (cogged)For concrete / cut quick saw model: K650 Active, K650 Active II and K700 Active II Size: 1/4” W X 31-1/2” L

875-713 506 07 05-06Drive belt (cogged)For concrete / cut quick saw model: K650 Active III andK700 Active III cut off saws. Size: 3/8” W X 31-1/2” L

875-726 506 07 05-07Drive belt (cogged)For concrete / cut quick saw model: K1250 Active cut off saws. Size: 3/8” W X 39-1/2” L

670-101 503 22 00-01Bar NutFits chain saw models: R16, S50, S55, P55, P70 and P100. Size: 8mm X 1.25 thread. For 13mm T-wrench

651-142 230902 / 267650Chain AdjusterFor chain saw models: R16, S50, S55, P55, S65, P70 and P100.

621-127 294112Clutch SpringFor chain saw model: R16.

621-156 505 29 31-66Clutch SpringFor chain saw models: 400, 500 and 5000.

621-115 503 14 51-01Clutch Spring For models: 281, 288, 3120, 334T, 335XP, 336, 338, 339, 385, 390, 394, 395, K960 and K1250. Overall Length: 1-1/8” X 7/16” OD.


16-36

PARTNER continued PARTNER continued


C C

570-268 506 09 92-12

Cylinder Assembly (50mm)Fits concrete saw models: K650 (newer style), Super MKII, K700, 700 Active I, II and III.

570-300 506 38 61-71520 75 73-02520 75 73-04

Cylinder Assy (50mm)Fits concrete / cut quik sawmodels: K750 and K760.

NOTE: Also see our 570-270and 570-273 P&C Assemblies.

570-270 520 75 73-04581 47 61-02

Cylinder Assembly (51mm)Fits Partner / Husqvarna concrete / cut quik saw models: K750 and K760(Before February 2013).

570-273 581 47 61-03

Cylinder Assembly (51mm)Fits Partner / Husqvarna concrete / cut quik sawmodels: K760.(After February 2013).

Note: Decompression valve NOT included.

570-271 506 15 55-06

Cylinder Assembly (56 mm)Fits concrete / cut quik saw model: K950.

570-267 544 93 56-02 544 93 56-03

Cylinder Assembly (56mm)Fits concrete saw models: K960 and K970.

Note: Decompression valveNOT included.

K650 Cut off

K750 / K760

K750 / K760

K760

K950

K960 & K970

570-269 506 29 42-71 / A576 27 00-03

Cylinder Assembly (60mm) Fits concrete / cut quik saw model: K1250

572-463 505 34 07-82

Piston Assembly (48mm)For chain saw model: P650 and Partner concrete saw model: K650 (old style). Includes: domed piston and rings, piston pin and clips.

572-511 506 09 90-01

Piston Assembly (50mm)For concrete saw model: K650 (new style).

572-902 506 37 24-01506 37 24-02506 37 24-03

Piston Assembly (51mm)Fits concrete / cut quik saw models: K750 and K760.

NOTE: Fits K760 models manufactured prior to February 2013.

574-232 505 26 60-48

Piston Ring Set (48mm X 1.5mm).Fits Partner chain saw model: P650and Partner concrete saw model: K650 (old style).

574-157 505 26 60-48Piston Ring (48mm)For chain saw model: P650 and Partner concrete saw model: K650 (old style)

574-137 503 28 90-17Piston Ring (50mm)For Partner concrete saw model: K650 (newer style).

570-002 503 66 56-01503 71 53-01

Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Fits models: K650 and K700, Active I, II, III. Overall Length: 2” - Black knob with 1 holes in nut. Similar to our 570-004 but with different knob. (For plug only see our 570-001)

K1250


16-37



C C

570-005 503 66 56-01Decompression Valve (Blue Knob) For Chain Saw and Concrete saw cylinder assemblies. Fits Husqvarna, Jonsereds and Partner models: K1250 etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut. Similar to our 570-003 but with a longer main body.

640-323Gasket SetFor chain saw models: 500, 5000& 5000 Plus. (Includes oil seals).

640-360 506 38 53-05

Gasket SetFits Husqvarna / Partner cut quit / concrete saw models: K750 and K760.(Includes oil seals)

640-182Gasket SetFits Chain Saw model: K-650 Active

640-186Gasket SetFits Husqvarna / Partner cut quit / concrete sawmodel: K950.(Includes oil seals).

623-868 503 49 10-02503 49 10-01

Head / Base Gasket Fits Chain Saw model: P650 andConcrete Saw models:K-650 (both old and new), K700 Active I, II, III.

623-751 506 37 67-01

Head / Base Gasket For cut quik / concrete saw models: K750 and K760.

623-499 506 15 82-01Head / Base Gasket For cut quik / concrete saw models: K950.

591-101 302333Bearing - Piston Fits Chain Saw models R16, S50, P650 and Partner K650 concrete saw. (Size: 12mm X 16mm X 13mm)

551-116Oil CapFor chain saw models: R16, S50, S55, P55 and P70. Made of aluminum with screwdriver slot on top.

550-109 506 25 59-32Fuel Cap For chain saw and concrete / cut quik saw models: K650 and K950.

650-122 340722Sprocket Cover Partner Cover for chain saw models: R16, S50, S55, P55 and P70. Cast aluminum cover (yellow)

625-426 505 29 51-26

Starter SpringFor chain saw models: 500, 5000 and 5000 Plus.

625-427 505 29 51-08295108

Starter SpringFor chain saw models: R16, 18, 22, 30, 40, F55, K16, 20, 65, 650, 850, 1200, P55, 70, 100, 7000.

625-325 504 35 27-05Starter Spring For chain saw models: MINI P, P2, 3, 4, 330, 340, 350, P11 and P12.

625-429 506 25 89-01

Starter Spring For Partner / Husqvarna Concrete Saw / Cut Quik Saw models: K750, K760, K960 and K970.(Replacement starter spring for our 655-250 starter assembly).

655-250 506 38 56-12

Starter Assembly For concrete / cut quik saw model: K750. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, handle etc. Just needs to be bolted on

16-38



C C

605-040 530 05 79-25

Air Filter - Felt.Fits chain saw models: P3314,P3314WS, P3314WSA, P3416,P3516PR, P4018, P4018WM,P4018WT, P4018WTL, PP3516, PP3816, PP4018, PP4218, PPB3416, PPB4018, PPB4218, S1970 and Type1 Size: 3-7/16” L X 2-5/8” W X 3/16” Thick.

605-087 530 057869

Air FilterFits chain saw models: P3818AV, P4018AV, PP3516AVX,PP4218AV, PP4218AVHD, PP4218AVL,PP4218AVX, SM4218AV, SM4218AVX.Size: 3” L X 3-1/4” W X 3/16” HT.

605-428 23791530 023791

Air FilterFits chain saw models: Micro XXV, Micro 25, 180, 200, 205, 225, 235, 236, 1800, 2000, 2100, 2300, 2350 and 2400. Size: 2-5/8” L X 1-1/2” W X 1” HT

605-436 23369530 023369

Air FilterFits chain saw models: 25 and 25DASize: 3-3/8” L X 1-5/8” W X 1-1/4” HT

605-410 2586530 002586

Air FilterFits chain saw model: 361 Size: 4-1/8” L X 3-1/2” W

605-515 530 037793

Air Filter Fits chain saw models: 1950, 2050, 2075, 210, 2150, 2175, 2250, 230, 2450, 2550, 260, Pro 221, 221LE, 2375, Wild Thing, 1900, 2350, 2055, 220, 225 and Woodsman. Size: 3-1/4” L X 2-1/2” W X 3/4” HT

605-091 575 29 63-01

Air FilterFits chain saw models: PP5020AV.Size: 2-7/8” L X 3” W X 7/8” HT.

605-486 036141530 036141545 057701

Air FilterFits chain saw models: 2200, 2500, 2600, 2700, 2750, 2775, 2900, 3050, PP4620AVHD, PP4620AVL and Poulan Pro 255, 295, 310 and 315.Size: 3” L X 2-3/4” W X 7/8” HT

605-402 24548 / 20913530 024548952 014129

Air FilterFits chain saw models: 3400 and 3700. Size: 3-7/8” L X 2-5/8” W X 1” HT

646-129 93919ClutchFor many small Poulan chain saw and Poulan / Weedeater Trimmer models. Measures: 2-3/8” OD, steel washer included.

621-132Clutch SpringFor chain saw models:201, 221, 361, 401 and 451.

651-150 530 015134530 015135530 016115530 023492

Chain AdjusterFor chain saw models: Micro XXV, Micro XXV Deluxe, Micro 25, Micro 25 Deluxe, 1800 2000, 2300 and 2350.

651-151 15134 / 15135 / 23492530 015134530 023492530 016115

Chain Adjuster For chain saw model: 250.

651-375 15385 / 23064530 015385530 023064

Chain AdjusterFor chain saw models: 3400 and 3700.

651-377 069611530 069611

Chain AdjusterFor chain saw models: 210, 230, 260, 2050, 2075, 2150, 2175, 2250, 2450 and 2550.

610-022 23364530 091878

Fuel Filter Replacement felt filter for our 610-014 in-tank fuel filter. Fuel Filter for many Poulan chain saw models. Measures: 1” Long X 1/4” ID X 9/16” OD.

610-030 34032530 034032

Fuel FilterReplacement felt filter for our 610-006 in-tank fuel filter. Fuel Filter for many Poulan chain saw models. Measures: 1” Long X 7/16” ID X 13/16” OD.




16-39

POULAN continued POULAN continued


C C

610-345 530 023166 530 026119

Duck Bill Valve For Homelite chain saw models XL, XL-2 and Super 2. Duck Bill Valve - Fits Homelite Trimmers and Chain Saws. Measures: .100” ID X .201” OD X .25” L

125-245 530 014347 / 952 701583530 010729 / 952 701567

Gas CapFor chain saw models: 180, 190, 1800, 185, 2000, 2300AV, 2300CVA,2350CVA and 5500.Measures: 1-1/2” diameter.

550-151 530 071266501 819602

Fuel CapFor chain saw models: 234, 238 & 365.

600-915 Walbro# MA-15

Electronic Ignition ModuleFor Poulan / Weedeater chain saw “CSI” models. (Original WALBRO / SEM module)

610-034 530 023877

Fuel Line FittingFits chain saw models: 180, 1800, 180C, 1800 Super, 190, 2000, 210, Micro XXV and S23. Arbor Pro gas saws.

610-032 530 010897 / 530 014362 530 014815 / 530 023364 530 047004530 095643 530 095646 530 095649

Fuel FilterFits chain saw models: 2025, 2050, 2350, 2775 & FL 1500. Size: 9/16” OD X 1-5/8” L.

660-060 530 069957530 071259

Oil Pump Fits chain saw models: 1950 thru 2550, 211, 220 & 260 Pro.

560-368 530 06931369313

Starter PulleyFits chain saw models: 2200, 2500, 255, 2600, 2750, 2900, 295, 3050, 310, 315. Starter Pulley for Poulan saws -Dealers have used it on Husqvarna model 41 Chain Saw. May fit other Husky saws? (4) cog pulley. NOTE: original Husky application is (6) cog.

145-516Starter Rope AssemblyFor chain saw models: 25D and also 180 and 190. Rope length 21”, plastic knob fastened to rope end.

625-152 530 04201242012

Starter SpringFor chain saw models: 245, 305, 306, 345, 2000 and 2300

625-442 530 027531Starter SpringFor chain saw models: 2025, 2050, 2075, 210, 2150, 2175, 2250, 230, 2350, 2450, 2550 and 260, 285, 295, 305, 310, 315 and 335

625-157 530 04205142051

Starter Spring For chain saw models: 3400 and 3700. Starter Spring for Sears / Roper / AYP chain saw models: 358-354810, 358-354830 (3.4, 3.7 CU. IN. Poulan)

625-101 4262

Starter SpringFor Lombard chain saw models: 42 series, Lightning and Comango. Starter Spring for Poulan chain saw models: 360, 361 and 400.

REMINGTON605-523 66241Air FilterFits chain saw model: Mighty Mite (Large version). Made of felt material. Size: 3-9/16” L X 3-1/4” to 4-1/16” W (bottom)

605-553 65071Air FilterFits chain saw model: SL9 and SL9 deluxe. Made of felt material. Size: 3-5/8” L X 3-5/8” W.

560-101 60832Starter Dog / Starter Pawl. Found on many older Remington chain saws using an aluminum starter cup. Remington models:PL-4, SL-4A, Bantam etc.Size: Dog width: 1/2” with a 3/8” ID.


16-40

POULAN continued POULAN continued


C C

541-103 1108-140-1000Air filter capFits chain saw models: 08 and 08S. (For use with our 605-708 air filter)

605-719 1120-120-16001120-124-0800

Air filter Fits chain saw model: 009, 010, 011. Size: 3-7/8” L X 2-5/8” W

605-717 1130-124-0800Plate filter Fits chain saw models: 017, 018, MS170 and MS180. Size: 3-1/2” L X 2-9/16” W approximately.

605-724 1132-124-0800

Air FilterFits chain saw models:019T, MS 190T and MS 191T.Size: 3” L X 3” W X 1/16” HT.

605-721 1139-124-0800

Air FilterFits chain saw model: MS171.Size: 4-1/8” L X 2-3/4” W X 1/4” HT.

605-723 1139-120-1602

Air FilterFits chain saw models:MS 171, MS 181 and MS 211.Size: 4” L X ____” W X 3/4” HT.

605-718 1137-120-1600

Air FilterFits chain saw model: MS192 T.Size: 4” L X 2-1/2” W X 5/8” HT.

605-720 1129-120-16021129-120-16051129-120-16061129-120-1607

Air FilterFits chain saw model: MS 020 T and MS200 T.Size: 3-1/2” L X 2-3/4” W X 5/8” HT.

605-722 1145-140-4400

Air FilterFits chain saw model: MS 201 T.

Size: 4-7/16” L X 3” W X 3/4” HT.

560-102 Starter Dog WasherThis is a fibre washer used on olderFairbanks Morse, Remington chain saws thatused a starter dog assembly and aluminum starter cup.

SEARS / ROPER / AYP605-907 9163HAir FilterFits AYP / Sears/ Roper Chain Saw. Sears model 3.7 cubic inch Size: 3-7/8” L X 3-5/8” W

625-157 42051Starter SpringFor chain saw models: 358-354810, 358-354830 (3.4, 3.7 CU. IN. Poulan)

FOR SACHS DOLMAR - SEE “DOLMAR /

MAKITA” SECTION.SHINDAIWA605-319 38010-82581

Air filter Fits Cut off saws, models: EC7500 and EC7600. (includes foam pre filter)Size: 7” L X 4” W X 2” HT

625-900 22104-7530022104-75310

Starter SpringFor chain saw models: 305, 345, 346, 350, 355, 405, 406, 407, 410, 415, 416,440, 450, 451, 480, 485 and 500.

625-901 22100-75310

Starter SpringFor chain saw models:415 and 450 (older models)

STIHL605-708 1108-120-1600

Air FilterFits chain saw models: 08 and 08S


16-41

REMINGTON continued STIHL continued


C C

605-687 1123-120-16131123-120-1612

Air FilterFits Chain Saw models: MS210, MS230 and MS250.

Size: 3-5/8” L X 1-3/16” W X 1-3/8” HT.

605-727 1141-120-1600

Air FilterFits chain saw models:MS231, MS251, MS271,MS291, MS311, MS362C and MS391.Size: 3.08” OD X1.675” Bottom opening ID X 1.7” Height.

605-741 1121-120-1617

Air Filter Fits chain saw models:024, 026 (new style),MS240 and MS260with a standard styletank vent.

“For chainsaw models that DO have the carburetor compensator”.Size: 3-1/8” L X 3-1/2” W X 1-1/4” HT approximately. (Top and Bottom pictures shown (1) air filter only)

605-740 1121-120-1612

Air FilterFits chain saw model: 026 PRO.

“For chainsaw models that DO NOThave the carburetor compensator”.

Size: 3-1/8” L X 3” W X 1-1/4” HT approximately.

605-745 1140-140-4401

Fits chain saw models: MS 311, MS 362 & MS 391.

Size: 4-3/8" L X 3-5/8" W X 1-7/8" HT.(Top and bottom images shown for reference.)

605-732 1133-120-1604

Air FilterFits chain saw model: MS270 and MS280.Size: 4” L X 4” W X 1-11/16” HT.

605-679 1127-120-16211127-120-1620

Air Filter Fits chain sawmodels: 029, MS290,MS310 and MS390.

Size: 4-9/16” L X 2-5/8” W X 1-1/2” HT. (Top and Bottom pictures shown (1) air filter only)

605-742 1135-120-1600

Air FilterFits chain saw model: MS341 and MS361.

Size: 4-5/8” L X 2-13/16” W X 1-11/16” HT.

605-733 1118-120-16101118-120-16111118-120-1615

Air Filter Fits chain saw models:028, 028 Super and 028 Wood Boss.Size: 3-1/2” L X 2-1/4” W X 3/4” HT

605-753 1125-120-16151125-120-1620

Fits chain saw models: 034, 034 Super and 036.

NOTE: Fits older 034 chainsawsbefore serial number 1 45 945 205. Fits older 036 chainsaws before serial number X 32 622 639. This fi lter doesn’t have the compensator hole, and is too narrow for newer models 034 & 036. Please verify serial number fi rst before purchasing.Size: 3-1/4” L X 2-7/8” W X 1-1/8” HT

605-736 1125-120-1626

Fits chain saws models:034 and 036.

NOTE: Fits newer 034 chainsawsafter serial number 1 45 945 205.Fits older 036 chainsaws after serial number X 32 622 639;also found on models: MS340 and MS360.This fi lter has the compensator hole, and is too wide for older models 034 & 036. Please verify serial number fi rst before purchasing.Size: 4-1/8” L X 3-5/8” W X 1-5/8” HT.

606-138 1119-140-1903 1119-140-1905

Air filter cover

Aftermarket box cover for chainsaw model 038 series.

This plastic piece often takes most of abuse from day to day use and fadesin colour. Includes attachment nut and mesh screen.

605-073 1119-120-1630

Air FilterFits chain saw model: MS381.

Size:4-1/8” L X 3-1/16” W X 15/16” HT.

16-42

STIHL continued STIHL continued


C C


16-43

605-691 4201-141-0310

Air Filter Wrap Fits Concrete / Cut off Saw models: TS350, TS360 and TS510 / TS760. Felt wrap with stitched elastic for tight seal. (Pre filter for our 605-709)

605-055 4201-140-1802

Inner Air Filter Fits Concrete / Cut off Saw model: TS360. Inner filter - centre bolt mount style.(Inner filter for our 605-709)

605-336 4223-141-0300

Air FilterFits Concrete / Cut off Saw model: TS400 (air filter). Size: 5-3/8” L X 3-3/8” W X 1-15/16” HT. (Paper element with soft foam seal)

605-332 4223-140-03004223-140-1800

Air FilterFits Concrete / Cut off Saw model: TS400 (secondary filter). Size: 4-5/8” L X 2-11/16” W X Pipe: 1-1/8” OD X 7/8” HT

605-337 4223-141-0600Air Filter Fits Concrete / Cut off Sawmodel: TS400 (pre filter). Size: 5” L X 3-1/8” W X 13/16” HT, Centre hole 5/16”, Offset hole 3/16” ID. (3) layer foam

605-348 4221-140-44004221-141-0300

Air Filter Fits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (air filter). Size: 4-1/2” OD X 2-1/16” ID X 2-1/4” HT. (Use with our 605-343 & 605-346)

605-343 4221-140-1800Air Filter Fits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (inner filter). Size: 1-7/8” OD X 1-11/16” ID X 1-11/16” HT. (Use with our 605-348 and 605-346)

605-346 4221-141-0310

Air FilterFits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (pre filter). Made of felt material.(Use with our 605-348 and 605-343)

605-675 1110-120-1601

Air FilterFits chain saw model: 041. Made of wire mesh & felt material. Size: 4-1/4” L X 4-1/8” W

541-106 1110-140-9500

Air filter cap Fits chain saw models: 041, 051 and 070. (For use with our 605-675 / 605-676 / 605-686 air filters)

605-676 1111-120-1601Air FilterFits chain saw models: 051 and 076. Made of wire mesh & felt material. Size: 5” L X 4-1/4” W

605-683 1113-120-16021113-120-16031113-120-1612

Air Filter Fits chain saw models: 031 and 032. Size: 3-1/8” L X 2-5/8” W X 15/16” HT

605-735 0000-120-1653 / 0000-120-1654

Air FilterFits chain saw models: 044, 046, 064, 066, 088, MS440, MS441, MS460, MS640, MS650, MS660 and MS880. Felt cloth outer wrap with a foam filled interior. Designed for oil-less use. (Top and bottom images shown for reference.)Size: 4-3/16” L X 3-1/8” W X 1-3/4” HT

605-725 4201-140-1801

Air FilterFits Concrete / Cut off Saw models: TS350 and old style TS510 / TS760Inner filter - 2 bolt mount style(Inner filter for our 605-709)

605-709 4201-140-18054201-141-0300

Air Filter Fits Concrete / Cut off Saw models: TS350, TS350AVE, TS360, TS510 and TS760. Size: 3-7/8” OD X 2-3/8” ID X 2-7/8” HT (Also found on Sachs Cut off saws)


C C

605-692 4224-141-03004224-141-0300A

Air Filter Fits Concrete / Cut off Saw models: TS700 and TS800. Size: 5-1/2” L X 4-1/16” W X 1-3/4” HT. (Paper element with soft foam seal). Uses our 605-700 pre filter.

605-700 4224-140-1801Air Filter Pre Filter (secondary filter)Fits Concrete / Cut off Saw models: TS700 and TS800. Size: 4-5/8” L X 3-1/4” W X 9/32” HT. For use with our 605-692 air filter.

Filter Kit for TS350 & TS510605-800 4201-140-1801

4201-140-18054201-141-0300 4201-141-0310

Air Filter (3) Piece Kit Fits Concrete / Cut off Saw models: TS350 and TS510

Air Filter Kit for STIHL TS360605-810 4201-140-1801

4201-140-18024201-141-0310

Air Filter (3) Piece Kit Fits Stihl Concrete /Cut off Saw model: TS360

Air Filter Kit for TS400605-820 4223-007-1010 / 4223-140-1800

4223-141-0300 / 4223-141-0600

Air Filter (3) Piece Kit Fits Stihl Concrete / Cut off Saw model: TS400. Kit includes: (1) 605-336, (1) 605-332 and (1) 605-337

Filter Kit for TS460, TS760605-840 4221-007-1002

4221-140-18004221-140-44004221-141-0310

Air Filter (3) Piece Kit Fits Concrete / Cut off Saw models: TS460 / TS760

Filter kit for TS410 and TS420605-850 4238-140-1800

4238-140-44014238-140-44024238-141-03004238-141-300B

Air Filter (2) Piece Kit Fits Concrete / Cut off Saw models: TS410 / TS420. (Includes (1) 605-559 pre filter andpanel filter). The panel filter measures:5-3/4” L X 5-1/2” W X 1-3/4” HT approximately.

657-134 1118-790-9930Anti Vibration Damping Anti Vibration Damping For chain saw models: 028 and 038. Size: Steel plate: 1-11/16” Long X 1-3/16” Wide, with (2) 3/16” holes

657-136 1121-790-99061121-790-9909

Anti Vibration Damping For chain saw models: 024, 026, 028 and 038.Size: 15/16” OD (steel washer end) X 1-5/16” OD (rubber end) with a taper to 11/16” ID in rubber end. Overall height: 1-1/16”

657-135 1121-790-99111121-790-9912

Anti Vibration Damping Anti Vibration Damping for chain sawmodels: 024, 026, 038 & 088. Size: 1” OD (steel washer end) X 1-1/8” OD (rubber end) with a 3/8” ID in rubber end. Overall height: 1-1/16”

657-009 1111-790-9905

Anti Vibration Damping For chain saw models: 015AV, 051, 076 and TS510. Use on front handle, upper damper. Size: 1-1/4” OD with a 5/16” ID hole in the steel end.

657-010 1111-790-9915Anti Vibration Damping For chain saw models: 015AV, 051, 076 and TS510. Use on front handle, lower damper. Size: 1-11/16” OD with 25/32” ID hole in the steel end.

657-140 1111-790-9900Anti Vibration Damping Fits chain saw models: 051, 076 and TS510. Use on back handle. Size: 1-3/8” OD with 5/16” ID hole in the steel end.

657-532 1120-790-9600

Anti Vibration Damping For chain saw models: 010, 011, 012 AV and 019T. (While Quantities Last)

16-44



C C

657-081 1123-791-2800Anti Vibration Damping For chain saw models: MS170, MS180, MS270 and MS280. Size: 22mm (top recessed) / 25mm (bottom) X 11mm ID (recessed at the top) X 30mm overall length

657-082 1123-790-9900Anti Vibration Damping For chain saw models: 021, 023, 025, MS210, MS230 and MS250. Size: 22mm (top) / 25mm (bottom) X 11mm ID X 30mm overall length

657-083 1123-791-2805Anti Vibration Damping For chain saw models: 021, 023, 025, 029, 039, MS210, MS230, MS250, MS290 and MS390. Size: 23mm OD X 8mm ID X 30mm overall length

657-144 1122-790-9905Anti Vibration Damping For chain saw models: 028, 044, 046, 064, 066,MS440, MS460, MS461,MS640, MS660 chainsaws.Size: 1.00” / 25mm Bottom ODX .866” / 22mm Top OD (steel washer end) with 6mm ID hole. Overall HT: 1.10” / 28mm. (Two images shown for reference)

657-087 1125-791-2805Anti Vibration Damping For chain saw models: 034, 036, MS340 and MS360Size: 1-1/4” OD X 1” HT.

657-084 1128-790-9900

Anti Vibration Damping Tank / Annular Bufferfor chain saw models:044, 046, MS440, and 460.(Two pictures shown for reference)

657-088 1122-790-9920Anti Vibration DampingFor chain saw models:066 and MS 660.Size: 1.70” L X 1-180” W X 1.03” HT.

657-085 4224-790-9900Anti Vibration Damping Annular buffer forConcrete / Cut offCut quik saw model: TS700.(Two images shown for reference)

657-145 4205-790-9301 Anti Vibration Damping For concrete saw / cutquik saw models:TS510 and TS760.Size: 1.18” OD X 1.18” HT.

657-146 4205-790-9300Anti Vibration Damping For for concrete saw / cutquik saw models:TS410, TS420, TS480i, TS500i, TS510,TS700, TS760 and TS800.Size: 30mm OD X 15mm HT.

657-086 4221-792-9300Anti Vibration Damping Rubber buffer forConcrete /Cut offCut quik saw models:TS460, TS700 & TS800.

Size: 1-5/8” Long X 1-3/16” Wide X 5/8” Overall HT.(Two images shown for reference)

670-350 9022-341-10209022-371-1020

ScrewSpline screw with Hex head for Stihl handheld applications. Size: M5 X 20mm.

670-101 9220-260-1100Bar Nut Fits chain saw models: 010, 015, 020, 028 (old),031, 032, 041, 042, 045, 056 etc.Size: 8mm X 1.25 thread. For 13mm T-wrench

670-114 0000-955-0801Bar Nuts Bar nuts for Chain Saw models:021, 023, 025, 026, 028 series,038 Super series, 044, 064 etc. Size: 8mm X 1.25 thread

653-122 Bar Plate Set For chain saw model:08S (newer style)

653-113 1111-664-10001111-664-1005

Bar Plate Set For chain saw models: 050, 051 and 075.

670-201 0000-953-6605Bar studFits chain saw models: 024, 026, 028,034, 036, 038, 042, 044, 046, 048, 064, 066,MS 240, MS 260, MS 340, MS 341, MS 360, MS 361,MS 380, MS 440, MS 460, MS 640, MS 650, and MS 660.Size: 8mm with a 12mm wide collar X 42mm overall length.(Uses our 670-114 bar nuts)

875-272 9490-000-78409490-000-7850

Drive belt (cogged)For Cut Quik models: TS350, TS360 and TS460. Size: 3/8” W X 33-3/4” L

(Priced and Sold Individually)



16-45



C C

875-273 9490-000-7851Drive belt (cogged)For concrete / cut off saw model:TS400. Size: 3/8” W X 34-7/16” L

875-3820 9490-000-7901Drive belt (Type 6) MULTI RIBBEDFor concrete / cut off saw models: TS410 and TS480i. Size: 1/2” W X 29-1/2” L.

875-3821 9490-000-7900Drive belt (Type 6) MULTI RIBBEDFor concrete / cut off saw models: TS420 and TS500i. Size: 7/16” W X 32” L.

875-3822 9490-000-78919490-000-7892

Drive belt (cogged)For concrete / cut off saw models: TS510 and TS760 with 14” blade Size: 3/8” W X 36.3” L.

623-279 1110-129-1200Intake GasketFor chain saw model: 041.

618-006 HS320 / HS320A

Original Tillotson carburetor HS-320 / HS-320A.Found on Stihl chain saw models: 066 and MS660.Will replaces Zama C3A-S31 and Walbro WJ-67. Two images shown for reference.

FOR OTHER CARBURETOR PARTSSEE SECTIONS 10 and 11

606-776 9771-021-2580Clamping Collar Fits many Rubber Intake Elbowsfound on Stihl chain saws.

606-408 1123-141-2200

Carburetor Rubber Elbow Intake Manifold - Rubber. Fit Stihl chain saw models: 021, 023, 025, MS210 and MS250.

606-410 1121-141-2200Carburetor Rubber ElbowIntake Manifold - Rubber.Fit chain saw models: 024, 024AV,024 Woodboss, MS240, 026, 026AV, 026 PRO, MS260 / C.

606-415 1127-141-2200Carburetor Rubber ElbowIntake Manifold - Rubber.Fits chain saw models:029, 039, MS 290, MS 310 and MS 390.

606-412 1125-141-2200

Carburetor Rubber ElbowIntake Manifold - Rubber. Fits chain saw models: 034, 036 and MS360.

606-416 1128-141-22001128-141-22021128-141-2203

Carburetor Rubber ElbowIntake Manifold - Rubber Fits Stihl chain saw models:044, 046, MS 440, MS 460 and MS 461.

606-418 1122-141-2201Carburetor Rubber ElbowIntake Manifold - Rubber. Fits chain saw models: 066 and MS660.

606-400 4223-141-2200

Carburetor Rubber ElbowIntake Manifold - Rubber Fits Concrete / Cutquik sawmodel: TS400, TS700 and TS800.

606-402 4224-141-2202Carburetor Rubber ElbowIntake Manifold - Rubber.Fit Concrete / Cutquik sawmodels: TS700 and TS800.

606-775 1118-182-0900Control ShaftFits chainsaw model: 028 series.

606-770 1127-182-0900

Control ShaftFits Stihl chainsaw models:029, 039, MS290, MS310, MS390.

651-152 1118-664-16001120-664-1500

Chain AdjusterFor chain saw models:009, 028 and 038 series (old style)

651-155 1110-664-15001110-664-1600

Chain AdjusterFor chain saw models: 030, 031,032, 041, 042, 045, 048 and 056 series.

16-46



C C

651-157 0000-951-2911 1106-644-15001106-644-15011106-664-1501

Chain AdjusterFor chain saw models: 08S, 08 Super, 050, 051, 070, 075 & 090.

651-159 1123-640-19001123-664-1400

Chain Adjuster For chain saw models: MS210, MS230 and MS250.

651-158 1122-664-22001122-664-45001125-007-10211125-640-19009646-945-0490

Chain Adjuster KitFor chain saw models: 024, 026, 034, 035, 044, 046, 220, MS240, MS260, MS270, MS340, MS341, MS360, MS362, MS440, MS441, MS460, MS640, MS660. Includes: Tension Slide (1125-640-1900), Spur Gear, Adjusting Screw, Rubber O-ring 7X1.5 NOT shown in picture (9646-945-0490), Cover plate (1122-664-2200, Support (1122-664-4500).

652-200 1123-648-6600 Bumper StripsFits MOST Stihl chain sawmodels: 025 and smaller.(Priced and Sold in Pack of 4 Pieces)

652-202 1121-648-66051121-648-6610

Bumper StripsFits MOST Stihl chain sawmodels: 026 and larger.(Priced and Sold in Pack of 4 Pieces)

646-118 1113-160-2010

Clutch AssemblyFor chain saw models: 031, 032 and 041. Measures: 2-21/32” OD.

646-111 1123-160-20011123-160-2050

Clutch AssemblyFor chain saw models: 017, 018, 021, 023, 025, MS170,MS180, MS210, MS230 and MS250.Measures: 2-1/2” OD.

646-112 1121-160-2051

Clutch Assembly For chain saw models: 026 and MS260. (Washer plate includedas shown in picture).Measures: 2.675” OD X 0.403” Thick. 19mm nut attached to this clutch for removal.

646-114 1127-160-2051

Clutch Assembly For chain saw models: 029 and 039. (Washer plate includedas shown in picture). Measures: 2.928” OD X 0.403” Thick. 19mm nut attached to this clutch for removal.

646-116 1108-160-2002Clutch AssemblyFor chain saw model: 08S and Cut Quik models: TS350 and TS360.

Measures: 2-19/32” OD X 1/2” ID X 3/16” keyway

646-120 1119-160-2000Clutch Assembly For chain sawmodel: 038 series. Measures: 2-3/4” OD X 9/16” IDX 5/8” Overall Height.

646-117 1125-165-2052

Clutch Assembly For chain saw models: 036 / MS360.

Measures: 2.894” OD X 0.390” Thick. 19mm nut attached to this clutch for removal.

646-123 1125-160-20051125-160-2006

Clutch Assembly For concrete / cut quik saw model: TS400.

Measures: 2.885” OD

646-119 1122-160-20021122-160-2005

Clutch AssemblyFor chain saw models: 064, 066, MS640 and MS660.(Washer plate includedas shown in picture).

Measures: 3.140” OD X 0.460” Thick. 19mm nut attached to this clutch for removal.

646-124 1128-160-20001128-160-20041128-160-2001

Clutch AssemblyFor chain saw models: 044, 046, MS440, MS460, also fits MS341 & MS361. (Washer plate included as shown in picture). Measures: 2.916” OD X 0.392” Thick. 19mm nut attached to this clutch for removal.

16-47



C C

570-187 1130-020-12051130-020-12081130-020-12091130-020-1210

Cylinder Assy (38mm)Fits chain saw models:018 and MS180.Bore: 37 mm, Stroke: 28 mm, Displacement: 31.8 cc, Rings: 38 mm X 1.2 mm.

Important Note: Older 018 chainsaws made before serialnumber 2 44 534 710 have an 8mm wrist pin. This assembly will not fit.

570-188 1129-020-12021129-020-1206

Cylinder Assy (40mm)Fits chain saw models:020 T, MS 200 and MS200T.Bore: 40 mm, Stroke: 28 mm, Displacement: 35.2 cc, Rings: 40 mm X 1.5 mm.

570-189 1123-020-12091123-020-12231125-020-1224

Cylinder Assy (42.5mm)Fits chain saw models:0025 and MS250.Bore: 42.5 mm, Stroke: 32 mm, Displacement: 45 cc, Rings: 42.5 mm X 1.2 mm.NOTE: Will also fit on the smaller cousin model: 023 and MS230.

570-281 1121-020-12031121-020-1209

Cylinder Assy (44mm)Fits chain saw models: 026, MS260;NOTE: Will also fit024AV and 024 Super(Stihl# 1121-020-1200).

570-205 1121-020-1215 1121-020-1217

Cylinder Assy (44.7 mm) Fits chain saw model: MS260.

Note: Fits MS260WITH SERIAL NUMBERSAFTER 2 62 187 362.

018 & MS180

020 T & MS200and MS200 T

025 & MS250

026 / MS260

MS260

621-135 0000-997-5625Clutch SpringFor chain saw models:015 & 024 (old style). Measures: 5-3/4” overall length.

621-138 0000-997-5425Clutch Spring For chain saw model: 028 (old).Measures: 5-7/8” overall length.

621-137 0000-997-5811

Clutch Spring Fits chain saw models: 028 (new), 031, 041, 08 and 08S. Size: 15/16” overall length.

621-141 0000-997-6002Clutch SpringFor chain saw models: 051 and 075. Size: 1-1/4” length.

621-159 0000-997-09090000-997-5815

Clutch Spring Fits chain saw models: 029, 034, 036,MS 290, MS 340, MS 341, MS 360, MS 361 and MS 390. Size: 7/8” overall length

621-152 000-997-0907Clutch SpringFits chain saw models: 038, MS380. Size: 13/16” overall length

621-160 0000-997-0911

Clutch Spring Fits chain saw models:064, 066, MS640 and MS660. Size: 7/8” overall length

570-186 1130-020-1207Cylinder Assy (37mm)Fits chain saw models: 017 (NOTE)and MS170NOTE: This cylinder assembly fits model017’s after the sn 2 44 076 105 whichhave the later style ignition coil. If you havethe earlier style ignition coil, you will have tochange your coil and your flywheel.Bore: 37 mm, Stroke: 28 mm, Displacement: 30.1 cc, Rings: 37 mm X 1.2 mm.

570-183 1137-020-12011137-020-1204

Cylinder Assy (37mm)Fits chain saw models:MS192T.Bore: 37 mm,






017 & MS170

MS192T

16-48



C C

570-192 1140-020-12001140-020-1205

Cylinder Assy (47mm)Fits chain saw models:MS362.

570-251 1125-020-12061125-020-12091125-020-12131125-020-1215

Cylinder Assy (48mm) Fits chain saw models: 034 Super, 036 & MS360.

NOTE 1: This cylinderassembly has a holefor a decompression valve.NOTE 2: On older 034 saw (46mm) slight modification is required. Instructions are enclosed.This upgrade will increase your older 034 from 56.5cc to 61.5cc.

570-278 4221-020-1201

Cylinder Assy (48mm) Fits Cut Quik Sawmodel: TS460. Note: This cylinder assemblyhas the threaded hole beside the spark plug for a decompressor. Note: Decompression valve NOT included.

570-196 1127-020-12131127-020-1216

Cylinder Assy (49mm)Fits Stihl chain saw models: 039 and MS390;

NOTE: Will also work onsmaller cousin MS310.

570-227 4201-020-1200

Cylinder Assy (49mm) Fits Cut Quik Saw model: TS-360Replace your TS-350 with this C & P for extra power.

MS362

034 Super036 & MS360

TS460

039 & MS390

TS-360

570-191 1141-020-1200

Cylinder Assy (44.7mm)Fits chain saw models:MS261.

Uses our 570-004 decompression valve & 640-283 gasket set).

570-216 1118-020-12021118-020-1203

Cylinder Assy (46mm) Fits chain sawmodels: 028, 028 Super.

570-310 1127-020-12101127-020-12141127-020-12151127-020-12171127-020-1218

Cylinder Assy (46mm)Fits Stihl chain saw models:029 and MS290.

Bore: 46 mm, Stroke: 34 mm, Displacement: 56.5 cc, Rings: 46 mm X 1.5 mm.

NOTE: Will also fit on the larger cousin model: MS310.This cylinder will also replace the older 029 (45mm bore), beforeSerial Number X 39 305 257) as well.

570-155 1108-020-1220

Cylinder Assy (47mm)Fits Cut Quik Saw model: TS-350. (Also fits 08 & 08S Chain Saws)

570-194 1135-020-1202

Cylinder Assy (47mm)Fits chain saw model: MS361. Bore: 47 mm, Stroke: 34 mm, Displacement: 59 cc, Rings: 47 mm X 1.2 mm.

MS261

028, 028 Super

029 & MS290

TS-350 Cut Quik

MS361

16-49



C C

570-161 1128-020-1250

Cylinder Assy (52mm)Fits Stihl Cut Quik / Concrete Saw model: GS 461 ROCK BOSS also used on Stihl chainsaw model: MS461. Includes: cylinder, piston and rings, piston pin & clips.

570-272 1119-020-12021119-020-1215

Cylinder Assy (52mm) Fits chain saw model: 038 Magnum.

NOTE: This cylinder is NOT equipped with a De-compression valve hole. For a cylinder with a Decompression valve hole see our 570-206. (Also see our 623-672, 640-238 or 640-272).

570-206 1119-020-1204

Cylinder Assy (52mm)Fits chain saw model: MS381.

Note: Decompression valveNOT included, use our 570-004 Decompression valve.Bore: 52 mm, Stroke: 36 mm,Displacement: 76.5 cc, Rings: 52 mm X 1.5 mm.

570-211 1128-020-12211128-020-1217

Cylinder Assy (52mm)Fits chain saw models: 046 & MS460.

570-162 1111-020-1200

Cylinder Assy (52mm)Fits chain saw models: 051 and Cut Quik model TS-510.

GS 461 R.B.MS461

038 Magnum

MS381

046 & MS460

051 / TS-510

570-275 4250-020-1200

Cylinder Assembly (48mm)Fits Stihl Cut Quik models:TS480i and TS500i.

570-277 4223-020-1200

Cylinder Assembly (49mm)Fits Cut Quik Saw model: TS400. Decompression valve NOTincluded, uses our 570-002.

570-210 1128-020-12131128-020-1226 1128-020-1227

Cylinder Assy (50mm) Fits chain saw models: MS440 andnewer style 044 afterSerial No. 29583701.

NOTE: If your saw is equippedwith a 10mm PISTON PIN you willneed to order our 590-152Crankshaft Assembly separately,which will accept the newer 12mm piston pin.

570-209 1138-020-1201

Cylinder Assy (50mm) Fits chain saw model: MS441 and MS441C.

570-276 4238-020-1202

Cylinder Assy (50mm)Fits Cut Quik Saw models: TS410 and TS420.

Decompression valve NOT included. Comes with threaded plug only.Also see our 640-285 Gasket Set.

TS480i, TS500i

TS400

044 / MS440

MS441 / MS441C

TS410 & TS420

16-50



C C

572-590 4119-030-2003

Piston Assembly (38mm)Fits Trimmer models: FS220 and FS220R.

572-601 1123-030-2019

Piston Assembly (40mm)Fits chain saw models: 023 / MS230 (40mm).

Note: Fits older 021 chainsaws (Before S/N X 34 944 403).Piston Pin 10mm x 6.5mm x 28mm, Circlips 10mm.(Rings 40mm x 1.2mm)

572-604 1121-030-2005

Piston Assembly (42mm)Fits chain sawmodels: 024 / MS240. (Rings 42 X 1.5mm)

572-607 1123-030-2003

Piston Assembly (42mm)Fits Stihl chain saw models: MS250. Note: For 025 model with larger 42.5mm bore see our 572-603 piston assembly.(Rings 42 X 1.5mm)

572-603 1123-030-2011

Piston Assembly (42.5mm) Fits chain saw models: 025.

Note: For MS250 model with smaller 42mm bore see our 572-607 piston assembly.(Rings 42.5 X 1.2mm)

572-525 1121-030-2001

Piston Assembly (44mm) Fits chain saw models: 026 and MS260.

NOTE: This piston assembly fits the older 026, MS260 Stihl models before serial# 2 62 187 362. This WILL NOT fit the newer MS260models with the larger 44.67mm bore.

572-599 1121-030-2003

Piston Assembly (44.7mm) Fits Stihl chain saw models: 026 and MS260.

NOTE: This piston assembly fits the newer 026, MS260 Stihl models after serial# 2 62 187 362. NOTE: For the older 44mm piston assembly see our 572-525.

570-212 1122-020-1209 1122-020-1211

Cylinder Assy (54mm) Fits chain saw models: 066 & MS660.

570-200 1128-020-11211128-020-1217

Cylinder Assy (54mm)Fits Stihl chain saw models: 046 / MS460 (BIG BORE). Includes: cylinder, piston and rings, piston pin & clips. Bore: 54 mm, Stroke: 36 mm, Displacement: 82.5 cc, Rings: 54 mm X 1.2 mm.Note: Decompression valve NOT included.

570-204 4224-020-1202

Cylinder Assy (56mm)Fits Stihl concrete / cut off saw model: TS700 and TS800.

570-214 4205-020-1200

Cylinder Assy (58mm)Fits Stihl concrete / cut off saw model: TS760.

705-900 Universal

Piston Ring Assembly Tool Kit / Piston Ring Clamp Set.

Useful for assembling pistons and cylinders on chainsaws, trimmer etc. 4 sizes of clamps. Give yourself a third hand with this kit. This kit will compress piston rings ranging from 30mm to 60mm in diameter.

066 & MS660

046 / MS460

TS700 & TS800

TS760

16-51



C C

572-384 1118-030-2001

Piston Assembly (44mm)Fits Chain Saw models: 028 and 028 Wood Boss

“older style”.

572-255 1110-030-20021110-030-2000

Piston Assembly (44mm)Fits Stihl chain saw model: 041 old style.

572-699 1113-030-2001

Piston Assembly (44mm)Fits Chain Saw model: 031.

572-388 1113-030-2003


572-449 1118-030-2003

Piston Assembly (46mm)Fits chain saw model: 028 Super. Replacement piston assembly for our 570-216.

572-600 1127-030-20001127-030-2003

Piston Assembly (46mm)Fits Stihl chain saw models:029 and MS290

NOTE: For 1mm larger OD piston assembly see our 572-608.

572-602 1135-030-2000

Piston Assembly (47mm)Fits chain saw model: MS361. (ring thickness 1.2)

572-247 1108-030-2020

Piston Assembly (47mm)Fits chain saw models: 08, 08S, and Cut Quik model TS-350. (Replacement piston assembly for our 570-155.)

572-608 1113-030-2001

Piston Assembly (47mm)Fits Stihl chain saw models: MS310.

572-497 1125-030-2001

Piston Assembly (48mm)Fits chain saw models: 034 Super and 036.

572-614 4221-020-1201

Piston Assembly (48mm) Fits Cut Quik Saw model: TS460.

Replacement piston assembly for our 570-278.

572-606 1127-030-2005

Piston Assembly (49mm)Fits chain saw models: 039 / MS390.

572-460 4201-030-2000

Piston Assembly (49mm) Fits Cut Quik model: TS-360.

Replacement piston assembly for our 570-227

572-521 4223-030-2000

Piston Assembly (49mm) Fits Cut Quik Saw model: TS400.

Replacement piston assemblyfor our 570-277

572-441 1119-030-2001Piston Assembly (50mm) Fits chain saw model: 038 Super.

Replacement piston assemblyfor our 570-208.

572-610 1128-030-2015

Piston Assembly (50mm)Fits chain saw models: 044 / MS440. NOTE: 12mm piston pin.

NOTE: This piston WILL NOT fit theolder 044 models that had a 10mm piston pin.

16-52



C C

572-617 4238-030-2003

Piston Assembly (50mm) Fits Cut Quik Saw models:TS410 and TS420.

(Replacement piston assemblyfor our 570-276)

572-611 1115-030-2000


572-515 1119-030-20021119-030-2003

Piston Assembly (52mm) Fits chain saw model: 038 Magnum, MS380, MS381.

(Replacement piston assembly for our 570-272.)

572-261 1111-030-2000

Piston Assembly (52mm)Fits chain saw model: 051 and Cut Quik Saw model TS-510.

(Replacement piston assemblyfor our 570-162.)

572-612 1128-030-2009

Piston Assembly (52mm)Fits chain saw models: 044 Big Bore, 046 and MS460.

572-615 1122-030-2001


572-613 1115-030-2001

Piston Assembly (52mm)Fits chain saw models: 045 and 056AV - older version.

572-390 1115-030-2002

Piston Assembly (54mm) Fits chain saw model: 056.

572-616 1122-030-2005


572-620 1111-030-2002

Piston Assembly (58mm)Fits chain saw models: 075, 076 and TS760.

572-619 1106-030-20001106-030-2003


574-167 1123-034-3005

Piston Ring Set (40mm X 1.2mm).Fits chain saw model: 023, MS210 (older) and MS230. NOTE: Fits older 021 models (Before S/N X 34 944 403).Note: Some chain saw applications use one only piston ring.

NOTE: YOU WILL NEED TO CONFIRMTHE PISTON RING THICKNESS PRIOR TO ORDERING.

574-212 1121-034-3005Piston Ring Set (42mm X 1.5mm) Fits chain saw models: 024 / MS240. (Priced and sold in sets)

574-214 1110-034-30001121-034-3010

Piston Ring Set (44mm X 1.2mm)Fits chain saw models: 026 and MS260.Fits Stihl trimmer models: FS 480 and FR 480.(Priced and Sold in sets)

574-170 1110-034-30001121-034-3010

Piston Ring - Chrome (44mm X 1.2mm)Fits chain saw models: 026 and MS260. NOTE: YOU WILL NEED TO CONFIRMTHE PISTON RING THICKNESS PRIOR TO ORDERING.(Priced Individually - 2 Required)

574-216 1110-034-3000Piston Ring Set (44mm X 1.5mm) Fits chain saw models:028, 030, 031 and 041.Replacement ring for our 572-525 piston assembly.(Priced and sold in sets)

574-221 1118-034-3001

Piston Ring Set (46mm X 1.5mm)Fits chain saw models: 028 Super, 029,MS290 and 034 (with smaller 46 mm bore).(Replacement rings for our 572-449 piston assembly)

16-53



C C

574-144 1118-034-3001Piston Ring - Chrome (46mm X 1.5mm)Fits chain saw models: 028 Super, 029,MS290 and 034 (with smaller 46mm bore). Replacement ring for our 572-449 piston assembly.(Priced Individually - 2 Required)

574-258 1125-034-3001Piston Ring Set (48mm X 1.2mm)Fits chain saw models:034, 036 and MS360.(Priced and Sold in sets)

574-232 1110-034-3003

Piston Ring Set (48mm X 1.5mm).Fits chain saw model: 041 and will fit many036 and MS360 models using the thicker 1.5mm ring.NOTE: This ring set fits our 572-497 Piston assembly.

Note: Some chain saw applications use one only piston ring.

NOTE: YOU WILL NEED TO CONFIRMTHE PISTON RING THICKNESS PRIOR TO ORDERING.(For thinner 1.2mm piston ring set see our 574-258).

574-234 1127-034-30064201-034-3000

Piston Ring Set (49mm X 1.5mm).Fits chain saw model: 039, MS390Fits Cut Quik models: TS360 and TS400.

For Chrome piston ring see our 574-143.Note: Some chain saw applications use one only piston ring.

NOTE: YOU WILL NEED TO CONFIRMTHE PISTON RING THICKNESS PRIOR TO ORDERING.

574-143 1127-034-3006 4201-034-3000

Piston Ring - Chrome (49mm X 1.5mm)Fits Cut Quik Saw model: TS-360 and TS400.(Priced Individually - 2 Required)

574-264 1128-034-3000

Piston Ring Set (50mm X 1.2mm)Fits chain saw models:044, MS440 and MS441.(Priced and Sold in sets)

574-137 1119-034-3000

Piston Ring - Chrome (50mm X 1.5mm)For chain saw model: 038 Super. (Priced Individually - 2 Required)

574-265 1122-034-3000

Piston Ring Set (52mm X 1.2mm)Fits chain saw models:044 BIG BORE, 046, MS460,064, MS640, MS650 and some 051, TS510 models..(Priced and Sold in sets)

574-248 1115-034-3010

Piston Ring Set (52mm X 1.5mm) Fits chain saw models:038 Magnum, MS380, MS381,045, 048, 050, 051 and 056. (Priced and sold in sets)

574-106 1115-034-30011115-034-3010

Piston Ring - Chrome (52mm X 1.5mm) Fits chain saw model: 038 Magnum,051 and TS510 cut quik saws.(Priced Individually - 2 Required)

574-266 1122-034-3001

Piston Ring Set (54mm X 1.2mm)Fits chain saw models:046 BIG BORE, 066 and MS660.(Priced and Sold in sets)

574-254 1115-034-3012

Piston Ring Set (54mm X 1.5mm) Fits chain saw models: 045 and 056. (Priced and sold in sets)

Note: “Piston Rings” are priced and sold individually. “Piston Ring Sets”

are priced and sold as a set of 2

591-102 9512-003-2250Bearing - Piston Fits chain saw models: 023, 024,025, 026, MS230, MS240, MS250,MS260 and others.(Size: 10mm X 13mm X 12.5mm).

591-109 9512-003-2340Bearing - PistonFits chain saw models: 028, 029, 030, 031, 032,034, 036, 039, 041, 044 (with 10mm OD piston wrist pin), BR106, BT106, FR106, FR108, FR135, FR145, FR220, FS106, FS108, FS160, FS180, FS20, FS220, FS280, FS290, FS360, FS410, FS420, FS500, FS550, FS90, FS96, MS290, MS310, MS340, MS360, MS390 and TS400 Cutquik saw.(Size: 10mm X 14mm X 13mm).

591-101 9512-003-3140Bearing - PistonWrist pin bearing for chain saw models:08S & 038, 038 Super / Magnum and Concrete Saw models TS350 & TS360.(Size: 12mm X 16mm X 13mm)

591-104 9512-003-3061Bearing - Piston Wrist pin bearing for Chain Saw models:044, 046, MS440 and MS460.(Size: 12mm X 15mm X 15mm).

16-54



C C

591-106 9512-003-3281Bearing - Piston Wrist pin bearing for Chain Saw models:066 and MS660. (Size: 12mm X 17mm X 13mm).

591-110 9512-003-3440Bearing - Piston Wrist pin bearing for Chain Saw models:050, 051, 075, 076, 084, 088, MS780,MS880, TS50, TS510 and Cut Quik saw model: TS760.(Size: 13mm X 17mm X 17.5mm)

590-151 1125-030-0407 Crankshaft AssemblyFits chain saw models:036 and MS360.(Uses our 646-117 clutch assembly).

590-150 1119-030-0400

Crankshaft AssemblyFor chain saw models: 038, 038 Super and 038 Magnum.

590-117 1110-030-0401

Crankshaft Assembly. For chain saw model: 041.(While Quantities Last)

590-152 1128-030-0406 Crankshaft AssemblyFits chain saw models:044 and MS440.

(Uses our 646-124 clutch assembly).

590-153 1128-030-0402 Crankshaft AssemblyFits chain saw models:046 and MS460.(Uses our 646-124 clutch assembly).

590-154 1122-030-0407

Crankshaft AssemblyFits chain saw models:064 and 066 (old style).Fits older 064 and 066 models > before serial numberX 33 917 066, MS 640. For newer 066 chainsaws models (approximately 1996 on) that have a larger diameter crankshaft. See part# 590-155.(Uses our 646-119 clutch assembly).

590-155 1122-030-0408

Crankshaft AssemblyFits chain saw model: 064.Fits newer 066 models > before serial numberX 33 917 065, MS 650 and MS660. For older 066 chainsaws models (prior to 1996 approx) that have a smaller diameter crankshaft. See part# 590-154.(Uses our 646-119 clutch assembly).

590-119 1111-030-0402

Crankshaft Assembly For chain saw models: 051, 075and Cut Quik Saw model TS-510.

590-116 1108-030-0402

Crankshaft Assembly For Cut Quik Saw models: TS-350 and TS-360, also fits Chain Saw models: 08 and 08S.

590-156 4223-030-0400

Crankshaft Assembly For Cut Quik Saw model: TS400.

590-157 4238-030-0400Crankshaft AssemblyFits Cut Quik / Concrete sawmodels:TS410 and TS420.

592-109 9503-003-0540Bearing - Crankshaft Fits chain saw models: 051 and 075 - (clutch side)Size: 20mm ID X 47mm OD X 14mm HT. (Bearing# 6204/C3) Open both sides

593-102 9503-003-0310Bearing - CrankshaftFits chain saw model: 041 - (flywheel side)Size: 15mm ID X 32mm OD X 9mm HT.(Bearing# 6002/C3) Open both sides

592-107 9503-003-03519503-003-03589503-003-0360

Bearing - CrankshaftFits Concrete saw / Cutquik saw models:TS410 and TS420. Grooved Ball Bearing.Size: 15mm (.587”) ID X 36.3mm (1.428”) OD X 11mm (.428”) HT. Open both sides. NOTE: These bearing will NOT fit on the “Z” TS410 & TS420 models.(Use with our 590-157 crankshaft assembly).

593-103 9503-003-04409503-003-0450

Bearing - CrankshaftFits Stihl chain saw models: (flywheel side) 038, 038 Super, 038 Magnum, 051, 075 and TS-510 and TS-400 (recoil side) cut quik saws. Also Stihl TS480i, TS500i, TS700 and TS800 Cutquik saws.Size: 17mm ID X 40mm OD X 12mm HT.(Bearing# 6203/C3) Open both sides

16-55



C C

640-234Gasket SetFits chain saw models: 034, 034 Super, 036 (No oil seals included)(While Quantities Last)

640-268 1125-007-1050

Gasket SetFits chain saw models:034, 036, MS340 and MS360.(Oil seals included (1) 622-241 (15mm ID X 29.6mm OD X 4mm) + (1) 622-226 (12mm ID X 20mm OD X 5mm).

640-272 1119-007-1050

Gasket Set Fits chain saw model: 038 series. (Includes oil seals)

640-238 1119-007-1050

Gasket SetFits chain saw models: 038 series,038 Super, 038 Magnum, MS380and MS381.

(Fits our 570-206, 570-208 and 570-272).

640-278 1110-007-1050

Gasket Set Fits chain saw model: 041 and 041 Farm Boss. (While Quantities Last)

640-136Gasket Set Fits chain saw models: 050 and 051. (No oil seals included)(While Quantities Last)

640-287Gasket Set Fits chain saw models: 08, 08S and Cut Quik models: TS-350 and TS-360. (Includes oil seals)

640-181 4223-007-1050

Gasket Set Fits Cut Quik model: TS400. (oil seals included)

592-106 9503-003-03409503-003-0341

Bearing - Crankshaft Fits models: 08S, 038,038 Super, 038 Magnum and 041 - (clutch side). Cut-Quik models: TS350 & TS360 - (clutch & flywheel side); also fits Cut-Quik model: TS400. Fits models 034, 036, 044, 046, MS360, MS440 and MS460 (flywheel side). Size: 15mm (37/64”) ID X 35mm (1-3/8”) OD X 11mm (7/16”) HT (Bearing# 6202 - open both sides)

570-002 4223-020-9400 / 4238-020-9400Wacker# 0104064

Decompression Valve For chain saw and Concretesaw cylinder assemblies. Fits models: TS400, TS700 and TS800

570-004 1128-020-9400Decompression ValveFor chain saw and Concrete saw cylinder assemblies. Fits models: 026, 036, 044, 046, 066, MS260, MS360, MS440, MS441, MS460, MS650, MS660.

570-006 1135-020-9400Decompression Valve(Black Knob).For chain saw models:MS311, MS361, MS362,MS391 and MS441.

640-288 1121-007-1050

Gasket SetFits Stihl chain saw models: 026 and MS 260. (Oil seals included).Fits our 570-205 Piston & Cylinder Assy.

640-180

Gasket Set Fits Stihl chain saw model: 026.(oil seals included).(Used with our 570-281 Cylinder Assy).

640-283 1141-007-1000

Gasket SetFits chain saw model:MS 261.(Oil seals included).Fits our 570-191 Piston & Cylinder Assy.

640-269Gasket Set Fits chain saw model: 028 Super. (No oil seals included)(While Quantities Last)

16-56



C C

640-285 4238-007-1003

Gasket Set Fits cut quik / concrete saw models: TS410 and TS420. (Includes oil seals)For use with our 570-276 Cylinder Assy.

640-275 1128-007-1050

Gasket Set Fits chain saw models: 044 and MS440. (Includes oil seals)

640-279 1128-007-1052

Gasket Set Fits chain saw models: 046 and MS460. (Includes oil seals)

640-280 1122-007-1053

Gasket SetFits chain saw models: 066 / MS660. (Includes oil seals)

640-281 4221-007-1050

Gasket SetFits Stihl concrete saw / cut quik saw model: TS460.

640-282 1111-007-1051

Gasket SetFits Stihl concrete saw / cut quik saw model: TS760. (Oil seals included)

623-617 1129-029-2303

Head / Base GasketFits chain saw models: MS200 / T .

623-618 1141-029-2302

Head / Base GasketFits chain saw model: MS 261 (Metal).

623-619 1135-029-2300

Head / Base GasketFits chain saw models: MS341, MS361 and MS361C (Metal).

623-620 1140-029-2300

Head / Base GasketFits chain saw models: MS362 / C (Metal).

623-611 1113-029-2300 / 1118-029-23001118-029-2305 / 1118-029-2306

Head / Base GasketFits chain saw models: 024, 026,028, 031, 032, MS240 and MS260.

623-672 1119-029-23001119-029-2301

Head / Base Gasket Fits chain saw models: 034, 036,038 series, MS 340 and MS 360.

623-678 1110-029-2300Head / Base Gasket Fits chain saw model: 041.

623-687 1108-029-2300Head / Base Gasket Fits chain saw models: 08, 08S & Cut Quik models: TS-350 and TS-360.

623-616 4238-029-2300Head / Base GasketFits concrete / cut quik saw models:TS410 and TS420. (Metal).

623-431 1111-029-2300Head / Base Gasket Fits chain saw models: 051 and Concrete saw model: TS510.

623-612 1128-029-23001128-029-2301

Head / Base Gasket onlyFits chain saw models:044 and MS440. (Metal).

623-448 1138-029-2300Head / Base GasketFits chain saw models: MS 441.

623-613 1128-029-2304Head / Base Gasket onlyFits chain saw models: 046 / MS460. (Metal).

623-614 1122-029-2301Head / Base Gasket onlyFits Stihl chain saw models: 066, MS650 & MS660. (Metal).

623-615 4223-029-2301Head / Base Gasket onlyFits concrete saw model: TS400. (Metal).

640-022Gasket Set - Upper.Fits chain saw models:034, 034 Super and MS360 etc.

16-57



C C

610-055 1110-358-1800

Replacement Fuel Filter Element For our 610-170. Will replaces the original Stihl element. Measures: 1” L X 3/4” OD (Made of foam material).

610-170 0000-350-3500 1115-350-35031120-350-3500

Fuel Filter (Orange Colour)For chainsaw models using 1/4” molded fuel lines.Models: 030, 031, 032, 038, 041, 042, 044, 044, 045, 046, MS460, 048, 064, 066, 075, etc. Stihl CutQuik Saw models: TS08, TS50, TS350, TS350 AVE, TS360, TS400, TS460, TS510, TS760.

613-605 0000-350-3502 / 0000-350-35030000-350-35061115-350-3503

Fuel Filter - In Tank Use with molded fuel lines. Fits chainsaw models: 034, 036, 038; Stihl Cut Quik / Concrete saw models: TS410 and TS420 Cutquik. Measures: 11/16” OD X 1-5/8” overall length.

613-607 0000-350-3504 / 0000-350-35151115-350-3503

Fuel Filter - In TankFor use with molded fuel lines.Fits chain saw models: 034, 036, 038,044, MS440, 046, MS460, 064, MS640, 066, MS660 etc. NOTE: Similar to our our 613-605 but larger diameter. Recommended for larger cc Stihl chain saws. etc. Measures: 1-3/4” overall length X 23mm diameter.

610-125 1123-358-77011123-358-7702

Molded Fuel Line Fits chain saw models: 021, 023, 025, MS210, MS230, MS250.Note: Designed to be used with engines manufactured before January 2012; Not to be used with engines manufactured after January 2012.

610-123 1121-358-7700

Molded Fuel LineFits chain saw models:024, 026, MS 240 and MS 260.

610-120 1133-647-9400

Molded Hose / Molded Fuel LineFits chain saw models: MS270 and MS280.

610-122 1127-358-7702Molded Fuel LineFits chain saw models: 029, 034, 036, 039, MS290, MS360, MS390.

610-121 1119-358-7700 / 1118-358-7701

Molded Fuel Line For chain saw models:034, 034 Super and 036 (previous to serial number)X39108850; 038 series as well as model 064 (previous to serial number X19512349.) Measures: 4-3/4” Long

610-128 1119-358-7702

Molded Fuel LineFits chain saw models: MS381

610-129 1128-358-7701

Molded Fuel Line Fits chain saw models: MS341, MS361, 044, 046, MS440 & MS460.

610-130 1124-358-7700

Molded Fuel Line Fits chain saw models: 066, MS640,MS650, MS660, MS780, 084, 088, MS780 and TS800.

610-136 1115-141-8600Molded Impulse HoseFits chain saw models:028, 042, 045 and 056.

610-132 1106-647-9404Molded Oiler Hose / Oil TubeFits chain saw models:028, 030, 031, 032, 038, 070, 075,090, MS 380, MS 381. (This hose connects to the oil pump).

610-134 1122-647-9400Molded Oiler Hose / Oil Tube ONLY, Pick-up filter body not included. Oil pump pick-up hose only.Fits chain saw models: 024, 026,034, 034, 036, 036QS, 064, 066,MS240, MS260, MS260C, MS340, MS341,MS360, MS360C, MS361, MS361C, MS362,MS362C, MS441, MS441C, MS640, MS650 and MS660.

550-161 1130-350-0500Fuel Cap Fits Stihl chain saw models:017, 018, 019, MS170, MS180,MS190, MS190 T and MS191 T.

550-120 1110-350-0502Fuel Cap For chain saw models: 041, 051 and 075.

550-145 0000-350-05201117-350-0500

Fuel & Oil Cap (40mm) Gas Cap for chain saw models: 020, 021, 023, 024, 025, 026,028, 028 Super, 029, 034, 034 Super, 036, 038 series, 039, 044, 046, MS290, MS310 and MS390. Oil Cap for Stihl chain saw models: 044, 046, 050, 064, 084, MS640, MS650 and MS660.

550-158 0000-350-0531 / 1124-350-0500Fuel Cap For chain saw models: 064, 066, MS660 and 084. Thread OD: 1.54” or 39.06mm

16-58



C C

550-121 1107-350-0500Fuel Cap For chain saw models: 08, 070, 090 and Cut Quik models: TS-350 & TS-360.

551-149 0000-350-05101117-640-3600

Oil Cap and Fuel Cap (30mm) For chain saw models: 009, 010, 011, 012, 020, 021, 023, 024, 025,026, 028, 028 Super, 032, 034, 034 Super, 036, 038, 042 and 048. Fuel Cap for chain saw model: 048.

551-155 0000-350-0526Oil Cap For chain saw models: HT 100, HT 101, HT 130, HT 131, HT 250,HT 70, HT 73, HT 75, HTE 60, HT-KM.Gas CAP For the following models: 021, 023, 025, 026, 034, 036, 036QS, MC 200, MS 171, MS 181/C, MS 192/C/T, MS 200/T, MS 210/C, MS 211, MS 230/C, MS 240, MS 250/C, MS 260/C, MS 340, MS 360/C and MS 381.(Flip Top Style). Size: O-Ring Seal OD = 1.20”.

550-160 0000-350-0525Fuel CapFor chain saw models: 020, 021 023, 024, 025, 026, 029, 034, 036, 039, 044, 046, 088, BG45, BG46, BG55, MS171, MS181, MS192, MS200, MS210, MS211, MS230, MS240, MS250, MS260, MS270, MS290, MS310, MS340, MS341, MS360, MS361, MS362, MS380, MS381, MS440, MS441, MS460 and MS880. (Flip Top Style). Size: O-Ring Seal OD = 1.35”. Note: NOT compatible with > 10% ethanol fuel.

550-164 4223-350-0500

Fuel Cap / Gas Cap For Stihl concrete / cut quik saw model: TS400. Note: NOT compatible with > 10% ethanol fuel.

627-038 1119-640-71001119-642-1501

Oil Pump Spur Gear & Oiler Worm Gear Set for Stihl. Includes (1) oil pump spur gear (Replaces Stihl# 1119-642-1501). This nylon gear drives the oiler gear on saw & fits Stihl chainsaw models: 038, MS380 & MS381 ONLY. Also included is (1) oiler worm gear (Replaces Stihl# 1119-640-7100). This nylon sprocket comes complete with bushing attached. It drives the oiler and fits on Stihl chainsaw models: 038, MS380, MS381 as well as 028, 042 and 048 models.

627-380 1119-640-3200

Oiler / Oil Pump AssemblyFits chain saw models: 038, MS380, MS381, 042AV and 048.

627-326 1121-007-10431121-640-32031121-640-3205

Oiler / Oil Pump Assembly Fits chain saw models: 024, 026, MS240 and MS260.

627-336 1125-640-32011125-640-3206

Oiler / Oil Pump AssemblyFits chain saw models: 034, 036 and MS360.

627-346 1128-640-3206

Oiler / Oil Pump AssemblyFits chain saw models: 046, MS460, MS441 & MS441C.

627-660 1122-640-3205

Oiler / Oil Pump Assembly Fits chain saw models: 066 / MS660.

627-026 1121-640-7111Worm GearFits chain saw models: 026, MS260 and (Later Type) MS240 and MS261.

627-029 1125-640-71101125-647-2400

Worn Gear and Spring Fits chain saw models: 029, 034, 036, 039.

627-044 1128-640-71101128-640-7112

Worn Gear and Spring Fits chain saw models: MS341, MS361,MS362, 044, 046, MS440, MS441, MS460, MS461.

627-066 1122-640-71001122-640-7105

Worn Gear and Spring Fits chain saw models: 064, 066, MS650 and MS660.

600-169 0000-400-1302 / 0000-400-13061123-400-1301

Electronic Coil Fits chain saw models: 009, 010, 011, 012, 020, 020T, 021, 023, 025, MC 200, MS200, MS210, MS230 and MS250.

16-59



C C

600-402 1123-400-1301Electronic Coil Fits chain saw model: Most MS210 C-BE Z,MS230 C-BE Z and MS250 C-BE Z.(NOTE: Please verify the O.E.M. to enginemodel as part does not fit all applications!).

600-358 0000-400-1300

Electronic Ignition For chain saw models: 024, 026, 028, 028WB, 029, 034,034AV, 036, 038, 039, 044, 048, 064, MS240, MS260, MS290, MS310, MS340,MS360, MS380, MS381, MS390, MS440 and MS640; also Trimmer models: FS360 and FS420.

600-406 1122-400-1314

Electronic Ignition. Fits on Stihl chain saw models: 046, 066, MS460, MS650 and MS660

600-400 4223-400-1301 4223-400-1302 4223-400-1303

Ignition CoilFor concrete / cut quik saw.Fits model: TS400. Two bolt style (bolts not included). Coil comes complete with 13” of 5mm coil wire.

600-100Ignition Coil and Core For chain saw models: 08 and 08S. NOTE: Found on other equipment using theold 08 style power plant. ie: Stihl auger etc.

430-027 1100-430-02021110-430-02101121-430-0200

Stop Switch Kill Switch for chain saw models: 024, 026, 070 and Cut Quik Saw models 08S, TS-350 and TS-360. Measures: 3/4” X 1” X 1-1/2”

430-017 Universal Type

Toggle Kill Switch Kill switch found on many small older Chain Saw models with spade terminal wire end.

636-125 1125-140-0604

Muffler / Exhaust For chain saw models: 021, 023, 025,MS210,MS230 and MS250.

636-150 1121-140-0606

Muffler / Exhaust For chain saw models: 024, 026 and MS260.

636-152 1127-140-0605

Muffler / Exhaust For chain saw models: 029, 039, MS290, MS310 and MS390.

636-151 1125-140-06071125-140-06091125-140-6111

Muffler / Exhaust For chain saw models: 036, MS360and will fit some 034 Super models - see measurements. (You may need aspacer on some 034 models). Mountingbolt holes measure: 1.69” / (43mm) center to center / bolt holes measure: 7.3mm OD. Depth: 3” approximately.

636-297 1110-140-0613

Muffler / Exhaust For chain saw models: 040, 041 and 041G. (Uses our 623-157 exhaust gasket)

636-118 1111-140-0613

Muffler / Exhaust Muffler for chain saw models: 051 (old style)

636-138 1119-140-0604

Muffler For chain saw models:MS381.

(2) 6mm none-threaded mounting holes at bottom of muffler on 93mm centers. Front cover held on with two screws - see picture on-line. OVERALL HEIGHT OF FRONT COVER = 95mmapproximately.(Uses our 623-132 exhaust gasket).For older 038 series see our 636-139 muffler.

636-139 1119-007-1005 / 1119-007-10271119-140-0600

Muffler / Exhaust For chain saw models:038 and 038 Super.

(2) 6mm none-threaded mounting holes at bottom of muffler on 93mm centers. Front cover held on with one screw mounted in the center. OVERALL HEIGHT OF FRONT COVER = 90mmapproximately. (Uses our 623-132 exhaust gasket).

16-60

STIHL continuedSTIHL continued


C C

623-132 1117-149-0601 1115-149-0601

Chainsaw Exhaust Gasket For chain saw models: 038 series.

636-154 1128-140-06121128-140-0616

Muffler / Exhaust Dual port muffler for chain sawmodels: 044, 046, MS440 & MS460. This is an aftermarket muffler. The dual port design add power. Complete with front baffle and spark arrester screens.

636-156 1122-140-0614

Muffler / Exhaust Single Port mufflerfor chain saw models: 066, MS660 & MS650.

636-153 1122-140-06131122-140-0800

Muffler / ExhaustDual Port muffler for chain saw models: 066, MS660 and MS650. (Also see our 636-156)

636-117 1108-140-0600

Muffler / Exhaust For models:08 and 08S. Note: Front and back images shown for reference.

636-171 4201-140-06074201-149-0601

Muffler / Exhaust For Cut Quik Saw models: TS350 and older TS360. NOTE: photo shows front and back images.(While Quantities Last)

636-173 4223-140-0601

Muffler / Exhaust For Cut Quik / Concrete Sawmodel: TS400.

636-174 4238-140-0611

Muffler / Exhaust Fits Cut Quik / Concrete Sawmodels: TS410 and TS420.

623-135 1125-149-0601Chainsaw Exhaust Gasket For cut quik / concrete saw model: TS400 series. (Fits our 570-277).

622-226 9640-003-1190Oil seal For chain saw models: 020, 024,026, 034, 036, MS360, FS220, and 280. Size: 12mm X 20mm OD X 5mm.

622-233 9640-003-13409640-006-1314

Oil seal For chain saw models: 028, 030, 031, 032, 038, MS380, MS381 (Magneto side). Trimmer models: FS360, FS420, FS500 and FS550 and Blower models: BR 320, BR 340 L, BR 380, BR 400, BR420, BR420 C, SR 320, SR 400, SR 340 and SR 420.Size: 13mm X 22mm OD X 5mm

622-262 9640-003-1355Oil Seal Fits chain saw models: 046, MS460, 064, MS640.Size: 13.5mm X 20mm OD X 4mm. NOTE: You will need to confirm the measurements of your old seal to see if they match.

622-260 9642-003-1440 Oil Seal Fits chain saw models: 050, 051, 075 & 076and Cut Quik models: TS510 and TS760.Size: 14mm X 20mm OD X 3.5mm.

622-263 9640-003-1560 Oil Seal (Flywheel side) Fits chain saw models:039, 064, 066, MS 261, MS 341, MS 361,MS 362, MS 441, MS 650, MS 660 and MS 661 andCut Quik / Concrete Saw models: TS 410 and TS 420.Size: 15mm X 22mm OD X 4mm.NOTE: You will need to confirm themeasurements of your old seal to see if they match.

622-274 9640-003-1570 Oil Seal (Flywheel / Mag side) Fits chain saw models:041, 042, 048, 051, 075 & Cut Quik models:TS400, TS410, TS420, TS480i, TS500i, TS510 and TS760.Size: 15mm X 24mm OD X 7mm.

622-241 9640-003-1600

Oil Seal (Clutch Side). Fits chain saw models: 024, 026, 028, 034, 036, 044, 046, 084, MS 240, MS 241, MS 260, MS 261, MS 340, MS 341, MS 360, MS 361, MS 362, MS 440, MS 441, MS 460 and MS 461. Trimmer models: FS360, FS420, FS500, FS550 and SR400. Stihl Blower models: BR 320, BR 340, BR 380, BR 400, BR 420 blowers; Cut Quik saw model: GS 461; Stihl Sprayer models: SR 320, SR 340, SR 400 and SR 420. Size: 15mm X 29.6mm OD X 4mm HT. NOTE: You can find (1) 622-241 oil seal in our 640-268 gasket set.

16-61

STIHL continuedSTIHL continued


C C

622-249 9640-003-1610Oil Seal (PTO & Mag side)Fits chain saw models: 08 / 08S & Cut Quik models: TS350and TS360.Size: 15mm X 35mm X 7mm.

622-261 9639-003-1743Oil Seal Fits chain saw models:029, 039, MS 290, MS 310 and MS 390.Size: 16.7mm ID X 30mm OD X 4.2mm HT.

622-076 9640-003-1745Oil Seal (Magneto and PTO Side)Fits concrete / cut quik saw models:TS400, TS460, TS700 and TS800.Size: 17mm ID X 28.15mm OD X 5mm Thick.

622-264 9640-003-1850 Oil Seal (Clutch side) Fits chain saw models:064, 066, MS650 and MS660.Size: 17mm X 32.9mm OD X 3.6mm.NOTE: You will need to confirm themeasurements of your old seal to see if they match.

622-266 9640-003-1880Oil Seal (PTO side) Fits chain saw models: 038 and 038 Super. Size: 17mm X 39.5mm OD X 5mm

622-257 9629-003-2900Oil Seal Fits chain saw models: 050, 051, 075 & 076and Cut Quik models: TS510 and TS760.Size: 25mm X 47mm OD X 7mm.

615-514 0000-350-6202 1130-350-6200

Primer Bulb AssemblyFound on concrete / cut off saw models:TS400 and TS800; Mounting hole: .576”(Uses our 615-028 replacement primer bulb).

615-510 4238-350--6201Primer Bulb AssemblySize: 1” OD X 1-3/8” HT.Found on Stihl concrete / cut off saw models:TS410 and TS720. Fits Stihl Blower models:BR350, BR430 and SR350, SR430, SR450.Mounting hole: .890”(Uses our 615-028 replacement primer bulb).

135-110 1128-405-1000Spark Plug Boot with SpringFor chain saw models: 009, 010, 011, 012, 017, 018, 020, 021, 023, 024, 025, 026, 029, 034, 036, 039, 044, 046, 056, 064, 066, 084, 088, MS170, MS180, MS192T, MS210, MS230, MS240, MS250, MS270, MS290, MS310, MS340, MS341, MS360, MS361, MS380, MS390, MS440, MS441, MS460, MS640, MS650, MS660 and MS880.

135-061 Universal

Spark Plug Wire (5mm OD)Plug Wire for chain saw models: 08, 08S and Cut Quik Saw models:TS-350 and TS-360. Quality black hypolon outer case with COPPER (not carbon) inner wire. 5mm Spark (Priced and Sold in 10 meter / 33 FT rolls)

650-141 1118-648-04001119-648-0400

Sprocket Side CoverFor chain saw models: 024 and 028 (new).

650-154 1125-640-17011125-648-0402

Sprocket Side Cover Fits chain saw models: 024, 026, 028 Super, 029,034, 036, 038, 038 Magnum,039, 044, 046, 064, 066, MS240, MS260, MS340, MS360, MS380, MS440, MS460, MS640, MS650 and MS660. (Made of Cast Metal).

650-124 1108-640-1705Sprocket Side CoverFor chain saw models: 08 and 08S. Complete with tank cover.

681-134Sprocket Needle BearingFits chain saw models: 009, 010, 011, 012, 021, 023, 024, 025, 026, 34 and 36 (PRIOR TO X25809074). (Size: 10mm X 13mm X 10mm) NOTE: This bearing will not replace the plastic needle bearing type used on newer models.

681-128Sprocket Needle Bearing Fits models: 028 series.(Size: 10mm X 13mm X 23mm)

681-125 0000-993-3008

Sprocket Needle Bearing For chain saw models: 08S and Cut-Quik models: TS350 and TS360. (Size: 15mm X 18mm X 17mm) NOTE: This bearing will not replace the plastic needle bearing type used on newer models.

681-127Sprocket Needle Bearing Fits chain saw models:038. 042, 048 (Spur Only)(Size: 12mm X 16mm X 24mm)


16-62



C C

681-126 9512-933-2382

Sprocket Needle Bearing Fits chain saw models: 044, 046, MS440,MS460, 064, 066, MS360, MS361, MS362,MS440, MS441, MS460, MS461, MS640 and MS660. NOTE: Will also replace the original STIHL (plastic cased needle bearing) in the MS390. (Size: 10mm X 16mm X 12mm)

681-129Sprocket Needle BearingFits our chain saw sprockets fitting on models: 084, 088. (Size: 12mm X 17mm X 13mm)

671-110

Sprocket Nut Fits chain saw models: 08, 08S; also found on older Cut Quik model: TS350

672-110Flywheel Nut Fits chainn saw models: 08, 042, 045, 056, 070, 090; also found on Cut Quik models: TS350 & TS360

CE4MC56 3670-005-0056(Rotary# 7111056)

Saw Chain Loop (10” Bar)1/4” pitch X .043 gauge X 56 drive link count

Fits STIHL battery powered chainsawsand pole saws, using a 10” guide bar.Used on Stihl model: MS150 TC-E etc.(Replaces Stihl# 3670 005 0056 / 71PM3-56).

CE4MC64 3670-005-0064(Rotary# 7111064)



CE4MC72 3670-005-0072(Rotary# 7111072)




655-025 1123-080-2104

Starter Assembly For chain saw models:021, 023, 023, MS210, MS230 and MS250. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on.(Made of Nylon).

655-024 1121-080-2101

Starter Assembly For chain saw models:024, 026, MS240and MS260.

This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on.(Made of Nylon).

655-029 1127-080-2103 / A

Starter Assembly For chain saw models:029, 031, 039, MS290,MS310, MS390.

This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of Nylon).

655-034 1125-080-2105

Starter AssemblyFor chain saw models: 034, 034 AV, 034 Super,036, MS340 and MS360.

This aftermarket assembly comes complete with housing,starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of metal).

655-036 1135-080-2102

Starter AssemblyFor chain saw models:MS341 and MS361.

This aftermarket assembly comes completewith plastic housing, starter pulley, spring, rope,pawl, starter handle etc. Just needs to be bolted on.

16-63



C C


655-038 1119-080-1800

Starter Assembly For chain saw models:038 series.

This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of cast metal).

655-044 1128-080-2100 / 1128-080-2102 1128-080-2104

Starter Assembly For chain saw models:044, 046, MS440and MS460.


655-066 1122-080-2110

Starter Assembly For chain saw models:066, MS650 andMS660.


655-035 1108-080-2101 / 1108-080-2115

Starter Assembly For chain saw model: 08 & 08S and Concrete/ Cut Quik saw model:TS350 and older TS360.

This aftermarket assembly comes complete with plastic housing, metal starter pulley, spring, rope, pawl, elasto starter handle etc. Just needs to be bolted on. (This assembly is the newer - 1 nylon starter pawl set up).

655-040 4223-190-0401

Starter Assembly For concrete saw / cut quik saw model: TS400. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on. (Made of Nylon)

655-042 4238-190-0300 / 4238-190-0301 4238-190-0302 / 4238-190-0402B

Starter AssemblyFor concrete saw cut quik saw models: TS410 and TS420.This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on. (Made of Nylon)

560-119Starter Handle For chain saw models: 010, 011, 015,021, 028, 031 and 032.

560-213 1121-195-3400

Starter Handle For chain saw models: 021, 023, 024, 026, 028,028 Super, 034, 034 Super, 036,044, 046, 064, 066 (New style),Concrete saw models: TS350, TS360, TS510 and TS360

560-118 1110-195-3400Starter HandleFor chain saw models: 08, 038, 041, 042,050, 051, 056, 070,075 and 090. (Old style)

560-120 1113-195-82000000-190-3400

Elasto Starter Handle and RopeFor many Stihl saws. Medium starter handle with rubber buffer to help obsorb the kick that you get from some of the larger cc saws. Rope diameter is 4mm X 36 inches long.

560-121 1122-190-3400Elasto Starter Handle and Rope For many Stihl saws.Large starter handle with rubberbuffer to help obsorb the kick thatyou get from some of the larger cc saws. Rope diameter is 4.5mm X 38 inches long.

560-170 1117-195-7200Starter Pawl (nylon)For Stihl chain saw models: 08, 038, 042, 048, 051, 056 and 070 (old style). Size: 1.11” overall length X

.375” overall height not including positioning nub.




16-64


C C

560-202 1124-195-04011124-195-7200

Starter Pawl (nylon)For Stihl chain saw models: 038, 041, 042, 045, 048, 050, 051, 056, 064, 066, 070, 076, 08S, 084, 088, MS380, MS640, MS650, MS660, MS880; also fits Cut Quik Saw models TS350 and TS360.Size: 1.12” overall length X .475” overall height not including positioning nub. (newer style)

560-203 1125-195-7200

Starter Pawl (nylon)For chain saw models: 009, 010, 011, 012, 017, 018, 019T, 020, 020T, 021, 023, 024, 025, 026, 028, 029, 034, 036, 039, 044, 046, MS170, MS180, MS190T, MS191T, MS192T, MS200, MS200T, MS210, MS230, MS2400, MS250, MS260, MS270, MS290, MS310, MS3400, MS341, MS360, MS 361, MS440 and MS460.

560-784 0000-195-72004116-195-7200

Starter Pawl (metal pin)Fits concrete saw model: TS400

560-199 4116-195-7200Starter Pawl (nylon)Fits Trimmer models:FR220, FS106, FS160, FS180,FS220, FS280; Back Pack Blowersmodels: BR320, BR320L, BR340, BR340L,BR380, BR400, BR420, BR500, BR550, BR600,2 cycle Tillers and more.(For use with our 630-095 pawl spring).

630-095 1118-195-3500Spring Clip / Pawl Spring Fits chain saw models: 009, 010,011, 012, 024,026, 028, 032 old style;Also found on Trimmers, Blowers, 2 cycle Tillers and more. (For use with our 560-111 and 560-199 starter pawls).

630-111 1128-195-3500Spring Clip / Pawl Spring Fits chain saw models: 024, 026, 028, 034, 036, MS360, 039, MS390, 044, MS440, 046, MS460 etc. (For use with our 560-203 starter pawls).

630-118 1124-195-3500Spring Clip / Pawl Spring Fits chain saw models: 064, 066, MS640, MS660 and 084. Size: 1-3/4” overall length X 1-1/8” approximately(For use with our 560-202 starter pawls).

630-179 1117-195-3500Spring Clip / Pawl SpringFits chain saw models: 038, 041, 042, 045, 048, 050, 051, 056, 070, 076, 08S, MS380 & MS381.



560-189 1123-195-0400Starter Pulley (nylon)Fits chain saw models: 017, 018, 019, 020, 021, 023, 025,MS170 / 180 / 190 / 191 / 192 / 200MS210, MS230 and MS250. Measures: 2-1/2” OD (2) pawl pulley

560-190 1118-190-1000Starter Pulley (nylon)For chain saw models: 028 and 024 (old style). Measures: 2-9/16” OD (1) pawl pulley

560-237 1128-195-0400Starter Pulley (nylon) For chain saw models: 029, 034, 036,039, 044, 046, MS261, MS271, MS290,MS291, MS310, MS311, MS340, MS341,MS360, MS361, MS362, MS390, MS391,MS440, MS441, MS460.Measures: 2-11/16” OD (2) pawl pulley

560-201 1125-195-04001125-195-0401

Starter Pulley (nylon)For chain saw models: 024, 028 (new-style) and 034. Measures: 2-3/4” OD (2) pawl pulley

560-224 1117-007-10141117-195-0402

Starter Pulley (metal)For chain saw models: 038, 041, 042, 045, 048, 051, 056, 08,070, 075, 076, and Cut Quik models: TS350, TS360, TS510 & S760. Measures: 3-1/8” OD (2) pawl pulley(Uses our 560-202 & 630-179)

560-146 1107-190-1000Starter Pulley (metal)For chain saw models: 08, 08S and 070. Measures: 3” OD (2) pawl pulley

560-200 1122-195-0400

Starter Pulley (nylon)For chain saw models: 08S, 051, 064, 066, MS640, MS650 & MS660. Measures: 2-27/32” OD (2) pawl pulley

560-225 4223-190-1001

Starter Pulley With brass bushing.For Stihl Cut Quik / Cut off saw models:TS400, TS410 and TS420 Cutquik saws.Measures: 3” (76.82mm) Bottom OD X 2.74” (69.63mm) Top OD X .412 (10.47mm) ID / Bore. (1) pawl pulley. Uses our 560-784 Starter Pawl.



16-65


C C

560-116 0000-961-5116Starter Ring (nylon)For chain saw models:08S, 041, 045 & 070. Size: 2-1/4” OD

625-500 1111-195-1600Starter SpringFor chain saw models: FS08, FS410, 410AV, 410 AVE (...5816400)

625-501 1113-195-1600Starter SpringFor chain saw models: 030 and 031.

625-502 1116-195-1600Starter SpringFor chain saw models: 009, 010, 011 (...X12725130) and 015.

625-503 1118-190-0600Starter SpringFor chain saw models: 024, 026, 028, 032 and 034.

625-504 1114-190-0600Starter SpringFor chain saw model: FS150, 151, 200AV and 200AVSE.

625-506 1115-190-0600Starter SpringFor chain saw model: 045. (...#5919431)

625-507 1160-190-0600Starter SpringFor chain saw models: 08, 070, 090, 510For Cut Quik model: TS350 (old model - wide spring).

625-508 1117-190-0600Starter SpringFor chain saw model: 042.

625-510 1110-190-0600Starter SpringFor chain saw models: 040 and 041 (...#2663618).

625-509 1117-190-0601Starter SpringFor chain saw models: 038, MS380, 041 (#5816401...), 042 (after serial# 5676790), 045(before serial# 5919431...), 048, 050, 051(after serial# 674961...), 056, 070, 075, 076and Cut Quik models: TS-350, TS-360, TS510 & TS760.

625-511 1120-195-1600

Starter SpringFor chain saw models: 009, 010, 011 (X12725130...) and 012.

625-516 1128-190-0600Starter SpringFor chain saw models: 036, 044 and 046.

625-517 1122-190-0600Starter SpringFor chain saw models: 064 and 066.

625-522 1122-190-0605

Starter Spring For chain saw models: 066, MS650 and MS660. Comes complete with nylon case.

625-518 1124-190-0600

Starter SpringFor chain saw model: 084.

625-519 1129-190-0600

Starter SpringFor chain saw models: 017, 021, 023, 025, 029 and 039.

625-520 4223-190-0600

Starter SpringFor Cut Quik Saw / Concrete Saw model: TS400. Measures: 2.348” diameter

625-521 1129-190-0601

Starter SpringFor chain saw models: 017, 018, 019 T, 020, 020 T, 021, 023,025, 029, 034, 036, 039, 044, 046,MS 170, MS 171, MS 180, MS 181,MS 190 T, MS 191 T, MS 200, MS 200 T, MS 210,MS 211, MS 230, MS 250, MS 270, MS 280, MS 290, MS 310, MS 340, MS 360, MS 390, MS 440, MS 460. Replacement spring for our 655-034 & 655-044 starter assemblies.

625-526 4282-190-06004238-190-06014282-195-0300

Starter SpringFor Cut Quik Saw / Concrete Saw model: TS410 and TS420. Measures: 2.479” diameter


16-66


C C

630-300 1117-182-4500

Torsion Spring Fits Stihl chain saw models:017, 018, 019 T, 021, 023, 024,025, 026, 028, 029, 032, 034, 036,038, 039, 042, 044, 046, 048, 064, 066, 084, 088, MS170, MS171, MS180, MS181, MS190 T, MS191 T, MS210, MS211, MS230, MS240, MS250, MS260, MS270, MS280, MS290, MS310, MS311, MS340, MS341, MS360, MS361, MS362, MS380, MS381, MS390, MS391, MS440, MS460, MS461, MS640, MS650, MS660, MS661, MS780, MS880; also on Concrete saw / Cutquik model: TS400.

630-321 1128-182-1005

Throttle TriggerFits chainsaw models: 021, 023, 025, 029,039, 044, 046, MS210, MS230, MS250,MS290, MS310,MS390, MS440, MS460, MS461.(Also see our 630-326 Trigger Interlock).

630-326 1117-182-0805

Throttle Trigger InterlockFits chainsaw models: 021, 023, 024,025, 026, 028, 029, 034, 036, 038, 039, 042, 044, 046, 048, 064, 066, 084, 088, MS210, MS230, MS240, MS250, MS260, MS290, MS310, MS340, MS360, MS380, MS381, MS390, MS440, MS460, MS461, MS640, MS650, MS660, MS780, MS880 saws.(Also see our 630-321 Throttle Trigger).

630-323 4238-182-0800Throttle Trigger InterlockFits concrete / cut quik saw model:TS410, TS420, TS480i and TS500i .

630-327 4238-182-1000Throttle TriggerFits concrete / cut quik saw models:TS410 and TS420.

654-143 1121-790-17011121 790 1714

Tube Handle For chainsaw model:024 and 026 and MS 260chainsaws with metal handlebars.

654-139 1118-790-1700

Tube Handle For chain saw models: 028 and 028 Super.

654-137 1119-790-1700

Tube HandleFor chain saw models: 038 and 038 Super.



654-128 1110-790-1510Tube HandleFor chain saw model: 041 (old style).

654-133 1110-790-1716Tube Handle For chain saw model: 041 (new style).

654-126 1108-790-1500Tube Handle For chain saw model: 08S and Cut Quik models: TS350 & TS360.

654-145 1122-790-17001122-790-1750

Tube Handle For chain saw models: 064, 066 and MS660.

654-125

Wrap HandleFor chain saw models: MS230 and MS250.

654-140 1128-790-17501128-790-1753

Wrap HandleFor chain saw models: 044, 046, MS440, MS460and MS461; also fits model:GS 461 concrete saw..

705-574T Wrench / ScrenchFits models: 009, 010, 011, 015,020, 021, 023, 024, 025, 026, 028,031, 032, 034, 036, 038, 041, 048and 056.

Bar nut= 1/2” or 13mm. Spark plug = 3/4” or 19mmA = 6-3/4”, B = 1-1/16”, C = 1





16-67



C C

705-590

T Wrench / ScrenchFits models: 044, MS440, 046,MS460, 064, MS640.

Bar nut= 1/2” or 13mm. Spark plug = 3/4” or 19mmA = 7”, B = 1-5/8”, C = 1”

705-635 Carlton# 41C1719

T Wrench / Scrench.Fits Stihl chiansaw models: 051,076, TS350, TS360 and TS510.Also fits Dolmar models:122, 144 and Echo 1001 & others.

Bar nut= 11/16” or 17mm. Spark plug = 3/4” or 19mmA = 6-3/4”, B = 1-5/16”, C = 1-5/16”

705-525

T Wrench / ScrenchFits chain saw models:08S, 051, 051, 075, 090and Cut Quik models:TS350 & TS360.

Bar nut= 11/16” or 17mm. Spark plug = 13/16” or 21mmA = 7”, B = 1-11/16”, C = 1-5/8”

705-202 5910-890-2400

Torx WrenchFor bolts foundon Stihl equipment.

Special 6 - sided torx head. NOTE: Picture shows a close up of torx end for reference

705-592 Carlton# 41C1319TOregon# 57-019

T Wrench / ScrenchUsed on Husqvarna and Stihl cut quik / cut off / concrete saws. Fits Stihl concrete / cutquik saw models: TS350, TS350AVE, TS360, TS400, TS460, TS700 and TS800.

Size: 1/2” (13mm) Bar Nut X 3/4” (19mm) Spark Plug X (B = 2”) + (C = 1”) = 3” total with a 7-3/4” long handle. T27 Torx End.

A

B

C

705-634

T Wrench / ScrenchFits most new Stihl chain saws.

Size: 11/16” (17mm) Bar Nut X 3/4” (19mm) Spark Plug X (B = 1-7/16”) + (C = 1-1/2”) = 2-15/16” total with a 7-3/4” long handle. T27 Torx End.

705-190 0812-540-1111

T27 Power Bit / Tork WrenchFits Torx Wrench / T27 Power Bit.(3-1/2” Long). Fits most Torx headbolts found on Stihl equipment. 6 - sided torx head.

705-194 0812-540-1112

T27 Power Bit / Tork WrenchFits Torx Wrench / T27 Power Bit.(6” Long). Fits most Torx headbolts found on Stihl equipment. 6 - sided torx head.

TANAKA625-850 779 00601 203Starter Spring For chain saw models: ECS-350 and 355.

FOR MORE TANAKA STARTER SPRINGSsee our web site @ www.bantasaw.com

PLEASE VISIT [email protected]

You can email your inquires to us [email protected]

16-68


CCHAIN SAW ACCESSORIES - O.E.MHAIN SAW ACCESSORIES - O.E

Documents

Transcript of CCHAIN SAW ACCESSORIES - O.E.MHAIN SAW ACCESSORIES - O.E