Canon 6000 series

When taking cartridge out of the printer, makesure to seal the ink outlet with Scotch tape before refilling the ink.

Step 1

Step 2

Make a needle hole on top upper right-hand corner of the ink resevoir. Don’t make hole toobig.

Canon 600 series

Refill ink slowly. Do not fill the ink to exceed the level of the hole you just made.

After fully reflling the resevoir, clean the surface with a dry paper towel and seal the refilling hole with Scotch tape.

Step 3

Step 4

Canon 600 series

After refilling the ink and sealing therefilling hole, the cartridge looks like this.

Remove the tape from the original ink outlet before inserting the refilled cartridge into the printer. Wipe the ink outlet with a paper towelfor any leaks.

Step 5

Step 6

Canon 4000 series

On the bottom of the cartridge you will seeink refilling hole/s. Do not pierce the needleinto the refilling hole/s. Hold the needle pointjust above the refilling hole/s and release theink drop by drop into the refilling hole/s.The refilling hole/s has a filter which will absorbthe refilling ink.

Color Cartridge

Black cartridge

Same procedure as Step 1

Epson cartridge

Take the cartridge out of the printer,and clean the residual ink with a dry paper towel and sealthe original ink outlet with the Scotch tape to prevent any leaking when refilling the cartridge.

Step 1

Step 2

Tear off the top hot-sealed original film from the cartridge. You will notice a color chamberrefilling hole for each color. Be careful NOT to refill ink into the wrong color chamber. Forgrey-colored cartridges you can check ink color with a cotton bud or tooth pick.

Pierce the needle into the rear refilling hole of the color chamber. Refill the ink SLOWLYto prevent any formation of air bubbles.

After refilling the ink, only seal the refiling holes of the color chambers with Scotch tape. DO NOT SEAL THE ENTIRE TOP COVER.Tap the refilled cartridge few times to removeany trapped air inside the cartridge.

Leave this area open

Step 3

Step 4

Step 5

Remove the tape from the original ink outlet.Please use a dry paper towel to wipe any leakagefrom the outlet and before inserting the cartridgeinto the printer.

It is suggested not to use this refilled cartridgeimmediately after refilling

Ink outlet

Remove te top rubber ball bearing from the holein the cap by using a thumb tack.

Hewlett Packard51626A(black)

Step 1

Pierce the refilling needle into this hole. Do not insert the needle too deep to avoidpunctuating the air bag inside. Place a dry paper towel under the original ink outlet whenrefilling ink to absorb any leakage.

Step 2

Use a syringe with a special rubber attachmentand place it into the “Aperture C” located in the bottom of the cartridge as shown in the abovepicture, to suck out any air bubbles in the cartridge.If the air is not sucked out completely the cartridgemight leak.

Step 3

Aperture “C”

Printhead

IMPORTANT PROCESS

Place the ball bearing into its originalposition in the plastic cap.

Step 4

Check the ink outlet with a dry paper towelto ensure the ink is flowing.In case of continuous leakage, repeat “Step 3”to remove any remaining air bubbles.

Step 5

Hewlett Packard51625A(color)

The filler holes of the cartridge are loacatedunder the top plastic cover cap. Use a thin phillips screwdriver to prise open the cover.

Filling the ink into the center correct color hole of each ink chamber. Be careful NOT to refillthe ink into the wrong color chamber.

Step 1

Step 2

After refilling check the original ink outlet with a dry paper towel to ensure that ink isflowing.

Replace the prised top plastic cover into its original position and seal firmly with theScotch tape.

Step 3

Step 4

Lexmark

Pierce the needle into the top small holeof the cartridge. Do not over fill with inkas it might leak.

Using a dry paper towel to check if the inkflowing from the original ink outlet beforeinserting the cartridge into the printer.

Step 1

Step 2