Cable List Rnc450

7/28/2019 Cable List Rnc450

http://slidepdf.com/reader/full/cable-list-rnc450 1/40

Nokia Siemens Networks

WCDMA RNC Rel. RN6.0, Site

Documentation, Issue 01

Cable Lists for RNC450

DN0638091

Issue 05

Approval Date 2011-01-06

Confidential



2 DN0638091

Issue 05


Id:0900d80580819ce4

Confidential

The information in this document is subject to change without notice and describes only the

product defined in the introduction of this documentation. This documentation is intended for the

use of Nokia Siemens Networks customers only for the purposes of the agreement under whichthe document is submitted, and no part of it may be used, reproduced, modified or transmitted

in any form or means without the prior written permission of Nokia Siemens Networks. The

documentation has been prepared to be used by professional and properly trained personnel,

and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes

customer comments as part of the process of continuous development and improvement of the

documentation.

The information or statements given in this documentation concerning the suitability, capacity,

or performance of the mentioned hardware or software products are given "as is" and all liability

arising in connection with such hardware or software products shall be defined conclusively and

finally in a separate agreement between Nokia Siemens Networks and the customer. However,

Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions

contained in the document are adequate and free of material errors and omissions. Nokia

Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which

may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO

EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-

TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-

RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED

TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY

OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION

IN IT.

This documentation and the product it describes are considered protected by copyrights and

other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark

of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respectiveowners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2011. All rights reserved

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources

of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle

this product and only after having carefully read the safety information applicable to this

product.

The safety information is provided in the Safety Information section in the “Legal, Safety

and Environmental Information” part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur ProduktsicherheitVon diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder

andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch

geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-

anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal,

Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-

satzes.



DN0638091 3


Id:0900d80580819ce4

Confidential

Table of contentsThis document has 40 pages.

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1 About Cable Lists for RNC450. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.1 Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Identifying subracks, connectors and cables . . . . . . . . . . . . . . . . . . . . . . 9

2.1 Numbering system of the subrack shelves and cable connectors. . . . . . 9

2.1.1 Locking pegs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.2 Categories of cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.2.1 Interconnection cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.2.2 Site cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.3 Identifying cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.4 Cabling l ists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3 Intracabinet cables for the RNAC cabinet . . . . . . . . . . . . . . . . . . . . . . . 15

3.1 RNAC power cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.2 RNAC control and bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.3 RNAC LVDS cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.3.1 RNAC synchronisation and LVDS cables . . . . . . . . . . . . . . . . . . . . . . . 19

3.4 LAN cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.5 RNAC alarm and synchronisation cables . . . . . . . . . . . . . . . . . . . . . . . 23

3.6 RNAC IP upgrade cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4 Intracabinet cables for the RNBC cabinet . . . . . . . . . . . . . . . . . . . . . . . 28

4.1 RNBC power cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.2 RNBC control and bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.3 RNBC synchronisation cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4.4 RNBC IP upgrade cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5 Intercabinet cables from RNBC to RNAC . . . . . . . . . . . . . . . . . . . . . . . 33

5.1 Intercabinet LVDS cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.2 Intercabinet HMS and timing cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

6 Physical cable equipping positions and SW port connection coordinates .

38



4 DN0638091


Id:0900d80580819ce4

Confidential

List of figuresFigure 1 Notations used in the cabling lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 2 Example of marking system for the cables . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 3 Routing of line timing cables CA_060 - CA_062 and CA_067 - CA_069 18

Figure 4 CPSY-A, CPSY-B and CPAL-A panel positions in RNAC . . . . . . . . . . . 25

Figure 5 Routing of intercabinet LVDS cables CB0_001 - CB0_032 . . . . . . . . . . 35

Figure 6 Routing of HMS cables CB0_040 - CB0_041 and timing cables CB0_050 -

CB0_051 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 7 Notations used in table Physical cable equipping positions and corre-

sponding SW port connection coordinates . . . . . . . . . . . . . . . . . . . . . . . 39



DN0638091 5


Id:0900d80580819ce4

Confidential

List of tablesTable 1 Columns of cabling list columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 2 RNAC CPD120-A power cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 3 RNAC control cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 4 OMU/WDU SAS/PCIe bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 5 RNAC HMS bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 6 RNAC Timing bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 7 RNAC default line timing cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 8 RNAC FSYNC and 2N_ACT cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 9 RNAC SFU LVDS cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 10 RNAC NIS1P protection switch cables . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 11 TSS3 synchronisation cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 12 ESA40-A/ESA24 0 LAN cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 13 ESA40-A address setting modules . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Table 14 RNAC alarm and synchronisation cables to rear panels CPSY-A, CPSY-B

and CPAL-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 15 NPGE(P) 0 IP upgrade cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26




Table 19 RNBC CPD120-A power cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 20 RNBC control cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 21 RNBC HMS bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 22 RNBC Timing bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 23 RNBC 2N_ACT cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Table 24 RNBC NIS1P protection switch cables . . . . . . . . . . . . . . . . . . . . . . . . . 29





Table 29 Intercabinet LVDS cables from RNBC and RNAC . . . . . . . . . . . . . . . . 33

Table 30 Intercabinet HMS and timing cables from RNBC and RNAC . . . . . . . . 36

Table 31 Physical cable equipping positions and corresponding SW port connection

coordinates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40



6 DN0638091


Id:0900d80580819ce4

Confidential



DN0638091 7

Cable Lists for RNC450 Summary of changes

Id:0900d8058083628e

Confidential

Summary of changesChanges between document issues are cumulative. Therefore, the latest document

issue contains all changes made to previous issues.

Changes between issue 4-0 and 05

NEMU and RRMU related information is removed. CCP1D-A, HDS-C and ESA40-A

related information is added.

SCSI cables table is removed. PCIe and SAS tables are added.

Changes between issue 3-0 and 4-0

Add NPGE(P) cables in RNAC and RNBC cabinets.

Changes between issue 2-0 and 3-0

CA_304 CPSY-B cable positions corrected.



8 DN0638091


Id:0900d80580440775

Confidential

About Cable Lists for RNC450

1 About Cable Lists for RNC450Cable Lists for RNC450 provides a list of all the intercabinet and intracabinet cabling

installed in the RNAC and RNBC cabinets in RNC450.

1.1 Related documentation

Equipment Lists

For more detailed information on the RNC cabinet mechanics, see Equipment Lists for

RNC450.

Engineering Description

For basic information on, for example, RNC installation planning, see Engineering

Description.

Installation Manual

For detailed information on RNC hardware installation, see Installing the MGW and

RNC.

http://equip_list_rnc450.pdf/


http://dn0938143.pdf/












DN0638091 9

Cable Lists for RNC450 Identifying subracks, connectors and cables

Id:0900d80580455505

Confidential

2 Identifying subracks, connectors and cables

2.1 Numbering system of the subrack shelves and cable con-nectors

The positions of all connectors mentioned in this document are numbered by the co-

ordinate system introduced here. The equipment cabinets, subrack positions, and cable

connectors in the subracks have individual co-ordinate systems to facilitate the installa-

tion of subracks and the connection of cables.

The cabinet's subrack positions are assigned with numbers from 1 to 4 from the top

down. The subrack is identified by a sticker attached to its upper left corner.

Each subrack has twenty slots for plug-in units. The subracks are marked with the

position numbers of the plug-in units. Seen from the front, each subrack includes

eighteen slots dimensioned for full-height plug-in units, numbered from 1 to 18 from leftto right. The last two slots are for two half-height plug-in units located one on top of the

other. The upper slot is numbered 19 and the lower one 38.



10 DN0638091


Id:0900d80580455505

Confidential

Identifying subracks, connectors and cables

Figure 1 Notations used in the cabling lists

2.1.1 Locking pegs

Each connector is provided with locking devices (for example locking pegs or screws)

that fasten the cable connector securely to the subrack.

The connector's locking pegs are placed in the same positions in each subrack type,

regardless of the subrack's position in a given cabinet. If the subrack includes supple-

mentary locking pegs, they can be used as spare parts.

IPA2800 RNC / MGW cabinet,

seen from the front

Slot position number

CA_020 OMU 0 1.0B 16.4X WDU 0-0 1.0B 17.3H CJA002 SCSI bus 0

CA_021 OMU 0 1.0B 16.5D WDU 0-0 1.0B 17.3O CJB002 SCSI bus 0

FU Connector FU Connector Type Use

Equip No. CABLE FROM CABLE TO

Connector Type ACE

1.0B 16.4X

1 2 3F = FRONTB = BACK 4

DN05158647

Subrack in position 1 seen from the rear

A

C

E

G

J

L

N

P

R

T

V

X

Z

Z ABCDEF

3

1

2

3

4

5

B

A

B

A

B

Connector Type BDF

B

D

F

H

K

M

O

Q

S

U

W

Y

Z ABCDEF

4

12345678910111213141516171819

2

Note

1



DN0638091 11


Id:0900d80580455505

Confidential

2.2 Categories of cables

The cabling of an exchange consists of interconnection cables (intermediate cables)

and site cables (outgoing cables) as described below.

2.2.1 Interconnection cables

The interconnection cables comprise all the cables inside each cabinet and between the

cabinets which form a single exchange. The interconnection cables are cut to length and

equipped with connectors. They include:

• power distribution cables

• ATM connection cables

• Hardware Management Bus (HMS) cables

• synchronisation and timing cables

• SCSI cables between storage units and their master units

• LAN/Ethernet cables

Intracabinet cables

The interconnection cables between different subracks located in the same cabinet run

from one subrack to another along the walls and cabling shelves of the cabinet. These

cables are delivered completely installed in the cabinets.

Intercabinet cables

The interconnection cables running between different cabinets are led directly from one

cabinet to another on cable shelves located behind the cabinets. These cables must be

installed at the site. The interconnection cables are delivered as prefabricated cable

sets.

2.2.2 Site cables

The site (outgoing) cables are all the cables that leave the exchange. They include:

• trunk circuit cables from the network interfaces

• power supply cables

• grounding cables

• I/O cables

• TCP/IP cables to the Network Management system

The site cables are connected directly to the plug-in units, or to connector panels located

at the rear of the cabinets, or to the connectors panels in the cabling cabinet. These

cables must be installed at the site.

The site cables can be routed to the environment through the opening at the bottom

(raised floor installations) or top plate (normal installation) of the EC216. These cables

must be installed at the site.

All the cables entering the cabinet(s), except for the DC power feed cables, must have

a shield or protective wires which are grounded to the frame of the exchange at the con-

nectors in the cabinets.

Note that the site cables are not delivered in sets, but they must be ordered separately.

The site cables are designed for each delivery and therefore they vary in length depend-

ing on the delivery. They are not included in the standard documentation.



12 DN0638091


Id:0900d80580455505

Confidential


2.3 Identifying cables

The equipping reference is located on the Cable Identification Label (marked b) in Figure

Example of marking system for the cables, below).

The first part of the equipping reference specifies the cable list where the cable is men-

tioned. The second part gives the sequence number within that list.

The equipping reference of the cables is based on the cabinet (type) name in which the

cable is connected. There are two main groups:

1. Cables whose both ends are connected in the same cabinet (intracabinet

cables).

The equipping information is expressed: [Cabinet type_sequence number]. ”CA_123”.

There may be several identical cables of this type in a single Network Element, but only

one within the same cabinet.

2. Cables which originate from one cabinet and end in another (intercabinetcables).

The equipping information is expressed: [Cabinet type, cabinet index_ sequence num-

ber].”CBn_123”. There may be only one of each individual cable of this type in a single

Network Element.

In the RNC, all intercabinet cables connect from RNBC to RNAC.

The cabinet where the cable begins (starts in) determines the [cabinet type, cabinet

index] part of the equipping reference.



DN0638091 13


Id:0900d80580455505

Confidential

Figure 2 Example of marking system for the cables

2.4 Cabling lists

The cables are listed in tables. Each cable has its individual number. This number and

the address of both ends of the cable are given. Both the name of the functional unit to

which the end of the cable is connected and its co-ordinate are given in a table. The

columns of the table are used as follows:

DN99632985

b) Cable identification label

) A letter 'C' after the number indicates centimetres (cm) instead of decimetres (dm).

Example

a) Equipping number of cable, e.g.

Sequential number

ITEM NAME:CJA002 LOT ID: 3G9912

Alias name

Fixed length (dm)

Item identifier

Separators

Factory symbol

Year / Week

Interchangeability / version

C19179 .......... A01

CA-020

CA_020

a)

b)

CA_020

a)



14 DN0638091


Id:0900d80580455505

Confidential


The lengths of intracabinet cables in deliveries may be different from those given in this

document.

Equip. No. CABLE FROM CABLE TO

FU Conn. FU Conn. Type Use Notes

Equip. No. The equipping number is the individual number of the cable. Both ends of the cable

bear a label with this number on it.

CABLE FROM

(RNBC)

In case of intercabinet cabling, the text CABLE FROM RNBC indicates that the cable

originates from the RNBC cabinet.

CABLE TO

(RNAC)

In case of intercabinet cabling, the text CABLE TO RNAC indicates that the cable ends

in the RNAC cabinet.

FU These columns give the name of the functional unit housed in the subrack where the

ends of the cable connect to. For example MXU.

Conn.(ector) These columns give the co-ordinates of the connectors where the ends of the cable

are connected.

Type The column gives the type (the first three letters) and length of the cable (the following

two or three numbers) in decimetres (10 cm), or if marked with a C, in centimetres. For

instance, CHA010 is a cable of CHA type which is 100 cm long.

Use The column gives the type of signal carried by the cable, for example PDH line.

Notes This column is for additional information.

Table 1 Columns of cabling list columns



DN0638091 15

Cable Lists for RNC450 Intracabinet cables for the RNAC cabinet

Id:0900d80580836290

Confidential

3 Intracabinet cables for the RNAC cabinetThis chapter presents the intracabinet cabling for the RNAC cabinet in RNC450.

Single cabinet figures show the RNAC cabinet. Two-cabinet figures show the RNBC andRNAC cabinets from left to right, unless otherwise indicated.

t The lengths of intracabinet cables in deliveries may be different from those given in this

document.

3.1 RNAC power cables

3.2 RNAC control and bus cables

Equip.

No.

CABLE FROM CABLE TO

FU Conn. FU Conn. Type

CA_001 CPD120-A UB2 0.10B P1 PD30 0 1.0B 10_PP2 CVXB004








Table 2 RNAC CPD120-A power cables

Equip.

No.

CABLE FROM CABLE TO

FU Conn. FU Conn. Type Use

CA_010 FTRA-B 1 1.0B PD30 0 1.0B 10_P1 CXVB18C Control

CA_011 FTRA-B 2 2.0B PD30 1 2.0B 10_P1 CXVB18C Control

CA_012 FTRA-B 3 3.0B PD30 2 3.0B 10_P1 CXVB18C ControlCA_013 FTRA-B 4 4.0B PD30 3 4.0B 10_P1 CXVB18C Control

CA_015 CAIND-A 0.0B 1 EHU 2.0B 15.4E CID030 Alarm 1)

1) The cable CA_015 from EHU is routed through the cable conduit to the front of the cabinet and con-

nected to CAIND-A.

Table 3 RNAC control cables



16 DN0638091


Id:0900d80580836290

Confidential

Intracabinet cables for the RNAC cabinet

Equip.

No.

CABLE FROM CABLE TO

Cabinet

FU Conn. Ca

binet

FU Conn. Type Use

CA_075 A OMU 0 1.0F 16.PCIe1 A WDU 0

(OMU)

1.0F 14.PCIe1 CQSFP25C PCIe

CA_076 A OMU 1 2.0F 16.PCIe1 A WDU 1

(OMU)

2.0F 13.PCIe1 CQSFP25C PCIe

CA_077 A WDU 0

(OMU)

1.0F 14.SAS A WDU 2

(OMU)

2.0F 13.SAS CMSAS011 SAS

Table 4 OMU/WDU SAS/PCIe bus cables

Equip.

No.

CABLE FROM CABLE TO


CA_040 OMU 0 1.0B 16.3F TBU 0 1.0B 19.2A CHZ006 HMS bus 0

CA_041 OMU 1 2.0B 16.3F TBU 0 2.0B 19.2A CHZ006 HMS bus 0

CA_042 TBU 0 1.0B 19.2B TBU 0 2.0B 19.2B CHZ011 HMS bus 0

CA_043 TBU 0 2.0B 19.2C TBU 0 3.0B 19.2A CHZ011 HMS bus 0

CA_044 TBU 0 3.0B 19.2B TBU 0 4.0B 19.2A CHZ012 HMS bus 0

CA_045 TBU 0 1.0B 19.2C TBU 0 1.0B 19.2D CHZ012 HMS bus 0 term. 1) 2)

CA_046 TBU 0 4.0B 19.2C TBU 0 4.0B 19.2D CHZ001 HMS bus 0 term. 2)

CA_047 OMU 0 1.0B 16.3G TBU 1 1.0B 38.5A CHZ005 HMS bus 1

CA_048 OMU 1 2.0B 16.3G TBU 1 2.0B 38.5A CHZ005 HMS bus 1

CA_049 TBU 1 1.0B 38.5B TBU 1 2.0B 38.5B CHZ009 HMS bus 1

CA_050 TBU 1 2.0B 38.5C TBU 1 3.0B 38.5A CHZ010 HMS bus 1

CA_051 TBU 1 3.0B 38.5B TBU 1 4.0B 38.5A CHZ010 HMS bus 1

CA_052 TBU 1 1.0B 38.5C TBU 1 1.0B 38.5D CHZ001 HMS bus 1 term. 1) 2)

CA_053 TBU 1 4.0B 38.5C TBU 1 4.0B 38.5D CHZ001 HMS bus 1 term. 2)

CA_054 TBU 0 1.0B 19.1Z TBU 1 2.0B 38.4Z CHZ010 HMS bus

1) If an extension cabinet (RNBC) is in use, remove the cable.

2) Do not bend the short 10 cm cables in too tight a curve.

Table 5 RNAC HMS bus cables



DN0638091 17


Id:0900d80580836290

Confidential

Equip.

No.

CABLE FROM CABLE TO


CA_063 TBU 0 1.0B 19.2M TBU 0 2.0B 19.2K CHZ011 Timing bus 0

CA_064 TBU 0 2.0B 19.2L TBU 0 3.0B 19.2K CHZ012 Timing bus 0


CA_066 TBU 0 4.0B 19.2L TBU 0 4.0B 19.2E CHZ001 Timing bus 0 term.

CA_070 TBU 1 2.0B 38.5M TBU 1 1.0B 38.5K CHZ009 Timing bus 1



CA_073 TBU 1 4.0B 38.5L TBU 1 4.0B 38.5E CHZ001 Timing bus 1 term. 1)

1) Do not bend the short 10 cm cables in too tight a curve.

Table 6 RNAC Timing bus cables

Equip.

No.

CABLE FROM CABLE TO


CA_060 NIS1P 0/

NIS1 0

3.0B 17.4V TBU 0 1.0B 19.2G CHZ028 Timing ref. 1

CA_061 NIS1P 1/

NIS1 1

4.0B 17.4V TBU 0 1.0B 19.2H CHZ028 Timing ref. 2

CA_062 NIS1P 10 3.0B 15.4V TBU 0 1.0B 19.2J CHZ028 Timing ref. 3

NIP1 0 3.0B 15.4J TBU 0 1.0B 19.2J

CA_067 NIS1P 0/

NIS1 0

3.0B 17.4X TBU 1 2.0B 38.5G CHZ028 Timing ref. 1

CA_068 NIS1P 1/

NIS1 1

4.0B 17.4X TBU 1 2.0B 38.5H CHZ028 Timing ref. 2

CA_069 NIS1P 10 3.0B 15.4X TBU 1 2.0B 38.5J CHZ028 Timing ref. 3

NIP1 0 3.0B 15.4K TBU 1 2.0B 38.5J

These cables must be installed last. They are bundled separately from other cables for easier modifica-

tion. If you want to change this cabling, it must be done at the commissioning stage. For instructions,

see Commissioning RNC, section Inspecting synchronisation system.

Table 7 RNAC default line timing cables



18 DN0638091


Id:0900d80580836290

Confidential


Figure 3 Routing of line timing cables CA_060 - CA_062 and CA_067 - CA_069



DN0638091 19


Id:0900d80580836290

Confidential

3.3 RNAC LVDS cables

3.3.1 RNAC synchronisation and LVDS cables

Equip.

No.

CABLE FROM CABLE TO


CA_156 NIS1P 0 3.0B 17.4L NIS1P 1 4.0B 17.4L CHZS011 2N_ACT

CA_157 NIS1P 2 3.0B 18.4L NIS1P 3 4.0B 18.4L CHZS011 2N_ACT

CA_161 NIS1P 10 3.0B 15.4L NIS1P 11 4.0B 15.4L CHZS011 2N_ACT 1)

CA_211 SFU 0 1.0B 2.2A SFU 1 2.0B 2.2A CIBS012 FSYNC

CA_305 TSS3 1.0B 19.1X TSS3 2.0B 38.4X CHE011 Sync

1) If NIP1 0 is configured (BIE1T or BIE1C equipped), cabling is removed.

Table 8 RNAC FSYNC and 2N_ACT cables

Equip.

No.

CABLE FROM CABLE TO


CA_200 SFU 0 1.0B 2.4J MXU 0 1.0B 9.4A CIBS006 LVDS lines

CA_202 SFU 0 1.0B 2.4V MXU 1 1.0B 11.4A CIBS008 LVDS lines

CA_204 SFU 0 1.0B 2.4G MXU 2 2.0B 9.4A CIBS012 LVDS lines

CA_206 SFU 0 1.0B 2.4T MXU 3 2.0B 11.4A CIBS012 LVDS lines

CA_208 SFU 0 1.0B 2.4E MXU 4 3.0B 9.4A CIBS016 LVDS lines

CA_210 SFU 0 1.0B 2.4R MXU 5 3.0B 11.4A CIBS016 LVDS lines

CA_264 SFU 0 1.0B 2.3Q MXU 6 4.0B 9.4A CIBS022 LVDS lines

CA_265 SFU 0 1.0B 2.3Y MXU 7 4.0B 11.4A CIBS022 LVDS lines

CA_216 SFU 1 2.0B 2.4J MXU 0 1.0B 9.4E CIBS012 LVDS lines

CA_218 SFU 1 2.0B 2.4V MXU 1 1.0B 11.4E CIBS012 LVDS lines

CA_220 SFU 1 2.0B 2.4G MXU 2 2.0B 9.4E CIBS006 LVDS lines

CA_222 SFU 1 2.0B 2.4T MXU 3 2.0B 11.4E CIBS008 LVDS lines

CA_224 SFU 1 2.0B 2.4E MXU 4 3.0B 9.4E CIBS012 LVDS lines

CA_226 SFU 1 2.0B 2.4R MXU 5 3.0B 11.4E CIBS012 LVDS lines

CA_266 SFU 1 2.0B 2.3Q MXU 6 4.0B 9.4E CIBS016 LVDS lines

CA_267 SFU 1 2.0B 2.3Y MXU 7 4.0B 11.4E CIBS017 LVDS lines

Table 9 RNAC SFU LVDS cables



20 DN0638091


Id:0900d80580836290

Confidential


CA_260 SFU 0 1.0B 2.2X NIS1P 0/

NIS1 0

3.0B 17.4C CIBS019 LVDS lines

CA_261 SFU 0 1.0B 2.3F NIS1P 1 4.0B 17.4C CIBS023 LVDS lines

Default: 2N 1)

1.0B 2.2G NIS1 1 Optional: no redundancy

1), 6)

CA_262 SFU 0 1.0B 2.2V NIS1P 2/

NIS1 2

3.0B 18.4C CIBS019 LVDS lines

CA_263 SFU 0 1.0B 2.3D NIS1P 3 4.0B 18.4C CIBS023 LVDS lines

Default: 2N 2)

1.0B 2.2E NIS1 3 Optional: no redundancy2), 7)

CA_268 SFU 0 1.0B 2.4P - 3.0B 15. 4C CIBS019 LVDS lines

Default 3), 5)

1.0B 2.2E NIS1P 10 Optional 3), 5)

CA_269 SFU 0 1.0B 2.3S - 4.0B 15. 4C CIBS023 LVDS lines

Default 4), 5)

1.0B 2.2N NIS1P 11 Optional 4), 5)

CA_270 SFU 1 2.0B 2.2X NIS1P 0/

NIS1 0

3.0B 17.4E CIBS015 LVDS lines

CA_271 SFU 1 2.0B 2.3F NIS1P 1 4.0B 17.4E CIBS019 LVDS lines

Default: 2N 1)

2.0B 2.2G NIS1 1 Optional: no redundancy

1), 6)

CA_272 SFU 1 2.0B 2.2V NIS1P 2/

NIS1 2

3.0B 18.4E CIBS015 LVDS lines

CA_273 SFU 1 2.0B 2.3D NIS1P 3 4.0B 18.4E CIBS019 LVDS lines

Default: 2N 2)

2.0B 2.2E NIS1 3 Optional: no redundancy2), (7

CA_274 SFU 1 2.0B 2.4P - 3.0B 15. 4E CIBS015 LVDS lines

Default 3), 5)

2.0B 2.2E NIS1P 10 Optional 3), 5)

CA_275 SFU 1 2.0B 2.3S - 4.0B 15. 4E CIBS019 LVDS lines

Default 4), 5)

2.0B 2.2N NIS1P 11 Optional 4), 5)

Equip.

No.

CABLE FROM CABLE TO


Table 9 RNAC SFU LVDS cables (Cont.)



DN0638091 21


Id:0900d80580836290

Confidential

1) Default cabling position: NIS1P 1 is configured as a protected unit. If NIS1 1 is configured as an unprotected

unit, the SFU end of the cabling must be changed to position x.0B 2.2G.

2) Default cabling position: NIS1P 3 is configured as a protected unit. If NIS1 3 is configured as an unprotected

unit, the SFU end of the cabling must be changed to position x.0B 2.2E.

3) If NIS1P 10 is configured in RNAC, the SFU end of the cabling must be changed to position x.0B 2.2E. If

NIS1P 10 is configured in RNBC, the default position is used.

4) If NIS1P 11 is configured in RNAC, the SFU end of the cabling must be changed to position x.0B 2.2N. If

NIS1P 11 is configured in RNBC, the default position is used.


6) NIS1 1 and NIS1P 8-9 / NIS1 8 use the same SFU ports. If NIS1 1 is equipped, NIS1P 8-9 or NIS1 8 cannot

be equipped.

7) NIS1 3 and NIS1P 10-11 / NIS1 10 use the same SFU ports. If NIS1 3 is equipped, NIS1P 10-11 or NIS1

10 cannot be equipped.

Equip.

No.

CABLE FROM CABLE TO


Table 9 RNAC SFU LVDS cables (Cont.)

Equip.

No.

CABLE FROM CABLE TO


CA_350 NIS1P 0 3.0B 17.4T NIS1P 1 4.0B 17.4T CIBS011 MSP1+1 Protection

Switch

CA_351 NIS1P 0 3.0B 17.4G NIS1P 1 4.0B 17.4G CIBS011 MSP1+1 Protection

Switch

CA_352 NIS1P 0 3.0B 17.4P NIS1P 1 4.0B 17.4P CIBS011 LVDS lines Protection

Switch

CA_353 NIS1P 0 3.0B 17.4R NIS1P 1 4.0B 17.4R CIBS011 LVDS lines Protection

Switch / FSYNC


Switch


Switch

CA_356 NIS1P 2 3.0B 18.4P NIS1P 3 4.0B 18.4P CIBS011 LVDS lines Protection

Switch

CA_357 NIS1P 2 3.0B 18.4R NIS1P 3 4.0B 18.4R CIBS005 LVDS lines Protection

Switch / FSYNC


Switch 1)


Switch 1)

CA_360 NIS1P 10 3.0B 15.4P NIS1P 11 4.0B 15.4P CIBS011 MSP1+1 Protection

Switch 1)

Table 10 RNAC NIS1P protection switch cables



22 DN0638091


Id:0900d80580836290

Confidential


3.4 LAN cables

CA_361 NIS1P 10 3.0B 15.4R NIS1P 11 4.0B 15.4R CIBS011 MSP1+1 Protection

Switch 1)


Equip.

No.

CABLE FROM CABLE TO


Table 10 RNAC NIS1P protection switch cables (Cont.)

Equip.

No.

CABLE FROM CABLE TO


CA_305 TSS3 1.0B 19.1X TSS3 2.0B 38.4X CHE011 Sync

Table 11 TSS3 synchronisation cable

Equip.

No.

CABLE FROM CABLE TO


CA_130 ESA40-A 0

/ESA24 0

1.0B 5.4C OMU 0 1.0B 16.3B CHES006 LAN

CA_131 ESA40-A 0

/ESA24 0

1.0B 5.4E OMU 1 2.0B 16.3B CHES013 LAN

CA_132 ESA40-A 0

/ESA24 0

1.0B 5.4G /OMS 1.0B 6.3B CHES006 LAN

CA_136 ESA40-A 0

/ESA24 0

1.0B 5.4P ICSU 22 1.0B 7.3B CHES006 LAN

CA_137 ESA40-A 0

/ESA24 0

1.0B 5.4R ICSU 23 2.0B 7.3B CHES015 LAN

CA_298 ESA40-A 0

/ESA24 0

1.0B 5.5Y CPSY-A 1.0B 1.1V CHE012 Ethernet

CA_138 ESA40-A 1

/ESA24 1

2.0B 5.4C OMU 0 1.0B 16.3D CHES014 LAN

CA_139 ESA40-A 1

/ESA24 1

2.0B 5.4E OMU 1 2.0B 16.3D CHES006 LAN

CA_141 ESA40-A 1

/ESA24 1

2.0B 5.4P ICSU 22 1.0B 7.3D CHES015 LAN

CA_142 ESA40-A 1

/ESA24 1

2.0B 5.4R ICSU 23 2.0B 7.3D CHES006 LAN

Table 12 ESA40-A/ESA24 0 LAN cables



DN0638091 23


Id:0900d80580836290

Confidential

3.5 RNAC alarm and synchronisation cables

CA_133 ESA40-A 1

/ESA24 1

2.0B 5.4G OMS 1.0B 6.3D CHES014 LAN

CA_134 ESA40-A 1

/ESA24 1

2.0B 5.4J ESA40-A 0

/ESA24 0

1.0B 5.4J CHES017 LAN 1)

1) The redundancy cable is not connected at the factory. The cable is only connected when the Rapid

Spanning Tree Protocol (RSTP) is enabled in the LAN sub-network. Before you connect the cable, remember

to activate the STP/RSTP/MSTP according to the planned resiliency method.

Equip.

No.

CABLE FROM CABLE TO


Table 12 ESA40-A/ESA24 0 LAN cables (Cont.)

Position ID Name FU Use

1.0B 5.1S C108585 ADMOD01 ESA40-A Cabinet address setting module

1.0B 5.1U C108585 ADMOD01 ESA40-A Subrack address setting module

2.0B 5.1S C108585 ADMOD01 ESA40-A Cabinet address setting module

2.0B 5.1U C108690 ADMOD02 ESA40-A Subrack address setting module

Table 13 ESA40-A address setting modules

Equip.

No.

CABLE FROM CABLE TO


CA_300 CPAL-A 2.0B 1.A EHU 2.0B 15.4G CJA016 Alarm

CA_301 CPAL-A 2.0B 1.G EHU 2.0B 15.4P CHQ016 Alarm

CA_302 CPAL-A 2.0B 1.P EHU 2.0B 15.4X CHM016 Alarm

CA_303 CPSY-A 1.0B 1.A TSS3 1.0B 19.1V CHE012 Sync 1)

1.0B 1.E 2)

1.0B 1.J 3)

1.0B 1.N 4)

CA_304 CPSY-B 1.10B 1.C TSS3 2.0B 38.4V CHE012 Sync 1)

1.10B 1.G 2)

1.10B 1.L 3)

1.10B 1.P 4)

CA_298 ESA40-A 0 1.0B 5.5Y CPSY-A 1.0B 1.1V CHE012 Ethernet

Table 14 RNAC alarm and synchronisation cables to rear panels CPSY-A, CPSY-B and CPAL-A



24 DN0638091


Id:0900d80580836290

Confidential


CA_299 CPSY-A 1.0B 1.1R CPSY-B 1.10B 1.1T CHE005 Sync

CA_297 CPSY-A 1.10B 1.1T CPSY-B 1.0B 1.1R CHE005 Sync

1) BNC IN, BNC OUT, default

2) BNC IN, RJ 45 OUT, optional

3) RJ 45 IN, BNC OUT, optional

4) RJ 45 IN, RJ 45 OUT, optional

Equip.

No.

CABLE FROM CABLE TO


Table 14 RNAC alarm and synchronisation cables to rear panels CPSY-A, CPSY-B and CPAL-A (Cont.)



DN0638091 25


Id:0900d80580836290

Confidential

Figure 4 CPSY-A, CPSY-B and CPAL-A panel positions in RNAC

3.6 RNAC IP upgrade cables

g If there are currently NIP/NIS interface units in the positions where the new NPGE(P)

units will be installed, remove the interface units first.

If the cabinet is equipped with a NPGE(P) 0, the following cabling is used.

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

CPSY-A

CPAL-A

CPSY-B

DN05160803



26 DN0638091


Id:0900d80580836290

Confidential




Equip.

No.

CABLE FROM CABLE TO


CA_140 NPGE(P) 0 3.0B 15.4E SWU 0 1.0B 5.4T CIBS035 LAN *

CA_150 NPGE(P) 0 3.0B 15.4G SWU 1 2.0B 5.4T CIBS035 LAN *

CA_183 NPGE(P) 0 3.0B 15.4K NPGE(P) 1 4.0B 15.4K CHZS015 PIU/PAIR

CA_186 NPGE(P) 0 3.0B 15.4L NPGE(P) 1 4.0B 15.4L CHZS015 Switchover

CA_210 BISFC for

NPGE(P) 0

3.0B 15.B00 SFU 0 1.0F 2.16 CSB018 LVDS lines

CA_230 BISFC for

NPGE(P) 0


* This connection can be used only with ESA40-A.

Table 15 NPGE(P) 0 IP upgrade cables

Equip.

No.

CABLE FROM CABLE TO


CA_141 NPGE(P) 1 4.0B 15.4E SWU 0 1.0B 5.4V CIBS035 LAN *

CA_151 NPGE(P) 1 4.0B 15.4G SWU 1 2.0B 5.4V CIBS035 LAN *



CA_211 BISFC for

NPGE(P) 1


CA_231 BISFC for

NPGE(P) 1




Equip.

No.

CABLE FROM CABLE TO


CA_156 NPGE(P) 6 3.0B 17.4E SWU 0 1.0B 5.5F CIBS035 LAN *

CA_158 NPGE(P) 6 3.0B 17.4G SWU 1 2.0B 5.5F CIBS035 LAN *



CA_212 BISFC for

NPGE(P) 6


CA_232 BISFC for

NPGE(P) 6





DN0638091 27


Id:0900d80580836290

Confidential



Equip.

No.

CABLE FROM CABLE TO


Table 17 NPGE(P) 6 IP upgrade cables (Cont.)

Equip.

No.

CABLE FROM CABLE TO


CA_157 NPGE(P) 7 4.0B 17.4E SWU 0 1.0B 5.5H CIBS035 LAN *

CA_159 NPGE(P) 7 4.0B 17.4G SWU 1 2.0B 5.5H CIBS035 LAN *



CA_213 BISFC for

NPGE(P) 7


CA_233 BISFC for

NPGE(P) 7






28 DN0638091


Id:0900d80580836292

Confidential

Intracabinet cables for the RNBC cabinet

4 Intracabinet cables for the RNBC cabinetThis chapter presents the intracabinet cabling for the RNBC cabinet in RNC450.

tThe lengths of intracabinet cables in deliveries may be different from those given in thisdocument.

4.1 RNBC power cables

4.2 RNBC control and bus cables

Equip.

No.

CABLE FROM CABLE TO

FU Conn. FU Conn. Type

CB_001 CPD120-A UB2 0.10B P1 PD30 0 1.0B 10_PP2 CVXB004








Table 19 RNBC CPD120-A power cables

Equip.

No.

CABLE FROM CABLE TO


CB_010 FTRA-B 1 1.0B PD30 0 1.0B 10_P1 CXVB18C Control




Table 20 RNBC control cables

Equip.

No.

CABLE FROM CABLE TO


CB_020 TBU 0 1.0B 19.2B TBU 0 2.0B 19.2A CHZ0011 HMS bus 0



CB_023 TBU 0 4.0B 19.2C TBU 0 4.0B 19.2D CHZ001 HMS bus 0 termination

Table 21 RNBC HMS bus cables



DN0638091 29

Cable Lists for RNC450 Intracabinet cables for the RNBC cabinet

Id:0900d80580836292

Confidential

4.3 RNBC synchronisation cables




CB_027 TBU 1 4.0B 38.5C TBU 1 4.0B 38.5D CHZ001 HMS bus 1 termination

Equip.

No.

CABLE FROM CABLE TO


Table 21 RNBC HMS bus cables (Cont.)

Equip.

No.

CABLE FROM CABLE TO


CB_030 TBU 0 1.0B 19.2L TBU 0 2.0B 19.2K CHZ011 Timing bus 0



CB_033 TBU 0 4.0B 19.2L TBU 0 4.0B 19.2E CHZ001 Timing bus 0 termi-

nation




CB_037 TBU 1 4.0B 38.5L TBU 1 4.0B 38.5E CHZ001 Timing bus 1 termi-

nation

Table 22 RNBC Timing bus cables

Equip.

No.

CABLE FROM CABLE TO


CB_048 NIS1P 4 1.0B 17.4L NIS1P 5 2.0B 17.4L CHZS011 2N_ACT




Table 23 RNBC 2N_ACT cables

Equip.

No.

CABLE FROM CABLE TO


CB_354 NIS1P 4 1.0B 17.4T NIS1P 5 2.0B 17.4T CIBS013 MSP1+1 Protec-

tion Switch

Table 24 RNBC NIS1P protection switch cables



30 DN0638091


Id:0900d80580836292

Confidential


4.4 RNBC IP upgrade cables

g If there are currently NIP/NIS interface units in the positions where the new NPGE(P)

units will be installed, remove the interface units first.


CB_355 NIS1P 4 1.0B 17.4G NIS1P 5 2.0B 17.4G CIBS013 MSP1+1 Protec-

tion Switch

CB_356 NIS1P 4 1.0B 17.4P NIS1P 5 2.0B 17.4P CIBS013 LVDS lines Pro-

tection Switch

CB_357 NIS1P 4 1.0B 17.4R NIS1P 5 2.0B 17.4R CIBS013 LVDS lines Pro-

tection Switch


tion Switch


tion Switch

CB_360 NIS1P 6 1.0B 18.4P NIS1P 7 2.0B 18.4P CIBS013 LVDS lines Pro-tection Switch


tection Switch


tion Switch


tion Switch


tection Switch


tection Switch


tion Switch


tion Switch


tection Switch


tection Switch

Equip.

No.

CABLE FROM CABLE TO


Table 24 RNBC NIS1P protection switch cables (Cont.)



DN0638091 31

Cable Lists for RNC450 Intracabinet cables for the RNBC cabinet

Id:0900d80580836292

Confidential



Equip.

No.

CABLE FROM CABLE TO


CB0_100 NPGE(P) 2 1.0B 1.4E SWU 0 1.0B 5.4X CIBS035 LAN *

CB0_108 NPGE(P) 2 1.0B 1.4G SWU 1 2.0B 5.4X CIBS035 LAN *

CB_380 NPGE(P) 2 1.0B 1.4K NPGE(P) 3 2.0B 1.4K CHZS015 PIU/PAIR

CB_390 NPGE(P) 2 1.0B 1.4L NPGE(P) 3 2.0B 1.4L CHZS015 Switchover

CB0_208 BISFC for

NPGE(P) 2


CB0_224 BISFC for

NPGE(P) 2


* This connection can be used only with ESA40-A/ESA24.


Equip.

No.

CABLE FROM CABLE TO


CB0_101 NPGE(P) 3 2.0B 1.4E SWU 0 1.0B 5.4Z CIBS035 LAN *

CB0_109 NPGE(P) 3 2.0B 1.4G SWU 1 2.0B 5.4Z CIBS035 LAN *



CB0_209 BISFC for

NPGE(P) 3


CB0_225 BISFC for

NPGE(P) 3




Equip.

No.

CABLE FROM CABLE TO


CB0_102 NPGE(P) 4 3.0B 1.4E SWU 0 1.0B 5.5B CIBS035 LAN *

CB0_110 NPGE(P) 4 3.0B 1.4G SWU 1 2.0B 5.5B CIBS035 LAN *



CB0_210 BISFC for

NPGE(P) 4


CB0_226 BISFC for

NPGE(P) 4





32 DN0638091


Id:0900d80580836292

Confidential




Equip.

No.

CABLE FROM CABLE TO


Table 27 NPGE(P) 4 IP upgrade cables (Cont.)

Equip.

No.

CABLE FROM CABLE TO


CB0_103 NPGE(P) 5 4.0B 1.4E SWU 0 1.0B 5.5D CIBS035 LAN *

CB0_111 NPGE(P) 5 4.0B 1.4G SWU 1 2.0B 5.5D CIBS035 LAN *



CB0_211 BISFC for

NPGE(P) 5


CB0_227 BISFC for

NPGE(P) 5






DN0638091 33

Cable Lists for RNC450 Intercabinet cables from RNBC to RNAC

Id:0900d80580836294

Confidential

5 Intercabinet cables from RNBC to RNACThis chapter presents cabling from the RNBC cabinet to the RNAC cabinet in RNC450.

5.1 Intercabinet LVDS cables

Equip.

No.

CABLE FROM RNBC CABLE TO RNAC


CB0_001 MXU 8 1.0B 9.4A SFU 0 1.0B 2.3O CIBS015 LVDS lines

CB0_002 MXU 9 1.0B 11.4A SFU 0 1.0B 2.3W CIBS015 LVDS lines

CB0_003 MXU 10 2.0B 9.4A SFU 0 1.0B 2.3M CIBS019 LVDS lines

CB0_004 MXU 11 2.0B 11.4A SFU 0 1.0B 2.3U CIBS019 LVDS lines

CB0_005 MXU 12 3.0B 9.4A SFU 0 1.0B 2.3B CIBS024 LVDS lines

CB0_006 MXU 13 3.0B 11.4A SFU 0 1.0B 2.3K CIBS024 LVDS lines

CB0_007 MXU 14 4.0B 9.4A SFU 0 1.0B 2.2Z CIBS029 LVDS lines

CB0_008 MXU 15 4.0B 11.4A SFU 0 1.0B 2.3H CIBS029 LVDS lines

CB0_009 MXU 8 1.0B 9.4E SFU 1 2.0B 2.3O CIBS019 LVDS lines

CB0_010 MXU 9 1.0B 11.4E SFU 1 2.0B 2.3W CIBS019 LVDS lines

CB0_011 MXU 10 2.0B 9.4E SFU 1 2.0B 2.3M CIBS015 LVDS lines

CB0_012 MXU 11 2.0B 11.4E SFU 1 2.0B 2.3U CIBS015 LVDS lines

CB0_013 MXU 12 3.0B 9.4E SFU 1 2.0B 2.3B CIBS020 LVDS lines

CB0_014 MXU 13 3.0B 11.4E SFU 1 2.0B 2.3K CIBS020 LVDS lines

CB0_015 MXU 14 4.0B 9.4E SFU 1 2.0B 2.2Z CIBS025 LVDS lines

CB0_016 MXU 15 4.0B 11.4E SFU 1 2.0B 2.3H CIBS025 LVDS lines

CB0_017 NIS1P 4/

NIS1 4

1.0B 17.4C SFU 0 1.0B 2.2L CIBS017 LVDS lines

CB0_018 NIS1P 5 2.0B 17.4C SFU 0 1.0B 2.2T CIBS021 LVDS lines

CB0_019 NIS1P 6/

NIS1 6

1.0B 18.4C SFU 0 1.0B 2.2J CIBS017 LVDS lines

CB0_020 NIS1P 7 2.0B 18.4C SFU 0 1.0B 2.2R CIBS021 LVDS lines

CB0_021 NIS1P 8/

NIS1 8

3.0B 17.4C SFU 0 1.0B 2.2G CIBS025 LVDS lines 2)

CB0_022 NIS1P 9 4.0B 17.4C SFU 0 1.0B 2.2P CIBS031 LVDS lines 2)

CB0_023 NIS1P 10/

NIS1 10

3.0B 18.4C SFU 0 1.0B 2.2E CIBS025 LVDS lines 1), 3)

CB0_024 NIS1P 11 4.0B 18.4C SFU 0 1.0B 2.2N CIBS031 LVDS lines 1), 3)

Table 29 Intercabinet LVDS cables from RNBC and RNAC



34 DN0638091


Id:0900d80580836294

Confidential

Intercabinet cables from RNBC to RNAC

Intercabinet cables CB0_001 to CB0_032 are connected and tied to the RNBC cabinet.

The ends of the cables are looped and attached to cabling shelves to be ready for con-

necting to the RNAC cabinet at the site.

CB0_025 NIS1P 4/

NIS1 4

1.0B 17.4E SFU 1 2.0B 2.2L CIBS021 LVDS lines

CB0_026 NIS1P 5 2.0B 17.4E SFU 1 2.0B 2.2T CIBS017 LVDS lines

CB0_027 NIS1P 6/

NIS1 6

1.0B 18.4E SFU 1 2.0B 2.2J CIBS021 LVDS lines

CB0_028 NIS1P 7 2.0B 18.4E SFU 1 2.0B 2.2R CIBS017 LVDS lines

CB0_029 NIS1P 8/

NIS1 8

3.0B 17.4E SFU 1 2.0B 2.2G CIBS021 LVDS lines 2)

CB0_030 NIS1P 9 4.0B 17.4E SFU 1 2.0B 2.2P CIBS027 LVDS lines 2)

CB0_031 NIS1P 10/

NIS1 10

3.0B 18.4E SFU 1 2.0B 2.2E CIBS021 LVDS lines 1), 3)

CB0_032 NIS1P 11 4.0B 18.4E SFU 1 2.0B 2.2N CIBS027 LVDS lines 1), 3)

1) If NIS1P 10 and NIS1P 11 or NIS1 10 are configured in RNAC, remove cable.

2) NIS1 1 and NIS1P 8-9 / NIS1 8 use the same SFU ports. If NIS1 1 is equipped, NIS1P 8-9 or NIS1 8

cannot be equipped.

3) NIS1 3 and NIS1P 10-11 / NIS1 10 use the same SFU ports. If NIS1 3 is equipped, NIS1P 10-11 or NIS1

10 cannot be equipped.

Equip.

No.



Table 29 Intercabinet LVDS cables from RNBC and RNAC (Cont.)



DN0638091 35


Id:0900d80580836294

Confidential

Figure 5 Routing of intercabinet LVDS cables CB0_001 - CB0_032

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

= LVDS lines / SFU 0= LVDS lines / SFU 1

DN05160881



36 DN0638091


Id:0900d80580836294

Confidential

Intercabinet cables from RNBC to RNAC

5.2 Intercabinet HMS and timing cables

Intercabinet cables CB0_040 to CB0_041 and CB0_050 to CB0_051 are connected andtied to the RNBC cabinet. The ends of the cables are looped and attached to cable-sup-

porting shelf to be ready for connecting to the RNAC cabinet at the site.

Equip.

No.



CB0_040 TBU 0 1.0B 19.2A TBU 0 1.0B 19.2C CHZ015 HMS bus 0

CB0_041 TBU 1 1.0B 38.5A TBU 1 1.0B 38.5C CHZ015 HMS bus 1

CB0_050 TBU 0 1.0B 19.2K TBU 0 1.0B 19.2N CHZ015 Timing bus 0

CB0_051 TBU 1 1.0B 38.5K TBU 1 2.0B 38.5N CHZ020 Timing bus 1

Table 30 Intercabinet HMS and timing cables from RNBC and RNAC



DN0638091 37


Id:0900d80580836294

Confidential

Figure 6 Routing of HMS cables CB0_040 - CB0_041 and timing cables CB0_050 -

CB0_051

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

38

DN05160893

= HMS bus 0 / Timing bus 0= HMS bus 1 / Timing bus 1



38 DN0638091


Id:0900d80580836296

Confidential

Physical cable equipping positions and SW port con-nection coordinates

6 Physical cable equipping positions and SW

port connection coordinates

This section shows the physical cable equipping positions in the subrack and the corre-sponding SW port connection coordinates, used in hardware configuration manage-

ment.

The cable connection coordinates are needed when creating internal port connections

between plug-in units' ports. For more information, see Creating connection descriptions

in Hardware Configuration Management .

For example, for a cable installed in position 1.0B 1.4A, the port connection coordinate

in hardware configuration management (WF commands) is B76. See also figure Nota-

tions used in table Physical cable equipping positions and corresponding SW port con-

nection coordinates.



DN0638091 39

Cable Lists for RNC450 Physical cable equipping positions and SW port con-nection coordinates

Id:0900d80580836296

Confidential

Figure 7 Notations used in table Physical cable equipping positions and corre-

sponding SW port connection coordinates

2

A

C

E

G

J

L

N

P

R

T

V

X

Z

B

D

F

H

K

M

O

Q

S

U

W

Y

3

B1

B2...

B25

B76

1

2

3

4

5

4A

...

...

B26

B51

B101

1 23

B76 4A

DN70206639

SW HW SW HW SW HW SW HW SW HW

B1 1A B26 2A B51 3A B76 4A B101 5A

B2 1B B27 2B B52 3B B77 4B B102 5B

Slot position number

Subrack seen from the rear

1

2

3

4

5

12345678910111213141516171819

1



Cable Lists for RNC450Physical cable equipping positions and SW port con-nection coordinates

SW HW SW HW SW HW SW HW SW HW

B1 1A B26 2A B51 3A B76 4A B101 5A

B2 1B B27 2B B52 3B B77 4B B102 5B

B3 1C B28 2C B53 3C B78 4C B103 5C

B4 1D B29 2D B54 3D B79 4D B104 5D

B5 1E B30 2E B55 3E B80 4E B105 5E

B6 1F B31 2F B56 3F B81 4F B106 5F

B7 1G B32 2G B57 3G B82 4G B107 5G

B8 1H B33 2H B58 3H B83 4H B108 5H

B9 1J B34 2J B59 3J B84 4J B109 5J

B10 1K B35 2K B60 3K B85 4K B110 5K

B11 1L B36 2L B61 3L B86 4L B111 5L

B12 1M B37 2M B62 3M B87 4M B112 5M

B13 1N B38 2N B63 3N B88 4N B113 5N

B14 10 B39 2O B64 3O B89 4O B114 5O

B15 1P B40 2P B65 3P B90 4P B115 5P

B16 1Q B41 2Q B66 3Q B91 4Q B116 5Q

B17 1R B42 2R B67 3R B92 4R B117 5R

B18 1S B43 2S B68 3S B93 4S B118 5S

B19 1T B44 2T B69 3T B94 4T B119 5TB20 1U B45 2U B70 3U B95 4U B120 5U

B21 1V B46 2V B71 3V B96 4V B121 5V

B22 1W B47 2W B72 3W B97 4W B122 5W

B23 1X B48 2X B73 3X B98 4X B123 5X

B24 1Y B49 2Y B74 3Y B99 4Y B124 5Y

B25 1Z B50 2Z B75 3Z B100 4Z B125 5Z

Table 31 Physical cable equipping positions and corresponding SW port connection

coordinates

Cable List Rnc450

Documents

Transcript of Cable List Rnc450