C51F4-SK

R+ R- T+ T- G 1 From PLC Code Addr 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 8 9 A B C D E F ID - - - - - - - - - - - N10 N11 N1 N43 - PT3014-C51F4-SK B2 B4 21 12 14 K25 -N10 Control Techniques PT3014-C51F4-SK User Manual Code SW Setting Pwr Rx Tx Tx Rx DB9 Female Front View DB9 Male Rear view 8 << 1 3 = 0V 4 = +24V 5 6 = TE- 7 = D- 8 = JR2 2 = D+ 1 = JR1 B7 For Motor Termistor Trip resistance: 3k, Reset resistance: 1k8 T1 (0V) The drive will not trip if the thermistor goes short circuit Commander-SK No. Function Setting 08 Motor rated voltage Check Motor Nameplate 01 02 03 04 05 07 09 10 11 17 34 Minimum set speed Maximum set speed Acceleration rate Deceleration rate Driver configuration Motor rated speed Motor power factor Parameter access Start/Stop logic select Enable negative preset speeds Terminal B7 mode select 0.0 Check Motor Nameplate 5.0 10.0 Pr. Check Motor Nameplate Check Motor Nameplate L3 3 On th 39 Motor rated frequency Check Motor Nameplate Parameter setting for Control Techniques Commander-SK 06 Motor rated current Check Motor Nameplate 40 Number of motor poles Check Motor Nameplate 42 Low frequency voltage boost 5.1 43 Serial communication baud rate 2.4 44 Serial comms address 1 H 3~ Typ FDRU 80A/ 8 0 NR.5166389 678819 B14 Y 80// 400V 2,5 A 50// 240 Hz 690// 3540 /min cosQ 0,60 0,12// 0,58 kw S 1 3KALTL.150'C IP54 ! CL -F VDE 0530 Motor Nameplate Example : Motor rated speed Motor rated frequency Motor rated current 2.5 A 240 Hz 3540 /min Example Motor Nameplate -- Parameter Setting 1 >> 8 Set all parameter to SK inverter Set the code switch position on the adapter to match the drive ID Turn off machine power install the inverter and adapter into machine and connect cable Turn on machine power observed signal lamp of adapter 1st signal lamp indicate 24V DC power from SK inverter 2nd and 3th signal lamp indicate the communication between PLC and adapter 4th and 5th signal lamp indicate the communication between adapter and SK inverter Do not issue any instruction on the machine console to load program to the inverter The adapter will not be respond the program and will generate an error message Four important parameter must be careful to set Incorrect setting will cause motor overheating or damage Motor rated voltage 400 V

Upload
adrianramon
Category

Documents
view
8
download
2

Embed Size (px):

description

Carda Rieter C51 Variador de Frecuencia

Transcript of C51F4-SK

R+R-T+T- G

From PLC

Code Addr0123456789101112131415

0123456789ABCDEF

ID-----------N10N11N1N43-

PT3014-C51F4-SK

12 14

K25

-N10

Control Techniques

PT3014-C51F4-SK User Manual

Code SW Setting

PwrRxTxTxRx

DB9 Female Front View

DB9 Male Rear view

8 << 1 3 = 0V4 = +24V56 = TE-7 = D-8 = JR2

2 = D+1 = JR1

B7For Motor Termistor

Trip resistance: 3k, Reset resistance: 1k8

T1 (0V)The drive will not trip if the thermistor goes short circuit

Commander-SK

No. Function Setting

08 Motor rated voltage Check Motor Nameplate

0102030405

0910111734

Minimum set speedMaximum set speedAcceleration rateDeceleration rateDriver configuration

Motor rated speed

Motor power factorParameter accessStart/Stop logic selectEnable negative preset speedsTerminal B7 mode select

0.0Check Motor Nameplate

5.010.0Pr.

Check Motor Nameplate

Check Motor NameplateL33Onth

39 Motor rated frequency Check Motor Nameplate

Parameter setting forControl Techniques Commander-SK

06 Motor rated current Check Motor Nameplate

40 Number of motor poles Check Motor Nameplate42 Low frequency voltage boost 5.143 Serial communication baud rate 2.444 Serial comms address 1

H 3~ Typ FDRU 80A/ 8 0NR.5166389 678819 B14Y 80// 400V2,5 A 50// 240 Hz690// 3540 /min cosQ 0,600,12// 0,58 kw S 1 3KALTL.150'CIP54 ! CL -F VDE 0530

Motor Nameplate Example :

Motor rated speedMotor rated frequencyMotor rated current 2.5 A

240 Hz3540 /min

Example Motor Nameplate -- Parameter Setting

1 >> 8Set all parameter to SK inverterSet the code switch position on the adapter to match the drive IDTurn off machine power install the inverter and adapter into machine and connect cableTurn on machine power observed signal lamp of adapter1st signal lamp indicate 24V DC power from SK inverter2nd and 3th signal lamp indicate the communication between PLC and adapter4th and 5th signal lamp indicate the communication between adapter and SK inverterDo not issue any instruction on the machine console to load program to the inverterThe adapter will not be respond the program and will generate an error message

Four important parameter must be careful to setIncorrect setting will cause motor overheating or damage

Motor rated voltage 400 V