British CFM 56
-
Upload
aionesie-dragos -
Category
Documents
-
view
641 -
download
16
Transcript of British CFM 56
B r i t i s h A i r w a y s E n g i n e e r i n g T r a i n i n g
Your Course NotesThese notes have been prepared by BritishAirways Engineering Training to provide asource of reference during your period oftraining.
The information presented is as correct aspossible at the time of printing and is notsubject to amendment action.
They will be useful to you during yourtraining, but I must emphasise that theappropriate Approved Technical Publicationsmust always be used when you are actuallyworking on the aircraft.
I trust your stay with us will be informativeand enjoyable.
JOHN QUINLISKTraining and Quality Delivery Manager
POWER PLANT (CFM56-5B)
FADEC
FADEC Presentation (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2FADEC Architecture (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4FADEC Principle (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8ECU Interfaces (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10EIU Interfaces (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12ECU Electrical PWR SPLY Control (3) . . . . . . . . . . . . . . . . . . . . . . . 16
ENGINE CONTROLS
Engine Thrust Management (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ENGINE INDICATING
Engine Warnings (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Engine Monitoring D/O (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
TABLE OF CONTENTS May 11, 2006Page 1
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
FADEC PRESENTATION (1)
GENERAL
The Full Authority Digital Engine Control (FADEC) system controls theengine. FADEC also interfaces with aircraft signals.The FADEC system of each engine consists of a dual channel ElectronicControl Unit (ECU), with its associated peripherals.The ECU is the computer of the FADEC system and is located on theengine fan case.
FADEC FUNCTIONS
The FADEC provides the regulation and scheduling of the engine systemsto control the thrust and optimize engine operation.The FADEC system performs engine control functions and engine/A/Cintegration.The Engine control functions include:- Power management control,- Variable Bleed Valves (VBVs) control,- Variable Stator Vanes (VSVs) control,- Transient Bleed Valve (TBV) control,- Fuel control regulation,- High Pressure Turbine Active Clearance Control (HPTACC),- Low Pressure Turbine Active Clearance Control (LPTACC),- Fuel Return Valve (FRV) control.Engine/A/C integration includes:- Engine indication,- Engine maintenance data,- Automatic and manual starting,- Thrust reverser control,- Autothrust,- Condition monitoring data.
POWER SUPPLY
Each ECU is powered by a three-phase permanent magnet alternatorwhen the engine N2 > 15%. The FADEC Control Alternator provides anindependent power supply to both ECU channels.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
FADEC PRESENTATION (1) May 10, 2006Page 2
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
P1C
FM00
0001
GENERAL ... POWER SUPPLY
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
FADEC PRESENTATION (1) May 10, 2006Page 3
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
P1C
FM00
0001
FADEC ARCHITECTURE (1)
DUAL CHANNEL
The Full Authority Digital Engine Control (FADEC) system is fullyredundant and built around two independent Electronic Control Unit(ECU) control channels.Dual inputs, dual outputs, and automatic switch over from one channelto the other, eliminates any dormant failure.The ECU consists of two channels (A and B). Each channel can controlthe different components of the engine systems.Channels A and B are permanently operational. The channel in controlmanages the systems.
DUAL INPUTS
All control inputs to the FADEC system are dual. Only some secondaryparameters used for monitoring and indicating are single.To increase the fault tolerant design, the parameters are exchangedbetween the two control channels (inside the ECU) via the cross channeldata link. Each channel can also operate independently, without crosschannel data link.
HARDWIRED INPUTS
Most of the communication between the A/C systems and the ECU istransmitted over digital data buses.In addition, some signals are hardwired directly from the A/C to the ECU.
DUAL OUTPUTS
All of the ECU control outputs are dual. The channel that is in controlsupplies the control signals to the various components such as torquemotors and solenoids.The other channel calculation is used for crosschecking.
BITE CAPABILITY
The ECU is equipped with a Built-in Test Equipment (BITE) systemwhich provides maintenance information and test capabilities via theMCDU.
FAULT STRATEGY
The ECU can detect and isolate failures using the BITE system.The BITE system allows the ECU to switch engine control functionsfrom a faulty channel to the healthy one.
FAIL SAFE CONTROL
If one channel is faulty, and the channel that is in control cannot ensurean engine component function, the component is moved to a fail-safeposition.Example: if one channel is faulty and the other channel is unable to controlthe Variable Bleed Valve (VBV) position, the VBVs are set to the fail-safeopen position.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
FADEC ARCHITECTURE (1) May 10, 2006Page 4
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
P2C
FM00
0001
DUAL CHANNEL ... FAIL SAFE CONTROL
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
FADEC ARCHITECTURE (1) May 10, 2006Page 5
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
P2C
FM00
0001
FADEC ARCHITECTURE (1)
MAIN INTERFACES
The ECU performs its tasks by interfacing with A/C system computers,either directly, or via the Engine Interface Unit (EIU). The EIU is aninterface concentrator that serves as the communication link, betweenthe A/C systems and the FADEC system. There is one EIU for eachengine.The ECU receives inputs from:- Air Data Inertial Reference Units (ADIRUs),- Flight Control Unit (FCU),- Environmental Control System (ECS) computers,- Centralized Fault Display Interface Unit (CFDIU),- Landing Gear Control and Interface Units (LGCIUs),- cockpit engine controls including fire, anti-ice systems and ThrottleLever Angle (TLA).The ECU sends outputs to:- Flight Data Interface and Management Unit (FDIMU),- Flight Warning Computers (FWCs),- Display Management Computers (DMCs),- Flight Management and Guidance Computers (FMGCs),- Centralized Fault Display Interface Unit (CFDIU),- Bleed air Monitoring Computers (BMCs) through the EIU.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
FADEC ARCHITECTURE (1) May 10, 2006Page 6
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
P2C
FM00
0001
MAIN INTERFACES
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
FADEC ARCHITECTURE (1) May 10, 2006Page 7
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
P2C
FM00
0001
FADEC PRINCIPLE (2)
GENERAL
The Full Authority Digital Engine Control (FADEC) system managesthe engine thrust and optimizes the performance.
FADEC
The FADEC consists of the Electronic Control Unit (ECU) and itsperipheral components and sensors used for control and monitoring.The ECU interfaces with the other A/C systems through the EngineInterface Unit (EIU).The primary parameters (N1, N2, Exhaust Gas Temperature (EGT) andFuel Flow (FF)) are directly sent by the ECU to the ECAM. The secondaryparameters are sent to the ECAM trough the EIU.
ENGINE INTERFACE UNIT
Each EIU, located in the avionics bay, is an interface concentrator betweenthe airframe and the corresponding ECU located on the engine.There is one EIU for each engine. It interfaces with the correspondingECU.
POWER MANAGEMENT
The FADEC provides automatic engine thrust control and thrust parameterlimit computation.The FADEC manages power according to two thrust modes:- manual mode depending on Throttle Lever Angle (TLA),- autothrust mode depending on autothrust function generated by theAuto Flight System (AFS).The FADEC also provides two idle mode selections: minimum idle andapproach idle, obtained when the slats are extended. The idle can also bemodulated up to approach idle depending on: air conditioning demand,wing anti-ice demand, engine anti-ice demand and oil temperature (forIntegrated Drive Generator (IDG) cooling).
ENGINE LIMIT PROTECTION
The FADEC provides overspeed protection for N1 and N2, in order toprevent the engine from exceeding certified limits and also monitors theEGT.
ENGINE SYSTEM CONTROL
The FADEC provides optimal engine operation by controlling:- FF,- Turbine Clearance and Compressor Airflow.
STARTING AND IGNITION CONTROL
The FADEC controls the engine start sequence.It monitors N1, N2, and EGT parameters and can abort or recycle anengine start.The FADEC controls the starting and ignition in automatic mode wheninitiated from the ENG start panel (115 VU) or manual mode wheninitiated from the ENG MAN START panel.
THRUST REVERSER
The FADEC entirely supervises the thrust reverser operation.In case of malfunction, the thrust reverser is stowed.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
FADEC PRINCIPLE (2) May 10, 2006Page 8
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
P3C
FM00
0001
GENERAL ... THRUST REVERSER
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
FADEC PRINCIPLE (2) May 10, 2006Page 9
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
P3C
FM00
0001
ECU INTERFACES (3)
GENERAL
The Electronic Control Unit (ECU) interfaces with various systemsthrough channels A and B.
ECU CHANNEL A INPUTS
Channel A receives via bus network:- The anemometric parameters for thrust calculation from the Air DataInertial Reference System (ADIRS),- The A/C command signals from the Engine Interface Unit (EIU) forengine control.Each ECU receives a single hardwired signal from the instinctivedisconnect push buttons. The Throttle Control Unit sends the ThrottleResolver Angle (TRA). Each ECU also receives signals from enginesensorsNOTE: The relationship between the Throttle Lever Angle (TLA) andTRA is linear and: 1 degree TLA is 1.9 degrees TRA.The ECU is electrically supplied via the EIU only when N2 is below12%. The ignition is supplied by 115 VAC.
ECU CHANNEL B INPUTS
Channel B has the same inputs as channel A from the ADIRS, EIU,Throttle Control Unit, autothrust disconnect switches and engine sensors.
ECU CHANNEL A OUTPUTS
Channel A provides outputs via ARINC buses to the: EIU, Flight DataInterface and Management Unit (FDIMU) - DMU part, Flight WarningComputers (FWCs), Display Management Computers (DMCs), FlightManagement and Guidance Computers (FMGCs).Channel A also provides outputs to the engine controls (torque motorsand solenoids).
ECU CHANNEL B OUTPUTS
Channel B provides outputs via ARINC buses to the: EIU, FWCs, DMCs,and FMGC. It also provides outputs to the engine controls.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ECU INTERFACES (3) May 10, 2006Page 10
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
D3C
FM00
0001
GENERAL ... ECU CHANNEL B OUTPUTS
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ECU INTERFACES (3) May 10, 2006Page 11
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
D3C
FM00
0001
EIU INTERFACES (3)
INPUTS
The Engine Interface Unit (EIU) receives digital, discrete and analoginputs.
DIGITAL INPUTSThe Engine Interface Unit (EIU) receives digital inputs from:- the Centralized Fault Display Interface Unit (CFDIU) for enginetroubleshooting and test,- the Air Conditioning System Controller (ACSC), for bleed airdemands of the air conditioning system,- and the Flight Control Unit (FCU) for the auto-thrust function.The EIU also receives data from each channel of the Electronic ControlUnit (ECU).
DISCRETE INPUTSThe EIU receives command signals from the following control panels:- wing anti-ice,- engine anti-ice,- Full Authority Digital Engine Control (FADEC) ground power panel,- engine fire panel,- engine start panel,- Throttle Control Unit thrust reverser microswitch.It also receives specific signals of A/C configuration from thefollowing computers:- Landing Gear Control Interface Unit (LGCIU),- Slat and Flap Control Computer (SFCC),- Fuel Level Sensing Control Unit (FLSCU).
OTHER DISCRETE INPUTSOther discrete inputs are provided for the engine oil low pressurewarning.
ANALOG INPUTSThe EIU receives analog signals corresponding to values of secondaryparameters from engine sensors, for display on the ECAM enginepage.
OUTPUTS
The EIU sends digital and discrete outputs.
DIGITAL OUTPUTSThe EIU sends digital outputs to:- the Bleed Monitoring Computer (BMC) for pneumatic valveoperation,- the Flight Warning Computers (FWC) for alarms and indication,- and, the Centralized Fault Display Interface Unit, (CFDIU) for faultmessages.Other digital outputs are sent to channel A and channel B of the ECU.
DISCRETE OUTPUTSThe EIU provides the following discrete outputs to other A/C systemsfor some required commands and specific engine operations:- start valve closure,- thrust reverser inhibition,- APU boost demand,- oil low pressure,- HP fuel Shut-off Valve (SOV) closed,- N2 at or above minimum idle,- Throttle Lever Angle (TLA) in takeoff position,- engine FAULT light on.
SUPPLY MODULE
The EIU contains a power supply module that is used to supply electricalpower to the ECU and the ignition systems.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
EIU INTERFACES (3) May 10, 2006Page 12
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
D4C
FM00
0001
NOTE: If the EIU electrical power is lost, the EIU fails and enginerestart is not possible.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
EIU INTERFACES (3) May 10, 2006Page 13
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
D4C
FM00
0001
INPUTS ... SUPPLY MODULE
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
EIU INTERFACES (3) May 10, 2006Page 14
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
D4C
FM00
0001
This Page Intentionally Left Blank
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
EIU INTERFACES (3) May 10, 2006Page 15
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
D4C
FM00
0001
ECU ELECTRICAL PWR SPLY CONTROL (3)
GENERAL
The Electronic Control Unit (ECU) is supplied from the aircraft electricalpower when the engine is shut down or when N2<15%. The PermanentMagnet Alternator (PMA) supplies the ECU when the engine is runningand N2>15%.
POWERING N2<15%
Each channel is independently supplied by the aircraft 28 VDC throughthe Engine Interface Unit (EIU). At initial A/C power-up, both engineECUs are supplied with aircraft power for 5 minutes.Aircraft 28 VDC is used for:- power-up check of the Full Authority Digital Engine Control (FADEC)before engine start,- engine starting,- powering the ECU while the engine is running below 15% N2.Note that the EIU takes its power from the same bus bar as ECU.
POWERING N2>15%
As soon as engine is running above 15% of N2, the PMA is able todirectly supply the ECU.The PMA supplies each channel with three-phase AC power. Twotransformer rectifiers provide 28 VDC power supply to channels A andB.Above 15% of N2, the ECU logic automatically switches to PMA supply.The supply from the aircraft network is cut off through the EIUde-powering function.Note that in case of PMA failure, the ECU will automatically receive, asback-up, the 28 VDC power from the aircraft network through the EIU.
AUTO DE-POWERING
The FADEC is automatically de-powered on the ground, through theEIU, after engine shutdown.ECU automatic de-powering on the ground:- five minutes after aircraft power up,- five minutes after engine shut down.Note that releasing the ENGine FIRE P/B out provides ECU power cutoff from the aircraft network.
FADEC GROUND POWER PANEL
For maintenance purposes and MCDU engine tests, the ENGine FADECGrouND PoWeR P/B on the MAINTenance panel (50VU) permitsFADEC power supply to be restored on the ground with engine shutdown.When the corresponding ENGine FADEC GrouND PoWeR P/B is pressedON the ECU receives its power supply again. The ECU will bede-powered after 5 minutes of the engine shutdown to allow the engineparameters monitoring.Also note that the FADEC is repowered as soon as the engine start selectoris selected to CRANK or IGNition START or the MASTER switch isselected ON.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ECU ELECTRICAL PWR SPLY CONTROL (3) May 10, 2006Page 16
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
D5C
FM00
0001
GENERAL ... FADEC GROUND POWER PANEL
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ECU ELECTRICAL PWR SPLY CONTROL (3) May 10, 2006Page 17
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M73
D5C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
BASIC INFORMATION
Some basic information about Engine Thrust Management is shown inthis module.
PREDICTED N1The predicted N1 is indicated by a white circle in case of classicECAM version and by a blue circle in case of enhanced ECAMversion, on the N1 indicator and corresponds to the value determinedby the Throttle Lever Angle (TLA).
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 18
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
BASIC INFORMATION - PREDICTED N1
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 19
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
BASIC INFORMATION (continued)
THRUST LIMIT MODEThe throttle levers are used as thrust limit mode selectors. Dependingon the throttle lever position, a thrust limit mode is selected andappears on the upper ECAM display.If the throttle levers are set between two detent points, the upper detentwill determine the thrust limit mode.The thrust limit modes are: Climb (CL), Flexible Take Off orMaximum Continuous Thrust (FLX/MCT), or Take Off Go Around(TOGA).
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 20
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
BASIC INFORMATION - THRUST LIMIT MODE
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 21
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
BASIC INFORMATION (continued)
N1 LIMITFor each thrust limit mode selection, an N1 limit is computedaccording to the Air Data Reference (ADR) and appears on the upperECAM display near the thrust limit mode indication.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 22
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
BASIC INFORMATION - N1 LIMIT
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 23
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
BASIC INFORMATION (continued)
N1 TARGETIn Autothrust (A/THR) function, the Flight Management and GuidanceSystem (FMGC) computes an N1 target according to air data andengine parameters and sends it to the Electronic Control Unit (ECU).
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 24
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
BASIC INFORMATION - N1 TARGET
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 25
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
BASIC INFORMATION (continued)
N1 COMMANDThe N1 command, used to regulate the fuel flow, is the FMGC N1target when the A/THR function is active.When the A/THR function is not active, the N1 command is the N1corresponding to the TLA.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 26
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
BASIC INFORMATION - N1 COMMAND
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 27
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
BASIC INFORMATION (continued)
ACTUAL N1The actual N1 is the actual value given by the N1 speed sensor.This actual N1 is displayed in green on the N1 indicator and this actualN1 signal is also compared to the N1 command.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 28
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
BASIC INFORMATION - ACTUAL N1
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 29
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
AUTOTHRUST CONTROL MODE
The A/THR function is engaged manually when the A/THR P/B isselected or automatically at take off power application.
AUTOTHURST ACTIVEWhen engaged, the A/THR function becomes active when the throttlelevers are set to CLimb detent after take off. The N1 command is theFMGC N1 target.A/THR function is normally active when the throttle levers are setbetween IDLE and CLimb (including CLimb).The A/THR active range is extended to MCT in the case of singleengine operation.When the throttle levers are set between two detent points, the N1command is limited by the throttle lever position.Note: In Alpha Floor condition the A/THR function becomes activeautomatically. The N1 target is TOGA.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 30
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
AUTOTHRUST CONTROL MODE - AUTOTHURST ACTIVE
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 31
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
AUTOTHRUST CONTROL MODE (continued)
AUTOTHRUST NOT ACTIVEWhen engaged, the A/THR function becomes inactive when thethrottle levers are set above CLimb with 2 engines running.The N1 command corresponds to the TLA. A/THR function is notactive above MCT in case of single engine operation.The A/THR function is disengaged when the throttle levers are set atIDLE stop.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 32
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
AUTOTHRUST CONTROL MODE - AUTOTHRUST NOT ACTIVE
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 33
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE THRUST MANAGEMENT (3)
MANUAL CONTROL MODE
Manual mode when A/THR not engaged.The ECU processes the N1 command signal according to the TLA.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 34
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
MANUAL CONTROL MODE
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE THRUST MANAGEMENT (3) May 10, 2006Page 35
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M76
D1C
FM00
0001
ENGINE WARNINGS (3)
LOW N1
In case of low N1 warning, the MASTER CAUTion comes on and theaural warning sounds.The failure is shown amber on the upper ECAM display, and the lowerECAM SD ENGINE page appears.This warning appears when there is a low N1 rotation speed during enginestart.This warning is inhibited in flight phases 4, 5, 6, 7, 8, 9, and 10.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 36
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
LOW N1
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 37
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
ENGINE WARNINGS (3)
EGT, N1 OR N2 OVERLIMIT
In case of Exhaust Gas Temperature (EGT), N1 or N2 over limit warning,the MASTER CAUTion comes on and the aural warning sounds.The EGT indication is shown red and the failure message appears amberon the upper ECAM display.This warning appears when EGT exceeds 950 degrees Celsius.The over limit for N1 is 104% and the corresponding message is 'ENG1 (2) N1 OVER LIMIT".The over limit for N2 is 105% and the corresponding message is 'ENG1 (2) N2 OVER LIMIT".This warning is inhibited in flight phases 4, and 8.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 38
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
EGT, N1 OR N2 OVERLIMIT
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 39
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
ENGINE WARNINGS (3)
THROTTLE LEVER DISAGREE
In case of throttle lever disagreement warning, the MASTER CAUTioncomes on and the aural warning sounds.The failure is shown amber on the upper ECAM display, and the lowerECAM SD ENGINE page appears.This warning appears when there is a disagreement between both resolversof a throttle lever.This warning is inhibited in flight phases 4, 5, and 8.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 40
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
THROTTLE LEVER DISAGREE
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 41
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
ENGINE WARNINGS (3)
THROTTLE LEVER FAULT
In case of throttle lever fault warning, the MASTER CAUTion comeson and the aural warning sounds.The failure is shown amber on the upper ECAM display.This warning appears when both resolvers on one throttle lever are lost.This warning is inhibited in flight phases 4, 5, and 8.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 42
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
THROTTLE LEVER FAULT
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 43
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
ENGINE WARNINGS (3)
OIL LOW PRESSURE
In case of oil low pressure warning, the MASTER WARNing flashesand the aural warning sounds.The failure is shown red on the upper ECAM display, and the lowerECAM SD ENGINE page appears.This warning appears when the oil pressure is lower than 13 PSI.This warning is inhibited in flight phases 1 and 10.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 44
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
OIL LOW PRESSURE
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 45
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
ENGINE WARNINGS (3)
OIL HIGH TEMPERATURE
In case of oil high temperature warning, the MASTER CAUTion comeson and the aural warning sounds.The failure is shown amber on the upper ECAM display, and the lowerECAM SD ENGINE page appears.This warning appears when the engine oil temperature is between 140degrees Celsius and 155 degrees Celsius for more than 15 minutes, or ifthe oil temperature is greater than 155 degrees Celsius.This warning is inhibited in flight phases 4, 5, 7, and 8.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 46
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
OIL HIGH TEMPERATURE
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 47
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
ENGINE WARNINGS (3)
OIL FILTER CLOG
In case of oil filter clog warning, the failure is shown amber on the ECAMdisplays.This warning appears when the pressure loss across the main supply oilfilter is excessive (differential pressure greater than 25.5 PSI).This warning is inhibited in flight phases 4, 5, 7, and 8.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 48
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
OIL FILTER CLOG
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 49
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
ENGINE WARNINGS (3)
FUEL FILTER CLOG
In case of fuel filter clog warning, the failure is shown amber on theECAM displays.This warning appears when the pressure loss across the fuel filter isexcessive (differential pressure greater than 11.5 PSI).This warning is inhibited in flight phases 4, 5, 7, and 8.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 50
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
FUEL FILTER CLOG
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 51
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
FUEL FILTER CLOG
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 52
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
This Page Intentionally Left Blank
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE WARNINGS (3) May 10, 2006Page 53
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D1C
FM00
0001
ENGINE MONITORING D/O (3)
INTRODUCTION
The engine monitoring is carried out by means of the Electronic ControlUnit (ECU) and the vibration monitoring system with a display on theECAM.The ECU receives engine inlet condition data from the Air Data/InertialReference System (ADIRS), operational commands from the EngineInterface Unit (EIU), and monitoring parameters from the variousdedicated engine sensors.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 54
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
INTRODUCTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 55
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
PRIMARY PARAMETERS
The engine primary monitoring parameters displayed on the ECAM EWDare:- Low Pressure (LP) rotor speed indication (N1),- Exhaust Gas Temperature (EGT) indication,- High Pressure (HP) rotor speed indication (N2),- Fuel Flow (FF) indication,- thrust limit mode,- N1 rating limit.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 56
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
PRIMARY PARAMETERS
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 57
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
PRIMARY PARAMETERS (continued)
ROTATIONAL SPEED PARAMETERS DESCRIPTIONThe N1 speed sensor is installed in the fan frame strut No.6 at the5:00 o'clock position. It senses the LP rotor assembly rotational speedand transmits the corresponding signals to the Engine VibrationMonitoring Unit (EVMU) and the ECU. The N1 rotational speedindication is shown in the ECAM EWD by a needle and a N1 digitalindication display.The N2 speed sensor is installed at 6:30 o'clock on the AccessoryGearbox (AGB) rear face. The N2 speed sensor detects the rotationalspeed of the HP rotor assembly and transmits the signal to the EVMUand the ECU. The N2 rotational speed is indicated in the ECAM EWD.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 58
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
PRIMARY PARAMETERS - ROTATIONAL SPEED PARAMETERS DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 59
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
PRIMARY PARAMETERS (continued)
LPT SECTION PARAMETERS DESCRIPTIONThe engine EGT is sensed and averaged by 9 thermocouple probeslocated in the T49.5 plane of Low Pressure Turbine (LPT) stage-2nozzle assembly. The actual engine EGT is displayed in the ECAMEWD by a needle and an EGT digital indication.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 60
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
PRIMARY PARAMETERS - LPT SECTION PARAMETERS DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 61
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
PRIMARY PARAMETERS (continued)
FUEL FLOW PARAMETER DESCRIPTIONThe FF transmitter (XMTR) is mounted at 4 o'clock on the enginenext to the AGB and does not require an electrical power input. Themaximum flow across this XMTR is 6360 kg/hr (14000 lb/hr). TheFF is shown in the ECAM EWD by a FF digital indication.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 62
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
PRIMARY PARAMETERS - FUEL FLOW PARAMETER DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 63
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
SECONDARY PARAMETERS
The engine secondary monitoring parameters are displayed on the ECAMlower SD when it is selected manually or automatically.The engine secondary parameters that appear permanently in the ECAMENGINE page are:- fuel used indication,- oil quantity indication,- oil pressure indication,- oil temperature indication,- ignition indication,- start valve position indication,- engine bleed pressure,- vibration indication.The engine secondary parameters non permanently displayed on the SDare:- oil filter clog indication,- fuel filter clog indication,- nacelle temperature indication.On the enhanced system, the same information is provided with a differentdisplay presentation.Fuel used, oil quantity and vibration indications are also displayed onthe ECAM CRUISE page.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 64
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
SECONDARY PARAMETERS
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 65
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
SECONDARY PARAMETERS
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 66
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
SECONDARY PARAMETERS
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 67
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
SECONDARY PARAMETERS (continued)
OIL PARAMETERS DESCRIPTIONThe oil quantity XMTR is located in the oil tank. It is displayed onECAM SD.The oil pressure XMTR is located on the lubrication unit outlet line.It is displayed on ECAM SD.An oil temperature sensor for the Engine Condition Monitoring (signalto EIU) is located on the main oil pressure filter housing of thelubrication unit, downstream of the pressure pump oil system. It isdisplayed on the ECAM SD.An oil differential pressure switch (also named oil clogging switch)is installed on the lubrication unit. The pressure switch signal is usedby the ECAM system to generate the main oil filter clog indicationwhen the oil differential pressure across this filter is comprisedbetween 29 psig (2 bar) and 33 psig (2.28 bar).An engine oil temperature sensor for the Integrated Drive Generator(IDG) cooling system control (signal to ECU) is located above the oiltank.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 68
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
SECONDARY PARAMETERS - OIL PARAMETERS DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 69
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
SECONDARY PARAMETERS - OIL PARAMETERS DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 70
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
This Page Intentionally Left Blank
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 71
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
SECONDARY PARAMETERS (continued)
VIBRATION PARAMETERS DESCRIPTIONThe No. 1 bearing sensor is formed by an accelerometer located at9:00 o'clock position on No. 1 and No .2 bearing support and a sensorcable that is routed through the fan frame. The No. 1 bearing vibrationsensor permanently monitors the vibrations from No. 1 bearing andthe vibrations from LPT and High Pressure Turbine (HPT) shafts. It'salso used to the fan trim balance procedure.The Turbine Rear Frame (TRF) vibration sensor is installed at 12o'clock on the front flange of the TRF. The TRF vibration sensor isused as back-up of N1 bearing accelerometer to monitor and, ifnecessary, reduce the engine vibration level using the trim balanceprocedure.The aircraft EVMU uses the vibration and the rotational speed signalsto extract all the vibration signals and compute the position and theamplitude of the unbalanced signals.As normal vibration is depending on rotor speed, for each speed, theEVMU processes the ratio actual value/maxi value. This ratio ismultiplied by 10 and is available on the EVMU output for display onECAM SD.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 72
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
SECONDARY PARAMETERS - VIBRATION PARAMETERS DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 73
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
SECONDARY PARAMETERS (continued)
FUEL PARAMETERS DESCRIPTIONThe fuel used value computed by the Full Authority Digital EngineControl (FADEC) is displayed in green on the ECAM SD.A CLOG message appears in amber, associated with an ECAMmessage only when the differential pressure across the fuel filter isexcessive.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 74
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
SECONDARY PARAMETERS - FUEL PARAMETERS DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 75
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
SECONDARY PARAMETERS (continued)
NACELLE TEMPERATURE INDICATIONThe nacelle temperature is monitored by a temperature probe installedin the ventilated core compartment.The nacelle temperature sensor can provide indication to the ECAMSD.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 76
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
SECONDARY PARAMETERS - NACELLE TEMPERATURE INDICATION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 77
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
OPTIONAL PARAMETERS
The T5 sensor is an optional monitoring sensor that meters the turbineexhaust temperature.The P25 optional sensor measures the air pressure downstream of thebooster or the High Pressure Compressor (HPC) inlet.PS13 is an optional sensor.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 78
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
OPTIONAL PARAMETERS
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 79
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
COMBUSTION AND HPT SECTION PARAMETERSDESCRIPTION
Tcase sensor is located between the combustion chambers and the HPT.The T3 sensor measures the compressor discharge temperature.The PS3 sensor meters the compressor discharge pressure.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 80
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
COMBUSTION AND HPT SECTION PARAMETERS DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 81
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
ENGINE MONITORING D/O (3)
COMPRESSOR SECTION PARAMETERS DESCRIPTION
The T12 sensor is made to measure the engine intake air temperature. Itis installed on the engine fan inlet case at the 1:00 o'clock position.The PS12 sensor measures the static pressure from the fan inlet.The T25 sensor is located at 4:30 o'clock upstream of Variable BleedValve (VBV) in the fan frame. The sensor measures the air temperaturedownstream of the booster or HPC inlet.
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 82
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
COMPRESSOR SECTION PARAMETERS DESCRIPTION
MAINTENANCE COURSE - T2 (CFM56-5B/ME) 70 - POWER PLANT (CFM56-5B)
ENGINE MONITORING D/O (3) May 10, 2006Page 83
SINGLE AISLE TECHNICAL TRAINING MANUALU
3T06
191
- U
13T
2M0
- U
M77
D2C
FM00
0001
AIRBUS S.A.S.31707 BLAGNAC cedex, FRANCE
STMREFERENCE U3T06191
MAY 2006PRINTED IN FRANCEAIRBUS S.A.S. 2006
ALL RIGHTS RESERVED
AN EADS JOINT COMPANYWITH BAE SYSTEMS