Board 2 bcon draft
1
SABD | Building Construction II | BLD 60703 | Project 2 Understanding Forces in Building Construction | Mr Edwin | Cherilyn Chia 0321986 | Lim Woo Leon 0322180 | Shreya Maria Wilson 0322173 CONSTRUCTION DETAILS ASU SKYSONG Cleats Welded onto the top of the A-frame columns to allow attachment of cables. SPIGOT connection Used for the connection of 2 circular steel tubes to achieve the desired length, which is 111 feet. PIN JOINT Attach column (masts) to base plate through welding. Telescopic strut connection Steel plate is welded and connected to a steel structure with a smaller diameter. welded JOINT with cleats PIN JOINT Bale ring MEMBRANE PLATE elevATION SCALE 1: 500 BALE RING PTFE membrane is clamped onto the bale ring to form conical shaped structures. It is found on the top and bottom of the A-frame columns alternatively to achieve its form. Tensioning Angle Fabric Clamp Plate Clamp Plate all thread Rod All thread Rod, bolts and nuts Angle Receiving Plate with Spacer Plates to allow for overflow Scupper Plate assembly PTFE membrane Catenary Cable membrane plate Clamps onto the fabric’s corner to pull the fabric tightly, holds the ends of the catenary cables that run in the fabric edge pockets. ktop CABLE ANCHORING Steel cables are anchored to the steel cleats which are welded onto the base plate. The base plate is then secured onto the concrete foundation with bolts and nuts. Steel cable Hinge joint Base plate Bolted joint Welded joint Steel plate Circular Hollow Column Galvanized steel structure Conical steel structure Pin Joint Base plate Membrane plate Bolted connection to the steel cable Tension cables to hold the A-frame column CONCRETE POSTS PLAn SCALE 1: 1500 References: ASU SkySong Innovation Center - Scottsdale, AZ. (2017, March 23). Retrieved June 16, 2017, from https://www.fabritecstructures.com/engineering-tensioned-fabric-structures-ASU-Skysong BANANA TRUSSES tension cable anchor point TOP RING bottom RING MEMBRANE PLATE welded JOINT with cleats CATENARY edge CLAMP Clamps fabric to catenary cables running next to the banana trusses. Secured by bolts and nuts Clamped PTFE membrane Catenary cables
Transcript of Board 2 bcon draft
SABD | Building Construction II | BLD 60703 | Project 2 Understanding Forces in Building Construction | Mr Edwin | Cherilyn Chia 0321986 | Lim Woo Leon 0322180 | Shreya Maria Wilson 0322173
CONSTRUCTION DETAILSASU SKYSONG
Cleats
Welded onto the top of the A-frame columns to allow attachment of cables.
SPIGOT connection
Used for the connection of 2 circular steel tubes to achieve the desired length, which is 111 feet.
PIN JOINT
Attach column (masts) to base plate through welding.
Telescopic strut connection
Steel plate is welded and connected to a steel structure with a smaller diameter.
welded JOINT with cleats
PIN JOINT
Bale ring
MEMBRANE PLATE
elevATION SCALE 1: 500
BALE RING
PTFE membrane is clamped onto the bale ring to form conical shaped structures. It is found on the top and bottom of the A-frame columns alternatively to achieve its form.
Tensioning Angle
Fabric Clamp Plate
Clamp Plate all thread Rod
All thread Rod, bolts and nuts
Angle Receiving Plate with Spacer Plates to allow for overflow
Scupper Plate assembly
PTFE membrane
Catenary Cable
membrane plate
Clamps onto the fabric’s corner to pull the fabric tightly, holds the ends of the catenary cables that run in the fabric edge pockets.
C:\U
sers
\Shr
eya\
Desk
top\
edits
\ASU
002_
0.pn
g
CABLE ANCHORINGSteel cables are anchored to the steel cleats which are welded onto the base plate. The base plate is then secured onto the concrete foundation with bolts and nuts.
Steel cable
Hinge joint
Base plate
Bolted joint
Welded joint
Steel plate
Circular Hollow Column
Galvanized steel structure
Conical steel structure
Pin Joint
Base plate
Membrane plate
Bolted connection to the steel cable
Tension cables to hold the A-frame column
CONCRETE POSTS
PLAn SCALE 1: 1500
References: ASU SkySong Innovation Center - Scottsdale, AZ. (2017, March 23). Retrieved June 16, 2017, from https://www.fabritecstructures.com/engineering-tensioned-fabric-structures-ASU-Skysong
BANANA TRUSSES
tension cable anchor point
TOP RING
bottom RING MEMBRANE PLATE
welded JOINT with cleats
CATENARY edge CLAMP
Clamps fabric to catenary cables running next to the banana trusses.
Secured by bolts and nuts
Clamped PTFE membrane
Catenary cables
