Blue - Scene7
2
Installation Without a Stake Light Kit www.HunterFan.com 1.888.830.1326 Using a Phillips Head screwdriver, install the switch housing cap to the lower switch housing using the two switch housing cap screws. Switch Housing Cap Screw Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Switch Housing Assembly Screw Attach the pull chain pendant to the short chain coming from the lower switch housing. M0030-01 • 08/24/12 • © Hunter Fan Company Locate the two light kit screws that attach the light kit to the lower switch housing. Light Kit Screw Using a Phillips head screwdriver, remove the two light kit screws from the light kit which will allow it to be separated from the lower switch housing. Light Kit Screw Disconnect the blue wire in the light kit from the blue wire in the lower switch housing. Disconnect the white wire in the light kit from the white wire in the lower switch housing. Install a dummy terminal to end of each of the two wires in the lower switch housing. White Wire Blue Wire OF F Turn Power ON Turn Power 1 6 2 7 3 8 4 9 This document is a supplement to the Hunter Installation Manual. Please read and follow the Warnings and Cautions listed in the Hunter Installation Manual that came with your fan. 5 Warning: To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Attach the lower switch housing to the upper switch housing using the three switch housing assembly screws. Tighten all three screws. Note: Not all switch housings attach in the same manner. Check your owner’s manual for details.
Transcript of Blue - Scene7
Installation Without a Stake Light Kit www.HunterFan.com 1.888.830.1326
Using a Phillips Head screwdriver, install the switch housing cap to the lower switch housing using the two
switch housing cap screws.
Switch Housing
CapScrew
Connect the plugs from the upper and lower switch housings. Make sure to line up
the colored markings on the connectors.
Switch Housing
Assembly Screw
Attach the pull chain pendant to the short chain coming from the lower
switch housing.
M0030-01 • 08/24/12 • © Hunter Fan Company
Locate the two light kit screws that attach the light kit to the lower switch housing.
Light Kit Screw
Using a Phillips head screwdriver, remove the two light kit screws from
the light kit which will allow it to be separated from the lower switch
housing.
Light Kit Screw
Disconnect the blue wire in the light kit from the blue wire in the lower
switch housing. Disconnect the white wire in the light kit from the white wire
in the lower switch housing. Install a dummy terminal to end of each of the two wires in the lower switch housing.
White Wire
BlueWire
OFFTurn Power
ONTurn Power
1
6
2
7
3
8
4
9
This document is a supplement to the Hunter Installation Manual. Please read and follow the Warnings and Cautions listed in the Hunter Installation Manual that came with your fan.
5
Warning: To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
Attach the lower switch housing to the upper switch housing using the three
switch housing assembly screws. Tighten all three screws. Note: Not all switch housings attach in the same manner.
Check your owner’s manual for details.
Installation Without a Bowl Light Kit www.HunterFan.com 1.888.830.1326
Using a Phillips Head screwdriver, install the switch housing cap to the lower switch housing using the two
switch housing cap screws.
Switch Housing Cap Screw
Connect the plugs from the upper and lower switch housings. Make sure to line up the
colored markings on the connectors.
Switch Housing
Assembly Screw
Attach the pull chain pendant to the short chain coming from the lower
switch housing.
M0030-01 • 08/24/12 • © Hunter Fan Company
Remove the pull chain extension by disconnecting the breakaway connector.
Pull Chain Extension
Using a Phillips head screwdriver, remove the two light kit screws from the light kit which will allow it to be separated from the light kit adapter
and the lower switch housing.
Light Kit Screw
Light Kit Adapter
Disconnect the blue wire in the light kit from the blue wire in the lower
switch housing. Disconnect the white wire in the light kit from the white wire
in the lower switch housing. Install a dummy terminal to end of each of the two wires in the lower switch housing.
Blue Wire
WhiteWire
OFFTurn Power
ONTurn Power
1
6
2
7
3
8
4
9
This document is a supplement to the Hunter Installation Manual. Please read and follow the Warnings and Cautions listed in the Hunter Installation Manual that came with your fan.
5
Warning: To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
Attach the lower switch housing to the upper switch housing using the three
switch housing assembly screws. Tighten all three screws. Note: Not all switch housings attach in the same manner.
Check your owner’s manual for details.
