bbbt cd 2009 - jkdte. · PDF fileDistributor 3 segment 12 Volt with capacity & HT leads (for...
Transcript of bbbt cd 2009 - jkdte. · PDF fileDistributor 3 segment 12 Volt with capacity & HT leads (for...
1
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this office NIT No.ITI/J/09/862 dated: _25-11-2009
List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO. 1 (2008-2009 Spill over)
Package Name: Equipments
S.
No
Name of the item with Specifications Quantity Rates to be
quoted by the firm
1. Cut model of 4 stroke Petrol engine on stand
Technical Specifications :
Motorized actual working cut sectioned of four strokes four cylinder petrol engine
mounted on sturdy stand. The cutting should enable the working parts visible i.e
connecting rod, Piston, Valve spring Pump, Cooling System & lubrication system.
Suitable Electric motor drive with reduction gear to be provided to understand working
of engine system should be designed for easy visibility & understanding of inner parts &
should be provided with needed parts. The Petrol engine shall be supplied duly painted
with a colour for better understanding. The engine should be cut in such a way to
demonstrate bellow stated parts inovable & stationery parts.
1. Cylinder Head 2. Engine Block 3. Piston, Piston, Piston ring & connecting rod 4.
Crank shaft, 5. Timing gear/chain 6, Fly wheel 7. Valves (Operation & timing 8. Oil
Fitter & Pump 9. Water Pump & Radiator 10. Air Cleaner 11. Intake & Exaust manifold
12. Starter motor 13. Alternator 14. Silencer 15. Carburetor 16. Distributor 17. Radiator
18. Oil Sump. 19. Cooling Fan 20. Tappet Cover. 21. Spark Plug 22. Deep Stick with
suitable stand & Manual will also be provided.
01 No
2. Cut model of 2 stroke Petrol engine on stand Actual cut model of 2 stroke petrol Engine, two cylinder cut to show internal details
such as piston connecting rod, suction and exhaust manifold. The cut section should be
colored properly. The model must be hand driven for its working operational
movements. The engine is cut to demonstrate below stated movable and stationery parts.
1) Piston 2) Connecting rod 3) Crank shaft 4) Cylinder block and head 5) Silencer 6)
Carburetor 7) Magneto assembly.
The cut section is mounted suitable stand & is colored. Required parts are provided for
01 No
2
working condition of two stroke petrol engine. Manual is also provided.
3. Cut model of 4 stroke diesel engine on stand CRDI Type A latest motorized 4 stroke 4 cylinder diesel engine, cut model, Water cooled along
with all accessories, Radiator, Fuel Tank, Alternator, Battery, Starter Motor, Cooling
Fan, Frame with Panel Board, Specification Board, Exhaust System with Catalytic
converter. Following parts should be externally showing in working condition by AC or
DC operated * Valve Mechanism
* Piston Assembly * Oil pump Assembly * Water pump * Radiator & Thermostat Valve
* Air Intake System (Air Filter & Turbo Charger). * Fuel Injector * Fuel Injection Pump
* Fuel Feed Pump * Fuel Filter * Water Separator *Fuel Tank *Starter Motor &
Alternator * Timing Gear.
NOTE
1) Engine should be mounted on C Channel Frame. 2) Operating Manual and parts catalogue should be provided.
01 No.
4.
Petrol engine 4 stroke in running condition fitted with MPFI
A Latest model – 4 cylinder Petrol Engine in running condition. Water Cooled along
with all accessories. Radiator, Fuel Tank, Alternator, Battery (12 Volt 11 Plates Reputed
Brand), Starter Motor, Cooling Fan, Panel Board with Warning Instruments such as
Starting Switch, Speed Control Lever temp, gauge, charging lamp, etc.
NOTE
1) Engine should be mounted on C – Channel Frame. 2) Machine manual in original should be provided with details of machine,
accessories, components, mounting, detailed power circuit, control circuit,
Trouble shooting fault and remedies etc.
01 No.
3
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this NIT No.ITI/J/09/862 dated: 25-11-2009
List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO.2 (2008-2009 Spill over)
Package Name: Machinery
S.
N
o.
Name of Item with specifications Quantity Rates to be quoted by
the bidder
6. Wheel balancing machine with accessories
. 14” LCD High resolution color video graphic display.
. Possibility of writing one’s own name or a message on the initial screen
. Possibility of varying the tolerance function from 1 to 10 grams
. Possibility of unbalance display in 1 gram to 5 grams (0.1 oz to ¼ oz)
. Measurement for 2 planers as well as for 1 plane is possible
. Automatic Distance and Automatic Rim Diameter entry
. Balancing accuracy 1 gm
. Data entry keyboard-digital Data input
. Static Optimization Programme
. 4 Alloy rim Program ALU1, ALU2, ALU3, ALU4.
. Self calibration
. Operational Error code display.
. Single phase Low spin motor 200 rpm
. Heavy Duty shaft
. Automatic stop mechanism after measurement cycle Electronic de injection
braking.
Technical Specification
Measuring Mode : Simultaneous measurement if inner & outer unbalance by a single
spin
Measurement Range : Rim dia 10”, 24” or 265-615mm
Rim width 1.5”, 20” or 40-510mm
Distance 0-18cms
01 No.
4
Threshold Unbalance visualization : 5 gms
Braking : Electronic de injection braking
Accuracy : 1 gm
Cycle Time : 7-12 sec.
Power Supply : 220-230V Single Phase
Motor : 0.25 KW
Standard Accessories : Weight Plier, Width Caliper,
Threaded shaft Assembly with Centering Cones.
Make-Any reputed company having ISO Certification.
7. Hydraulic jack with trolley capacity 3 ton
Make- Any reputed company having ISO Certification/ISI standards.
3) Note : The equipment will be supplied with necessary tools, attachments.
01 No.
8. Engineers stethoscope Make-Any reputed company having ISO Certification 01 No.
9. Distributor 3 segment 12 Volt with capacity & HT leads (for Maruti 800)
Make-any reputed company having ISO Certification
01 No.
10
.
Carburetor Down draft, double Ventury (Maruti 800)
Manke-any reputed company having ISO Certification
02 No.
11 Tandem master cylinder with booster.
Make-any reputed company having ISO Certification
01 No.
12
.
Compression testing gauge to read 0 to 115 Kg/sq.cm.
Make-any reputed company having ISO Certification
01 No.
13 Vacuum gauge to read 0 to 760mm of Hg.
Make-any reputed company having ISO Certification
01 No.
14 Disk brake with caliper assembly Maruti 800
Make-any reputed company having ISO Certification
01 Pair
15
.
Battery charges 6-24V with 10A rate
6Vx4 Battery
12Vx2 Batery
Input Volt-230 A.C. 50 Cycle
Output volt-24 D.C.
Rotary switch to select volt & Amp. Input & output Fuse, Pilot light, Ampere meter,
Main
Switch, + Knobs, Diode circuit
Dimension – 23 cm x w 28cm x D 23.5 cm (approx)
Weight : 6.800 kg (approx)
Manual Should be Provided. Make-any reputed company having ISO Certification
03 No.
5
16
.
Battery 12V (Lead acid/Alkaline) (90AH)
Make-any reputed company having ISO Certification
06 No.
17
. Electronic engine control module
Suitable E.C.U. for LMV Vehicle
Make-any reputed company having ISO Certification/ISI standards.
Note : The equipment will be supplied with necessary tools, attachments and standard
Accessories etc. Tenderer should mention list of all standard accessories.
01 No.
18
.
Starter motor axial type, pre-engagement type & Coaxial type 12V DC
Make-any reputed company having ISO Certification/ISI standards.
01 each
19
.
Electrical horn (different types) 12V DC
Make-any reputed company having ISO Certification/ISI standards.
02 No.
20
.
Wiper motor assembly 12V DC Make-any reputed company having ISO
Certification/ISI standards.
01 No.
21
.
Glow plug. Pencil type/Coil Type, Make-any reputed company having ISO
Certification/ISI standards.
02 No.
22 Alternator, 14V 38/65A, Make-any reputed company having ISO Certification/ISI
standards.
01 No.
23 Glow Plug Tester. Make-any reputed company having ISO Certification/ISI standards. 01 No.
24 Starter test bench. Make-any reputed company having ISO Certification/ISI standards. 01 No.
25 Dynamo and voltage regulator. Make-any reputed company having ISO Certification/ISI
standards.
01 each
26 Horn and Horn relay (Bosch) 12V DC 30A
Make-any reputed company having ISO Certification/ISI standards.
01 each
6
27 Engine control sensors 8 type For Maruti-800
Make-any reputed company having ISO Certification/ISI standards.
Note: The equipment will be supplied with necessary tools, attachments and standard
accessories, etc. Tenderer should mention list of all standard accessories specification:-
1) ECU 2) Absolute Pressure Sensor 3) Throttle Position Sensor 4) Intake Air
Temperature Sensor 5) Lambda sensor 6) TDC Sensor 7) Engine Coolant Temperature
Sensor 8) Engine RPM Sensor
01 each
28 4 Point relays 12V DC 30A Make-any reputed company having ISO Certification/ISI
standards.
02 No.
29 5 Point relays 12V DC 30A.Make-any reputed company having ISO Certification/ISI
standards.
02 No.
7
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this office NIT No.ITI/J/09/862 dated: 25-11-2009
List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO.:-3 (2008-2009 SPILL OVER)
Package Name :- Tools/Instruments
S.
No
Name of the item with Specifications Quantity Rates to be
quoted by the firm
1. Spanner Double ended open, Drop forged size (6x7to30x32mm) (set of 12) made
of Chrome vanadium steel, chrome polished make-any reputed company having
ISO certification
05 set
2. Spanner double ended ring-Drop forged size (6x7 to 30x32mm) (set of 12) made of
Chrome Vanadium steel, chrome polished make-any reputed company having ISO
certification
05 set
3. Socket Spanner with handle, T-bar, ratchet and universal set of 24 pcs (8mm to
32mm) with required necessary handles (complete set) made of Chrome Vanadium
steel, chrome polished make – any reputed company having ISO Certification
05 set
4. Combination Pliers, 150mm Chrome Vanadium Steel Hardened and tempered
induction hardened. Make any reputed company having ISO Certification
08 Nos.
5 Round Nose plier, 150mm Chrome Vanadium steel; hardened and tempered
induction hardened, Make any reputed company having ISO Certification
08 Nos.
6. Flat Nose Plier, 150mm Chrome vanadium steel hardened and tempered induction
hardened. Make any reputed company having ISO Certification
08 Nos.
7. Circlip plain internal, 150mm Chrome vanadium Steel hardened and tempered
induction hardened. Make any reputed company having ISO Certification
08 Nos.
8 Circlip plain external, 150mm Chrome vanadium Steel hardened and tempered
induction hardened,. Make any reputed company having ISO Certification.
08 Nos.
8
9. Hammer 0.5kg ball peen with handle. Make any reputed company having ISO
Certification.
08 Nos.
11 Sledge Hammer 8 Kg. cross. Make any reputed company having ISO Certification. 02 Nos.
12 Screw Driver 200mmx9mm blade Ergonomic Handle design, fully hardened blade
of High Grade steel. Make any reputed company having ISO Certification.
08 Nos.
13. Screw Driver 300mmx9mm blade Ergonomic Handle design, fully hardened blade
of High Grade steel. Make any reputed company having ISO Certification.
08 Nos.
14. Side cutting Plier, 150mm Chrome vanadium Steel hardened and tempered
induction Hardened. Make any reputed company having ISO Certification.
08 Nos.
15 Mallet Plastic 0.25Kg. Make any reputed company having ISO Certification. 08 Nos.
16. AVO Motor Analog p3. Make-any reputed company having ISO certification 08 Nos.
17. Feeler Gauge with 20 blades (metric). Make-any reputed company having ISO
certification
04 Nos.
18 Cleaning Tray Aluminium 45cmx60cm 16 Gauge. Make-any reputed company
having ISO certification
04 Nos.
19 Cleaning Tray Iron 60cmx75cm with handle. Make-any reputed company having
ISO certification
04 Nos.
20 Tool Box with lock and Key. Make-any reputed company having ISO certification 08 Nos.
9
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this office NIT No.ITI/J/09/862 dated 25-11-2009
List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO.:-4 (2008-2009 SPILL OVER)
Package Name :- Tools/Instruments COMPUTER
S.N
o.
Name of the Item Quantity Rates to be quoted
by the bidder
1 Windows XP Operating System 01 No.
2 MS-Office 2000 01 No.
3 External Modem 01 No.
4 Laptop 01 No.
10
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this office NIT No.ITI/J/09/862 dated: 25-11-2009
List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO.:-5 (2008-09 SPILL OVER)
Package Name :- FURNITURE
S.NO. NAME OF THE ITEM QUANTITY REQD. Rates to be quoted by the Bidders
1 Pigeon Hole Almirah 78"x34"x18" (22guage, 8 Lockers 12 Nos.
2 Steel Almirah 78"x34"x18" (22 guage,5 shelves 15 Nos.
3 Fire buckets 10 Nos.
4 Instructor’s Table 5' x 3' x 2'.6"(square pipe 1" frame 20 guage,
with
3 drawers on one side cupboard with laminated board top
8 Nos.
5 Computer Chair with arms 22 Nos
6
Dual Desk (30" x 14" x 30" with seat, 30" x 10" x 18" square
1" pipe (20 guage))
120 Nos.
7 Lecture Stand wooden 6 Nos.
8 Computer Table 2 ½ x 2 ½ x 2’ 22 Nos.
9 Writing Board Green 4’ x 6’ 06 Nos.
10 Steel Book cases (66” x 33” x 12”) Steel 22 with glass in front with locks 10 Nos.
11
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this office NIT No.ITI/J/09/862 dated : 25-11-2009 List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO.:-6 (2009-10)
Package Name :- EQUIPMENTS (CUT MODELS & CLUTCH ASSEMBLY)
S.
No
Name of the item with Specifications Quantity Rates to be quoted
by the bidder
1. Multi-plate Clutch Assembly with flywheel
Multi-plate clutch assembly with flywheel suitable for Two wheeler Engine
2 Nos.
2. Single plate Clutch assembly
Single Plate clutch assembly with flywheel suitable for LCV
2 Nos.
3. Propeller Shaft with universal joints assembly
Propeller shaft with universal joints assembly suitable for LCV
2 Nos.
4. Cut-Section model of a sliding mesh gear box
A motorized sliding mesh gear box should be cut to visualize the gears and their sliding
movement and main shaft and layshaft. The motor should provide power to driving shaft
and working of gear box can be shown. For power transmission `V’ belt and pulleys may
be used to avoid slip. The cut section should be painted properly. Assembly fitted on
suitable stand duly painted. Required parts provided for working condition of sliding gear
box and manual provided by party.
1 No.
5. Cut-Section model of synchromesh gear box
Cut Sectioned Synchromesh gear box shown be cut to visualized the gears and
synchronized unit, main shaft, Layshaft, Reverse gear, sleeter mechanism. The motor
should to provided power to driving shaft & working of gear box can be shown for power
transmission. `V’ belt and pulleys may be used to avoid slip. The cut section should be
painted properly. The cut section should properly mounted on suitable stand. Required
parts should be provided. If needed working condition of synchromesh gear box & manual
provided by party.
1 No.
12
6. Cut-Section model of differential assembly
Hypoid type differential assembly shown of crown wheel & pinion assembly, Sun & star
Gear cross off electrical motor with reduction gearbox Suitable stand V belt with pulley.
Whole assembly fitted on stand with proper coloured code.
1 No.
13
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this office NIT No.ITI/J/09/862 dated: 25-11-2009
List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO.:-7 (2009-10)
Package Name MACHINERY (DIFFERENT TYPES OF ASSEMBLY)
S.N
o. Name of Item with specifications Quantity Rates to be quoted
by the bidders
7. Rear axle assembly complete with drive shafts & bracke drums (full floating,
semi floating type and ¼ floating)
Rear Axle
Differential assembly
Axle shaft full floating type
Brake drum assembly
Brake pedal
Brake pipe
Oil tank
Master Cylinder
Electrical motor with reduction gear box (V-Belt pulley)
Above all parts mounted on proper colourized strudy stand with all component
properly coloured with colour code
1 No.
8 Conventional front axle assembly and ISF wheel assembly
Conventional Front Axle Assembly Reverse elliod type front axle with brake
assembly, Wheel Assembly consist of Wheel Rim, Tyre, Tube
1 No.
9 Vacuum assisted hydraulic assembly
The vacuum brake will be to be mounted on sturdy stand. A motor driven vacuum
pump to operated brake will be provided, with suitable control Colour code will be
provided for better understanding. System will be provided with below stated part
to make it working Model. Front and rear drum will be cut to show the braking
system in working condition
1 No.
14
10 Air brake assembly
The brand new air brake is to be mounted on sturdy stand. A motor driven
compressor be provide with air tank and it must be able to demonstrate the working
of air brake. The equipment should be supplied duly painted, with a predefined
colour code for better understanding. Assembly should be provided with below
stated parts to make it working model.
Air Compressor
Oil Reverse
Over loaded valve
Stop light switch
Dual brake valve
Air gauge
Low pressure pipe
Low pressure indicator witch
Brake Chamber
Air tank
Brake drum assembly
Brake pedal
Suitable Electric Motor with Reduction Gear box (With V-belt, Pulley)
Brake light
Stub Axle
Brake Hoses & Pipes
To understand the working of Air brake required parts should be provide to make it
complete working model. Necessary manual also be provided. With suitable stand
1 No.
11 Hydraulic brake assembly. (Brake pedal, booster, Tandem master cylinder,
wheel cylinder, brake drum-mock up assembly
Hydraulic brake assembly will be mounted on sturdy stand. The assembly will be
consist of below stated parts to make it working model. Front and rear drum will be
cut to see the breaking system in working condition. The equipment will be
supplied duly painted with a pre-defined colour codes for better understanding
Tandem master cylinder
Wheel cylinder
Brake drum assembly
Brake light unit in working condition
15
Brake pedal
Brake pipe line.
Suitable Electrical motor with Reduction Gearbox to be provided (V belt with
Pulley)
Oil Tank
Front and Rear axle
Required parts will be provided to make it complete working model. Necessary
manual will be provided. Front and Rear drum will be cut to show the parts in
working condition. With suitable stand.
16
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this office NIT No.ITI/J/09/862 dated: 25-11-2009
List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO.:-8 (2009-10)
Package Name MACHINERY (DIFFERENT TYPES OF ASSEMBLY)
S.N
o. Name of Item with specifications Quantity Rates to be quoted
by the bidders
1 Puncture repair Equipment 1 No.
2 Engine cranker with 12V & 24V Ac to DC Power supply system.
Trolley type with Castor wheel, Air Ventilated Cabinet. Input 230 V Single Phase
50 Hz Output 12V, 24V D.C. Rating Amp. 200
1 No.
3 Chain sling alloy steel double leg 10 mm Having 3 meter long each pair link and 2
slip hooks
1 No.
4 Portable crane hydraulically operated with Swiveling & self alignment hook lifting
capacity 1 ton
21. Portable crane
hydraulically
operated with
Swiveling & self
alignment hook
lifting capacity 1
ton
5 Brake lining rivoting machine (foot operated) 1 No. 22
6 Hydraulic Jack-high (trolley type) 2000 Kg. capacity 2 Nos.
7 Lifting Jack screw type 1000/1500 Kg. Capacity
1 No.
8 Hydraulic jack 5 ton
Capacity : 5 Ton
17
Minimum Height 150mm
Length : 900 to 1000 mm
Maximum Height : 500mm Width : 400 to 450 mm
Trolley : 4 Wheel Type with Pressure Relief Valve
1 No.
9 Petrol Injector MPFI SUITABLE FOR LCV 2 Nos.
10 Petrol Fuel Pump of MPFI system MPFI SUITABLE FOR LCV 2 Nos.
11 Fuel injection pump one with pneumatic governor, one with R.Q. governor
and one with R.S.V governor
Fuel injection pump 6 cylinder Diesel Engine pneumatic governor 4 cylinder & 4
cylinder one with R.Q governor and one with RSV
1 No.
each
12 Fuel feed pump (MICO) SUITABLE FOR LCV
14 Valve spring Compressor 1 No.
15 Injectors Multi Hole Type & Pintle Type 1 set
16 Drilling Machine Pillar 20mm capacity with accessories 02 Nos.
17 Spark plug cleaner and tester similar to Bosch/champion
Working Pressure 5 Kg/cm Sq to 13 Kg per Cm Sq.
Plug size M10, M14, M18, Input Voltage 220V A.C., 50 HZ,
Ignition Coil 12 KV, Electronic Vibrator 220/12V
01 No.
18 Welding plant Oxy-Acetylene complete (high pressure ) 02 Nos.
18
GOVERNMENT OF JAMMU AND KASHMIR
OFFICE OF THE SR. PRINCIPAL, INDUSTRIAL TRAINING INSTITUTE, JAMMU
Annexure to this office NIT No.ITI/J/09/862 dated: 25-11-2009
List of Items to be purchased for the year 2009-10 by ITI Jammu
PACKAGE NO.:-9 (2009-10)
Package Name TOOLS & EQUIPMENTS
S.N
o. Name of Item with specifications Quantity Rates to be quoted
by the bidders
1 Horse props 4 No.
2 Shock Absorbers Telescope tyre for commercial vehicle 4 No.
3 Pneumatic operated wrench with all accessories 1 No.
4 Coil spring compressor for suspension spring 1 No.
5 Valve seat cutting tools complete with guides & pilot bar (all engles) in a box 1 set
6 Brake pipe flaring tool 1 No.
7 Tripod axle stand adjustable 1500 Kg Capacity
5 Nos.
8 Wire insulation Stripper for shinning conductors from 0.4mm to 4mm 17 Nos.
9 Electrician testing Pencil (line/Neon tester 17 Nos.
10 Portable Electric drill (Single Phase) 6mm capacity 8 Nos.
11 Multi meter 0 to 1000 Ohms 0.5 to 500 volts 1 No.
19
12 Volt meter 5.0 to 30 V/DC 5 Nos.
13 Ammeter 10.0 to 60 A/DC with external shunt 5 Nos.
14 DC Ohm meter 0 to 300 Ohms, mid scales at 20 Ohms 1 No.
15 Electric Soldering Iron 230 V 60 watts 230V 20 watts 2 Nos.
each
16 High rate discharge tester (cell tester) 2 Nos.
17 Mock up wiring board of automobile wiring system
12 volts system, Starting system, Ignition System, Charging System Lighting
System ,Other System
1 No.
18 Digital Electronics Trainer
Basic concepts of digital electronics. Number systems, binary logic and logic gates.
Design issues for sequential and combination logics. Design, operation and
applications of flip-flops. Analog to digital & digital to analog converters. Internal
architecture of semi conductor memories Programming PAL and PLA. Simulator
for number conversion. K-map simulation. Gate implementation process Converter
design principles. And verification of their truth tables (NOT, OR, AND, NOR,
NAND, EX –OR, EX-NOR). Study and verifications of the laws of Boolean
Algebra and De-Morgan’s Theorems. Study of important TTL terminologies.
Verification of important TTL circuit parameters. Construction and verification of
various types of flip-flops using gates & IC’s (RS,JK, D,T, M/S JK).
Construction and verification of various types of combination circuits such as Half
Adder,. Full Adder, Half Subtract-or, Full Subtract-or, Even/Odd Parity Checker,
Multiplexers, De-multiplexer, Binary to Gray & Gray to Binary converters.
Construction & verification of various types of Up/Down,
Synchronous/Asynchronous, Ripple/Reverse, Ring, Binary, BCD & Decade
Counters.
Construction and verification of 4 Bit Universal Shift Register (SR/SL operation)
Study of 7 segment display and decoder/driver
Many other experiments should be possible using the onboard components and
special veroboard provided. (for use of external components without soldering)
.
02 Nos.
19 Electric Pedestal grinder with two 18cm wheel 02 Nos.
20
20 Compression testing gauge to read 0 to 115 Kg/Sq cm (Petrol & Diesel) 01 No.each
21 Vacuum gauge to read 0 to 760 mm of Hg 01 No.
22 Tachometer to read upto 5000 rpm 01 No.
23 Triple leg grip puller with bearings attachment screw/hydraulic powered max.
spread 80, 160, 250, 450 mm
01 No.
24 Pliers water pump multifix 250mm Long 01 No.
25 Liquified Petroleum Gas (LPG) Cylinder, Regulator and Torch with Burner 02 Nos.
26 Anvil 50 Kgs with Stand 01 No.
27 Bench vice 120mm, 150mm Heavy duty 04
No.each
28 Buffing and Polishing Machine 01 No.
29 Pipe Bending Machine (Hydraulic type) 12mm to 30mm 01 No.
30 Fire fighting equipment
Co2 (5Kg)
06 Nos
31 Spanner Double ended open, Drop forged, size (6x7 to 30x32mm) (set of 12) made
of Chrome vanadium steel, chrome polished make-any reputed company having
ISO certification
25 Sets
32 Spanner double ended ring-Drop forged size (6x7to 30x32mm)(set of 12) made of
Chrome Vanadium steel, chrome polished make-any reputed company having ISO
certification
10 Sets
33 Combination Pliers, 150mm Chrome Vanadium Steel Hardened and tempered
induction hardened. Make any reputed company having ISO Certification
25 Nos.
21
34 Hammer 0.5 Kg ball peen with handle. Make any reputed company having ISO
certification
10 Nos.
35 Sledge Hammer 8 Kg cross, Make any reputed company having ISO certification 04 Nos.
36 Screw driver 200 mm x 9 mm blade Ergonomic Handle Design. Fully Hardened
Blade of High Grade Steel, Many any reputed company having ISO certification
10 Nos.
37 Screw driver 300 mm x 9 mm blade Ergonomic Handle Design. Fully Hardened
Blade of High Grade Steel, Many any reputed company having ISO certification
10 Nos.
38 Feeler Gauge with 20 blades (metric). Make any reputed company having ISO
certification
04 Nos.
39 Cleaning Tray aluminum 45cmx60cm 16 gauge 10 Nos.
40 Micrometer outside 0-25mm, 25 to 50mm, 50 to 75mm,75 to 100mm (Digital type) 02
No’s .each