MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 5

ASSEMBLY INSTRUCTIONS

I. Vario-Slack WALL – wall anchoring for slacklines

The Vario-Slack WALL wall anchoring is part of the Vario-Slack set WW (fi g. 1) and the Vario-Slack set GW (fi g. 2) and is used for fi rmly mounting the slackline to an even concrete wall.

The resistance to fracture on even concrete ground is 2200 daN.

Only use the supplied Fischer dowels (bolt anchor FAZ II 12/120) or similar dowels of a different manufacturer with a clamping depth of at least 110 mm.

The wall anchoring Vario-Slack WALL may only be used for slacklining in combination with the Slackline-Tools products Slack-Grip, Slack-Ratchet CL 30 and the CLASSIC Slackline-Tools band.

We recommend having the Vario-Slack WALL mounted by a specialist.

Scope of delivery for the assembly of the Vario-Slack WALL wall anchoring for each side:

• 1 x Vario-Slack WALL

• 6 x FAZ II 12/120 including washer and M12 nut

• 6 x plastic cap

• 2 x mounting block

• 1 x assembly instructions

Fig.1: Vario-Slack set WW

Fig. 2: Vario-Slack set GW

Mounting blocks

FAZ II 12/120 anchor

Washer

Plastic cap

M12 nut

Fig. 3: Fig. 4:

Recommended mounting height 250 mm above the ground

250

mm

650

mm

600

mm

300

mm

300

mm

300 mm300 mm

Montageanweisung_DE_EN_Vario-Slack_02.2017_eingebettet.indd 5 17.05.17 13:55

MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 6

The Vario-Slack GROUND ground anchoring is part of the Vario-Slack set GG and the Vario-Slack set GW and is used for firmly mounting the slackline to an even concrete floor.

Only use the supplied Fischer female thread anchors RG M12I and an appropriate injection mortar (e.g. Fischer FIS EM or similar products of a different manufacturer; not included in the scope of supply).

The ground anchoring Vario-Slack GROUND may only be used for slacklining in combination with the Slackline-Tools products Slack-Grip, Slack-Ratchet CL 30 and the CLASSIC Slackline-Tools band.

We recommend having the Vario-Slack GROUND mounted by a specialist.

Scope of delivery for the assembly of the Vario-Slack GROUND ground anchoring:

• 1 x floor rack

• 1 x Vario-Slack WALL

• 6 x M12x160 hexagon head screw

• 6 x M12 hexagon nut

• 6 x washer, small

• 6 x washer, large

• 12 x plastic cap

• 2 x M12 RG 18 x 125 female thread anchor

• 2 x M12x60 knurled screw

• 1 x assembly instructions

Fig. 5: Vario-Slack set GG

Fig. 6: Vario-Slack set GW

II. Vario-Slack GROUND – wall anchoring for slacklines

Requirements for assembly• Level concrete surface, cracked or non-cracked, concrete

compressive strength class C 20/25 to C 50/60.

• Concrete thickness of at least 200 mm.

• Space requirements: 740 mm wide and 400 mm high.

• Recommended mounting height above ground: 250 mm.

• Recommended mounting distance between twoVario-Slack WALL wall anchors: 4–6 m, max. 10 m.

• Make sure that both Vario-Slack WALLs are alignedopposite to each other. The slackline must not bepull diagonally!

Assembly Position the Vario-Slack WALL according to the above drawing (fig. 3) using the mounting blocks, and handle the wall anchors (weight: 14 kg) with care.

• Mark the six boreholes on the wall or drill the boreholesimmediately through the Vario-Slack WALL withoutmarking.

• Drill a borehole with a diameter of 12 mm and a depthof at least 150 mm.

• Clean the boreholes.

• Position the Vario-Slack WALL with the FAZ II 12/120anchors plus washers on the wall.

• Tighten the nuts (wrench size: 19) with a tighteningtorque of 60 Nm.

• Apply the supplied plastic caps to the nuts.

• Remove the mounting blocks.

Montageanweisung_DE_EN_Vario-Slack_02.2017_eingebettet.indd 6 17.05.17 13:55

MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 7

Requirements for assembly• Level concrete surface, non-cracked, of concrete

compressive strength class C 20/25 to C 50/60.

• Concrete thickness of at least 150 mm.

• Space requirement: 740 mm wide, 645 mm high and548 mm deep, as well as at least 100 mm of additionalfree space around the anchor.

• Recommended mounting distance: 4–6 m, max. 10 m.

• Make sure that both ground anchors are aligned oppositeto each other. The slackline must not be pull diagonally.

Assembly

Assembly of Vario-Slack WALL and fl oor rack

• Proceed as shown in the drawing above (fi g. 7).

• Insert one of the supplied hexagon head screws withapplied large washer through the centre hole (14 mm)of the upper row on the Vario-Slack WALL.

• Hold the Vario-Slack WALL against the fl oor rack so that itis possible to insert the hexagon head screw into theprovided borehole in the fl oor rack.

• Screw down the supplied hexagon nut and the smallwasher at the rear side of the fl oor rack onto the hexagonhead screw and hand-tighten the hexagon nut.

• Repeat the procedure with the other screws (total amountof screws: 6).

• Now tighten all screws to a maximum tightening torqueof 60 Nm.

Securing the Vario-Slack GROUND to the concrete fl oor

Secure the Vario-Slack GROUND according to the above drawing (fi g. 8) and handle the Vario-Slack GROUND (weight: 36 kg) with care.

• Place the Vario-Slack GROUND at the desired position.

• Mark the position of the boreholes (d) and (dl) through theholes in the rear transverse pipe of the Vario-Slack GROUNDon the fl oor. Mark the centre of the long hole (dl) (to allowfor additional correction).

• Drill through the top layer of the fl oor (max. 4 mm).

• Drill a borehole with a diameter of 20 mm and a depth of130 mm so that the inserted female thread anchors arefl ush with the concrete fl oor.

• Clean the boreholes.

• Observe the specifi ed processing and hardening time forthe mortar.

• Inject the injection mortar beginning at the bottom of theborehole making sure that there are no bubbles.

Tip: Screw the complete knurled screw into the female thread anchor to allow for easier screwing in and for the vertical alignment of the female thread anchor.

• Screw the female thread anchors into the boreholes byhand without a setting tool rotating them slightly until theirupper edge is fl ush with the concrete fl oor.

• Make sure that the female thread anchors are verticallyaligned.

• Allow the mortar to harden completely.

• Remove the knurled screws in case you have inserted themfor screwing in and alignment.

• Position the Vario-Slack GROUND above the female threadanchors on the fl oor.

• Insert the knurled screws (fi rst (d), then (dl)); then tightenthem by hand.

Fig. 7:

Washer, large

M12x160 hexagon head screw

Plastic cap

Washer, small

Plastic cap

M12 hexagon nut

Fig. 8:

(d)

(dl)

600 mmM12 RG 18x125 female thread anchor

M12x60 knurled screw

Montageanweisung_DE_EN_Vario-Slack_02.2017_eingebettet.indd 7 17.05.17 13:55

MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 8

DisclaimerWe do not assume any liability, in particular for the following cases:

• The Vario-Slack GROUND or Vario-Slack WALL is notmounted with the supplied dowels or with similar dowels.

• The Vario-Slack GROUND or Vario-Slack WALL is notmounted on a level concrete floor but on wood orother material.

• The supplied assembly instructions are not observed.

• The applied Vario-Slack GROUND or Vario-Slack WALLis damaged.

We as the manufacturer do not assume any liability for injury, consequential or incidental damage resulting from the use of the Slackline-Tools Vario-Slack WALL. This is only applicable if there are no other mandatory legal provisions.

When using the slackline, please observe the instruction manual “VARIO-SLACK SETS – Vario-Slack Set GG, Vario-Slack Set GW, Vario-Slack Set WW”.

Montageanweisung_DE_EN_Vario-Slack_02.2017_eingebettet.indd 8 17.05.17 13:55