AN-NAJAH NATIONAL UNIVERITY DEPARTMENT OF ELECTRICAL ENGINEERING
39
AN-NAJAH NATIONAL UNIVERITY DEPARTMENT OF ELECTRICAL ENGINEERING THREE PHASE THYRISTOR BRIDGE CONTROLLED BY MICROPROCESSOR PREPARED BY: NABEEL MASSRI MOUSA NASIEF INSTRUCTOR : PROF. MARWAN MAHMOUD 2008/2009 Next
description
AN-NAJAH NATIONAL UNIVERITY DEPARTMENT OF ELECTRICAL ENGINEERING THREE PHASE THYRISTOR BRIDGE CONTROLLED BY MICROPROCESSOR PREPARED BY: NABEEL MASSRI MOUSA NASIEF INSTRUCTOR : PROF. MARWAN MAHMOUD 2008/2009. Next. INTRODUCTION. - PowerPoint PPT Presentation
Transcript of AN-NAJAH NATIONAL UNIVERITY DEPARTMENT OF ELECTRICAL ENGINEERING
AN-NAJAH NATIONAL UNIVERITY
DEPARTMENT OF
ELECTRICAL ENGINEERING
THREE PHASE THYRISTOR BRIDGE CONTROLLED BY MICROPROCESSOR
PREPARED BY:
NABEEL MASSRI MOUSA NASIEF
INSTRUCTOR :
PROF. MARWAN MAHMOUD
2008/2009
Next
Back
SIX PULSELEC PRIDGE RECTIFIER:
o Six pulse bridge is the most common one .
o It can be use to control the speed of DC motors .
o It’s output power could be more than 120KW.
Back
Advantages
o Widely used in three phase dual convertors systems (UPS).
Back
o The thyristors are to be triggered every / 3 .
o Two quadratic operations is possible .
o Could be used in continuous and discontinuous mode.
Back
Properties
building three phase bridge and make investigations about
Its input and output characteristics
Back
555 Timer Astable And Monostable Multivibrator
f = 1.44/(C1(R1+2R2)), wherein f is in Hz if R1 and R2 are in mega ohms and
C1 is in microfarads.
Unijunction Transistor Relaxation Oscillator
Pulse transformers
o We used the idea of zero cross detectoro We used PIC 16F877 to do the triggering program .
Back
Input voltage
Output voltage
START
Thyristor
Read the value of the Input voltage
If value =0v
Delay =(firing angel)
Output the triggering pulse
Back
YY
NN
Triggering at 0 Triggering at 45
Triggering at 90 Triggering at 135
We chose the thyristor to work on which is TIC 116.o 8 A Continuous On-State Currento 400 V to 800 V Off-State Voltage.o Max IGT of 20 mA.
Back
The wave forms for continuous operations.
Back
o immediately from the PICimmediately from the PIC
o Using Triac Photo Coupler (MOC 3020)Using Triac Photo Coupler (MOC 3020)
o Using Transistor Photo Coupler (4N25)
o The complete circuit
Output voltage form at α= 90 ˚Output voltage form at α= 60 ˚
Output voltage form at α= 30 ˚Output voltage form at α= 0 ˚
Input current form at α= 90 ˚Input current form at α= 60 ˚
Input current form at α= 30 ˚Input current form at α= 0 ˚
Output voltage form at α= 90 ˚Output voltage form at α= 60 ˚
Output voltage form at α= 30 ˚Output voltage form at α= 0 ˚
The load angel could be measured by the following equation:
Ф= tan-1(wl/R)
For example:
If R= 16Ω and L= 50mh then the load angle can be calculated as a following:
Ф= 44.5
Note :RL load is tested under discontinuous operation because it dose not affect the shape of output voltage for the continuous operation.
Output voltage form at Ф= 67 ˚Output voltage form at Ф= 55 ˚
Output voltage form at Ф= 36 ˚˚
Output voltage form at Ф= 25 ˚
Input current form at Ф= 67 ˚Input current form at Ф= 55 ˚
Input current form at Ф= 36 ˚˚
Input current form at Ф= 25 ˚
o The bridge could be used to control the speed of DC motorThe bridge could be used to control the speed of DC motorConnected to its output terminal by changing the output voltage Connected to its output terminal by changing the output voltage Which depend on the firing angle Which depend on the firing angle
Output voltage form at α= 90 ˚Output voltage form at α= 60 ˚
Output voltage form at α= 30 ˚Output voltage form at α= 0 ˚
Input current form at α= 90 ˚Input current form at α= 60 ˚
Input current form at α= 30 ˚Input current form at α= 0 ˚
The input current contains high frequencies
These frequencies has badly effects on the electrical network
These frequencies has badly effects on the communication devices
Removing these harmonics is capable by using filters
These harmonics are given by:
Hvd=6,12,18,24,30,………
Fde=300,600,900,1200,1500…………
Using LC resonance circuit
Practically the values of L and C are not available in our market because we need to use non polar capacitor with high capacity and high voltages, also we face problems in finding the suitable value of inductors.
Using low pass filter circuit
Using polar capacitors for large capacity with high voltage rating .
The input current form improved .
Input current form at fc=318Input current form at fc=500
Input current form at fc= 636Input current form at fc=1590
Applications:
1-Power electronic lab unit
2- DC motor speed controller
3-Battery charger
4- Part of uninterrupted power system(UPS).
Discussion and conclusionDiscussion and conclusion
benefits: Improve our skills in designing electronic circuits and
interfaces by using the simple electronic components (resistors, capacitors, transformers and diods), and more complicated components like photo couplers.
Learn how to use the measurement devices and how to take accurate measurement by using multimeter and oscilloscope .
Have a basic idea about how to use microprocessor (PIC), building its basic and program it successfully.
Have a good acknowledgment about the basic power electronics component (thyristor).
Understanding the concepts of power electronic like triggering (firing angel), thyristor turn
Future suggestions :
Varying the firing angle of the thyristor of this circuit by using potentiometer (this need high level of calibration for the thyristor firing angle with the PIC analog to digital by programming ).
Using this circuit in industrial application but for huge applications the thyristor should be changed to be more suitable and stand with high currents.
Use this circuit to build a complete uninterrupted power system ( UPS) .
