AirTub Installation

7/28/2019 AirTub Installation

http://slidepdf.com/reader/full/airtub-installation 1/6

IMPORTANT

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

CAUTION

1. Read these instructions and rules careully. Failure to ollow themcould cause serious body injuries and/or property damages.

2. Check your local electrical saety and plumbing codes. Theinstallation must comply with these guidelines.

3. No modifcations, additions or deletions should be made to the blowerwithout actory approval.

4. Do not relocate blower without prior approval rom the actory.

5. Ensure that a class A ground ault interrupter (G.F.I.) is installed as parto the wiring.

6. Wiring should be permanent. Do not use an extension cord. Have theelectrical part o the installation done by, or approved by, a qualifed

electrician.

7. The blower has no serviceable parts.

INSTALLATION

Air massage bathtub installation

1. Never handle your air massage bathtub by the piping.

2. Do not rest your bath unit on the jets located underneath the bathtub.Make sure that back jets are adequately protected when entering the

unit into your bathroom. Be careul not to hit a wall or door rame withthe back jets.

IMPORTANT

An ac cess panel o 30" x 15" (75cm x 40cm) must be

located near the blower to allow easy servicing i need be.

Final installation

1. IMPORTANT: The blower must not be insulated and must have sucient

air space to permit proper unctioning. Surrounding air should beable to reach the room under the apron or the podium o your bathtub.

2. I actory installed, the optional heating element on your air massagesystem heats the air blown into the bathtub or the comort o the

customer. It will not, under any circumstances, reheat or maintain

the temperature o the bath water.

3. Area underneath and around the bathtub must be cleaned beore

fnalizing the installation to ensure that no wood shavings or otherparticles enter into the air blower and are blown through the jets.

4. Beore flling with water, clean bathtub rom installation debris and dirt.I necessary use a vacuum cleaner.

5. Veriy connection and unctioning o touch pad and air blower beore

fnalizing the installation.

AIR MASSAGE SYSTEM

Introduction

Thank you or your confdence in CG Air Systèmes inc. by purchasing

your new air massage system.We can assure you that CG Air Systèmes inc. uses the best materials and

applies the most strict quality control measures to ensure that each andevery unit meets the highest standards o the Canadian Standard

Association (CSA) and Underwriters Laboratories (UL).

The origins o Air Massage...

Air massage, also known as balneotherapy, is the use o air mixed with

water to gently but eciently massage the body.

Its soothing and pain relieving virtues were already recognized by the

Romans. But, unlike the Romans who could only aord the pleasures o a relaxing and invigorating bath every now and then, the technology

developed by CG Air Systèmes inc. allows you to enjoy the benefts o

balneotherapy every day in your own bathroom.

Sae use o your air massage bathtub

Your new massage system provides you with a gentle, overall massage.

The massage eect is obtained by injecting warm air through air jets intothe bathwater. Using the blower or too long a period at too high water

temperature will cause a tiring eect. When you frst begin to use yourluxury bath unit, set the blower duration at fve minutes maximum.Regulate the water temperature to a moderately warm level. These

levels can be later increased or additional massaging eects.

Your physiological response to a hot massage bath depends on your

age, health and medical history. I you develop a headache or becomedizzy or nauseous, get out at once and cool o under the shower. Get

medical help i the symptoms persist.

Consult your doctor beore you use the massage bath or physicaltherapy o an injury or disorder. Do not take a massage bath without your

doctor’s consent i you are ill, pregnant or i you suer rom high bloodpressure, heart disease or other health problems. Never take a massage

bath while under the inuence o medication, drugs or alcohol.

C a ution: Children or incapacitaded people should not use the massage

bath unattended. Your bath water temperature should not exceed 40ºC

(104ºF).

Ater having cleaned the tub rom all installation debris and dirt, fll withwater at normal bathing water level ie. maximum 2” below the overowwhen bather is sitting in the tub. Never fll the tub with water above the

overow level.

When flling your tub make sure that water temperature does not exceed

70ºC (158ºF). The use o water that is too hot might shorten the lietime

o the o’rings and gaskets o the air jets.

TROUBLESHOOTING

Blower ails to operate

1. Veriy that electronic touch control is connected properly

(Reer to wiring diagram).

2. Check electric power supply. Reset circuit breaker or replace use i

necessary.

3. Check ground ault circuit interrupter. Reset i tripped.

4 I the system has been unctioning or quite some time, it is possible

that the thermic protection has shut o the motor. Let it cool o or atleast 30 minutes beore using it again.

Motor runs, but no air comes through the jets

1. Veriy that the main air hose rom maniold to blower is properly

connected. I necessary, reconnect and tighten clamps.

Air outlets of et heads are obstruded

1. I the air outlets o a jet head are obstructed by soap or other residues,

fll tub with warm water, then switch system ON and OFF several times. The air outlets should be cleared, i this is not sucient, careully tap

on the jet heads with the handle o a screw driver or a similar tool(plastic) while the blower is running.

The air heater seems not to work

1. To veriy the operation o the air heater, fll the bathtub to working level

and operate blower on high turbulence or approximately 5 minutes.

Careully eel the exible connection hose where it connects to theblower. The hose and its immediate area should eel warm to the

touch. I not, contact your local distributor.

2. I your tub is installed against two outside walls, it is recommended to

ensure adequate insulation or these outside walls to minimizeheat loss.

3. Skin sensitive people might experience the so-called “cold air eect”

which is caused by the sensation o air bubbles running along the wetskin and providing the bather with a shivering sensation. Just move

your body slightly away rom the closest jet to stop the sensation o cold air. (NOTE: Even i the outcoming air would be hot enough to burn

the skin, this shivering eect would still persist.)

Note: The air heater is not designed to heat your bath water, just to

preheat the incoming air to body temperature.

The drying cycle

1. Veriy with our electronic control instructions.

For blower models

MILLENIUM: ME · ME-LL · M0 · M0-LL · M3 · MAS · MAST · MS PIGGY: PE · P0 · P3 · PAS · PAST

MILLENIUM & PIGGY1000 _ 10-JANV.-2005



WARRANTY

All air blowers are warranted to be ree o deects in manuacturing,material and workmanship or a period o one year rom the date o purchase by the owner/end-user.

Limitations

This warranty does not apply to the bath tub and/or spa but solely tothe components manuactured by CG AIR SYSTÈMES INC.

This warranty shall not apply to the ollowing incorrect operatingprocedures, breakage or damages caused by ault, abuse, misuse,carelessness, misapplication, alteration, modifcation, impropermaintenance o the unit, as well as act o God, fre, chemical or naturalcorrosion or any other casualty.

The owner o the product covered by the present warranty is entirelyresponsible or the proper installation o the product in accordance withthe installation manual provided. CG AIR SYSTÈMES INC. neither installsnor supervises nor contracts or the installation and consequently cannotbe held responsible or the installation.

CG AIR SYSTÈMES INC. is not responsible or any damages or claimsresulting rom deects that could have been discovered, repaired oravoided by inspection and testing prior to installation.

CG AIR SYSTÈMES INC. makes no express warranty , no warranty ormerchantability, no warranty o ftness or particular purposes, neitherany other warranty implied or statutory or its products other thanspecifed above.

In no event shall CG AIR SYSTÈMES INC. liability exceed the purchaseprice o the deective part.

I within the warranty period, any such product shall prove to bedeective, CG AIR SYSTÈMES INC. reserves the right to repair or replacethe deective product with one o equal value.

Commercial limitations

In addition to the above conditions and limitations, i the product is tobe used as a display, the warranty period begins when the product hasbeen placed on display. Under no circumstances willCG AIR SYSTÈMES INC. be responsible or any proft loss due to amalunction o the unit. This warranty gives the owner/end-user specifc

ME · ME-LL · MO · MO-LL · PE · PO AIR BLOWERS

legal rights and the owner/end-user may have other rights which varyrom one state/province to another.

CG AIR SYSTÈMES INC. reserves the right to discontinue and/or changemodels, colors and specifcations in design together with replacementparts without notice and without incurring any obligations.

ELECTRICAL INSTALLATION

1. The electrical installation is subject to inspection and approval bylocal authorities. All electrical connections must be made by alicensed electrician.

2. Beore beginning installation make sure that electric power is

disconnected at use box.3. The blower must be located out o reach rom the person in the

bathtub and fxed in position with screws.4. The blower connection is pre-installed. Do not remove the blower

cover, this will void the warranty.

5. Reer to your local electrical code i your distance between theinstallation site o the bath unit and the main use box is more than100 eet (30,4 m).

120V Use the actory pre-installed type SJ wire to connect to junctionbox (not provided by the tub manuacturer). Run a separate120V, 60Hz, 15A G.F.I. (Class A protected) electric circuit rom the mainuse box to the junction box. Use a 14 gage three conductor cable(2 wires plus ground) in connections up to 100 eet (30,4m) rom themain use box.

240V Use the actory pre-installed type SJ wire to connect to junction

box (not provided by the tub manuacturer). Run a separate240V, 60Hz, 15A G.F.I. (Class A protected) electric circuit rom the mainuse box to the junction box. Use a 14 gage three conductor cable(2 wires plus ground) in connections up to 100 eet (30,4m) rom themain use box.

FUNCTIONS ME · ME-LL · PE

This blower can be operated by an independent electronic control, air switch or wall timer.

One speed or multispeed depending o the control model. Please reer to the instructions o the electronic control, air switch or wall timer or theoperation o your air system.

FUNCTIONS MO · M0-LL · PO

Your blower is equipped with an integrated air heating element.

This blower can be operated by an independent electronic control, air switch or wall timer.

One speed or multispeed depending o the control model. Please reer to the instructions o the electronic control, air switch or wall timer or theoperation o your air system.



MAS · MAST · M3 · MS · PAS · PAST · P3 AIR BLOWERS

FUNCTIONS MAS · PAS

Your blower is equipped with a built-in ON/OFF air switch

1st press air push: The blower starts at maximum speed.

2nd press air push: The blower stops.

FUNCTIONS MAST · PAST

Your blower is equipped with a built-in electronic control, 1 speedand a 20 minute automatic timer as well as an automatic drying cycle.

FUNCTIONS M3 · P3

Your blower is equipped with a built-in electronic control,

3 speeds: maximum, medium, minimum and a 20 minute automatictimer as well as an automatic drying cycle.


2nd press air push: The blower stops.

Standard function: A drying cycle will automatically startthe blower or 1 minute, 20 minutes

ater the system, stops.


2nd press air push: The blower turns to medium speed.

3th press air push: The blower turns to minimum speed.

4th press air push: The blower stops.

Standard function: A drying cycle will automatically start

the blower or 1 minute, 20 minutesater the system, stops.

FUNCTIONS MS

Your blower is equipped with an integrated air heating element,

built-in electronic control, variable speed, pulsation cycle, a20 minute automatic timer and an automatic drying cycle.

Optional: water level detectors

1

1st press: The blower starts at maximum speed, LED: ON

2nd press: The blower stops, LED: OFF

21st press: Speed goes up, LED: ON when pressing.

Release pressure at the desired speed.

31st press: Speed goes down, LED: ON when pressing.


4

1st press: Speed will vary gradually rom maximum to

minimum and back to minimum, LED: ON

2nd press: System turns of and on, then of again, LED: ashes

3th

press: Returns to maximum speed, LED: OFFStandard function: A drying cycle will automatically start

the blower or 1 minute, 20 minutes ater the system, stops.

1

1st press: The blower starts at maximum speed, LED: ON

2nd press: The blower stops, LED: OFF

21st press: Speed goes up or down, LED: ON when pressing.


3

1st press: Speed will vary gradually rom maximum to

minimum and back to minimum, LED: ON

2nd press: System turns of and on, then of again, LED: ashes

3th press: Returns to maximum speed, LED: OFF

Standard function: A drying cycle will automatically start

the blower or 1 minute, 20 minutes ater the system, stops.

A C 0 5

Optional function with M3 · P3 · MS :

I your blower has been actory set or a 24 hour drying cycle,program as ollows:

1. Determine the time that you wish your drying cycle to starteach day.

2. Completely shut down the electrical current to the bloweror 10 seconds.

3. Start your system or a ew seconds.

Your drying cycle will start every 24 hours rom that moment on.

In case o a power ailure, reprogram as needed.

1

32



INSTALLATION INSTRUCTIONS FORR E M O T E C O N T R O L

R E M O T E C O N T R O L1 4 0 0 0 · E N G L I S H

PRINTED AND M ANUFAC TURED IN CA NADA

One (1) remote c ontrol Two (2) magnets One (1) rec eiver module One (1) c able

T h e f o l l o w i n g c o m p o n e n t s a r e n e c e s s a r y

2006-07-05

WARNING: The magnets are extremely p owerful despite their small size. Use caution while installing and

handling to avoid injuries ca used by a sudde n movement of the magnets clinging together and po ssibly

pinching fingers, skin or o ther. Persons with physical conditions that could be affec ted by magnetic fields

should a void using it and/or consult with their physician.

A. Determine a ppropriate loc ation for the remote control in the ba thtub.

R E M O T E C O N T R O L I N S T A L L A T I O N

1

Determine backside location of magnets

A. Hold the remote co ntrol in the chosen loc ation.

B. From the exterior of the ba thtub position thesupplied magnets, the attrac tion force willguide you to the prope r area and they will holdin place.

C. Ma rk the position of the magnetswith a markeror pencil.

2

Install magnets on backside

A. Apply a dab of silicone to the magnets, placeand maintain in the premarked position.

B. Let dry in this position.

3

CAUTION: Ma gnets always have a positive and

negative side and will only be attrac ted to one

side. C onsider this to a void applying the silicone

to the wrong side.



INSTALLATION INSTRUCTIONSFORR E M O T E C O N T R O L

R E M O T E C O N T R O L

1 4 0 0 0 · E N G L I S H

2006-07-05

Receivermodule installation

A. The receiver module must be installed under the ba thtub rim.

R E C E I V E R M O D U L E I N S T A L L A T I O N

1

The remote c ontrol only operates C G Air Systèmes

MilleniumMS+& SilverSLS+blower series and C G Air elec tronic c ontrols Evolution

S Y N C H R O N I Z A T I O N

Remote control and keypad usedto activate the system

A.Plug in the cables as shown on the drawing

B. Onc e everything is connec ted, the remotecontrol is ready for synchronization

2.ARECEIVERMODULE

KEYPAD REMOTECONTROL

BLOWER ORELECTRONIC CONTROL DISPLAY

OR

Remote control only,to activate the system

A.Plug in the c ab le a s shown on the drawing

B. Onc e everything is connec ted, the remotecontrol is ready for synchronization

2.B

BLOWER ORELECTRONIC CONTROL

RECEIVERMODULE

REMOTECONTROL

A.Once the system has been connected,the remote c ontrol must be synchronized with its rec eiver module.

B. Switch off the main breaker or unplug the system and switch it on again.

C.From this moment, you have 15 sec onds to p roc eed with the synchronization.

D. Press simultaneously on the button 2 +3 of the remote for 4 sec onds.

E. The remote control is now synchronized and ready to use.

F. If the synchronization is not successful the first time, you should resynchronize, starting from step B.

RECEIVERMODULE

IMPORTANT:

· In order to o btain the best rec eption po ssible, we rec ommend not to installthe receiver module next to the fauc ets or metal piping.

· Loc ation of the rec eiver module must be easily accessible

from the outside of the bathtub for maintenance.



Product Catalog - V.02

T: (418) 935-7075 · 1-800-463-9927 · F: (418) 935-3507 · www.cgair .com

PERFORMANCE GRAPHICS

2 3 5 6 8 101 4 7 932

50

68

86

104

122

140

158

0

10

20

30

40

50

60

70

T E M P E R A T U R E

TIME(MINUTES)

The graphic curves shown are approximateand can vary depending on the installation.

Temperatures are taken on a 16 air jetsystem using a Silver blower.

WITH 300W HEATING ELEMENT

WITHOUT HEATING ELEMENT

BLOWER OUTLET AIR TEMPERATURE

AirTub Installation

Documents

Transcript of AirTub Installation