AIR CONDITIONING - Toyota-Tech.euBDD59F94-C062-4B8A-80A5-428CAD… · inside engine compartment...
-
Upload
dangnguyet -
Category
Documents
-
view
216 -
download
0
Transcript of AIR CONDITIONING - Toyota-Tech.euBDD59F94-C062-4B8A-80A5-428CAD… · inside engine compartment...
INS
IDE
EN
GIN
E C
OM
PA
RT
ME
NT
TOYOTA
ENGLISH
AIR CONDITIONING
EUROPE,GENERAL,AUSTRALIA
© 2001 DENSO CORPORATION
All Rights Reserved. This book may not be reproduced or copied,
in whole or in part, without the written permission of the publisher.
INTRODUCTIONIMPORTANT NOTICE
DEFINITION OF TERMS
FOREWORDThis manual has been published to explain how to install the air conditioning for TOYOTA COROLLA. When installing the air conditioning, installation should be performed as described in this manual.
[APPLICATION VEHICLE]
CAUTION
[DOCUMENT CODE AND DOCUMENT PART NUMBER]
This manual has been designed for technicians who are qualified and educated in the proper procedures of vehicle safety, handling and maintenance; experienced in installation of car air conditioning or who are able to carry out installation procedures when given instructions by an experienced technician in a supervisory capacity; and are certified to handling refrigerant. 1. Take special care to ensure that clearance between air conditioning components and other components such as
brake parts, fuel system and electric wires as specified in this manual.2. If a problem is found with the air conditioning system due to installation, refer back to the manual to correct the
problem(s).3. Vehicle and air conditioning kit components as well as installation procedures are subject to change without
prior notice. Refer to the latest installation manual and service information. Any changes affecting the above items will be given in the form of a “Installation instructions for air conditioning (Supplement)” (issued by DENSO) or a service bulletin (issued by the manufacturer).
WARNING : Describes precautions that should be observed in order to prevent injury or death to the user during installation.
CAUTION : Describes precautions that should be observed in order to prevent damage to the vehicle or its components, which may occur during installation if insufficient care is taken.
NOTE : Provides additional information that facilitates installation work.
FRONT,REARLEFT,RIGHT
: Shows the direction when viewed from the driver’s seat.
VEHICLE NAME MODEL CODE PRODUCTION PERIOD ENGINE TYPE STEERING POSITION
COROLLA NZE12#R 2000.8~ 1NZ/2NZ-FE RHD
ZZE12#R 1ZZ/3ZZ/4ZZ-FE,2ZZ-GE
1. Carefully read the separate manual "GENERAL INFORMATION/AFTER INSTALLATION" before and after installation.
2. Refer to the separate manual "INSTALLATION MANUAL (INSIDE PASSENGER COMPARTMENT)" for details on installation for the passenger compartment side.
MANUAL NAME DOCUMENT CODE DOCUMENT PART NUMBER
GENERAL INFORMATION /AFTER INSTALLATION
AOAMC-01* 988963-475*
INSTALLATION MANUAL(INSIDE PASSENGER COMPARTMENT)
AAAMB-24* 988963-455*
- 1
005001
VEHICLE HARNESS
BATTERY
Disconnect the negative cable first.
AC1895
ENGINE COVER
AC3568
1ZZ-FE E/G MODEL ONLY
1. INSTALLATION INSIDE PASSENGER COMPARTMENT
CAUTION
1. Before starting installation, remove the negative cable from the battery.
2. Before making any hoses and tubes connections, apply a few drops of compressor oil to the seat of O-ring and coupling nuts.
3. When tightening and loosening the fittings, use two wrenches for support.
4. Ensure fender covers are in position.5. Start the work from the inside passenger
compartment side.
CAUTION
First remove the negative terminal on the battery and the vehicle harness connection before installing the equipment.
(1) REMOVAL OF ORIGINAL PARTS
� 1ZZ-FE E/G MODEL ONLY [(a)](a) Engine cover-
07
- 2
005001
FRONT
AC4368
BATTERY
BATTERY TRAY
AC4369
VEHICLE HARNESS
AIR CLEANER BOX UPPER COVER
AIR CLEANER HOSE
VSV
FRONT
AIR CLEANER BOXUPPER COVER
VSV
HOOK
AC4370
FRONT
AC4371
FILTER
(b) Battery and battery tray
(c) Disconnect the vehicle harness from the air
cleaner box upper cover.(d) Disconnect the air cleaner hose from the air cleaner box upper cover.
(e) Temporarily remove the air cleaner box upper cover from the air cleaner lower cover.
(f) Temporarily remove the VSV from the air
cleaner box upper cover.CAUTION
Do not disconnect the intake hoses from the VSV.
(g) Filter
-
07
- 3
005001
FRONT AC4372
VEHICLE HARNESS CLAMP
AC4373
AIR CLEANER BOX LOWER COVER
FRONT
FRONT
AC4374
AIR DUCT
FRONT GRILLE AC3569
RADIATOR UPPER SUPPORTS (RH,LH)
(h) Vehicle harness clamp
(i) Air cleaner box lower cover
(j) Air duct
(k) Radiator upper supports. (RH,LH)
(l) Front grille-
07
- 4
005001
FRONT FENDER LINER (LH) SCREWS AC3570
CLIPS
AC4379
STEERING WHEEL
FRONT BUMPER
AC3571
SCREW
VEHICLE WITH SURGE TANK ONLY
AC3572 SURGE TANK
VEHICLE WITH SURGE TANK ONLY
(m) Front fender liner (LH)
NOTETake care not to remove the front fender liner (LH)completely.
(n) Fully turn the steering wheel counterclockwise,
before removing the front fender liner (LH).� VEHICLE WITH SURGE TANK ONLY [o)~(p)]
(o) Screw(p) Surge tank
-
07
- 5
005001
SCREWSAC4381
UNDER COVER (RH)
CLIPS
CLIPS
CLIP
RESISTOR
BOLTS(M6 16)
AC4382
FRONT
AC4383
VEHICLE HARNESS(2-P)
TAPING
TO RESISTOR
RESISTOR
VEHICLE HARNESS(2-P)
AC4384
(q) Under cover (RH)
(2) RESISTOR
(a) Install the resistor to the body using two bolts.(b) Pull the vehicle harness (2-P) down.
(c) Route the vehicle harness (2-P) to the resistor.(d) Connect the vehicle harness (2-P) to the
resistor.-
07
- 6
005001
FRONT
FAN SHROUD AC4423
RADIATOR FAN MOTOR
VEHICLE HARNESS
VEHICLE HARNESS CLIP
VEHICLE HARNESS CLIP
FRONT
LIQUID TUBE No.1
RADIATOR
AC4385
FRONT
AC4386
LIQUID TUBE No.1
VEHICLE HARNESS
LIQUID TUBE No.1
AC4424
FRONT
(3) LIQUID TUBE(a) Disconnect the vehicle harness from the radiator
fan motor.(b) Temporarily remove the vehicle harness clip
from the fan shroud.
(c) Insert the liquid tube No.1 as shown in the left
figure.(d) Route the liquid tube No.1 under the vehicle
harness, when inserting the liquid tube No.1.(e) Set the liquid tube No.1 as shown in the left
figure.-
07
- 7
005001
AC4420CONDENSER
COLLARS
BUSHINGS
RADIATOR
CORRUGATED BOARD AC4387
CONDENSER
CONDENSER
CONDENSER
AC4388
VIEWED FROM THE BOTTOM SIDE OF VEHICLE
VIHICLE HOLE
VIHICLE HOLE
RUBBER CUSHION
RUBBER CUSHION
(4) CONDENSER(a) Assemble two collars and two bushings to the
condenser.
(b) Lean the radiator backward then insert the
condenser in front of radiator.CAUTION
Insert a corrugated board and others beforeinserting the condenser to prevent the radiator frombeing damaged.
(c) Make sure that the bushings of condenser
-
positively inserted into the vehicle holes.
07
- 8
005001
CONDENSER
AC4389
BOLTS (M8 32,SILVER)
FRONT
FAN SHROUD AC4425
RADIATOR FAN MOTOR
VEHICLE HARNESS
VEHICLE HARNESS CLIP
VEHICLE HARNESS CLIP
ADJUSTING BOLT
LOCK BOLTAC3573
ALTERNATOR BELT(DISCARD)
1NZ/2NZ-FE E/G MODEL ONLY
(d) Install the condenser using two bolts.
(e) Reinstall the vehicle harness clip to the fan
shroud.(f) Reconnect the vehicle harness to the radiator fan motor.
(5) COMPRESSOR AND COMPRESSOR DRIVE
BELT� 1NZ/2NZ-FE E/G MODEL ONLY [(a)~(g)](a) Loosen the lock bolt and the adjusting bolt.(b) Remove and discard the alternator belt.-
07
- 9
005001
(c) Install the compressor to the engine block using four bolts.
CAUTION
Tightening Torque
24.5 N•m (250 kgf•cm, 18.1 lbf•ft)
Tightening order; [1] » [2] » [3] » [4]
COMPRESSOR
ENGINE BLOCK
AC3574
BOLTS(M8 72)
1NZ/2NZ-FE E/G MODEL ONLY
[3]
[4]
[2]
[1]
-
07
- 10
005001
1NZ/2NZ-FE E/G MODEL ONLY
AC3575
COMPRESSOR DRIVE BELT
COMPRESSORPULLEY
WATER PUMPPULLEY
CRANKSHAFT PULLEY
ALTERNATOR PULLEY
10kgf
ROD
FRONT
ALTERNATOR
OCV
ALTERNATORADJUSTING BAR
COMPRESSOR DRIVEBELT
ADJUSTING BOLT
LOCK BOLT
AC3576
1NZ/2NZ-FE E/G MODEL ONLY
(d) Install the compressor drive belt to the pulleys as shown in the left figure.
CAUTION
(e) Adjust the belt tension as shown in the left figure.
CAUTION
1. The threads on the compressor belt must fit intogrooves on the pulley.
2. The belt tension must be measured betweenthe specified pulleys.
3. The tension may be measured between any
pulleys when using the DENSO belt tensiongauge.
4. Adjust the belt to the center of the range.5. Adjust the belt by tightening the adjusting bolt.
Belt deflection at 98 N•(10 kgf,22 lbf) force
Belt tension using the belt tension gauge
New Belt 7.0-8.5 mm(0.28-0.33 inch)
539-637 N(55-65 kgf, 121-143 lbf)
Used Belt (Re-adjustment)
11.0-13.0 mm(0.44-0.51 inch)
245-392 N(25-40 kgf, 55-88 lbf)
Insert the rod between the alternator adjusting bar and the engine mount bracket, and adjust the belt tension.Do not insert the rod between the alternator adjusting bar and OCV since the OCV might get damaged.
(f) Tighten the adjusting bolt.
(g) Tighten the lock bolt.
Tightening Torque
18.5 N•m (189 kgf•cm, 13.6 lbf•ft)
Tightening Torque
54 N•m (550 kgf•cm, 40 lbf•ft)
-
07
- 11
005001
NOTE
AC3577
FRONT
ALTERNATOR BELT(DISCARD)
1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL ONLY
FRONT
BOX-END COMBINATIONWRENCH (19mm)
� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL ONLY[(h)~(l)]
(h) Use the following procedure to remove the alternator belt.
NOTE
(i) Remove and discard the alternator belt.
Set the box-end combination wrench (19mm) as shown in the left figure, and remove the alternator belt to the pulleys while pulling the box-end combination wrench to the front of the vehicle.
-
07
- 12
005001
(j) Install the compressor to engine block using three bolts.
CAUTION
Tightening Torque
24.5 N•m (250 kgf•cm, 18.1 lbf•ft)
Tightening order; [1] » [2] » [3]
COMPRESSOR
ENGINE BLOCK
AC3579
BOLTS(M8 72)
[3]
[1]
[2]
1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL ONLY
-
07
- 13
005001
NOTE
FRONT
COMPRESSOR DRIVE BELT
AC3580
1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL ONLY
FRONT
BOX-END COMBINATIONWRENCH (19mm)
AC3578
TENSIONERPULLEY
P/S PUMP PULLEY ORIDLE PULLEY
ALTERNATOR PULLEY
WATER PUMPPULLEY
COMPRESSORPULLEYCRANKSHAFT PULLEY
1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL ONLY
TAPING
VEHICLE HARNESS (4-P)
FRONT
AC4394
(k) Use the following procedure to install the compressor drive belt.
NOTESet the box-end combination wrench (19mm) as shown in the left figure, and install the compressor drive belt to the pulleys while pulling the box-end combination wrench to the front of the vehicle.
(l) Install the compressor drive belt to the pulleys as
shown in the left figure.(m) Pull the vehicle harness (4-P) down.
-
07
- 14
005001
FRONT
VEHICLE HARNESS(4-P)
Mg/C CONNECTOR
AC4395COMPRESSOR
FRONT
AC4397
PLASTIC CLAMP No.2
(n) Connect the vehicle harness (4-P) to the Mg/C connector.
� PIPING LAYOUT
COMPRESSOR
CONDENSER
LIQUID TUBE No.1
PLASTIC CLAMP No.1
LIQUID TUBE No.2
PLASTIC CLAMP No.2
PLASTIC CLAMP No.3
DISCHARGE HOSE
SUCTION HOSE
BRACKET No.2
BRACKET No.1
FRONT
TO PASSENGER COMPARTMENT
AC4396
(6) PIPING
(a) Install the plastic clamp No.2 to the body.-
07
- 15
005001
CONDENSER AC4421
LIQUID TUBE No.1
PLASTIC CLAMP No.1
BOLT(M6 25)
FRONT
AC4398
BOLT(M6 12)
BRACKET No.1
LIQUID TUBE No.2
AC4399PLASTIC CLAMP No.2 FRONT
LIQUID TUBE No.1
PACKING
PACKING
CROSSSECTION
QUICK JOINT (SMALL) AC4400
LIQUID TUBE No.2
BRACKET No.1
FRONT
(b) Assemble the plastic clamp No.1 to the condenser.
(c) Connect the liquid tube No.1 to the condenser using a bolt.
(d) Fasten the liquid tube No.1 to the plastic clamp No.1.
Tightening Torque
5.4 N•m (55 kgf•cm, 4.0 lbf•ft)
(e) Install the bracket No.1 to the body using a bolt.
(f) Connect the liquid tube No.2 to the liquid tube
No.1.(g) Fasten the liquid tube No.1 to the plastic clamp No.2.
(h) Attach the packing around connecting portion of the liquid tube No.1 and liquid tube No.2.
(i) Route and connect the liquid tube No.2 to the
liquid and suction tube.(j) Fasten the liquid tube No.2 to the bracket No.1.(k) Fasten the liquid tube No.2 using a quick joint
(small).
-
07
- 16
005001
BRACKET No.2
FRONT
AC4401
CAUTION
BOLT(M6 12)
AC4402
PLASTIC CLAMP No.3
FRONT
FRONT
SUCTION HOSE
AC4403COMPRESSOR BOLT(M6 35)
AC4404
SUCTION HOSE
NUT (M6)
FRONT
BRACKET No.2
(l) Install the bracket No.2 to the body using a bolt.
CAUTION
Catch the turning stopper to the vehicle holesurely.
(m) Install the plastic clamp No.3 to the body.
(n) Connect the suction hose to the compressor
using a bolt.Tightening Torque
9.8 N•m (100 kgf•cm, 7.2 lbf•ft)
(o) Fasten the suction hose to the bracket No.2
using a nut.-
07
- 17
005001
QUICK JOINT (BIG)
AC4405
SUCTION HOSE
FRONT
SUCTION HOSE
PLASTIC CLAMP No.3
AC3585
FRONT
DISCHARGE HOSE
DISCHARGE HOSE
AC4407
DISCHARGE HOSE
CONDENSER
FRONT
BOLT (M6 25)
(p) Connect the suction hose to the liquid and suction tube.
(q) Fasten the suction hose to the plastic clamp No.3.
(r) Fasten the suction hose using a quick joint (big).
(s) Insert the discharge hose as shown in the left
figure.(t) Connect the discharge hose to the condenser
using a bolt.Tightening Torque
5.4 N•m (55 kgf•cm, 4.0 lbf•ft)
-
07
- 18
005001
FRONTDISCHARGE HOSE AC3584
COMPRESSOR
BOLT(M6 35)
FRONT
TAPING
AC4409
VEHICLE HARNESS (4-P)
AC4410
VEHICLE HARNESS (4-P)
PRESSURE SWITCH
FRONT
RELAY BOX COVER
AC4411
(u) Connect the discharge hose to the compressor using a bolt.
Tightening Torque
9.8N•m (100 kgf•cm, 7.2 lbf•ft)
(v) Pull the vehicle harness (4-P) down.
(w) Connect the vehicle harness (4-P) to the
pressure switch.(7) RELAYS
(a) Temporarily remove the relay box cover.-
07
- 19
005001
FRONT
Mg/C RELAY (4-P,BLACK)
AC4412
FRONT
RELAY BOX COVER
AC4413
AC3581
CAUTION PLATE
SCREWSAC4381
UNDER COVER (RH)
CLIPS
CLIPS
CLIP
(b) Install the Mg/C relay into the relay box.
NOTEBe sure to install the relay box by supporting therelay box by hand from the bottom side to preventa contact defect.
(c) Reinstall the relay box cover.
(8) CAUTION PLATE
(a) Attach the caution plate to the frame.NOTEAffix after completely wiping off dust and oil stainsfrom the frame.
(9) REINSTALLATION OF ORIGINAL PARTS
(a) Under cover (RH)-
07
- 20
005001
AC3572 SURGE TANK
VEHICLE WITH SURGE TANK ONLY
FRONT BUMPER
AC3571
SCREW
VEHICLE WITH SURGE TANK ONLY
FRONT FENDER LINER (LH) SCREWS AC3570
CLIPS
FRONT GRILLE AC3582
RADIATOR UPPER SUPPORTS (RH,LH)
� VEHICLE WITH SURGE TANK ONLY [(b)~(c)](b) Surge tank
(c) Screw
(d) Front fender liner (LH)
(e) Radiator upper supports (RH,LH)
(f) Front grille-
07
- 21
005001
FRONT
AC4374
AIR DUCT
AC4416
AIR CLEANER BOX LOWER COVER
FRONT
CAUTION
FRONT AC4417
VEHICLE HARNESS CLAMP
FRONT
AC4418
FILTER
(g) Air duct
(h) Air cleaner box lower cover
CAUTION
Make sure to be inserted the air duct into the aircleaner box lower cover.
(i) Vehicle harness clamp
(j) Filter
-
07
- 22
005001
VSV
FRONT
AIR CLEANER BOXUPPER COVER
VSV
HOOK
AC4419
AC4369
VEHICLE HARNESS
AIR CLEANER BOX UPPER COVER
AIR CLEANER HOSE
FRONT
AC4368
BATTERY
BATTERY TRAY
ENGINE COVER
AC3583
1ZZ-FE E/G MODEL ONLYRIB
(k) Reinstall the VSV to the air cleaner box upper cover.
(l) Air cleaner box upper cover
(m) Reconnect the vehicle harness to the air cleanerbox upper cover.(n) Reconnect the air cleaner hose to the air cleaner
box upper cover.
(o) Battery and battery tray
� 1ZZ-FE E/G MODEL ONLY [(p)]
(p) Engine coverTightening Torque
7.0 N•m (71 kgf•cm, 5.1 lbf•ft)
-
07
- 23 -
00500107
2. AFTER INSTALLATION
CAUTION
2-1.CHARGING REFRIGERANT (HFC-134a)
For additional information on charging refrigerant using the charging cylinder, refer to "GENERAL INFORMATION/AF-TER INSTALLATION: CHARGING REFRIGERANT (134a)".
CAUTION
2-2.RE-ADJUSTMENT OF COMPRESSOR BELT (1NZ/2NZ E/G MODEL ONLY)
To correct belt deflection caused by initial elongation, the air conditioning must be operated for at least 5 minutes before the final adjustment of the belt.
CAUTION
2-3.ADJUSTMENT OF ENGINE IDLING SPEED
CAUTION
Refer to the separate manual "GENERAL INFORMATION/AFTER INSTALLATION" for details on what to do after installation. (Document code: AOAMC-01*/Document part number: 988963-475*)
STANDARD AMOUNT OF REFRIGERANT 490 ± 30 g (1.08 ± 0.7 lbs)
Ensure to fill the refrigerant to the specified amount.
Belt deflection[at 98N(10kgf, 22lbf)force]
Belt tension[N (kgf, lbf)]
Vehicle equipped with 1NZ/2NZ E/G 11.0 - 13.0 mm(0.44 - 0.51 inch)
245 - 392 N(25 - 40 kgf, 55 - 88 lbf)
1. Excessive tension of belt may have an adverse effect on bearings, while excessive slackness can cause the belt to slip, make abnormal noise or shorten the belt life.
2. The belt deflection must be measured between the specified pulleys as indicated in this manual.3. The belt tension must be measured between the specified pulleys as indicated in this manual.4. The belt tension must be adjusted to the center of the specified belt tension range.
The engine revolution is controlled by a computer, therefore adjustment is not required. (when the air conditioning system is started, check whether idling revolution increases.)
3. AMPLIFIER� ALL EUROPEAN SPEC. AND 1NZ/2NZ-FE E/G MODEL (VEHICLE WITH HEATER)
- 24 -
00500107
� 1NZ/2NZ-FE E/G MODEL (VEHICLE WITHOUT HEATER)
- 25 -
00500107
� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL (VEHICLE WITH HEATER AND GENERALLY SPEC.)
- 26 -
00500107
� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL (VEHICLE WITHOUT HEATER AND GENERALLY SPEC.)
- 27 -
00500107
4. WIRING DIAGRAM� 1NZ/2NZ-FE E/G MODEL (VEHICLE WITH HEATER)
COMPRESSOR
MIDDLE EASTEXCEPT
Mg/CRELAY
IGRELAY
IG SW
12V
HEATERMAIN RELAY
BLOWERMOTOR
RH
LH
BLOWERRESISTOR
BLOWERRESISTOR
BLOWER SW RH A/C SW
TO RHEOSTAT
TO TAIL RELAY
AC3784
- 28 -
00500107
246108-404
ONLYMIDDLE EAST
COMPRESSOREFI ECUPRESSURE SW
A/C AMP
EVA.THERMISTOR
LH A/C SW
RESISTOR
FAN RELAY No.2
RADIATORFAN MOTOR
FAN RELAY No.1
AC3785
- 29 -
00500107
� 1NZ/2NZ-FE E/G MODEL (VEHICLE WITHOUT HEATER)
MIDOLE EASTEXCEPT
COMPRESSORMg/CRELAY
IGRELAY
IG SW
12V
HEATERMAIN RELAY
BLOWERMOTOR
RH
BLOWERRESISTOR
BLOWERRESISTOR
LH
BLOWER SW
TO GND
TO TAIL RELAY
VOLUME SW
AC3786
- 30 -
00500107
ONLYMIDDLE EAST
COMPRESSOREFI ECUPRESSURE SW
A/C AMP
EVA.THERMISTOR
RESISTOR
FAN RELAY No.2
RADIATORFAN MOTOR
FAN RELAY No.1
246108-406
AC3787
- 31 -
00500107
� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL (VEHICLE WITH HEATER)
COMPRESSORMg/CRELAY
IGRELAY
IG SW
HEATERMAIN RELAY
BLOWERMOTOR
BLOWERRESISTOR
BLOWERRESISTOR
LH
RH
BLOWER SW A/C SW
TO GND
TO TAIL RELAY
12V
AC3788
- 32 -
00500107
246108-647
EFI ECUPRESSURE SW
A/C AMP
EVA.THERMISTOR
RESISTOR
FAN RELAY No.2
RADIATORFAN MOTOR
FAN RELAY No.1
AC3789
- 33 -
00500107
� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL (VEHICLE WITHOUT HEATER)
IGRELAY
IG SW
HEATERMAIN RELAY
BLOWERMOTOR
BLOWERRESISTOR
12V
RH
LH
BLOWERRESISTOR
BLOWER SW
VOLUME SW
TO GND
TO TAIL RELAY
Mg/CRELAY
COMPRESSOR
MIDDLE EASTEXCEPT
AC3790
- 34 -
00500107
A/C AMP
EVA.THERMISTOR
RESISTOR
PRESSURE SW EFI ECU
FAN RELAY No.1
RADIATORFAN MOTOR
FAN RELAY No.2
ONLYMIDDLE EAST
COMPRESSOR
246108-407
AC3791
- 35 -
00500107
� ALL EUROPEAN SPEC.
COMPRESSORMg/CRELAY
IGRELAY
IG SW
12V
HEATERMAIN RELAY
BLOWERMOTOR
BLOWERRESISTOR
BLOWERRESISTOR
LH
RH
BLOWER SW A/C SW
TO GND
TO TAIL RELAY
AC4498
- 36 -
00500107
246108-711
EFI ECUPRESSURE SW
A/C AMP
EVA.THERMISTOR
RESISTOR
FAN RELAY No.2
RADIATORFAN MOTOR
FAN RELAY No.1
AC4499
- 37 -
00500107
- 38 -
00500107
DENSO CORPORATION
SERVICE DEPARTMENT
Kariya, Aichi, Japan
Frist Issue : AUGUST 2000
Second Issue : SEPTEMBER 2001
Publication No. : AAAMB-25A
Printed in Japan
AAAMB-25A988963-4561