A8€¦ · A8 Installation Packet Page 4 of 14 3430450000 E Leg and Foot Assembly 1 - Slide...

A8Installation Instructions

Pour des instructions en francias, appelar le 800-822-7653 Para instrucciones en enspanol, llame al 800-822-7653

3430450000 E

Tools NeededDrill

#2 Phillips Driver#3 Phillips Driver4mm Allen Driver

1/4” Socket or Driver Bit5/16” Socket or Driver Bit

3/8” Socket or Driver BitT20 Driver Bit

IndexA8 Parts Outline . . . . . . . . . . . . . . . . . . . . . . 2

Table Assembly . . . . . . . . . . . . . . . . . . . . . . . 3

Leg and Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Utility Bay End Caps . . . . . . . . . . . . . . . . . . . . . . . . . 3

Utility Bay Latch Rail . . . . . . . . . . . . . . . . . . . . . . . . . 5

Control Box and Height Adjustable Control . . . . . . . . 5

Utility Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Grommet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Wire Management . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Screen Assembly . . . . . . . . . . . . . . . . . . . . . 8

Screen Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Power Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Power Rail Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Optional Floor Anchor . . . . . . . . . . . . . . . . . . . . . . . 10

End of Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

“T”, “L”, and “X” Connections . . . . . . . . . . . . . . . . . . 11

Inline Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Electrical and Data . . . . . . . . . . . . . . . . . . . . . . . . . 12

Finishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Hardwire Power In-feed . . . . . . . . . . . . . . . . . . . . . . 13

Electrical Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

A8 Installation Packet

3430450000 E of 14

A8 Parts Outline

WorksurfaceWorksurface Bracket

Height Adjustable Column

Control BoxTable Foot

Utility Bay End CapUtility Bay End Cap

Latch Rail

Grommet

Utility BayPower Module

Dual Lock

Column Wire Manager

Energy Chain & Clip

Screen L-Bracket

Screen

Power Rail Lower Housing Power Rail Upper Housing

Power Rail Foot

Universal Connector Power Rail End Cap

Connector Bracket

Universal Connector Door Bracket

Port CoverPower Rail Snap Bushing

Height Adjustable Control

Screen Placeholder Bracket

Energy Chain BracketA


3430450000 E of 14

7 - Attach foot to leg column; each leg requires four (4) 4mm hex screws .

8 - Attach glides or casters . Glides thread directly into foot . Casters attach with four (4) 5/16” socket screws per caster . Slide glides adhere to standard glides .

Note: Casters cannot be installed on 24” tables with screen and utility bay .

6 - Attach end cap with 5/16” socket screws; each end cap requires two (2) screws .

Leg and Foot Assembly


3430450000 E of 14


1 - Slide worksurface bracket over motor in orientation shown .2 - Attach worksurface bracket with four (4) 4mm hex screws .

5 - Align leg assembly with locator holes in orientation shown Attach to worksurface with #3 Phillips screws; each leg requires ten (10) screws .

Align with locator holes

3 - Attach Energy Chain Clip(included with Energy Chain Model FDCLWMC) to Energy Chain Bracket with two(2) #8 flat head screws(included in hardware pack sent with Energy Chain Model)

4 - Align Energy Chain Bracket with worksurface bracket as shown . Bracket to be placed on leg that Column Wire Manager will be installed . Bracket placed on side near-est to back edge of worksurface .



3430450000 E of 14

Utility Bay Assembly

1 - Using locator holes as alignment, attach the latch rail with six (6) #3 drive Phillips screws as shown .

Note: The holes closest to the bend will align with the locator holes .

Note: The holes are slotted to allow for adjustment in Step 4 .

2 - Attach the control box with two (2) #2 drive Phillips screws, and attach cord clips with one (1) 1/4” socket screw per clip .

Note: The control box should be attached as close to either leg column as possible to avoid interfering with the utility bay compartment dividers .

Note: On 60” worksurfaces, the control box will rest inside either end compartment . Control box CANNOT be attached to worksurface .

5 - Align utility bay with locator holes and attach with nine (9) #3 drive Phillips screws .

Note: 48” and 54” tables will have one (1) compartment; all larger sizes will have three (3) compartments .

6 - Verify utility bay compartments are engaged with latch rail . Adjust the latch rail if needed .



3 - Attach the height adjustable control with two (2) #2 drive Phillips screws .

4 - Connect motors and height adjustable control to control box .


3430450000 E of 14

Grommet and Power Module

1 - Orient the grommet with the hinge toward the rear of the worksurface . Press grommet assembly into worksurface .

2 - Power modules come standard with Dual Lock . Place Dual Lock on the back of the power module and adhere to the back of the center utility bay . Please note that the set time for the VHB is 20 minutes for 50% strength, 24 hours for 90% strength, and 72 hours for 100% strength .

Note: Locate cord and reset button to notch in back of utility bay .

Align cord and reset button with notch in mounting rail

Align cord and reset button with notch in utility bay


3430450000 E of 14

is

SCALE 0.250SECTION COLUMN_MANAGER_2-COLUMN_MANAGER_2

1 - Route the wires through the utility bay end cap .Note: The wires can be routed through either the RH or LH side,

per furniture layout (RH exit shown) .

Wire Management

2 - Route the wires up through the top of the column wire manager, down the back of the column wire manager, and out the bottom of the column wire manager as shown . The image is a cutaway view .

Note: Top cap may be removed and reinstalled to ease assembly .

3 - Apply column wire manager mounting bracket via the preinstalled VHB tape to column where column wire manager is to be mounted . Arrow is to point up towards the worksurface when installed . Bracket to be flush with the top of the foot Ensure adhession by applying pressure to each strip of tape . Please note that the set time for the VHB is 20 minutes for 50% strength, 24 hours for 90% strength, and 72 hours for 100% strength .

5 - Ensure the energy chain is oriented such that the top links smooth sides face toward the back of the worksurface, as shown .

6 - Attach the energy chain to the column wire manager by snapping the two pegs on the energy chain over the two holes on the inside of the column wire manager .

7 - Attach the energy chain to the energy chain attachment bracket & clip assembly . The clip and chain assemble as shown to left .

8 - Press cords into the open face of the energy chain links .Arrows indicate connection orientation

4 - Height Adjustable legs will need to be raised for Column Wire Manager Attachment . Slide column wire manager down the column wire manager mounting bracket until fully seated with the bottom of the column wire manager resting on the foot .


3430450000 E of 14

Screen Attachment

Step 1

Step 2

1 - Set screen on clean flat working surface.

2a - Remove first placeholder bracket.2b - Replace with first L-bracket, using the

same holes and screws . 2c - Remove second placeholder bracket .2d - Replace with second L-bracket, using the

same holes and screws .

CAUTIONDo not cut new holes in fabric; useholes from placeholder bracket.

2 - Remove placeholder brackets and replace with L-brackets . Use a #3 Phillips drive for steps 2a-2d .

2a

2d2c

2b

Align this edgewith edge ofworksurface

Align withlocator holes

Step 33 - Using back edge of worksurface or

locator holes for alignment, attach L-brackets to worksurface with six (6) #3 drive Phillips screws .

Placeholder bracket L-bracket


3430450000 E of 14

Step 4Screen Attachment

4a - Ensure seams are located on edges, as shown .4b - Flatten out wrinkles from handling .4c - Ensure fabric tension is even throughout the screen . Check that bridge over wing is consistent .

4 - Smooth out fabric with clean hands .

Seams

Wrinkles

Bridging

üû

Note: There may be slight engineered interference with square corner worksurfaces and bridge .


3430450000 E of 14

Power Rail

Foot Attachment1 - Slide foot into the slot in the orientation

shown .2 - Select a desired height .Note: Each foot provides 2 inches of leveling .3 - Attach the feet with two (2) 3/8” socket

screws .

End of Rail1 - Remove knockouts where necessary . De-burr

cutouts and install 1 .5” snap bushing .2 - Align the hole in the end cap with the center

hole on the lower housing .3 - Attach with one (1) T20 drive screw .

Optional: Floor Anchor1 - Align the configured product in the desired

installation location .2 - Using the pass-through hole in the lower

housing and the power rail foot, mark the location for anchoring .

3 - Move product and drill surface if necessary, then realign the product and install hardware (hardware not supplied) .


3430450000 E of 14

Inline Connection1 - Align the lower housings end to end .2 - Align the connector bracket so the four holes

in the bracket line up with the four holes in the lower housings .

3 - Install four (4) T20 drive screws .

“T”, “L”, and “X” Connections1 - Place the universal connector assembly

between the lower rail housings that are to be connected .

2 - Align the connector brackets to the mounting holes in the lower housing and the universal connector . Attach the connector bracket with four (4) T20 drive screws .

Note: Connector bracket ships with power rail .3 - Repeat Step 2 for each additional power

rail .

4 - All sides of the universal connector that do not have a power rail attached to it must have a door . Center and align the door with the “TOP” embossed tab on top .

5 - Place the connector bracket lip over the bottom tab and align the two holes with the two holes on the bottom of the universal connector .

6 - Attach with two (2) T20 drive screws .

Power Rail


3430450000 E of 14

3 - Cap all universal connectors . Align the four posts of the top cover over the four holes in the universal connector assembly and press cover into place, ensuring the top tabs of the door are engaged with the edge of the top cover . Press until top cover is fully seated .

Power Rail

Electrical/Data1 - Insert duplexes into the power harness .2 - Slide the power blocks into the electrical brackets .Note: The upper housings must have at least one duplex .3 - Connect the power harnesses together and to in-feed as

necessary .4 - Snap data faceplates into cutouts as specified.5 - Secure the infeed to the foot with a ziptie as shown .Note: Data cannot be installed back-to-back .

Finishing1 - Align the top rib of the lower housing with the groove

in the upper housing . Rotate the upper housing downward and snap the two housings together .

2 - Install the port covers into any unused cutout . All cutouts must be filled with either a duplex, data faceplate, or port cover .

SCALE 0.500


3430450000 E of 14

Power Rail with New York Infeed

A8 Beam End InfeedNew York Junction Box

24” wide pass through with power block

Power Whip Entry

A8 Beam End Infeed1 - Same kit regardless of beam length . Order 4 circuit or 3 circuit depending on requirements2 - Slide Beam End Cap on Power Whip before wiring to New York Junction Box3 - Install 24” W Pass Through with power block on opposite side of Power Whip entry . Block side to

be to the inside of beam .4 - Connect New York Junction Box to Power block on Pass Through. Junction box may float inside

beam or electrical mounting bracket may be moved to hard mount .5 - Install Power Whip to New York Junction Box . Secure the infeed to the foot with a ziptie as shown

on page 12 .6 - All additional beams will utilize standard ElectricalNote: The New York Junction Box will block usage of power and data ports at the location it is

installed .

Beam width specific Pass Through with Power block

New York Junction BoxPower Whip Entry

A8 Beam Middle Infeed

A8 Beam Middle Infeed1 - Different Kit based on beam length. Order 4 circuit or 3 circuit depending on requirements2 - Install New York Junction Box location where Power Whip will enter .3 - Connect tail from New York Junction box to electrical in adjacent beam .4 - Pass Through must connect at adjacent beam . Then must be routed back past the New York

Junction box and the power block may then clip in place at opposite side of power entry .5 - All additional beams will utilize standard ElectricalNote: The New York Junction Box will block usage of power and data ports at the location it is

installed .


Improperly installed electrical components can fail resulting in personal injury and/or property damage.Connection to a power source should be performed by a licensed electrician. The previous connection and the quantity of receptacles used for a given circuit must both be in compliance with all national and local electrical codes. To prevent personal injury ensure all power sources are disconnected during installation.

W A R N I N G

3430450000 EPages 14 of 14

88 | Stride & Terrace – 3/2013

Fra

me

s –

Tile

s sp

ec

sFr

am

es

– Ti

les

pr

icin

ge

lec

Tric

al

Wo

rk

sur

Fac

es

Wo

od

sTo

ra

ge

me

Tal

ov

er

he

ad

sB

en

ch

ing

sT

rid

e

Flexconnect™ Electrical System OptionsThe four-circuit, eight-wire electrical system is widely specified and trusted by hundreds of thousands of end-users. This proven system deliversfourcircuitsforeverypowerinfeedineithera3+1or2+2configuration. The isolated/dedicated circuits are ideal for sensitive computing equipment, while the common circuits are suitable for faxes, copiers,tasklightsandotherperipherals.Boththe3+1and2+2systems use the same pre-wired components, making it easy to adjust as electrical needs change.

You can also choose a three-circuit, eight-wire system that has a dedicated neutral for every hot circuit. The three-circuit components havemodelnumberswithan“A”suffix.

Electrical & Data Stride® — Working with Electrical & DataTo Order:1. Determine which electrical system you will

use after consulting your electrician and computer support personnel:•TheFour-circuitsystem

(4-Hot/2-Neutral/2-Ground)– 3+1option– 2+2option

•TheThree-circuitsystem(3-Hot/3-Neutral/2-Ground)

•TheEight-circuitsystem(back-to-backfour-circuit systems)

2. Determine location, quantity and circuit of duplexes.

3. Determine the appropriate choice and use of Isolated, Isolated/Dedicated and Separate Neutrals circuits.

4. Specify appropriate Power Harnesses* and Pass-Thru Cables.*

5. Determine the location, quantity and type of Power In-feeds needed.

*SelectPowerHarnessmodels(8712XX),Pass-ThruCables(8710XX)andPass-ThruHarness(8711XX)withthelasttwodigitscorresponding with the panel width into which the component is to be positioned. The initial cable length can be stretched approximately 3" to transverse TEE, CROSS, ELL and Extended Straight Connectors.

GRAYWHITEGRN/YLWGRN/BAREPINKBLUEREDBLACK

DUPLEX RECEPTACLECIRCUIT 1

12 GA10 GA12 GA12 GA12 GA12 GA12 GA12 GA

NEUTRAL - 2NEUTRAL - 1ISOLATEDGROUNDHOT - 4HOT - 3HOT - 2HOT - 1

CIRCUIT 2 CIRCUIT 3

CIRCUIT 4ISOLATED/DEDICATED

GRAYWHITEGRN/YLWGRN/BAREPINKBLUEREDBLACK

DUPLEX RECEPTACLECIRCUIT 1

12 GA10 GA12 GA12 GA12 GA12 GA12 GA12 GA

NEUTRAL - 2NEUTRAL - 1ISOLATEDGROUNDHOT - 4HOT - 3HOT - 2HOT - 1

CIRCUIT 2CIRCUIT 3ISOLATED

CIRCUIT 4ISOLATED

Four‑circuit, 3 + 1 Receptacle Option

Four‑circuit, 2 + 2 Receptacle Option

The3+1optionistheelectricalstandardusedonAllsteelsystemsfor many years in most installations. This wiring option provides three utility circuits plus an isolated/dedicated circuit for more sensitive equipment. Circuit 2 (one of the 3 common circuits sharing a neutral wire) cannot be used with single-phase building electrical supply.

The2+2optionisawiringoptionthatprovidestwoutilitycircuits and two isolated circuits for more extensive computer usage applications.

GSA Reference Page

A8€¦ · A8 Installation Packet Page 4 of 14 3430450000 E Leg and Foot Assembly 1 - Slide...

Documents

Transcript of A8€¦ · A8 Installation Packet Page 4 of 14 3430450000 E Leg and Foot Assembly 1 - Slide...