A SSEMBLY INSTRUCTIONS S1 - LaCantina Doors · A SSEMBLY INSTRUCTIONS REMOVE FINAL PACKAGING...
2
FIXING OFF THE SCREEN INITIAL UNPACKING ATTACH HEAD APPLY TENSION ATTACH SILL STAND UP & SQUARE UP FRAME IN OPENING S1 ASSEMBLY INSTRUCTIONS REMOVE FINAL PACKAGING OPERATE SCREEN LATERAL ADJUSTMENT IF NECESSARY Package 1 of 2 instruction sheet and DVD Package 2 of 2 Ensure jamb tongues are facing each other S1 Screen S1 SCREENING SYSTEM PACK AG E 2 CONT AINS: • Head • Head Cover • Sill • Sill Cover • Installation Ki t • Jamb Cover x 2 • Sill Gap Seal • Stile Covers PACKAGE 2 OF 2 S1 SCREENING SYSTEM PACK AG E 1 CONT AINS: • Instructions • Installation DV D • 2 x Jambs containing either a. Single Screen (1 Sc reen and 1 Stil e) b. Double Screen (2 Sc reens and 2 Stiles ) PACKAGE 1 OF 2 S1 KIT Optional mounting kit No fixings to be placed into jambs. Use double sided tape only Move top and bottom springs to hook over painted yellow posts for pre-tension Cable Sheath Screen Clips Ensure wheel at top of stile is hung on the track Cable Clamp MUST BE REMOVED BEFORE OPERATION x3 Operate screen fully three times Close screen. Check stile is parallel against the jamb If stile is not parallel to jamb, retract screen and turn adjustment screw Repeat steps A, B and C until stile and jamb are parallel A. B. C. Fixing the Head Fixing the Sill SCREW FIXINGS IN RED AREA ONLY PROVIDE TEMPORARY SUPPORTS TO BOTH JAMBS TO PREVENT SCREEN FALLING Head fixing option using 90 degree driver (Centor part #S190DA) 5mm (3/16”) 3mm (1/8”) 3mm (1/8”) Distributed by:
Transcript of A SSEMBLY INSTRUCTIONS S1 - LaCantina Doors · A SSEMBLY INSTRUCTIONS REMOVE FINAL PACKAGING...
FIXING OFF THE SCREEN
INITIAL UNPACKING
ATTACH HEAD
APPLY TENSION
ATTACH SILL
STAND UP & SQUARE UP FRAME IN OPENING
S1 ASSEMBLY INSTRUCTIONS
REMOVE FINAL PACKAGING
OPERATE SCREEN LATERAL ADJUSTMENT IF NECESSARY
Package 1 of 2
instruction sheetand DVD
Package 2 of 2
Ensure jambtongues are facingeach other
S1 Screen
S1SCREENING SYSTEM
PACK AG E 2 CONT AINS:
• Head • Head Cover
• Sill • Sill Cover
• Installation Ki t • Jamb Cover x 2
• Sill Gap Seal • Stile Covers
PACKAGE 2 OF 2
S1SCREENING SYSTEM
PACK AG E 1 CONT AINS:
• Instructions
• Installation DV D
• 2 x Jambs containing either
a. Single Screen (1 Sc reen and 1 Stil e)
b. Double Screen (2 Sc reens and 2 Stiles )
PACKAGE 1 OF 2
S1 KIT
Optionalmounting kit
No �xings to be placed into jambs.Use double sided tape only
Move top and bottom springs to hook over painted yellow posts for pre-tension
Cable Sheath
Screen Clips
Ensure wheel at top of stile is hungon the track
Cable Clamp
MUST BE REMOVED BEFORE OPERATION
x3
Operate screen fully three times Close screen. Check stile is parallel against the jamb If stile is not parallel to jamb, retract screen and turn adjustment screw
Repeat steps A, B and C until stile and jamb are parallel
A. B. C.
Fixing the Head
Fixing the Sill
SCREW FIXINGS IN RED AREA ONLYPROVIDE TEMPORARY SUPPORTS TO BOTH
JAMBS TO PREVENT SCREEN FALLING
Head �xing optionusing 90 degree driver(Centor part #S190DA)
5mm (3/16”)
3mm(1/8”)
3mm(1/8”)
Distributed by:
FITTING COVERS SILL COVER
DOOR STOP (DOUBLE SCREEN ONLY)
HEAD/JAMB COVER REMOVAL
SILL COVER REMOVAL
HEAD COVERS
JAMB COVERSJAMB STOP (SINGLE SCREEN ONLY)
Fit after test and adjustmentto prevent movement andexclude construction debris
STILE COVERS
SILL GAP SEAL (OPTIONAL)
INSTRN
S-S1 v02
