a Nexans company · of CENELEC EN 50181, IEC 60071 and IEC 60137. 6/10 (12) kV 6.35/11 (12) kV...
Transcript of a Nexans company · of CENELEC EN 50181, IEC 60071 and IEC 60137. 6/10 (12) kV 6.35/11 (12) kV...
Catalogue 2011
a Nexans company
1
06/2
011
While every care is taken to ensure that the information contained in this publication is correct, no legal responsibility can be accepted for any inaccuracy. Nexans Network Solutions N.V. - Div. Euromold reserves the right to alter or modify the characteristics of its products described in this catalogue as standards and technology evolve.
EUROMOLDEuromold is the leading European specialised designer, manufacturer and distributor of prefabricated cable accessories for medium voltage energy distribution. Euromold provides a complete range of accessories for underground cables: premoulded EPDM rubber connectors for cables and epoxy bushings for transformers and switchgear, as well as a large range of cold-shrinkable terminations and joints from 12 to 42 kV.Euromold is also the manufacturer of electrical components for the high voltage accessories of the Nexans group.
ISO 9001 CertificateSince 1992, Euromold’s commitment to quality is demonstrated by its ISO 9001 certification.
Laboratory accreditationSince June 2000, Euromold’s independent ELAB laboratory obtained the BELAC accreditation no.144-TEST conform with the European standards for laboratories ISO 17025 for electrical testing of low and medium voltage cable accessories according to the international standards EN 50393, IEC 60502-4, IEC 61442 and HD 629.
International standardsAll our products meet the International standards like CENELEC HD 629.1, CENELEC EN 50180, IEC 60137, IEC 60502-4… or country speci-fications. Official certificates, CESI, KEMA, ATEX… prove the conformity of our products. Long duration tests of existing or new products are con-tinuously performed in our test fields.
Nexans Network SolutionsDiv. Euromold
COMPANY PRESENTATION
2
08/2
011
EQUIPMENT BUSHINGS
Table of contents180AR-1 - interface A1 equipment bushing180AR-2 - interface A1 equipment bushing180AR-3 - interface A1 equipment bushing250SFR-P - interface A1 equipment bushing180A-24P-O - interface A1 in-air bushing400T1 - interface B2 equipment bushing400AR-1 - interface B2 equipment bushing400AR-2 - interface B2 equipment bushing400AR-8 - interface B1 equipment bushing400SFR-P - interface B2 equipment bushing400AR-3 - interface C1 equipment bushing400AR-4 - interface C2 equipment bushing400AR-5 - interface C2 equipment bushing400AR-6 - interface C1 equipment bushing400SFR-B - interface C1 & C2 equipment bushing400A-24B - interface C1 in-air bushing670AR-2 - interface D2 equipment bushing900AR-1 - interface F3 equipment bushing900AR-2 - interface F2 equipment bushing900AR-3 - interface F1 equipment bushing900AR-4 - interface F1 equipment bushing
3 08/2
011
48 0-0.2
Dia. 48.5±0.2
Dia. 32.5±0.2
Dia. forpin 7.9+0.02
- 0.05
Dia. 31+0.1 - 0.3
9min
DIMENSIONS & RATINGS OF EQUIPMENT BUSHINGS
Interface type Contact typeCurrent rating
(A)RMS symm. (kA) Peak asymm.
(kA)1 sec. 2 sec. 3 sec.
A1B1B2C1C2D1D2F1F2F3
Pin and socketPin and socketPin and socket
BoltedBoltedBoltedBoltedBoltedBoltedBolted
2502504006301250800125025006301250
12.512.516.028.075.050.075.0
-28.075.0
9.09.011.319.753.035.353.0
-19.753.0
7.57.59.216.143.328.843.3
-16.143.3
31314070
>150125
>150-
70>150
Short circuit ratings
DimensionsThese diagrams show the dimensions of the interfaces of equipment bushings according to CENELEC standards EN 50180:2010 and EN 50181:2010.
Interface F1, F2 & F3Interface D1 & D2
81±0.2
Dia. 76.2±0.2
14.8min
29min
Dia. 39.9±0.2
Dia. 32nominal
Dia. 52.1±0.2
0-0.51.5
M16 x 2 - 6H
Interface A1 Interface B1 & B2
90±0.2
Dia. 46±0.2
Dia. 56±0.2
Dia. 70±0.2
40min
Dia. forpin 14 0
-0.04
11min
Interface C1 & C2
90±0.2
Dia. 46±0.2
Dia. 56±0.2
Dia. 70±0.2
0-0.51.5M16 x 2 - 6H
29min
11min
Dia. 22 min for C1Dia. 32 nominal for C2
In mm.
110.5±0.2
29min
Dia. 64±0.2
Dia. 86.8±0.2
0-0.51.5
M16 x 2 - 6H
Dia. 50 min for F1Dia. 22 nominal for F2Dia. 32 nominal for F3
4
08/2
011
Up to 24 kV - 250 A
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
Dimensions (mm)
A B
180AR-1
K180AR-1
180AR-2
K180AR-2
180AR-3
K180AR-3
12
24
12
24
12
24
250
250
250
250
250
250
222
222
284
284
171
171
106
106
168
168
55
55
180AR-1 /180AR-2 /180AR-3INTERFACE A1
EQUIPMENT BUSHINGS
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors...
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV
Design• The equipment bushings are
moulded epoxy insulated parts in accordance with CENELEC EN 50180.
The 180AR-2 bushing has a length B outside this standard.
• The standard bushings, (K)180AR-1 /-2 /-3, are equipped with 6 tabs for the bail restraint.
• The (K)180AR-1-G and (K)180AR-3-G are equipped
with 4 tabs and 2 threaded inserts M6 (-G version).
Technical characteristics Each bushing is tested for AC withstand and partial discharge prior to leaving the factory.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings are supplied with an earth jumper (/J) or an earth plate (/GS). This earth connection must be specified when ordering.E.g. K180AR-1/J.
Specifications and standardsThe plug-in type equipment bushings 180AR-… meet the requirements of CENELEC EN 50180 and IEC 60137.
Type 180AR-1-G /-3-G Type 180AR-1 /-2 /-3
In mm.
11
B
A
28
8
19
Dia. 110
Dia. 75
Minimum oil level:- 12 kV: 40 mm- 24 kV: 50 mm
M10
M6
Dia.16
5
FIXINGS FOR EQUIPMENT BUSHINGS
180AR-1/J 180AR-1-G/J 180AR-2/J 180AR-3/J and 180AR-3-G/J Bushings
180AR-1/GS 180AR-1-G/GS 180AR-2/GS 180AR-3/GS and 180AR-3-G/GS Bushings
Bushing clamping kitTo order the bushing clamping kit, according to NFC 52-053 standards, simply specify KBCNF1-200.Contents: - 3 x claw clamp NF200 - 1 x sealing gasket.
Bushing clamping kitTo order the bushing clamping kit, according to DIN 42 538 standards, simply specify: KBCD-200.Contents: - 1 x fixing flange A - 4 x stud clamp E - 1 x sealing gasket.
Fixing dimensions standards NF C 52-053French standards.
Fixing dimensions standards DIN 42 538German standards.
In mm.
M10
4 fixingstuds
55
Dia. 78
Dia. 123
30
M8 orM10
3 fixingstuds
52
Dia. 78
Dia. 126
30
earth jumper
A DIN 42 538 fixing flange
earth plate
sealing gasket
equipment
fixing studs
bushing interface
E DIN 42 538stud clamp
NF C 52-053clamp
tabs for bail restraint
equipment connection
6
08/2
011
Up to 24 kV - 250 A
250SFR-PINTERFACE A1
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with SF6 gas.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV
DesignThe equipment bushing is a moulded epoxy insulated part with a connector interface in accordance with CENELEC EN 50180. The 250SFR-P bushing has a shank outside this standard, adapted to use in SF6 gas.
Technical characteristics Each bushing is tested forAC withstand and partialdischarge prior to leaving thefactory.
Ordering instructionsTo order the equipment bushing, simply specify the type.
Specifications and standardsThe plug-in type equipment bushings 250SFR-P meet the requirements of CENELEC EN 50180 and IEC 60137.
In mm.
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
250SFR-P
K250SFR-P
12
24
250
250
Dia. 70
95
31
174
Dia. 109
M10
Dia. 20
Dia. 70
Dia. 48.5
7
FIXINGS FOR EQUIPMENT BUSHINGS
250SFR-P Bushing for gas insulated switchgear
In mm.
equipment
MOUNTED
6 fixingscrews
M6sealingO-ringgasket
equipmentconnectionbushing
interface earthconnection
M4
30°
UNMOUNTED
60°
60°60°
Dia. 91.5Dia. 103.1
83
M6
earthconnectionM4
8
08/2
011
180A-24P-OINTERFACE A1
IN-AIR BUSHING
Up to 24 kV - 250 AApplicationFor use in equipment insulated with air, typically for dry type transformers, motors, switchgear, capacitors...
Technical characteristics Each bushing is tested forAC withstand and partialdischarge prior to leaving thefactory.
Specifications and standardsThe plug-in type equipment bushings 180A-24P-O are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50181, IEC 60071 and IEC 60137.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
Creepage distanceA-B
(mm)
180A-24P-O
180A-24P-O
12
24
250
250
630
630
Ordering instructionsTo order the equipment bushing, specify the type.The bushings are supplied with an earth jumper.To include the ring clamp, add:• /B, if per British standards• /D, if per German standards• /F, if per French standards.E.g. 180A-24P-O/F.
In mm.
59
Dia. 80
351
250
M10
Dia. 70
Dia. 110
20
20
B
A
Dia.16
9
180A-24P-O In-air bushing
In mm.
FIXINGS FOR EQUIPMENT BUSHINGS
M10
4 fixingstuds
2055
Dia. 123
Dia. 82
3 fixingstuds
2052
Dia. 126
Dia. 82
M10
Fixing dimensions standards NF C 52-053French standards.
Fixing dimensions standards DIN 42 538German standards.
10
Dia.12
Type BCA-B : BS 2562 British standardsType BCA-D : DIN 42 538 German standards
4
F
120°
120°
Type BCA-F : NFC 52-053 French standards
fixing studs andnuts M10
bushing interface
earth jumper
equipment
gasket
equipmentconnection
tabs for bailrestraint
fixing flangeBCA-B orBCA-D
fixing flangeBCA-F
Dia. 94.5
Dia. 111
BS 2562 stand.: 120DIN 42 538 stand.: 123
Dia. 150Dia. 150
10
Dia.124
Dia. 94.5
Dia. 111
126
10
08/2
011
Up to 36 kV - 400 A
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
Dimensions (mm)
A B C D E Dia. F Dia. G Dia. H
400T1K400T1M400T1400AR-1
K400AR-1M400AR-1400AR-2
K400AR-2M400AR-2
122436122436122436
400400400400400400400400400
310310310380380380329329329
144144144213213213138138138
303030303030363636
M12M12M12M12M12M12M16M16M16
222222222222404040
888888747474100100100
128128128128128128150150150
161616161616303030
400T1 /400AR-1 /400AR-2INTERFACE B2
EQUIPMENT BUSHINGS
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors... 6/10 (12) kV
6.35/11 (12) kV8.7/15 (17.5) kV
12/20 (24) kV12.7/22 (24) kV
18/30 (36) kV19/33 (36) kV
Technical characteristics Each bushing is tested forAC withstand and partialdischarge prior to leaving thefactory.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings are supplied with an earth jumper (/J) or an earth plate (/GS). This earth connection must be specified when ordering.E.g. K400AR-1/J.
Specifications and standardsThe plug-in type equipment bushings are moulded epoxy insulated parts and meet the requirements of IEC 60137. The (K)(M)400T1 also meets CENELEC EN 50180 .
In mm.
Minimum oil level:- 12 kV: 40 mm- 24 kV: 50 mm- 36 kV: 75 mm
E
Dia. G
133
B
A
Dia. F
Dia. 70D
10
C
Dia.H
11
FIXINGS FOR EQUIPMENT BUSHINGS
In mm.
400AR-1/J and 400T1/J Bushings
400AR-2/GS Bushing
Bushing clamping kitTo order the bushing clamping kit, according to NFC 52-053 standards, simply specify KBCNF-400 (for bushing type 400AR-2).Contents: - 4 x claw clamp NF400 - 1 x sealing gasket.
Fixing dimensions standards NF C 52-053French standards.
Fixing dimensions standards DIN 42 538German standards.
Dia. 105Dia. 171
6030
6 fixingstuds
M10M10 or M12
Dia. 105Dia. 171
50 to 7025
4 fixingstuds
55
Dia. 140Dia. 90
30
M10
6 fixingstuds
Fixing dimensions
Bushing clamping kitTo order the bushing clamping kit, simply specify: KBCDS-400B. Contents: - 1 x fixing flange - 6 x stud clamp F - 1 x sealing gasket.
400AR-2/J Bushing
bushing interface
fixing studs
equipmentconnection
sealing gasket
earthjumper
F DIN 42 538stud clamp
fixing flange
NF C 52-053claw clamp
equipment
earthplate
tabs for thebail restraint
fixing flangeB DIN 42 538
E DIN 42 538stud clamp
bushinginterface
fixing studs
equipment
sealing gasket
equipmentconnection
tabs for thebail restraint
earthjumper
Bushing clamping kitTo order the bushing clamping kit, according to DIN 42 538 standards, simply specify KBCD-400B.Contents: - 1 x fixing flange B - 6 x stud clamp E - 1 x sealing gasket.
12
08/2
011
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
400AR-8
K400AR-8
M400AR-8
12
24
36
250
250
250
Up to 36 kV - 250 A
400AR-8INTERFACE B1
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors...
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
Specifications and standardsThe plug-in type equipment bushings 400AR-8 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 60137.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings can be supplied with an earth jumper (/J).E.g. M400AR-8/J.
In mm.
6/10 (12) kV6,35/11 (12) kV
8,7/15 (17,5) kV12/20 (24) kV
12,7/22 (24) kV18/30 (36) kV18/33 (36) kV
80
231.528
Dia. 74
Dia. 110
20
Minimum oil level:- 12 kV: 40 mm- 24 kV: 50 mm- 36 kV: 75 mm
M10
8.5Dia.20
13
In mm.
FIXINGS FOR EQUIPMENT BUSHINGS
400AR-8/J Bushing
55
M10
Dia. 78
Dia. 123
25
4 fixingstuds
Fixing dimensions standards DIN 42 538German standards.
Bushing clamping kitTo order the bushing clamp-ing kit, according to DIN 42 538 standards, simply specify: KBCD-200.Contents: - 1 x fixing flange A - 4 x stud clamp E - 1 x sealing gasket.
4 x fixing stud M10
A DIN 42 538fixing flange
E DIN 42 538stud clamp
equipment
tabs for thebail restraint
bushing interface
sealing gasket
equipmentconnection
earth jumper
14
08/2
011
Up to 36 kV - 400 A
400SFR-PINTERFACE B2
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with SF6 gas.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV18/30 (36) kV19/33 (36) KV
DesignThe equipment bushing is a moulded epoxy insulated part with a connector interface in accordance with CENELEC EN 50180. The 400SFR-P bushing has a shank outside this standard, adapted for use in SF6 gas.
Technical characteristics Each bushing is tested forAC withstand and partialdischarge prior to leaving thefactory.
Ordering instructionsTo order the equipment bushing, simply specify the type.
Specifications and standardsThe plug-in type equipment bushing 400SFR-P meets the requirements of CENELEC EN 50180 and IEC 60137.
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
400SFR-P
K400SFR-P
M400SFR-P
12
24
36
400
400
400
Dia. 70
95
33
218
Dia. 109
Dia. 25
Dia. 70
M12
In mm.
15
FIXINGS FOR EQUIPMENT BUSHINGS
400SFR-P Bushing for gas insulated switchgear
In mm.
MOUNTED
equipment
sealingO-ringgasket
equipmentconnection
bushinginterface 6 fixing
screwsM6
earthconnection
M4
30°
UNMOUNTED
60°
60°60°
Dia. 91.5Dia. 103.1
83
M6
earthconnectionM4
16
08/2
011
Up to 36 kV - 630 A
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
400AR-3
K400AR-3
M400AR-3
12
24
36
630
630
630
400AR-3INTERFACE C1
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors...
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
Specifications and standardsThe bolted type equipment bushings 400AR-3 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 60137.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings can be supplied with an earth jumper (/J).E.g. M400AR-3/J.For use in potentially explosive atmospheres (for 12 kV max), order: 400AR-3/ATEX. Minimum oil level:
- 12 kV: 40 mm- 24 kV: 50 mm- 36 kV: 75 mm
40
Dia. 128
133
144
330
Dia. 88
Dia.25
Dia. 70M16
10
30
In mm.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV18/30 (36) kV19/33 (36) kV
17
In mm.
FIXINGS FOR EQUIPMENT BUSHINGS
400AR-3/J Bushing
Fixing dimensions standards DIN 42 538German standards.
M10
55
Dia. 140Dia. 90
25
6 fixingstuds
equipmentconnection
fixing studs
bushing interface
equipment
sealing gasket
fixing flangeB DIN 42 538
E DIN 42 538stud clamp
earth jumper
Bushing clamping kitTo order the bushing clamping kit, according to DIN 42 538 standards, simply specify KBCD-400B.Contents: - 1 x fixing flange B - 6 x stud clamp E - 1 x sealing gasket.
18
08/2
011
Up to 36 kV - 1250 A
400AR-4INTERFACE C2
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors... 6/10 (12) kV
6.35/11 (12) kV8.7/15 (17.5) kV
12/20 (24) kV12.7/22 (24) kV
18/30 (36) kV18/33 (36) kV
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
Specifications and standardsThe bolted type equipment bushings 400AR-4 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 60137.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings can be supplied with an earth jumper (/J) or an earth plate (/GS). This earth connection must be specified when ordering.E.g. M400AR-4/GS.
In mm.
40
10
138
329
Minimum oil level:- 12 kV: 40 mm- 24 kV: 50 mm- 36 kV: 75 mm
36
139
Dia. 150Dia. 100Dia. 70
M16
Dia. 32
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
400AR-4K400AR-4M400AR-4
122436
125012501250
19
FIXINGS FOR EQUIPMENT BUSHINGS
400AR-4/GS Bushing
Bushing clamping kitTo order the bushing clamping kit, according to NFC 52-053standards, simply specify KBCNF-400.Contents: - 4 x claw clamp NF400 - 1 x sealing gasket.
In mm.
Fixing dimensions standards NF C 52-053French standards.
400AR-4/J Bushing
NF C 52-053claw clamp
earth plate
bushing interface
fixing studs
equipment
equipmentconnection
sealing gasket
earth jumper
F DIN 42 538stud clamp
fixing flange
Bushing clamping kitTo order the bushing clamping kit with DIN style fixing flange, simply specify KBCDS-400.Contents: - 1 x fixing flange DIN style - 6 x stud clamp F DIN 42 538 - 1 x sealing gasket.
Fixing dimensions
Dia. 105Dia. 171
6030
6 fixingstuds
M10M10 or
M12
Dia. 105Dia. 171
50 to70 25
4 fixingstuds
20
08/2
011
Up to 36 kV - 1250 A
400AR-5INTERFACE C2
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors...
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV18/30 (36) kV
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings can be supplied with an earth jumper (/J) or an earth plate (/GS). This earth connection must be specified when ordering.E.g. M400AR-5/GS.
In mm.
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
400AR-5K400AR-5M400AR-5
122436
125012501250
32
72
245
Minimum oil level:- 12 kV: 40 mm- 24 kV: 50 mm- 36 kV: 70 mm
36
139
Dia. 150Dia. 76
M16
Dia. 32
Specifications and standardsThe bolted type equipment bushings 400AR-5 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 60137.
21
FIXINGS FOR EQUIPMENT BUSHINGS
400AR-5/GS Bushing
In mm.
NF C 52-053claw clamp
earth plate
bushing interface
fixing studs
equipment
equipmentconnection
sealing gasket
earth jumper
F DIN 42 538stud clamp
fixing flange
Bushing clamping kitTo order the bushing clamping kit, according to NFC 52-053standards, simply specify KBCNF-400.Contents: - 4 x claw clamp NF400 - 1 x sealing gasket.
Fixing dimensions standards NF C 52-053French standards.
Bushing clamping kitTo order the bushing clamping kit with DIN style fixing flange, simply specify KBCDS-400.Contents: - 1 x fixing flange DIN style - 6 x stud clamp F DIN 42 538 - 1 x sealing gasket.
Fixing dimensions
Dia. 105Dia. 171
6030
6 fixingstuds
M10M10 or
M12
Dia. 105Dia. 171
50 to70 25
4 fixingstuds
400AR-5/J Bushing
22
08/2
011
Up to 36 kV - 630 A
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
400AR-6
K400AR-6
M400AR-6
12
24
36
630
630
630
400AR-6INTERFACE C1
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors... 6/10 (12) kV
6.35/11 (12) kV8.7/15 (17.5) kV
12/20 (24) kV12.7/22 (24) kV
18/30 (36) kV19/33 (36) kV
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings can be supplied with an earth jumper (/J). This earth connection must be specified when ordering.E.g. M400AR-6/J.
In mm.
Specifications and standardsThe bolted type equipment bushings 400AR-6 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 60137.
40
Dia. 128Dia. 74Dia. 70
10
213
398
Minimum oil level:- 12 kV: 40 mm- 24 kV: 50 mm- 36 kV: 75 mm
30
133
Dia.25
M16
23
FIXINGS FOR EQUIPMENT BUSHINGS
400AR-6/J Bushing
In mm.
Fixing dimensions standards DIN 42 538German standards.
M10
55
Dia. 140Dia. 80
25
6 fixingstuds
equipmentconnection
fixing studs
bushing interface
equipment
sealing gasket
fixing flangeB DIN 42 538
E DIN 42 538stud clamp
earth jumper
Bushing clamping kitTo order the bushing clamping kit, according to DIN 42 538 standards, simply specify KBCD-400B.Contents: - 1 x fixing flange B - 6 x stud clamp E - 1 x sealing gasket.
24
08/2
011
Up to 36 kV630 A & 1250 A
400SFR-BINTERFACE C1 & C2
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with SF6 gas.
DesignThe equipment bushing is a moulded epoxy insulated part with a connector interface in accordance with CENELEC EN 50180. The 400SFR-B bushing has a shank outside this standard, adapted to use in SF6 gas.
Technical characteristics Each bushing is tested forAC withstand and partialdischarge prior to leaving thefactory.
Ordering instructionsTo order the equipment bushing, simply specify the type.
Specifications and standardsThe bolted type equipment bushing 400SFR-B meets the requirements of CENELEC EN 50180 and IEC 60137.
Equipmentbushing
type
VoltageUr
(kV)Interface
CurrentIr
(A)
Dia. D(mm)
400SFR-B
K400SFR-B
M400SFR-B
400SFR-B 1250 A
K400SFR-B 1250 A
M400SFR-B 1250 A
12
24
36
12
24
36
C1
C1
C1
C2
C2
C2
630
630
630
1250
1250
1250
25
25
25
32
32
32
Dia. 70
95
33
219.5
Dia. 70
Dia. 109
Dia. D
M12
In mm.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV18/30 (36) kV19/33 (36) kV
25
FIXINGS FOR EQUIPMENT BUSHINGS
400SFR-B Bushing for gas insulated switchgear
In mm.
MOUNTED
equipment
sealingO-ringgasket
equipmentconnection
bushinginterface 6 fixing
screwsM6
earthconnection
M4
30°
UNMOUNTED
60°
60°60°
Dia. 91.5Dia. 103.1
83
M6
earthconnectionM4
26
08/2
011
400A-24BINTERFACE C1
IN-AIR BUSHING
Up to 24 kV - 630 A
Ordering instructionsTo order the equipment bushing, specify the type.The bushings are supplied with an earth jumper.To include the ring clamp, add:• /B, if per British standards• /D, if per German standards• /F, if per French standards.E.g. 400A-24B/D.For use in potentially explosive atmospheres (for 12 kV max), order: -/ATEX.
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
Creepage distanceA-B
(mm)
400A-24B
400A-24B
12
24
630
630
520
520
In mm.Dia. 80
30
20
Dia. 80
Dia. 110
40
250
434
M16 B
A
Dia.25
ApplicationFor use in equipment insulated with air, typically for dry type transformers, motors, switchgear, capacitors...
Specifications and standardsThe bolted type equipment bushings 400A-24B are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180, IEC 60071 and IEC 60137.
27
400A-24B In-air bushing
In mm.
FIXINGS FOR EQUIPMENT BUSHINGS
10
Dia.12
Type BCA-B : BS 2562 British standardsType BCA-D : DIN 42 538 German standards
4Dia. 94.5
Dia. 111
BS 2562 stand.: 120DIN 42 538 stand.: 123
Dia. 150
F
120°
120°
Type BCA-F : NFC 52-053 French standards
Dia. 150
10
Dia.124
Dia. 94.5
Dia. 111
126
fixing studs andnuts M10
bushing interface
earth jumper
equipment
gasket
equipmentconnection
fixing flangeBCA-B orBCA-D
fixing flangeBCA-F
Fixing dimensions standards NF C 52-053French standards.
Fixing dimensions standards DIN 42 538German standards.
M10
Dia. 123Dia. 82
5520
4 fixingstuds
3 fixingstuds
Dia. 82
5220
M10
Dia. 126
28
08/2
011
In mm.
Equipmentbushing
type
VoltageUr
(kV)
CurrentIr
(A)
670AR-2K670AR-2
1224
12501250
6/10 (12) kV6,35/11 (12) kV
8,7/15 (17,5) kV12/20 (24) kV
12.7/22 (24) kV
Up to 24 kV - 1250 A
670AR-2INTERFACE D2
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors...
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings can be supplied with an earth jumper (/J) or an earth plate (/GS). This earth connection must be specified when ordering.E.g. K670AR-2/GS.
Specifications and standardsThe bolted type equipment bushings 670AR-2 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 60137.
10
Dia. 70Dia. 100Dia. 150
40
140
325
36
130
M16
Minimum oil level:-12 kV: 40 mm-24 kV: 50 mm
Dia.32
29
670AR-2/GS Bushing 670AR-2/J Bushing
FIXINGS FOR EQUIPMENT BUSHINGS
Fixing dimensions standards NF C 52-053French standards.
In mm.
Bushing clamping kitTo order the bushing clamping kit, according to NFC 52-053standards, simply specify KBCNF-400.Contents: - 4 x claw clamp NF400 - 1 x sealing gasket.
Bushing clamping kitTo order the bushing clamping kit with DIN style fixing flange, simply specify KBCDS-400.Contents: - 1 x fixing flange DIN style - 6 x stud clamp F DIN 42 538 - 1 x sealing gasket.
Fixing dimensions
Dia. 105Dia. 171
6030
6 fixingstuds
M10M10 or
M12
Dia. 105Dia. 171
50 to70 25
4 fixingstuds
NF C 52-053claw clamp
earth plate
bushing interface
fixing studs
equipment
equipmentconnection
sealing gasket
earth jumper
F DIN 42 538stud clamp
fixing flange
30
08/2
011
Specifications and standardsThe bolted type equipment bushings 900AR-X are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 60137.
Ordering instructionsTo order the equipment bushing, specify the type.Add a 'K' for use up to 24 kV, add an 'M' for use up to 36 kV,add a 'P' for use up to 42 kV.The bushings can be supplied with an earth jumper (/J) or an earth plate (/GS). This earth connection must be specified when ordering.E.g. 900AR-4/GS.
In mm.
Equipmentbushing
type
Interfacetype
VoltageUr
(kV)
CurrentIr
(A)
Dimensions (mm)
A B Dia. C
900AR-1900AR-2900AR-3900AR-4
F3F2F1F1
42423636
125063025002500
364364364259
175175175 70
32255050
Up to 42 kVUp to 2500 A
900AR-1 / 900AR-2900AR-3 / 900AR-4
INTERFACE F1, F2 & F3EQUIPMENT BUSHING
ApplicationFor use in equipment, typically for transformers, switchgear, capacitors... 6/10 (12) kV
6.35/11 (12) kV8.7/15 (17.5) kV
12/20 (24) kV12.7/22 (24) kV
18/30 (36) kV19/33 (36) kV
20.8/36 (42) kV
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
40
B
A
35
110.5
Dia. 150
Dia. 100
M16
Minimum oil level:-12 kV: 40 mm-24 kV: 50 mm-36 kV: 70 mm-42 kV: 120 mm
Dia. C
31
FIXINGS FOR EQUIPMENT BUSHINGS
900AR-X/GS Bushing
Bushing clamping kitTo order the bushing clamping kit, according to NFC 52-053standards, simply specify KBCNF-400.Contents: - 4 x claw clamp NF400 - 1 x sealing gasket.
In mm.
Fixing dimensions standards NF C 52-053French standards.
900AR-X/J Bushing
Bushing clamping kitTo order the bushing clamping kit with DIN style fixing flange, simply specify KBCDS-400.Contents: - 1 x fixing flange DIN style - 6 x stud clamp F DIN 42 538 - 1 x sealing gasket.
Fixing dimensions
earth jumper
earth plate
bushing interface
fixing studs
equipment
equipmentconnection
sealing gasket
NF C 52-053claw clamp400/630 series
F DIN 42 538stud clamp
fixing flange
Dia. 105Dia. 171
6030
6 fixingstuds
M10 orM12
M10 orM12
Dia. 105Dia. 171
50 to70 25
4 fixingstuds
32
NOTES
08/2
011
Additional catalogue information on power cable accessoriesis available by contacting us at the address below:
Nexans Network Solutions N.V. - Div. Euromold • Zuid III, Industrielaan 12, B-9320 ErembodegemTel.: +32 (0)53 85 02 11 • Fax: +32 (0)53 83 10 13 • www.nexans.com • [email protected]
Catalogue also available on CD-ROM
Distributed by:
a Nexans company