A., Klauk, H. Someya, T. -...

Documents

Peng, B., Chan, P.K.L.Flexible organic transistors on standard printing paper and memory properties induced by floated gate electrode

(2014) Organic Electronics: physics, materials, applications, 15 (1), pp. 203-210. Cited 2 times.

Department of Mechanical Engineering, University of Hong Kong, Pokfulam Road, Hong Kong, Hong Kong

Abstract

Integrating electronic devices with unconventional substrate has been a popular research direction. Among these substrates,cellulose fiber paper has advantages in low-cost, recyclable and bio-degradable. We demonstrated directing printing of all contactelectrodes on standard untreated Fuji Xerox printer paper without using planarization layer. The screen-printed gate electrodesbased on silver nanoparticles can smooth out the paper substrate surface by two orders of magnitude and allow us to useparylene and DNTT as the dielectric and active layer directly. The transistors show average mobility of 0.297 cm 2 V-1 s-1 andon/off ratio larger than 105. The low leakage current allows us to demonstrate memory properties by employing the floated gatemethod. The devices show excellent memory retention time for more than 10,000 s. The unique flexibility and combustibility ofthe organic transistors on paper substrate manifest their applications as next generation of green electronics. © 2013 ElsevierB.V. All rights reserved.

Author Keywords

Cellulose fiber paper; Floated gate; Memory; Screen-printing

Index Keywords

Cellulose fiber, Floated gate, Low-leakage current, Memory retention time, Orders of magnitude, Organic transistor, Planarizationlayers, Silver nanoparticles; Data storage equipment, Dielectric materials, Refractory metalcompounds, Silver, Substrates, Textile fibers; Printing; Cellulose Fibers, Paper, Silk Screen Printing, Silver, Substrates, TextileFibers

References

Becerril, H.A., Roberts, M.E., Liu, Z.H., Locklin, J., Bao, Z.N.High-performance organic thin-film transistors through solution-sheared deposition of

small-molecule organic semiconductors(2008) Adv. Mater., 20, pp. 2588-2594.

Li, H.Y., Tee, B.C.K., Giri, G., Chung, J.W., Lee, S.Y., Bao, Z.N.High-performance transistors and complementary inverters based on solution-grown

aligned organic single-crystals

(2012) Adv. Mater., 24, pp. 2588-2591.

Zschieschang, U., Kang, M.J., Takimiya, K., Sekitani, T., Someya, T., Canzler, T.W., Werner,A., Klauk, H.Flexible low-voltage organic thin-film transistors and circuits based on C-10-DNTT

(2012) J. Mater. Chem., 22, pp. 4273-4277.

Yokota, T., Sekitani, T., Tokuhara, T., Take, N., Zschieschang, U., Klauk, H., Takimiya, K.,Someya, T.Sheet-type flexible organic active matrix amplifier system using pseudo-CMOS circuits

with floating-gate structure

(2012) IEEE Trans. Electron Dev., 59, pp. 3434-3441.

Scopus - Print Document http://www.scopus.com/citation/print.url?origin=recordpage&sid=&src...

1 z 5 6. 11. 2014 9:10

Sokolov, A.N., Cao, Y.D., Johnson, O.B., Bao, Z.A.Mechanistic considerations of bending-strain effects within organic semiconductors on

polymer dielectrics

(2012) Adv. Funct. Mater., 22, pp. 175-183.

Klauk, H., Zschieschang, U., Pflaum, J., Halik, M.Ultralow-power organic complementary circuits

(2007) Nature, 445 (7129), pp. 745-748. DOI 10.1038/nature05533, PII NATURE05533

Sekitani, T., Zschieschang, U., Klauk, H., Someya, T.Flexible organic transistors and circuits with extreme bending stability

(2010) Nat. Mater., 9, pp. 1015-1022.

Eder, F., Klauk, H., Halik, M., Zschieschang, U., Schmid, G., Dehm, C.Organic electronics on paper

(2004) Appl. Phys. Lett., 84, pp. 2673-2675.

Tobjork, D., Osterbacka, R.Paper electronics

(2011) Adv. Mater., 23, pp. 1935-1961.

Khan, M.A., Bhansali, U.S., Alshareef, H.N.High-performance non-volatile organic ferroelectric memory on banknotes

(2012) Adv. Mater., 24, pp. 2165-2170.

Irimia-Vladu, M., Sariciftci, N.S., Bauer, S.Exotic materials for bio-organic electronics

(2011) J. Mater. Chem., 21, pp. 1350-1361.

Li, Y., Liu, C., Xu, Y., Minari, T., Darmawan, P., Tsukagoshi, K.Solution-processed organic crystals for field-effect transistor arrays with smooth

semiconductor/dielectric interface on paper substrates

(2012) Org. Electron., 13, pp. 815-819.

Zschieschang, U., Yamamoto, T., Takimiya, K., Kuwabara, H., Ikeda, M., Sekitani, T., Someya,T., Klauk, H.Organic electronics on banknotes

(2011) Adv. Mater., 23, pp. 654-658.

Martins, R., Nathan, A., Barros, R., Pereira, L., Barquinha, P., Correia, N., Costa, R.,Fortunato, E.Complementary metal oxide semiconductor technology with and on paper

(2011) Adv. Mater., 23, pp. 4491-4496.

Lu, Y., Zhang, Y.-H.P., Lynd, L.R.Enzyme-microbe synergy during cellulose hydrolysis by Clostridium thermocellum

(2006) Proceedings of the National Academy of Sciences of the United States of

America, 103 (44), pp. 16165-16169. DOI 10.1073/pnas.0605381103


2 z 5 6. 11. 2014 9:10

Swatloski, R.P., Spear, S.K., Holbrey, J.D., Rogers, R.D.Dissolution of cellose with ionic liquids

(2002) Journal of the American Chemical Society, 124 (18), pp. 4974-4975. DOI 10.1021/ja025790m

Yun, D.J., Lim, S.H., Lee, T.W., Rhee, S.W.Fabrication of the flexible pentacene thin-film transistors on 304 and 430 stainless steel

(SS) substrate

(2009) Org. Electron., 10, pp. 970-977.

Fritz, S.E., Kelley, T.W., Frisbie, C.D.Effect of dielectric roughness on performance of pentacene TFTs and restoration of

performance with a polymeric smoothing layer

(2005) Journal of Physical Chemistry B, 109 (21), pp. 10574-10577. DOI 10.1021/jp044318f

Desai, T.V., Woll, A.R., Engstrom, J.R.Thin film growth of pentacene on polymeric dielectrics: Unexpected changes in the

evolution of surface morphology with substrate

(2012) J. Phys. Chem. C, 116, pp. 12541-12552.

Kato, Y., Iba, S., Teramoto, R., Sekitani, T., Someya, T., Kawaguchi, H., Sakurai, T.High mobility of pentacene field-effect transistors with polyimide gate dielectric layers

(2004) Appl. Phys. Lett., 84, pp. 3789-3791.

Skvarla, J., Luxbacher, T., Nagy, M., Sisol, M.Relationship of surface hydrophilicity, charge, and roughness of PET foils stimulated

by incipient alkaline hydrolysis

(2010) ACS Appl. Mater. Int., 2, pp. 2116-2127.

Martins, R., Barquinha, P., Pereira, L., Correia, N., Goncalves, G., Ferreira, I., Fortunato, E.Write-erase and read paper memory transistor(2008) Appl. Phys. Lett., 93, p. 203501.

Martins, R., Barquinha, P., Pereira, L., Correia, N., Goncalves, G., Ferreira, I., Fortunato, E.Selective floating gate non-volatile paper memory transistor

(2009) Phys. Status Solidi RRL, 3 (9), pp. 308-310.

Peiponen, K.E., Myllylä, R.SpringerLink (Online service) Optical measurement techniques innovations for industry

and the life sciences

(2008) Springer Series in Optical Science, Springer Berlin, London (136)

Kuribara, K., Wang, H., Uchiyama, N., Fukuda, K., Yokota, T., Zschieschang, U., Jaye, C.,Someya, T.Organic transistors with high thermal stability for medical applications

(2012) Nat. Commun., 3.

Trantidou, T., Prodromakis, T., Toumazou, C.Oxygen plasma induced hydrophilicity of Parylene-C thin films


3 z 5 6. 11. 2014 9:10

(2012) Appl. Surf. Sci., 261, pp. 43-51.

Kawasaki, N., Kalb, W.L., Mathis, T., Kaji, Y., Mitsuhashi, R., Okamoto, H., Sugawara, Y.,Batlogg, B.Flexible picene thin film field-effect transistors with parylene gate dielectric and their

physical properties

(2010) Appl. Phys. Lett., 96, p. 113305.

Dibenedetto, S.A., Facchetti, A., Ratner, M.A., Marks, T.J.Molecular self-assembled monolayers and multilayers for organic and unconventional

inorganic thin-film transistor applications

(2009) Adv. Mater., 21, pp. 1407-1433.

Ulman, A.Formation and structure of self-assembled monolayers

(1996) Chemical Reviews, 96 (4), pp. 1533-1554.

Lee, H.M., Lee, H.B., Jung, D.S., Yun, J.Y., Ko, S.H., Park, S.B.Solution processed aluminum paper for flexible electronics

(2012) Langmuir, 28, pp. 13127-13135.

Siegel, A.C., Phillips, S.T., Dickey, M.D., Lu, N.S., Suo, Z.G., Whitesides, G.M.Foldable printed circuit boards on paper substrates

(2010) Adv. Funct. Mater., 20, pp. 28-35.

Jedaa, A., Halik, M.Toward strain resistant flexible organic thin film transistors

(2009) Appl. Phys. Lett., 95, p. 103309.

Russo, A., Ahn, B.Y., Adams, J.J., Duoss, E.B., Bernhard, J.T., Lewis, J.A.Pen-on-paper flexible electronics(2011) Adv. Mater., 23, pp. 3426-3430.

Naber, R.C.G., Asadi, K., Blom, P.W.M., De Leeuw, D.M., De Boer, B.Organic nonvolatile memory devices based on ferroelectricity

(2010) Adv. Mater., 22, pp. 933-945.

Han, S.T., Zhou, Y., Wang, C.D., He, L.F., Zhang, W.J., Roy, V.A.L.Layer-by-layer-assembled reduced graphene oxide/gold nanoparticle hybrid double-

floating-gate structure for low-voltage flexible flash memory

(2013) Adv. Mater., 25, pp. 872-877.

Wang, S.M., Leung, C.W., Chan, P.K.L.Nonvolatile organic transistor-memory devices using various thicknesses of silver

nanoparticle layers

(2010) Appl. Phys. Lett., 97, p. 023511.

Wang, S.M., Leung, C.W., Chan, P.K.L.Enhanced memory effect in organic transistor by embedded silver nanoparticles

(2010) Org. Electron., 11, pp. 990-995.


4 z 5 6. 11. 2014 9:10

About Scopus

What is ScopusContent coverage

Customer Service

Help and ContactLive chat

About Elsevier

About ElsevierTerms and ConditionsPrivacy Policy

Copyright © 2014 Elsevier B.V. All rights reserved. Scopus® is a registered trademark of Elsevier B.V.Cookies are set by this site.To declinethem or learn more,visit our Cookies page.

Song, S.H., Yang, H.H., Han, C.H., Ko, S.D., Lee, S.H., Yoon, J.B.Metal-oxide-semiconductor field effect transistor humidity sensor using surface

conductance

(2012) Appl. Phys. Lett., 100, p. 101603.

Zhu, J.-J., Liao, X.-H., Zhao, X.-N., Chen, H.-Y.Preparation of silver nanorods by electrochemical methods

(2001) Materials Letters, 49 (2), pp. 91-95. DOI 10.1016/S0167-577X(00)00349-9, PII S0167577X00003499

Chou, K., Ren, C.Synthesis of nanosized silver particles by chemical reduction method

(2000) Mater. Chem. Phys., 64, pp. 241-246.

Correspondence Address

Chan P.K.L.; Department of Mechanical Engineering, University of Hong Kong, Pokfulam Road, Hong Kong, Hong Kong; email:[email protected]

ISSN: 15661199CODEN: OERLADOI: 10.1016/j.orgel.2013.11.006Language of Original Document: EnglishAbbreviated Source Title: Org. Electron.: phys. mater. appl.Document Type: ArticleSource: Scopus


5 z 5 6. 11. 2014 9:10

Documents

Topiarzová, R., Čablík, V.Potential application of flotation in separating PET and PLA materials [Potencjalne zastosowanie flotacji w oddzielaniumateriałów PET i PLA]

(2011) Inzynieria Mineralna, 12 (2), pp. 89-97.

Institute of Environmental Engineering, Faculty of Mining and Geology, VŠB - Technical University Ostrava, 17. Iistopadu 15, 70833 Ostrava - Poruba, Czech Republic

Abstract

The concept of biodegradable plastics, i.e. biologically degradable materials, appears to be a possible solution for an evergrowing production of plastic wastes as the biodegradable plastics shall have a substantially lower environmental impact and beable to at least partially substitute the production of plastics from oil derivatives. Currently, a promising direction seems to be thedevelopment of a polymer on the base of lactic acid, called polylactic acid (PLA). Packaging made from the material, mainlydrinks bottles, could be used on a mass basis in future. Such generated waste will have to be recycled, which shall bringproblems connected with separation of biodegradable material from common plastics. This paper deals with the issue ofseparation of PLA from PET (polyethylene terephthalate). Mixing the above mentioned plastics in the recycling process leads totheir devaluation. Due to the occurrence of PLA material the quality of the feedstock decreases during recycling PET bottles. Thecurrently implemented research at the Institute of Environmental Engineering of Mining Faculty - Technical University of Ostravaexamines the possibilities of separating the two materials by means of flotation. This method has brought a partial success, moreeffective results are expected after its optimization.

Author Keywords

Biodegradable plastics; Flotation; PET; PLA

References

(2011) About PET, online, cit. 2011-08-09, Available on WWW

Nezval, J.Přehled O Recyklaci PET Metodou B2B ("bottle to Bottle"). PETrecycling CZ, online. 26.05.2006, 01, cit. 2011-08-22. Available on WWW

Lagaron, J.M., Lopez-Rubioa, A.Nanotechnology for bioplastics: Next term opportunities, challenges and strategiesTrends in Food Science & Technology, online. 1.7.2011, 1016, cit. 2011-08-09. Available on WWW

(2010) The Ingeo Journey, online, cit. 2011-08-09, Available on WWW

Södergård, A., Stolta, M.Properties of lactic acid based polymers and their correlation with composition(2002) Progress in Polymer Science, online. July, 6, cit. 2011-08-09. Available on WWW

(2010) Bioobaly, online, cit. 2011-08-09, Available on WWW

Nature Works LLC, online, updated 01.09.2009. Available on WWW


1 z 3 5. 11. 2014 12:08

Sánchez, A.C., Collinson, S.R.The selective recycling of mixed plastic waste of polylactic acidnext term andpolyethylene terephthalate by control of process conditionsEuropean Polymer Journal, online. 13.7.2011, 2, cit. 2011-08-09. Available on WWW

OBRUČKA Stanislav, Gate2Biotech Aktualizováno 05.07.2008, online, Available on WWW

Tachwalia, Y., Al-Assaf, Y., Al-Ali, A.R.Automatic multistage classification system for plastic bottles recyclingn term(2007) Resources, Conservation and Recycling, p. 2. online. December, cit. 2011-08-09. Available on WWW

Fečko, P.(2001) Netradiční Způsoby Úpravy Č ernouhelných kalů, p. 150. Ostrava: VŠB-TU Ostrava, ISBN 80-7078-921-2

Ghauri, M.A.Status of coal biotechnology in Pakistan(2009) 18th International Conference IBS, pp. 513-516. DONATI, Edgardo R., et al, Bariloche, Argentina: s.n.

online. updated 06.010.2010. Available on: WWW

Carvalho, T., Durão, F., Ferreira, C.Separation of packaging plastics by froth flotation in a continuous pilot plant(2010) Waste Management, 30, p. 11. online, cit. 2010-11-09. Available on WWW

Sisol, M., Ľubica, K., Tomáš, B.Flotačná separácia PET zo zmesi odpadových plastov PET, PVC a PS(2005) Acta Montanistica Slovaca, 10 (Special 1), pp. 45-48.

Davis, G., Song, J.H.Biodegradable term packaging based on raw materials from crops and their impact onwaste management(2006) Industrial Crops and Products, p. 2. online. March, cit. 2011-08-22. Available on WWW

Kmeť, S.(1983) Flotácia. Vysoká Škola Technická V Kosicich, Banická Fakulta, Alfa Bratislava, p. 389. ISBN II-178924-6343/83

Konopacka, Z.(2005) Flotacja Mechaniczna, online. Wroclaw: s.n., cit. 2010-08-20. Available on WWW


2 z 3 5. 11. 2014 12:08

About ScopusWhat is ScopusContent coverage

Customer ServiceHelp and ContactLive chat

About ElsevierAbout ElsevierTerms and ConditionsPrivacy Policy


Kintiszewa-Dimitrowa, R., Stoew, S.Flokulacja selektywna(1987) Katovice, Ślask, p. 103. ISBN 83-216-0637-7

Flotation Method of Separation of Mixture of Plastics, online. Freepatentsonline, update 06.010.2010

Štofko, M., Štofková, M.Neželezné kovyEmilea, Košice, p. 304. ISBN 80-7099-527-0

(2010), online, cit. 2011-08-22. Available on WWW

(2010), online, cit. 2011-08-22. Available on WWW

Shen, L., Worrell, E., Patel, K.M.Open-loop recycling: A LCA case study of PET bottle term-to-fibre recycling(2010) Resources, Conservation and Recycling, p. 1. November, cit. 2011-08-22. Available on WWW

Correspondence AddressTopiarzova R.; Institute of Environmental Engineering, Faculty of Mining and Geology, VŠB - Technical University Ostrava, 17.Iistopadu 15, 708 33 Ostrava - Poruba, Czech Republic; email: [email protected]

ISSN: 16404920Language of Original Document: Polish; EnglishAbbreviated Source Title: Inzynieria MineralnaDocument Type: ArticleSource: Scopus


3 z 3 5. 11. 2014 12:08

Documents

Janošková, K., Müller, G.Biosorption of cadmium from aqueous solutons using orange peel, walnut and hazelnut shell

(2011) 11th International Multidisciplinary Scientific Geoconference and EXPO - Modern Management of Mine Producing,

Geology and Environmental Protection, SGEM 2011, 3, pp. 799-806.

Technical university in Košice, Slovakia

Abstract

Biosorption of Cd(II) ions from aqueous solutions has been studied and determined to adsorption capacity. The experimental dataobtained from batch equilibrium tests have been analyzed by three two-parameter (Freundlich, Langmuir and Temkin) isothermmodels, four three-parameter (Redlich-Peterson, Sips, Toth and Khan) isotherm models and kinetic models including thepseudo-first order and pseudo-second order. The adsorption data fit well with Temkin isotherm for orange peel and Freundlichisotherm for walnut and hazelnut shell. Maximum experimental adsorption capacity was found to be 13.947, 8.57 and 8.847 mg/gfor orange peel, walnut shell and hazelnut shell, respectively. Experimental kinetics data was well-fitted for pseudo-second orderfor all adsorbents and correlation coefficient for kinetics was above 90%. © SGEM2011 All Rights Reserved by the InternationalMultidisciplinary Scientific GeoConference SGEM.

Author Keywords

Biosorption; Cadmium; Isotherm; Kinetic

Index Keywords

Adsorption capacities, Adsorption data, Batch equilibrium, Correlation coefficient, Experimental kinetics, Freundlichisotherm, Pseudo second order, Temkin isotherm; Biosorption, Cadmium, Citrus fruits, Exhibitions, Isotherms, Kinetics, Shells(structures); Cadmium compounds

References

Wang, Z.S., Li, Z.Z., Tao, S.R.Removal of chromium (VI) from aqueous solution using walnut hull

(2009) Journal of Environmental Management, 90, pp. 721-729.

Pehlivan, E., Altun, T.Biosorption of chromium (VI) ion from aqueous solutions using walnut, hazelnut and

almond shell

(2008) Journal of Hazardous Materials, 155, pp. 378-384.

Zabihi, M., Ahmadpour, A., Haghighi Asi, A.Removal of mercury from water by carbonaceous sorbents derived from walnut


Bhattacharya, A.K., Mandal, S.N., Das, S.K.Adsorption of Zn(II) from aqueous solution by using different adsorbents

(2006) Chemical Engineering Journal, 123, pp. 43-51.

Dandan, L., Cao, Q., Li, X., Luo, F., Shao, W.Kinetics and equilibrium of Cu(II) adsorption onto chemically modified orange peel

cellulose biosorbents

(2009) Hydrometallurgy, 95, pp. 145-152.


1 z 3 5. 11. 2014 12:08

Vereš, J., Bakalár, T., Búgel, M., Sisol, M.Examination of the mutual interaction of heavy metals in course of adsorption from

model solutions

(2008) Chemicke Listy, 102 (15), pp. s503-s504.

Bakalár, T., Búgel, M., Pavolová, H.Equilibrium modeling of Cu and Ni removal from aqueous solutions: Influence of

salinity

(2008) Proc. World Acad. Sci. Eng. Technol, 34, pp. 252-255.

Özer, A., Pirinççi, H.B.The adsorption of Cd(II) ions on suplhuric acid-treated wheat bran

(2006) Journal of Hazardous Materials, B137, pp. 849-855.

Pérez-Marín, A.B., Meseguer Zapata, V., Ortuño, J.F., Aguilar, M., Sáez, J., Lloŕens, M.Removal of cadmium from aqueous solutions by adsorption onto orange waste


Tenorio, J.A.S., Espinosa, D.C.R.Treatment of chromium plating process effluents with ion exchange resins

(2001) Waste Management, 21, p. 637.

Gode, F., Pehlivan, E.Removal of Cr(VI) from aqueous solution by two Lewatitanion exchange resins


Katsou, E., Malamis, S., Haralambous, K.Examination of zinc uptake in a combined system using sludge, minerals and

ultrafiltration membranes


Alyüz, B., Veli, S.Kinetics and equilibrium studies for the removal of nickel and zinc from aqueous

solutions by ion exchange resins


Dizge, N., Keskinler, B., Barlas, H.Sorption of Ni(II) ions from aqueous solution by Lewatit cation-exchange resin


Günay, A., Arslankaya, E., Tosun, I.Lead removal from aqueous solution by natural and pretreated clinoptilolite:Adsorption equilibrium and kinetics


Ho, Y.S., McKay, G.A comparison of chemisorption kinetic models applied to pollutant removal on various

sorbents

(1998) Trans. IChem E, 76 B, pp. 332-340.


Technical university in KošiceSlovakia


2 z 3 5. 11. 2014 12:08

About Scopus


Customer Service


About Elsevier



Conference name: 11th International Multidisciplinary Scientific Geoconference and EXPO, SGEM 2011Conference date: 20 June 2011 through 25 June 2011Conference location: VarnaConference code: 101584

Language of Original Document: EnglishAbbreviated Source Title: 11th Int. Multidisciplinary Sci. Geoconf. EXPO - Mod. Manage. Mine Producing, Geology Environ.ProtectionDocument Type: Conference PaperSource: Scopus


3 z 3 5. 11. 2014 12:08

Documents

Simackova, H.a , Nejedlík, M.a , Vyvážil, M.a , Jančová, J.a , Ledererová, J.a , Svoboda, M.a , Čablík, V.b

Economic view of possibilities of CCPs utilization in building products [Ekonomiczne spojrzenie na wykorzystanie CCP

w materiałach budowlanych](2011) Inzynieria Mineralna, 12 (2), pp. 11-21. Cited 2 times.

a Research Institute of Building Materials, JSC, Hněvkovského 65, 617 00 Brno, Czech Republicb VŠB-Technical University of Ostrava, Faculty of Mining and Geology, 17. Iistopadu 15, 708 33 Ostrava-Poruba, Czech Republic

AbstractThere is a steadily growing trend of looking for new possibilities of CCPs utilization with the aim to substitute non-renewablenatural resources. The Research Institute of Building Materials has been interested in these problems for a long time and it hasbeen solving many projects in this field. One of them is Research centre for integrated system development concerning utilizationof by-products of energy resource mining and processing. In addition to ecological and technological questions, this project alsodescribes economic assessment of newly designed building products made from CCPs. Economic point of view is often a barrierfor successful entry into a market. This paper mainly focuses on economic utilization of fly ashes in production of artificialaggregates and dry mortar mixes.

Author KeywordsBuilding products; Coal combustion produkt; Economics

References

Suchardová, M., Šimáčková, H.Continuous Reports on Solution of 'Research Centre for Integrated System Development

Concerning Utilization of By-products of Energy Resource Mining and Processing' in

2006-2010,

Vyvážil, M., Ledererová, J., Svoboda, M., Bibora, P., Rubek, A.Artificial aggregate produced in the cold according to the purpose of the usage(2009) XIIth International Conference of Research Institute of Building Materials "Ecology and

New Building Materials and products", pp. s46-51. Telč 9.6. - 11. 6, ISBN 978-80-254-4447-4

Vyvážil, M., Bibora, P., Leber, P., Ledererová, J., Svoboda, M.Vhodnost vedlejších energetických produktů pro výrobu umělého kameniva zastudena, 4. Ročník česko - Slovenského symposia Výsledky výzkumu a vývoje proodpadové hospodář ství(2009) Milovy, 22-24, p. 4. ISBN 978-80-02-02108-7

Vyvážil, M., Bibora, P., Ledererová, J., Svoboda, M., Rubek, A.Artificial aggregate on base of secondary energetic products produced by cold wayaccording to the purpose of the usage(2009) 13th International Conference on Environment and Mineral Processing, VŠB-TU Ostrava, ISBN 978-80-248-1995-2

(2009) Směs Ke Zhotovení Umělého Pórovitého Kameniva do Konstrukcí Na Bázi

Vysokoteplotního Popílku - Užitný Vzor Přihlášený Pod č. 2009-21879, dne 2.11, zapsaný pod č. CZ 20315 Ul dne 3.12.2009. Úřad průmyslového vlastnictví Praha.


1 z 2 5. 11. 2014 12:10





Autoři: Ledererová Jaroslava, Svoboda Miroslav, Chromková Ivana, Vyvážil Martin

Ledererova, J.About basic aspects of ecological and economical utilization of industrial wastematerials(2006) X. Konference "Ekologie a Nove Stavebni Hmoty a vyrobky", pp. 8-11. original in Czech, Vustah Brno;, ISBN 80-239-7146-8

Kusnierova, M., Fecko, P., Cablik, V., Pectova, I., Mucha, N.Extracting unburnt coal from black coal fly ash(2007) 2007 NSTI Nanotechnology Conference and Trade Show - NSTI Nanotech 2007,

Technical Proceedings, 4, pp. 628-631. 2007 NSTI Nanotechnology Conference and Trade Show - NSTI Nanotech 2007, TechnicalProceedings

Jacko, V., Michalikova, F.Possibilities of utilization of black coal ash from energetics of U. S. Steel kosice(original in Slovak language: Moznosti zuzitkovania ciernouholného popolceka zenergetiky U. S. Steel Kosice(2005) Acta Montanistica Slovaca, 10 (1), pp. 209-213. ISSN 1335-1788

Kušnierová, M., Praščáková, M., Čablik, V., Fečko, P.Odpady energetyczne jako substytut niemetalicznych surowców pierwotnych(2011) Journal of the Polish Mineral Engineering Society, (1-27), pp. 73-78. ISSN 1640-4920

Michalíková, F., Škvarla, J., Sisol, M., Krinická, I., Kolesárová, M.Technologie przeróbcze uszlachetniania, zawierajqeych czȩści palne, popiolów lotnychz wȩgli kamiennych spalanych w elektrocieplowniach(2010) Inżynieria Mineralna z, 1-2 (25-26), pp. s9-26. Wyd. Polskiego Towarzystwa Przeróbki Kopalin, Kraków, ISSN 1640-4920


Simackova H.; Research Institute of Building Materials, JSC, Hněvkovského 65, 617 00 Brno, Czech Republic

ISSN: 16404920Language of Original Document: Polish; EnglishAbbreviated Source Title: Inzynieria MineralnaDocument Type: ReviewSource: Scopus


2 z 2 5. 11. 2014 12:10

Documents

Bindzár, P., Malindžák, D.Number of conveyor belts optimization regarding to its type and logistical parameters in mining industry [Optimalizáciapočtu dopravných pásov s ohl'adom na ich typ a logistické parametre v t'ažobnom podniku]

(2008) Acta Montanistica Slovaca, 13 (4), pp. 524-531.

Ústav logistiky priemyslu a dopravy, Park Komenského 14, 043 84 Košice, Slovakia

AbstractMaterial transportation by belt conveyers is widely used in many industrial branches including mining plants. Belt conveyingdevelopment during the last year was oriented mainly on construction of belts. The consequence of this is the improvement of itsmanufacture qualities bringing down the costs for their exchange and maintenance.Despite the fact that there are sometheoretical calculations based on a standards it is common in the industry that the belt is not properly selected or it isoverdesigned or number of its types is too large what can lead to increased costs for its storage. The paper describes theoptimization of number of belt types in mining company SIDERIT, s. r. o. Nižná Slaná by the method of modernization andunification of belts under practical skills and projecting based on theoretical calculations.

Author KeywordsBelt optimization; Conveyor belt designing; Material flow; Mining industry

References

Fries, J.Lifetime prolongation of belt conveyor's drums by design changes, pp. 7-14. Transport and Logistics, No. 13/2007, Beograd 2007, ISSN 1451-107X

Gondek, H., Skařupa, J., Šamárek, J.(2003) Optimisation of belt conveying transport routes, pp. 5-13. Transport and Logistics, No. 04/2003, Košice, ISSN 1451-107X

Grujić, M., Despodov, Z., Ristović, I.(2007) Possibility of applying the multicriteria analysis method when selecting a conveyance

system in lead and zinc mine, pp. 7-14. Transport and Logistics, No. 13/2007, Beograd, ISSN 1451-107X

Jurman, J., Škvareková, E., Fries, J.(2004) Možnosti využití metody SBRA k definování spolehlivosti lan, pp. 163-170. ISSN 1451-107X, 24.-26.5, "Transport & Logistics", Krivda 2004, Košice, Podbanské

Krešák, J., Kropuch, S., Peterka, P.Stend pre prierazové skúšky pásov(1999) Acta Montanistica Slovaca, 4 (1), pp. 39-44. ISSN 1335-1788

Lauhoff, H.Speed control on belt conveyors - does it really save energy?(2006) VII International symposium organized by Department of Mining Mechanization

Engineering, pp. 9-27. Beograd, September, ISBN 86-7352-175-0


1 z 3 5. 11. 2014 12:13

Malindžák, D.(1997) Výrobná logistika, p. 170. Košice: FBERG TU

Malindžák, D., Straka, M., Viestová, K.Doprava ako súčasť logistického systému: Základné členenie a charakteristiky(2007) Doprava a logistika: Odborný mesačník vydavateľstva ecopress, 2 (5), pp. 20-21. Internet, ISSN 1337-0138

Pinka, J., Wittenberger, G., Engel, J.(2006) Dobývanie ložísk vrtmi, p. 227. Košice:TU, ISBN 80-8073-625-1

Ristović, I., Adamović, J., Savić, L.Application of OpTrans software on the example of refractory clay deposit bukovikArandjelovac7th International sympozium on mine haulage and hoisting, Tara, Jun 01-04 2008, s.89-93. University of Belgrade. ISBN 978-86-7352-197-8

Rosová, A., Balog, M.Materiálovýtok(2007) Logistika v praxi: Praktická příručka manažera logistiky, p. 5. květen, ISSN 1801-8009.v530

Rosová, A.Všeobecný model toku výrobního procesu(2007) Logistika v praxi: Praktická příručka manažera logistiky, p. 6. květen, ISSN 1801-8009

Rosová, A., Balog, M.Modul kapacitní bilance(2007) Logistika v praxi: Praktická příručka manažera logistiky, p. 6. srpen, ISSN 1801-8009

Sisol, M., Kozáková, L., Bakalár, T.Flotačná separácia PET zo zmesi odpadových plastov PET, PVC a PS(2005) Acta Montanistica Slovaca, 10 (1), pp. 45-48. mimoriadne, ISSN 1335-1788

Šaderová, J., Boroška, J.(2005) Výrobné procesy, p. 82. 1. vyd.. Košice: TU, ISBN 80-8073-268-X


Bindzar P.; Ústav logistiky priemyslu a dopravy, Park Komenského 14, 043 84 Košice, Slovakia; email: [email protected]

ISSN: 13351788Language of Original Document: SlovakAbbreviated Source Title: Acta Montanistica SlovacaDocument Type: ArticleSource: Scopus


2 z 3 5. 11. 2014 12:13




Copyright © 2014 Elsevier B.V. All rights reserved. Scopus® is a registered trademark of Elsevier B.V.Cookies are set bythis site.To decline them or learn more,visit our Cookies page.


3 z 3 5. 11. 2014 12:13

Documents

Biáha, V.a , Kal'avský, F.b

Application of dry separative methods for decreasing content the residues unburned coal and separation Fe from blackcoal flies ash [Aplikácia suchých separačných metód pre znižovanie obsahu zvyškov nespáleného uhlia a separácie Fez čiernouhol'ných popolčekov](2008) Acta Montanistica Slovaca, 13 (2), pp. 235-240. Cited 2 times.

a Ústav Pre Výrskuin Rúd, Košice a.s., Magnezitárska 11, Košice, Slovakiab Univerzita Pavla Jozeta Šafánika, Prírodovedecká Fakulta, Ustav Chemických Vied, Moyzesova 11, Košice, Slovakia

AbstractMain obstacle using of fly ashes in building, that is its main consumer, is the residue of unburned coal; it is expressed of loss onignition - LOI. In present, the valid STN and EU standard limits the content of LOI to 3 - 5 %, in national conditions maximum 7 %.Application of processing technologies also has to assure utilization of fly ash that provides a possibility of complex utilization ofindividual products obtained by modification. By means of corona separation, based on different conductivity of individual fly ashelements, it is possible to separate unburned coal particles. The fly ash sample from black coal burning in melting boiler that wasdeposited on fly ash deposit, content of LOI of dielectric particle 6,45 % at 61 % weight yield was achieved. In the samples takenfrom dry taking of fly ash the non-conducting product contained 7,72 % of LOI at 73 % of weight yield.

Author KeywordsFly ash; High tension separation; Magnetic separation; Unburned carbon

References

Michalfková, F., Jacko, V., Sisol, M., Kozáková, E.: Teplárenská troska - vlastnosti, -prava apoužitie. Acta Montanistica Slovaca. roc. 10, mimoriadne e. 1 (2005), s. 91-96.http://actamont.tuke.sk/. ISSN 1335-1788.

Michaliková, F., Jacko, V., Sisol, M., Kozáková, I.Úpravnicke technológie získavania úž itkových zložiek z tuhých odpadov zo spal'ovaniauhlia v elektráthach

Michaliková, F., Sisol, M., Hreus, P.: Ziskavanie úžitkových zložiek z popolov s použitimsuchých úpravníckych procesov. In: Recyklace odpadů X: 3.11.2006 VŠB-TU Ostrava.Ostrava: VŠB-TU, 2006. p. 103-108. ISBN 80-248-1214-2.

Michalíková, F., Škvarla, J., Zeleňák, F.: Vlastnosti energetických popolčekov a možnosti ichvyužitia. Odpady (ČR) 12, no. 2 (2002), p. 20-21. ISSN 1210-4922.

Špaldon, F.Úprava nerastných surovin.(1986) Alfa -SNTL Praha, 480 s

Fečko, P., Kušnierová, M., Lyčková, B., Čablík, V., Farkašová, A.: Popílky. Monografia. VŠBTU Ostrava, HGF, Institut environmentá lniho inženýrství, 187 strán, 2003, ISBN80-248-0327-5.

Stehlíková, B.Ekonomické možnosti zúžitkovania hnedouhol'ných popolov z tepelných elektrárníZpravodaj Hnědé uhli. č. 3 (2005), s. 5-12. ISSN 1213-1660,


1 z 2 5. 11. 2014 12:14

Juraj

Zvýraznenie

Juraj

Zvýraznenie





Škvareková, E., Kozáková, Energetické zhodnotenie tuhých odpadov a klasických palív. In:Technická diagnostika: Mezinárodní vědecká konference při příležitosti 55 let založení Fakultystrojní Vysoké školy báňské - Technické univerzity Ostrava : Ostrava, 7. - 9. září 2005.Ostrava : VŠB - TU, 2005. s. 334-342. ISSN 1210-311X.

Tribo Flow Separations, 1525 Bull Lea Road, Suite 10, Lexington, KY 40511, USA: Laboratory- Scale Triboelectric Processing of a Combustion Ash, Výskumná správa pre UVR Košice a.s.,2006.

Soong, Y., et., al.Dry beneficiation of high loss-on-ignition fly ash(2002) Separation and Purification Technology, 26, pp. 177-184. s

Correspondence AddressBiaha V.; Ústav Pre Výrskuin Rúd, Košice a.s., Magnezitárska 11, Košice, Slovakia; email: [email protected]

ISSN: 13351788Language of Original Document: SlovakAbbreviated Source Title: Acta Montanistica SlovacaDocument Type: ArticleSource: Scopus


2 z 2 5. 11. 2014 12:14

Documents

Václavík, V.a , Daxner, J.b , Valíček, J.c , Dvorský, T.d , Kušnerová, M.c , Harničárová, M.c , Bendová, M.e , Břenek, A.a

The use of industrial waste as a secondary raw material in restoration plaster with thermal insulating effect(2014) Advanced Materials Research, 897, pp. 204-214.

a Institute of clean technologies for mining and utilization of raw materials for energy use, Institute of Environmental Engineering,VŠB-Technical University of Ostrava, 17. listopadu 15, 708 33 Ostrava-Poruba, Czech Republicb TexColor Ostrava, spol. s r.o, Na Mlýnici 33/1a, 708 00 Ostrava - Přívoz, Czech Republicc Institute of Physics, VŠB-Technical University of Ostrava, 17. listopadu 15, 708 33 Ostrava-Poruba, Czech Republicd Institute of Environmental Engineering, VŠB-Technical University of Ostrava, 17. listopadu 15, 708 33 Ostrava-Poruba, CzechRepublice Institute of clean technologies for mining and utilization of raw materials for energy use, VŠB-Technical University of Ostrava,17. listopadu 15, 708 33 Ostrava- Poruba, Czech Republic

AbstractThe article describes the results of an experimental research dealing with the use of industrial waste in the form of secondary rawmaterial - polyurethane foam after the end of its life cycle, as a 100% substitute of filler in restoration plaster with thermalinsulating effect. The article presents the formulas of restoration plaster and its properties. They are: mortar consistency, volumeweight, strength characteristics, thermal conductivity coefficient, coefficient of capillary water absorption, porosity and resistanceagainst salts. © (2014) Trans Tech Publications, Switzerland.

Author KeywordsPhysical and mechanical properties; Plaster; Recycling; Rigid polyurethane foam

Index KeywordsBinders, Plaster, Recycling, Restoration, Rigid foamed plastics, Thermal conductivity, Thermal insulating materials; Capillarywater absorption, Experimental research, Physical and mechanical properties, Rigid polyurethane foams, Secondary RawMaterials, Strength characteristics, Thermal conductivity coefficient, Use of industrial wastes; Strength of materials

References

Odpady a surovinová politika ČR. In: Odpadové fórum [online]. Praha: České ekologickémanažerské centrum, 2012 [cit. 2013-04-28]. Dostupné z

Václavík, V., Dvorský, T., Dirner, V., Daxner, J., Šťastný, M.(2012) Tehnički Vjesnik - Technical Gazette, 19 (3), pp. 665-672. ISSN 1330-3651

Václavík, V., Valíček, J., Dvorský, T., Hryniewicz, T., Rokosz, K., Harničárová, M., Kušnerová,M., Bendová, M.(2012) Rocznik Ochrony Środowiska, 14, pp. 96-106. ISSN 1506- 218X

Gutiérrez-González, S., Gadea, J., Rodríguez, A., Junco, C., Calderón, V.Lightweight plaster materials with enhanced thermal properties made withpolyurethane foam wastes(2012) Construction and Building Materials, 28 (1), pp. 653-658. DOI: http://dx.doi.org/10.1016/j.conbuildmat.2011.10.055


1 z 3 5. 11. 2014 11:59

Fraj, A.B., Kismi, M., Mounanga, P.Valorization of coarse rigid polyurethane foam waste in lightweight aggregate concrete(2010) Construction and Building Materials, 24 (6), pp. 1069-1077. DOI: http://dx.doi.org/10.1016/j.conbuildmat.2009.11.01

Václavík, V., Dirner, V., Dvorský, T., Daxner, J.The use of blast furnace slag(2012) Metallurgy, 51 (4), pp. 461-464. ISSN 0543-5846

Stevulova, N., Vaclavik, V., Junak, J., Grul, R., Bacikova, M.Utilization possibilities of selected wastekinds in building materials preparing(2008) SGEM 2008: Modern Management of Mineproducing, Geology and

Environmentalprotection, pp. 193-200. Sofia: SGEM

Svarla, J., Sisol, M., Botula, J., Kolesarova, M., Krinicka, I.The potential use of fly ash with a high content of unburned carbon in geopolymers(2011) Actageodynamicaetgeomaterialia, 7 (2), pp. 123-132. ISSN 1214-9705

Ondova, M., Stevulova, N.Benefitsofcoalflyashutilization in the area of a pavementbuilding(2011) ENVIRONMENTAL ENGINEERING, 1-3, pp. 1156-1159.

Junak, J., Stevulova, N.Potential of selected industrial wastes in civil engineering applications(2011) 11th International Multidisciplinary Scientific Geoconference (SGEM

2011), 3, pp. 567-572. Book Series: International Multidisciplinary Scientific GeoConference- SGEM

Knapčíková, L., Herzog, M.(2011) Kompozitné Materiály Na Báze Textílií Z Opotrebovaných Pneumatic. 1. Vyd - Prešov:

FVT TU, p. 166. ISBN 978-80-553-0697-1

Knapčíková, L., Husár, J., Herzog, M., Pešek, L.Testing of new composite materials based on fabric from used tires(2012) Chemické Listy, 106 (S), pp. 450-452. ISSN 0009-2770

Svoboda, A.L.Stavební Hmoty, 1. vyd. Bratislava: JAGA, 2007. ISBN 978-80-8076- 057-1

Filipi, P.Plasty. Skripta VŠB-TU Ostrava(2003) Vydalo Sdružení Požárního a Bezpečnostního Inženýrství, Ostrava, str. 48, ISBN 80-86634-13-2


2 z 3 5. 11. 2014 11:59





Methods of Test For Mortar For Masonry - Part 9: Determination of Workable Life and

Correction Time of Fresh Mortar, EN 1015-9

Methods of Test For Mortar For Masonry - Part 10: Determination of Dry Bulk Density of

Hardened Mortar, EN 1015-10

Methods of Test For Mortar For Masonry - Part 11: Determination of Flexural and Compressive

Strentgth of Hardened Mortar, EN 1015-11

WTA - Směrnice 2-2-91 Sanační Omítkové Systémy,

Methods of Test For Mortar For Masonry - Part 12: Determination of Adhesive Strength of

Hardened Rendering and Plastering Mortars On Substrates, EN 1015-12

Methods of Test For Mortar For Masonry - Part 18: Determination of Water Absorption

Coefficient Due to Capillarity Action of Hardened Mortar, EN 1015-18

Sponsors:Publisher: Trans Tech Publications

Conference name: 11th International Conference Binders and Materials 2013, ICBM 2013Conference date: 5 December 2013 through 5 December 2013Conference location: BrnoConference code: 103210

ISSN: 10226680ISBN: 9783038350262DOI: 10.4028/www.scientific.net/AMR.897.204Language of Original Document: EnglishAbbreviated Source Title: Adv. Mater. Res.Document Type: Conference PaperSource: Scopus


3 z 3 5. 11. 2014 11:59

Documents

Silarova, P., Pertile, E., Surovka, D.New medium heavy-based sorbent porosorb based on industrial waste

(2013) International Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management,

SGEM, pp. 401-408.

Institute of Environmental Engineering, VSB-Technical University of Ostrava, Czech Republic

Abstract

The theme of this article is concerned with the utilization of waste from grey cellular concrete production. This waste is crushedby swing-hammer mill and the final waste product is sanitary crushed material with grain size of 0.5 - 2 mm. This crushedmaterial was tested for sorption and neutralizing capacity. The results obtained were compared to those sorbents currently usedin practice. It has been shown that the new sorbent achieves the same level, in some cases higher, as usual sorbents. ©SGEM2013 All Rights Reserved by the International Multidisciplinary Scientific GeoConference SGEM.

Author Keywords

Cellular concrete; Sorbent; Waste

Index Keywords

Cellular concretes, Crushed materials, Grain size, Waste products; Concretes, Exhibitions, Sorption, Wastes; Sorbents

References

Václavík, V., Dvorský, T., Dirner, V., Daxner, J., Šťastný, M.Polyurethanefoam as aggregateforthermalinsulatingmortars and lightweightconcrete

(2012) TehnickiVjesnik, 19 (3), pp. 665-672. SSN 1330-3651

Václavík, V., Valíček, J., Dvorský, T., Hryniewicz, T., Rokosz, K., Harničárová, M., Kušnerová,M., Bendová, M.A methodofutilizationofpolyurethaneafterthe end ofitslifecycle

(2012) Rocznikochronasrodowiska, 14. ISSN 1506-218X

Václavík, V., Dirner, V., Dvorský, T., Daxner, J.(2012) Use Ofblastfurnaceslag. Metalurgija, 51 (4), pp. 461-464. ISSN 0543-5846

Stevulova, N., Vaclavik, V., Junak, J., Grul, R., Bacikova, M.Utilizationpossibilitiesofselectedwastekinds in buildingmaterialspreparing

(2008) SGEM 2008: Modern Management of Mineproducing, Geology and

Environmentalprotection, pp. 193-200. Sofia: SGEM

Svarla, J., Sisol, M., Botula, J., Kolesarova, M., Krinicka, I.(2011) The Potential Use of Fly Ash With a High Content of Unburned Carbon In

Geopolymers. Actageodynamicaetgeomaterialia, 7 (2), pp. 123-132. ISSN 1214-9705


1 z 2 5. 11. 2014 12:01

About Scopus


Customer Service


About Elsevier



Ondova, M., Stevulova, N.Benefitsofcoalflyashutilization in the area of a pavementbuilding

(2011) ENVIRONMENTAL ENGINEERING, 1-3, pp. 1156-1159.

Junak, J., Stevulova, N.Potential of selected industrial wastes in civil engineering applications

(2011) 11TH INTERNATIONAL MULTIDISCIPLINARY SCIENTIFIC GEOCONFERENCE

(SGEM 2011, 3, pp. 567-572. Book Series: International Multidisciplinary Scientific GeoConference-SGEM

ČasopisNebezpečnýnáklad, ISSN 1803-1579, čerpáno [online] 4/2013 z

Svoboda, L.(2005), p. 199. Stavebníhmoty; ISBN: 80-8076-007-1, vydáno, Vydavatelstviá JAGA GROUP, s. r.o.;, strana


Institute of Environmental Engineering, VSB-Technical University of OstravaCzech Republic

Conference name: 13th International Multidisciplinary Scientific Geoconference and EXPO, SGEM 2013Conference date: 16 June 2013 through 22 June 2013Conference location: AlbenaConference code: 102053

ISSN: 13142704ISBN: 9786197105032DOI: 10.5593/SGEM2013/BD4/S18.015Language of Original Document: EnglishAbbreviated Source Title: Int. Multidisciplinary Sci. Geoconf. Surveying Geology Mining Ecology Manage., SGEMDocument Type: Conference PaperSource: Scopus


2 z 2 5. 11. 2014 12:01

Documents

Kolská, Z.a , Kasálková, N.S.b , Siegel, J.b , Švorčík, V.b

Electrokinetic potential for characterization of nanosctructured solid flat surfaces

(2013) Journal of Nano Research, 25, pp. 31-39. Cited 1 time.

a Faculty of Science, J.E. Purkyně University, České mládeže 8, Ústínad Labem 40096, Czech Republicb Department of Solid State Engineering, Institute of Chemical Technology, Prague, Czech Republic

Abstract

Electrokinetic potential (zeta potential) is a characteristic parameter for description of the surface chemistry of solid flat materialsand it can be used for a fast analysis of materials modified by different chemical or physical methods. Due to its sensitivity, zetapotential is able to distinguish surface modified by coating with monolayers of various materials or nanostructures created afterplasma treatment. Also metal nanostructures deposited on surfaces can be characterized by zeta potential. It can also be usedfor isoelectric point determination of materials. We present data on zeta potential in 0.001 mol/dm3 KCl at constant pH≈7.0 andalso in pH range (2.5-7.0) for isoelectric point determination for pristine polymers PET, PTFE, PS, LDPE, HDPE, PLLA, PVF,PVDF, PMP and polyimides (Upilex R, Upilex S, Kapton). The zeta potential of selected polymers, modified by plasma and bychemical coatings (e.g. by biphenyldithiol or polyethyleneglycol) or by gold deposition was measured too. Zeta potentials of thesemodified materials were also studied to confirmation that electrokinetic analysis is acceptable method for their fast description. ©(2013) Trans Tech Publications, Switzerland.

Author Keywords

Cell adhesion and proliferation; Electrokinetic potential; Gold deposition; Plasma treatment; Polymers; Surface modification

Index Keywords

Electrokinetic analysis, Electrokinetic potentials, Gold deposition, Iso-electric points, Metal nanostructure, Modifiedmaterials, Plasma treatment, Pristine polymers; Cell adhesion, Characterization, Chemicalanalysis, Coatings, Deposition, Gold, Nanostructures, Plasma applications, Polyethyleneterephthalates, Polyimides, Polymers, Surface chemistry, Surface treatment, Surfaces; Zeta potential

References

Řezníčková, A., Kolská, Z., Hnatowicz, V., Stopka, P., Švorčík, V.Comparison of glow argon plasma-induced surface changes of thermoplastic polymers

(2011) Nucl. Instrum. Meth. B, 269, pp. 83-88.

Švorčík, V., Kolská, Z., Luxbacher, T., Mistrík, J.Properties of Au nano-layer sputtered on PET

(2010) Mater. Lett, 64, pp. 611-613.

Slepičková Kasálková, N., Slepička, P., Kolská, Z., Sajdl, P., Bačáková, L., Rimpelová, S.,Švorčík, V.Cell adhesion and proliferation on polyethylene grafted with Au nanoparticles(2012) Nucl. Instrum. Meth. B, 272, pp. 391-394.

Švorčík, V., Makajová, Z., Kasá lková-Slepičková, N., Kolská, Z., Bačá ková, L.Plasma-modified and polyethylene glycol-grafted polymers for potential tissue

engineering applications

(2012) J. Nanosci. Nanotechnol, 12, pp. 6665-6671.

Hiemenz, P., Rajagopalan, R.(1997) Principles of Colloid and Surface Chemistry, Marcel Dekker, Inc., New York


1 z 3 5. 11. 2014 12:02

Beattie, J.K.The intrinsic charge on hydrophobic microfluidic substrates

(2006) Lab. Chip, 6, pp. 1409-1411.

Kirby, B.J., Hasselbrink Jr., E.F.Zeta potential of microfludic substrates: 1. Theory, experimental techniques, and

effects on separation

(2004) Electrophoresis, 25, pp. 187-202.

Luxbacher, T., Bukšek, H., Petrinić, I., Pušić, T.Zeta potential determination of flat solid surfaces using a SurPASS electrokinetic

analyzer

(2009) Tekstil, 58, pp. 393-400.

Švorčík, V., Kolářová, K., Slepička, P., Macková, A., Hnatowicz, V.Modification of surface properties of high and low density polyethylene by Ar plasma

discharge

(2006) Polym Degr. Stab, 91, pp. 1219-1225.

Mikulíková, R., Moritz, S., Gumpenberger, T., Olbrich, M., Romanin, C., Bačáková, L., Švorčík,V., Heitz, J.Cell microarrays on photochemically modified polytetrafluorethylene

(2005) Biomaterials, 26, pp. 5572-5580.

Heitz, J., Švorčík, V., Bačáková, L., Ročková, K., Ratajová, E., Gumpenberger, T., Bauerle, D.,Romanin, C.Cell adhesion on polytetrafluoroethylene modified by UV-irradiation in an ammonia

atmosphere

(2003) J. Biomed. Mater. Res, 67 A, pp. 130-137.

Švorčík, V., Kasálková, N., Slepička, P., Záruba, K., Bačáková, L., Parízek, M., Ruml, T.,Macková, A.(2009) Nucl. Instrum. Meth. B, 267, pp. 1904-1910.

Řezníčková, A., Kolská, Z., Hnatowicz, V., Švorčík, V.Nano-structuring of PTFE surface by plasma treatment, etching, and sputtering with

gold

(2011) J. Nanopar. Res, 13, pp. 2929-2938.

Bacakova, L., Filova, E., Parízek, M., Ruml, T., Švorč ík, V.Control of cell adhesion, proliferation and differentiation on materials designed forbody implants

(2011) Biotechnol. Adv, 29, pp. 739-767.

Kolská, Z., Řezníčková, A., Švorčík, V.Surface characterization of polymer foils

(2012) E-Polymers, 83, pp. 1-13.

Siegel, J., Lyutakov, O., Rybka, V., Kolská, Z., Švorč ík, V.Properties of gold nanostructures sputtered on glass

(2011) Nanoscale Res. Lett, 6, pp. 96-104.


2 z 3 5. 11. 2014 12:02

About Scopus


Customer Service


About Elsevier



Švorčík, V., Řezníčková, A., Kolská, Z., Slepička, P., Hnatowicz, V.Variable surface properties of PTFE foils

(2010) E-Polymers, 133, pp. 1-5.

Škvarla, J., Luxbacher, T., Nagy, M., Sisol, M.Relationship of surface hydrophilicity, charge, and roughness of PET foils stimulated


(2010) ACS Appl. Mater. Inter, 2, pp. 2116-2127.

Kasálková, N., Makajová, Z., Parízek, M., Slepička, P., Kolárová, K., Bačáková, L., Hnatowicz,V., Švorčík, V.Cells adhesion and proliferation on plasma-treated and PEG-grafted PE

(2010) J. Adhes. Sci. Technol, 24, pp. 743-754.

Slepička, P., Kolská, Z., Náhlík, J., Hnatowicz, V., Švorčík, V.Properties of Au nanolayers on polyethyleneterephthalate and polytetrafluoroethylene

(2009) Surf. Interface Anal, 41, pp. 741-745.


Kolska Z.; Faculty of Science, J.E. Purkyně University, České mládeže 8, Ústínad Labem 40096, Czech Republic; email:[email protected]

ISSN: 16625250DOI: 10.4028/www.scientific.net/JNanoR.25.31Language of Original Document: EnglishAbbreviated Source Title: J. Nano. Res.Document Type: ArticleSource: Scopus


3 z 3 5. 11. 2014 12:02

Documents

Durdan, M., Kacur, J.Indirect temperatures measurement in the UCG process(2013) Proceedings of the 2013 14th International Carpathian Control Conference, ICCC 2013, art. no. 6560514, pp. 73-78.

Institute of Control and Informatization of Production Processes, Faculty BERG, Technical University of Košice, Košice, Slovakia

Abstract

The technology of the underground coal gasification (UCG) is still under development and provides alternative for conventionalunderground mining. UCG is the process, which can be attractive from environmental and economic aspect and is able to have awide utilization in the future. This technology is less expensive than conventional mining. For research and good analyze of thisprocess there was created the physical model of the gasifier, that simulate the conditions of the real coal-bed in geometricsimilarity. On created physical model was performed a several experiments represent a various underground conditions. In thegasification process the input is the coal (coal-bed) and oxidizer (mixture of the air and oxygen), which suitable combinationprovides the best conditions for gasification. One of the expected outputs from the coal gasification process is the hightemperature in the coal-bed, which enable running of the chemical reaction needed for the syngas generation. The control of thistemperature in the single places of the coal-bed would enable to control behavior of the chemical reactions so the burning queueproceeds. The measurement of the temperatures inside the coal-bed is still complicated because there is the high thermocouplesmortality in aggressively hot environment. For this reason is needed to use mathematic -physical apparatus for indirectmeasurement of these temperatures. In this contribution is presented proposal of the indirect temperature measurement structurein the coal-bed that was verified in the laboratory conditions on the experimental gasifier. © 2013 IEEE.

Author Keywords

indirect measurement; physical model; temperatures simulation; UCG

Index Keywords

Gasification process, Geometric similarity, Indirect measurements, Laboratory conditions, Physical model, Syn-gasgeneration, UCG, Underground coal gasification; Carbonization, Temperature measurement, Thermocouples; Coal deposits

References

Varga, A., Kizek, J., Lazi, L.Influence of flue gas recirculation on NOx and CO formation = Utjecaj recirkulacijeizgarnih plinova na tvorbu NOx i CO(2004) Strojarstvo, 46 (1-3), pp. 51-55.

Lazi J Varga, L., Kizek, J.Analysis of combustion characteristics in a aluminium melting furnace = Analizaprocesa izgaranja u pe i za taljenje aluminija(2005) Metalurgija, 44 (3), pp. 195-199.

Laciak, M., Ššofranko, M., Reviák, L.Application for designing of the technological line ?-PROTELIN = Aplikácia preprojektovanie technologickej linky-PROTELIN(2012) Minerální suroviny, (34), pp. 32-35.

Kostúr, K., Laciak, M.Model for indirect measurements of LD Steelmaking Process(2002) Metalurgija, 41 (2), pp. 113-116.

Michalíková, F., Šškvarla, J., Sisol, M., Krinická, I., Kolesárová, M.Treatment processes for utilization of high carbon fly ashes from combustion of black


1 z 3 5. 11. 2014 12:03

About ScopusWhat is Scopus

Customer ServiceHelp and Contact

About ElsevierAbout Elsevier

coal in thermal power plants = Technologie przeróbcze uszlachetniania, zawieraja cychczcci palne, popiolów lotnych z w gli kamiennych spalanych w elektrocieplowniach,?(2010) Inzynieria Mineralna, 11 (12), pp. 9-26. January

Laciak, M., Kostúr, K., Truchlý, M.The analysis of models for indirect measurement of surface temperatures in massivecharge(2008) Acta Montanistica Slovaca, 13 (1), pp. 94-99.

Kostúr, K.(2007) Underground Coal Gasification by Thermal Decomposition = Podzemné SplyovanieUhlia Termickým Rozkladom, APVV-0582-06, ? Research Report of the Project, TU Košice, BERG

Kostúr, K.(2008) Underground Coal Gasification by Thermal Decomposition = Podzemné SplyovanieUhlia Termickým Rozkladom, APVV-0582-06,? Research Report of the Project, TU Košice, BERG

Terpák, J., DorákThe processes of the heat transfer = Procesy prenosu(2001) TU Ko Šice, Faculty BERG,

Kostúr, K.Simulation models of the heat aggregates = Simula né modely tepelných agregátov(1997) ŠŠtroffek, Košice,

Komorová, Imriš, I.Thermodynamics in metallurgy = Termodynamika v hutníctve(1992) Bratislava Alfa, p. 289.

Pástor, M., Varga, A., Budayová, M.Kinetic of particles gasifying at fluid bed,?(2009) Monuments of Old Metallurgy As Heritage of European Culture, pp. 95-98.

Correspondence AddressInstitute of Control and Informatization of Production Processes, Faculty BERG, Technical University of Košice, Košice, Slovakia

Conference name: 2013 14th International Carpathian Control Conference, ICCC 2013Conference date: 26 May 2013 through 29 May 2013Conference location: RytroConference code: 98673

ISBN: 9781467344890DOI: 10.1109/CarpathianCC.2013.6560514Language of Original Document: EnglishAbbreviated Source Title: Proc. Int. Carpathian Control Conf., ICCCDocument Type: Conference PaperSource: Scopus


2 z 3 5. 11. 2014 12:03

Content coverage Live chat Terms and ConditionsPrivacy Policy



3 z 3 5. 11. 2014 12:03

Documents

Skvarekova, E., Kozakova, L.Brown coal and lignite issues from the perspective of sustainable development in slovakia [Rola wȩ gla brunatnego wzrównowżonym rozwoju słowacji]

(2012) Gospodarka Surowcami Mineralnymi / Mineral Resources Management, 28 (2), pp. 31-42. Cited 2 times.

Technical University of Kosice, Faculty of Mining, Ecology, Process Control and Geotechnology, Slovakia

AbstractThis paper presents the situation of coal mining in Slovakia, focusing on the social-political aspects and environmental aspects ofits sustainable development. In recent years, the mining of lignite and brown coal in Slovakia has been closely linked to theproduction of electricity and heat in the Novaky power plant. Domestic brown coal production covered more than three quarters ofdemand in the Slovak Republic in the last few years. The sustainability of coal mining in the coming years in Slovakia is closelyassociated with raw materials reserves, new mining technologies, the development of the Novaky power plant, and thegovernment's commitments to national economic interests through securing the energy supply or state aid. Of course, of thesefactors must be considered in the context of international obligations, such as those related to climate and environment,particularly air protection. The three most important Slovak brown coal deposits are located in the Upper Nitra Basin. Thisterritory includes areas in the 5 th and 4 th degrees of environmental quality, signifying a disturbed and very disturbedenvironment. Since coal is expected to remain the dominant fuel for electricity generation araund the world, and in particular formany of the countries of Central and Eastern Europe, it is necessary to create conditions for the environmental sustainability ofcoal mining in the coming years within the context of international obligations. Both the security and the stability of the electricitynetwork in Slovakia and maintaining employment levels in the Upper Nitra region play important roles in this discussion.Underground coal gasification (UCG) is a newmining technology and a technology for gas recovery in situ. A comprehensiveevaluation of the impacts of underground coal gasification was carried out in addition to summarization of the expected impacts interms of the significance and distribution of the time period. Based on a comprehensive assessment of the proposed action, itcan be stated that it could bring a socially unacceptable risk to the area, specifically the significant impairment of health or theenvironment (groundwater and nearby hot springs in Bojnice). The implementation of operations could affect the population'shealth, since the partition is placed in close proximity to residential areas.

Author KeywordsCoal mining; Employment; Environmental aspects of sustainable development; Social-political aspects of sustainabledevelopment

References

Analysis of the functioning of state support of mining(2011) Ministry of Economy, Analysis of the functioning, May 2011

(2011) Analysis of the Number of Registered Exclusive Deposits of Energy Resources In the

Inventory Balance of Minerals Based On their Real Usefulness In the Longer Term, Analysis of the number, Government Resolution, May, 2011

Borys, T.Sustainable Development - How to Recognize Integrated Order(2011) Problems of Sustainable Development, 6 (2), pp. 75-81. In:] Problemy ekorozwoju

Fazekasova, D.Trvalo udrzatelne vyuzivanie pody - vymedzenie a hodnotenie indikatorov a parametrovvyvoja pody(2003) FHPV PU, Presov, p. 76. ISBN 80-8068-228-3


1 z 3 6. 11. 2014 9:13

Gałuszka, A., Migaszewski, Z.Problems of Sustainable Use of Mineral Resources(2009) Problems of Sustainable Development, 4 (1), pp. 123-130. In:] Problemy ekorozwoju

Ilie, E.(2010) Coal Market is More Stable In Western Europe,

Jablonska, J., Timcak, G.Sustainable tourism development possibilities in Eastern Slovakia(2006) Nitra: Slovenska Polnohospodarska Univerzita, pp. 590-592. In:] Regiony - vidiek - zivotne prostredie 2006. 1. cast, ISBN 8080697094

Kovacik, M.Je Lepsie Dotovat Domacich Banikov, Ako Kupovat Plyn Z Ruska(2010) It is Better to Subsidize Domestic Miners Than to Buy Gas From Russia, 25.1.2010

Lumnitzer, E., Kralikova, R.Risk factors in the environment(2002) Acta Mechanica Slovaca. Roc, (2), pp. 259-264. ISSN 1335-2393

Michalikova, F., Kosuth, M., Skvarla, J., Zelenak, F., Sisol, M.Properties of lignite fly ash from coal combustion in thermal power Eno Novaky(2008) Zpravodaj Hnede Uhli, 2, pp. 33-41. ISSN 1213-1660

(2009) Study of Quarry Kosariska Cigel, 2009, Environmental Impact of Assessment, Study of quarry, Slovak Minerals Yearbook 2010 - Slovak Minerals Yearbook 2010, Statisticaldata to 2009, Ministry of the Environment of the Slovak Republic, State Geological Institute ofDionyz Stur, Bratislava

Sidorova, M., Wittenberger, G.Clean coal and gasification technology: How does it works?(2006) Acta Montanistica Slovaca. Roc, 11, pp. 162-165. 1 mimoriadne 2006, ISSN 1335-1788

Sivakova, A.Lignite mining is justified(2011) Hornonitrianske Bane Prievidza,

Skvarekova, E., Bakalar, T.(2011) Impact of Gas Extraction From Coal Deposits On the Environment, 1, pp. 795-800. In:] SGEM, 11th International Multidisciplinary Scientific GeoConference, Sofia, Bulgaria

(2008) State of the Environment Report Slovak Republic, 2008, Slovak Environmental

Agency, State of the, UNECE 2011 - UNECE 2011 Committee Objectives


2 z 3 6. 11. 2014 9:13





Zacher, L.W.Dimensions of Ecological Discourse - Overview of Problems and Selected Literature(2011) Problems of Sustainable Development, 6 (2), pp. 83-92. In:] Problemy ekorozwoju

Zelenak, S.Teoreticke Aspekty Vyplnovania Zavalovych Dutin Pri Stenovani(2003) Theoretical Aspects of Cavities Filling In the Longwall, DDP, F BERG, TU v Kosiciach

Wittenberger, G., Pinka, J.Advanced technologies and ecological materials for buildings heating by energy fromthe earth using a deep well pump(2009) Situacia V Ekologicky Zatazenych Regionoch Slovenska a Strednej

Europy, pp. 159-162. Kosice: Ustav geotechniky SAV, ISBN 9788097003418


Skvarekova E.; Technical University of Kosice, Faculty of Mining, Ecology, Process Control and GeotechnologySlovakia; email:[email protected]

ISSN: 08600953DOI: 10.2478/v10269-012-0017-zLanguage of Original Document: English; PolishAbbreviated Source Title: Gospodarka Surowcami Mineral. Mineral Res. Manage.Document Type: ArticleSource: Scopus


3 z 3 6. 11. 2014 9:13

Documents

Lapčík Jr., L., Fraštík, M., Lapčíková, B.Impinging jet study of the deposition of colloidal particles on modified polycarbonate and poly(ethylene terephthalate)

surfaces

(2012) International Journal of Heat and Mass Transfer, 55 (5-6), pp. 1513-1518. Cited 1 time.

Centre of Polymer Systems, Faculty of Technology, Tomas Bata University in Zlin, nám. T.G. Masaryka 5555, 760 05 Zlín, CzechRepublic

Abstract

Main focus of this study was on characterization of surface properties of virgin and 1,2-dipalmitoyl-sn-glycero-3-phosphocholine(DPPC) phospholipid layer coated poly(ethylene terephthalate) (PET) and polycarbonate (PC) planar articles. Surface propertieswere followed measuring static contact angles of wetting by means of sessile drop method and deposition of negativepolystyrene (PS) colloidal particles followed by impinging jet method at defined flow regimes. It was found that phospholipidcoating of both studied samples (PET, PC) let to the vigorous increase of the surface free energy. For coated samples major partof the surface free energy was dominated by polar component in contrast to the non-treated materials. Here the dispersivecomponent was dominating. Results of the deposition experiments of polystyrene particles of 3 µm diameter correspond withtrends obtained by contact angle measurements, i.e. the surface treated materials exhibited higher surface activity reflected inincreased particle deposition rates. Simultaneously there was confirmed the fact, that with increasing magnitude of the Reynoldsnumber of the dispersion flux the higher deposition rates were observed. © 2011 Elsevier Ltd. All rights reserved.

Author Keywords

Contact angles of wetting; Deposition kinetics; Impinging jet; Phospholipid layer; Poly(ethylene terephthalate); Polycarbonate; Polystyrene particles

Index Keywords

1 ,2-dipalmitoyl-sn-glycero-3-phosphocholine, Coated sample, Colloidal particle, Deposition experiments, Depositionkinetics, Dispersive components, Flow regimes, Impinging jet, Particle depositions, Phospholipid-coating, Polarcomponents, Polystyrene particle, Polystyrene particles, Sessile drop method, Static contact angle, Surface activities, Surfacefree energy, Surface-treated materials; Characterization, Coated materials, Colloids, Contact angle, Deposition, Depositionrates, Ethylene, Free energy, Phospholipids, Polycarbonates, Polyethylene terephthalates, Polystyrenes, Reynoldsnumber, Surface properties, Wetting; Surfaces

References

Van De Ven, T.G.M.(1989) Colloidal Hydrodynamics, Academic Press London, San Diego

Dbroś, T., Van De Ven, T.G.M.A direct method for studying particle deposition onto solid surfaces

(1983) Colloid Polym. Sci., 261 (8), pp. 694-707.

Warszynski, P.Coupling of hydrodynamic and electric interactions in adsorption of colloidal particles

(2000) Advances in Colloid and Interface Science, 84 (1), pp. 47-142. DOI 10.1016/S0001-8686(99)00015-9

Kamiti, M., Van De Ven, T.G.M.Impinging jet studies of the kinetics of deposition and dissolution of calcium carbonate

particles

(1995) Colloids Surfaces A: Physicochem. Eng. Aspects, 100 (1), pp. 117-129.


1 z 4 6. 11. 2014 9:13

Goldman, A.J., Cox, R.G., Brenner, H.Slow viscous motion of a sphere parallel to a plane wall - I motion through a quiescent

fluid

(1967) Chem. Eng. Sci., 22 (4), p. 653.

Van De Ven, T.G.M., Kelemen, S.J.Characterizing polymers with an impinging jet

(1996) Journal of Colloid and Interface Science, 181 (1), pp. 118-123. DOI 10.1006/jcis.1996.0362

Dbroś, T., Van De Ven, T.G.M.Kinetics of coating by colloidal particles

(1982) J. Colloid Interface Sci., 89 (1), pp. 232-244.

Adamczyk, Z., Warszynski, P., Szyk-Warszynska, L., Weronski, P.X.Role of convection in particle deposition at solid surfaces

(2000) Colloids and Surfaces A: Physicochemical and Engineering

Aspects, 165 (1-3), pp. 157-187. DOI 10.1016/S0927-7757(99)00416-1, PII S0927775799004161

Adamczyk, Z., Siwek, B., Zembala, M., Weroński, P.Kinetics of localized adsorption of colloid particles

(1992) Langmuir, 8 (11), pp. 2605-2610.

Kamiti, M., Dbroś, T., Van De Ven, T.G.M.Kinetics of surface coagulation(1995) J. Colloid Interface Sci., 172 (2), pp. 459-466.

Lapčík, L., Alince, B., Van De Ven, T.G.M.(1995) J. Pulp Paper Sci., 21 (1), pp. 19-24.

Van De Ven, T.G.M., Warszyński, P., Wu, X., Dbroś, T.Colloidal Particle Scattering: A New Method to Measure Surface Forces

(1994) Langmuir, 10 (9), pp. 3046-3056.

Warszynski, P., Wu, X., Van De Ven, T.G.M.Electrokinetic lift force for a charged particle moving near a charged wall - A modified

theory and experiment

(1998) Colloids and Surfaces A: Physicochemical and Engineering

Aspects, 140 (1-3), pp. 183-198. DOI 10.1016/S0927-7757(97)00277-X, PII S092777579700277X

Kamiti, M., Van De Ven, T.G.M.Measurement of spring constants of polyacrylamide chains bridging particles to a solid

surface

(1996) Macromolecules, 29 (4), pp. 1191-1194.

Adamczyk, Z., Siwek, B., Warszynski, P., Musial, E.Kinetics of particle deposition in the radial impinging-jet cell

(2001) Journal of Colloid and Interface Science, 242 (1), pp. 14-24. DOI 10.1006/jcis.2001.7767


2 z 4 6. 11. 2014 9:13

Adamczyk, Z.(2006) Particles at Interfaces. Interactions. Deposition, Structure, Academic Press London

Lapčík Jr., L., Lapčík, L., De Smedt, S., Demeester, J., Chabreček, P.Hyaluronan: Preparation, structure, properties, and applications

(1998) Chem. Rev., 98 (8), pp. 2663-2684.

Kwok, D.Y., Li, D., Neumann, A.W.Evaluation of the Lifshitz-van der Waals/acid-base approach to determine interfacial

tensions

(1994) Langmuir, 10 (4), p. 1323.

Lapčík Jr., L., Benešová, K., Lapčík, L., De Smedt, S., Lapčíková, B.Chemical modification of hyaluronic acid: Alkylation

(2010) Int. J. Polymer Analysis Characterization, 15 (8), pp. 486-496.

Lapčík, L., Kuběna, K., Galatík, A., Kellö, V.(1990) General Physiol. Biophys., 9 (3), pp. 419-429.

Liedermann, K., Lapčík, L.(1996) Chem. Papers, 50 (4), pp. 218-223.

Lapcik Jr., L., Schurz, J.Photochemical degradation of hyaluronic acid by singlet oxygen

(1991) Colloid and Polymer Science, 269 (6), pp. 633-635.

Argyropoulos, D.S., Morin, F., Lapčík, L.Magnetic field and temperature effects on the solid state proton spin-lattice relaxation

time measurements of wood and pulps

(1995) Holzforschung, 49 (2), pp. 115-118.

Škvarla, J., Luxbacher, T., Nagy, M., Sisol, M.Relationship of surface hydrophilicity, charge, and roughness of PET foils stimulated


(2010) Appl. Materials Interfaces, 2 (7), pp. 2116-2127.

Jurak, M., Chibowski, E.Zeta potential and surface free energy changes of solid-supported phospholipid (DPPC)

layers caused by the enzyme phospholipase A <sub>2</sub> (PLA <sub>2</sub>)

(2009) Adsorption, 15 (2), pp. 211-219.

Jurak, M., Chibowski, E.Wettability and topography of phospholipid DPPC multilayers deposited by

spin-coating on glass, silicon, and mica slides

(2007) Langmuir, 23 (20), pp. 10156-10163. DOI 10.1021/la701220t


Lapcik Jr. L.; Centre of Polymer Systems, Faculty of Technology, Tomas Bata University in Zlin, nám. T.G. Masaryka 5555, 76005 Zlín, Czech Republic; email: [email protected]


3 z 4 6. 11. 2014 9:13

About Scopus


Customer Service


About Elsevier



ISSN: 00179310CODEN: IJHMADOI: 10.1016/j.ijheatmasstransfer.2011.11.002Language of Original Document: EnglishAbbreviated Source Title: Int. J. Heat Mass Transf.Document Type: ArticleSource: Scopus


4 z 4 6. 11. 2014 9:13

Documents

Brezáni, I., Zeleňák, F.MATLAB real-time data acquisition for laboratory froth flotation automation

(2011) Acta Montanistica Slovaca, 16 (2), pp. 176-183.

Technical University of Košice, BERG Faculty, Institute of montanneous sciences and environmental protection, ParkKomenského 19, 043 84 Košice, Slovakia

Abstract

In this paper analog input/output signals are used to control laboratory froth flotation machine using industrial panel PC. Dataacquisition is provided by two Advantech PCI cards, while flotation control is based on connection of adjustable frequency drivefurther connected to AC motor for agitation control, mass flow controller for air flow control, pH and temperature transmitters withaccording probes for pH and temperature logging respectively. Process control is provided by graphical user interfaceprogrammed in MATLAB. This practical engineering design allows researchers to set parameter values prior to flotation test aswell as log and save measured values for further processing.

Author Keywords

Automation; Data acquisition; Froth flotation; MATLAB; Signal processing

References

(2011) Art. Encyclopedia Britannica Online, Flotation separation cell, Web. 19 Sep

Yianatos, J.B.Fluid flow and kinetic modelling in flotation related processes: Columns and

mechanically agitated cells - a review

(2007) Chemical Engineering Research and Design, 85 (12), pp. 1591-1603.

Laurila, H., Karesvuori, J., Tiili, O.Strategies for instrumentation and control of flotation circuits

(2002) Mineral Processing Plant Design, Practice and Control, 1, pp. 2174-2195.

Shean, B.J., Cilliers, J.J.A review of froth flotation control

(2011) International Journal of Mineral Processing, 100 (3-4), pp. 57-71.

Villeneuve, J., Guillaneau, J.-C., Durance, M.-V.Flotation modelling: A wide range of solutions for solving industrial problems

(1995) Minerals Engineering, 8 (4-5), pp. 409-420.

Gupta, A., Yan, D.S.(2006) Flotation, Mineral Processing Design and Operation, pp. 555-603. Elsevier Science, Amsterdam

(2006) USIM PAC Unit Operation Model Guide, Technical Manual, pp. 195-196. Caspeo, Version 3.1.1.0

Sisol, M.(2006) Flotation Separation of Plastics (in Slovak), Dissertation Thesis, Technical University of Košice


1 z 2 5. 11. 2014 12:06

About Scopus


Customer Service


About Elsevier



Brezáni, I.(2011) Laboratory Froth Flotation Machine Automation GUI, Available online


Brezani I.; Technical University of Košice, BERG Faculty, Institute of montanneous sciences and environmental protection, ParkKomenského 19, 043 84 Košice, Slovakia; email: [email protected]

ISSN: 13351788Language of Original Document: EnglishAbbreviated Source Title: Acta Montanistica SlovacaDocument Type: ArticleSource: Scopus


2 z 2 5. 11. 2014 12:06

Documents

Bestová, I.a , Heviánková, S.a , Zechner, M.b

Occurrence and removal of manganese from acid mine water [Wystȩpowanie manganu w wodzie kopalnianej oraz jego

usuwanie](2011) Inzynieria Mineralna, 12 (2), pp. 23-31.

a Institute of Environmental Engineering, Faculty of Mining and Geology, VŠB - Technical University Ostrava, 17.listopadu 15,708 33 Ostrava - Poruba, Czech Republicb Sokolov Coal, Legal Successor, a.s., Staré náměstí 69, 356 01 Sokolov, Czech Republic

Abstract

Apart from a high concentration of iron, mine water can also contain a higher concentration of manganese. Extraordinarily highconcentrations can be found in acid waters from the surroundings of ore deposits, e.g. the water from the sulfitic ore deposits inSmolník contain up to 40 mg.l-1 of manganese. The legislation ordains discharge of water into surface water with a maximumconcentration of manganese of 1 mg.l-1, and therefore it is vital to reduce the content of manganese in the mine water to apermissible value. Within the research work, a variety of demanganization methods were tested. In conclusion of the paper, so farmost optimal method of manganese removal from acid mine water is suggested.

Author KeywordsDemanganization; Manganese occurrence; Mine water

References

Pitter, P.(1999) Hydrochemie, 2nd edition, Prague, VŠCHT, ISBN 80-03-00525-6

Pitter, P., Tuček, F., Chudoba, J., Žáček, L.(1983) Laboratorní Metody V Technologii Vody, Prague

(1984) Chemický a Fyzikální Rozbor Odpadních Vod, Rok vydání, ČSN 83 05 40

Kusnierova, M., Fecko, P., Cablik, V., Pectova, I., Mucha, N.Extracting unburnt coal from black coal fly ash(2007) 2007 NSTI Nanotechnology Conference and Trade Show - NSTI Nanotech 2007,

Technical Proceedings, 4, pp. 628-631. 2007 NSTI Nanotechnology Conference and Trade Show - NSTI Nanotech 2007, TechnicalProceedings

Jacko, V., Michalíková, F.Possibilities of utilization of black coal ash from Energetics of U. S. Steel Kosice(original in Slovak language: Moznosti zuzitkovania ciernouholného popolceka zenergetiky U. S. Steel Kosice(2005) Acta Montanistica Slovaca, 10 (1), pp. 209-213. ISSN 1335-1788

Kušnierová, M., Praščáková, M., Čablik, V., Fečko, P.Odpady energetyczne jako substytut niemetalicznych surowców pierwotnych


1 z 2 5. 11. 2014 12:07





(2011) Journal of the Polish Mineral Engineering Society, (1-27), pp. 73-78. ISSN 1640-4920

Michalíková, F., Škvarla, J., Sisol, M., Krinická, I., Kolesárová, M.Technologie przeróbcze uszlachetniania, zawieraja̧cych czȩści palne, popiołów lotnychz wȩgli kamiennych spalanych w elektrocieptowniach(2010) Inżynieria Mineralna z, 1-2 (25-26), pp. s9-26. Wyd. Polskiego Towarzystwa Przeróbki Kopalin, Kraków, ISSN 1640-4920

Correspondence AddressBestova I.; Institute of Environmental Engineering, Faculty of Mining and Geology, VŠB - Technical University Ostrava,17.listopadu 15, 708 33 Ostrava - Poruba, Czech Republic; email: [email protected]

ISSN: 16404920Language of Original Document: Polish; EnglishAbbreviated Source Title: Inzynieria MineralnaDocument Type: ArticleSource: Scopus


2 z 2 5. 11. 2014 12:07

A., Klauk, H. Someya, T. -...

Documents

Transcript of A., Klauk, H. Someya, T. -...