6Sigma Naval Architecture & Offshore Engineering (Pty) Ltd

6Sigma Naval Architecture & Offshore Engineering (Pty) Ltd.

Alkmaar Road, Sturrock Dock,

Table Bay Harbour, Cape Town,

South Africa (HQ)

Tel: +27 21 447 1226

www.6s.co.za

info@6s.co.za

Ship Design Capabilities for Production Engineering

Full ship design is possible at 6Sigma. Using state-of-the-art ship production software all phases of design are possible:

Conceptual, basic, preliminary, detailed and production design

Current ship design possibilities

(Software used: SSI ShipConstructor)

� Fast attack, Patrol and similar vessels

� Fire Fighting Vessel

� Offshore—Drilling Ships

� Anchor handlers

� Offshore supply

� Ferry Boats

� Landing Craft

� DP vessels

� Tugs

� Barges

� Luxury Yachts

Detailed Engineering of Hull Structure and Appendices

� Frames, Sections and Deck drawings

� Detailed drawings for single and double curved hull plating

� Bending templates for forming of the shaped plate parts

� Posnumbering, lofting and nesting of plate and profile parts

� Partlists

� Cuttinglists for profiles including nesting of profiles, brackets

etc.

� Nestings in dxf or any requested format

� Counter foundations below decks

� Anchor pockets in fore- and aft ship (including the design)

� Bowthruster scallop

� Bilge keels

� Outer as well as inner bulwarks on main and forecastle deck

� Fender and other supports

Detailed Engineering of Superstructure

Standard profiles are used (T-bar, flat-bar, etc.)

� Counter foundations below decks

� Outer as well as inner bulwarks

� Canopies

� Bended plates as far as necessary for the ship construction

Detailed Engineering of Small Steel

� Floor supports

� Steps, Stairs

� Floating floors and related considering vibrations

� Furniture that integrated in the ships construction

Weight Control throughout design

(Software used: ShipWeight)

� Floating floors and related considering vibrations

� Furniture that integrated Weight and centre of gravity is calcu-

lated for each block section

� Weight control documented and provided as needed

Marine Engineering Drawings of Engine Room

� Arrangement Drawings

� Propulsion systems

� Funnel arrangement and

� Pipeline drawings e.g. Bilge lines, Fire-fighting lines, cooling

water lines, lubrication oil lines, dirty oil lines, fuel oil lines, hydraulic lines, working air lines, exhaust gas lines, sewage lines (unit and transfer)

� Drawings of all piping outside engine room for bilge suctions,

ballast fill/ suction lines (including sounding & de-aeration), fire-main and deck wash with branches

� Pipe Spools, production Information of all pipe systems and

fittings

� Sounding and de-aeration pipes and pipelines to bunker station

� Drawings of all piping outside engine room and technical room

for sewage treatment and transfer, tank connections and piping inside all waste water tanks, sounding and de-aeration pipes

� Drawings of all tank connections and piping inside tanks for

Lube oil, hydraulic oil, dirty oil, bilge water, waste fuel oil. Piping outside engine room to filling stations, sounding and de-aeration pipes

Customer review 3D models

� The customer is provided with the Navisworks model through-

out the project for comments or requests.

www.6S.co.za

Copyright © 2017, 6Sigma Naval Architecture & Offshore Engineering (Pty) Ltd., All rights Reserved

6Sigma Naval Architecture & Offshore Engineering (Pty) Ltd. has been found to conform to the Quality Management System

standard: ISO 9001:2015 for Engineering design for ship building, ship and rig repair, offshore engineering, project

management and subcontracting of manufacturing. (EA Sector: 20)

Design Portfolio

6Sigma Naval Architects and Offshore Engineering Pty Ltd, is a proud distributor and trainer of SSI ShipConstructor, Bentley Maxsurf, Ship-

Weight, CostFact and HydroComp. With our extensive network via our partners we vow to find 99% of all requested designs (class approved

packages) and take that into production engineering. Alternatively we can assist with any customer requirement from Concept design phase

to completion.

Type LOA Completed Phase

Barge - 100 Ton 20.8 Production Ready

Crew Boat (Aluminium) 30.0 Production Ready

Crew Boat (Aluminium) 33.0 Production Ready

Fast Landing Craft 20.9 Production Ready

Ferry Barge/ Barge - 10 Ton 18.3 Production Ready

Ferry Boat 12.0 Production Ready

Ferry Boat - 7 Ton 14.2 Production Ready

Fire Fighting Vessel 14.9 Production Ready

Fishing—Purse Seiner Trawler Request Production Ready

Landing Craft 26.0 Production Ready

Mooring Launch 13.0 Production Ready

Offshore—AHT DP2 Request Production Ready

Offshore—Drilling Ship Request Production Ready

Offshore—OSV Request Production Ready

Patrol—Coastal Surveillance Vessel 24.3 Production Ready

Patrol—Coastal Surveillance Vessel 24.3 Production Ready

Patrol—Fast Patrol Vessel 35.0 Production Ready

Patrol—Fast Patrol Vessel 42.2 Production Ready

Patrol—Ultra Fast Attack Vessel 24.4 Production Ready

Pilot Launch 17.0 Production Ready

Sea Going Launch - 150 People 30.0 Production Ready

Survey Boat 13.5 Production Ready

Tug Boat – 10 Ton Bollard Pull 23.4 Production Ready

Tug Boat - 20 Ton Bollard Pull 30.5 Production Ready

Tug Boat – 35 Ton Bollard Pull 40.0 Production Ready

Tug Boat – 45 Ton Bollard Pull 32.0 Production Ready

Tug Boat – 58 Ton Bollard Pull 35.0 Production Ready

Tug Boat – 65 Ton Bollard Pull 34.5 Production Ready

Tug Boat – 65 Ton Bollard Pull 34.5 Production Ready

www.6S.co.za

Copyright © 2017, 6Sigma Naval Architecture & Offshore Engineering (Pty) Ltd., All rights Reserved

6Sigma Naval Architecture & Offshore Engineering (Pty) Ltd. has been found to conform to the Quality Management System standard: ISO 9001:2015 for Engineering design for ship building, ship and rig repair, offshore engineering, project management and subcontracting of manufacturing. (EA Sector: 20)