636 - SPS Roof and Floor Draining Systems · 636 6shfldolw\ 3oxpelqj 6xssolhv 3w\ /wg $ & 1...
Transcript of 636 - SPS Roof and Floor Draining Systems · 636 6shfldolw\ 3oxpelqj 6xssolhv 3w\ /wg $ & 1...
SPS Speciality Plumbing Supplies Pty LtdA.C.N. 001 543 406
Addresses: Postal: PO Box 159 - Killara - NSW - 2071 Store: Unit 9L - 175 Lower Gibbes Street - Chatswood NSW 2067
Telephone (02) 9417 1900 Fax (02) 9417 0108 e-mail: [email protected]
PRODUCT CATALOG – REVISION 5
All SPS drains have been designed in Australia for Australian conditions and for Australian construction methods.
CONTENTS:
Section 1: Rainwater Outlets (“RWOs”)
Section 2: Domestic, Push-in and Retro-fit Drains
Section 3: Vari-level Drains - Vertical Outlets
Section 4: Vari-level Drains - Balcony & Side Outlets
Section 5: Vinyl Floor Wastes
Section 6: Basket Trap Floor Wastes
Section 7: Cleanouts - Inspection Points - Boundary Traps
Section 8: Security Drains
Section 9: Specials / Miscellaneous
Appendix: Flow Rate Information
Disclaimer:
All information contained in this catalogue is current as at 1 July 2017. SPS reserves the right to change product specifications - designs - components or associated services at any time without notice. The information contained in this catalogue does not form part of the terms of any contract of sale or constitute the description of any product or service supplied by SPS. Prior to purchasing or specifying - please contact SPS for any updates or modifications to current products or services. These drawings are for illustrative purposes only and are not to scale.
SECTION 1 Rainwater Outlets (RWO’s)
1.01
1.02
1.03
1.04
1.05
1.06
1.07
1.08
1.09
1.10
1.11
1.12
1.13
Truflo vertical – All-purpose RWO
Truflo vertical – Class D Flat Grate
Truflo vertical – Flat Grate & Membrane Clamp
Truflo vertical – Dome Grate & Membrane Clamp
Truflo vertical – Planter Box Assembly
Truflo 90° – Class D Flat Grate
Truflo 90° – Flat Grate & Membrane Clamp
Truflo 90°– Dome Grate & Membrane Clamp
Truflo 90° – Planter Box Assembly
Superflo – Class D Flat Grate
Superflo – Flat or Dome Grate & Membrane Clamp
“Shallow-flo” Push-in RWOs (USE WITH CAUTION)
Parapet Drain
To suit pipe (mm):
80, 100 & 150
80, 100 & 150
80, 100 & 150
80, 100 & 150
80, 100 & 150
80 & 100
80 & 100
80 & 100
80 & 100
150
150
100
50, 80 & 100
100Ø Socket
BA
N.B.
C
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
If a 100mm or 150mm Truflo RWO body is cast into the slab, it can be adapted forthe following 5 applications:
The SPS All-Purpose "Truflo" RWO Body
D
1.
2.
260
260
A
150100
N.B
240
240
B110
160
C
Integral puddleflange withweep holes 4 xplaces
3.
4.
5.
100mm
100mm BSP -Lowered position
With Class D flat grate,for non-waterproofedslabs (eg car parkdecks).
With flat grate andmembrane ring, formembraned slabs(eg roof decks &some plant rooms).
90
98D
2828E F
3745
25
25G
G
F
E
1.01
With 100mm or150mm reversibleclamping collar, forvari-level floor drains.
With dome grate andmembrane ring, forroof slabs (note:optional gravel guardpartially illustrated).
With special PVC"planter box" fitting,for planter boxes.
150mm BSP -Raised position
Dimensions (mm)
Dimensions (mm)
SPS Truflo 100mm & 150mm RWOwith Class D Heavy-Duty Flat Grate
Load-tested to Class D of AS3996-2006
A
C
N.B.
B
Speciality Plumbing Supplies Pty Ltd*For flow rate data please refer to appendix.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Specification codes:TIA100F (100mm CI body, galvanised flat grate)TIA150F (150mm CI body, galvanised flat grate)TBS100F (100mm bronze body, 316SS flat grate)TBS150F (150mm bronze body, 316SS flat grate)- for 80mm outlet, use "100/80" instead of "100"
Integral puddleflange withweep holes 4 xplaces
D
Optional tailpiececonnector (suffix "E")
Structural slab
Flat grate in heavy duty,hot-dipped galvanisedmid-carbon steel or 316stainless steel
Optional couplingconnector (suffix "P")
F
G
E
1.02
Suggested applications:Car park decksPlant rooms
S P S
Optional high-heelfriendly pattern (6mmgaps) use suffix -F
25
25
G
4537
28
28
103151
106
86
260
260
100150
240
240
N.B DA CB E F10680 260 82240 28 45 25
Suggested application:Membraned floors orroofs with no further topping,eg planter boxes, plantrooms, roof decks.
S P S
Membrane ring fastens to bodyindependently of grate to allow accessto sump without breaking membraneseal.
Specification codes:TIA100F2 (CI body, aluminium flat grate & membrane ring)TIB100F2 (CI body, bronze flat grate & membrane ring)TBA100F2 (all-bronze assembly)- for 80mm outlet, use "100/80" instead of "100"- for 150mm outlet, use "150" instead of "100"
SPS Truflo 80, 100 & 150mm RWOwith Flat Grate & Membrane Clamp
E
Membrane
25
25
G
C
N.B.
Structural slab
D
E-series PVC in-pipeadapter (suffix "E")
4537
28
28
103151
106
86
260
260
100150
240
240
N.B DA CB E F
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
A
G
Optional couplingconnector (suffix "P")
F
B
Integral puddleflange withweep holes 4 xplaces
1.03
Load Class A - AS 3996-2006
10680 260 82240 28 45 25
*For flow rate data please refer to appendix.
Dimensions (mm)
Dimensions (mm)
Integral puddleflange withweep holes 4 xplaces
100mm
A
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
*For flow rate data please refer to appendix.
F
G
Optional tailpiececonnector (suffix "E")
D
Structural slabN.B.
C
1.04
Optional couplingconnector (suffix "P")
Membrane
E
SPS Truflo 100mm & 150mm RWOwith Dome Grate & Membrane Clamp
B
Optional 100mmhigh 304 SSgravel guard forbuilt-up roofs -code - GG105(100mm high)or GG105H(150mm high)
Membrane ring fastens to bodyindependently of grate to allow accessto sump without breaking membraneseal.
Specification codes:TIA100D2 (CI body, aluminium dome grate & membrane ring)TIB100D2 (CI body, bronze dome grate & membrane ring)TBA100D2 (all-bronze assembly)- for 80mm outlet, use "100/80" instead of "100"- for 150mm outlet, use "150" instead of "100"
Suggested application:Roof decks
25
25
G
4537
28
28
103151
106
86
260
260
100150
240
240
N.B DA CB E F10680 260 82240 28 45 25
Specification code:TIA100PB (100mm CI body with planter box adapter)TIA150PB (150mm CI body with planter box adapter)
SPS Truflo 100mm & 150mm RWOwith All-purpose Planter Box Adapter
Integral puddleflange withweep holes 4 xplaces
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Membrane
Optional couplingconnector (suffix "P")
260 150
N.B
100
A
260 151 240
B
240
C 103
28 86
D106
E 28
2537
F45
G25
100Ø Socket
C
N.B.
A
B
D
Optional tailpiececonnector (suffix "E")
Structural slabG
F
E
1.05
Adapter made fromheavy-duty ABS plasticand features an integral100mm socket suitable forslotted PVC riser.
Inspection cap (by others)
100mm Slotted PVC (by others)
Drainage cell etc (by others)
Dimensions (mm)
SPS Truflo 80mm & 100mm 90° RWOwith Class D Heavy-Duty Flat Grate
Structural Slab
Integral puddleflange withweep holes 4 xplaces
D
Flat grate in heavy duty,hot-dipped galvanisedmid-carbon steel
S P S
Specification code:TIA80/90F (80mm CI body, galvanised steel flat grate)TIA100/90F (100mm CI body, galvanised steel flat grate)
A
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Outside edge of PVC pipe
E
*For flow rate data please refer to appendix.
N.B.
100
80 260
260
A
240
240
B
28
28
140
11562
83
C D E
B
1.06
C N.B.
Suggested applications:Car park decksPlant rooms
Load-tested to Class D of AS3996-2006
D
A
B
C N.B.
E
Integral puddleflange withweep holes 4 xplaces
Membrane ring fastens to bodyindependently of grate to allowaccess to sump without breakingmembrane seal.
Outside edge of PVC pipe
*For flow rate data please refer to appendix.
80
100
N.B.
260
260
A
240
240
B
62
83
C115
140
D
28
28
E
Structural Slab
1.07
Membrane
Suggested application:Membraned floors orroofs with no further topping,eg planter boxes, plantrooms, roof decks.
SPS Truflo 80mm & 100mm 90° RWOwith Flat Grate & Membrane Clamp
S P S
Specification codes:TIA80/90F2 (80mm CI body, aluminium clamp ring & grate)TIB80/90F2 (80mm CI body, bronze ring & grate)TIA100/90F2 (100mm CI body, aluminium clamp ring & grate)TIB100/90F2 (100mm CI body, bronze ring & grate)
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
D
Integral puddleflange withweep holes 4 xplaces
Optional 100mmhigh 304 SSgravel guard forbuilt-up roofs -code - GG105(100mm high)or GG105H(150mm high) A
Outside edge of 100mm PVC
E
EDCBAN.B.
100
80
260
260
240
240
83
62
140
115
28
28
Structural Slab
1.08
CN.B.
Membrane
Membrane ring fastens to bodyindependently of grate to allow accessto sump without breaking membraneseal.
Suggested applications:Roof decks with pipe cast in
SPS Truflo 80mm & 100mm 90° RWOwith Dome Grate & Membrane Ring
Specification codes:TIA80/90D2 (80mm CI body, aluminium clamp ring & dome)TIB80/90D2 (80mm CI body, bronze ring & dome)TIA100/90D2 (100mm CI body, aluminium clamp ring & dome)TIB100/90D2 (100mm CI body, bronze ring & dome)
B
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
*For flow rate data please refer to the appendix.
Specification code:TIA80/90PB (80mm CI body with planter box adapter)TIA100/90PB (100mm CI body with planter box adapter)
Integral puddleflange withweep holes 4 xplaces
D
SPS Truflo 80mm & 100mm 90° RWOwith All-purpose Planter Box Adapter
Adapter made from heavy-dutyABS plastic and features anintegral 100mm socket suitable forslotted PVC riser.
Outside edge of PVC pipe
E
2811562
83
C24026080
100 260 140240 28
A
B
N.B. A
Structural Slab
B D E
100Ø Socket
1.09
C N.B.
Membrane
Inspection cap (by others)
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Drainage cell etc (by others)
Slotted PVC riser (by others)
Flat grate in heavy duty,hot-dipped galvanisedmid-carbon steel
SPS 150mm Superflo RWO withClass D Heavy Duty Flat Grate
Specification codes:SIA150F (150mm Superflo CI body, galvanised flat grate)
Integral puddleflange withweep holes 4 xplaces
E
*For flow rate data please refer to appendix.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
G
F
Optional couplingconnector (suffix "P")
N.B.150 400
A B356 151
C150D E
66G38
F39
B
N.B.
C
A
Structural slab
D
Optional tailpiececonnector (suffix "E")
1.10
Suggested applications:Car park decks, especially roof top car parks
Load-tested to class D of AS3996-2006
Specification codes:SIA150F2 (150mm Superflo CI body, galvanised cast ironflat grate & aluminium membrane clamp ring)SIA150D2 (150mm Superflo - CI body, aluminium domegrate & membrane clamp ring)
SPS 150mm Superflo Flat or Dome RWO(with Membrane Clamp Ring)
Integral puddleflange withweep holes 4 xplaces
D
N.B.150
Speciality Plumbing Supplies Pty Ltd
AB
Membrane
E
G
Optional couplingconnector (suffix "P")
F
*For flow rate data please refer to appendix.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
C
400A
356B C
151F
39E66
D150 38
G
N.B.Optional tailpiece
connector (suffix "E")
Structural slab
1.11
Suggested applications:Large concrete roofs withheavy membraneSprinkler/hydrant test areas
DOME GRATEVERSION "D2"
FLAT GRATEVERSION "F2"
SPS "Shallowflo" 100mm Push-in RWO(Variation Based on Truflo System)
Body O.D. 260mm
N.B. 100mm
Grate O.D. 240mm
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Specification codes:SF100F (CI body, galvanised flat grate class D)SF100F2 (CI body, LM-6 flat grate & membrane ring)SF100D2 (CI body, LM-6 dome grate & membrane ring)
60mm
Structural slab
Hot-dipped galvanised mid-carbonsteel flat grate, loadclass D per AS 3996-2006FLOW RATE max 3 l/s
1.12
Suggested applications:Applications where regularTruflo is too deep to fit, butnot requiring normal"Truflo" flow rates
S P S
40mm
O.D. 97mm
I.D. 86mm
Min depth:32mm
USE WITH CAUTION: Flow rates are only a fraction of those of regular Truflo
O-rings to suit100mm PVC,HDPE & Copper
100mm
LM-6 flat grate andmembrane ring, forwaterproofed slabs (egroof decks & plant rooms).FLOW RATE MAX 3 l/s
LM-6 dome grate andmembrane ring, for roofslabs (note: optionalgravel guard partiallyillustrated)FLOW RATE MAX 3 l/s
Specification Codes:PD50CS (50mm CI body, 316 SS grate)PD80CA (80mm CI body, aluminium grate)PD80CS (80mm CI body, 316 SS grate)PD100CA (100mm CI body, aluminium grate)PD100CS (100mm CI body, 316 SS grate)
A
Front View Side View
Flashing/Membrane
Topping / Tiling
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
82
55
105
N.B.
8050
100 280
210
150A D
35
25
45
C
11765
153
B
45
35
25E
37
35
F20
Push-inoutlet nowstandard
Parapet Wall
Structural Slab
Flashing/Membrane
TypicalApplication
97
72
50G
1.13
Body made from hot-dipped galvanised cast iron
O-rings available for push-in connection to PVC, copperand 100mm HDPE
Grates available in aluminium and 316 stainless steel
Optional bronze and nickel-bronze grates available byspecial order only
D
SPS Parapet or Scupper Drains
B
C
F E
G
*For flow rate data please refer to appendix.
SECTION 2 Domestic, Push-in & Retro-fit Drains
2.01
2.02
2.03
2.04
2.05
2.06
2.07
2.08
2.09
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
2.18
2.19
2.20
2.21
2.22
2.23
2.24
2.25
2.26
2.27
Push-in & Retro Fit Drains
100mm Domestic Floor Waste (fine pattern)
100mm Round - Push-in
100mm Square - Push-in
130mm Round - Push-in
130mm Round (Grid Pattern) - Push-in
130mm Square - Push-in
130mm Square (Grid Pattern) - Push-in
130mm Square - 100mm (round insert version) - Push-in
150mm Round - Push-in
150mm Square - Push-in
150mm Square Hybrid - Push-in - Unifin
150mm Square (Grid Pattern) - Push-in
200mm Square - Push-in
200mm Square (Grid Pattern) - Push-in
200mm Square - Push-in (150 outlet)
225mm Round - Push-in
225mm Round - Push-in (150 outlet)
110mm Square Floor Waste w/- Lo-profile Puddle Flange
130mm Round Floor Waste w/- Lo-profile Puddle Flange
130mm Square Floor Waste w/- Lo-profile Puddle Flange
150mm Square (Hybrid) w/- Lo-Profile Puddle Flange
150mm Round - Retro-fit Lower Body
150mm Square - Retro-fit Lower Body
150mm Square (Grid Pattern) - Retro-fit Lower Body
200mm Square - Retro-fit Lower Body
200mm Square (Grid Pattern) Retro-fit Lower Body
225mm Round - 100mm Retro-fit Lower Body
To suite pipe (mm):
100
50 & 80
50 & 80
80, 90 & 100
100
80, 90 & 100
80 & 100
100
100
100
100
100
100
100
150
100
150
100
100
100
100
100
100
100
100
100
100
Specification codes:DG100SF (round frame)DG100SF2 (square frame)
SPS 100mm Domestic Floor Waste
110mm110mm
15mm
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
100mm N.B.
17mm
2.01
Made from cast 304-grade polishedstainless steel. Satin 316 gradenon-stock option.
Features traditional bayonet-type gratefitting and 5x5mm heel-friendly pattern.
Slip-in to 100mm PVC pipe or leak controlflange insert (by others) eg WonderCap
"DG100SF" "DG100SF2"
SPS
Side View
(New Heel-Friendly Pattern)
SPS
Specification codes:R100SR (50mm, satin 316SS)R100SR4 (50mm, polished 304SS)R100/80SR (80mm, satin 316SS)R100/80SR4 (80mm, polished 304SS)
SPS 100mm Round Push-in Floor Drain
With topping/tiling
Topping / Tiling
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
50mm80mm
N.B
2518
A
5046
B
C
N.B.
Structural slab
Min. Height"A" mm
Cast into slab
Structural slab
2.02
Round grate available in316 stainless steel. 304grade available by specialorder.
O-ring spigot pushes into50mm or 80mm PVC pipeonly.
50mm outlet80mm outlet
Typical Applications
100mmRound
SPS
D
B
6442
C D
5072
SPS 100mm Square Push-in Floor Drain
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] 2.03
100mmSquare
SPS
Square grate available in316 stainless steel. 304grade available by specialorder.
O-ring spigot pushes into50mm or 80mm PVC pipeonly.
Specification codes:Q100SR (50mm, satin 316SS)Q100SR4 (50mm, polished 304SS)Q100/80SR (80mm, satin 316SS)Q100/80SR4 (80mm, polished 304SS)
50mm outlet80mm outlet
D
Typical Applications
C
N.B.
N.B
50mm80mm
A
2518 50
46
B
With topping/tiling
Structural slab
Topping / Tiling
Min. Height"A" mm
B
C
6442
7250
D
Cast into slab
Structural slab
*For flow rate data please refer to appendix.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
SPS 130mm Round Push-in Floor Drain
Speciality Plumbing Supplies Pty Ltd
Specification codes:R130/80SR4 (80mm - polished 304SS)R130/80SR (80mm - satin 316SS)R130/85SR (90mm - satin 316SS)R130SR4 (100mm - polished 304SS)R130SR (100mm - satin 316SS)
Structural Slab
With topping/tiling
Min. height"A"
Tiling or topping
2.04
N.B.
Typical Applications
Structural Slab
Cast into slab
I.D. rubber rings tosuit various pipe
types (see below)
Round grate available in 304 or316 Stainless Steel.
O-ring spigot pushes into pipe.See below for specific size &material compatibility.
130mmRound
80mm outlet90mm outlet
100mm outlet
80mm90mm
N.B. A B C D
CB
20
100mm
D
Pipe compatibility
PVC and copper20 PVC stormwater only
PVC, HDPE and copper17 41
49
49
90.5
726475 85.5
97
*For flow rate data please refer to appendix.
Specification code:R130SRQ4 (polished 304 stainless steel)R130SRQ (satin 316 stainless steel)
SPS 130mm Round Push-in Floor Drain
Installation with puddle flange
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Structural Slab
I.D. rubber rings tosuit 100mm PVC,HDPE & copper
With topping/tiling Cast into slab
100 N.B.
Typical Applications
Standard PVC Pipe
Structural Slab
Tiling or topping
Min. height20mm
2.05
130mmRound
(Grid Pattern)100mm Outlet
SPECIAL ORDER ONLY
Grid Pattern (8mm sq. holes)
Cast into slab
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
SPS 130mm Square Push-in Floor Drain
Speciality Plumbing Supplies Pty Ltd
Specification codes:Q130/80SR4 (80mm - polished 304SS)Q130/80SR (80mm - satin 316SS)Q130/85SR (90mm - satin 316SS)Q130SR4 (100mm - polished 304SS)Q130SR (100mm - satin 316SS)
Structural Slab
With topping/tiling
Min. height"A"
Tiling or topping
2.06
N.B.
Typical Applications
Structural Slab
Cast into slab
I.D. rubber rings tosuit various pipe
types (see below)
Square grate available in304 or 316 stainless steel.
O-ring outlet pushes intopipe. See below for specificsize & material compatibility.
80mm outlet90mm outlet
100mm outlet
80mm90mm
N.B. A B C D
CB
20
100mm
D
Pipe compatibility
PVC and copper20 PVC stormwater only
PVC, HDPE and copper17 44
49
49
90.5
726475 85.5
97
130mmSquare
High-heel friendly pattern (6mm gaps)
*For flow rate data please refer to appendix.
SPS 130mm Square Push-in Floor Drain
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Specification code:Q130/80SRQ4 (80mm, polished 304SS) *special order*Q130/80SRQ (80mm, satin 316SS)Q130SRQ4 (100mm, polished 304SS) *special order*Q130SRQ (100mm, satin 316SS)
130mmSquare
2.07
80mm outlet100mm outlet(Grid Pattern)
Grid Pattern (8mm sq. holes)
PVC, HDPE and copper
PVC and copper
Pipe compatibility
I.D. rubber rings tosuit various pipe
types (see below)
100mm
N.B.
80mm1720
A
90.54449
B
64
C
9772
D
With topping/tiling
Structural Slab
Tiling or topping
"A"Min. height
B
D
N.B.
C
Typical Applications
Cast into slab
Structural Slab
Square grate available in304 or 316 stainless steel.
O-ring outlet pushes intopipe. See below for specificsize & material compatibility.
Tiling or topping
Standard PVC Pipe
Structural Slab
With topping/tiling Cast into slab
Specification code:Q130SR24 (polished 304SS)Q130SR26 (satin 316SS *special order*)
SPS 130mm Square Push-in Floor Drain
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Installation with puddle flange
20mmMin. height
100 N.B.
Typical Applications
I.D. rubber rings tosuit 100mm PVC,HDPE & copper
Structural Slab
2.08
100mm outlet(circular grate insert)
130mmSquare
Suggested match for square cleanout model Q130SCR(see section 7)
Optional hex-head security screws (use suffix "/SEC")
41mm 91mm
97mm
Specification codes:R150GR (linished bronze) *special order*R150NR (linished nickel bronze) *special order*R150SR (satin 316 stainless steel)R150SR4 (polished 304 stainless steel)
SPS 150mm Round Push-in Floor Drain
Installation with puddle flange
Standard PVC Pipe
Structural Slab
Min. height25mm
Tiling or topping
100 N.B.
Typical Application
I.D. rubber rings tosuit 100mm PVC,HDPE & copper
Structural Slab
2.09
100mm Outlet
High-heel friendly pattern (5mm gaps)
SPS150mmRound
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
55mm88mm
97mm
*For flow rate data please refer to appendix.
Standard PVC Pipe
With topping/tiling Cast into slab
Installation with puddle flange
Speciality Plumbing Supplies Pty Ltd
Specification codes:Q150GR (linished bronze) *special order*Q150NR (linished nickel bronze) *special order*Q150SR4 (polished 304 stainless steel)Q150SR (satin 316 stainless steel)
SPS 150mm Square Push-in Floor Drain
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Min. height28mm
Tiling or topping
2.10
100mm N.B.
Typical Applications
Structural Slab
I.D. rubber rings tosuit 100mm PVC,HDPE & copper
100mm Outlet
150mmSquare
65mm88mm
97mm
High-heel friendly pattern (6mm gaps)
*For flow rate data please refer to appendix.
SPS 150mm Square Hybrid Floor Waste
Structural Slab
100mm PVC Pipe
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm N.B.
HDPE pipes.Also suits copper, C.I.&
Typical Application
I.D. Unifin Seal
With 100mm "Unifin" Outlet (SS/PVC)Specification codes:QH150S4F (Polished 304SS grate)QH150S6F (Satin 316SS grate) *special order*
I.D. 81mm
150mm Square FloorWaste with "Unifin"connector to suit allknown 100mm pipes
Polished 304 stainlesssteel hinged grate withPVC underframe ("hybrid"style).
Satin 316 stainless steelavailable as specialorder.
PVC under-frame
Min. height 30mm Topping or Tiling
High-heel friendly pattern (6mm gaps)
150mmSquare
2.11
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Installation with puddle flange
SPS 150mm Square Push-in Floor DrainSpecification code:Q150SRQ (316 stainless steel)
Standard PVC Pipe
Tiling or topping
28mmMin. height
I.D. rubber rings tosuit 100mm PVC,HDPE & copper
100mm N.B.
Typical Applications
Structural Slab
2.12
100mm Outlet(Grid Pattern)
150mmSquare
Grid Pattern (8mm sq. holes)
65mm88mm
97mm
Specification code:Q200SR (satin 316 stainless steel)Q200SR4 (polished 304 stainless steel)
Installation with puddle flange
SPS 200mm Square Push-in Floor Drain
I.D. rubber ring sealsto suit 100mm PVC,
HDPE & copper
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
With topping/tiling Cast into slab
100 N.B.
30mm
Standard PVC Pipe
Tiling or topping
Min. height
Typical Applications
2.13
Structural Slab
100mm Outlet
SPS
High-heel friendly pattern (6mm gaps)
200mmSquare
68mm88mm
97mm
*For flow rate data please refer to appendix.
Load Class C per AS3996-2006
Installation with puddle flange
SPS 200mm Square Push-in Floor DrainSpecification code:Q200SRQ (satin 316 stainless steel)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
With topping/tiling
100mm N.B.
30mm
Standard PVC Pipe
Tiling or topping
Min. height
Typical Applications
2.14
Cast into slab
Structural Slab
I.D. rubber ring tosuit 100mm PVC,HDPE & copper
(Grid Pattern)100mm Outlet
200mmSquare
Grid Pattern (8mm sq. holes)
68mm88mm
97mm
Standard PVC Pipe
SPS 200/150mm Square Push-in Floor DrainSpecification code:Q200/150SR (satin 316 stainless steel)
Structural Slab
Min. Height30mm
Tiling or Topping
200mmSquare
Also suits copper, C.I.&HDPE pipes.
150 N.B.
Typical Applications
146mm
138mmRubber ring seal
2.15
SPS
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
*For flow rate data please refer to appendix.
With topping/tiling
Standard PVC Pipe
Specification code:R225SR (satin 316 stainless steel)
SPS 225mm Round Push-in Floor Drain
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Structural Slab
Tiling or topping
30mm
Installation with puddle flange
Min. height
2.16
100mm N.B.
Cast into slab
Typical Applications
I.D. rubber rings tosuit 100mm PVC,HDPE & copper
Structural Slab
SPS 225mmRound
High-heel friendly pattern (5.5mm gaps)
100mm Outlet
*For flow rate data please refer to appendix.
225mmRound
Tiling or topping
Min. height
Standard PVC Pipe
Structural Slab
SPS 225mm Round Push-in Floor DrainSpecification code:R225/150SR (satin 316 stainless steel)
Speciality Plumbing Supplies Pty Ltd
25mm
Rubber ring seal
Also suitscopper, C.I. &HDPE pipe
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
150mm NB
Typical Applications
O.D. 146mm
I.D. 138mm
2.17
150mm Outlet
SPS
High-heel friendly pattern (5.5mm gaps)
*For flow rate data please refer to appendix.
Specification codes:DG100SL2B/PF (Polished 316 Stainless Steel)Includes 100mm retro-fit puddle flange in ABS plastic
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
100mm Lo-profile Retro-fit Puddle FlangeSPS Special Square Floor Waste with
Height 18mm - 70mm
Screed/Tiling
Structural Slab
Standard PVC Pipe
Flange OD180mm
HDPE pipes.Also suits copper, C.I.&
1mm spacer fins (x4)
Typical Application
I.D Rubber ring seal
1mm spacer fins (x8)
Waterproof membrane
Retro-fit puddle flangewith ultra-thin face.
Domestic-style floorwaste assembly withPVC tail slips insideI.D. of flange. 1mmspacer fins allow forproper leak control.
Currently available inpolished 316 stainlesssteel only.
OD 87mmØ
ID 83mmØ
2.18
Specification codes:R130/87S/PF (satin 316 SS floor waste)R130/87SP/PF (satin 316 SS clean out) *special order*Includes 100mm retro-fit puddle flange in ABS plastic
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
100mm Lo-profile Retro-fit Puddle FlangeSPS 130mm Round Floor Waste with
Min. Height 25mm
Screed
Structural Slab
Standard PVC Pipe
Flange OD180mm
100mm N.B.
HDPE pipes.Also suits copper, C.I.&
1mm spacer fins (x4)
Typical Application
I.D Rubber ring seal
1mm spacer fins (x8)
Waterproof membrane
Retro-fit puddle flangewith ultra-thin face.
Floor waste assemblyslips inside I.D. offlange. 1mm spacerfins allow for properleak control.
Floor waste availablesatin 316 stainlesssteel.
Satin 316 SS cleanout(solid top) alsoavailable by specialorder.
2.19
Specification codes:Q130/87S/PF (Polished 304 Stainless Steel)Q130/87S6/PF (Satin 316 Stainless Steel)Includes 100mm retro-fit puddle flange in ABS plastic
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
100mm Lo-profile Retro-fit Puddle FlangeSPS 130mm Square Floor Waste with
Min. Height 25mm
Screed
Structural Slab
Standard PVC Pipe
Flange OD180mm
100mm N.B.
HDPE pipes.Also suits copper, C.I.&
1mm spacer fins (x4)
Typical Application
I.D Rubber ring seal
1mm spacer fins (x8)
Waterproof membrane
Retro-fit puddle flangewith ultra-thin face.
Floor waste assemblyslips inside I.D. offlange. 1mm spacerfins allow for properleak control.
Available in polished304 or satin 316stainless steel.
Cleanouts alsoavailable - polishedand non-slip.
2.20
Specification codes:QH150/87S4/PF (Polished 304 Stainless Steel)QH150/87S6/PF (Satin 316 Stainless Steel)Includes 100mm retro-fit puddle flange in ABS plastic*Note: underframe of grate assembly is PVC plastic
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
100mm Lo-profile Retro-fit Puddle FlangeSPS 150mm Square Floor Waste with
Screed
Structural Slab
Standard PVC Pipe
Flange OD180mm
100mm N.B.
HDPE pipes.Also suits copper, C.I.&
Typical Application
I.D Rubber ring seal
1mm spacer fins (x8)
Waterproof membrane
Retro-fit puddle flangewith ultra-thin profile.
Floor waste assemblyslips inside I.D. offlange. 1mm spacerfins allow for properleak control.
Available in polished304 or satin 316stainless steel.
Height 35 - 85mm
PVC under-frame
150mmSquare
High-heelfriendly pattern(6mm gaps)
2.21
With topping/tiling
Specification codes:R150G/Q (bronze grate, CI retro-fit body) *special order*R150N/Q (nickel bronze grate, CI retro-fit body) *special order*R150S4/Q (polished 304 stainless steel grate, CI retro-fit body)R150S/Q (satin 316 stainless steel grate, CI retro-fit body)
150mmRound
Q100Y2BCI retro-fitlower body
Membrane
SPS 150mm Round Retro-fit Floor Drain
Min: 22mmMax: 45mm**
**Optional Extension Piece
40
30
Height AdjustmentTypical Applications
Ø145mm
Cast into slab
Weep holesx 4 Places
2.22
Height-adjustablehigh-heel friendly grateassembly.
Available in bronze,nickel bronze, 304 and316 stainless steel.
Q100Y2B cast ironretro-fit body fits insidea Ø150mm core hole.*316 SS lower bodyavailable by specialorder*
High-heel friendly pattern (5mm gaps)
SPS
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm BSP
Ø190mm (flange diameter)
77mm
E100 PVC adapter(suffix "E")
Tiling/topping
100mm N.B.
100mm outlet
95mm
Optional couplingconnector (suffix "P")
With topping/tiling
Q100Y2BCI retro-fitlower body
Membrane
Min: 23mmMax: 46mm**
**Optional Extension Piece
40
30
Height AdjustmentTypical Applications
Ø145mm
Cast into slab
Weep holesx 4 Places
2.23Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm BSP
Ø190mm (flange diameter)
77mm
E100 PVC adapter(suffix "E")
Tiling/topping
SPS 150mm Square Retro-fit Floor DrainSpecification codes:Q150G/Q (bronze grate, CI retro-fit body) *special order*Q150N/Q (nickel bronze grate, CI retro-fit body) *special order*Q150S4/Q (polished 304 stainless steel grate, CI retro-fit body)Q150S/Q (satin 316 stainless steel grate, CI retro-fit body)
Height-adjustablehinged grate & frame.
Square top available inbronze, nickel bronze,304 and 316 stainlesssteel.
Q100Y2B cast ironretro-fit body fits inside aØ150mm core hole.*316 SS lower bodyavailable by specialorder*
100mm Outlet
150mmSquare
100mm N.B.
95mm
Optional couplingconnector (suffix "P")
High-heel friendly pattern (6mm gaps)
With topping/tiling
Q100Y2BCI retro-fitlower body
Membrane
Min: 23mmMax: 46mm**
**Optional Extension Piece
40
30
Height AdjustmentTypical Applications
Ø145mm
Cast into slab
Weep holesx 4 Places
2.24Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm BSP
Ø190mm (flange diameter)
77mm
E100 PVC adapter(suffix "E")
Tiling/topping
SPS 150mm Square Retro-fit Floor DrainSpecification codes:Q150SQ/Q (satin 316 stainless steel grate, CI retro-fit body) 100mm Outlet
(Grid Pattern)
Height-adjustablehinged grate & frame.
Square top available in316 stainless steel (304stainless steelnon-stock option).
Q100Y2B cast ironretro-fit body fits inside aØ150mm core hole.*316 SS lower bodyavailable by specialorder*
150mmSquare
Grid Pattern (8mm sq. holes)
100mm N.B.
95mm
Optional couplingconnector (suffix "P")
With topping/tiling
Q100Y2BCI retro-fitlower body
Membrane
Min: 25mmMax: 45mm**
**Optional Extension Piece
40
30
Height Adjustment
Typical Applications
Ø145mm
Cast into slab
Weep holesx 4 Places
2.25Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm BSP
Ø190mm (flange diameter)
Optional couplingconnector (suffix "P")
77mm
E100 PVC adapter(suffix "E")
Tiling/topping
SPS 200mm Square Retro-fit Floor DrainSpecification codesQ200G/Q (bronze grate, CI retro-fit body) *special order*Q200N/Q (nickel bronze grate, CI retro-fit body) *special order*Q200S4/C (polished 304 stainless steel grate, CI retro-fit body)Q200S/Q (satin 316 stainless steel grate, CI retro-fit body)
100mm Outlet
Height-adjustablehigh-heel friendly grateassembly.
Available in bronze,nickel bronze andstainless steel (SSmodel is hinged).
Q100Y2B cast ironretro-fit body fits insidea Ø150mm core hole.*316 SS lower bodyavailable by specialorder*
200mmSquare
SPS
6mm Gaps
100mm N.B.
95mm
With topping/tiling
Q100Y2BCI retro-fitlower body
Membrane
Min: 25mmMax: 45mm**
**Optional Extension Piece
40
30
Height Adjustment
Typical Applications
Ø145mm
Cast into slab
Weep holesx 4 Places
2.26Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm BSP
Ø190mm (flange diameter)
77mm
E100 PVC adapter(suffix "E")
Tiling/topping
Height-adjustablehinged grate assembly.
Available in 316stainless steel.
Q100Y2B cast ironretro-fit body fits insidea Ø150mm core hole.*316 SS lower bodyavailable by specialorder*
200mmSquare
Grid Pattern (8mm sq. holes)
Specification codes:Q200SQ/Q (316 stainless steel grate, CI retro-fit body)
SPS 200mm Square Retro-fit Floor Drain100mm Outlet(Grid Pattern)
100mm N.B.
Optional couplingconnector (suffix "P")
95mm
With topping/tiling
Q100Y2BCI retro-fitlower body
Membrane
Min: 30mmMax: 55mm**
**Optional Extension Piece
40
30
Height Adjustment
Typical Applications
Ø145mm
Cast into slab
Weep holesx 4 Places
2.27Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm BSP
Ø190mm (flange diameter)
77mm
E100 PVC adapter(suffix "E")
Tiling/topping
SPS 225mm Round Retro-fit Floor DrainSpecification codesR225N/Q (nickel bronze grate, CI retro-fit body) *special order*R225S/Q (316 stainless steel grate, CI retro-fit body)
100mm OutletHeight-adjustablehigh-heel friendly grateassembly.
Available nickel bronzeand 316 stainless steel.
Q100Y2B cast ironretro-fit body fits insidea Ø150mm core hole.*316 SS lower bodyavailable by specialorder*
100mm N.B.
SPS225mmRound
High-heel friendlypattern (5.5mm gaps)
Optional couplingconnector (suffix "P")
95mm
SECTION 3 Vari-level Drains – Vertical Outlets
3.01
3.02
3.03
3.04
3.05
3.06
3.07
3.08
3.09
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
3.18
3.19
3.20
3.21
100mm Round
100mm Square
130mm Round
130mm Square
130mm Square (Grid Pattern)
130mm Round
130mm Square
130mm Square (Grid Pattern)
150mm Round
150mm Square
150mm Square (Grid Pattern)
200mm Square
200mm Square (Grid Pattern)
225mm Round
100m Truflo – Vari-Level Floor Drains
200mm Square (150 outlet)
225mm Round (150 outlet)
225mm Square (150 outlet)
300mm Round (150 outlet)
300mm Square (150 outlet)
300mm Square - Special Fine Pattern (150 outlet)
To suit pipe size (mm):
50 / 65
50 / 65
50 / 65
50 / 65
50 / 65
100
100
100
100
100
100
100
100
100
100
150 (or 100)
150 (or 100)
150 (or 100)
150 (or 100)
150 (or 100)
150 (or 100)
Specification code:R100G/C65 (bronze grate, CI lower body) *special order*R100N/C65 (nickel bronze grate, CI lower body) *special order*R100S4/C65 (polished 304 stainless steel grate, CI lower body)R100S/C65 (satin 316 stainless steel grate, CI lower body)
SPS
Typical Application
65mm BSP
'B'
A9060
N.B
SPS 100mm Round Vari-Level Vertical Drain
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
'A'
65
N.B.50
C65A CIlower body
100mmRound
Height adjustment:Min. 20mmMax. 65mm
Outlet pushes into 65mmPVC or copper with o-ringconnection, or connects to50mm PVC / HDPE withno-hub coupling.180
180B
Weep slots3 x places
Membrane
3.01
Tiling/Paving/Topping
Round grate available inpolished 304 & satin 316Stainless Steel. Bronze andnickel-bronze available byspecial order order.
Cast iron lower body andreversible membrane clampcollar with female 65mm BSPthread.
65/50mm Outlet
Specification code:Q100G/C65 (bronze grate, CI lower body) *special order*Q100N/C65 (nickel bronze grate, CI lower body) *special order*Q100S4/C65 (polished 304 stainless steel grate, CI lower body)Q100S/C65 (satin 316 stainless steel grate, CI lower body)
SPS
Typical Application
'B'
65mm BSP
9060
N.B
SPS 100mm Square Vari-Level Vertical Drain
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
'A'
6550
N.B.
C65A CIlower body
Height adjustment:Min. 20mmMax. 65mm
Membrane
Outlet pushes into 65mmPVC or copper with o-ringconnection, or connects to50mm PVC / HDPE withno-hub coupling.180
A B180
Weep slots3 x places
3.02
Tiling/Paving/Topping
Square grate available inpolished 304 & satin 316stainless steel. Bronze &nickel-bronze available byspecial order only.
Cast iron lower body andreversible membrane clampcollar with female 65mm BSPthread.
65/50mm Outlet
Specification code:R130S/C65 (satin 316 stainless steel grate, CI lower body)R130S4/C65 (polished 304 stainless steel grate, CI lower body)
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
SPS 130mm Round Vari-Level Vertical Drain
'A'
Height adjustment:Min. 22mmMax. 68mm
Outlet pushes into 65mmPVC or copper with o-ringconnection, or connects to50mm PVC / HDPE withno-hub coupling.
N.B
1801806065
N.B.50 90
A B
'B'
65mm BSP
C50A CIlower body
Weep slots3 x places
Membrane
3.03
65/50mm Outlet
Round grate available inpolished 304 or satin316 stainless steel.
Cast iron lower body andreversible membrane clampcollar with female 65mm BSPthread.
Typical Application
130mmRound
Tiling/Paving/Topping
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Specification code:Q130S/C65 (satin 316 stainless steel grate, CI lower body)Q130S4/C65 (polished 304 stainless steel grate, CI lower body)
Height adjustment:Min. 22mmMax. 68mm
SPS 130mm Square Vari-Level Vertical Drain
'A'
Outlet pushes into 65mmPVC or copper with o-ringconnection, or connects to50mm PVC / HDPE withno-hub coupling.
N.B
65 6050
N.B.90A
180180B
'B'
65mm BSP
C65A CIlower body
Weep slots3 x places
Membrane
3.04
Square grate available inpolished 304 or satin316 stainless steel.
Cast iron lower body andreversible membrane clampcollar with female 65mm BSPthread.
65/50mm Outlet
130mmSquare
SPS
Typical Application
Tiling/Paving/Topping
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Specification code:Q130S/C65 (satin 316 stainless steel grate)Q130S4/C65 (polished 304 stainless steel grate)Includes 65/50mm cast iron lower body
'A'
SPS 130mm Square Vari-Level Vertical Drain
Height adjustment:Min. 25mmMax. 68mm
Outlet pushes into 65mmPVC or copper with o-ringconnection, or connects to50mm PVC / HDPE withno-hub coupling.
N.B
906065
50N.B. A
180
B180
65mm BSP
'B'
C65A CIlower body
Weep slots3 x places
Membrane
3.05
Square grate available inpolished 304 or satin316 stainless steel.
Cast iron lower body andreversible membrane clampcollar with female 65mm BSPthread.
65/50mm Outlet(Square Hole Pattern)
Typical Application
130mmSquare
Tiling/Paving/Topping
Membrane flange 235Ø
95mm
Specification codes:R130S4/C (polished 304 stainless steel grate)R130S/C (satin 316 stainless steel grate)Includes 100mm cast iron lower body
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
SPS 130mm Round Vari-Level Vertical Drain
Height adjustment:Min. 20mmMax. 55mm**
30
**Optional Extension Piece
40
65mm
Optionalcoupling
connection
Push-inconnection
(specify: -R)100mm N.B.
Typical Application
C100A CIlower body
Weep slots3 x places
Tiling/Paving/Topping
Membrane
3.06
Height-adjustable grateassembly.
Available in polished304 or satin 316stainless steel.
C100A CI "deluxe"lower body withreversible clamp collar.
130mmRound
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Specification codes:Q130S4/C (polished 304 stainless steel grate)Q130S/C (satin 316 stainless steel grate)Includes 100mm cast iron lower body
SPS 130mm Square Vari-Level Vertical Drain
3.07
100mm Outlet
Height-adjustable grateassembly.
Available in polished304 or satin 316stainless steel.
C100A CI "deluxe"lower body withreversible clamp collar.
130mmSquare
SPS
Membrane flange 235Ø
95mm
Height adjustment:Min. 20mmMax. 55mm**
30
**Optional Extension Piece
40
65mm
Optionalcoupling
connection
Push-inconnection
(specify: -R)100mm N.B.
Typical Application
C100A CIlower body
Weep slots3 x places
Tiling/Paving/Topping
Membrane
C100A CIlower body
95mm
Membrane flange 235Ø
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Specification codes:Q130SQ4/C (polished 304 stainless steel grate)Q130SQ/C (satin 316 stainless steel grate)Includes 100mm cast iron lower body
SPS 130mm Square Vari-Level Vertical Drain
30
**Optional Extension Piece
40
Height adjustment:Min. 20mmMax. 55mm**
65mm
100mm N.B.
Push-inconnection
(specify: -R)
Optionalcoupling
connection
Typical Application
Weep slots3 x places
Tiling/Paving/Topping
Membrane
3.08
(Grid Pattern)100mm Outlet
Height-adjustable grateassembly.
Available in polished304 or satin 316stainless steel.
C100A CI "deluxe"lower body withreversible clamp collar.
130mmSquare
Height adjustment:Min. 25mmMax. 60mm**
**Optional Extension Piece
SPS 150mm Round Vari-Level Vertical DrainSpecification codes:R150G/C (bronze grate, CI lower body) *special order*R150N/C (nickel bronze grate, CI lower body) *special order*R150S4/C (polished 304 stainless steel, CI lower body)R150S/C (satin 316 stainless steel grate, CI lower body)
Typical Application
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Weep slots3 x places
Membrane flange 235Ø
Push-inconnection
(specify: -R)
65mm
Tiling/Paving/Topping
100mm N.B.
Optionalcoupling
connection
30
40
95mm
C100A CIlower body
3.09
Membrane
100mm Outlet
High-heel friendly pattern (5mm gaps)
SPS150mmRound
Heigh-adjustable high-heelfriendly grate assembly.
Available in polished 304 &satin 316 stainless steel.Bronze and nickel-bronzeavailable by special orderonly.
C100A "deluxe" CI lowerbody with reversible clampcollar.
*For flow rate data please refer to appendix.
Height adjustment:Min. 25mmMax. 60mm**
95mm
**Optional Extension Piece
SPS 150mm Square Vari-Level Vertical DrainSpecification codes:Q150G/C (bronze grate, CI lower body - non-stock option)Q150N/C (nickel bronze grate, CI lower body)Q150S4/C (polished 304 stainless steel, CI lower body)Q150S/C (satin 316 stainless steel grate, CI lower body)
Typical Application
Membrane
Weep slots3 x places
Push-inconnection
(specify: -R)
Tiling/Paving/Topping
65mm
Membrane flange 235Ø
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Optionalcoupling
connection 100mm N.B.
30
40
C100A CIlower body
3.10
Height-adjustable hingedgrate assembly.
Available in polished 304 &satin 316 stainless steel.Bronze and nickel-bronzeavailable by special orderonly.
C100A CI "deluxe" lowerbody with reversible clampcollar.
100mm Outlet
*For flow rate data please refer to appendix.
150mmSquare
High-heel friendly pattern (6mm gaps)
SPS 150 Square Vari-Level Vertical DrainSpecification codes:Q150SQ/C (316 stainless steel grate, CI lower body)
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
150mmSquare
3.11
Height-adjustable hingedgrate assembly.
Available in satin 316stainless steel only.
C100A CI "deluxe" lowerbody with reversible clampcollar.
(Grid Pattern)100mm Outlet
95mm
Height adjustment:Min. 25mmMax. 60mm** Typical Application
Membrane flange 235Ø
65mm
Tiling/Paving/Topping
Push-inconnection
(specify: -R)
Weep slots3 x places
Membrane
30
100mm N.B.
Optionalcoupling
connection40
C100A CIlower body
**Optional Extension Piece
95mm
SPS 200mm Square Vari-Level Vertical DrainSpecification codes:Q200G/C (bronze grate, CI lower body) *special order*Q200N/C (nickel-bronze grate, CI lower body) *special order*Q200S4/C (polished 304 stainless steel, CI lower body)Q200S/C (satin 316 stainless steel grate, CI lower body)
Height adjustment:Min. 30mmMax. 70mm**
**Optional Extension Piece
Weep slots3 x places
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
65mm
Tiling/Paving/Topping
Membrane
Membrane flange 235Ø
Optionalcoupling
connection
Push-inconnection
(specify: -R)100mm N.B.
40
30
Typical Application
C100A CIlower body
3.12
Height-adjustable hingedgrate assembly.
Available in polished 304 &satin 316 stainless steel.Bronze and nickel -bronzeavailable by special orderonly.
C100A CI "deluxe" lowerbody with reversible clampcollar.
100mm Outlet
High-heel friendly pattern (6mm gaps)
200mmSquare SPS
*For flow rate data please refer to appendix.
Load Class C perAS3996-2006
200mmSquare
95mm
40
30
SPS 200mm Square Vari-Level Vertical DrainSpecification codes:Q200SQ/C (satin 316 stainless steel grate, CI lower body)
Height adjustment:Min. 30mmMax. 70mm**
**Optional Extension Piece
Typical Application
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
65mm
Tiling/Paving/Topping
100mm N.B.
Optionalcoupling
connection
Membrane flange 235Ø
Push-inconnection
(specify: -R)
C100A CIlower body
Weep holes3 x places
Membrane
3.13
Height-adjustablehinged grate assembly.
Available in satin 316stainless steel only.
C100A CI "deluxe"lower body withreversible clamp collar.
100mm Outlet(Grid Pattern)
Grid Pattern (8mm square holes )
95m
m
Specification codes:R225N/C (nickel bronze grate, CI lower body) *special order*R225S/C (satin 316 SS grate, CI lower body)
SPS 225mm Round Vari-Level Vertical Drain
Height adjustment:Min. 30mmMax. 70mm**
**Optional Extension Piece
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
65mm
Membrane flange Ø235
110 O.D.100mm N.B.
Optionalcoupling
connection40
30 Push-inconnection
(specify: -R)
Typical Application
C100ACI lowerbody
Weep slots3 x places
Membrane
3.14
Tiling/Paving/Topping
100mm OutletHeight-adjustablehigh-heel friendly grateassembly.
Available in satin 316stainless steel. Polished304SS and nickel-bronzeavailable by special orderonly.
C100A "deluxe" CI lowerbody with reversibleclamp collar.
SPS225mmRound
High-heel friendly pattern (5.5mm gaps)
*For flow rate data please refer to appendix.
Integral puddleflange withweep holes 4 xplaces
Further to page 1.01 - the 100mm Truflo RWO can be converted into a vari-level drain body with aCC100 reversible clamp collar. The following 100mm BSP grate assemblies can then be installed:
SPS 100mm Truflo Vari-Level Floor Drains
A
E
Optional couplingconnector (suffix "P")
G
F
Min / Max**
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Integral puddle flange Ø 270mm
N.B
100 260
A
240
B
103C
106D E
28 45F
CC100 reversible clamp collar
Vari-level grate assembly - see chart
N.B.
C
D
Optional PVC tailpiececonnector (suffix "E")
Structural slab
200 x 200shown
3.15
25G
20mm / 50mm
20mm / 50mm
20mm / 50mm
25mm / 60mm
25mm / 60mm
25mm / 60mm
30mm / 70mm
30mm / 70mm
30mm / 70mm
Min / Max**Height Adjustment
** = EP100 extension piece available to extend height
R130S
Q130S
Q130SQ
R150S
Q150S
Q150SQ
Q200S
Q200SQ
R225S
R130S4
Q130S4
Q130SQ4
R150S4
Q150S4
Q150SQ4
Q200S4
Q200SQ4
R225S4
n/a
n/a
n/a
R150N
Q150N
n/a
Q200N
n/a
R225N
n/a
n/a
n/a
R150G
Q150G
n/a
Q200G
n/a
n/a
130mm Round
130mm Square
130mm Square*
150mm Round
150mm Square
150mm Square*
200mm Square
200mm Square*
225mm Round
* = grid pattern
304SS316SS Ni-Br Bronze
**For additional height, useEP150 extension piece
150mm outlet shownwith PVC tailpiece
(in-pipe connector)
86mm
SPS 200mm Square Vari-Level Vertical Drain
Membrane
Height adjustment:Min. 25mmMax. 70mm**
Specification code:Q200S4/C150 (polished 304 stainless steel grate, CI lower body)Q200S/C150 (satin 316 stainless steel grate, CI lower body)For a 100mm outlet, use suffix "C100" not "C150"
Tiling/Paving/Topping
98mm
100mm outlet shownwith optional couplingconnector
Integral puddle flange Ø270
150 or 100mm N.B.
Typical Application
Structural Slab
3.16
150mm Outletor 100mm Outlet
Height-adjustable hingedgrate & frame.
Grate assembly available inpolished 304 and satin 316stainless steel.
150mm or 100mm Truflo CIlower body with 150mmBSP reversible clamp collar.
SPS200mmSquare
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Load Class C per AS3996-2006
*For flow rate data please refer to appendix.
**For additional height, useEP150 extension piece
Structural
Membrane
86mm
150mm outlet shownwith PVC tailpiece
(in-pipe connector)
225mmRound
SPS 225mm Round Vari-Level Vertical DrainSpecification code:R225N/C150 (nickel-bronze grate, CI lower body) *special order*R225S4/C150 (Polished 304SS grate, CI lower body) *special order*R225S/C150 (Satin 316SS grate, CI lower body)For a 100mm outlet, use suffix "C100" not "C150"
Height adjustment:Min. 30mmMax. 75mm
98mm
Tiling/Paving/Topping
Integral puddle flange Ø270
150 or 100 N.B.
Typical Application
Slab
100mm outlet shownwith optional couplingconnector
3.17
150mm Outletor 100mm Outlet
Height-adjustable highheel-friendly grateassembly.
Grate assembly available316 stainless steel.Polished 304SS andnickel-bronze availableonly by special order.
150mm or 100mm TrufloCI lower body with150mm BSP reversibleclamp collar.
High-heel friendly pattern (5.5mm gaps)
SPS
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Load Class C per AS3996-2006
*For flow rate data please refer to appendix.
**For additional height, useEP150 extension piece
Structural
86mm
150mm outlet shownwith PVC tailpiece
(in-pipe connector)
225mmSquare
SPS 225mm Square Vari-Level Vertical DrainSpecification code:Q225N/C150 (nickel-bronze grate, CI lower body) *special order*Q225S/C150 (316 stainless steel grate, CI lower body)For a 100mm outlet, use suffix "C100" not "C150"
Height adjustment:Min. 32mmMax. 80mm**
Membrane
98mm
Tiling/Paving/Topping
Integral puddle flange Ø270
150 or 100 N.B.
Typical Application
100mm outlet shownwith optional couplingconnector
Slab
3.18
150mm Outletor 100mm Outlet
Height-adjustable hingedgrate & frame.
Grate assembly available insatin 316 stainless steel.Nickel-bronze available byspecial order only.
150mm or 100mm Truflo CIlower body with 150mmBSP reversible clamp collar.
SPS
Load Class C per AS3996-2006
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
*For flow rate data please refer to appendix.
**For additional height, useEP150 extension piece
Structural
Membrane
86mm
SPS 300mm Round Vari-Level Vertical DrainSpecification code:R300D/C150 (galvanised ductile iron grate, CI lower body)R300S/C150 (satin 316 stainless steel grate, CI lower body)For a 100mm outlet, use suffix "C100" not "C150"
Height adjustment:Min. 50mmMax. 90mm**
300mmRound
98mm
Tiling/Paving/Topping
100mm outlet shownwith optional couplingconnector
Integral puddle flange Ø270
150 or 100 N.B.
Typical Application
Slab
3.19
150mm Outletor 100mm Outlet
Height-adjustableround grate & frame.
Grate assemblyavailable in galvanisedducktile iron,nickel-bronze, and 316stainless steel.
150mm or 100mmTruflo CI lower bodywith 150mm BSPreversible clampcollar.
SPS
Load Class C per AS3996-2006
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
150mm outlet shownwith PVC tailpiece
(in-pipe connector)
Structural
Specification codes:Q300D/150C (galvanised ductile iron grate, CI lower body)Q300S4/150C (polished 304 stainless steel grate, CI lower body)Q300S/150C (satin 316 stainless steel grate, CI lower body)For a 100mm outlet, use suffix "C100" not "C150"
86mm
150mm outlet shownwith PVC tailpiece
(in-pipe connector)
SPS 300mm Square Vari-Level Vertical Drain
**For additional height, useEP150 extension piece
Membrane
Height adjustment:Min. 50mmMax. 90mm**
300mmSquare
98mm
100mm outlet shownwith optional couplingconnector
Ø270
150 or 100 N.B.
Typical Application
Tiling/Paving/Topping
Slab
3.20
Height-adjustablehinged grate &frame.
Grate assemblyavailable in nickelbronze, ductile ironand 316 stainlesssteel.
150mm or 100mmTruflo CI lower bodywith 150mm BSPreversible clampcollar.
150mm Outletor 100mm Outlet
SPS
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Load Class C per AS3996-2006
**For additional height, useEP150 extension piece
Structural
86mm
150mm outlet shownwith PVC tailpiece
(in-pipe connector)
300mmSquare6mmGaps
SPS 300mm Square Fine Pattern Vertical DrainSpecification code:Q300S24/C150 (polished 304 SS grate, 150mm CI lower body)Q300S2/C150 (satin 316 SS grate, 150mm CI lower body)For a 100mm outlet, use suffix "C100" not "C150"
Height adjustment:Min. 50mmMax. 90mm**
Membrane
Tiling/Paving/Topping
98mm
100mm outlet shownwith optional couplingconnector
150 or 100 N.B.
Integral puddle flange Ø270
Stainless steel grate/frame
CI under-frame
Typical Application
Slab
3.21
(Vari-Level)
Special high-heelfriendly grate pattern.
Available in polished304 and satin 316stainless steel.
150mm or 100mmTruflo CI lower bodywith 150mm BSPreversible clamp collar.
SPS
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
SECTION 4 Vari-level Drains – 90° Outlets
4.01
4.02
4.03
4.04
4.05
4.06
4.07
4.08
4.09
4.10
4.11
4.12
4.13
4.14
4.15
Vari-Level Drains - Side Outlet
100mm Round
100mm Square
130mm Round
130mm Square
130mm Square (Grid Pattern)
150mm Round
150mm Square
150mm square (Grid Pattern)
200mm Square
200mm Square (Grid Pattern)
225mm Round
225mm Square
300mm Round
300mm Square
300mm Square (Fine Pattern)
To suit pipe size:
50 / 65
50 / 65
50 / 65
50 / 65
50 / 65
80 & 100
80 & 100
80 & 100
80 & 100
80 & 100
80 & 100
80 & 100
80 & 100
80 & 100
80 & 100
100mmRound
Specification code:R100G/C90 (bronze grate, ABS lower body) *special order*R100N/C90 (nickel-bronze grate, ABS lower body) *special order*R100S4/C90 (polished 304 stainless steel, ABS lower body)R100S/C90 (satin 316 stainless steel grate, ABS lower body)
'C''A'
SPS 100mm Round Vari-Level Side Outlet Drain
'D'
Outlet pushes into 65mm PVC or copper with o-ring connection,or connects to 50mm PVC/HDPE with no-hub coupling.
StructuralSlab
Membrane
Height adjustment:Min. 20mmMax. 65mm
Tiling/Paving/Topping
200200
A
105100
N.B.
6550
B
3740
C
180180
D
65mm BSP
N.B
Weep slots3 x places 'B'
4.01
65/50mm outlet
Typical Application
SPS
Round grate available inpolished 304 & satin 316stainless Steel. Bronze andnickel-bronze available byspecial order only.
ABS 90° Body and ReversibleMembrane Clamp Collar withfemale 65mm BSP thread.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
*For flow rate data please refer to appendix.
Outlet pushes into 65mm PVC or copper with o-ring connection,or connects to 50mm PVC/HDPE with no-hub coupling.
200200
100105
5065
N.B. A
3740B
180180
C D
4.02
Squre grate available in polished304 & satin 316 stainless Steel.Bronze and nickel-bronzeavailable by special order only.
ABS 90° Body and ReversibleMembrane Clamp Collar withfemale 65mm BSP thread.
SPS 100mm Square Vari-Level Side Outlet Drain
'C''D'
'A'
SPS
Membrane
StructuralSlab
Height adjustment:Min. 20mmMax. 65mm
65mm BSP
Typical Application
Specification code:Q100G/C90 (bronze grate, ABS lower body) *special order*Q100N/C90 (nickel bronze grate, ABS lower body) *special order*Q100S4/C90 (polished 304 stainless steel, ABS lower body)Q100S/C90 (satin 316 stainless steel grate, ABS lower body)
Weep slots3 x places
N.B
'B'
Tiling/Paving/Topping
65/50mm outlet
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
*For flow rate data please refer to appendix.
SPS 130mm Round Vari-Level Side Outlet DrainSpecification code:R130S4/C90 (polished 304 stainless steel, ABS lower body)R130S/C90 (satin 316 stainless steel grate, ABS lower body)
StructuralSlab
'C''A''D'
Outlet pushes into 65mm PVC or copper with o-ring connection, orconnects to 50mm PVC/HDPE with no-hub coupling.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Membrane
Height adjustment:Min. 25mmMax. 68mm
130mmRound
N.B.
6550
A
105100
CB4037
180180
D
200200
65mm BSP
N.B
Weep slots3 x places
Tiling/Paving/Topping
'B'
4.03
65/50mm outlet
Typical Application
Round grate assemblyavailable in polished 304 orsatin 316 stainless steel.
ABS 90° Body andReversible Membrane ClampCollar with female 65mmBSP thread.
*For flow rate data please refer to appendix.
SPS 130mm Square Vari-Level Side Outlet DrainSpecification code:Q130S4/C90 (polished 304 stainless steel, ABS lower body)Q130S/C90 (satin 316 stainless steel grate, ABS lower body)
Height adjustment:Min. 25mmMax. 68mm
'A'
'B'
N.B
Membrane
Outlet pushes into 65mm PVC or copper with o-ring connection, orconnects to 50mm PVC/HDPE with no-hub coupling.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
65 10550N.B.
100A
18037 200
C18040
B200D
65mm BSP'C'
'D'
StructuralSlab
Weep slots3 x places
4.04
65/50mm outlet
Tiling/Paving/Topping
Square grate assemblyavailable in polished 304 orsatin 316 stainless steel.
uPVC 90° Body andReversible Membrane ClampCollar with female 65mm BSPthread.
Typical Application
130mmSquare
*For flow rate data please refer to appendix.
SPS 130mm Square Vari-Level Side Outlet Drain
StructuralSlab
'D''C'
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Outlet pushes into 65mm PVC or copper with o-ring connection, orconnects to 50mm PVC/HDPE with no-hub coupling.
'A'
Height adjustment:Min. 25mmMax. 68mm
Specification code:Q130SQ4/C90 (polished 304 stainless steel, ABS lower body)Q130SQ/C90 (satin 316 stainless steel grate, ABS lower body)
130mmSquare
'B'
N.B
3710565
A100
N.B.50 40
B
200180
D200180
C
65mm BSP
Weep slots3 x places
Membrane
4.05
Square grate assemblyavailable in polished 304 orsatin 316 stainless steel.
ABS 90° Body and ReversibleMembrane Clamp Collar withfemale 65mm BSP thread.
65/50mm outlet(Grid Pattern)
Typical Application Tiling/Paving/Topping
Height adjustment:Min. 25mmMax. 60mm*
BA
Outside edge of PVC pipe
D
80
100
N.B.
260
260
A
240
240
B
62
83
C
* EP100 extension piece available to increase max. height
StructuralSlab
Membrane
CC100 clamp collar withweep holes 6 x places
Typical Application
4.06
115
140
D
28
28
E
C N.B.
E
Topping / Tiling / Paving
High-heel friendly pattern (5mm gaps)
SPS 150mm Round Vari-Level Floor DrainWith Side-Outlet Lower Body
Specification codes:R150G/C109 (bronze grate, CI lower body) *special order*R150N/C109 (nickel bronze grate, CI lower body) *special order*R150S4/C109 (polished 304 SS grate, CI lower body)R150S/C109 (satin 316 SS grate, CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
150mmRound
SPS
Height-adjustable grateassembly.
Available polished 304 and316 stainless steel. Bronzeand nickel-bronze availableby special order only.
CI "Truflo" side-outlet lowerbody with 100mm BSPreversible clamp collar.
100mm outlet80mm outlet
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Membrane
* EP100 extension piece available to increase max. height
Specification codes:Q150G/C109 (bronze grate, CI lower body) *special order*Q150N/C109 (nickel bronze grate, CI lower body) *special order*Q150S4/C109 (polished 304SS, CI lower body)Q150S/C109 (satin 316SS grate, CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
D
SPS 150mm Square Vari-Level Floor DrainWith Side-Outlet Lower Body
Height adjustment:Min. 25mmMax. 60mm*
Typical Application
E
Outside edge of PVC pipe
Topping / Tiling / Paving
CC100 clamp collar withweep holes 6 x places
StructuralSlab
BA
4.07
N.B.C
Height-adjustable hingedgrate assembly.
Available in polished 304 andsatin 316 stainless steel.Bronze and nickel-bronzeavailable by special orderonly.
CI "Truflo" side-outlet lowerbody with 100mm BSPreversible clamp collar.
100mm outlet80mm outlet
80
100
N.B.
260
260
A
240
240
B
62
83
C115
140
D
28
28
E
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
150mmSquare
High-heel friendly pattern (6mm gaps)
D
Height adjustment:Min. 25mmMax. 60mm*
SPS 150mm Square Vari-Level Floor DrainSide-Outlet Lower Body (Grid Pattern)
Specification codes:Q150SQ/C109 (satin 316SS grate, CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
AB
Outside edge of PVC pipe
Topping / Tiling / Paving
CC100 clamp collar withweep holes 6 x places
* EP100 extension piece available to increase max. height
StructuralSlab
Membrane
Typical Application
4.08
N.B.C
E
100mm outlet80mm outlet
Height-adjustable hinged grateassembly. Grate pattern 8mmsquare holes.
Available in satin 316 stainlesssteel only.
CI "Truflo" side-outlet lowerbody with 100mm BSPreversible clamp collar.
80
100
N.B.
260
260
A
240
240
B
62
83
C115
140
D
28
28
E
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
150mmSquare
Grid Pattern (8mm sq. holes)
Height adjustment:Min. 30mmMax. 70mm
SPS 200mm Square Vari-Level Floor DrainWith Side-Outlet Lower Body
D
Specification codes:Q200G/C109 (bronze grate, CI lower body) *special order*Q200N/C109 (nickel bronze grate, CI lower body) *special order*Q200S4/C109 (polished 304SS grate, CI lower body)Q200S/C109 (satin 316 SS grate, CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
* EP100 extension piece available to increase max. height
E
Topping / Tiling / Paving
Outside edge of PVC pipe
A
260
260
N.B.
80
100
B
240
240
62
83
C115
140
D
28
28
E
Typical Application
StructuralSlab
AB
CC100 clamp collar withweep holes 6 x places
Membrane
4.09
C N.B.
100mm outlet80mm outlet
Height-adjustable hingedgrate assembly.
Available in polished 304 andsatin 316 stainless steel.Bronze and nickel-bronzeavailable by special orderonly.
CI "Truflo" side-outlet lowerbody with 100mm BSPreversible clamp collar.
200mmSquare
SPS
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
High-heel friendly pattern (6mm gaps)
Specification code:Q200SQ/C109 (satin 316 SS grate, 100mm CI lower body)Q200SQ/C89 (satin 316 SS grate, 80mm CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
SPS 200mm Square Vari-Level Floor DrainSide-Outlet Lower Body, Grid Pattern
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] 4.10
100mm outlet80mm outlet
Height - adjustable grateassembly. Grate pattern8mm square holes.
Available in satin 316stainless steel only.
CI "Truflo" side-outletlower body with 100mmBSP reversible clampcollar.200mm
Square
Height adjustment:Min. 30mmMax. 70mm
Membrane
N.B.
100
StructuralSlab
AB
CC100 clamp collar withweep holes 6 x places
* EP100 extension piece available to increase max. height
D
80
D115
140
240
240260
260
A
83
C
62
B
28
28E
Outside edge of PVC pipe
Typical Application
N.B.C
Topping / Tiling / Paving
E
Grid Pattern (8mm sq. holes)
100
N.B.
80
140
115D
240
240
260
260
A
83
62
CB
28
28E
StructuralSlab
AB
CC100 clamp collar withweep holes 6 x places
* Not including EP100 extension piece
Specification codes:R225N/C109 (nickel bronze grate, CI lower body) *special order*R225S/C109 (satin 316 SS grate, CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
D
SPS 225mm Round Vari-Level Floor DrainWith Side-Outlet Lower Body
Height adjustment:Min. 30mmMax. 70mm*
Membrane
225mmRound
4.11
Outside edge of PVC pipe
Typical Application
N.B.C
Topping / Tiling / Paving
E
100mm outlet80mm outlet
Height-adjustable heel-friendlygrate assembly.
Available in satin 316 stainlesssteel. Nickel-bronze andpolished 304SS available byspecial order only.
CI "Truflo" side-outlet lowerbody with 100mm BSPreversible clamp collar.
SPS
High-heel friendly pattern (5.5mm gaps)
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
BA
100
N.B.
80
140
115D
240
240
260
260
A
83
62
CB
28
28E
**EP150 extension piece available to increase max. height
SPS
Specification codes:Q225N/C109 (nickel bronze grate, CI lower body) *special order*Q225S/C109 (satin 316 SS grate, CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
D
SPS 225mm Square Vari-Level Floor DrainWith Side-Outlet Lower Body
Height adjustment:Min. 32mmMax. 80mm**
StructuralSlab
Membrane
225mmSquare
4.12
Outside edge of 100mm PVC
CC150 clamp collar withweep holes 6 x places
CN.B.
Topping / Tiling / Paving
E
Height-adjustable hingedgrate assembly.
Available in satin 316stainless steel. Nickel-bronzeavailable by special orderonly.
CI "Truflo" side-outlet lowerbody with 150mm BSPreversible clamp collar.
Load tested to Class C ofAS3996-2006.
100mm outlet80mm outlet
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Typical Application
B
A
**EP150 extension piece available to increase max. height
Specification codes:R300D/C109 (galvanised ductile iron grate, CI lower body)R300S/C109 (satin 316 SS grate, CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
D
SPS 300mm Round Vari-Level Floor DrainWith Side-Outlet Lower Body
80
100
N.B.
StructuralSlab
Height adjustment:Min. 50mmMax. 90mm**
Membrane
300mmRound
4.13
Outside edge of 100mm PVC
240260
260 240
A B11562
83 140
C D
28
28
E
CC150 clamp collar withweep holes 6 x places
E
C N.B.
Topping / Tiling/ Paving
Height-adjustable grateassembly.
Available in galvanisedductile iron and 316stainless steel.
CI "Truflo" side-outlet lowerbody with 150mm BSPreversible clamp collar.
Load tested to Class C ofAS3996-2006.
SPS
100mm outlet80mm outlet
Typical Application
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Specification codes:Q300D/C109 (galvanised ductile iron grate, CI lower body)Q300S4/C109 (polished 304 SS grate, CI lower body)Q300S/C109 (satin 316 SS grate, CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
Height adjustment:Min. 30mmMax. 90**
CC150 clamp collar withweep holes 6 x places
B
A
StructuralSlab
Outside edge of 100mm PVC
D
100 260 240 83 140
**EP150 extension piece available to increase max. height
N.B.
80
Membrane
260
A
240
B C
62 115D
28
4.14
C N.B.
28E
Topping / Tiling/ Paving
E
SPS 300mm Square Vari-Level Floor DrainWith Side-Outlet Lower Body
300mmSquare SPS
Height-adjustable hingedgrate assembly.
Available in galvanisedductile iron and 316stainless steel.
CI "Truflo" side-outlet lowerbody with 150mm BSPreversible clamp collar.
Load tested to Class C ofAS3996-2006.
100mm outlet80mm outlet
Typical Application
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Membrane
Height adjustment:Min. 30mmMax. 90mm**
SPS 300mm Square Fine Pattern DrainWith Side-Outlet Lower Body
D
**EP150 extension piece available to increase max. height
300mmSquare6mmGaps
SPS
Specification code:Q300S24/C109 (polished 304 SS grate, 100mm CI lower body)Q300S2/C109 (satin 316 SS grate, 100mm CI lower body)Side outlet - "C109" = 100mm; "C89" = 80mm
CC150 clamp collar withweep holes 6 x places
B
A
StructuralSlab
Topping / Tiling/ Paving
E
Outside edge of 100mm PVC
Stainless steel grate/frame
CI under-frame
4.15
N.B.C
Height-adjustable grateassembly withhigh-heel-friendly pattern.
Available in polished 304and satin 316 stainlesssteel.
CI "Truflo" side-outletlower body with 150mmBSP reversible clampcollar.
100mm outlet80mm outlet
High-heel friendly pattern (6mm gaps)
Typical Application
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
260
260
N.B.
80
100
62
83
B
240
240
A C115
140
D
28
28
E
SECTION 5 Vinyl Floor Wastes
5.01
5.02
5.03
5.04
5.05
5.06
5.07
5.08
5.09
5.10
5.11
5.12
5.13
5.14
110mm Round - Push-in
117mm Round - Push-in
135mm Round - Push-in - Unifin
135mm Round - Push-in
135mm Round - Push-in - with 1.25” socket for portable baths
125mm Round - Low-profile - with retro-fit puddle flange
125mm Round - Low-profile - Unifin
125mm Round - Low-profile
220mm Round - Push-in (150 outlet)
125mm Round - Low-profile - Vari-level
155mm Round - Vari-level
220mm Round - Vari-level (150 outlet)
155mm Round - Vari-level - 90° Outlet
220mm Round - Vari-level - 90° Outlet
To suit pipe size (mm):
50
80
100
100
100
100
100
100
150
100
100
150
80 & 100
80 & 100
5.01
SPS 50mm Push-In Sheet Vinyl Floor Waste
with rim
I.D. rubber ring seal
50mm PVC Pipe
Structural slab
Base centred in core holeSteel trowel screed flush
Clamp Ring
Push-in floor waste assembly for sheetvinyl flooring.
Available in all 304 stainless steel. 316stainless steel top available by specialorder only.
O-ring adapts outlet to 50mm PVC.
DIMENSION IN MILLIMETRESOUTLET
112
Vinyl Floor
C
DIAMETER
50
ØA
100
ØB
DIMENSIONAL DATA
NOMINAL
Typical Application
35
ØC
Specification codes:LG50SSA4 (entire assembly in 304 stainless steel)LG50SSA6 (316 SS ring/grate, 304 SS body) *special order*
Speciality Plumbing Supplies Pty LtdTel:(02) 9417 1900 Fax:(02) 9417 0108 E-mail: [email protected]
ØD
42
Specification codes:V80SVA (304 stainless steel ring & grate, ABS body)V80SVA6 (316 stainless steel ring & grate, ABS body)V80SSA4 (All-304 stainless steel assembly)V80SSA6 (316 SS ring/grate, 304SS body) *special order*
SPS 80mm Push-in Sheet Vinyl Floor Waste
Ø130mm
5.02
28mm
53mmI.D. 64mm
O.D. 72mm
80mm Pipe
117mm
Typical ApplicationSheet Vinyl
Cement Screed
Structural Slab
SPS
Push-in floor wasteassembly for sheetvinyl flooring.
Vinyl floor drain bodyavailable in ABS and304. 316SS bodyavailable by specialorder.
Ring & grate availablein polished 304 and316 stainless steel.
O-rings adapt outlet to80mm PVC & copperpipe.
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
SPS 100mm Push-in Vinyl Floor Waste
Structural Slab
100mm PVC Pipe
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm N.B.
HDPE pipes.Also suits copper, C.I.&
I.D. Unversal Fin-Seal
& Cleanout with Universal Fin-SealSpecification codes:VH87CPA (ABS body, chrome-plated zinc-alloy top)VH87SVA (ABS body, polished 304SS top)*Cleanout (polished) VH87SPA (ABS body, 304SS* top)Cleanout (non-slip) VH87SPNA (ABS body, 304SS* top)* for 316, use "6" as suffix, eg "VH87SVA6"
I.D. 81mm
Sheet vinyl flooring
Vinyl floor waste slipsinside 100mm PVC,HDPE and copper withthe same UniversalFin-Seal connector.
Grates/rings available inchrome-plated zincalloy,polished 304SS and satin316SS.
Cleanout tops available inpolished or non-slip304SS. 316SS non-stockoption.
Cement Screed
Typical Application
33mm
5.03
135mm SPS
*5mm bar x 5mm gap heel friendly design*
Drain body OD 150mm
Structural Slab
Specification codes:V100SVA (ABS body, polished 304 SS ring & grate)V100SVA6 (ABS body, polished 316 SS ring & grate)V100SSA4 (Assembly in polished 304 stainless steel)V100SSA6 (Assembly in polished 316 stainless steel)
SPS 100mm Push-in Sheet Vinyl Floor Waste
135mm
Cement Screed
Sheet Vinyl
Ø150mm
I.D. 88mm
O.D. 97mm
50mm
25mm
Typical Application
100mm Pipe
5.04
Tamper-proof screws optional
Push-in floor waste assemblyfor sheet vinyl flooring.
Drain body available in ABS,zinc-alloy and 304 gradestainless steel. 316SSavailable by special order.
Ring & grate available inchrome-plated zinc-alloy orpolished 304 grade stainlesssteel. 316SS available byspecial order.
O-rings adapt outlet to100mm PVC, copper, HDPEor CI pipe.
Watermarked underATS5200:040 (ref: 20052)
SPS
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
*5mm bar x 5mm gap heel friendly design*
Structural Slab
Specification codes:V100SVA-HP(ABS body, polished 316 SS ring & grate)V100SSA6-HP (polished 316 SS ring & grate, drain body 304SS)
135mm
Cement Screed
Sheet Vinyl
Ø150mm
I.D. 88mm
O.D. 97mm
50mm
25mm
Typical Application
100mm Pipe
5.05
Tamper-proof screws optional
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
SPS 100mm Push-in Sheet Vinyl Floor Waste(with 1.25" socket for portable bath outlet)
Push-in floor wasteassembly for sheetvinyl flooring.
Grate includes a hosepipe socket suitablefor 1.25" i.d. hose, toenable directconnection into floorgrate.
Ring & grate availablein polished 316SSonly. Drain bodyavailable in ABSplastic or 304SS.
O-rings adapt spigotto 100mm PVC,copper, HDPE and CIpipe.
Grate (with 1.25" hose socket)Clamp Ring
Screed
Specification codes:Floor waste: LG87SVAP (ABS body, 304SS top)Cleanout (polished) LG87SVPAP (ABS body, 304SS top)Cleanout (non-slip) LG87SVPNAP (ABS body, 304SS top)Includes PF100 puddle flange
with slip-in Low Profile Vinyl Floor WasteSPS 100mm Retro-fit Puddle Flange
Min. Height 20mm
Structural Slab
Standard PVC Pipe
PuddleFlange OD
180mm
125mm
HDPE pipes.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Also suits copper, C.I.&
I.D Rubber ring seal
1mm spacer fins (x8)
Waterproof membrane
Sheet vinyl flooring
100mm N.B.
1mm spacer fins (x4)
Ø 81mm
5.06
Drain body OD142mm
Retro-fit puddle flangewith ultra-thin face.
Low profile vinyl floorwaste slips inside I.D.of flange. 1mm spacerfins allow for properleak control.
Polished 304-gradestainless steel ring andgrate.
Cleanouts alsoavailable - polishedand non-slip.
Watermarked underATS5200:040 lic. no.20052
SPS
Typical Application
Ø 97mm
Do not block spacerfins with liquidmembrane or leakcontrol will not work!
SPS 100mm Extra Compact Push-in
Structural Slab
100mm PVC Pipe
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm N.B.
HDPE pipes.Also suits copper, C.I.&
Typical Application
I.D. Uni-fin Seal
Vinyl Floor Waste/Cleanout with Uni-Fin
Min. Height 22mm
Specification codes:Floor waste: LG87SVAF (ABS body, 304SS top)Cleanout (polished) LG87SVPF (ABS body, 304SS top)Cleanout (non-slip) LG87SVPNF (ABS body, 304SS top)
Screed
I.D. 81mm
125mmSheet vinyl flooring
Lo-profile vinyl floorwaste slips inside 100mmPVC, HDPE and copperwith the new Uni-finadapter.
Polished 304-gradestainless steel ring andgrate, ABS plastic lowerbody
Cleanout tops alsoavailable - polished ornon-slip 304SS/
Drain body OD142mm
5.07
SPS 100mm Ultra Compact Push-in
Structural Slab
100mm PVC Pipe
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm N.B.
HDPE pipes.Also suits copper, C.I.&
Typical Application
ID Rubber Ring Seal
Vinyl Floor Waste/Cleanout
Min. Height 20mm
Specification codes:Floor waste: LG810SVA (ABS body, 304SS top)Cleanout (polished) LG810SPA (ABS body, 304SS top)Cleanout (non-slip) LG810SPNA (ABS body, 304SS top)
Screed
125mm
SPS
Sheet vinyl flooring
Lo-profile vinyl floorwaste slips inside 100mmPVC, HDPE and copperwith appropriate o-rings.
Polished 304-gradestainless steel ring andgrate, ABS plastic lowerbody
Cleanout tops alsoavailable - in polished ornon-slip 304SS.
Drain body OD142mm
Ø87
Ø97
Ultra-compact:Vinyl ClampOD 125mm
5.08
Min. height: 25mm
HDPE pipes.
Rubber ring seal
Also suits copper, C.I.&
Ø240mm
150mm NB
Typical Applicatioin
O.D. 146mm
I.D. 138mm
Standard PVC Pipe
Structural Slab
Vinyl floorClamp ring
5.09
Cementscreed
Push-in floor wasteassembly for sheet vinyl.
Drain body available in304 stainless as standardor 316 stainless steel asnon-stock option.
Ring & Grate available inpolished 304 and 316stainless steel.
SPS 220mm Sheet Vinyl Floor Waste(150mm Push-in)
Ø220 SPS
Specification codes:LG150SSA4 (All-304 stainless steel)LG150SSA6 (All-316 stainless steel)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Height adjustment:Min. 18mmMax. 50mm**
95mm
** Optionalextension
piece
Specification codes:LG810S4/C (304 SS vinyl floor waste, CI lower body)LG810S6/C (316 SS top, 304 SS drain body, CI lower body)* for retro-fit body use "/Q" instead of "/C"
Clamping ring
Weep slots3 x places
65mm
235Ø
Push-inconnection
(specify: -R)
100mm N.B.
Optionalcoupling
connection
30
40
Typical Application
Cement screed
5.10
Q100Y2B retro-fitlower body(optional)
Height-adjustable vinylfloor waste assembly.
Vinyl floor drain bodyavailable in 304 stainlesssteel; 316 stainless steelavailable by special order.
Ring & grate available inpolished 304 stainless steel;316 stainless steelavailable by special order.
C100A CI "deluxe" lowerbody with reversible clampingcollar ("/C").
Q100Y optional CI retro fitlower body fits inside150mmØ core hole ("/Q").
77mm
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Ø87
Ø125
Vinyl Sheet
Ultra-compact:Vinyl ClampOD 125mm
SPS 100mm Ultra Compact Vari-LevelSheet Vinyl Floor Drain - Ø125mm Inlet
Drain body OD142mm
SPS
Height adjustment:Min. 25mmMax. 50mm**
95mm
** Optionalextension
piece
Specification codes:LG100S4/C (304 SS vinyl floor waste, CI lower body)LG100S6/C (316 SS top, 304 SS drain body, CI lower body)* for retro-fit body use "/Q" instead of "/C"
SPS 100mm Vari-Level Sheet Vinyl Floor Drain
Clamping ring
Sheet Vinyl Floor
Weep slots3 x places
65mm
235Ø
Push-inconnection
(specify: -R)
100mm N.B.
Optionalcoupling
connection
30
40
Typical Application
Cement screed
5.11
Q100Y2B retro-fitlower body(optional)
Membrane
Ø155mm Inlet
Height-adjustable vinyl floor wasteassembly.
Vinyl floor drain body available in 304stainless steel; 316 stainless steel availableby special order.
Ring & grate available in polished 304stainless steel; 316 stainless steel availableby special order.
C100A CI "deluxe" lower body withreversible clamping collar ("/C").
Q100Y optional CI retro fit lower body fitsinside 150mmØ core hole ("/Q").
77mm
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
**For additional height, useEP150 extension piece
Height adjustment:Min. 30mmMax. 72mm**
86mm
SPS 150mm Vari-Level Sheet Vinyl Floor DrainSpecification codes:LG150S4/C150 (polished 304SS ring/grate, 304SS drain body)LG150S/C150 (satin 316SS grate, 304SS drain body)Includes 150mm Truflo CI cast-in lower bodyFor a 100mm outlet, use suffix "C100" not "C150"
98mm
100mm outlet shownwith optional couplingconnector
150 or 100 N.B.
Integral puddle flange Ø270
150mm outlet shownwith PVC tailpiece
(in-pipe connector)
Structural Slab
5.12
150mm Outletor 100mm Outlet
Height-adjustable vinylfloor waste assembly.
Drain body available in304 stainless steel.
Ring & Grate availablein polished 304stainless steel. Satin316 stainless steelavailable by specialorder.
150 or 100mm "Truflo"CI lower body with150mm clamp collar.
Ø220mm Inlet
Vinyl floor
Membrane
Ø220
Typical Application
Cement Screed
Clamp ring
SPS
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Specification codes:LG100S4/C109 (polished 304 SS floor waste, CI lower body)LG100S6/C109 (satin 316 SS floor waste, CI lower body)For 80mm outlet, use suffix "C89" not "C109"
Height adjustment:Min. 30mmMax. 50mm *
155mm Round Sheet Vinyl Floor DrainVari-Level Side-Outlet Lower Body
N.B.
100
D
* EP100 extension piece available to increase max. height
80
C N.B.
Outside edge of Pipe
5.13
100mm outlet80mm outlet
Ø175mm
Ø155mm
Height-adjustable, side outlet vinyl floorwaste assembly.
Drain body available in 304 stainlesssteel. 316 stainless steel available byspecial order.
Grate & ring available in polished 304.Satin 316 stainless steel available byspecial order.
CI Truflo 90° lower body with 100mmreversible clamp collar & i.d. rubber ringfor 100mm PVC, HDPE & copper pipe; or80mm PVC.
CC100 clamp collar withweep holes 6 x places
Typical Application
Structural Slab
Membrane
260
260
A
240
240
B62
83
C115
140
D
Vinyl Floor
28
28
E
E
Cement screed
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Height adjustment:Min. 30mmMax. 72mm**
220mm Round Sheet Vinyl Floor DrainVari-Level Side-Outlet Lower Body
D
** EP150 extension piece available to increase max. height
Specification codes:LG150S4/C109 (polished 304 SS grate, CI lower body)LG150S6/C109 (satin 316 SS grate, CI lower body) *special order*Side outlet - "C109" = 100mm; "C89" = 80mm
SPS
E
Outside edge of Pipe
A
260
260100
80
N.B.
83240
240
B C
62
28140
115D* E
28
CC150 clamp collar withweep holes 6 x places
StructuralSlab
Membrane
Clamp ring
5.14
C N.B.
Cement Screed
Vinyl floor
100mm outlet80mm outlet
220mmRound
Height-adjustable vinyl floorwaste assembly.
Drain body available in 304stainless steel. 316 stainlesssteel available by specialorder.
Grate & ring available inpolished 304 stainless steel.Satin 316 stainless steelavailable by special order.
CI Truflo 90° lower body with150mm reversible clampcollar & i.d. rubber ring for100mm PVC, HDPE &copper pipe; or 80mm PVC.
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
AB
SECTION 6 Basket Trap Floor Wastes
6.01
6.02
6.03
6.04
6.05
6.06
6.07
6.08
6.09
6.10
6.11
6.12
6.13
6.14
6.15
6.16
6.17
6.18
6.19
6.20
6.21
6.22
6.23
100mm Compact - Drop-in
130mm Round - Push-in
135mm Vinyl - Push-in
150mm Round - Push-in
150mm Square - Push-in
200mm Square - Push-in
200mm Square - Push-in 150
225mm Round - Push-in
225mm Round - Push-in 150
220mm Vinyl - Push-in 150
150mm Round - Vari-level - Shallow Body
150mm Square - Vari-level - Shallow Body
155mm Vinyl - Vari-level - Shallow Body
200mm Square - Vari-level - Shallow Body
225mm Round - Vari-level - Shallow Body
200mm Square - Vari-level - Deep Body
225mm Round - Vari-level - Deep Body
225mm Square - Vari-level - Deep Body
300mm Square - Vari-level - Deep Body
220mm Vinyl - Vari-level - Deep Body
350mm Square - Special Custom-made
Coles-Spec. Basket Trap Floor Trough
150mm Square - Push-in - “Smart Secondary Strainer”
To suit pipe size (mm):
100
100
100
100
100
100
150
100
150
150
100
100
100
100
100
100
100
100
100
100
100
100
100
SPS 100mm Compact Basket Trap Assembly
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Fixedsecondary
strainer4mm holes
Specification code:BA100S (304 stainless steel assembly)BA100SL (Shallow version, 100mm deep**)
Min. Depth 10mm
Tiling or Topping
180mm**
Ø97mm
6.01
Lift-out grate with mini-bayonetfitting.
Entire assembly in 304 stainlesssteel.
Includes removable basket andfixed secondary strainer.
Fits inside 100mm PVC, HDPE,CI and copper.
May be installed into a leakcontrol flange for waterproofedapplications.
(Drop-in)
Strainer BasketCode: SB753mm holes
Structuralslab
Ø112mm SPS
Typical Application
Cast in to slabTiled surface
100 N.B.
Typical Application
SPS 130mm Round Push-in Basket Trap
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Standard PVC Pipe
I.D. Rubber ring seal
Min. height
Tiling or topping
20mm
Specification code:R130SR-BT (304 stainless steel)R130SR6-BT (316SS grate assembly) *special order*Shallow version: use suffix -BTS *special order*
6.02
Round grate in cast 304stainless steel. Basket andstrainer in 304 stainlesssteel sheet.
Spigot fits inside 100mmPVC, copper, CI andHDPE.
Includes stainless steelremovable basket and fixedsecondary strainer.
Compatible with PVC leakcontrol flanges forwaterproofed applications.
C.I> & HDPE pipeAlso suits copper,
Structural slab
SPS
* shallow version: 85mm deep
41mm
91mm
Strainer BasketCode: SBV85
3mm holes
Fixed secondarystrainer - 4mm holes
130mmRound
160mm*
I.D. Rubber ring seal
Standard PVC Pipe
Min. height 25mm
Cement Screed
SPS 100mm Push-in Vinyl Floor Basket Trap
Structural Slab
Also suits copper, C.I.&HDPE pipes.
Sheet VinylØ150mm (floor drain body)
6.03
Push-in basket trapassembly for sheet vinylflooring.
Vinyl floor drain bodyavailable 304 stainlesssteel.
Ring & grate availablepolished 304 (316 stainlesssteel *special order*).
O-rings adapt outlet to100mm PVC, copper,HDPE and CI pipe.
SPS
Specification code:V100SSA-BT (304 stainless steel)V100SSA-BTS (304SS shallow version *special order*)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Strainer BasketCode: SBV85
3mm holes
Fixed secondarystrainer - 4mm holes
Ø135mm
135mm Round Inlet
50mm
170mm*
* shallow version: 90mm deep
Min. height30mm
Standard PVC Pipe
I.D. Rubber ring seal
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Speciality Plumbing Supplies Pty Ltd
SPS 150mm Round Push-in Basket TrapSpecification code:R150SR-BT (304 stainless steel grate)R150SR-BTS (304SS shallow version) *special order*
Tiling or topping
Also suits copper, C.I.&
185mm*
100 N.B.
HDPE pipes.
Structural Slab
6.04
Push-in grate assembly incast 304 stainless steel.316 stainless steelavailable by special order.
Spigot fits inside 100mmPVC, copper, CI andHDPE.
Includes stainless steelstrainer basket and fixedsecondary strainer.
Compatible with PVC leakcontrol flanges formembraned applications.
150mmRound
Strainer BasketCode: SBV85
3mm holes
Fixed secondarystrainer - 4mm holes
55mm
91mm* shallow version: 95mm deep
for 100mm pipe
Tiling or topping
Standard PVC Pipe
SPS 150mm Square Push-in Basket TrapSpecification code:Q150SR-BT (All-304 stainless steel)Q150SR6-BT (Grate assembly in 316SS)Shallow version: use suffix -BTS *special order*
I.D. Rubber ring seal
100 N.B.
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] 6.05
Push-in bucket trapassembly in 304 stainlesssteel. 316 stainless steelgrate assembly isnon-stock option.
Outlet fits inside 100mmPVC, copper, CI andHDPE.
Includes stainless steelremovable basket and fixedsecondary strainer.
Compatible with PVC leakcontrol flanges formembraned applications.
Structural Slab
Also suits copper, C.I.&HDPE pipes.
185mm*
150mmSquare
Min. height30mm
SPS
Strainer BasketCode: SBV85
3mm holes
Fixed secondarystrainer - 4mm holes
* shallow version: 105mm deep
65mm
91mm
for 100mm pipe
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
I.D Rubber ring seal
Standard PVC Pipe
SPS 200mm Square Push-in Basket TrapSpecification code:Q200SR1-BT (304 stainless steel)Q200SR6-BT (grate assembly in heel-friendly 316SS)Shallow version: use suffix -BTS *special order*
30mm
Tiling or topping
Min. height
185mm*
100 N.B.
HDPE pipes.Also suits copper, C.I.&
Structural Slab
6.06
Push-in grateassembly in 304stainless steel. 316stainless steel grateassembly available byspecial order.
Outlet fits inside100mm PVC, copper,CI and HDPE.
Includes stainlesssteel removablebasket and fixedsecondary strainer.
Compatible with PVCleak control flangesfor membranedapplications.
SPS
* shallow version: 105mm deep
Strainer BasketCode: SBV85
3mm holes
Fixed secondarystrainer - 4mm holes
65mm
91mm
200mmSquare
Typical Application
Support BarsLoad Class CAS3996-2006
for 100mm pipe
Load Class C perAS3996-2006
Standard PVC Pipe
Structural Slab
SPS 200mm Square Push-in Basket TrapSpecification code:Q200/150SR-BT (316 stainless steel)
Min. Height30mm
Tiling or Topping
200mmSquare
110mm
Also suits copper, C.I.&HDPE pipes.
150 N.B.
Fixed secondary strainer - 4mm holes
Typical Application
O.D. 146mm
Strainer BasketCode: SB150S
3mm holes Rubber ring seal
6.07
Push-in bucket trapassembly - 316stainless steel grateassembly.
Includes stainlesssteel removablebasket and fixedsecondary strainer.
Outlet fits inside150mm PVC, copper,CI and HDPE.
Grate assemblyload-tested to Class Cof AS3996-2006.
for 150mm pipe
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
SPS
185mm*
SPS 225mm Round Push-in Bucket Trap
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
I.D. Rubber ring seal
100mm PVC Pipe
Min. height
Tiling or Topping
30mm
100 N.B.
6.08
Also suits copper, C.I.&HDPE pipes.
Structural Slab
Round grate in cast 316stainless steel. Basketand strainer in 304stainless steel sheet.
Outlet fits inside 100mmPVC, copper, CI andHDPE.
Includes stainless steelremovable basket andfixed secondary strainer.
Compatible with PVCleak control flanges formembranedapplications.
65mm
91mm
Fixed secondarystrainer - 4mm holes
Strainer BasketCode: SBV85
3mm holes
225mmRound
SPS
for 100mm pipe
* shallow version: 105mm deep
Specification code:R225SR-BT (grate assembly in heel-friendly 316SS)Shallow version: use suffix -BTS *special order*
Standard PVC Pipe
Structural Slab
SPS 225mm Round Push-in Basket TrapSpecification code:R225/150SR-BT (316SS grate assembly)
Min. Height30mm
Tiling or Topping
118mm
Also suits copper, C.I.&HDPE pipes.
150 N.B.
Typical Application
O.D. 146mm
Rubber ring seal
6.09
for 150mm pipe
225mmRound
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Strainer BasketCode: SB150S
3mm holes
Fixed secondary strainer - 4mm holes
Push-in bucket trapassembly - 316stainless steelheel-friendly grateassembly.
Includes stainless steelremovable basket andfixed secondarystrainer.
Outlet fits inside150mm PVC, copper,CI and HDPE.
Grate assemblyload-tested to Class Cof AS3996-2006.
SPS
Min. height: 25mm
HDPE pipes.
Rubber ring seal
Also suits copper, C.I.&
Ø240mm (floor drain body)
150mm NB
Typical Applicatioin
O.D. 146mmStandard PVC Pipe
Structural Slab
Vinyl floorClamp ring
Cementscreed
Push-in basket trapassembly for sheet vinyl.
Includes stainless steelremovable basket and fixedsecondary strainer.
Drain body available in 304stainless. 316 stainlesssteel available by specialorder.
Ring & Grate available inpolished 304 stainless steel.Satin 316 stainless steelavailable by special order.
SPS 220mm Sheet Vinyl Floor Basket Trappush into 150mm pipe
SPS
Specification codes:LG150SSA-BT (All-304 stainless steel)
Fixed secondary strainer - 4mm holes
220mmRound
Strainer BasketCode: SB150S
3mm holes
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
118mm
6.10
** Use EP100extension piecefor additionalheight
Specification codes:R150SA (304 SS grate, CI retro-fit lower body)R150SSA (304 SS grate, 316 SS retro-fit lower body)R150SA2 (304 SS grate, C100A CI "deluxe" lower body)For 316SS grate add "6" eg "R150SA26"
SPS 150mm Round Vari-Level Basket Trap
95mm
Membrane
Optionalcouplingconnection
Ø235mm
100 N.B.110 O.D.
Fixed Secondary Strainer4mm holesOptional E100
PVC tailpiece
C100A CIlower body
Strainer BasketCode: SB903mm holes
Weep slots3 x places
6.11
(Shallow Body)
Tiling/Paving/Topping
Height adjustment:Min. 25mmMax. 60mm**
150mmRound
Typical Application
SPS
Height-adjustable bucket trapassembly with lift-out grate.
Grate assembly available in304 stainless steel. 316stainless non-stock option.
C100A CI "deluxe" lower bodywith reversible clamp collar(pictured).
Optional Q100Y2B CI retro-fitlower body fits inside 150mmØcore hole.
Q100Y2B retro-fitlower body(optional)
77mm
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100 N.B.110 O.D.Ø235mm
C100A CIlower body
Optional E100PVC tailpiece
95mm
** Use EP100extension piecefor additionalheight
Fixed Secondary Strainer4mm holes
6.12
Optionalcouplingconnection
Weep slots3 x places
Membrane
SPS 150mm Square Vari-Level Basket Trap
Height adjustment:Min. 25mmMax. 60mm**
150mmSquare
Typical Application
Specification codes:Q150SA (304 SS grate, CI retro-fit lower body)Q150SSA (304 SS grate, 316 SS retro-fit lower body)Q150SA2 (304 SS grate, C100A "deluxe" CI lower body)For 316SS grate, add "6" eg "Q150SA26"
Height-adjustable, hingedbasket trap assembly to suit100mm pipe.
Grate assembly available in 304or 316 stainless steel.
Includes stainless steelremovable basket and fixedsecondary strainer.
C100A CI "deluxe" lower bodywith reversible clamp collar(pictured).
Optional Q100Y2B CI retro-fitlower body fits inside 150mmØcore hole.
Tiling/Paving/Topping
(Shallow Body)
Q100Y2B retro-fitlower body(optional)
77mm
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Strainer BasketCode: SB853mm holes
SPS
Height adjustment:Min. 25mmMax. 50mm**
Ø235mm
Optional E100PVC tailpiece
** Use EP100extension piecefor additionalheight
Fixed Secondary Strainer4mm holes
100 N.B.110 O.D.
95mm
C100A CIlower body
Cement screed
Strainer BasketCode: SB853mm holes
6.13
Optionalcouplingconnection
Weep slots3 x places
Membrane
Sheet Vinyl Floor
Clamp ring
155mm
175mm
(Shallow Body)SPS 155mm Round Vinyl Floor Bucket Trap
Height-adjustable basket trap for sheetvinyl floor to suit 100mm pipe.
Drain body available in 304 stainless asstandard or 316 stainless steel as anon-stock option.
Ring & Grate available in polished 304or 316 stainless steel.
Includes stainless steel removablebasket and fixed secondary strainer.
C100A CI "deluxe" lower body withreversible clamping collar.
Optional CI or SS retro fit lower bodyfits inside 150mmØ core hole.
Specification codes:LG100A-S (304 SS ring & grate & body, CI retro-fit body)LG100A-SS (304 SS ring grate & body, 316 SS retro-fit body)LG100SA2 (304 SS ring, grate & body, CI "deluxe" body)
Typical Application
Q100Y2B retro-fitlower body(optional)
77mm
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Height adjustment:Min. 30mm
Max. 70mm**
Ø235mm
** Use EP100extension piecefor additionalheight
100 N.B.110 O.D.
Fixed Secondary Strainer4mm holesOptional
E100 PVCtailpiece
95mmC100A CIlower body
Tiling/Paving/ Topping
Strainer BasketCode: SB853mm holes
Typical Application
6.14
Optionalcouplingconnection
Weep slots3 x places
Membrane
SPS 200mm Square Vari-Level Basket Trap
200mmSquare SPS
Specification codes:Q200SA (304 SS grate, CI retro-fit lower body)Q200SSA (304 SS grate, 316 SS retro-fit lower body)Q200SA2 (304 SS grate, C100A CI "deluxe" lower body)For 316SS grate, add "6" eg "Q200SA26"
Height-adjustable, hingedbasket trap assembly to suit100mm pipe.
Grate assembly available in304 stainless steel; optional316 stainless steel.
Includes stainless steelremovable basket and fixedsecondary strainer.
C100A CI "deluxe" lowerbody with reversible clampcollar (pictured).
Optional CI or SS retro-fitlower body fits inside150mmØ core hole.
(Shallow Body)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Q100Y2B retro-fitlower body(optional)
77mm
Load Class C perAS3996-2006
Height adjustment:Min. 30mm
Max. 70mm** Typical Application
Ø235mm
** Use EP100extension piecefor additionalheight 100 N.B.
110 O.D.
OptionalE100 PVCtailpiece
95mmC100A CIlower body
Tiling or Topping
Strainer BasketCode: SB853mm holes
Fixed Secondary Strainer4mm holes
Optionalcouplingconnection
6.15
Weep slots3 x places
Membrane
SPS 225mm Round Vari-Level Basket Trap
225mmRound
SPS
Specification codes:R225SA (316 SS grate, CI retro-fit lower body)R225SSA (316 SS grate, 316 SS retro-fit lower body)R225SA2 (316 SS grate, C100A CI "deluxe" lower body) Height-adjustable bucket
trap assembly withhigh-heel friendly grate.
Grate assembly available in316 stainless steel.
Includes stainless steelremovable basket and fixedsecondary strainer.
C100A CI "deluxe" lowerbody with reversible clampcollar (pictured).
Optional CI or SS retro-fitlower body fits inside150mmØ core hole.
(Shallow Body)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Q100Y2B retro-fitlower body(optional)
77mm
Specification code:Q200SA3 (304 SS grate CI deep body)Q200SSA3 (316 SS grate, 316 SS deep body)Q200SA3-S (304 SS grate, CI shallow body)Q200SSA3-S (316SS grate, 316SS shallow body)
SPS 200mm Square Basket Trap Assembly
Height adjustment:Min. 25mmMax. 50mm**
** Use EP150 foradditional height
UNI-FIN connectorsuits 100mm PVCHDPE & Copper
Ø175mm
202mm
SecondaryStrainer
4mm holes
Membrane
Weep holes4 x places
Strainer BasketCode: SB1503mm holes
6.16
StructuralSlab
(Deep Body)
Tiling or Topping
200mmSquare
Typical Application
Height-adjustable hingedbasket trap assembly.
Grate assembly available incast 304 or 316 stainlesssteel. Load tested to Class Cof AS3996-2006.
Q150/100Y deep basket bodyfits inside 175mmØ core holeand is available in CI(standard) or 316 stainlesssteel.
Q150/100YL shallow bodysaves 100mm in depth - usedfor thinner slabs or invert levelproblems. *suffix -S*
Secondary strainer affixedwith M5 security screws.
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm N.B.
I.D. 79mm
Q150/100YLShallow body(102mm deep)
SPS
Ø175mm
202mm
Membrane
Weep holes4 x places
6.17
StructuralSlab
SPS 225mm Round Bucket Trap Assembly
Height adjustment:Min. 25mmMax. 55mm**
Tiling or Topping
225mmRound
(Deep Body)
** Use EP150 foradditional height
I.D. 79mm
UNI-FIN connectorsuits 100mm PVCHDPE & Copper
100mm N.B.
Q150/100YLShallow body(102mm deep)
Typical Application
Specification code:R225SA3 (304 SS grate CI deep body)R225SSA3 (316 SS grate, 316 SS deep body)R225SA3-S (304 SS grate, CI shallow body)R225SSA3-S (316SS grate, 316SS shallow body) Height-adjustable basket trap
assembly - heel-friendly finepattern.
Grate assembly available incast 316 stainless steel. Loadtested to Class C ofAS3996-2006.
Q150/100Y deep basket bodyfits inside 175mmØ core holeand is available in CI(standard) or 316 stainlesssteel.
Q150/100YL shallow bodysaves 100mm in depth - usedfor thinner slabs or invert levelproblems. *suffix -S*
Secondary strainer affixedwith M5 security screws.
SPS
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Strainer BasketCode: SB1503mm holes
SecondaryStrainer
4mm holes
Membrane
202mm
Tiling or Topping
SPS 225mm Square Basket Trap Assembly
** Use EP150 foradditional height
Height adjustment:Min. 28mmMax. 58mm**
Ø175mm
6.18
(Deep Body)
Weep holes4 x places
StructuralSlab
225mmSquare
I.D. 79mm
UNI-FIN connectorsuits 100mm PVCHDPE & Copper
100mm N.B.
Q150/100YLShallow body(102mm deep)
Height-adjustable hingedbucket trap assembly.
Grate assembly available incast 316 stainless steel. Loadtested to Class C ofAS3996-2006.
Q150/100Y deep basket bodyfits inside 175mmØ core holeand is available in CI(standard) or 316 stainlesssteel.
Q150/100YL shallow bodysaves 100mm in depth - usedfor thinner slabs or invert levelproblems. *suffix -S*
Secondary strainer affixedwith M5 security screws.
Specification code:Q225SA (316 SS grate CI deep body)Q200SSA3 (316 SS grate, 316 SS deep body)Q200SA3-S (3164 SS grate, CI shallow body)Q200SSA3-S (316SS grate, 316SS shallow body)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Strainer BasketCode: SB1503mm holes
SecondaryStrainer
4mm holes
SPS
Height adjustment:Min. 50mmMax. 75mm**
** Use EP150 foradditional height
Specification code:Q300DA (galvanised ductile iron grate, CI lower body)Q300SA (304 SS grate, CI lower bodyQ300SSA (316 SS grate, 316 SS lower body)For shallow version add suffix "-S" to above codes
202mm
SPS 300mm Square Basket Trap Assembly
175Ø
Weep holes4 x places
Tiling / Topping
Membrane
StructuralSlab
6.19
(Deep Body)
300mmSquare SPS
Height-adjustable hingedbasket trap assembly.
Grate assembly availablein cast 316 stainless steel.Load tested to Class C ofAS3996-2006.
Q150/100Y deep basketbody fits inside 175mmØcore hole and is availablein CI (standard) or 316stainless steel.
Q150/100YL shallow bodysaves 100mm in depth -used for thinner slabs orinvert level problems.*suffix -S*
Secondary strainer affixedwith M5 security screws.
I.D. 79mm
100mm N.B. UNI-FIN connectorsuits 100mm PVCHDPE & Copper
Q150/100YLShallow body(102mm deep)
Typical Application
Strainer BasketCode: SB1503mm holes
SecondaryStrainer
4mm holes
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Cement screed
Ø220mm
Membrane
Vinyl floor
Height adjustment:Min. 25mmMax. 52mm**
Weep holes4 x places
202mm
SPS 220mm Sheet Vinyl Floor Basket Trap
** Use EP150 foradditional height
Ø175mm
6.20
(Deep Body)
SPS
StructuralSlab
Clamp ring
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
I.D. 79mm
100mm N.B.
Q150/100YLShallow body(102mm deep)
UNI-FIN connectorsuits 100mm PVCHDPE & Copper
Height-adjustable basket trapassembly for sheet vinylflooring.
Grate assembly available incast 304 and 316 stainlesssteel.
Q150/100Y deep basket bodyfits inside 175mmØ core holeand is available in CI(standard) or 316 stainlesssteel.
Q150/100YL shallow bodysaves 100mm in depth - usedfor thinner slabs or invert levelproblems. *suffix -S*
Secondary strainer affixedwith M5 security screws.
Specification code:LG150A/S (304 SS grate assembly, CI deep body)LG150A/SSA (316 SS grate assembly, 316 SS deep body)LG150A/S-S (304 SS grate assembly, CI shallow body)LG150A/SSA-S (316SS grate assembly, 316SS shallow body)
Typical Application
Strainer BasketCode: SB1503mm holes
SecondaryStrainer
4mm holes
Specification code:Q300BTA (300mm square full 304SS)Q350BTA (350mm square full 304SS)Q450BTA (450mm square full 304SS)
SPS Square Special Basket Trap
6.21
(Custom made)
350mmSquare
All-304 stainless steelbasket trap assembly.
Load rated to Class Cof AS3996.
Lift-out grate madefrom heavy-duty10x10mm square bar,with 10mm gaps.
5mm x 5mm wedgewire (high heelfriendly) gratingavailable as option.
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Strainer basket
FixedSecondary
Strainer
100mmPVC orHDPE
Concreteties x 4
Structuralslab
Typical application
105mm
50mm
SPS Coles-Style Basket Trap Floor Trough
HEELGUARD slip resistant grating
Class 'C' loading
Removable basket and fixed secondarystrainer
Full 304-grade s/s construction[316-grade also available at extra cost]
Cross-break or built-in fall to outlet
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
75mm*
Outlet 89mm Ø x 100mm long.Fitted with removable strainer basketand fixed secondary strainer.
As required
As required
PLAN
FRONTELEVATION
75mm*
Pressedsafetyedge
133mm Overall
100mm C/O
5 5
20mm
SECTION
With Class "C" slip-resistant wedge wire gratingSpecification codes:BTT125C1 - standard wedge-wire gratingBTT125C2 - composite grating
6.22
Specification code:Q150SR-BTM (All-304 stainless steel)
With "Smart Secondary Strainer"*SPS 150mm Square Push-in Bucket Trap
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Speciality Plumbing Supplies Pty Ltd
Standard PVC Pipe
"Smart Secondary Strainer"
Strainer basket
Structural slab
30mmMin. height
Tiling or topping
150mmSquare
6.23
185mm
100 N.B.
Also suits copper, C.I.&HDPE pipes
I.D. Rubber ring seal
Square grate in cast 304stainless steel. Basket andstrainer in 304 stainlesssteel sheet.
Spigot fits inside 100mmPVC, copper, CI andHDPE.
Secondary strainer plateactivates only whenstrainer basket is removed.
Compatible with PVC leakcontrol flanges formembraned applications.
SPS
SECTION 7 Cleanouts - Inspection Points - Boundary Traps
7.01
7.02
7.03
7.04
7.05
7.06
7.07
7.08
7.09
7.10
7.11
7.12
7.13
7.14
7.15
130mm Round - Push-in
150mm Round - Push-in
130mm Square - Push-in
117mm Vinyl - Push-in
135mm Vinyl - Push-in
135mm Vinyl - Push-in – Special Plug Insert
130mm Round - Vari-level
150mm Round - Vari-level
125mm Vinyl - Vari-level
155mm Vinyl - Vari-level
200mm Round - Push-in 150 (Boundary Trap)
220mm Vinyl - Push-in 150
220mm Vinyl - vari-level - for sheet vinyl floor
150mm Square - Push-in – Special Trap Screw
150 & 200mm Square Inspection Covers
To suit pipe size (mm):
100
100
100
80
100
100
100
100
100
100
150
150
150 (or 100)
100
100
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
130mmRound
Standard PVC Pipe
SPS 130mm Round Push-in CleanoutSpecification codes:R130SCR4 (Polished 304 stainless steel)R130SCR6 (Satin 316 stainless steel)R130SCRN6 (Non-slip 316 stainless steel)For security screws, use suffix /SEC
Structural Slab
Min. height
Tiling or topping
20mm
100 N.B.
Typical Application
HDPE pipes.Also suits copper, C.I.&
I.D. Rubber ring seal
Cast into slab
SPS
Light-dutycleanout in cast304 and 316stainless steel.
Gas-tight lid.
Security screwsalso available.
7.01
100mm outlet
I.D. 87mm
O.D. 97mm
Optional security screws (use suffix "/SEC")
Typical Application
100 N.B.
SPS 150mm Round Push-in Cleanout
150mmRound
Tiling or topping
Standard PVC Pipe
20mmMin. height
Structural Slab
Specification codes:R150SCR (Satin 316 stainless steel)
SPS
7.02
I.D. Rubber ring seal
Also suits copper, C.I.&HDPE pipes.
100mm Outlet
Heavy-dutycleanout in cast316 stainlesssteel.
Security screwsalso available.
Cast into slab
Optional security screws
I.D. 88mm
O.D. 97mm
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm Outlet
I.D. Rubber ring seal
Also suits copper, C.I.&
SPS 130mm Square Push-in Cleanout
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Min. height
Structural Slab.
Standard PVC Pipe
20mm
Typical Application
100 N.B.
HDPE pipes.
130mmSquare
SPS
7.03
Cast into slabTiling or topping
Light-dutycleanout in cast304 and 316stainless steel.
Gas-tight lid.
Security screwsalso available.
Specification codes:Q130SCR4 (Polished 304 stainless steel)Q130SCRN6 (Non-slip 316 stainless steel)For security screws, use suffix /SEC
Optional tamper-proof screws (use suffix "/SEC")
O.D. 97mm
I.D. 87mm
Specification codes:VH80SPA (304 stainless steel ring & grate, ABS body)V80SPA (All-304 stainless steel assembly)For bead-blast (slip resistant) finish, use suffix -N
SPS 80mm Push-in Sheet Vinyl Floor Cleanout
Ø130mm
7.04
28mm
53mmI.D. 64mm
O.D. 72mm
80mm Pipe
117mm
Typical ApplicationSheet Vinyl
Cement Screed
Structural Slab
SPS
Push-in cleanoutassembly for sheetvinyl flooring.
Vinyl floor drain bodyavailable in ABS and304. 316SS bodyavailable by specialorder.
Ring & grate availablein polished 304, whichcan be bead-blastedfor slip-resistant finish.
O-rings adapt outlet to80mm PVC & copperpipe.
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
7.05
Ø150mm
50mm
I.D. 88mm
O.D. 97mm
25mm
Specification codes:V100SPA (304SS body, polished 304 SS ring & lid)V100SPNA (304SS body, non-slip 304 SS ring & lid)For 316SS tops, add "6" to the above codesFor ABS plastic body, use "VH" instead of "V"
135mm
Cleanout (New Compact Top Model)SPS 100mm Push-in Sheet Vinyl Floor
Structural Slab
Cement Screed
Sheet Vinyl
Push-in floor cleanoutassembly for sheetvinyl flooring.
Drain body available in304 stainless steel -ABS and 316 stainlesssteel options.
Vinyl clamp ring & lidavailable in polishedand non-slip 304stainless steel. 316stainless steelnon-stock option.
O-rings adapt outlet to100mm PVC, copper,HDPE and CI pipe.
Rubber Plug (optional)
Typical Application
100mm Pipe
Optional security screws
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
7.06
Ø150mm
50mm
I.D. 88mm
O.D. 97mm
25mm
Specification codes:V100SP26A (316SS body, satin 316 SS ring & lid)For ABS plastic body, use "VH" instead of "V"
135mm
Cleanout (special "plug insert" version)SPS 100mm Push-in Sheet Vinyl Floor
Structural Slab
Cement Screed
Sheet Vinyl
Push-in floor cleanoutassembly for sheetvinyl flooring.
Drain body available in316 stainless steel orABS plastic. Vinylclamp ring & lidavailable in polished orsatin 316 stainlesssteel.
Cleanout insert sealsinto clamp ring withinternal o-ring seal.
O-rings adapt spigot to100mm PVC, copper,HDPE and CI pipe.
Typical Application
100mm Pipe
Internal o-ring seal
Lever point forplug removal
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Removal of fixingscrews for cleanlinessin lab environments
100mm Outlet
65mm
Light-duty cleanoutassembly made from 316stainless steel. 304stainless steel non-stockoption.
Satin finish standard withoptional special non-slipfinish (concentric ridges).
C100A CI "deluxe" lowerbody with reversibleclamp collar (pictured).
Optional Q100Y CIretro-fit lower body fitsinside 150mmØ corehole.
SPS 130mm Round Vari-Level Cleanout
Optionalcoupling
connection
Membrane flange 235Ø
95mm
Specification codes:R130SC/Q (316 SS cleanout, Q100Y retro-fit lower body)R130SC/C (316 SS grate, C100A CI "deluxe" lower body)For non-slip finish, add suffix "N" eg "R130SPN/C"
**Optional Extension Piece
40
30
Height adjustment:Min. 20mmMax. 50mm**
Push-inconnection
(specify: -R)
100mm N.B.
Typical Application
Weep slots3 x places
Tiling/Paving/Topping
Membrane
130mmRound
SPS
7.07
Q100Y2B retro-fitlower body(optional)
77mm
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm Outlet
65mm
Cleanout assembly madefrom 304 stainless steel.316 stainless steelnon-stock option.
Satin finish standard withoptional non-slip finish(concentric ridges).
C100A CI "deluxe" lowerbody with reversibleclamp collar (pictured).
Optional CI retro-fit lowerbody fits inside 150mmØcore hole.
SPS 150mm Round Vari-Level Cleanout
150mmRound
Membrane flange 235Ø
Optionalcoupling
connection
95mm
**Optional Extension Piece
30
40
Height adjustment:Min. 25mmMax. 60mm** Typical Application
100mm N.B.
Push-inconnection
(specify: -R)
Weep slots3 x places
Tiling/Paving/Topping
Membrane
SPS
7.08
Specification codes:R150SC/Q (304 SS cleanout, Q100Y retro-fit lower body)R150SC/C (304 SS grate, C100A CI "deluxe" lower body)For non-slip finish*, add suffix "N" eg "R150SPN/C"*316SS and non-slip finish both available by special order
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Q100Y2B retro-fitlower body(optional)
77mm
Height adjustment:Min. 20mmMax. 50mm**
95mm
** Optionalextension
piece
Specification codes:LG810SP4/C (304 SS vinyl floor cleanout, CI lower body)LG810SP6/C (316 SS top, 304 SS drain body, CI lower body)* for retro-fit body use "/Q" instead of "/C"
Clamping ring
Weep slots3 x places
65mm
235Ø
Push-inconnection
(specify: -R)
100mm N.B.
Optionalcoupling
connection
30
40
Typical Application
Cement screed
7.09
Q100Y2B retro-fitlower body(optional)
Height-adjustable vinylfloor cleanout assembly.
Vinyl floor body available in 304 stainless steel;316 stainless steelavailable by special order.
Ring & cover available inpolished 304 stainless steel;316 stainless steelavailable by special order.
C100A CI "deluxe" lowerbody with reversible clampingcollar ("/C").
Q100Y optional CI retro fitlower body fits inside150mmØ core hole ("/Q").
77mm
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Ø87
Ø125
Vinyl Sheet
Ultra-compact:Vinyl ClampOD 125mm
SPS 100mm Ultra Compact Vari-LevelSheet Vinyl Floor Cleanout - Ø125mm Inlet
Drain body OD142mm
SPS
Weep slots3 x places
Membrane flange 235Ø
Clamping ring
Sheet Vinyl Floor
65mm
(Vari-Level)
Ø178mm
Ø155mm
SPS 155mm Round Sheet Vinyl Floor Cleanout
Height adjustment:Min. 25mmMax. 50mm**
95mm
** Optionalextension
piece
Specification codes:LG100SP4/C (Polished 304SS top & drain body, CI lower body)LG100SP6/C (Satin 316SS top, 304SS drain body, CI lower body)For retro-fit body use suffix "/Q"
Height-adjustable vinyl floor cleanoutassembly.
Drain body available in 304 stainless steel.316 stainless steel available by specialorder.
Top available in polished 304 stainlesssteel. Satin 316 stainless steel available byspecial order.
C100A CI "deluxe" lower body withreversible clamping collar ("/C").
Optional CI retro fit lower body fits inside150mmØ core hole ("/Q").
100mm N.B.
Typical Application
Optionalcoupling
connection
30
40
Cement screed
Push-inconnection
(specify: -R)
7.10
Membrane
Q100Y2B retro-fitlower body(optional)
77mm
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Standard PVC Pipe
Specification codes:R200/150SCR4 (Polished 304 stainless steel)R200/150SCR (Satin 316 stainless steel) *SPECIAL*R200/150SCRN (Non-slip 316 stainless steel)
Rubber ring seal
SPS 200mm Round Push-in Cleanout
Min. height: 25mm
Tiling or topping
200mmRound
7.11
150mm NB
I.D. 138mm
O.D. 146mm
Typical Application
Also suits copper, C.I.&HDPE pipes.
Structural Slab
Heavy-duty cleanoutin cast 304SS andnon-slip 316SS.Satin 316SSavailable by specialorder.
Security screws alsoavailable.
SPS
(150mm outlet)
Optional security screws (use suffix "/SEC")
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Cast into slab
(150mm Push-in)
Push-in floor cleanoutassembly for sheet vinyl.
Drain body available in304 stainless steel; 316stainless steel non-stockoption.
Lid available in polishedor non-slip 304 stainlesssteel. 316 stainless steelnon-stock option.
SPS 220mm Sheet Vinyl Floor Cleanout
Structural Slab
Standard PVC Pipe
240mm
Specification codes:LG150SPA (Polished 304 stainless steel top)LG150SPNA (Non-slip 304 stainless steel top)For 316 stainless steel, add "6" eg "LG150SPNA6"
Ø220
Min. height: 25mm
Vinyl floor
150mm NB
O.D. 146mm
I.D. 138mm
Typical Applicatioin
Clamp ring
HDPE pipes.
Rubber ring seal
Also suits copper, C.I.&
Cementscreed
SPS
7.12Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9419 0108 E-mail: [email protected]
(Vari-Level)150mm Outlet
or 100mm Outlet
Vinyl floor
100mm outlet shownwith optional couplingconnector
Tiling/Paving/Topping
98mm
Height-adjustable vinylfloor cleanout assembly.
Drain body available in304 stainless steel. 316stainless steel availableby special order.
Lid available in polishedor non-slip 304 stainlesssteel. 316 stainless steelavailable by special order.
150 or 100mm "Truflo" CIlower body with 150mmclamp collar.
SPS 220/150mm Sheet Vinyl Floor Cleanout
** Use EP150 foradditional height
Height adjustment:Min. 28mmMax. 72mm**
86mm
Specification codes:LG150SP/C150 (Polished 304 Stainless steel)LG150SPN/C150 (Non-slip 304 stainless steel)- includes cast iron "Truflo" lower body assembly* for 316 stainless steel use suffix "6" eg "LG150SP6/C150"* for 100mm outlet, use suffix "C100" instead of "C150"
SPSØ220
Typical Application
150 or 100 N.B.
Integral puddle flange Ø270
Membrane
150mm outlet shownwith optional tailpiece
connector
Structural
Clamp ring
Slab
7.13Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
100mm Outlet
Push-in trap screw /inspection openingavailable in 304stainless steel. 316stainless steelnon-stock option.
I.D. Rubber ring seal
Also suits copper, C.I.&
SPS 150mm Square Special Trap Screw
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
3mm thick Vinyl Tiling...
Structural Slab.
Specification code:Q150IOS (304 stainless steel - slip resistant finish)
Standard PVC Pipe
Typical Application
100 N.B.
HDPE pipes.
150mmSquare
7.14
3mm thick platecompatible with 3mmvinyl tiling commonlyused insupermarkets.
... or topping
SPS
4 x countersunk holes as standard
Inspection openingcover available in304 stainless steel.316 stainless steelnon-stock option.
Also suits copper, C.I.&
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
3mm thick Vinyl Tiling...
Structural Slab.
Specification code:IO150S (304 stainless steel)IO200S (304 stainless steel)
Standard PVC Pipe
Typical Application
100 N.B.
HDPE pipes.
150mmor
200mmSquare
7.15
3mm thick platecompatible with 3mmvinyl tiling commonlyused insupermarkets.
... or topping
4 x countersunk holes as standard
SPS 150mm & 200mm Square Inspection Cover
SECTION 8 Security Floor Drains
8.01
8.02
8.03
8.04
8.05
8.06
8.07
8.08
8.09
8.10
8.11
130mm Round - Push-in
150mm Round - Push-in
135mm Vinyl - Push-in
130mm Round - Vari-level
150mm Round - Vari-level
155mm Vinyl - Push-in
120mm Round - Vari-level - Anti-ligature
120mm Round - Vari-level - 90° Outlet - Anti-ligature
125mm Vinyl - Vari-level - Anti-ligature
125mm Vinyl - Vari-level - 90° Outlet - Anti-ligature
125mm Vinyl - Integral Puddle Flange - Anti-ligature
To suit pipe size (mm):
100
100
100
100
100
100
100
50 / 65
100
50 / 65
100
With topping/tiling
Structural Slab
Min. height
Standard PVC Pipe
Tiling or topping
Specification code:R130SHR4 (satin 304 stainless steel)316SS available by special order
SPS 130mm Round Push-in Prison Drain
Installation with puddle flange
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
20mm
Cast into slab
I.D. rubber rings tosuit 100mm PVC,HDPE & copper
Structural Slab
100 N.B.
Typical Applications
8.01
100mm Outlet
130mm round grate with 6mm holes and"hex-head" or "torx" security screws
SPS
I.D. 87mm
O.D. 97mm
Floor waste includessecurity screws and6mm holes forimprovedtamper-resistance.
Grate assemblyavailable in 304stainless steel. 316stainless steelavailable by specialorder.
Pushes into 100mmPVC, copper, HDPEor cast iron.
(100mm Push-in)
Floor waste includesspecial tamper-resistantfeatures for prisons andsafe cells.
Grate assembly availablein 304 stainless steel.
Pushes into 100mm PVC,copper, HDPE or castiron.
SPS 150mm Round Prison / Safe Cell DrainSpecification code:R150SHR4 (satin 304 stainless steel)
Standard PVC Pipe
150mm roundgrate with 6mm
holes and"hex-head" or"torx" security
screws
Structural Slab.
Min. height30mm
Tiling or topping
100 N.B.
Typical Application
I.D Rubber ring seal
HDPE pipes.Also suits copper, C.I.&
8.02Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
8.03
O.D. 97mm
I.D. 88mm
150mm
135mm
50mm
Push-in floor wasteassembly for sheetvinyl flooring.
Grate features securityscrews and 5mmholes.
O-rings adapt spigot to100mm PVC, copper,HDPE and CI pipe.
100mm Pipe
Typical Application
25mmCement Screed
Sheet Vinyl
Structural Slab
(Compact Security/Prison Model)SPS 100mm Push-in Sheet Vinyl Floor Waste
135mm
150mm
Specification codes:VH100SHA (ABS body, 304 stainless steel top)V100SSHA4 (Assembly in 304 stainless steel)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Height adjustment:Min. 20mmMax. 50mm**
30
**Optional Extension Piece
50
Specification codes:R130SH4/E (304SS grate with PVC adapter *not shown*)R130SH/Q (304SS grate, Q100Y2B retro-fit lower body)R130SH/C (304SS grate, C100A CI "deluxe" lower body)
SPS 130mm Round Prison / Safe Cell Drain
Weep slots3 x places
Tiling/Paving/Topping
235Ø
65mm
Push-inconnection
(specify: -R)
100mm N.B.
Optionalcoupling
connection
95mm
Typical Application
8.04
Membrane
Floor waste includessecurity screws and 6mmholes for improvedtamper-resistance.
Grate assembly availablein 304 stainless steel.316SS available by specialrequest.
C100A CI "deluxe" lowerbody with reversible clampcollar (pictured).
Optional Q100Y2B CIretro-fit lower body fitsinside 150mmØ core hole.
(Vari-Level)
SPS
130mm roundgrate with 6mm
holes andtemper-resistant
screws
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Q100Y2B retro-fitlower body(optional)
77mm
Specification codes:R150SH/E (304 SS grate with PVC adapter *Not shown*)R150SH/Q (304 SS grate, CI retro-fit lower body)R150SH/SQ (304 SS grate, SS retro-fit lower body)R150SH/C (304 SS grate, C100A CI "deluxe" lower body)
Height adjustment:Min. 25mmMax. 60mm**
**Optional Extension Piece
SPS 150mm Round Prison / Safe Cell Drain
Typical Application
Weep slots3 x places
235Ø
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Ø145
Optionalretro-fit
lower body 95
65mm
100mm N.B.
Push-inconnection
(specify: -R)Optionalcoupling
connection40
30
95mm
8.05
Tiling/Paving/Topping
Membrane
100mm outlet
150mm roundgrate with 7mm
holes andtemper-resistant
screws
* SPECIAL ORDER PRODUCT * Floor waste includes specialtamper-resistant features forprisons and safe cells.
Grate assembly available in304 stainless steel.
C100A CI "deluxe" lowerbody with reversible clampcollar (pictured).
Optional CI or SS retro-fitlower body fits inside150mmØ core hole.
(Vari-Level)
8.06
95
65mm
SPS 100mm Sheet Vinyl Prison Floor Waste
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
235Ø
95mm
Cement screed
Optionalcoupling
connection
Height-adjustable vinyl floor waste assembly.
High-security features: 7mm holes andtamper-resistant screws.
Drain body available in bronze or316 stainless steel.
Ring & Grate available in 304 grade stainlesssteel. 316 stainless steel non-stock option.
C100A CI "deluxe" lower body with reversibleclamping collar.
Specification codes:
LG100SH/C (304 stainless steel floor waste, CI lower body)for retro-fit lower body, use "/Q" instead of "/C"
** Optionalextension
piece
30
50
Height adjustment:Min. 25mmMax. 50mm**
Push-inconnection
(specify: -R)
100mm N.B.
Typical Application
Weep slots3 x places
Ø145
Optionalretro-fit
lower body
Clamping ring
Sheet Vinyl Floor
Membrane
(Vari-Level)LG100SH/E (304 SS grate with PVC adapter *Not shown*)
Specification codes:R120S-ACR/E (304 SS grate with PVC adapter *Not shown*)R120S-ACR/C (with C100A cast iron "deluxe" lower body)R120S-ACR/Q (with Q100Y2B cast iron retro-fit body)
Height adjustment:Min. 25mmMax. 60mm**
SPS 120mm Round Prison Floor Waste
95mm
** Optionalextension
piece
Membrane
Weep slots3 x places
235Ø
65mm
Push-inconnection
(specify: -R)
100mm N.B.
Optionalcoupling
connection50
30
5mm slots
Topping / Tiling
Concealed waterway
8.07
Heavy-duty, long-lastingall-304 stainless steel floorwaste assembly.
New "Anti-Crocodile-Roll"features, includingconcealed waterways withno anchor points.
Includes "Pin-Hex" stylesecurity screws. Otherversions optional, including"Torx" and "Snake-eye"style.
C100A CI "deluxe" lowerbody with reversible clampcollar.
Q100Y2B retro-fit lowerbody for in-slab leak control
(100mm Vari-Level)
Typical Application
120mmRound
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Q100Y2B retro-fitlower body(optional)
77mm
"ACR"
Topping or Tiling
Structural Slab
'A'
SPS R120mm Round "ACR" Side Outlet PrisonSpecification codes:R120S-ACR4/C90 (Satin 304 stainless steel)Includes Q165/90Y 65/50mm CI side outlet lower body
Min. height 25mm
N.B
DCB
10095
6550
1518
200200
180180
'D'
Spigot pushes into 65mm PVC or copper with o-ring connection,or connects to 50mm PVC/HDPE with no-hub coupling.
'C'
AN.B.
8.08
'B'
(100x65/50mm)
Heavy-duty, long-lasting all304 stainless steel floorwaste assembly.
New "Anti-Crocodile-Roll"features, includingconcealed waterway and noanchor points.
Several types of securityscrew are available,including "torx" style and"snake-eye" style.
Q165/90Y cast iron sideoutlet lower body connectsto 65mm and 50mm pipe.
Typical Applications
120mmRound
Floor Waste
5mm slots
Concealed waterway
Dimensions (mm)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Specification codes:LG810SSA-ACR4/E (304 SS grate with PVC adapter *Not shown*)LG810SSA-ACR4/C (with C100A "deluxe" CI lower body)LG810SSA-ACR4/Q (with Q100Y2B retro-fit CI lower body)
Typical Application
Heavy-duty, long-lasting all304 stainless steel vinylfloor waste assembly.
New "Anti-Crocodile-Roll"features, includingconcealed waterway and noanchor points.
Several types of securityscrew are available,including "torx" style and"snake-eye" style.
C100A CI "deluxe" lowerbody with reversible clampcollar.
Q100Y2B retro-fit lowerbody for in-slab leak control
Vinyl Floor Waste (100mm Vari-Level)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
SPS 100mm "ACR" Ultra Compact Prison
Drain body OD142mm
Membrane flange 235Ø
95mm
50
** Optionalextension
piece
30
65mm
Q100Y2B retro-fitlower body(optional)
Optionalcoupling
connection 100mm N.B.
Push-inconnection
(specify: -R)
Weep slots3 x places
77mm
Cement screed
Min. height 18mm
Concealed waterway
125mm
5mm slotSheet Vinyl Floor
8.09
Structural Slab
'A'
SPS 100mm "ACR" "Ultra Compact"
Specification codes:LG810SSA-ACR4/C90 (Satin 304 stainless steel)Includes Q165/90Y 65/50mm CI side outlet lower body
Min. height 18mm
N.B
DCB
10095
6550
1518
200200
180180
'D'
Spigot pushes into 65mm PVC or copper with o-ring connection,or connects to 50mm PVC/HDPE with no-hub coupling.
'C'
AN.B.
8.10
'B'
(100x65/50mm)
Heavy-duty, long-lasting all304 stainless steel floorwaste assembly.
New "Anti-Crocodile-Roll"features, includingconcealed waterway and noanchor points.
Several types of securityscrew are available,including "torx" style and"snake-eye" style.
Q165/90Y cast iron sideoutlet lower body connectsto 65mm and 50mm pipe.
Typical Applications
Prison Vinyl Floor Waste Side Outlet
Dimensions (mm)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Concealed waterway
125mm
5mm slotSheet Vinyl Floor
Drain body OD142mm
Standard PVC Pipe
Structural Slab
Min. Height 20mm
SPS 100mm Retro-fit Puddle Flangewith Slip-in "ACR" Prison Vinyl Floor Waste
Specification code:LG87SVA-ACR4/PF (ABS body, Satin 304SS top)Includes PF100 lo-profile puddle flange
Screed
Flange OD180mm
Sheet vinyl flooring
Waterproof membrane
1mm spacer fins (x8)
I.D Rubber ring seal
Also suits copper, C.I.&
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Typical Application
I.D. 81mm
1mm spacer fins (x4)
125mm
100mm N.B.
Concealed waterway
HDPE pipes.
8.11
Retro-fit puddle flangewith ultra-thin face.
Lo-profile vinyl floorwaste slips inside I.D. offlange. 1mm spacer finsprovides adequate leakcontrol.
Satin 304-grade stainlesssteel ring and grate.
"ACR" security featuresinclude concealedwaterway and "hex-head"security screws.
Drain body OD142mm
SECTION 9 Specials & Miscellaneous
9.01
9.02
9.03
9.04
9.05
9.06
9.07
9.08
9.09
9.10
9.11
100mm Drop-in Balcony Drains
Retro-fit Membrane Flange with Flat or Dome Grate
Special 90° Balcony Drain with Flat or Dome Grate
200mm Square Downpipe Drain - Push-in
200mm Square Downpipe Drain - Vari-level
225mm Round Downpipe Drain - Vari-level
225mm Square Downpipe Drain - Vari-level
100mm Truflo RWO – recessed flat grate for under downpipes
The Balcony Box
Custom Stainless Steel Grate & Trough - Standard
Custom Stainless Steel Grate & Trough - Vinyl Clamp
To suit pipe size (mm):
65
100
50 / 65
100
100 (or 150)
100 (or 150)
150
100 & 150
100
100
100
Round or square grate availablein 316 stainless steel. 304stainless steel non-stock option.
50mm spigot drops inside 65mmpipe after liquid membrane hasbeen applied into pipe.
To be employed only with theapproval of the waterproofingcontractor.
Extra precautions must beemployed to prevent tile bedding /grout from blocking the outlet.
120 Min.
SPS 100x50mm Special Drop-in Balcony Drain
Min. Height 20mm
Membrane
Specification codes:R100S2 (Round 316 stainless steel grate)Q100S2 (Square 316 stainless steel grate)
Ø65mm PVCor copper bend
Typical Application
Structural Slab
100mmRound
SPS
Tiling or Topping
100mmSquare
SPS
9.01Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
Standard PVC Pipe
Structural Slab
Clamping flange 190mm O.D.
9.02
Also suits copper, C.I.&
100mm N.B.
HDPE pipes.
Typical Application
I.D Rubber ring seal
Membrane
Domed grate 155mm O.D.
Weep slots x 3
SPS
20mm
SPS 100mm Retro-fit Dome/Flat Grate & FlangeSpecification code:
RC100AD (304 s/s flange, aluminium domeRC100AF (304 s/s flange, aluminium flat grate
65/50mm outlet
Membrane
'B'
N.B
SPS Special Dome/Flat 90° Balcony Drain
Timber Decking / Suspended Paver System
'A'
Typical Application
'D''C'
Spigot pushes into 65mm PVC or copper with o-ring connection, orconnects to 50mm PVC/HDPE with no-hub coupling.
Structural Slab
Weep Holes3 x places
Special flat or domegrate adapts to sideoutlet balcony drainbody.
Suitable forwaterproofed balconies /podia with timberdecking or suspendedpaver systems.
9.03Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
SPS
10510050
65
N.B.4037
A B180180
C200200
D
Specification code:C50/90AD (ABS lower body, LM6 aluminium dome)C50/90AF (ABS lower body, LM6 aluminium flat grate)
20mm
Specification code:Q200SRDP (satin 316 stainless steel) *Nonstock optionQ200SRDP4 (polished 304 stainless steel)
Installation with puddle flange
SPS 200mm Square Push-in Floor Drain
I.D. rubber ringseals to suit
100mm PVC,HDPE & copper
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
100 N.B.
30mm
Standard PVC Pipe
Structural Slab
Tiling or topping
Min. height
Typical Applications
Structural Slab
100mm Outlet
High-heel friendly pattern (6mm gaps)
200mmSquare
With topping/tiling Cast into slab
**Downpipe Version**
Ø120mmHole
** Suitable forLOW-FLOW
applications only
**SPS Recommends theHI-FLOW versionQ200/150SDP4
9.04
Height adjustment:Min. 30mmMax. 95mm*
Specification code:Q200SDP4/C100 (Polished 304 SS grate assembly, CI lower body)Q200SDP6/C100 (Satin 316 SS grate & frame ass'y, CI lower body)For 150mm outlet, use suffix "C150" not "C100"
SPS 200mm Square Downpipe Drain
98mm
Tiling/Paving/Topping
100mm outlet shownwith optional couplingconnector
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
150mm outlet shownwith optional tailpiece
connector
Integral puddle flange Ø270
150 or 100 N.B.
Structural
Membrane
Slab
Downpipe
9.05
100mm Outlet 150mm Outlet
Height-adjustablehigh-heel friendly grateassembly.
Grate assembly features120Ø hole to allowinsertion of 110mmdownpipe.
Double-hinge design forease of access andmaintenance.
Available in 304 or 316stainless steel.
100mm or 150mm TrufloCI lower body with150mm reversible clampcollar.
Specification code:R225SDP4/C100 (Polished 304 SS grate assembly, CI lower body)R225SDP6/C100 (Satin 316 SS grate & frame ass'y, CI lower body)For 150mm outlet, use suffix "C150" not "C100"
SPS 225mm Round Special Downpipe Drain
Structural
150mm outlet shownwith optional tailpiece
connector
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
Membrane
Height adjustment:Min. 30mmMax. 70mm
98mm
Tiling/Paving/Topping
100mm outlet shownwith optional couplingconnector
Integral puddle flange Ø270
150 or 100 N.B.
Downpipe
Slab
9.06
100mm Outletor 150mm Outlet
Height-adjustablehigh-heel friendly grateassembly.
Grate assembly features120Ø hole to allowinsertion of 110mmdownpipe.
Available in 304. Note 316is available on request.
100mm or 150mm TrufloCI lower body with150mm reversible clampcollar.
120mmHole
225mmRound
Height adjustment:Min. 30mmMax. 95mm*
Specification code:Q225SDP4/C150 (Polished 304 SS grate assembly, CI lower body)Q225SDP6/C150 (Satin 316 SS grate & frame ass'y, CI lower body)For 100mm outlet, use suffix /C100*316SS version is SPECIAL ORDER*
SPS 225mm Square Special Downpipe Drain
98mm
Tiling/Paving/Topping
100mm outlet shownwith optional couplingconnector
150mm outlet shownwith optional tailpiece
connector
Integral puddle flange Ø270
150 or 100 N.B.
Structural
Membrane
Slab
150mm outletor 100mm outlet
Height-adjustablehigh-heel friendly grateassembly.
Grate assembly features170mmØ hole to allowinsertion of 160mmdownpipe.
Double-hinge design forease of access andmaintenance.
Available in 304 stainlesssteel; 316 stainless steelavailable by special order.
100mm or 150mm TrufloCI lower body with150mm reversible clampcollar.
Downpipe (max O.D. 160mm)
225mmSquare
Ø170mm
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] 9.07
Flat grate in LM-6aluminium
75mm
Optional concretesurround (by others)
Specification codes:T3150/100FE (Aluminium grate, galvanised CI body, 100mm outlet)T3150FE (Aluminium grate, galvanised CI body, 150mm outlet)
SPS 100 & 150mm Truflo SpecialDownpipe Discharge Drain
Tel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected] Plumbing Supplies Pty Ltd
HD stainless steelfixing screws (x2)
40mm
100mm PVCspigotadapter
110mm ØDownpipe(by others)
N.B
Grate recessed 16mm inside body
150mm PVCspigotadapter
9.08
Suggested application:Rainwater inlet to beinstalled beneath thedownpipes.
S P S
Typical Application
250mmØ Body madefrom hot-dipped
galvanised cast iron
SPS 100mm Dual Inlet Balcony BoxSpecification codes:BB100 (injection-moulded uPVC plastic)
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 Email: [email protected]
100mm
160m
m
380mm
80mm
Standard 100mm Socket Outlet
100mm Downpipe(hole cut on-site)
100mm Floor waste (hole cut on-site)
Typical Application
Structural Slab
Tiling / Topping
Downpipe and floor waste inlets cuton site to fit as needed
Membrane
151mm
151mm
Weep holes cut on site by installer
100mm N.B.
9.09
SPS S/S Custom size grate & trough
· Available with standard outlet or dual strainer basket trap
· HEELGUARD 304 s/s grating -3mm wedgwire x 5mm gap
· Load Class 'B' under AS3996
· Dimpled non slip 316 s/swedgewire available at extra cost
· Full 304-grade s/s construction
· 316-grade also available at extracost
· Cross-break to outlet standard
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
As required
Outlet 88.9mm Ø
As required
As required
PLAN
FRONT ELEVATION
As required
Pressedsafetyedge
As required
As required
3mm 5mm
Various
Deeper applications
With S/S wedge wire gratingSpecification codes:SSTCUST - standard wedge-wire grating and channel
3mm 5mm
Shallow applications
As requireed
As required
9.10
HEELGUARD slip resistant grating
Class 'B' loading rating to AS3996-2006Higher load ratings available on request
Removable dual strainer basket trap orstandard outlet available
Full 304-grade s/s construction. 316 s/savailable on request
Cross-break to outlet or fall to outletavailable
Speciality Plumbing Supplies Pty LtdTel: (02) 9417 1900 Fax: (02) 9417 0108 E-mail: [email protected]
As required
Outlet 89mm Ø x 100mm longDual strainer basket trap
As required
As required
FRONT ELEVATION
5mm
Grate Section
Vinyl clamp edge
Trough Section
Cross break
As requiredVarious
Nut serts @ 300 cntrs
27mm
150mm 300mm
Vinyl clampfixings
27mm
As required
SPS S/S Custom grate & trough with wedge wire grate - vinyl clamp edge
3mm
Specification codes:SSTVCUST - standard wedge-wire grating
9.11
Appendix
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA100F
Weir Flow 7 L/s (30mm)
Observation Comments: Flow rates from 0-7.0 L/s (30mm Head) produced a linear characteristic curve with stable water
head levels. At 8.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 10mm. At 10.0 14.0 L/s the flow surcharged with the water head fluctuating 30mm. The maximum flow limit to maintain weir flow conditions is 7.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA150F
Weir Flow 6.0 L/s (35mm) Orifice flow 10 L/s (40mm)
Observation Comments: Flow rates from 0-6.0 L/s (35mm Head) produced a linear characteristic curve with stable water
head levels At 8.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow At 10.0 14.0 L/s the flow surcharged characterised by the water level fluctuating 10 20 mm. The maximum flow limit to maintain weir flow conditions is 6.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
0
10
20
30
40
50
60
70
80
0 2 4 6 8 10 12 14
Wat
er H
ead
Leve
l (m
m)
Flow Rate (L/s)
TRANSITION FLOW REGIONPlease note that the water depth levels in this
shaded area of the chart were observed to fluctuate continuously between maximum and minimum levels due to the transition between weir and orifice flow conditions occurring at
the outlet. Only the maximum observed water levels are plotted on this
chart.
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA100F2
Weir Flow 8 L/s (30mm)
Surcharged flow 12 L/s (90mm)
Observation Comments: Flow rates from 0-8.0 L/s (30mm Head) produced a linear characteristic curve with the exception
of open outlet which increased water head level rapidly at 6.0 L/s. At 10.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 20mm. At 12.0 14.0 L/s the flow surcharged with the water head fluctuating 40mm. The maximum flow limit to maintain weir flow conditions is 8.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA150F2
Weir Flow 6 L/s (30mm)
Surcharged Flow 10 L/s (40mm)
Observation Comments: Flow rates from 0-6.0 L/s (30mm Head) produced a linear characteristic curve with stable water
head levels. At 8.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 10.0 14.0 L/s the flow surcharged characterised by the water level fluctuating 10 - 20mm. The maximum flow limit to maintain weir flow conditions is 6.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 2: 1 Authorised by Dr Terry Lucke 7-6-2017 2
Flow Characteristic Curve TIA100D2
Weir Flow 8 L/s (37mm)
Surcharged Flow >12 L/s
Observation Comments: Flow rates from 0-8.0 L/s (37mm Head) produced a linear characteristic curve with the exception
of open outlet which increased water head level rapidly at 8.0 L/s. At 10.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 20mm. Above 12.0L/s the flow surcharged. The maximum flow limit to maintain weir flow conditions is 8.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 7th June 2017
Mark Alexander, AHSCA Foundation Chairman:
Date: 7th June 2017
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA150D2
Weir Flow 8 L/s (30mm)
Surcharged Flow 12 L/s (40mm)
Observation Comments: Flow rates from 0-8.0 L/s (30mm Head) produced a linear characteristic curve with stable water
head levels. At 10.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 10.0 14.0 L/s the flow surcharged characterised by the water level fluctuating 10 - 20mm. The maximum flow limit to maintain weir flow conditions is 8.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA80/90F
Weir Flow 1.5 L/s (6mm)
Surcharged Flow 3 L/s (22mm)
Observation Comments: Flow rates from 0-1.5 L/s (6mm Head) produced a flat characteristic curve with stable water head
levels. At 2.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 3.0 4.0 L/s the flow surcharged with the water head rising rapidly to 90mm. The maximum flow limit to maintain weir flow conditions is 1.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA100/90F
Weir Flow 3 L/s (15mm)
Surcharged flow 4 L/s (20mm)
Observation Comments: Flow rates from 2.0-3.0 L/s (15mm Head) produced a flat characteristic curve with stable water
head levels. At 4.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 5.0 7.0 L/s the flow surcharged with the water head rising rapidly to 100mm. The maximum flow limit to maintain weir flow conditions is 3.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA80/90F2
Weir Flow 1.5 L/s (8mm)
Surcharged Flow 3 L/s (20mm)
Observation Comments: Flow rates from 0-1.5 L/s (8mm Head) produced a flat characteristic curve with stable water head
levels. At 2.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 3.0 4.0 L/s the flow surcharged with the water head rising rapidly to 90mm. The maximum flow limit to maintain weir flow conditions is 1.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA100/90F2
Weir Flow 3 L/s (13mm)
Vortex/surcharged flow 4 L/s (20mm)
Observation Comments: Flow rates from 2.0-3.0 L/s (13mm Head) produced a flat characteristic curve with stable water
head levels. At 4.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 5.0 7.0 L/s the flow surcharged with the water head rising rapidly to 90mm. The maximum flow limit to maintain weir flow conditions is 3.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA80/90D2
Weir Flow 1.5 L/s (7mm)
Surcharged Flow 3 L/s (20mm)
Observation Comments: Flow rates from 0-1.5 L/s (7mm Head) produced a flat characteristic curve with stable water head
levels. At 2.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 3.0 4.0 L/s the flow surcharged with the water head rising rapidly to 90mm. The maximum flow limit to maintain weir flow conditions is 1.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve TIA100/90D2
Weir Flow 3 L/s (12mm)
Surcharged flow 5 L/s (30mm)
Observation Comments: Flow rates from 2.0-3.0 L/s (12mm Head) produced a flat characteristic curve with stable water
head levels. At 4.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 5.0 7.0 L/s the flow surcharged with the water head rising rapidly to 80mm. The maximum flow limit to maintain weir flow conditions is 3.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 24-1-2017 2
Flow Characteristic Curve SIA150F
Weir Flow 10.0 L/s (25mm)
Surcharged Flow 14 L/s (35mm)
Observation Comments: Flow rates from 0-10.0 L/s (25mm Head) produced a flat characteristic curve with stable water
head levels. At 12.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged
flow, then choking btween 14.0-20.0 L/s and the water head rising to 50mm. The maximum flow limit to maintain weir flow conditions is 10.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 24th January 2017
Mark Alexander, AHSCA Foundation Chairman:
Date: 24th January 2017
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 17-1-2017 2
Flow Characteristic Curve SIA150D2
Weir Flow 18 L/s (42mm)
Surcharged Flow - 20 L/s (40mm)
Observation Comments: Flow rates from 0-18.0 L/s (42mm Head) produced a flat characteristic curve with stable water
head levels. At 20.0 22.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged
flow. The maximum flow limit to maintain weir flow conditions is 18.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 17th January 2017
Mark Alexander, AHSCA Foundation Chairman:
Date: 17th January 2017
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve PD50CS
Weir Flow 0.75 L/s (22mm)
Surcharged Flow 1 L/s (30mm)
Observation Comments: Flow rates from 0-0.75 L/s (22mm Head) produced a flat characteristic curve. At 1.0 L/s the weir flow transitioned to surcharged flow with the water head rising rapidly to 60mm
at 1.5 L/s. The maximum flow limit to maintain weir flow conditions is 0.75 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve PD80CS
Weir Flow 2 L/s (50mm)
Surcharged Flow 3.5 L/s (120mm)
Observation Comments: Flow rates from 0-2.0 L/s (50mm Head) produced a flat characteristic curve with weir flow
conditions. At 2.5 L/s the weir flow transitioned to vortex flow, then to surcharged flow at 3.5 L/s (120mm)
characterised by a sudden priming of the outlet and water level flucuating 50mm. The maximum flow limit to maintain weir flow conditions is 2.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve PD100CS
Weir Flow 4.0 L/s (80mm)
Vortex Flow 10.0 L/s (115mm)
Observation Comments: Flow rates from 0-4.0 L/s (80mm Head) produced a flat characteristic curve with weir flow
conditions. At 5.0 L/s the weir flow transitioned to vortex flow, and remained in vortex flow up to 10.0 L/s
(115mm). The maximum flow limit to maintain weir flow conditions is 4.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve - Q100/80SR
Weir Flow 0.75 L/s (14 mm)
Orifice Flow 1.5 L/s (50 mm)
Observation Comments: Flow rates from 0 - 0.75 L/s (14 mm Head) produced a linear characteristic curve. At 1.0 L/s the weir flow transitioned to orifice flow conditions. Flow rates between 1.0 - 2.0 L/s were observed to fluctuate bewteen wier and orifice conditions.
The maximum stable water level achieved was 70 mm at a flowrate of 2.0L/s. Increasing the flowrate beyond this value caused the tank to surcharge.
The maximum flow limit to maintain weir flow conditions was 0.75 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve - R130SR4
Weir flow - 1 L/s (40mm)
Orifice Flow - 3.0 L/s (80mm)
Observation Comments: A concentric swirl pattern and air core was observed which indicated weir flow conditions, with
the water head level stabilising at each flow rate setpoint from 0-2.0 L/s producing a linear characteristic curve for all outlet pipe connections.
At 3.0 L/s a transition from swirl motion to vortex flow was obvserved, as the air core decreased and moved to the side of the grate. At 3.0 L/s the vortex surcharged and transitioned to orifice conditions were characterised by the water level surging down 10 -20mm.
The maximum flow limit to maintain weir flow conditions is 2.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q130SR4
Weir flow - 1 L/s (20mm)
Surcharged flow 3 L/s (65mm)
Observation Comments: Flow rates from 0-2.5 L/s (55mm Head) produced a linear characteristic curve. At 3.0 - 3.5 L/s
the weir flow transitioned to vortex flow, then surcharged with the head level stabilising at 55mm. From 3.5 - 5 L/s the flow conditions cycled between vortex and surcharged flow characterised by
the water level fluctuating 20mm. The maximum flow limit to maintain weir flow conditions is 2.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve - R150SR4
Weir flow - 1 L/s (25mm)
Surcharged flow 3 L/s (75mm)
Observation Comments: Flow rates from 0-2 L/s (60mm Head) produced a linear characteristic curve. At 2.5 L/s the weir
flow transitioned to vortex flow with the head level stabilising at 55-60mm. Flow rates from 3-5 L/s the vortex surcharged and transitioned to orifice conditions, characterised
by the water level fluctuating 10 -20mm. The maximum flow limit to maintain weir flow conditions is 2.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q150SR4
Weir flow - 2 L/s (35mm)
Surcharged flow - 3 L/s (40mm)
Observation Comments: Flow rates from 0-2.0 L/s (35mm Head) produced a linear characteristic curve. At 2.5 - 3.0 L/s
the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow characterised by the water level fluctuating 20mm.
At 4.0 L/s the flow surcharged and stabilised at 30mm head level. Flowrates between 5-6 L/s produced surcharged flow conditions with the water head rising
steadily and stabilising. The maximum flow limit to maintain weir flow conditions is 2.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q200SR4
Weir Flow 2 L/s (20mm)
Surcharged Flow 4 L/s (27mm)
Observation Comments: Flow rates from 0-2.0 L/s (20mm) produced a linear characteristic curve which began to flatten at
2.5 L/s. At 3.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 10mm. At 4.0 L/s the flow surcharged . Flowrates between 5-8 L/s produced surcharged flow conditions with the water head rising rapidly
or fluctuating 40mm with the vertical pipe. The maximum flow limit to maintain weir flow conditions is 2.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q200/150SR
Weir Flow 4 L/s (25mm)
Surcharged Flow 6 L/s (30mm)
Observation Comments: Flow rates from 0-4.0 L/s (25mm Head) produced a linear characteristic. At 5.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 10mm. Flowrates between 6.0-12.0 L/s produced surcharged flow conditions with the water head rising
rapidly to 80mm. The maximum flow limit to maintain weir flow conditions is 4.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve R225SR4
Weir flow - 1 L/s (10mm)
Surcharged flow 3 L/s (30mm)
Observation Comments: Flow rates from 0-2.5 L/s (35mm Head) produced a linear characteristic curve. At 3.0 L/s the weir flow transitioned to vortex flow, then surcharged . From 3.5 - 6 L/s the flow
conditions cycled between vortex and surcharged flow characterised by the water level fluctuating 10 -20mm.
The maximum flow limit to maintain weir flow conditions is 2.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q225/150SR4
Weir Flow 2.5 L/s (20mm)
Surcharged Flow 6 L/s (40mm)
Observation Comments: Flow rates from 0-2.0 L/s (20mm Head) produced a linear characteristic curve which began to
flatten at 2.5 L/s. At 3.0-4.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged
flow characterised by the water level fluctuating 5mm. Flowrates between 5-10 L/s produced surcharged flow conditions with the water head rising
rapidly to 90mm. The maximum flow limit to maintain weir flow conditions is 2.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve R150S4/C
Weir Flow 2.5 L/s (50mm)
Surcharged flow 4 L/s (30mm)
Observation Comments: Flow rates from 0-2.5 L/s (50mm) produced a linear characteristic curve which begain to flatten
at 2.5 L/s. At 3.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 20mm. At 4.0 L/s the flow surcharged and stabilised at 30mm head level. Flowrates between 5-6 L/s produced surcharged flow conditions with the water head fluctuating
40mm. The maximum flow limit to maintain weir flow conditions is 2.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q200S4/C
Weir Flow 2.0 L/s (20mm) Orifice flow 4.0 L/s (30mm)
Observation Comments: Flow rates from 0-2.0 L/s (20mm Head) produced a linear characteristic curve which began to
flatten at 2.5 L/s. At 3.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 10mm. At 4.0 L/s the flow surcharged. Flowrates between 5.0-8.0 L/s produced surcharged flow conditions with the water head rising
rapidly or fluctuating 40 mm with the vertical pipe. The maximum flow limit to maintain weir flow conditions is 2.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
0
20
40
60
80
100
120
140
0 1 2 3 4 5 6 7 8
Wat
er H
ead
Leve
l (m
m)
Flow Rate (L/s)
TRANSITION FLOW REGIONPlease note that the water depth levels in this shaded area of
the chart were observed to fluctuate continuously between maximum and minimum levels due to the transition between weir and orifice flow conditions occurring at the outlet. Only
the maximum observed water levels are plotted on this chart.
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve R225S4C
Weir Flow 2.5 L/s (15mm)
Surcharged flow 4 L/s (30mm)
Observation Comments: Flow rates from 0-2.5 L/s (15mm Head) produced a linear characteristic curve which began to
flatten at 2.5 L/s. At 3.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 10mm. At 4.0 L/s the flow surcharged and stabilised at 30mm head level. Flowrates between 5-8 L/s produced surcharged flow conditions with the water head fluctuating
40mm. The maximum flow limit to maintain weir flow conditions is 2.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Weir Flow 4 L/s (25mm)
Orifice Flow 6 L/s (30mm)
Observation Comments: Flow rates from 0-4.0 L/s (25mm Head) produced a linear characteristic. At 5.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow
characterised by the water level fluctuating 10mm. Flowrates between 6.0-12.0 L/s produced surcharged flow conditions with the water head rising
rapidly to 80mm. The maximum flow limit to maintain weir flow conditions is 4.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve R225S4/C150
Weir Flow 2.5 L/s (20mm)
Surcharged Flow 6 L/s (40mm)
Observation Comments: Flow rates from 0-2.0 L/s (20 mm Head) produced a linear characteristic curve which began to
flatten at 2.5 L/s. At 3.0 - 4.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged
flow characterised by the water level fluctuating 5 mm. Flowrates between 5-10 L/s produced surcharged flow conditions with the water head rising
rapidly to 90 mm. The maximum flow limit to maintain weir flow conditions is 2.5 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q225S/C150
Weir Flow 6 L/s (18mm)
Surcharged Flow 10 L/s (40mm)
Observation Comments: Flow rates from 0-6.0 L/s (18mm Head) produced a linear characteristic curve which began to
level out at 8.0 L/s. At 8.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 10.0 14.0 L/s the flow surcharged with the water head rising to rapidly to 75mm. The maximum flow limit to maintain weir flow conditions is 6.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve R300S/C150
Weir Flow 7 L/s (25mm)
Surcharged Flow 12 L/s (40mm)
Observation Comments: Flow rates from 0-7.0 L/s (25mm Head) produced a linear characteristic curve which began to
level out at 7.0 L/s. At 8.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 10.0 14.0 L/s the flow surcharged with the water head rising to rapidly to 60mm. The maximum flow limit to maintain weir flow conditions is 7.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q300D/150C
Weir Flow 7 L/s (18mm)
Surcharged Flow 12 L/s (25mm)
Observation Comments: Flow rates from 0-7.0 L/s (18mm Head) produced a linear characteristic curve which began to
level out at 7.0 L/s. At 8.0 L/s the weir flow transitioned to vortex flow, cycling between vortex and surcharged flow. At 10.0 14.0 L/s the flow surcharged with the water head rising to rapidly to 50mm. The maximum flow limit to maintain weir flow conditions is 7.0 L/s.
I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve R100S4/C90
Weir flow - 1.0 L/s (60mm)
Surcharged Flow - 2.5 L/s (110mm)
Observation Comments: A concentric swirl pattern was observed which indicated weir flow conditions, with the water head
level stabilising at each flow rate setpoint from 0-2.0 L/s. At 2.5 L/s a transition from swirl motion to vortex flow was observed, as the air core decreased to
approximately 20mm Diameter, followed by a sudden increase in water head level as the vortex collapsed to surcharged orifice flow.
The maximum flow design limit to maintain weir flow conditions is 2.0 L/s. I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve R130S4/C90
Weir flow 1 L/s (50mm)
Surcharged Flow - 3.0 L/s (110mm)
Observation Comments: A concentric swirl pattern and air core was observed which indicated weir flow conditions, with
the water head level stabilising at each flow rate setpoint from 0-2.0 L/s. At 2.5 L/s a transition from swirl motion to vortex flow was observed, as the air core decreased to
approximately 10mm Diameter and moved to the side of the grate. At 3-3.5 L/s the vortex surcharged and transitioned to orifice conditions characterised by the water level surging between 40-100mm at constant flow rates above 3 L/s.
The maximum flow limit to maintain weir flow conditions is 2.0 L/s. I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016
Association of Hydraulic Services Consultants Australia Research Foundation
Outlet Performance Certificate - Revision 1: 1 Authorised by Dr Terry Lucke 16-11-2016 2
Flow Characteristic Curve Q130S4/C90
Weir flow - 1 L/s (50mm)
Surcharged Flow - 2.5 L/s (110mm)
Observation Comments: A concentric swirl pattern was observed which indicated weir flow conditions, with the water head
level stabilising at each flow rate setpoint from 0-2.0 L/s. At 2.5 L/s a transition from swirl motion to vortex flow was observed, as the air core decreased to
approximately 10mm Diameter and moved to the side of the grate. At 3.0 L/s the vortex surcharged and transitioned to orifice conditions were characterised by the water level surging between 30-90mm.
The maximum flow limit to maintain weir flow conditions is 2.0 L/s. I hereby certify that the test results presented on this outlet performance certificate are true and correct and were obtained using recognised AHSCA Gutter Outlet Testing procedures. Dr Terry Lucke, Chief Researcher: Date: 16th November 2016
Mark Alexander, AHSCA Foundation Chairman:
Date: 16th November 2016