600E2 Product Guide Imperial

National Crane 600E2 SeriesProduct Guide

Features

27,4 m (90 ft) four-section boom

18,1 t (20 USt) rating

Self-lubricating Easy Glide wear pads

Internal anti-two block

Features

Four-section boomAt 90 ft, the Series 600E2 four-section boom is the longest in its size range. The long boom allows the operator to perform more lifts without the use of a jib, reducing setup time and improving efficiency.

Easy Glide boom wear padsEasy Glide boom wear pads reduce the conditions that cause boom chatter and vibration. The net result is smoother crane operation.

National Crane Series 600E216,3 t (18 USt) maximum capacity 36,9 m (121 ft) maximum vertical reach 24,7 m (81 ft) maximum vertical hydraulic reach

OutriggersThe Series 600E2 comes equipped with A-frame outriggers and ASH rear stabilzers. An optional single front stabilizer is available for 360 stability. Rear stabilizers include an independent stabilizer control and bolt/clamp-on mounting. Outriggers are equipped with a motion alarm and an outrigger monitoring system.Front:6,73 m (22.08 ft) spanRear:3 m (10 ft) span

Features

Best in class performance and serviceability

The steel torsion box and flatbed further reduce frame flex

Speedy-reeve boom tip and sheave blocks simplify rigging changes by decreasing the time needed to change line reeving

Crane components painted before assembly reduce the chance of rust, improve serviceability and enhance the appearance of the crane

A control knob located on the swing motor brake release valve can be easily adjusted to the crane operators swing speed preference

Engine start/stop switches

Emergency stop overrides located at control station

Hydraulic reservoir capacity of 66 gal

Serviceability

Bearings on the boom and retract cables can be greased through access holes in the boom side plates.

Removable winch allows the internal telescoping cylinder to be removed quickly, without dismantling the boom

Internal anti-two-block wire routing eliminates external reel and wire to protect crane components

The boom sheave case is open, allowing access to replace the internal anti-two-block wire and to observe internal boom components

Internal boom parts have been reduced, decreasing service time when rebuilding the machine

* Product may be shown with optional equipment.

4Contents

Features 2

Mounting configurations 5

Specifications 6

Capacities 8

Dimensions 16

Accessories 17

CWT

4763 kg (10,500 lb)

4166 mm (164")MIN

3493 kg (7700 lb) MIN4082 (9000 lb) MAX

ASH1727 mm (68")MIN

180 cm (11 in)

328 cm (20 in)

123 cm (7.5 in)

33 cm (2in)

SFO

5Series 600E2

Mounting configurations

Configuration 1 with Torsion Box 180 Full Capacity Work AreaWorking area .................................................................................................... 180Gross Axle Weight Rating Front .............................................. 6350 kg (14,000 lb)Gross Axle Weight Rating Rear............................................. 15 442 kg (34,000 lb)Gross Vehicle Weight Rating ................................................ 21 773 kg (48,000 lb)Wheelbase ...................................................................................... 589 cm (232 in)Cab to Axle/trunnion (CA/CT) ..................................................... 417 cm (164 in)

Frame Section Modulus (SM) under crane: (758 MPa 110,000 PSI) .......................................................... 261 cm3 (15.9 in3)

Frame Section Modulus (SM) over rear stabilizers: (758 MPa 110,000 PSI) ............................................................ 213 cm3 (13 in3)Stability Weight, Front ............................................. 3629 kg (8000 lb) minimum*Stability Weight, Rear ............................................ 4763 kg (10,500 lb) minimum*Estimated Average Final Weight ........................................... 13 608 kg (30,000 lb)

Configuration 2 with Torsion Box 360 Full Capacity Work AreaWorking area ......................................................................................................360Gross Axle Weight Rating Front ............................................... 6350 kg (14,000 lb)Gross Axle Weight Rating Rear.............................................. 15 442 kg (34,000 lb)Gross Vehicle Weight Rating ................................................. 21 773 kg (48,000 lb)Wheelbase ....................................................................................... 589 cm (232 in)Cab to Axle/trunnion (CA/CT) ...................................................... 417 cm (164 in)

Frame Section Modulus (SM) under crane: (758 MPa 110,000 PSI) .............................................................. 328 cm3 (20 in3)

Frame Section Modulus (SM) over rear stabilizers: (758 MPa 110,000 PSI) ................................................................213 cm3 (13 in3)Stability Weight, Front .............................................. 3130 kg (7700 lb) minimum*Stability Weight, Rear ............................................. 3175 kg (10,500 lb) minimum*Estimated Average Final Weight ............................................ 13 879 kg (30,600 lb)

Configuration 3 with Torsion Box Rear MountWorking area .................................................................................................... 360Gross Axle Weight Rating Front .............................................. 5443 kg (12,000 lb)Gross Axle Weight Rating Rear............................................. 15 442 kg (34,000 lb)Gross Vehicle Weight Rating ................................................ 20 865 kg (46,000 lb)Wheelbase ..................................................................................... 564 cm (222 in)Cab to Axle/trunnion (CA/CT) .................................................... 396 cm (156 in)

Frame Section Modulus (SM) under crane: (758 MPa 110,000 PSI) ........................................................ 261 cm3 (15.9 in3)

Frame Section Modulus (SM) over rear stabilizers: (758 MPa 110,000 PSI) ..........................................................213 cm3 (15.9 in3)Stability Weight, Front ............................................ 3629 kg (6500 lb) minimum*Stability Weight, Rear .............................................. 4763 kg (9500 lb) minimum*Estimated Average Final Weight ........................................... 13 040 kg (28,750 lb)

Notes: Gross Vehicle Weight rating (GVWR) is dependent on all

components of the vehicle (axles, tires, springs, frame, etc.) meeting manufacturers recommendations: always specify GVWR when purchasing trucks

Diesel engines require a variable speed governor and energize-to-run fuel solenoid for smooth crane operation; electronic fuel injection requires EET engine remote throttle

All mounting data is based on a National Series 600E2 with an 85% stability factor

The complete unit must be installed in accordance with factory requirements, and a test performed to determine actual stability and counterweight requirements per SAE J765; contact the factory for details

Transmission neutral safety interlock switch is required with optional remote control

The configurations are based on the Series 600E2 with an 85% stability factor. The complete unit must be installed in accordance with factory requirements and a test performed to determine actual stability and counterweight requirements since individual truck chassis vary.

Requires front SFO stabilizer to give machine full capacity 360 around the truck. Truck must meet the minimum requirements above. Front stabilizer gives the machine a solid base, helping the operator control loads precisely. Extended front frame rails required for SFO installation.

Allows the installation of the Model 600E2 on a chassis. In most cases, the chassis will not require reinforcing, and the amount of counterweight required is minimized, increasing payload capacities. Extended front frame rails required for SFO installation.

1727 mm(68") MIN

4166 mm(164") MIN

4763 kg(10,500 lb)

CWT

ASH

3629 kg (8000 lb) MIN4264 kg (9400 lb) MAX

1956 mm(77") MIN

SRO

3692 mm(156") MIN

1676 mm(66") MIN

2948 kg(6500 lb) MIN

CWT

4309 kg(9500 lb) MIN

*Estimated axle scale rates prior to installation of crane, stabilizers and subbase for 85% stability.

6Specifications

Boom and jib combinations data

Note: Maximum tip is measured with outriggers/stabilizers fully extended.

Available in six basic models:

Model 638E2 Equipped with a 4,88 m - 11,58 m (16 ft - 38 ft) three-section boom. Maximum tip height is 14,63 m (48 ft) (no jib option available).4,88 m - 11,58 m (16 ft - 38 ft) three-section boom

Model 649E2 Equipped with a 4,88 m - 15 m (16 ft - 49 ft) four-section boom. Maximum tip height is 17,98 m (59 ft).4,88 m - 15 m (16 ft - 49 ft) four-section boom (no jib option available).

Model 680E2 Equipped with a 7,32 m - 24,38 m (24 ft - 80 ft) four-section boom. Maximum tip height is 27,44 m (90 ft) (no jib option available).7,32 m - 24, 38 m (24 ft - 80 ft) four-section boom

Model 690E2 Equipped with a 8,23 m - 27,43 m (27 ft - 90 ft) four-section boom. This model can be equipped with a 7,62 m - 13,72 m (25 ft - 45 ft) two section jib. Maximum tip height with 13,72 m (45 ft) jib is 43,95 m (144 ft).8,23 m - 27,43 m (27 ft - 90 ft) four-section boom 6FJ45M 7,62 m - 13,72 m (25 ft - 45 ft) two-section jib

Model 671E2 Equipped with a 8,23 m - 21,64 m (27 ft - 71 ft) three-section boom. This model can be equipped with a 7,62 m - 13,72 m (25 ft - 45 ft) two-section jib. Maximum tip height with 13,72 m (45 ft) jib is 38,25 m (125 ft).8,23 m - 21,64 m (27 ft - 71 ft) three-section boom 6FJ45M 7,62 m - 13,72 m (25 ft - 45 ft) two-section jib

Model 660E2 Equipped with a 7,12 m - 18,3 m (24 ft - 60 ft) three-section boom. Maximum tip height is 21,3 m (70 ft) (no jib option available).7,2 m - 18,3 m (24 ft - 60 ft) three-section boom

7Series 600E2

Specifications

600E2 winch data

WinchCable

suppliedAverage breaking strength

Max pull Max pull Max pull Max pull Max pull Max pull

Standard planetary

winch

9/16 in diameter rotation resistant

17 463 kg (38,500 lb)

3492,66 kg (7700 lb)

6985,32 kg (15,400 lb)

10 477,98 kg (23,100 lb)

13 970,65 kg (30,800 lb)

14 514,96 kg (38,500 lb)

14 514,96 kg (40,000 lb)

Winch Bare drum pull Allowable cable pull

With standard rotation resistant rope 4627 kg (10,2000 lb) 3493 kg (7700 lb)

Loadline deduct

Block type Rating Weight

Downhaul weight 3,49 t (3.85 USt) 68 kg (150 lb)

1-sheave block 10,48 t (11.55 USt) 91 kg (200 lb)

2-sheave block 17,46 t (19.25 USt) 161 kg (355 lb)

1 part line 2 part line 3 part line 4 part line 5 part line 6 part line All winch pulls and speeds are shown

on the fourth layer.

Winch line pulls would increase on the first and second layers.

Winch line pulls may be limited by the winch capacity or the ANSI 5 to 1 cable safety factor, shown below this chart.

Hook blocks are rated at maximum capacity for the block. Do not exceed rated cable pull with any block.

Layer

Winch pull Winch speed BOS winch speed Rope capacity

kg lb mpm fpm mpm fpm m ft

1 4708 10,380 48 157 68 222 19 64

2 4246 9360 53 175 75 246 41 136

3 3865 8520 59 192 83 271 65 215

4 3547 7820 64 209 90 294 91 301

5 3279 7230 69 257 97 318 120 394

Note: All ratings based on 128,7 LPM at 22,75 MPa (34 GPM at 3300 psi) Burst of Speed maximum bull = 1361 kg (3000 lb)

8THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.

The individual cranes load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

Capacities

Series 638E2: 11,58 m (38 ft) boom

Load chart

CAUTION: Do not operate crane booms, jib extensions, any

accessories or loads within 3 m (10 ft) of live power lines or other conductors of electricity.

Jib and boom capacities shown are maximum for each section.

Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum

allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck.

Always level the crane with the level indicator located on the crane.

The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads.

Overloading this crane may cause structural collapse or instability.

Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities.

Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending

boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine.

National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer.

0 20 400

40

60

RADIUS IN FEET

HEIGHT IN FEET

38

31

24

16

BOOM LEN

GTH

IN FEET

8070

6050

40

30

20

0

-10A B

10 20

16 ftBOOM(lb)

LOADEDBOOMANGLE(deg)

A24 ftBOOM(lb)


B31 ft

BOOM(lb)


38 ftBOOM(lb)


LOADEDRADIUS

(ft)

568101214161820253035

40,00036,15030,25025,60021,90016,750

10,850

28,55024,30020,90018,15016,20014,20012,200

7050

27,50023,45020,15017,80015,80014,15012,90010,150

5100

25,75022,20019,20017,05015,20013,75012,5009950835062003850

67 6355.545.5 34 15

0

6862.556.5 50 4334.526.5

0

74 69 6560.5 5651.5 4731.5

0

77 7370.566.564.559.5 57 4635.518.50

NOTE:1. All capacities are in pounds, angles in degrees, radius in feet.2. Loaded boom angles are given as reference only.3. Shaded areas are structurally limited capacities.

9Series 600E2

Capacities

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual cranes load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

Series 649E2: 15 m (49 ft) boom

Load chart

0 20 40 600

20

40

60

80

RADIUS IN FEET

HEIGHT IN FEET

49

41

33

25

16

BOOM LEN

GTH

IN FEET

-10

8070

60

50

40

30

20

10

0A B C

16 ftBOOM(lb)


A25 ft

BOOM(lb)


B33 ft

BOOM(lb)


C41 ft

BOOM(lb)


49 ftBOOM(lb)


LOADEDRADIUS

(ft)

5810121416202530354045

40,00029,60024,70020,40013,750

10,950

38,10027,40023,20020,20017,75015,75012,100

6350

26,20022,20019,25017,00015,20012,50098506950

4350

25,30021,30018,45016,30014,55012,050980080506450

3200

19,50017,50015,00013,75011,75096008050680056504300

2600

67 54 4431.58.5

0

76.0 68 6357.551.5

45.0 29

0

7470.566.562.558.549.5 36.016.5

0

77.574.571.568.565.5 59.0 50 4027.5

0

77.5 75.572.5 70 65.0 58.050.5 43.0 33.518.5

0




Jib and boom capacities shown are maximum for each section.

Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum









10

Capacities



Load chart

CAUTION: Do not operate crane booms, jib extensions, any accessories

or loads within 3 m (10 ft) of live power lines or other conductors of electricity.

Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum









24 ftBOOM(lb)


A33 ft

BOOM(lb)


B42 ftBOOM(lb)


C51 ft

BOOM(lb)


60 ftBOOM(lb)


LOADEDRADIUS(ft)

58101214162025303540455055

40,00027,20022,80019,65017,15015,15011,150

6150

25,80021,60018,70016,40014,60011,95094006600

3950

25,00020,70017,80015,75014,05011,550935077006100

2700

20,40017,40015,25013,60011,20091007600640053504250

1950

17,15014,95013,20010,85088007400620054004550390030001300

75.567.5 62 5649.5 4324.5

0

74 70 6762.558.549.537.5 18

0

77.5 75 72 69 66 6051.5 4230.5

0

7875.5 73 71 6659.5 5345.536.5 25

0

78.576.574.570.565.5 6054.5 48 41 3321.50

0

20

40

60

80

100

0 20 40 60 80RADIUS IN FEET

HEIGHT IN FEET

BOOM LEN

GTH

IN FEET

-10

8070

60

50

40

30

20

10

0

51

42

60

24

33

A B C


11Series 600E2

Capacities


28 ftBOOM(lb)


A35 ft

BOOM(lb)


B44 ftBOOM(lb)


C53 ft

BOOM(lb)


D62 ftBOOM(lb)


71 ftBOOM(lb)


LOADEDRADIUS

(ft)

581012141620253035404550556065

7770.565.5 61 5650.5 3815.5

0

7571.5

6864.560.552.540.5 26

0

78.5 76 7370.567.561.553.545.5 35 20

0

7976.574.5 72 67 61 5548.040.029.514.0

0

79 77 75 71 66 6155.549.5 43 3525.55.5

0

77.5 7469.565.5 61 56 5145.5 3931.5 220

40,00026,15021,60018,50016,60014,90011,9008250

4800

25,20021,45018,40016,00014,20011,60094007100

3600

24,60020,80017,80015,85014,00011,3509100750062004500

2250

20,40017,45015,30013,55011,000880073006150520043502800

1500

16,80014,65013,00010,60085507100600051004350370030001800

950

12,65010,300830068505950505044003800325027502150550


Load chart











0

20

40

60

80

100

0 20 40 60 80RADIUS IN FEET

HEIGHT IN FEET53

44

35

62

71

BOOM LEN

GTH

IN FEET

-10

8070

60

50

40

30

20

10

0

28

A B C D



12

Capacities


28 ftBOOM(lb)


A35 ft

BOOM(lb)


B44 ftBOOM(lb)


C53 ft

BOOM(lb)


D62 ftBOOM(lb)



25 ftJIB(lb)


45 ftJIB(lb)

71 ftBOOM(lb)


LOADEDRADIUS

(ft)

581012141620253035404550556065707580859095

7770.565.5 61 5650.5 3819.5

0

7571.5

6864.560.552.540.5 26

0

78.5 76 7370.567.561.553.545.5 35 20

0

7976.574.5 72 67 61 5548.040.029.514.0

0

79 77 75 71 66 6155.549.5 43 3525.5 10

0

7977.5 7469.565.5 61 56 5145.5 3931.5 22

40,00025,55021,00017,90016,00014,30011,3007650

4200

24,75021,00017,95015,55013,70011,10089006600

3100

24,25020,45017,45015,50013,65010,9508700710058004100

1850

20,10017,15015,00013,25010,700850070005850490040502450

1150

16,55014,40012,75010,35083006850575048504050340027001500

650

12,45012,45010,050805066005700480041503550300025001900

4400390032002750235020001750150013001100900700600

2600245023002100190017001500135012001050900800700600

75.572.5

69 6662.559.555.5 52 4843.5 3933.527.5

76.5 74 72 6966.5 64 6158.5 55 5248.5 45 4136.5

Series 671E2: 21,64 m (71 ft) boom with 13,72 m (45 ft) jib

Load chart

CAUTION: Do not operate crane booms, jib extensions, any accessories or

loads within 3 m (10 ft) of live power lines or other conductors of electricity.



Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind,

ground conditions, operating speeds and their effects on freely suspended loads.

Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must

be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom

or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine.Note:

1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius.2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths.

0

20

40

60

80

100

120

140

0 20 40 60 80 100 120

RADIUS IN FEET

HEIGHT IN FEE

T

53

44

35

62

71

-10

1st Jib 25'

2nd Jib 45'

BOOM LEN

GTH

IN FEE

T

60

8070

50

4036.5

28 Do notextendjib intothisarea

27.5

20

10

0

30

A B C D



13Series 600E2

Capacities



Load chart







Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must

be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending


24 ftBOOM(lb)


A36 ftBOOM(lb)


B47 ft

BOOM(lb)


C58 ftBOOM(lb)


D69 ftBOOM(lb)


80 ftBOOM(lb)


LOADEDRADIUS(ft)

5810121416202530354045505560657075

76 6862.556.550.543.5 27

0

75 7268.5 65 6153.5 4329.5

0

76.5 7471.5

7063.555.5 48 39 287.5

0

77.575.573.569.5 6458.5 52 45 37 2813.5

0

7773.5

6964.559.554.5 49 43 36 28 16

77 73 69 65 6156.5 52 4741.535.528.518.5

40,00027,10022,40019,50017,10014,75011,100

5800

25,40021,40018,35016,00014,20011,45091507000

3050

20,60017,55015,30013,55011,00090007200585046502600

1750

17,05014,75013,05010,5508450705059004800410034502200

1000

12,15010,100820068505700485041503500295024501550

855080006550550046504000345030002550215017001150


0

20

40

60

80

100

120

0 20 40 60 80 100

RADIUS IN FEET

HEIGHT IN FEET

36

58

69

80

24

47

BOOM LEN

GTH

IN FEET

-10

8070

60

50

40

30

20

10

0A B C D


14

Capacities



Load chart

CAUTION: Do not operate crane booms, jib extensions, any accessories

or loads within 3 m (10 ft) of live power lines or other conductors of electricity.










0

20

40

60

80

100

120

0 20 40 60 80 100

RADIUS IN FEET

HEIGHT IN FEET

-10

54

78

90

41

66

BOOM LEN

GTH

IN FEET

8070

60

50

40

30

20

10

0

27

DCBA

27 ftBOOM(lb)


A41 ft

BOOM(lb)


B54 ftBOOM(lb)


C66 ftBOOM(lb)


D78 ft

BOOM(lb)


90 ftBOOM(lb)


LOADEDRADIUS

(ft)

581012141620253035404550556065707580

77 70 6661.5 57 51 40 19

0

74 71 6865.558.5 50 4026.5

0

76 7471.567.561.5 55 48 40 3216.5

0

77.575.5 72 6762.5 58 5246.539.5 3121.5

7671.5

6863.559.554.5 5044.539.532.5 24 11

77.574.571.5

6864.5 61 5753.048.5 44 39 3326.5

40,00025,75021,40018,45016,40014,75011,2507500

4150

20,95017,75015,25013,30010,800905075505250

1950

17,00015,00013,20010,500815067505700460038502450

850

14,45012,600995079006450545045503850315025501800

97007750625052004400370031502650225017501250450

785075506150505042003550300025502150185015001150800


Series 600E2

Capacities

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual cranes load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 15

Series 690E2: 27,43 m (90 ft) boom with 13,72 m (45 ft) jib

Load chart



Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable

loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck.

Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind,

ground conditions, operating speeds and their effects on freely suspended loads.

Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be

deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or

winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine.

Note:1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius.2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths.


27 ftBOOM(lb)


A41 ft

BOOM(lb)


B54 ftBOOM(lb)


C66 ftBOOM(lb)


D78 ft

BOOM(lb)



25 ftJIB(lb)


45 ftJIB(lb)

90 ftBOOM(lb)


LOADEDRADIUS

(ft)

581012141620253035404550556065707580

77 70 6661.5 57 51 40 19

0

74 71 6865.558.5 50 4026.5

0

76 7471.567.561.5 55 48 40 3216.5

0

77.575.5 72 6762.5 58 5246.539.5 3121.5

7671.5

6863.559.554.5 5044.539.532.5 24

77.574.571.5

6864.5 61 57 5348.5 44 39 3326.5

40,00025,20020,80017,85015,80014,15010,6506900

3550

20,55017,35014,85012,90010,400865071504850

1550

16,70014,70012,90010,200785064505400430035502150

550

14,25012,350970076506200520043003600290023001550

95007550605050004200350029502450205015501050

77007400600048504000335028002350195016501300950600

28002500220019001600140012001000800700600500

17001500130011001000900800700600500

7875.5 73 7067.565.562.559.556.553.5 50 47

78.576.5 74 72 7067.565.5 6360.5 58

0

20

40

60

80

100

120

140

160

0 20 40 60 80 100 120

RADIUS IN FEET

HEIGHT IN FEE

T

27

1st Jib 25'

2nd Jib 45'

80

70

6057.5

BOOM LEN

GTH

IN FEE

T

54

78

90

41

66Do notextendjib intothisarea

5046.5

40

30

20

10

0-10 DCBA


143 (5.62) TYP35.05 x 50.80(1.38 x 2.00)Full R TYP 8X Slot

38 (1.50) TYP

1070 (42.13)

73 (2.88) TYP1073

(42.25)

Scale: 1/12

Maintain clearance for R1144 (R45.00) Tailswing

Ground penetration 278 (11.00)

1256 (49.50)

278 (11.00)

461 (18.00)

Frame height978 (38.50)

3086 (121.50)

667 (26.25)

Ground Level

1019 (40.00) 1218 (48.00)

1076 (42.50) 1275 (50.25)

406 (16.00) 338 (13.25) 548 (21.50)

292 (11.50)

959 (37.75)

9.95

1777 (70.00) 2156 (85.00)

2343 (92.25)

1833 (72.00)

2387 (94.00)

3000 (118.125)

1132 (44.50)

533 (21.00) 3518 (138.50)

80.00

G

16

Dimensions

Subbase C.G. are located from center of rotation

Subbase Weight C.G. length

Standard 18 ft 1229 kg (2710 lb) 2,87 m (113 ft)



Dimensions are in mm (in) unless otherwise specified.

Series Retracted length

Extended length

Subbase G (wet) Dry/Wt With oil/wt

638E2 5,1 m(16 ft 7 in)

11,7 m(38 ft 3 in)

5,5 m (18 ft)

1,23 m (48.3 in)

6192 kg (13,651 lb)

6462 kg (14,246 lb)

649E2 4,9 m(16 ft)

14,9 m(49 ft)

5,5 m(18 ft)

1,28 m (50.7 in)

6481 kg (14,289 lb)

6751 kg (14,884 lb)

660E2 7,3 m(24 ft)

18,3 m(60 ft)

5,5 m(18 ft)

1,52 m (59.9 in)

6748kg (14,876 lb)

7018 kg (15,471 lb)

671E2 8,4 m (27 ft 7 in)

21,6 m(71 ft)

6,1 m( 20 ft)

1,90 m (74.7 in)

7181 kg (15,831 lb)

7451 kg (16,426 lb)

680E2 7,3 m(24 ft)

24,4 m(80 ft)

5,5 m(18 ft)

1,71 m (67.5 in)

7256 kg (15,996 lb)

7526 kg (16,591 lb)

690E2 8,5 m(27 ft 10 in)

27,4 m(90 ft)

6,1 m(20 ft)

1,98 m (78.1 in)

7700 kg (16,976 lb)

7970 kg (17,571 lb)

Weight includes all items except Ash 363 kg (830 lb) and bed.

38' boom: 16 8.5" Retracted/38' Extended (5,1 m - 11,6 m) 49' boom: 16' Retracted/49' Extended (4,88 m - 15 m)60' boom: 24' Retracted/60' Extended (7,2 m - 18,3 m)

71' boom: 27' 7" Retracted/71' Extended (8,41 m - 21,64 m)80' boom: 24' Retracted/80' Extended (7,3 m - 24,4 m)

90' boom: 27' 10" Retracted/90' Extended (8,48 m - 27,43 m)


17Series 600E2

Accessories

Radio Remote Controls Eliminate the handling and maintenance concerns that accompany RB4Rcabled remotes. Operate to a range of about 76 m (250 ft), varying with conditions.

Heavy-duty Personnel Basket 1200 lb (544 kg) capacity steel basket with safety loops for two passengers. Gravity leveling 183 cm x 107 cm (72 in x 42 in) platform. Fast attachment and BSA-1secure locking systems. Load chart must show 1043 kg (2300 lb) minimum to BSA-R1 (provides rotation)operate this accessory.

Duty Cycle Package Burst-of-Speed winch control option, with dual stand upcontrol and hydraulic oil cooler, self-contained radiator DCPKGsystem with electric fan. Continuous Rotation Allows rotation of turret/boom without rotation stop. CR

Single Front Outrigger Center mount front stabilizer for 360 stability with a 25 in vertical stroke. SFO

Bulkhead Options Steel 30 in solid wall bulkhead BHSD

Spanish-Language Danger Decals, SDD Control Knobs, and Operators Manuals SOM

18

Notes

19Series 600E2

Notes

2014 ManitowocForm No.600E2 PGPart No.600E2 /0414 / PDF www.manitowoccranes.com

This document is non-contractual. Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment.

Regional offices

ChinaShanghai, China Tel: +86 21 6457 0066Fax: +86 21 6457 4955

Greater Asia-Pacific Singapore Tel: +65 6264 1188 Fax: +65 6862 4040

Europe, Middle East, Africa Dardilly, France Tel: +33 (0)4 72 18 20 20 Fax: +33 (0)4 72 18 20 00

Americas Manitowoc, Wisconsin, USA Tel: +1 920 684 6621 Fax: +1 920 683 6277

Shady Grove, Pennsylvania, USA Tel: +1 717 597 8121 Fax: +1 717 597 4062

Regional headquarters

Manitowoc Cranes

ChinaBeijingChengduGuangzhouXian

Greater Asia-PacificAustraliaBrisbaneMelbourneSydneyIndiaChennaiDelhiHyderabadPuneKoreaSeoulPhilippinesMakati CitySingapore

FactoriesBrazilPasso FundoChinaTaiAnZhangjiagangFranceCharlieuMoulinsGermanyWilhelmshavenIndiaPuneItalyNiella TanaroPortugalBaltarFnzeresUSAManitowoc Port WashingtonShady Grove

AmericasBrazilAlphavilleMexicoMonterreyChileSantiago

Europe, Middle East, AfricaFranceBaudemontCergyDecinesGermanyLangenfeldItalyLainateNetherlandsBredaPolandWarsawPortugalBaltarRussiaMoscowSouth AfricaJohannesburgU.A.E.DubaiU.K.Buckingham

600E2 Product Guide Imperial

Documents

Transcript of 600E2 Product Guide Imperial