405010-3.x ds iwap107 wireless access point enclosure data sheet
3
A 405010-3.2 The iWAP107 is an ATEX and IECEx approved Zone 1 Access Point Enclosure with intrinsically safe RF outputs which is designed to allow the deployment of wireless networks in hazardous areas. The concept allows installation of equipment from leading WLAN vendors such as Cisco, Aruba, Aeroscout and Motorola. Each type of Access Point or RF transmitting device is rigorously checked and tested by Extronics to ensure conformity to the latest standards. This means that the user may select the vendor of their choice when extending a WLAN to hazardous areas. However equipment not previously approved will require assessment to determine its suitability. The galvanically isolated RF outputs of the iWAP107 allows users to choose non-certified antennas for use with their wireless hardware e.g. Extronics iANT2xx range of high quality rugged outdoor antennas. Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas. Up to eight antennas can be utilized, allowing the MIMO functionality of the latest 802.11n/ac compatible wireless access points to be implemented, providing optimum coverage and maximum data throughput on Chemical Plants, Oil Refineries or Oil & Gas Platforms. Optional features include surge arrestors for lightning suppression in outdoor installations and single mode or multimode fibre optic inputs to allow for extended Ethernet link distance. Overview Features and Benefits iWAP107 Universal Zone 1 Access Point Enclosure Specification Certification Type II 2 (1)GD Ex d [ia IIC Ga] IIB+H 2 T5 Gb II 2 (1)GD Ex tb [ia Da] IIIC T100°C Db Power Supply 120VAC or 230VAC (+/- 10%) / IEEE802.3at PoE Maximum Power Consumption Basic configuration: 25W With heaters: 125W Enclosure Material Marine grade copper free aluminium light alloy, epoxy powder coated or 316L Stainless Steel (optional) Ingress Protection IP66 Weight Aluminium—Approx 30kg (hardware dependant) 316L Stainless Steel—Approx 70kg (hardware dependant) Dimensions Aluminium— 415 x 315 x 250 mm (w x h x d) 316L Stainless Steel— 415 x 315 x 253 mm (w x h x d) Environmental Ambient temperature: -20ºC to +60ºC (dependant on wireless hardware—see individual AP operating temperatures overleaf) Relative humidity; 0 to 95%, non condensing Input Connections - AC / DC power input screw terminals - 10/100/1000Base-T Ethernet on RJ45 socket - Single or Multi mode fibre input on LC connector & Splice Tray (all via M20x1.5-6H drilled entries) Ethernet Link distance 10/100/1000BASE-T Ethernet on CAT5e: up to 100m 100BASE-FX Multi Mode fibre : up to 2km, wavelength 1310nm 100BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm 1000BASE-LX Multi Mode fibre : up to 550m, wavelength 1310nm 1000BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm Output Connection Up to eight galvanically isolated N-Type RF outputs Internal RF Losses (typical) 2.4GHz 5.0Ghz 2.4 / 5GHz Dual Band Without Surge Arrestor: 2.7dB 3.6dB 3.2dB / 4.5dB With Surge Arrestor: 2.8dB 3.9dB 3.3dB / 4.8dB Certification ATEX: TRAC14ATEX0022X IECEx: TRC 14.0010X NEC 500 - C1 D1: Pending Galvanically Isolated RF Outputs Non-certified antennas can be used with chosen wireless hardware* Extended Temperatures Operating temperature range of -20°C to +60°C for the most extreme environments. Future Proof Infrastructure As new hardware becomes available it can be assessed by Extronics for compliance to the certification. The existing hardware can then be replaced with the new version meaning the user is installing a future proof solution. Gigabit Ethernet Supports 100/1000Base-T/FX/LX options to offer a significant increase in speed over the older fast Ethernet standard. MIMO Radio Offers increased data throughput and higher immunity to signal interference for optimal performance in challenging industrial environments. Copyright © Extronics Ltd 2014. The information contained in this document is subject to change without notice. Extronics cannot be held responsible for any errors or inaccuracies within this document. *Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas. Zone 1 Explosion Proof Wireless Access Point enclosure system with intrinsically safe RF outputs. II 2(1) GD Ex d [ia IIC Ga] IIB+H 2 T5 Gb Ex tb [ia Da] IIIC T100°C Db Extronics Ltd., 1 Dalton Way, Midpoint 18, Middlewich, Cheshire, UK. CW10 0HU Tel: +44 (0) 845 277 5000 Fax: +44 (0)845 277 4000 E-mail: [email protected] Web: www.extronics.com
-
Upload
chris-easy -
Category
Documents
-
view
60 -
download
4
Transcript of 405010-3.x ds iwap107 wireless access point enclosure data sheet
A
405010-3.2
The iWAP107 is an ATEX and IECEx approved Zone 1 Access Point Enclosure with intrinsically safe RF outputs which is designed to allow the deployment of wireless networks in hazardous areas. The concept allows installation of equipment from leading WLAN vendors such as Cisco, Aruba, Aeroscout and Motorola. Each type of Access Point or RF transmitting device is rigorously checked and tested by Extronics to ensure conformity to the latest standards. This means that the user may select the vendor of their choice when extending a WLAN to hazardous areas. However equipment not previously approved will require assessment to determine its suitability.
The galvanically isolated RF outputs of the iWAP107 allows users to choose non-certified antennas for use with their wireless hardware e.g. Extronics iANT2xx range of high quality rugged outdoor antennas. Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas. Up to eight antennas can be utilized, allowing the MIMO functionality of the latest 802.11n/ac compatible wireless access points to be implemented, providing optimum coverage and maximum data throughput on Chemical Plants, Oil Refineries or Oil & Gas Platforms. Optional features include surge arrestors for lightning suppression in outdoor installations and single mode or multimode fibre optic inputs to allow for extended Ethernet link distance.
Overview
Features and Benefits
iWAP107 Universal Zone 1 Access Point Enclosure
Specification Certification Type II 2 (1)GD Ex d [ia IIC Ga] IIB+H2 T5 Gb
II 2 (1)GD Ex tb [ia Da] IIIC T100°C Db
Power Supply 120VAC or 230VAC (+/- 10%) / IEEE802.3at PoE
Maximum Power Consumption
Basic configuration: 25W With heaters: 125W
Enclosure Material Marine grade copper free aluminium light alloy, epoxy powder coated or 316L Stainless Steel (optional)
Ingress Protection IP66
Weight Aluminium—Approx 30kg (hardware dependant) 316L Stainless Steel—Approx 70kg (hardware dependant)
Dimensions Aluminium— 415 x 315 x 250 mm (w x h x d) 316L Stainless Steel— 415 x 315 x 253 mm (w x h x d)
Environmental Ambient temperature: -20ºC to +60ºC (dependant on wireless hardware—see individual AP operating temperatures overleaf) Relative humidity; 0 to 95%, non condensing
Input Connections - AC / DC power input screw terminals - 10/100/1000Base-T Ethernet on RJ45 socket - Single or Multi mode fibre input on LC connector & Splice Tray (all via M20x1.5-6H drilled entries)
Ethernet Link distance
10/100/1000BASE-T Ethernet on CAT5e: up to 100m 100BASE-FX Multi Mode fibre : up to 2km, wavelength 1310nm 100BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm 1000BASE-LX Multi Mode fibre : up to 550m, wavelength 1310nm 1000BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm
Output Connection Up to eight galvanically isolated N-Type RF outputs
Internal RF Losses (typical)
2.4GHz 5.0Ghz 2.4 / 5GHz Dual Band Without Surge Arrestor: 2.7dB 3.6dB 3.2dB / 4.5dB With Surge Arrestor: 2.8dB 3.9dB 3.3dB / 4.8dB
Certification ATEX: TRAC14ATEX0022X IECEx: TRC 14.0010X NEC 500 - C1 D1: Pending
Galvanically Isolated RF Outputs Non-certified antennas can be used with chosen wireless hardware*
Extended Temperatures Operating temperature range of -20°C to +60°C for the most extreme environments.
Future Proof Infrastructure As new hardware becomes available it can be assessed by Extronics for compliance to the certification. The existing hardware can then be replaced with the new version meaning the user is installing a future proof solution.
Gigabit Ethernet Supports 100/1000Base-T/FX/LX options to offer a significant increase in speed over the older fast Ethernet standard.
MIMO Radio Offers increased data throughput and higher immunity to signal interference for optimal performance in challenging industrial environments.
Copyright © Extronics Ltd 2014. The information contained in this document is subject to change without notice. Extronics cannot be held responsible for any errors or inaccuracies within this document.
*Any antennas not listed in the Extronicsrange must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas.
Zone 1 Explosion Proof Wireless Access Point enclosure system with intrinsically safe RF outputs.
II 2(1) GD
Ex d [ia IIC Ga] IIB+H2 T5 Gb
Ex tb [ia Da] IIIC T100°C Db
Extronics Ltd., 1 Dalton Way, Midpoint 18, Middlewich, Cheshire, UK. CW10 0HU
Tel: +44 (0) 845 277 5000 Fax: +44 (0)845 277 4000 E-mail: [email protected] Web: www.extronics.com
Antenna Locations In order that customers enjoy the best possible wireless performance from their iWAP107 system we recommend that, where possible, antennas are remotely mounted as high as possible and with sufficient separation. It is recognised that in some instances remote mounting of antennas is not a feasible option and for these circumstances we have optimised the antenna positions for the various configurations. When completing the order information for option [#10] overleaf, you must specify remote or direct mounted antennas. The RF connections will then be supplied as shown in the diagrams below depending on the total number of RF ports selected for your device.
Remote Mount - Up to 6 antennas plus Data & Power outlets
Direct Mount - 2 antennas plus Data & Power outlets
Direct Mount - 3 antennas plus Data & Power outlets
Direct Mount - 4 antennas plus Data & Power outlets
Direct Mount - 6 antennas (3 bottom & 3 top) plus Data & Power outlets
Extronics Ltd., 1 Dalton Way, Midpoint 18, Middlewich, Cheshire, UK. CW10 0HU
Tel: +44 (0) 845 277 5000 Fax: +44 (0)845 277 4000 E-mail: [email protected] Web: www.extronics.com
iWAP107 - Universal Access Point Enclosure iWAP107-[#1]-[#2]-[#3]-[#4]-[#5]-[#6]-[#7]-[#8]-[#9]-[#10]-[#11]
Specify option [#1] - Wireless Network Hardware Hardware supplied by customer* C Hardware supplied by Extronics E
*Extronics can supply the wireless hardware, or alternatively you may wish to “free issue” one of the already certified solutions so that we canfactory fit it (see option #2 for certified hardware list). (“Free Issue” means to supply and deliver to Extronics HQ at your own cost.)
Specify option [#2] - Type Of Wireless Network Hardware (Max operating temperature listed in brackets only applies to PoE powered units, take lower value if powered by AC/DC. If the heater option is selected this will allow all AP’s to operate at a lower ambient temperature of –20oC.)
Aruba AP-134 Access Point (0oC to 40/45oC) 29 Configuration for AeroScout Location Receiver (0°C to 45/50°C) 31 Cisco AP3500 Series Access Point (-20oC to 45/50oC) 33 Cisco AP1260 Series Access Point (-20oC to 45/50oC) 35 Cisco AP1600 Series Access Point (-20oC to 45/50oC) 36 Cisco AP2600 Series Access Point (-20oC to 45/50oC) 37 Cisco AP3600 Series Access Point (-20oC to 45/50oC) 38 Cisco AP1530 Series Access Point (-20oC to 55/60oC) 39 Aruba AP-110 Series Access Point (0oC to 40/45oC) 40 Aruba AP-220 Series Access Point (0oC to 40/45oC) 41 Lancom IAP-321 (-20oC to 40/45oC) 44 Cisco AP3700 Series Access Point (-20oC to 40/45oC) 45 New Wireless Hardware—Order code to be advised TBA
Specify option [#3] - Power Supply 120VAC Supply AC1 230VAC Supply AC2 IEEE802.3at compliant Power-Over-Ethernet (Chosen hardware must be compatible with PoE supply) POE
Specify option [#4] - Ethernet Connection 100/1000Base-T Ethernet on CAT5e copper C 100/1000Base-T Ethernet on CAT5e copper - surge protected CS Multimode 100BASE-FX fibre with LC connector F Single mode 100BASE-LX10 fibre with LC connector S Multimode 1000BASE-LX fibre with LC connector FG Single mode 1000BASE-LX10 fibre with LC connector SG
Specify option [#5] - Frequency Output for Radio 1 2.4GHz 24 5GHz 50 Dual band output (2.4GHz & 5GHz) 2450
Specify option [#6] - Number of Antenna Outputs for Radio 1 0/1/2/3/4 off N-type connector 0/1/2/3/4 0/1/2/3/4 off N-type connector with surge protector 0S/1S/2S/3S/4S
Specify option [#7] - Frequency Output for Radio 2 Not Required N 2.4GHz 24 5GHz 50 Dual band output (2.4GHz & 5GHz) 2450
Specify option [#8] - Number of Antenna Outputs for Radio 2 0/1/2/3/4 off N-type connector 0/1/2/3/4 0/1/2/3/4 off N-type connector with surge protector 0S/1S/2S/3S/4S
Specify option [#9] - Enclosure Heating (not compatible with POE or DC supplies) No enclosure heating N Supplied with enclosure heating H
Specify option [#10] - Antenna Position (see previous page for antenna layout pattern which relates to total No. of RF outputs) Remote Mount R Direct Mount D
ALSpecify enclosure material [#11] Marine gra de co pper free aluminium light alloy 316L Stainless Steel SS
Accessories 316L Stainless Steel Enclosure Pipe mount bracket kit for iWAP107 Enclosure iWAPMB02 to fit 1.5” - 2” diameter pipe or rectangular post
Extronics Ltd., 1 Dalton Way, Midpoint 18, Middlewich, Cheshire, UK. CW10 0HU
Tel: +44 (0) 845 277 5000 Fax: +44 (0)845 277 4000 E-mail: [email protected] Web: www.extronics.com
