3D INTEGRATION
-
Upload
mohd-shakeel -
Category
Technology
-
view
747 -
download
3
Transcript of 3D INTEGRATION
PRESENTED BY VIPIN KUMAR GAUTAM
09-EC-58
3D IC TECHNOLOGY
INTRODUCTION 3D IC technology assures higher levels of
miniaturization and integration.
It focuses on portraying advances in interconnect technologies and reduction of interconnect delays.
It is a single circuit built by stacking and integrating. Separately-built layers
WHY A 3D IC?In modern world when the utilization of IC’s is increasing rapidly , a problem is being observed by the IC developers and that problem is space.general ICs those are in form of 2-D having a limited space.So developers are now a days planning on a concept that is called 3D IC.In 3D IC developers use 3rd dimension to manufacture the IC.
• Interconnect structures increasingly consume more of the power and delay budgets in modern design.
• Reasonable solution: increase the number of “nearest neighbors” seen by each transistor by using 3D IC design
Design tools for 3D-IC designDemand for EDA tools
As the technology matures, designers will want to exploit this design area No design tool is available till date for commercial
purpose
Current tool-chainsMostly academic
MIT has developed a tool for the academic purpose.
Energy performanceWire length reduction has an impact on the
cycle time and the energy dissipationEnergy dissipation decreases with the
number of layers used in the designFollowing graph is based on a 3D tool
Energy performance• Energy dissipation decreases with increase
in the number of layers used in the design.
Concerns in 3D circuit• Thermal Issues in 3D-circuits• Inductance Effects • Reliability Issues
Thermal Issues in 3D Circuits• Effects dramatically impact interconnect and
device reliability in 2D circuits
• Due to reduction in chip size of a 3D implementation, 3D circuits exhibit a sharp increase in power density
• Analysis of Thermal problems in 3D is necessary to evaluate thermal robustness of different 3D technology and design options.
Heat Flow in 2DHeat generated arises
due to switchingIn 2D circuits we have
only one layer of Si to consider.
Heat Flow in 3D With multi-layer circuits , the upper layers will also generate a significant fraction of the heat. Heat increases linearly with level
increase
Heat DissipationAll active layers will be insulated from each other
by layers of dielectricsWith much lower thermal conductivity than SiTherefore heat dissipation in 3D circuits can
accelerate many failure mechanisms.
Inductance EffectsInterconnect Inductance Effects
Shorter wire lengths help reduce the inductance
Presence of second substrate close to global wires might help lower inductance by providing shorter return paths.
Reliability Issues?Electro thermal and Thermo-mechanical effects
between various active layers can influence electro-migration and chip performance
Die yield issues may arise due to mismatches between die yields of different layers, which affect net yield of 3D chips.
ADVANTAGES 3D ICs offer many significant benefits,
including:
SPEEDDESIGNHETEREOGENEOUS INTEGRATIONBANDWIDTH
Challenges Yield – Each extra manufacturing step
adds a risk for defects. In order for 3D ICs to be commercially viable, defects must be avoided or repaired.
Heat – Thermal buildup within the stack must be prevented or dissipated
Design complexity – Taking full advantage of 3D requires elegant multi-level designs. Chip designers will need new CAD tools to address the 3D integration
WAFER LEVEL 3D INTEGRATION: An emerging architecture for future chips
APPLICATIONSREAD-ONLY MEMORYDIGITAL CAMERASDIGITAL AUDIO PLAYERSSMART CELLULAR PHONESGAMING DEVICES MEMORY CARDS
Three Dimensional Read-Only Memory ( 3D - ROM).
3D -ROM is a new non-volatile semiconductor memory with lower cost , higher capacity and comparable bandwidth.
It is compatible with standard CMOS process.
More importantly, 3D-ROM can be readily integrated with RAM/flash ROM.
3D Integration of Next-Generation Transceiversfor Wireless Communications:
Conclusion3D IC design is a relief to interconnect driven IC
design.
Still many manufacturing and technological difficulties.
Needs strong applications for automated design.
THANK YOU