DASHMESH 30 E-40 S & T 90 63 ISO 40 E-40 S & T 60 63 ... BT 40 = Shank Type (Also available in...
Transcript of DASHMESH 30 E-40 S & T 90 63 ISO 40 E-40 S & T 60 63 ... BT 40 = Shank Type (Also available in...
DASHMESHPRECISION TOOL HOLDER TECHNOLOGY
MILLENNIUM SERIES
Gage Plane
g
Dashmesh EngineeringISO/SK - TaperDIN: 69 871
Taper Ø D Ø D1 Ø D2 Ø D3± 0.05
L1 L2 L3 L4 L5
30 31.75 44.3 50 59.3 47.8 33.5 24 5.5
40 44.45 56.25 63.55 72.3 68.4 19.1 42.5 32 8.2
45 57.15 75.25 82.55 91.35 82.7 52.5 40 10
50 69.85 91.25 97.50 107.25 101.75 61.5 47 11.5
Ø dRoller
Ø d1 h7 d26H
g ±0.1
V±0.1
t-0.4
t 1-0.4
t 2-0.3
bH12
13 M12 16.4 19 15 16.1
7 17 M16 3.2 11.1 22.8 25 18.5 16.1
21 M20 29.1 31.3 24 19.3
25 M24 35.5 37.7 30 25.7
All dimensions in mm as per DIN: 69 871 (IS: 11173 - 1985)Available in Coolant Thru’ Flange & Pull Stud type also.
1
g
Gage Plane
Dashmesh EngineeringBT - TaperMAS 403 - 1982.
BT D D1 D2h8
D3±0.05
d d1H7
d2 L1±0.2
L2 L3 L4 L5+0.5
L6
30 31.75 38 50 56.144 8 12.5 M 12 48.4 20 34 24 7 17
40 44.45 53 63 75.679 10 17 M 16 65.4 25 43 30 9 21
45 57.15 73 85 100.215 12 21 M 20 82.8 30 53 38 11 26
50 69.85 85 100 119.019 15 25 M 24 101.8 35 62 45 13 31
BT g±0.4
x x1 V±0.1
b H12
t -0.2
30 2 4 8 13.6 16.1 16.3
40 2 5 10 16.6 16.1 22.6
45 3 6 12 21.2 19.3 29.1
50 3 7 15 23.2 25.7 35.4
All dimensions in mm as per MAS 403 (IS: 11173 - 1985)
2
.
Gage Gap
. . W V A
Y-Max
Ø dx
ØD
L
bL1
L2
L3
8°17'50"
AØd1
Ød2
Dashmesh EngineeringISO Taper DetailsDIN 2080 / IS 2340.
7/24 Taper
Ø D Ø d Ø d 1 Ø d 2 L L 1 L 2 L 3 b WH 12
YMax
x
ISO 30 31.75 17.4 16.5 50 70 17 3 50 8 16.1 16.2 1.6
ISO 40 44.45 25.3 24 63 95 23 5 67 10 16.1 22.5 ±0.4
ISO 50 69.85 39.6 38 100 130 17 8 105 12 25.7 35.3 3.2
ISO 60 107.95 60.2 58 160 210 35 10 165 16 25.7 60 ±0.4
All Taper Dimensions as per DIN:2080 / IS:2340 - 1972 confirming to ISO/R 297.
3
Dashmesh EngineeringLong Milling Arbor7/24 Taper
7/24Taper
D1 e L1D2min
d h6
63 100 160 200 250 315 400 500 630 800 1000 d 1 L2
27 16 X X X X X X ---- ---- ---- ---- ---- M 16x1.5 16
30 50 8 20 34 22 X X X X X X X ---- ---- ---- ---- M 20x2 22
41 27 X X X X X X X X ---- ---- ---- M 24x2 28
27 16 X X X X X X X ---- ---- ---- ---- M 16x1.5 16
34 22 X X X X X X X X ---- ---- ---- M 20x2 22
40 63 10 25 41 27 X X X X X X X X X ---- ---- M 24x2 28
47 32 X X X X X X X X X ---- ---- M 27x2 32
55 40 --- X X X X X X X X ---- ---- M 33x2 40
34 22 X X X X X X X X X ---- ---- M 20x2 22
41 27 X X X X X X X X X X ---- M 24x2 28
50 100 12 30 47 32 X X X X X X X X X X X M 27x2 32
55 40 --- X X X X X X X X X X M 33x2 40
69 50 --- ---- ---- ---- ---- ---- X X X X X M 39x3 46
84 60 --- ---- ---- ---- ---- ---- X X X X X M 45x3 56
69 50 --- ---- ---- ---- ---- ---- ---- ---- X X X M 39x3 46
60 160 16 40 84 60 --- ---- ---- ---- ---- ---- ---- ---- X X X M 45x3 56
109 80 --- ---- ---- ---- ---- ---- ---- ---- ---- X X M 56x4 63
134 100 --- ---- ---- ---- ---- ---- ---- ---- ---- X X M 68x4 70
Sizes marked ‘X’ are standard, however other sizes can also be manufactured on request. Dimensions as per IS:8614 - 1977, confirming to ISO 839/1 - 1976 Also manufactured in inch size and as per drawing. Available in Morse Taper Shanks also.
4
L 2
L
L1
ISO Taper
Holding Screw
Ø D 1
Ø D2
Ø D
Dashmesh Engineering Stub Arbor for Shell End Mill
ISOTaper D2 D
L2 Max
D1Min L1 L
HoldingScrew
16 17 32 120 M 8
30 50 22 19 40 25 122 M 10
27 21 48 124 M 12
16 17 32 147 M 8
22 19 40 25 149 M 10
40 63 27 21 48 151 M 12
32 24 58 40 169 M 16
40 27 70 172 M 20
27 21 48 203 M 12
50 100 32 24 58 40 206 M 16
40 27 70 209 M 20
50 30 90 212 M 24
Available in Morse & Metric Taper Shank also. All dimensions as per IS:8615 - 1977. Also manufactured in inch sizes.
5
L
l 2K l 1
7/24 Taper
Ø d2
Ø d1
ScrewRetaining
w x hØ d
Dashmesh Engineering Stub Arbor For Side & Face Cutter
7/24Taper
d h6
Overall Length L
d 1 K d 2 l 2 w x h Ret.Screw
For Collar Length l 1
25 63 160
16 133 171 -- 28 30 4 x 2.8 M 8
30 22 143 181 -- 36 8 50 40 6 x 4.4 M 10
27 163 201 -- 43 60 7 x 5 M 12
16 158 196 293 28 30 4 x 2.8 M 8
22 168 206 303 36 40 6 x 4.4 M 10
40 27 188 226 323 43 10 63 60 7 x 5 M 12
32 188 226 323 48 60 8 x 5 M 16
40 188 226 323 56 60 10 x 5.5 M 20
22 207 245 342 36 40 6 x 4.4 M 10
27 227 265 362 43 60 7 x 5 M 12
50 32 227 265 362 48 12 100 60 8 x 5 M 16
40 227 265 362 56 60 10 x 5.5 M 20
50 227 265 362 70 60 12 x 5.5 M 24
All dimensions as per IS: 8616 - 1977. Also manufactured in inch sizes. Available in Morse & R8 Taper also. 6
Ø D
Stopper Screw
7/24 Taper
LGage Plane
Dashmesh EngineeringCollet Chuck
Taper Collet L Ø D
ISO 30 E-40 S & T 90 63
ISO 40 E-40 S & T 60 63
ISO 50 E-40 S & T 55 63
Morse / R8-M1TR E-40 S & T 90 63
All Dimensions in mm.L = Distance from Gage plane to Nut face in locked position.Hook spanner supplied with each adapter.E - 40 S & T implies (S = Schaublin and T = Tail Type).Collets available to suit above Adapters.Also available in ER Series.
7
L
L1
Morse Taper
Ø D
7/24 Taper
Dashmesh EngineeringReduction Milling Socket
7/24 Taper Morse Taper D L 1 L
1 25 37 105
30 2 32 50 118
3 40 72 140
1 25 27 120
40 2 32 32 125
3 40 52 145
4 48 77 170
1 25 33 160
2 32 33 160
50 3 40 33 160
4 48 53 180
5 65 88 215
3 40 45 251
60 4 48 45 251
5 65 45 251
6 80 85 291
7/24 Taper dimensions as per IS:2340-1972.Morse Taper dimensions as per IS:1715-1973.Available in B-Type and C-Type also.
8
Dashmesh EngineeringSide Lock Adapter
Shank Ø D Ø D1 L L1 L2 G Shank Ø D Ø D1 L L1 L2 G
6 20 15 - M6 6 20 15 - M6
8 24 15 - 8 24 15 -
10 30 65 16 - M8 10 30 65 16 - M8
30 12 35 20 - 40 12 35 20 -
16 40 23 - M10 16 40 23 -
20 50 95 25 55/70 20/25 50 25 55/70 M10
25 50 95 25 55/70 32 60 90 30 55/70
40 70 30 55/70
Shank Ø D Ø D1 L L1 L2min/max
G
6 20 15 - M6
8 24 15 -
10 30 75 16 - M8
12 35 20 -
50 16 40 23 -
20 50 25 55/70 M10
25 50 25 55/70
32 60 105 30 55/70
40 80 30 55/70
For “WELDON” Type End Mills (DIN 1835).Available in ISO Shanks & Inch sizes also.
9
Gage Plane
Morse Taper
Ø D
L
Dashmesh EngineeringMorse Taper Adapter (Tang Type)
Shank Morse Taper Ø D L
1 25 50/120
30 2 32 65/120
3 40 80/135
1 25 45/120
2 32 60/120
40 3 40 75/120
4 50 95/165
1 25 45/120/180
2 32 45/135/180
50 3 40 45/150/180
4 50 75/180
5 70 105
Nomenclature: BT 40 / MTA 2 / 120
BT 40 = Shank Type (Also available in DIN:69871 Taper)MTA 2 =Morse Taper No. 2 Tang Type120 =Gage Plane Length (L). Gage Plane Length & Morse Taper No. However remain same for ISO Taper.
10
Morse Taper Screw Type
Gage Plane L
Ø D
Screw to Lock MT Shank (or) Special Long Pull Stud.
Dashmesh EngineeringMorse Taper Adapter (Screw Type)
Shank Morse Taper Ø D L
1 25 50/120
30 2 32 65/120
3 40 80/135
1 25 45/120
2 32 60/120
40 3 40 75/120
4 50 95/165
1 25 45/120/180
2 32 45/135/180
50 3 40 45/150/180
4 50 75/180
5 70 105
Nomenclature: BT 40 / MTB 3 / 75
BT 40 = Shank Type (Also available in DIN:69871 Taper)MTB 3 =Morse Taper No. 3 Screw Type75 =Gage Plane Length (L). Gage Plane Length & Morse Taper No. However remain same for ISO Taper.Please specify Lock method, with Screw (Supplied) or with Pull Stud (Please order).
11
Gage Plane L
H
Ø D
JT / B #
Ø C
Dashmesh EngineeringDrill Chuck AdapterJacobs & DIN 238 Taper.
Jacobs
Shank JT # L Ø D Ø C H Shank JT # L Ø D Ø C H
1 9.754 1 9.754
2 Short 13.94 3 2 Short 13.94 3
40 2 45/90 14.199 30 50 2 45/105 14.199 30
33 15.85 4 33 15.85 4
6 17.17 6 17.17
3 20.599 35 5 3 20.599 35 5
DIN 238
Shank B # L Ø D Ø C H Shank B # L Ø D Ø C H
B 6 6.35 3 B 6 6.35 3
B 10 10.095 B 10 10.095
40 B 12 45/90 12.065 30 4 50 B 12 45/105 12.065 30 4
B 16 15.733 B 16 15.733
B 18 17.431 5 B 18 17.431 5
Jacobs Taper as per IS: 9094 - 1979.B6 - 18 Taper as per DIN: 238.
12
Gage Plane
Dashmesh EngineeringShell End Mill Arbor (SMS)
Shank Ø D L L1 Ø D1 W G Shank Ø D L L1 Ø D1 W G
16 60/120 14 34 8 M 8 16 60/120 14 34 8 M 8
40 22 60/120 16 42 10 M 10 45 22 60/120 16 42 10 M 10
27 45/105 18 50 12 M 12 27 60/105 18 50 12 M 12
32 45/75 20 60 14 M 16 32 45/75 20 60 14 M 16
16 75/120 14 34 8 M 8
22 75/120 16 42 10 M 10
27 60/105 18 50 12 M 12
50 32 45/75 20 60 14 M16
40 45/75 23 70 16 M 20
50 60 26 90 18 M 24
Nomenclature: BT 40/SMS/27 - 120 BT 40 = Shank; SMS = Shell End Mill; 27 = Bore dia of Cutter; 120 = Gage plane length. Order Spanners separately. Available in ISO Shanks and Inch sizes also. All dimensions are in mm.
Note: Gage plane length is upto Face of dia ‘D1'.
13
GG
L L1
Fig 1
LL1
Fig 2
Gage Plane
Gage Plane
Ø D1 Ø D Ø D
Ø D1
W
W
Dashmesh EngineeringShoulder Cutter Arbor (FMC)
SHANK D L1 D1 L W G FIG CUTTER Ø
22 18 45 45 / 90 10 M 10 1 50 & 63
40 27 20 70 45 / 60 / 90 12 M 12 2 80
32 22 85 60 / 75 14 M 16 2 100
22 18 45 45 / 120 10 M 10 1 50 & 63
45 27 20 70 60 / 120 12 M 12 1 80
32 22 85 60 / 105 14 M 16 1 100
22 18 45 60 / 105 / 150 10 M 10 1 50 & 63
50 27 20 70 45 / 90 / 150 12 M 12 1 80
32 22 85 45 / 75 / 105 14 M 16 1 100
Nomenclature: BT 40 / FMC 22 / 90BT 40 = Shank Type (Also available in ISO Taper).FMC = Shoulder Cutter.22 = Bore Dia of Shoulder Cutter ‘D’.90 = Gage plane length.Available in ISO shanks also.Note: Gage Plane Length is only upto Face of Dia D1.
14
G
W
L
Fig 1
L1
W
Gage Plane
Ø D1 Ø D
L L1
Ø D1
Ø D
Gage Plane
Fig 2
G
G1 Ø P
Dashmesh EngineeringFace Mill Arbor (FMB)
SHANKD L1 D1 L W G G1 P FIG CUTTER Ø
27 26 80 60 / 90 12 M 12 - - 80
40 32 26 80 60 / 90 14 M 16 - - 1 100
40 26 85 60 / 75 16 M 20 - - 125
27 26 80 45 / 90 /150
12 M 12 - - 80
32 26 80 60 / 90 14 M 16 - - 1 100
50 40 26 85 45 / 75 /105
16 M 20 - - 125
40 F 26 110 75 16 M 20 M 12 66.7 2 160
60 25 140 75 25.4 - M 16 101.6 2 200 - 500
Nomenclature: BT 40 / FMB / 32 / 60BT 40 = Shank Type (Also available in ISO Taper).FMB = Face Mill.32 = Bore Dia of Face Mill ‘D’.60 = Gage plane length.Available in ISO / TC shanks also.Spanners to be ordered separately.Note: Gage Plane Length is only upto Face of Dia D1.
G
W
Gage Plane
Ø D A/F
H
30L
Ø C
Dashmesh EngineeringSide & Face Mill Arbor(Stub Arbor) SCA
Shank Ø D L H A/F C W G
13 75/105 120/150 17 20 - M12x1.25
16 75/105 121/151 23 26 4 M14x1.5
40 22 75/120 126/171 29 34 6 M20x1.5
27 75/120 130/175 32 40 7 M24x2.0
32 90 150 41 46 8 M30x2.0
13 75/105 120/150 17 20 - M12x1.25
16 90/120 136/166 23 26 4 M14x1.5
45 22 141/186 29 34 6 M20x1.5
27 90/135 145/190 32 40 7 M24x2.0
32 150/195 41 46 8 M30x2.0
13 75/105 120/150 17 20 - M12x1.25
16 90/120 136/166 23 26 4 M14x1.5
50 22 144/186 29 34 6 M20x1.5
27 90/135 145/190 32 40 7 M24x2.0
32 150/195 41 46 8 M30x2.0
40 156/201 46 55 10 M36x3.0
Nomenclature : BT 40 / SCA / 32 / 135BT 40 = Shank.SCA = Side & Face Cutter. 32 = Bore dia of Cutter.135 = Length from Gage Plane.
Also available in ISO Taper Shanks and Inch sizes.All dimensions in mm.Note: Gage Plane Length is only upto the Face of dia ‘C’.
15
Gage Plane
Gage Plane
Dashmesh EngineeringRough Boring Bar Angular Mounting (BSA)
Shank Ø D Min Ø D Max L C W G E
25 38 135 20 8 M6 1.0
30 42 150 24 8 M6 1.6
38 52 165 30 10 M8 2.6
40 50 65 165/210 40 12 3.0
62 90 165/225 50 M10 2.0
72 110 165/225 60 16 2.4
90 125 165/210 75 M12 4.0
25 38 135 20 8 M6 1.0
30 42 165 24 1.6
38 52 180 30 10 M8 2.6
45 42 56 210 34 2.0
50 65 180/225 40 12 3.0
62 90 195/270 50 M10 2.0
72 110 195/285 60 16 2.4
90 125 195/285 75 M12 4.0
16
Gage Plane
Gage Plane
Dashmesh EngineeringRough Boring BarAngular Mounting (BSA)
Shank Ø D Min Ø D Max L C W G E
25 38 135 20 8 M6 1.0
30 42 165 24 1.6
38 52 180 30 10 M8 2.6
42 56 210 34 2.0
50 50 65 180/240 40 12 3.0
62 90 195/270 50 M10 2.0
72 110 195/285 60 2.4
90 125 210/300 75 16 4.0
105 160 195/285 90 M12 3.0
130 190 255 110 6.0
Driving Slot and Tool are in same plane.L & E correspond to D Minimum.Boring Bar supplied without Tool / Cartridge.Also same sizes available for Micro (Fine) Boring (BCA) & Rough Boring Square Mounting (BSB).
17
Stopper Screw
Gage Plane
L
ØD
Dashmesh EngineeringCollet Chuck
Shank Collet Type L ØD
ER 16 28
30 ER 20 70 34
ER 32 50
ER 16 28
ER 20 70 34
40 ER 25 42
ER 32 50
ER 40 80 63
ER 32 100 50
50 ER 40 80 63
ER 50 100 78
Nomenclature: BT 40 / 70 / ER 40 BT-40 = Shank; 70 = Gage Plane Length; ER 40 = Collet Type.Also available for collets like, M - Series; E - Series; Double Angle, TG - Series etc.Collet chucks are offered with nut and hook spanner.Available in ISO Taper Shanks also.
19
2
L1
L
L
ØD
Fig-1
G
ØD
L
Fig-2 Fig-3
L1L1
G G
Ød2 Ød 2
Ød
ØD
Dashmesh EngineeringPull Studs
Fig - 1 MAS-403 Fig - 2 DIN:69872
Shank G L L1 D è d Shank G L L1 D è d
30 M12 43 23 16.5 45 / 60 - 30 M12 44 24 13 15 -
40 M16 60 35 23 45 / 60 / 90 - 40 M16 54 26 17 15 7.5
45 M20 70 40 31 45 / 60 / 90 - 45 M20 65 30 21 15 9.5
50 M24 85 45 38 45 / 60 / 90 - 50 M24 74 34 25 15 11.5
ISO 7388/2
Shank G L L1 D è d
40 M16 44.5 16.4 22.5 45 / 60 7.5
45 M20 56 20.95 30 45 / 60 9.5
50 M24 65.5 25.55 37 45 / 60 11.5
Also available as Per JIS:B6339, ANSI, CAT, OTT etc. with & without thru’ coolant.
20
r
L ± 0.1
Ø D g6
Ø d H7
b
Dashmesh Engineering
Running Bush
Ø dH7
aC11
b r D L D L D L D L D L D L D L y
Max 42 60 48 70 56 80 70 100 85 120 110 140 140 160
16 4 17.7 +0.1 0.5 X X X X X X 0.05
22 6 24.1 0 1.0 X X X X X X X X X X
27 7 29.8 X X X X X X X X X X
32 8 34.8 1.2 X X X X X X X X
40 10 43.5 X X X X X X
50 12 53.5 +0.2 1.6 X X X X X X 0.08
60 14 64.2 0 X X
80 18 85.5 2.0 X X
100 25 107 2.5 X X
Parallelism of Faces, t 0.004 0.005 0.006
Concentricity, Z 0.008 0.010 0.012
Items marked ‘X’ are standard sizes, however other sizes can be made on request. All dimensions are in mm & as per IS: 8619 - 1977 confirming to ISO 839/II - 1977. Available in inch sizes also.
21
Dashmesh EngineeringSpacers
Ø d C11 16 22 27 32 40 50 60 80 100
Ø D1 h11 for L$10 27 34 41 47 55 69 84 109 134
Ø D2 h11 for L<10 26 33 40 46 54 68 83 -- --
a C11 4 6 7 8 10 12 14 18 25
b 17.7 24.1 29.8 34.8 43.5 53.5 64.2 85.5 107
Tolerance on b
+0.10
+0.20
r Max 0.6 1 1.2 1.2 1.2 1.6 1.6 2 2 .5
c 0.4 0.4 0.4 0.6 0.6 0.6 0.6 1 1
z 0.05 0.08
L ± 0.1
1, 2, 3, 6
10
--
20
30
-- 60
-- 100
t Parallelism offaces 0.004 0.005 0.006
* Recess only for L öö 60mm.All Dimensions in mm and as per IS:8618 - 1977.Available in Inch sizes also.
22
LL1
Ø D
Morse Taper
Dashmesh EngineeringMORSE TAPER COLLET CHUCK
COLLET E - 40 & ER - 40: COLLET E - 45:-
TAPER Ø D L1 L TAPER Ø D L1 L
2 63 74 146 2 71 80 152
3 63 74 165 3 71 80 171
4 63 74 190 4 71 80 196
5 63 70 226 5 71 70 226
6 63 42 260 6 71 42 260
Ordering Nomenclature : MT-3 x E-40.The dimensions remain same for Screw Type, except Dim L.Morse Taper will have Cotter Pin Slot.Spanned included in Standard Supply
23
8°25'30"
Ø 24.1
L
l
Ø D
Ø 48
Dashmesh EngineeringR8 / M1TRCollet Chuck
Taper Collet Ø D l L
E / ER 32 50
R8 / M1TR E / ER 40 63 76 176
E / ER 50 78
Collet adapter supplied with Hook Spanner.Available for collets of customers choice against request.
24
L
8°25'30"
24
Ø DØ 24.1
2L 1
78
Dashmesh EngineeringReduction Milling SocketR8 / M1TR Taper.
MorseTaper
Ø D L L1
1 32 114 14
2 32 114 14
3 36 174 74
L1 = Distance from Gage Plane, based on our own design.Morse Taper dimensions as per IS:1715-1973.
25
8°25'30"
Ø 24.1 Ø d
ll 1
Ø d1
L
Dashmesh EngineeringR8 / M1TRStub Arbor
Taper Ø d l Ø d1 l1 L
16 17 32 144
R8 / M1TR 22 19 40 25 146
27 21 48 148
R8 Taper Standard.Gage Gap 2mm.“Ød” & “l” Dimensions as per IS:8615 - 1977.Also manufactured in “INCH” sizes.
26
Ø D
L
Dashmesh EngineeringDrill SleeveIS:6702 - 1972
OD 2 3 3 4 4 4 5 5 5 6 6 6
ID 1 1 2 1 2 3 2 3 4 3 4 5
Ø D 18.6 24.1 24.8 31.6 31.6 32.3 44.7 44.7 45.4 63.8 63.8 63.8
L 91 98 111 123 123 139 155 155 170 217 217 217
Morse Taper dimensions as per IS:1715-1973.Case Hardened and Ground 56/58 HRc.
27
Ø D
L2
L1
Dashmesh EngineeringEXTENSION SOCKET IS : 6692-1972
Outer MT 1 1 2 2 2 3 3 3 3
Inner MT 1 2 1 2 3 1 2 3 4
Ø D 20 30 20 30 36 20 30 36 48
L- 1 76 91 76 91 112 76 91 112 137
L- 2 145 160 160 175 196 175 194 215 240
Outer MT 4 4 4 4 4 5 5 5 5 5
Inner MT 1 2 3 4 5 1 2 3 4 5
Ø D 20 30 36 48 63 20 30 36 48 63
L- 1 76 91 112 137 172 76 91 112 137 172
L- 2 200 215 240 265 300 232 247 268 300 335
Ordering Nomenclature : ES-23 (Extension Socket Outer MT-2 x Inner MT-3)
28
Fig 3
Fig 2
Fig 1
Dashmesh EngineeringMicro Boring Bars
29
Dashmesh EngineeringMicro Boring Bars
TaperShank
Boring Bar Ø D BoringRange
L C1 C2 L1 MicroboreUnit
Fig #. ApproxWt.
12.7 - 105 12.7 - 15 105 - 12.5 M1 S2 1.5
12.7 - 165 165 44 67 2.0
14.5 - 105 14.5 - 17 105 - 14 1.5
14.5 - 165 165 44 2.0
16 - 105 16 - 22.5 105 - 15 73 M1 L2 1.5
16 - 165 165 44 2.0
19 - 120 19 - 23 120 - 18 86 M2 S2 1.5
19 - 180 180 44 1 2.0
23 - 135 23 - 29 135 - 22 105 M3 S2 1.5
23 - 195 195 44 2.0
29 - 150 29 - 41 150 - 28 M3 L2 1.5
40 29 - 195 195 55 115 2.0
38 - 150 38 - 49 150 - 35 M5 S2 1.5
38 - 210 210 55 37 172 2.5
46 - 150 46 - 66 150 - 41 115 M5 L2 2.5
46 - 225 225 55 44 182 3.0
62 - 165 62 - 87 165 - 51 133 2 3.5
62 - 225 225 - 57 185 M7 L2 1 4.5
83 - 165 83 - 108 165 - 63 - 2 4.5
83 - 225 225 - - 6.0
98 - 165 98 - 142 165 - 83 - M10 L2 3 6.0
Note: Drive Slot & Tool are in Same Plane. ‘L’ & ‘L1" Show size at ‘D’ Min.
30
Dashmesh EngineeringMicro Boring Bars
TaperShank
Boring Bar Ø D BoringRange
L C1 C2 L1 MicroboreUnit
Fig #. ApproxWt.
12.7 - 120 12.7 - 15 120 12.5 M1 S2 4
12.7 - 195 195 67 5
14.5 - 120 14.5 - 17 120 14 4
14.5 - 195 195 5
16 - 120 16 - 22.5 120 15 73 M1 L2 4
16 - 195 195 44 5
19 - 135 19 - 23 135 18 86 M2 S2 4
19 - 210 210 1 5
23 - 150 23 - 29 150 22 105 M3 S2 4
23 - 225 225 5
29 - 165 29 - 41 165 28 M3 L2 4.5
50 29 - 225 225 115 5.5
38 - 165 38 - 49 165 - 35 M5 S2 4.5
38 - 225 225 55 37 172 5.5
46 - 165 46 - 66 165 - 41 115 M5 L2 5
46 - 225 225 55 44 182 5.5
62 - 180 62 - 87 180 - 51 137 2 6
62 - 240 240 - 57 184 M7 L2 1 7
83 - 165 83 - 108 165 - 63 122 1 6.5
83 - 240 240 - 70 190 9
98 - 165 98 - 142 165 - 83 122 2 8.5
98 - 240 240 - 197 11.5
132 - 210 132 - 176 210 - 108 12
132 - 315 315 - M10 L2 18.5
166 - 225 166 - 210 225 - 142 - 3 13
166 - 315 315 - 18.5
200 - 210 200 - 244 210 - 176 20
31
Few of our Products
DASHMESH ENGINEERING
C O M P A N Y – P R O F I L E
Mr. Pritam Singh Mogewala established a Small Scale Industry in the eve of 1979 at Bangalore,
the cradle of Machine Tool building in India. In 1981 we
moved to our own premises at Peenya (Bangalore) Asia’s
largest Industrial complex. With a humble beginning,
having started with a small area of 750 Sq. Ft, today we
cover nearly 8000 Sq. Ft. space.
We started with manufacturing of Long Milling Arbors as
OEM suppliers to reputed Milling Machine builders in India.
With his hard work and
sincerity he developed the “DASHMESH” brand to be synonym
with quality and precision. Today, apart from manufacture of
Long Milling Arbors & Hob Arbors, we are also into CNC
Toolings, Main Spindles, Splined Shafts, Draw-Bars etc., &
Heavy Parts like Column, Saddle, Cross Slide, HeadStock for
Milling Machines, VMC’s, HMC’s and CNC Lathes.
# 255, 8th Cross, 4th Phase Peenya Industrial Area Bangalore – 560 058. INDIA Telephone : 080-28397330, 28392371 Fax : 91-80-51179160 E-mail : [email protected]
Mr. Pritam Singh Mogewala
Mitsubishi MPA 80A HMC
Warner & Swasey WSU-12 Universal Turning Center
We are India’s largest manufacturers of Long & Stub Milling arbors and have the reputation of
being second to none, and are exporting to highly quality conscious markets in North America,
Europe, Singapore & Japan.
We have an impressive list of OEM customers like BFW,
BATLIBOI, LMW, AMS, ACE DESIGNERS etc., and among our
Overseas OEM’s we have MAKINO, WMW, & DMG. Apart
from this our end users include the best from Automotive, Aeronautics – Aerospace and
Defence sector.
After a decade of operations at the existing facility, we were
again cramped for space and in 1994 we added an additional
facility having 5000 square feet of space as our Unit-II
equipped with latest CNC Machines and Digital measuring
instruments.
We have installation of highly acclaimed Mother Machines like MITSUBISHI Horizontal
Machining Center, WARNER & SWASEY Universal Turning Center, BFW Vertical & Horizontal
Milling Machines, HMT Center Lathes, HMT Cylindrical & Universal Grinders, FRITZ WERNER
Spline Grinder, TOS Surface Grinder, COOPER Slotting Machine and supporting machines like
Bench Drills, 2-D Pantograph, Bench Grinders, Power Hacksaw, Tool & Cutter Grinder.
Dashmesh EngineeringBangalore -58
Machinery - List
• CNC HORIZONTAL MACHINING CENTER
MITSUBISHI DIAMATIC MPA 80 A
Table:-
Pallet = 1000 x 1000mm Twin.Index = 360 x 1° min.Loading Capacity = 2000Kg. Max. each Pallet.
X-axis Travel for Table:-
Total Travel = 1500mm.From Spindle Centre = " 750mm.
Y-axis Travel for Table:-
Total Travel = 1000mm.Above Table = 0 - 1000mm.
Z-axis Travel for Column:-
Total Travel = 800mm.Between Spindle & Table Centre = 350 - 1150mm.
ATC:-60 Tools Magazine.
CNC System:-
Fanuc 6M model B.
Spindle Nose Taper:-
BT-50 (7/24 Taper) JIS B6101 No.50.Speed 20 – 2000 RPM Infinitely Variable.
• CNC UNIVERSAL TURNING CENTER
MIVEN WARNER & SWASEY WSU – 12.
Main Spindle = A2 – 8.Chuck Size = Ø 315mm Hollow Hyd. Actuation.Max. Turning Dia between Centers = Ø 380mm.Max. Turning Dia Chucking = Ø 660mm.Max. Turning Length = 1000mm.Spindle Speed Range = 30 - 3000rpm Infinitely Variable.Spindle Power Rating = 18.5/22 kW.Rapid Traverse = 12 M/min.Turret = 12 Station W & S Drum Type.Tail Stock = MT-4 Programmable.CNC System = Fanuc Oi TA Color Display with AC unit.Steady Rest = 30 - 150mm Hydraulic.
Dashmesh EngineeringBangalore -58
• Centre LatheHMT H – 22 / 1000 = 2 Nos.HMT VIKRAM / 1500 = 1 No.HMT L – 22 / 1000 = 1 No.VINOD / 4.5 Ft = 1 No.
• MillingBFW VF – 2 = 1 No.BFW UF – 1 = 1 No.
• SlottingCOOPER CH – 25 = 1 No. (Stroke length 250mm with Rotary Index Table)
• Surface GrindingTOS 600 x 200 HORIZONTAL = 1 No.
• Cylindrical GrindingHMT K – 130 / 800 U = 1 No.HMT G – 13 / 500 = 1 No.
• Spline GrindingFritz Werner 3.275/1.2 = 1 No. (Max. Length 1000mm Spline Shaft)
• 2 – D PantographF.I.E. Denmark = 1 No.
• Bench DrillingTOOL CRAFT = 1 No.JAYESH = 1 No.
• Tool & Cutter GrinderAMBASANA 225 x 150 U = 1 No.
• Power HacksawVEEKAY Ø 175mm Capacity = 1 No.VEEKAY Ø 200mm Capacity = 1 No.
• Bench GrinderELMACO = 2 Nos.
DASHMESH ENGINEERINGBangalore – 560 058.
Measuring Instruments
• Vernier Calipers
0 - 200 = 3 Nos. Mitutoyo 0 - 200 = 1 No Mitutoyo Digital 0 - 300 = 1 No Baker Digital 0 - 150 = 1 No JIS Digital 0 - 300 = 2 Nos. Mitutoyo 0 - 200 = 1 No. Depth Vernier Mitutoyo 0 - 1000 = 1 No. Mitutoyo
• Micrometers
0 - 25 = 1 No. Mitutoyo Digital 0 - 25 = 3 Nos. Mitutoyo 25 - 50 = 3 Nos. Mitutoyo 50 - 75 = 2 Nos. Mitutoyo 75 - 100 = 1 No Mitutoyo 100 - 125 = 1 No Mitutoyo 150 - 300 = 1 No Mitutoyo
• Internal Micrometers 3-Point
12 – 20 = 1 Set Mitutoyo20 – 50 = 1 Set Mitutoyo50 – 100 = 2 Sets Mitutoyo
• Bore dial Gage
10 - 18mm = 2 Set Mitutoyo 18 - 35mm = 2 Set Mitutoyo 35 - 60mm = 1 Set Mitutoyo 50 - 150mm = 2 Set Mitutoyo
• Height Gage
0 – 300 = 1No Mitutoyo
• Dial Gages
0.001 = 1 No. Mahr Millimess 0.01 = 3 Nos. Mitutoyo - Plunger Type 0.001 = 3 Nos. Mitutoyo - Plunger Type 0.01 = 1 No Baker - Lever Type 0.002 = 1No Mitutoyo - Lever Type 0.01 = 1 No. Mitutoyo - Lever Type
DASHMESH ENGINEERINGBangalore – 560 058.
• Bevel Protractor
"VIS" Poland = 1 No "Mitutoyo" Japan = 1 No
• Thread Plug Gages
M - 06 = 2 Nos. Accurate/HIP M - 10 = 2 Nos. Accurate/HIP M - 12 = 2 Nos. Accurate/HIP M - 16 = 2 Nos. Accurate/HIP M - 24 = 2 Nos. Accurate/HIP M - 30 = 2 Nos. Accurate/HIP
• Ring Gages
ISO – 30 7/24 = 1 No Self ISO – 35 7/24 = 1 No Self ISO – 40 7/24 = 1 No Self ISO – 45 7/24 = 1 No Self ISO – 50 7/24 = 1 No Sonalkar ISO – 60 7/24 = 1 No Sonalkar M1TR / R8 = 1 no Self MT – 1 / 2 / 3 / 4 / 5 / 6 = 1 No Each Self Ø 16 - Ø 50 = 1 No Each "Accurate" E - 40 Schaublin Collet Gage = 1 No Self E - 40 Tail Type Collet Gage = 1 No Self E - 32 Collet Gage = 1 No Self
• Plug Gages
ISO – 30 7/24 = 1 No Self ISO – 35 7/24 = 1 No Self ISO – 40 7/24 = 1 No Self ISO – 45 7/24 = 1 No Self ISO – 50 7/24 = 1 No Self ISO – 60 7/24 = 1 No Self MT - 1/2/3/4/5/6 = 1 No Each Self 1/16 Taper = 1 No Self E - 40 Schaublin Collet Gage = 1 No Self E - 32 Collet Gage = 1 No Self ER - 40 Collet Gage = 1 No Self E – 40 Tail Collet Gage = 1 No. Self Metric 80 = 1No Self Ø 5 - Ø50mm - 1 No Each "Accurate" & "HIP"
• Sine Bar
100mm Long = 1 No
DASHMESH ENGINEERINGBangalore – 560 058.
• Slip Gage
USSR Make = 1 No "Matrex" Indian = 1 No
• Hardness Tester
"Fine" Make = 1 No
• Concentricity Tester
Self-made = 1 No.
• Test Mandrels
ISO-40 Ø 30 x 300 = 1 No. Run-Out 0.002mm. Self made.SK-40 Ø 30 x 300 = 1 No. Run-Out 0.002mm. Self made.BT-40 Ø 30 x 300 = 1 No. Run-Out 0.002mm. Self made.ISO-50 Ø 40 x 300 = 1 No. Run-Out 0.002mm. Self made.SK-50 Ø 40 x 300 = 1 No. Run-Out 0.002mm. Self made.BT-50 Ø 40 x 300 = 1 No. Run-Out 0.002mm. Self made.Mores Taper Test Mandrels MT-2/3/4/5/6 = 1 No each Run-Out 0.002mm, Self Made.
• Granite Table
600 x 600 = 1 No " VTG" 1600 x 1200 x 200 = 1 No. “MMT”
-- * -- * -- * --
Dashmesh EngineeringBangalore - 560058.
CUSTOMER LIST
1. M/s. BHARAT FRITZ WERNER LIMITED, BANGALORE.
2. M/s. BATLIBOI LIMITED, UDHNA.
3. M/s. WMW MACHINERY INC., NEW YORK, USA.
4. M/s. LAKSHMI MACHINE WORKS LIMITED, COIMBATORE.
5. M/s. BATLIBOI SPM’s LIMITED, BANGALORE.
6. M/s. DECKEL MAHO GILDEMEISTER (INDIA) LIMITED, BANGALORE.
7. M/s. MAKINO ASIA LIMITED, BANGALORE.
8. M/s. ACE DESIGNERS LIMITED, BANGALORE.
9. M/s. ACE MANUFACTURING SYSTEMS LIMITED, BANGALORE.
10. M/s. MIVEN MACHINE TOOLS LIMITED, HUBLI, KARNATAKA.
11. M/s. ELGI EQUIPMENTS LIMITED, COIMBATORE.
12. M/s. L & T DEMAG PLASTIC MACHINERY LIMITED, CHENNAI.
Dashmesh EngineeringBangalore - 560058.
PRODUCTS
1. MAIN SPINDLES for Milling Machines, Vertical & Horizontal Machining Centers,CNC Lathes and Special Purpose Machines.
2. TOOL HOLDERS like Long & Stub Milling arbors, Hob Arbors, CNC Toolings,
Milling Sockets, ATC Alignment Fixtures,
Drawbars, Test Mandrels and other special
machine tool accessories.
Dashmesh EngineeringBangalore - 560058.
3. Heavy Parts for VMC, HMC & CNC Lathes.
Saddle of ACE Designers CNC Lathe Column of AMS VMC
Column of HOWA HMC Cross Slide of Warner & Swasey CNC Lathe
Contact
POST: -
DASHMESH ENGINEERINGD-423, 10th MAIN, 2nd STAGE,PEENYA INDISTRIAL ESTATE,BANGALORE – 560058.KARNATAKAINDIA
PHONES: -
Land Phones = 00-91-80-28397330 / 28392371 / 28360769Hand Phone = 0094483-65962Facsimile = 00-91-80-41179160
E-MAIL: -
1) [email protected]) [email protected]
DIRECTIONS: -
From Bangalore drive down NH-4 towards Pune. (Approx. 11Kms from City Railway Stn.)At Jalahalli Cross take left to enter Peenya Industrial Area. (Traffic Junction with Signals)Continue for Approx. 1Km to reach TVS Cross. (Traffic Junction with Signals)Here take Right Turn and continue for Approx. 1KM towards NTTF Cross.At NTTF Cross turn Left towards Peenya II Stage, and take immediate left on 8th Cross.As you enter 8th Cross, the LEFT CORNER is your Destination.