(203) 262-9245 EVALUATION REPORT Evaluation Report … · EXTERIOR RESEARCH & DESIGN, LLC....

EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization #9503

353 Christian Street Oxford, CT 06478 (203) 262-9245

EVALUATION REPORT

CertainTeed Corporation 20 Moores Road Malvern, PA 19355 (610) 651-5847

Evaluation Report 3520.03.04-R19 FL2533-R18

Date of Issuance: 09/19/2005 Revision 19: 06/06/2017

SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for compliance with the 5th Edition (2014) Florida Building Code sections noted herein.

DESCRIPTION: Flintlastic® Modified Bitumen Roof Systems

LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.

CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. Trinity|ERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle.

ADVERTISEMENT: The Evaluation Report number preceded by the words “Trinity | ERD Evaluated” may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.

INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official.

This Evaluation Report consists of pages 1 through 6, plus a 57-page Appendix. Prepared by:

Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCA ANE1983

The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 06/06/2017. This does not serve as an electronically signed document. Signed, sealed hardcopies have been transmitted to the Product Approval Administrator and to the named client

CERTIFICATION OF INDEPENDENCE: 1. Exterior Research & Design, LLC. d/b/a Trinity | ERD does not have, nor does it intend to acquire or will it acquire, a financial interest

in any company manufacturing or distributing products it evaluates. 2. Exterior Research & Design, LLC. d/b/a Trinity | ERD is not owned, operated or controlled by any company manufacturing or

distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for

which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the

product. 5. This is a building code evaluation. Neither Trinity|ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any

project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose.

Exterior Research and Design, LLC. Evaluation Report 3520.03.04-R19 Certificate of Authorization #9503 FBC NON-HVHZ EVALUATION FL2533-R18

CertainTeed Corporation Revision 19: 06/06/2017 of 6

ROOFING SYSTEMS EVALUATION:

1. SCOPE:

Product Category: Roofing Sub-Category: Modified Bitumen Roof Systems Compliance Statement: Flintlastic® Modified Bitumen Roof Systems, as produced by CertainTeed Corporation, have demonstrated compliance with the following sections of the 5

th Edition (2014) Florida Building Code through

testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein.

2. STANDARDS:

Section Property Standard Year 1504.3.1 Wind FM 4474 2004 1504.7 Impact FM 4470 1992 1507.11.2 Physical Properties ASTM D6162 2000 1507.11.2 Physical Properties ASTM D6163 2000 1507.11.2 Physical Properties ASTM D6164 2005 1507.11.2 Physical Properties ASTM D6222 2008 1507.11.2 Physical Properties ASTM D6509 2009

3. REFERENCES:

Entity Examination Reference Date ERD (TST6049) FM 4470 3504.06.01-1 06/05/2001 ERD (TST6049) FM 4470 3513.08.02 08/15/2002 ERD (TST6049) FM 4470 03515.07.03 07/22/2003 ERD (TST6049) FM 4470 3519.12.03 12/22/2003 ERD (TST6049) FM 4470/4474 3522.07.04 07/28/2004 ERD (TST6049) FM 4470/4474 02843.02.05-11 02/10/2005 ERD (TST6049) FM 4470/4474 3533.01.06 01/06/2006 ERD (TST6049) FM 4470/4474 4674.11.01-1 03/21/2006 ERD (TST6049) Physical Properties 3535.10.06 10/31/2006 ERD (TST6049) FM 4470/4474 3521.07.04-R1 10/26/2007 ERD (TST6049) FM 4470/4474 02764.09.05-R1 12/10/2007 ERD (TST6049) FM 4470/4474 02762.03.05-R1 12/10/2007 ERD (TST6049) Physical Properties C7290.01.08 01/16/2008 ERD (TST6049) Physical Properties C10080.09.08 09/04/2008 ERD (TST6049) FM 4470/4474 C8370.08.08-R1 10/05/2009 ERD (TST6049) FM 4470/4474 P6860.06.07-R1 09/10/2009 ERD (TST6049) FM 4470/4474 C30310.12.09 12/17/2009 ERD (TST6049) FM 4470/4474 C30560.03.10 03/18/2010 ERD (TST6049) FM 4470/4474 C31420.08.10 09/21/2010 ERD (TST6049) FM 4470/4474 C33980.12.10 12/22/2010 ERD (TST6049) FM 4470/4474 C33830.02.11 02/08/2011 ERD (TST6049) TAS 117(B), Rupture C35500.02.11 02/09/2011 ERD (TST6049) FM 4470/4474 C37820.07.12 07/24/2012 ERD (TST6049) FM 4470/4474 C37830.07.12 07/26/2012 ERD (TST6049) Physical Properties C42110.08.12 08/13/2012 ERD (TST6049) FM 4470/4474 C39670.08.12 08/20/2012 ERD (TST6049) FM 4470/4474 C42280.08.12 08/20/2012 ERD (TST6049) TAS 117(A) A35880.04.12-R1 10/26/2012 ERD (TST6049) FM 4470/4474 C44580.07.13 07/25/2013 ERD (TST6049) FM 4470/4474 C46090.11.13-A 11/20/2013 ERD (TST6049) FM 4470/4474 C45620.03.14 03/27/2014 ERD (TST6049) FM 4470/4474 C46760.06.14 06/19/2014 ERD (TST6049) FM 4470/4474 C47320.03.14-R1 04/01/2015 ERD (TST6049) FM 4470/4474 CTR-SC8995.10.15 10/14/2015 ERD (TST6049) FM 4470/4474 CTR-SC9935.01.16 01/14/2016 ERD (TST6049) FM 4470 CTR-SC9920.01.16-R1 01/20/2016 ERD (TST6049) FM 4470/4474 CTR-SC10420.01.16 01/25/2016 ERD (TST6049) FM 4470/4474 CTR-SC9175.09.16-1 09/06/2016



Entity Examination Reference Date ERD (TST6049) FM 4470/4474 CTR-SC9175.09.16-1 09/06/2016 ERD (TST6049) FM 4470/4474 CTR-SC11590.08.16-R1 09/06/2016 ERD (TST6049) FM 4470/4474 CTR-SC12255.12.16 12/27/2016 FM Approvals (TST1867) FM 4470 0E3A2.AM 03/30/1982 FM Approvals (TST1867) FM 4470 3W0A4.AM 03/16/1993 FM Approvals (TST1867) FM 4470 3W0A2.AM 03/17/1993 FM Approvals (TST1867) FM 4470 3W0A3.AM 03/17/1993 FM Approvals (TST1867) FM 4470 1Z4A6.AM 09/11/1996 FM Approvals (TST1867) FM 4470 3Y8A1.AM 09/30/1996 FM Approvals (TST1867) FM 4470 2D5A9.AM 06/22/1999 FM Approvals (TST1867) FM 4470 3009502 12/12/2000 FM Approvals (TST1867) FM 4470 3008869 03/19/2001 FM Approvals (TST1867) FM 4470 3009610 10/15/2001 FM Approvals (TST1867) FM 4470 3006025 12/28/2001 FM Approvals (TST1867) FM 4470 3012321 07/29/2002 FM Approvals (TST1867) FM 4470 3009814 09/06/2002 FM Approvals (TST1867) FM 4470 3014502 04/04/2003 FM Approvals (TST1867) FM 4470 3015444 07/11/2003 FM Approvals (TST1867) FM 4470 3014692 08/05/2003 FM Approvals (TST1867) FM 4470 3014751 08/27/2003 FM Approvals (TST1867) FM 4470 3018579 10/09/2003 FM Approvals (TST1867) FM 4470/4474 3020703 07/30/2004 FM Approvals (TST1867) FM 4470/4474 3021759 06/03/2005 FM Approvals (TST1867) FM 4470/4474 3022038 04/05/2006 FM Approvals (TST1867) FM 4470/4474 3023458 07/18/2006 FM Approvals (TST1867) FM 4470/4474 3026128 08/04/2006 FM Approvals (TST1867) FM 4470/4474 3024311 11/01/2006 FM Approvals (TST1867) FM 4470/4474 3025766 11/13/2006 FM Approvals (TST1867) FM 4470/4474 3028410 02/19/2007 FM Approvals (TST1867) FM 4470/4474 3026964 07/25/2007 FM Approvals (TST1867) FM 4470/4474 3031262 11/30/2007 FM Approvals (TST1867) FM 4470/4474 3031199 12/23/2008 FM Approvals (TST1867) FM 4470/4474 3032172 06/12/2009 FM Approvals (TST1867) FM 4470/4474 3037127 01/11/2010 FM Approvals (TST1867) FM 4470/4474 3039848 12/02/2011 FM Approvals (TST1867) FM 4470/4474 3046104 08/13/2013 FM Approvals (TST1867) FM 4470/4474 3048520 09/19/2013 MTI (TST2508) Physical properties DX08C4A 03/22/2004 MTI (TST2508) Physical properties DX20E3A 03/22/2004 MTI (TST2508) Physical properties DX20E3A-001 01/04/2006 MTI (TST2508) Physical properties AX31G8A 08/21/2008 MTI (TST2508) Physical properties AX31G8D 09/05/2008 MTI (TST2508) Physical properties AX31G8F 06/05/2009 MTI (TST2508) Physical properties AX21G8C 01/28/2011 PRI (TST5878) Physical Properties CTC-032-02-01 01/16/2008 PRI (TST5878) Physical Properties CTC-034-02-01 11/24/2008 PRI (TST5878) Physical Properties CTC-066-02-01 08/08/2011 PRI (TST5878) Physical Properties CTC-067-02-01 08/08/2011 PRI (TST5878) Physical Properties CTC-068-02-01 08/08/2011 PRI (TST5878) Physical Properties CTC-070-02-01 08/08/2011 PRI (TST5878) Physical Properties CTC-071-02-01 08/08/2011 PRI (TST5878) Physical Properties CTC-093-02-01 08/08/2011 PRI (TST5878) Physical Properties CTC-116-02-01 04/03/2012 PRI (TST5878) Physical Properties CTC-183-02-01 10/04/2013 PRI (TST5878) Physical Properties CTC-259-02-01 12/11/2015 UL, LLC. (QUA9625) Quality Assurance Service Confirmation, R11656 Exp. 07/03/2017



4. PRODUCT DESCRIPTION:

This Evaluation Report covers Flintlastic® Modified Bitumen Roof Systems installed in accordance with CertainTeed Corporation published installation instructions and the Limitations / Conditions of Use herein. The following CertainTeed products make up the subject systems.

TABLE 1: ROLL-GOODS FOR FLINTLASTIC® MODIFIED BITUMEN ROOF SYSTEMS

Type Product

Specification

Reference Grade Type

Base Sheets

Flintlastic® SA NailBase ASTM D4601 N/A II

Glasbase™ Base Sheet ASTM D4601 N/A II

All Weather/Empire™ Base ASTM D4601 N/A II

Flexiglas™ Base ASTM D4601 N/A II

Flintlastic™ Base 20 ASTM D4601 N/A II

Flintlastic Poly SMS Base Sheet ASTM D4601 N/A II

Yosemite® Venting Base ASTM D4897 N/A II

Ply Sheets

Flintglas® Ply 4 ASTM D2178 N/A IV

Flintglas® Premium Ply 6 ASTM D2178 N/A VI

Base/Ply Membranes (APP)

Flintlastic® APP Base T ASTM D6509 N/A N/A

Flintlastic® STA ASTM D6222 S I

Flintlastic® STA Plus ASTM D6222 S I

Cap Membranes (APP)

Flintlastic® STA ASTM D6222 S I

Flintlastic® STA Plus ASTM D6222 S I

Flintlastic® GTA ASTM D6222 G I

Flintlastic® GTA CoolStar™ ASTM D6222 G I

Flintlastic® GTA-FR ASTM D6222 G I

Flintlastic® GTA-FR CoolStar™ ASTM D6222 G I

Base/Ply Membranes (SBS)

Flintlastic® SA PlyBase ASTM D1970 N/A N/A

Black Diamond® Base Sheet ASTM D1970 N/A N/A

Flintlastic® SA Mid Ply ASTM D6163 S I

Flintlastic® Ultra Glass SA ASTM D6163 S I

Flintlastic® Base 20 ASTM D6163 S I

Flintlastic® Base 20 T ASTM D6163 S I

Flintlastic® Ultra Poly SMS Base Sheet ASTM D6164 S I

Cap Membranes (SBS)

Flintlastic® FR Dual Cap ASTM D6162 G I

Flintlastic® SA Cap FR ASTM D6163 G I

Flintlastic® SA Cap FR CoolStar™ ASTM D6163 G I

Flintlastic® Cap 30 ASTM D6163 G I

Flintlastic® Cap 30 CoolStar™ ASTM D6163 G I

Flintlastic® FR Cap 30 ASTM D6163 G I

Flintlastic® FR Cap 30 CoolStar™ ASTM D6163 G I

Flintlastic® FR Cap 30 T ASTM D6163 G I

Flintlastic® FR Cap 30 T CoolStar™ ASTM D6163 G I

Flintlastic® SA Cap ASTM D6164 G I

Flintlastic® SA Cap CoolStar™ ASTM D6164 G I

Flintlastic® FR-P ASTM D6164 G I

Flintlastic® FR-P CoolStar™ ASTM D6164 G I

Flintlastic® GMS ASTM D6164 G I

Flintlastic® GMS CoolStar™ ASTM D6164 G I

Flintlastic® GTS ASTM D6164 G II

Flintlastic® GTS CoolStar™ ASTM D6164 G II

Flintlastic® GTS-FR ASTM D6164 G II

Flintlastic® GTS-FR CoolStar™ ASTM D6164 G II

Flintlastic® Premium FR-P ASTM D6164 G II

Flintlastic® Premium FR-P CoolStar™ ASTM D6164 G II

Flintlastic® Premium GMS ASTM D6164 G II

Flintlastic® Premium GMS CoolStar™ ASTM D6164 G II



5. LIMITATIONS:

5.1 This is a building code evaluation. Neither Trinity|ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose.

5.2 This Evaluation Report is not for use in HVHZ jurisdictions.

5.3 Refer to a current Roofing Materials Directory for fire ratings of this product.

5.4 For steel deck installations, foam plastic insulation shall be separated from the building interior in accordance with FBC 2603.4 unless the exceptions stated in FBC 2603.4.1 and 2603.6 apply.

5.5 The roof system evaluation herein pertains to above-deck roof components. Roof decks shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. Load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation.

5.6 For recover installations, the existing roof shall be examined in accordance with FBC 1510.

5.7 For mechanically attached insulation or membrane or strip-bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter 16. Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29 and Roofing Application Standard RAS 117. Assemblies marked with an asterisk* carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (January 2016) for Zone 2/3 enhancements.

5.8 For assemblies with all components fully bonded in place, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis is permitted for these systems.

5.9 For mechanically attached insulation or membrane over existing roof decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with ANSI/SPRI FX-1 or Testing Application Standard TAS 105.

5.10 For bonded insulation or membrane over existing substrates in a re-roof (tear off) or recover installation, the existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If any surface conditions exist that bring system performance into question, field uplift testing in accordance with ANSI/SPRI IA-1, ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124 shall be conducted on mock-ups of the proposed new roof assembly.

5.11 For bonded insulation or membrane over existing substrates in a recover installation, the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction, as documented through field uplift testing in accordance with ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124.

5.12 Metal edge attachment (except gutters), shall be designed and installed for wind loads in accordance with FBC Chapter 16 and tested for resistance in accordance with ANSI/SPRI ES-1 or RAS 111, except the basic wind speed shall be determined from FBC Figure 1609.

5.13 All products in the roof assembly shall have quality assurance audit in accordance with the FBC and F.A.C. Rule 61G20-3.



6. INSTALLATION:

6.1 Flintlastic® Modified Bitumen Roof Systems shall be installed in accordance with CertainTeed Corporation published installation instructions, subject to the Limitations / Conditions of Use herein.

6.2 System attachment requirements for wind load resistance are set forth in Appendix 1. ”MDP” = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads, and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC 1504.9 has already been applied). Refer to FBC 1609 for determination of design wind loads.

7. BUILDING PERMIT REQUIREMENTS:

As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product.

8. MANUFACTURING PLANTS:

Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 61G20-3 QA requirements.

9. QUALITY ASSURANCE ENTITY:

UL, LLC. – QUA9625; (414) 248-6409, [email protected]

- THE 57-PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT -

Exterior Research and Design, LLC. d/b/a Trinity|ERD Evaluation Report 3520.03.04-R19 for FL2533-R18 Certificate of Authorization #9503 FBC NON-HVHZ EVALUATION Revision 19: 06/06/2017 Prepared by: Robert Nieminen, PE-59166 CertainTeed Corporation; (610) 651-5847 Appendix 1, Page 1 of 57

APPENDIX 1: ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE

Table Deck Application Type Description Page

1A Wood New or Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 5-6

1B Wood New, Reroof (Tear-Off) or Recover B Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 7

1C Wood New, Reroof (Tear-Off) or Recover C Mech. Attached Insulation, Bonded Roof Cover 8-9

1D Wood New, Reroof (Tear-Off) or Recover D Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 10-12

1E-1 Wood New, Reroof (Tear-Off) E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 13-15

1E-2 Wood New, Reroof (Tear-Off) or Recover E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 16-17

1F Wood New or Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 17

2A Steel or Structural Concrete New, Reroof (Tear-Off) or Recover B Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 18-20

2B Steel or Structural Concrete New, Reroof (Tear-Off) or Recover C Mech. Attached Insulation, Bonded Roof Cover 21-25

2C Steel or Structural Concrete New, Reroof (Tear-Off) or Recover D Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 26-28

3A Concrete New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 29-36

3B Concrete New or Reroof (Tear-Off) A-3 Bonded Temp Roof/Vapor Barrier, Bonded Insulation, Bonded Roof Cover 36

3C Concrete New or Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 37

4A LWIC New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 38-39

4B LWIC New or Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 40

4C LWIC New, Reroof (Tear-Off) E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 41-44

5A CWF New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 45

5B CWF New or Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 46

5C CWF New, Reroof (Tear-Off) or Recover C Mech. Attached Insulation, Bonded Roof Cover 46

5D CWF New, Reroof (Tear-Off) E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 47

6A Gypsum Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 48-49

6B Gypsum Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 50

6C Gypsum Reroof (Tear-Off) C Mech. Attached Insulation, Bonded Roof Cover 51

6D Gypsum Reroof (Tear-Off) E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 51

7A Various Recover A-1 Bonded Insulation, Bonded Roof Cover 52-57

7B Various Recover F Non-Insulated, Bonded Roof Cover 57

The following notes apply to the systems outlined herein:

1. The roof system evaluation herein pertains to above-deck roof components. Roof decks shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. Load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation.

2. Unless otherwise noted, fasteners and stress plates for insulation attachment shall be as follows. Fasteners shall be of sufficient length for the following engagements: Wood Deck: OMG #14 Roofgrip with Flat Bottom Plate (Accutrac), OMG HD with OMG 3 in. Galvalume Steel Plate, Dekfast #14 with Hex Plate or 3” Round Insulation Plate, Trufast HD with Trufast 3”

Metal Insulation Plates or FlintFast #14 Fastener with FlintFast 3” Insulation Plates. Minimum 0.75-inch plywood penetration or minimum 1-inch wood plank embedment. Steel Deck: OMG #12 or #14 Roofgrip with Recessed or Flat Bottom Plate (Accutrac), OMG #12 Standard or HD with OMG 3 in. Galvalume Steel Plate, Dekfast #12 or #14 with Hex Plate or 3” Round

Insulation Plate, Trufast DP or HD with Trufast 3” Metal Insulation Plates or FlintFast #12 or #14 Fastener with FlintFast 3” Insulation Plates. Minimum 0.75-inch steel penetration and engage the top flute of the steel deck.

Structural Concrete: OMG #14 Roofgrip with Recessed or Flat Bottom Plate (Accutrac), OMG HD or CD-10 with OMG 3 in. Galvalume Steel Plate, Dekfast #14 or DekSpike with Hex Plate or 3” Round Insulation Plate, Trufast HD or CF with Trufast 3” Metal Insulation Plates or FlintFast #14 Fastener with FlintFast 3” Insulation Plates. Minimum 1-inch embedment. Fasteners installed with a pilot hole in accordance with the fastener manufacturer’s published installation instructions.


3. Unless otherwise noted, insulation may be any one layer or combination of polyisocyanurate, polystyrene, wood fiberboard, perlite, GlasRoc Roof Board or gypsum-based roof board that meets the QA requirements of F.A.C. Rule 61G20-3 and is documented as meeting FBC 1505.1 and, for foam plastic, FBC 2603.4.1 or 2603.8, when installed with the roof cover.

4. Minimum 200 psi, minimum 2-inch lightweight insulating concrete may be substituted for rigid insulation board for System Type D (mechanically attached base sheet, bonded roof cover), whereby the base sheet fasteners are installed through the LWIC to engage the structural steel or structural concrete deck. The structural deck shall be of equal or greater configuration to the steel and structural concrete deck listings.

5. Unless otherwise noted, insulation adhesive application rates are as follows. Ribbon or bead width is at the time of application; the ribbons/beads shall expand as noted in the manufacturer’s published instructions. Hot asphalt (HA): Full coverage at 25-30 lbs/square Ashland Pliodeck (A-PD): Continuous 0.75 inch wide ribbons, 12-inch o.c. Ribbons of subsequent layers shall be perpendicular to those in the layer below. Dow Insta-Stik (D-IS): Continuous 0.75 to 1 inch wide ribbons, 12-inch o.c. Millennium One Step Foamable Adhesive (M-OSFA): Continuous 0.25 to 0.5-inch wide ribbons, 12-inch o.c. Millennium PG-1 Pump Grade Adhesive (M-PG1): Continuous 0.5 to 0.75-inch wide ribbons, 12-inch o.c. OMG OlyBond 500 or OlyBond Green (OB500): Continuous 0.75-inch wide ribbons, 12-inch o.c. (PaceCart or SpotShot) ICP Adhesives CR-20: Continuous 2.5 to 3-inch wide ribbons, 12-inch o.c. Note: When multiple layers(s) of insulation and/or coverboard are installed in ribbon-applied adhesive, adhesive ribbons shall be staggered from layer-to-layer a distance of one-half the ribbon spacing. Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation board shall be not less than one-half the specified ribbons spacing.

6. Unless otherwise noted, all insulations are flat-stock or taper board of the minimum thickness noted. Tapered polyisocyanurate at the following thickness limitations may be substituted with the following Maximum Design Pressure (MDP) limitations. In no case shall these values be used to ‘increase’ the MDP listings in the tables; rather if MDP listing below meets or exceeds that listed for a particular system in the tables, then the thinner board listed below may be used as a drop-in for the equivalent thicker material listed in the table: Ashland Pliodeck (A-PD) @ 12-inch o.c. MDP -105.0 psf (Min. 1.0-inch) Ashland Pliodeck (A-PD) @ 6-inch o.c. MDP -277.5 psf (Min. 1.0-inch) Dow Insta-Stik (D-IS): MDP -120.0 psf (Min. 1.0-inch) Millennium One Step Foamable Adhesive (M-OSFA): MDP -157.5 psf (Min. 1.0-inch) Millennium PG-1 Pump Grade Adhesive (M-PG1): MDP -157.5 psf (Min. 1.0-inch) OMG OlyBond 500 (OB500): MDP -45.0 psf (Min. 0.5-inch Multi-Max FA3) OMG OlyBond 500 (OB500): MDP -187.5 psf (Min. 0.5-inch ISO 95+ GL) OMG OlyBond 500 (OB500): MDP -315.0 psf (Min. 0.5-inch ENRGY 3) OMG OlyBond 500 (OB500): MDP -487.5 psf (Min. 0.5-inch ACFoam II) ICP Adhesives CR-20: MDP -117.5 psf (Min. 1.0-inch)

7. Bonded polyisocyanurate insulation boards shall be maximum 4 x 4 ft.

8. For mechanically attached components or partially bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter 16, and Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29 and Roofing Application Standard RAS 117. Assemblies marked with an asterisk* carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (January 2016) for Zone 2/3 enhancements.

9. For assemblies with all components fully bonded in place, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16, and no rational analysis is permitted.

10. For mechanically attached components over existing decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with ANSI/SPRI FX-1 or Testing Application Standard TAS 105.

11. For existing substrates in a bonded recover or re-roof installation, the existing roof surface or existing roof deck shall be examined for compatibility and bond performance with the selected adhesive, and the existing roof system (for recover) shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction, as documented through field uplift testing in accordance with ANSI/SPRI IA-1, ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124.

12. For Concrete Deck or Recover Applications using System Type D, the insulation is optional.


13. Lightweight Insulating Concrete (LWC) shall be cast in accordance with FBC Section 1917 to the satisfaction of the Authority Having Jurisdiction. For systems where specific LWC is referenced, refer to current LWC Product Approval for specific deck construction and limitations. For systems where specific LWC is not referenced, the minimum design mix shall be 300 psi. In all cases, the minimum top-coat thickness is 2-inches. For LWC over structural concrete, reference is made to FBC Section 1917.4.1, Point 1

14. Unless otherwise noted, refer to the following references for bonded base, ply or cap sheet applications.

CERTAINTEED FLINTLASTIC® MODIFIED BITUMEN COMPONENTS & APPLICATION METHODS

Reference Layer Material Application

BP-AA (Base and Ply sheets, Asphalt-Applied)

Base Glasbase; All Weather/Empire Base; Flexiglas Base; Flintlastic Base 20 Hot asphalt at 20-40 lbs/square

Ply One or more Flintglas Ply 4; Flintglas Premium Ply 6

BP-AA2 (Base, Spot-Asphalt-Applied)

Base Yosemite Venting Base Hot asphalt in 24-inch diameter spots in 30-inch grid pattern

BP-AA3 (Base, Spot-Asphalt-Applied)

Base Yosemite Venting Base Hot asphalt in 9-inch diameter spots in grid pattern noted herein.

BP-AA4 (Base, Strip-Asphalt-Applied)

Base Yosemite Venting Base Hot asphalt in 9-inch wide ribbons spaced as noted herein.

BP-CA2 Base/Ply Glasbase; All Weather/Empire Base; Flexiglas Base; Flintlastic Base 20 Henry #903 Adhesive at 1.5 gal/square

BP-CA3 Base/Ply Glasbase; All Weather/Empire Base; Flexiglas Base; Flintlastic Base 20 Millennium Hurricane Force Membrane

Adhesive, beads spaced 6-inch o.c.

SBS-AA (SBS, Asphalt-Applied)

Base Flintlastic Base 20; Flintlastic Poly SMS Base; Flintlastic Ultra Poly SMS Base

Hot asphalt at 20-40 lbs/square Ply One or more Flintlastic Base 20; Flintlastic Poly SMS Base; Flintlastic Ultra Poly SMS Base

Cap Flintlastic Cap 30; Flintlastic Cap 30 CoolStar; Flintlastic FR Cap 30; Flintlastic FR Cap 30 CoolStar; Flintlastic FR Dual Cap; Flintlastic FR-P; Flintlastic FR-P CoolStar; Flintlastic Premium FR-P; Flintlastic Premium FR-P CoolStar; Flintlastic GMS; Flintlastic GMS CoolStar; Flintlastic Premium GMS; Flintlastic Premium GMS CoolStar

SBS-CA1 (SBS, Cold-Applied)


FlintBond Brush or Karnak No. 81 Cold Process Modified Bitumen Adhesive Brush Grade at 1 gal/square

Note: Base ply cures overnight prior to application of the ply or cap ply.

Ply Flintlastic Base 20; Flintlastic Poly SMS Base; Flintlastic Ultra Poly SMS Base

Cap Flintlastic FR Cap 30; Flintlastic FR Cap 30 CoolStar; Flintlastic FR Dual Cap; Flintlastic FR-P; Flintlastic FR-P CoolStar; Flintlastic Premium FR-P; Flintlastic Premium FR-P CoolStar; Flintlastic GMS; Flintlastic GMS CoolStar; Flintlastic Premium GMS; Flintlastic Premium GMS CoolStar



Henry #903 Adhesive at 1.5 gal/square. Ply Flintlastic Base 20; Flintlastic Poly SMS Base; Flintlastic Ultra Poly SMS Base




Millennium Hurricane Force Membrane Adhesive, beads spaced 6-inch o.c.

Ply Flintlastic Base 20; Flintlastic Poly SMS Base; Flintlastic Ultra Poly SMS Base



CERTAINTEED FLINTLASTIC® MODIFIED BITUMEN COMPONENTS & APPLICATION METHODS (CONTINUED)

Reference Layer Material Application

SBS-TA (SBS, Torch-Applied)

Base Flintlastic Ultra Poly SMS Base; Flintlastic Base 20 T

Torch-Applied Ply One or more Flintlastic Ultra Poly SMS Base; Flintlastic Base 20 T

Cap Flintlastic FR Cap 30 T; Flintlastic FR Cap 30 T CoolStar; Flintlastic GTS; Flintlastic GTS CoolStar; Flintlastic GTS-FR; Flintlastic GTS-FR CoolStar; FlintClad

APP-TA (APP, Torch-Applied)

Base One or more Flintlastic APP Base T; Flintlastic STA; Flintlastic STA Plus

Torch-Applied Cap Flintlastic STA; Flintlastic STA Plus; Flintlastic GTA; Flintlastic GTA CoolStar; Flintlastic GTA-FR; Flintlastic GTA-FR CoolStar

SBS-SA-H (SBS, Self-Adhering, Hybrid Systems)

Base/Ply Black Diamond Base Sheet; Flintlastic Ultra Glass SA Self-Adhering

SBS-SA (SBS, Self-Adhering)

Base Flintlastic SA PlyBase; Flintlastic SA Mid Ply

Self-Adhering Ply Flintlastic SA PlyBase; Flintlastic SA Mid Ply

Cap Flintlastic SA Cap; Flintlastic SA Cap CoolStar; Flintlastic SA Cap FR; Flintlastic SA Cap FR CoolStar

15. ”MDP” = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to FBC 1609 for determination of design wind loads.


TABLE 1A: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)

SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER

Sys. No.

Deck

(Note 1)

Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 14) MDP (psf) Type Fasteners Attach Type Attach Type Attach Base Ply Cap

SELF-ADHERING SYSTEMS:

W-1

Min. 19/32-inch plywood at max. 24-inch spans

Glasbase, All Weather Empire, Flexiglas Base, Flintlastic Base 20; Poly SMS; Ultra Poly SMS; Yosemite

32 ga., 1-5/8-inch dia. tin caps with 11 ga. annular ring shank nails

9-inch o.c. in 4-inch lap and 12-inch o.c. in two (2), equally spaced, staggered center rows

Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY-3, H-Shield or Multi-Max FA3

HA

Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA

HA SBS-SA (Optional) SBS-SA

SBS-SA -45.0*

W-2


Glasbase, All Weather Empire, Flexiglas Base, Poly SMS or Ultra Poly SMS


8-inch o.c. in 3-inch lap and 8-inch o.c. in three (3), equally spaced, staggered center rows


HA full coverage or OB500, M-OSFA, A-PD, D-IS or CR-20, 4-inch o.c.



SBS-SA (Optional) SBS-SA

SBS-SA -52.5

W-3


Yosemite Venting Base Sheet




HA



SBS-SA -52.5

W-4





(Optional) Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY-3, H-Shield or Multi-Max FA3


Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board primed with FlintPrime or FlintPrime SA


SBS-SA (Optional) SBS-SA

SBS-SA -60.0

W-5






HA

Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board primed with FlintPrime or FlintPrime SA


SBS-SA -60.0

HYBRID SYSTEMS:

W-6






HA None N/A SBS-SA-H

(Optional) BP-AA, SBS-AA, SBS-TA or APP-TA

SBS-AA, SBS-TA or APP-TA

-45.0*


TABLE 1A: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)


Sys. No.

Deck

(Note 1)


W-7

Min. 19/32-inch plywood at max. 24-inch

Glasbase; Flintglas Premium Ply 6; Yosemite







-60.0

CONVENTIONAL SYSTEMS:

W-8






HA

Min. 0.25-inch Dens Deck primed with FlintPrime (ASTM D41) primer

HA

BP-AA, SBS-AA, SBS-TA or APP-TA



-45.0*

W-9












-52.5

W-10






HA


HA




-52.5

W-11







Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board





-60.0

W-12






HA


HA




-60.0


TABLE 1B: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER

SYSTEM TYPE B: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER

System No.

Deck

(Note 1)

Base Insulation Layer Top Insulation Layer Roof Cover (Note 14) MDP (psf)

Type Fasteners Attach Type Attach Base Ply Cap

HYBRID SYSTEMS:

W-13

Min. 15/32-inch exterior grade plywood at max. 24-inch spans

Min. 1.5-inch ACFoam II, FlintBoard ISO, H-Shield or FlintBoard ISOH.

FlintFast #12 or #14 with FlintFast 3” Insulation Plates

1 per 1.33 ft2


HA, D-IS, M-OSFA, M-PG1 or OB500

SBS-SA-H (Optional) APP-TA APP-TA -67.5


W-14


Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY 3, H-Shield

Note 2 1 per 2 ft2

Min. 0.5-inch FM Approved Wood Fiberboard, min. 0.75-inch FM Approved perlite

HA BP-AA or SBS-AA



-45.0*

W-15


Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY 3, H-Shield

Note 2 1 per 2 ft2

Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board, Dens Deck or Dens Deck Prime

HA BP-AA, SBS-AA, SBS-TA or APP-TA



-45.0*

W-16




1 per 1.33 ft2

Optional additional layer(s) of base insulation followed by Min. 0.25-inch SECUROCK Gypsum-Fiber Roof board


APP-TA (Optional) APP-TA APP-TA -90.0


TABLE 1C: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER

SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER

System No.

Deck

(Note 1) Base Insulation Layer

Top Insulation Layer Roof Cover (Note 14) MDP (psf) Type Fasteners Attach Base Ply Cap


W-17 Min. 15/32-inch plywood at max. 24-inch spans

(Optional) One or more layers, any combination, loose laid


Flintfast 3 in. Insulation Plates with FlintFast #12 or #14

1 per 3.2 ft2 SBS-SA (Optional) SBS-SA

SBS-SA -30.0*

W-18 Min. 19/32-inch exterior grade plywood at max. 24-inch spans


Min. 0.25-inch Dens Deck Note 2 1 per 1.33 ft2

Apply FlintPrime or FlintPrime SA to board & plates, followed by SBS-SA

(Optional) SBS-SA

SBS-SA -45.0



Min. 3/8-inch SECUROCK Gypsum-Fiber Roof Board


1 per 2.7 ft2 SBS-SA (Optional) SBS-SA

SBS-SA -45.0*



Min. 1.5-inch ACFoam II, ENRGY 3, H-Shield, Multi-Max FA3 or FlintBoard ISO


1 per 2 ft2


(Optional) SBS-SA

SBS-SA -45.0*



Min. 1.5-inch FlintBoard ISO

FlintFast #14 HD with FlintFast 3” Insulation Plates or Trufast HD with Trufast 3” Metal Insulation Plates

1 per 1.6 ft2 Apply FlintPrime to board & plates, followed by SBS-SA

(Optional) SBS-SA

SBS-SA -52.5



Min. 1.5-inch ACFoam II, ENRGY 3, H-Shield, Multi-Max FA3 or FlintBoard ISO

Note 2 1 per 1.45 ft2


(Optional) SBS-SA

SBS-SA -60.0

HYBRID SYSTEMS:



Min. 0.25-inch Dens Deck; Dens Deck Prime


1 per 2 ft2 SBS-SA-H (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-30.0*





1 per 1.6 ft2 SBS-SA-H (Optional) SBS-TA or APP-TA

SBS-TA or APP-TA

-52.5



Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY 3 or Multi-Max FA3

Note 2 1 per 1.33 ft2 SBS-SA-H (Optional) BP-AA or SBS-AA

SBS-AA -52.5



Min. 1.5-inch ACFoam II, FlintBoard ISO, H-Shield, FlintBoard ISOH

Note 2 1 per 1.45 ft2 SBS-SA-H (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-60.0


TABLE 1C: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER


System No.

Deck

(Note 1) Base Insulation Layer



(Optional) Min. 1.5-inch, One or more layers, any combination, loose laid



1 per 1.33 ft2 SBS-SA-H (Optional) SBS-AA, SBS-TA or APP-TA


-75.0




Note 2 1 per 1.33 ft2 SBS-SA-H (Optional) SBS-TA or APP-TA

SBS-TA or APP-TA

-82.5





Note 2 1 per 2 ft2 BP-AA or SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-45.0*



Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board, Dens Deck or Dens Deck Prime

FlintFast #12 or #14 HD with FlintFast 3” Insulation Plates

1 per 2 ft2 BP-AA, SBS-AA, SBS-TA or APP-TA



-45.0*


(Optional for Recover) Min. 1.5-inch, One or more layers, any combination, loose laid



1 per 1.45 ft2 APP-TA (Optional) APP-TA

APP-TA -60.0


(Optional for Concrete or Recover) Min. 2-inch ACFoam II, FlintBoard, H-Shield or ENRGY 3, loose laid.



1 per 1.78 ft2 BP-AA, SBS-AA, SBS-TA or APP-TA



-60.0


(Optional for Recover) Min. 1.5-inch, One or more layers, any combination, loose laid



1 per 1.33 ft2 APP-TA (Optional) APP-TA

APP-TA -67.5


TABLE 1D: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER

SYSTEM TYPE D: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER

System No.

Deck

(Note 1)

Insulation Layer(s) Base or Anchor Sheet Roof Cover (Note 14) MDP (psf) Type Attach Base Fasteners Attach Ply Cap


W-34 Min. 19/32-inch plywood at max 24-inch spans

Min. 1.5-inch, One or more layers, any combination

Prelim. Attach

Flintlastic SA NailBase Note 2

8-inch o.c. at min. 3-inch lap and 8-inch o.c. in two (2), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA

(Optional) SBS-SA

SBS-SA -82.5*



Prelim. Attach

Flintlastic SA NailBase

Flintfast 3 in. Insulation Plates with FlintFast #12 or #14; Trufast 3” Metal Insulation Plates with DP or HD; OMG 3 in. Round Metal Plates with OMG #14 HD

6-inch o.c. at min. 2-inch lap and 6-inch o.c. in three (3), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA.

(Optional) SBS-SA

SBS-SA -97.5*



Prelim. Attach



6-inch o.c. at min. 2-inch lap and 6-inch o.c. in four (4), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA.

(Optional) SBS-SA

SBS-SA -127.5*

HYBRID SYSTEMS:



Prelim. Attach

Glasbase; Flexiglas; Flintlastic Base 20; Poly SMS Base; Ultra Poly SMS Base


6-inch o.c. at 4-inch lap and 6-inch o.c. in three (3), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA.

SBS-SA-H SBS-AA, SBS-TA or APP-TA

-97.5



Prelim. Attach


Note 2 7-inch o.c. at 3-inch lap and 7-inch o.c. in three (3), equally spaced, staggered center rows


-105.0



Prelim. Attach



6-inch o.c. at 4-inch lap and 6-inch o.c. in four (4), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA.


-127.5





System No.

Deck

(Note 1)


W-40



Prelim. Attach

Glasbase; All Weather/Empire Base; Flexiglas Base; Flintlastic Base 20; Yosemite

Note 2 12-inch o.c. at 4-inch lap and 36-inch o.c. in two (2), equally spaced, staggered center rows



-30.0*

W-41



Prelim. Attach





-45.0*

W-42



Prelim. Attach

Poly SMS Base; Ultra Poly SMS Base




-45.0*



Prelim. Attach

Glasbase; Flexiglas; Flintlastic Base 20; All Weather / Empire Base; Poly SMS Base; Ultra Poly SMS Base; Yosemite


6-inch o.c. at 4-inch lap and 6-inch o.c. in three (3), equally spaced, staggered center rows.



-97.5



Prelim. Attach

Flintlastic APP Base T OMG 3 in. Round Metal Plates with OMG #14 HD


APP-TA APP-TA -97.5


One or more layers, any thickness or combination

Prelim. Attach


Flintfast 3 in. Insulation Plates with FlintFast #14; Trufast 3" Metal Insulation Plates with Trufast HD

8-inch o.c. at 4-inch lap and 8-inch o.c. at three (3) equally spaced, staggered center rows


SBS-AA, SBS-TA or APP_TA

-97.5



Prelim. Attach

Glasbase; Flexiglas; Flintlastic Base 20; Poly SMS Base; Ultra Poly SMS Base; Yosemite




-105.0



Prelim. Attach

Flintlastic APP Base T OMG 3 in. Round Metal Plates with OMG #14 HD or Dekfast Hex Plate with Dekfast #14

7-inch o.c. at 3-inch lap and 7-inch o.c. in three (3), equally spaced, staggered center rows

APP-TA APP-TA -105.0



Prelim. Attach



6-inch o.c. at 4-inch lap and 6-inch o.c. in four (4), equally spaced, staggered center rows.



-127.5




System No.

Deck

(Note 1)




Prelim. Attach




COLD-APPLIED SYSTEMS:


Min. 1-inch, One or more layers, any combination

Loose-laid

Glasbase; Flexiglas Base; Flintlastic Base 20; All Weather / Empire Base; Yosemite Venting Base; Flintlastic Poly SMS Base; Flintlastic Ultra Poly SMS Base

Flintfast 3 in. Insulation Plates with FlintFast #12 or #14; Trufast 3” Metal Insulation Plates with DP or HD


(Optional) SBS-CA1

SBS-CA1 -52.5


TABLE 1E-1: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)

SYSTEM TYPE E: NON-INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER

System No.

Deck

(Note 1)

Base Sheet Roof Cover (Note 14) MDP (psf) Base Fasteners Attach Ply Cap



Flintlastic SA NailBase Simplex MAXX Cap

9-inch o.c. at min. 3-inch lap and 12-inch o.c. in two (2), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer.

(Optional) SBS-SA

SBS-SA -45.0*


Flintlastic SA NailBase Min. 1-inch long, 12 ga. Simplex Metal Cap Nails

6-inch o.c. at min. 2-inch lap and 6-inch o.c. in four (4), equally spaced, staggered center rows

(Optional) SBS-SA

SBS-SA -52.5


Flintlastic SA NailBase 32 ga., 1-5/8-inch dia. tin caps with 11 ga. annular ring shank nails

8-inch o.c. at min. 2-inch lap and 8-inch o.c. in three (3), equally spaced, staggered center rows

(Optional) SBS-SA

SBS-SA -52.5



8-inch o.c. at min. 2-inch lap and 8-inch o.c. in three (3), equally spaced, staggered center rows

(Optional) SBS-SA

SBS-SA -60.0


Flintlastic SA NailBase Simplex MAXX Cap

8-inch o.c. at min. 3-inch lap and 8-inch o.c. in three (3), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer.

(Optional) SBS-SA

SBS-SA -67.5




(Optional) SBS-SA

SBS-SA -75.0



Cap nails: 1-inch diameter, 0.032-inch thick metal cap with 0.120" shank diameter, annular ring shank nails

7-inch o.c. at min. 4-inch laps and 7-inch o.c. in five (5), equally spaced, staggered center rows

(Optional) SBS-SA

SBS-SA -75.0




(Optional) SBS-SA

SBS-SA -105.0

HYBRID SYSTEMS:


Glasbase; Flexiglas; Flintlastic Base 20; All Weather / Empire Base; Poly SMS Base; Ultra Poly SMS Base


9-inch o.c. at 4-inch lap and 12-inch o.c. in two (2), equally spaced, staggered center rows


-45.0*


Glasbase; Flexiglas; Flintlastic Base 20; All Weather / Empire Base; Poly SMS Base; Ultra Poly SMS Base

Min. 1-inch long, 12 ga. Simplex Metal Cap Nails

6-inch o.c. at 3-inch lap and 6-inch o.c. in four (4), equally spaced, staggered center rows


-52.5




System No.

Deck

(Note 1)







-52.5






-60.0






-82.5






-105.0








-45.0*


Glasbase; Flexiglas; Flintlastic Base 20; All Weather / Empire Base; Poly SMS Base; Yosemite

Simplex MAXX Cap 9-inch o.c. at 2-inch lap and 18-inch o.c. in two (2), equally spaced, staggered center rows



-45.0*


Flintlastic APP Base T Simplex MAXX Cap 9-inch o.c. at 2-inch lap and 18-inch o.c. in two (2), equally spaced, staggered center rows

(Optional) APP-TA

APP-TA -45.0*



Min. 1-inch long, 12 ga. Simplex Metal Cap Nails




-52.5







-52.5






-52.5



(Optional) APP-TA

APP-TA -52.5







-60.0




System No.

Deck

(Note 1)




Cap nails: 1-inch diameter, 0.032-inch thick metal cap with 0.120-inch shank diameter, annular ring shank nails.

6-inch o.c. at 4-inch lap and 6-inch o.c. at five (5) equally spaced, staggered center rows

(Optional) BP-AA, SBS-AA or SBS-TA

SBS-AA or SBS-TA

-67.5







-82.5






-90.0



(Optional) APP-TA

APP-TA -90.0







-105.0



Simplex MAXX Cap 6-inch o.c. at 2-inch lap and 6-inch o.c. in three (3), equally spaced, staggered center rows



-105.0


Flintlastic APP Base T Simplex MAXX Cap 6-inch o.c. at 2-inch lap and 6-inch o.c. in three (3), equally spaced, staggered center rows

(Optional) APP-TA

APP-TA -105.0


TABLE 1E-2: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER


System No.

Deck

(Note 1)




Flintlastic SA NailBase Note 2

8-inch o.c. at min. 3-inch lap and 8-inch o.c. in two (2), equally spaced, staggered center rows. Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA

(Optional) SBS-SA

SBS-SA -82.5*




6-inch o.c. at min. 2-inch lap and 6-inch o.c. in three (3), equally spaced, staggered center rows. Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA.

(Optional) SBS-SA

SBS-SA -97.5*




6-inch o.c. at min. 2-inch lap and 6-inch o.c. in four (4), equally spaced, staggered center rows. Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA.

(Optional) SBS-SA

SBS-SA -127.5*

HYBRID SYSTEMS:




6-inch o.c. at 4-inch lap and 6-inch o.c. in three (3), equally spaced, staggered center rows. Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA.


-97.5





-105.0




6-inch o.c. at 4-inch lap and 6-inch o.c. in four (4), equally spaced, staggered center rows. Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA.


-127.5







-30.0*






-45.0*






-45.0*


TABLE 1E-2: WOOD DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER


System No.

Deck

(Note 1)








-97.5




APP-TA APP-TA -97.5






SBS-AA or SBS-TA

-97.5






-105.0


Flintlastic APP Base T OMG 3 in. Round Metal Plates with OMG #14 HD or Dekfast Hex Plate with Dekfast #14









-127.5








Flintfast 3 in. Insulation Plates with FlintFast #12 or #14; Trufast 3” Metal Insulation Plates with DP or HD


(Optional) SBS-CA1

SBS-CA1 -52.5

TABLE 1F: WOOD DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)

SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER

System No.

Deck

(Note 1) Primer

Roof Cover (Note 14) MDP (psf)

Base Ply Cap

W-97 Min. 15/32-inch plywood at max 24-inch spans FlintPrime or FlintPrime SA SBS-SA-H (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -112.5

W-98 Min. 15/32-inch plywood at max 24-inch spans FlintPrime or FlintPrime SA SBS-SA (Optional) SBS-SA SBS-SA -127.5


TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER


System No.

Deck

(Note 1)

Base Insulation Layer Top Insulation Layer Roof Cover (Note 14) MDP (psf) Type Fasteners Attach Type Attach Base Ply Cap


S-1 Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structrual concrete

Min. 2-inch ACFoam II, FlintBoard, ENRGY 3 or H-Shield

Note 2 1 per 4

ft2 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

HA, D-IS, M-OSFA, OB500 or CR-20

SBS-SA (Optional) SBS-SA SBS-SA -37.5*


Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or H-Shield

Note 2 1 per 2



SBS-SA (Optional) SBS-SA SBS-SA -45.0*

HYBRID SYSTEMS:



Note 2 1 per

1.45 ft2 Additional layer(s) base insulation


Flintlastic Ultra Glass SA

(Optional) SBS-AA, SBS-TA, APP-TA

SBS-AA, SBS-TA, APP-TA

-37.5



Note 2 1 per

1.45 ft2 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board


Flintlastic Ultra Glass SA



-52.5




1 per 1.45 ft2



SBS-SA-H (Optional) APP-TA APP-TA -67.5


Min. 1.5-inch ACFoam II, FlintBoard ISO, H-Shield or FlintBoard ISOH

FlintFast #12 (steel only) or #14 HD with FlintFast 3” Insulation Plates or Trufast #12 (steel only) or HD with Trufast 3” Metal Insulation Plates

1 per 1.6 ft2


D-IS, M-OSFA, M-PG1 or OB500

SBS-SA-H (Optional) SBS-TA or APP-TA

SBS-TA or APP-TA

-75.0


Min. 1.5-inch ENRGY 3


1 per 1 ft2


OB500, 4-inch o.c.

SBS-SA-H (Optional) SBS-TA or APP-TA

SBS-TA or APP-TA

-90.0*




Note 2 1 per 4






-37.5*



Note 2 1 per 2

ft2

Min. 0.5-inch FM Approved Wood Fiberboard, min. 0.75-inch FM Approved perlite.

HA BP-AA or SBS-AA



-45.0*




System No.

Deck

(Note 1)




Note 2 1 per 2

ft2 Min. 0.25-inch Dens Deck or Dens Deck Prime

HA




-45.0*



Note 2 1 per 2






-45.0*



Note 2 1 per 3.2

ft2

Min. 0.5-inch FM Approved Wood Fiberboard, min. 0.75-inch FM Approved perlite.

HA BP-AA or SBS-AA



-45.0*



Note 2 1 per 3.2

ft2 Min. 0.25-inch Dens Deck or Dens Deck Prime

HA




-45.0*


Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or Mult-Max FA3

Note 2 1 per

1.33 ft2 Min. 0.75-inch FescoBoard (homogeneous)

HA BP-AA or SBS-AA



-52.5



Note 2 1 per 1.6






-60.0


Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or Mult-Max FA3

Note 2 1 per

1.33 ft2 Min. 0.5-inch Structodek High Density Fiberboard

HA BP-AA or SBS-AA



-67.5




1 per 1.6 ft2






-75.0




1 per 1 ft2


OB500, 4-inch o.c.




-90.0*





System No.

Deck

(Note 1)



Min. 2-inch ACFoam II, FlintBoard ISO, H-Shield or FlintBoard ISOH


1 per 2 ft2

Min. 1.5-inch ACFoam III, FlintBoard Iso Cold, H-Shield CG or FlintBoard Iso ColdH

OB500 or CR-20

SBS-CA1 None SBS-CA1 -45.0*


Min. 2-inch ACFoam II, FlintBoard ISO, H-Shield or FlintBoard ISOH


1 per 2 ft2

Optional min. 1.5-inch additional layer(s) base insulation, followed by min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

D-IS, M-OSFA, M-PG1, OB500 or CR-20





1 per 1.6 ft2



SBS-CA1 None SBS-CA1 -75.0




1 per 1 ft2


OB500, 4-inch o.c.



TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER


System No.

Deck

(Note 1) Base Insulation Layer(s)






Note 2 1 per 3.2 ft2 SBS-SA (Optional) SBS-SA SBS-SA -30.0*





1 per 2.7 ft2 SBS-SA (Optional) SBS-SA SBS-SA -37.5*




Note 2 1 per 2.7 ft2 SBS-SA (Optional) SBS-SA SBS-SA -45.0*



Min. 0.25-inch Dens Deck

Note 2 1 per 1.33 ft2


(Optional) SBS-SA SBS-SA -45.0













HYBRID SYSTEMS:



Min. 0.25-inch Dens Deck; Dens Deck Prime

Note 2 1 per 2 ft2 SBS-SA-H (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-30.0*





1 per 2.7 ft2 SBS-SA-H (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-37.5*





1 per 2.7 ft2 SBS-SA-H (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-45.0*




System No.

Deck






Note 2 1 per 1.33 ft2 SBS-SA-H (Optional) BP-AA or SBS-AA

SBS-AA -52.5






SBS-TA or APP-TA

-67.5




FlintFast #12 (steel only) or #14 HD with FlintFast 3” Insulation Plates

1 per 1.45 ft2 SBS-SA-H (Optional) SBS-AA, SBS-TA or APP-TA


-75.0






SBS-TA or APP-TA

-82.5






SBS-TA or APP-TA

-82.5




Note 2 1 per 1.33 ft2 SBS-SA-H (Optional) SBS-TA or APP-TA

SBS-TA or APP-TA

-82.5





1 per 1 ft2 SBS-SA-H (Optional) SBS-TA or APP-TA

SBS-TA or APP-TA

-135.0




Min. 0.75-inch FM Approved perlite

Note 2 1 per 2.67 ft2 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-30.0*



Min. 0.5-inch FM Approved high density wood fiberboard

Note 2 1 per 4 ft2 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-37.5*




System No.

Deck






Note 2 1 per 4 ft2 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-37.5*



Min. 2-inch ACFoam II, FlintBoard or ENRGY 3

Note 2 1 per 1.6 ft2 BP-AA2 (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-37.5*




Note 2 1 per 4 ft2 BP-AA, SBS-AA, SBS-TA or APP-TA



-45.0*




Note 2 1 per 2 ft2 BP-AA or SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-45.0*



Min. 0.25-inch Dens Deck or Dens Deck Prime

Note 2 1 per 2 ft2 BP-AA, SBS-AA, SBS-TA or APP-TA



-45.0*



Min. 1-inch FescoBoard (homogeneous) or min. 1.5-inch FescoBoard (laminated)

Note 2 1 per 1.6 ft2 BP-AA2 (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-45.0*



Min. 0.5-inch Structodek, Structodek HD, GP HD Roof Fiberboard or Temple HD1 or HD6

Note 2 1 per 2 ft2 BP-AA2 (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA


-45.0*



Min. 1.5-inch ACFoam II, FlintBoard

Note 2 1 per 1.45 ft2 BP-AA3, 24-inch grid

(Optional) BP-AA or SBS-AA

SBS-AA -52.5



Min. 1.5-inch ACFoam II, FlintBoard

Note 2 1 per 1.45 ft2 BP-AA3, 24-inch grid

BP-AA or SBS-AA SBS-TA -52.5


(Optional for Concrete or Recover) Min. 1.5-inch, One or more layers, any combination, loose laid


FlintFast #12 (steel only) or #14 HD with FlintFast 3” Insulation Plates

1 per 1.45 ft2 APP-TA (Optional) APP-TA APP-TA -60.0




System No.

Deck




(Optional for Concrete or Recover) Min. 2-inch ACFoam II, FlintBoard, H-Shield or ENRGY 3, loose laid.


Note 2 1 per 1.78 ft2 BP-AA, SBS-AA, SBS-TA or APP-TA



-60.0








-82.5


(Optional for Concrete or Recover) Min. 1.5-inch ACFoam II, FlintBoard, H-Shield

Min. 0.5-inch Dens Deck Prime

Trufast HD with Trufast 3” Metal Insulation Plates or FlintFast #14 with FlintFast 3” Insulation Plates

1 per 1.33 ft2 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA

SBS-AA -112.5








-135.0





1 per 1.33 ft2 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA

SBS-AA -157.5



Min. 0.5-inch Dens Deck Prime


1 per 1 ft2 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA

SBS-AA -157.5





1 per 1 ft2 BP-AA, SBS-AA (Optional) BP-AA, SBS-AA

SBS-AA -172.5






1 per 2.7 ft2 SBS-CA1 None SBS-CA1 -37.5*




System No.

Deck







1 per 2 ft2 SBS-CA1 None SBS-CA1 -45.0*












TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER

SYSTEM TYPE D: INSULATED, MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER NOTE: INSULATION OPTIONAL FOR RECOVER OR CONCRETE DECK APPLICATIONS (NOTE 14)

System No.

Deck

(Note 1)





Prelim. Attached

Flintlastic SA NailBase Note 2 9-inch o.c. at min. 2-inch lap and 18-inch o.c. in two (2), equally spaced, staggered center rows

(Optional) SBS-SA

SBS-SA -45.0*



Prelim. Attached


(Optional) SBS-SA

SBS-SA -52.5*



Prelim. Attached


(Optional) SBS-SA

SBS-SA -60.0*



Prelim. Attached

Flintlastic SA NailBase (laid parallel to deck flutes)

Note 2 8-inch o.c. at min. 4-inch lap and 8-inch o.c. in two (2), equally spaced, staggered center rows

(Optional) SBS-SA

SBS-SA -82.5*




Prelim. Attached





-30.0*



Prelim. Attached





-45.0*



Prelim. Attached





-45.0*



Prelim. Attached


Note 2 18-inch o.c. at 4-inch lap and 18-inch o.c. in one (1) staggered center row



-45.0*



Prelim. Attached


Dekfast IF-2-SB plates with #14 Dekfast

12-inch o.c. within the min. 4-inch wide, heat-welded side lap



-45.0*



Prelim. Attached

Glasbase; Flexiglas Base; Flintlastic Base 20; All Weather / Empire Base; Poly SMS Base; Yosemite




-52.5




System No.

Deck

(Note 1)


S-72 Min. 22 ga., type B, 40 ksi steel or min. 2,500 psi structrual concrete


Prelim. Attached

Ultra Poly SMS Base

Trufast 2” Barbed Metal Seam Plates with Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only)


(Optional) SBS-TA or APP-TA

SBS-TA or APP-TA

-52.5



Prelim. Attached

Ultra Poly SMS Base

Trufast 2.4” Barbed Metal Seam Plates with Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only)



SBS-TA or APP-TA

-60.0



Prelim. Attached

Ultra Poly SMS Base

Trufast 2.4” Scoop Seam Plates with Trufast #15 EHD (steel only) or Trufast #14 HD (concrete only)



SBS-TA or APP-TA

-67.5



Prelim. Attached

Glasbase; Yosemite OMG Flat Bottom Plates with OMG #14 HD (Accutrac)




-67.5



Prelim. Attached

Flexiglas Base; Flintlastic Base 20; Yosemite




-67.5



Prelim. Attach





SBS-AA or SBS-TA

-97.5



Prelim. Attached

Ultra Poly SMS Base




SBS-TA or APP-TA

-112.5



Prelim. Attached



SBS-TA or APP-TA

SBS-TA or APP-TA

-112.5



Prelim. Attached



SBS-AA SBS-AA or SBS-TA

-120.0




System No.

Deck

(Note 1)




Prelim. Attached

Ultra Poly SMS Base


6-inch o.c. within the min. 4-inch wide, heat-welded side laps and 6-inch o.c. in one (1) center row, stripped-in with 6-inch side strips of torch-applied Poly SMS Base or Ultra Poly SMS Base.


SBS-TA or APP-TA

-165.0




Prelim. Attached

Glasbase; All Weather/Empire Base; Flexiglas Base; Flintlastic Base 20


SBS-CA1 SBS-CA1 -45.0*



Loose-laid




(Optional) SBS-CA1

SBS-CA1 -75.0


TABLE 3A: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)

SYSTEM TYPE A-1: BONDED INSULATION, BONDED ROOF COVER

Sys. No.

Deck (Note 1)

Primer Base Insulation Layer Top Insulation Layer Roof Cover (Note 14) MDP

(psf) Type Attach Type Attach Base Ply Cap


C-1. Structural concrete

FlintPrime (ASTM D41)


HA Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

HA SBS-SA (Optional) SBS-SA SBS-SA -172.5



Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or Multi-Max FA3

HA Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA



None Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or Multi-Max FA3

A-PD Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA

A-PD SBS-SA (Optional) SBS-SA SBS-SA -105.0


None Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or H-Shield

A-PD Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

A-PD SBS-SA (Optional) SBS-SA SBS-SA -172.5


None Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or Multi-Max FA3

A-PD

6-inch o.c.


A-PD

6-inch o.c. SBS-SA (Optional) SBS-SA SBS-SA -192.5


(Optional) FlintPrime (ASTM D41)

Min. 1.5-inch Multi-Max FA D-IS Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA

D-IS SBS-SA (Optional) SBS-SA SBS-SA -67.5



Min. 1.5-inch ENRGY 3 D-IS Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA




Min. 1.5-inch ACFoam II or FlintBoard D-IS Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA




D-IS Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board




M-OSFA or M-PG1


M-OSFA or M-PG1

SBS-SA (Optional) SBS-SA SBS-SA -172.5


None Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or Multi-Max FA

M-OSFA or M-PG1


M-OSFA or M-PG1




Min. 1.5-inch ACFoam II, FlintBoard ISO or ENRGY 3

OB500 Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA

OB500 SBS-SA (Optional) SBS-SA SBS-SA -120.0


None Min. 1.5-inch ACFoam II, FlintBoard ISO or ENRGY 3





OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board



None

Min. 1.0-inch ISO 95+ GL, H-Shield, H-Shield CG, ENRGY 3 or JM ISO 3 min. 1.3-inch ACFoam III, Min. 1.5-inch Multi-Max FA3 or Ultra-Max

CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

CR-20 SBS-SA (Optional) SBS-SA SBS-SA -172.5




Sys. No.

Deck (Note 1)




None


CR-20 Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA


HYBRID SYSTEMS:




HA (Optional) Additional layer(s) base insulation

HA Flintlastic Ultra Glass SA



-322.5




HA (Optional) Additional layer(s) base insulation

HA Black Diamond Base Sheet



-375.0


None Min. 1.5-inch ACFoam II, FlintBoard ISO, H-Shield, FlintBoard ISOH

A-PD (Optional) Additional layer(s) base insulation

A-PD SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-180.0




A-PD SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-117.5



A-PD, 6-inch o.c.


A-PD, 6-inch o.c.

SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-217.5


None Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

A-PD, 6-inch o.c.

None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-195.0



D-IS (Optional) Additional layer(s) base insulation

D-IS SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-135.0




D-IS SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-217.5



D-IS None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-195.0



M-OSFA (Optional) Additional layer(s) base insulation

M-OSFA SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-232.5



M-OSFA Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

M-OSFA SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-217.5



M-OSFA None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-195.0



M-PG1 (Optional) Additional layer(s) base insulation

M-PG1 SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-270.0



M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

M-PG1 SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-217.5



M-PG1 None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-195.0




Sys. No.

Deck (Note 1)





OB500 (Optional) Additional layer(s) base insulation

OB500 SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-135.0




OB500 SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-217.5



OB500 None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-195.0



CR-20 (Optional) Additional layer(s) base insulation

CR-20 SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-270.0




CR-20 SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-217.5



CR-20 None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-195.0




Min. 1.5-inch ACFoam II, ENRGY 3, H-Shield, FlintBoard ISO

HA (Optional) Additional layer(s) of base insulation

HA BP-AA3, 24-inch grid

(Optional) BP-AA, SBS-AA

SBS-AA -37.5



Min. 1.5-inch ACFoam II or FlintBoard ISO.

HA Min. 0.25-inch Dens Deck, Dens Deck Prime

HA SBS-TA (Optional) SBS-TA SBS-TA -180.0



(Optional) Min. 1.5-inch ACFoam II or FlintBoard ISO.





-180.0



(Optional) Min. 2-inch ACFoam II, FlintBoard ISO, ENRGY 3 or H-Shield


HA BP-AA or SBS-AA



-225.0



(Optional) Min. 1.5-inch ACFoam II, FlintBoard ISO, H-Shield, FlintBoard ISOH


HA APP-TA (Optional) APP-TA APP-TA -252.5



Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY 3 or H-Shield

HA Min. 0.5-inch Structodek High Density Fiberboard

HA BP-AA or SBS-AA



-227.0



(Optional) Min. 2-inch ACFoam II, FlintBoard ISO, ENRGY 3 or H-Shield


HA SBS-TA or APP-TA


SBS-TA or APP-TA

-232.5




HA Min. 0.25-inch Dens Deck HA BP-AA or SBS-AA



-240.0



Min. 1.5-inch ACFoam II or FlintBoard ISO

HA Min. 0.75-inch FescoBoard (homogeneous)

HA BP-AA or SBS-AA



-412.0




Sys. No.

Deck (Note 1)





Min. 1.5-inch ACFoam II or FlintBoard ISO

HA Min. 0.5-inch DuraBoard (homogeneous)

HA BP-AA or SBS-AA



-430.0



0.5-inch Structodek High Density Fiberboard or min. 0.75-inch Fesco Board (homogeneous)

HA None N/A BP-AA (Optional) BP-AA or SBS-AA

SBS-AA -437.5



0.25-inch Dens Deck, Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board

HA None N/A SBS-TA (Optional) SBS-AA or SBS-TA

SBS-AA or SBS-TA

-302.5




HA None N/A

Flintlastic Ultra Poly SMS Base, torched

(Optional) Flintlastic Ultra Poly SMS Base, torched

SBS-TA -487.5




HA None N/A BP-AA (Optional) BP-AA or SBS-AA

SBS-AA -537.5


None Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY 3 or H-Shield

A-PD Min. 0.5-inch Structodek High Density Fiberboard or Min. 0.25-inch Dens Deck

A-PD BP-AA or SBS-AA



-105.0



A-PD

6-inch o.c.

Min. 0.5-inch Structodek High Density Fiberboard or Min. 0.25-inch Dens Deck

A-PD

6-inch o.c.

BP-AA or SBS-AA



-217.5




A-PD BP-AA, SBS-AA, SBS-TA or APP-TA



-117.5



A-PD, 6-inch o.c.


A-PD, 6-inch o.c.




-217.5


None 0.5-inch Structodek High Density Fiberboard

A-PD, 6-inch o.c.

None N/A BP-AA, SBS-AA



-195.0


None Min. 0.25-inch Dens Deck, Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board

A-PD, 6-inch o.c.

None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-195.0


None Min. 1.5-inch ACFoam II or FlintBoard ISO.

D-IS Min. 0.25-inch Dens Deck D-IS SBS-TA (Optional) SBS-TA SBS-TA -112.5



D-IS Min. 0.25-inch Dens Deck Prime D-IS BP-AA, SBS-AA


SBS-AA or SBS-TA

-297.5



D-IS Min. 0.25-inch Dens Deck Prime D-IS SBS-TA (Optional) SBS-TA SBS-TA -302.5




Sys. No.

Deck (Note 1)




None Min. 2-inch ACFoam II, FlintBoard ISO, ENRGY 3 or H-Shield


D-IS BP-AA or SBS-AA



-225.0




D-IS SBS-TA or APP-TA


SBS-TA or APP-TA

-232.5




D-IS APP-TA (Optional) APP-TA APP-TA -252.5




D-IS BP-AA, SBS-AA or SBS-TA


SBS-AA or SBS-TA

-297.5



D-IS None N/A BP-AA, SBS-AA



-195.0



D-IS None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-195.0



M-OSFA Min. 0.5-inch Structodek High Density Fiberboard

M-OSFA BP-AA or SBS-AA



-127.5



M-PG1 Min. 0.5-inch Structodek High Density Fiberboard

M-PG1 BP-AA or SBS-AA



-180.0



M-OSFA Min. 0.25-inch Dens Deck M-OSFA BP-AA or SBS-AA



-232.5



M-PG1 Min. 0.25-inch Dens Deck M-PG1 BP-AA or SBS-AA



-240.0



M-PG1 Min. 0.25-inch Dens Deck Prime M-PG1 BP-AA, SBS-AA


SBS-AA or SBS-TA

-297.5



M-PG1 Min. 0.25-inch Dens Deck Prime M-PG1 SBS-TA (Optional) SBS-TA SBS-TA -302.5



M-OSFA or M-PG1


M-OSFA or M-PG1

BP-AA or SBS-AA



-225.0



M-OSFA or M-PG1


M-OSFA or M-PG1

SBS-TA or APP-TA


SBS-TA or APP-TA

-232.5




Sys. No.

Deck (Note 1)





M-OSFA or M-PG1


M-OSFA or M-PG1

APP-TA (Optional) APP-TA APP-TA -252.5



M-OSFA or M-PG1


M-OSFA or M-PG1

BP-AA, SBS-AA or SBS-TA


SBS-AA or SBS-TA

-297.5



M-PG1 None N/A BP-AA, SBS-AA



-195.0


None Min. 0.25-inch Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board

M-PG1 None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-195.0



OB500 Min. 0.5-inch Structodek High Density Fiberboard

OB500 BP-AA or SBS-AA



-120.0


None Min. 1.5-inch ACFoam II or FlintBoard ISO.

OB500 Min. 0.25-inch Dens Deck or Dens Deck Prime

OB500 BP-AA, SBS-AA, SBS-TA or APP-TA



-150.0



OB500 Min. 0.25-inch Dens Deck Prime OB500 BP-AA, SBS-AA or SBS-TA


SBS-AA or SBS-TA

-297.5







-225.0




OB500 SBS-TA or APP-TA


SBS-TA or APP-TA

-232.5




OB500 APP-TA (Optional) APP-TA APP-TA -252.5




OB500 BP-AA, SBS-AA or SBS-TA


SBS-AA or SBS-TA

-297.5



OB500 None N/A BP-AA, SBS-AA



-195.0



OB500 None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-195.0




Sys. No.

Deck (Note 1)




None


CR-20

Min. 0.5-inch Structodek High Density Fiberboard or DuraBoard (homogeneous) or min. 1.5-inch FescoBoard (laminated)

CR-20 BP-AA or SBS-AA



-180.0


None

Min. 1.0-inch ISO 95+ GL, H-Shield, H-Shield CG, ENRGY 3 or JM ISO 3 min. 1.3-inch ACFoam III, Min. 1.5-inch Multi-Max FA3 or Ultra-





-225.0


None



CR-20 SBS-TA or APP-TA


SBS-TA or APP-TA

-232.5


None


CR-20 Min. 0.25-inch Dens Deck CR-20 BP-AA or SBS-AA



-240.0



CR-20 None N/A BP-AA, SBS-AA



-195.0



CR-20 None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-195.0



None (Optional) Min. 0.5-inch ACFoam II, FlintBoard ISO, H-Shield, FlintBoard ISOH

OB500 or CR-20


OB500 or CR-20




A-PD, D-IS, M-OSFA, M-PG1, OB500 or CR-20


A-PD, D-IS, M-OSFA, M-PG1, OB500 or CR-20


TABLE 3B: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)

SYSTEM TYPE A-3: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER

System No.

Deck (Note 1)

Primer / Temp Roof Base Insulation Layer Top Insulation Layer Roof Cover (Note 14)

MDP (psf) Type Attach Type Attach Base Ply Cap



TABLE 3B: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)

SYSTEM TYPE A-3: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER

System No.

Deck (Note 1)

Primer / Temp Roof Base Insulation Layer Top Insulation Layer Roof Cover (Note 14)




Flintlastic SA PlyBase, self-adhered


OB500 Min. 1.5-inch ACFoam III, FlintBoard Iso Cold, H-Shield CG or FlintBoard Iso ColdH

OB500 SBS-CA1 None SBS-CA1 -82.5



Flintlastic SA PlyBase, self-adhered





TABLE 3C: STRUCTURAL CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)


System No.

Deck

(Note 1) Primer


Base Ply Cap


C-98. Structural concrete FlintPrime SA SBS-SA (Optional) SBS-SA SBS-SA -555.0

C-99. Structural concrete FlintPrime (ASTM D41) SBS-SA (Optional) SBS-SA SBS-SA -630.0

HYBRID SYSTEMS:

C-100. Structural concrete FlintPrime SA Flintlastic Ultra Glass SA (Optional) SBS-AA, SBS-TA, APP-TA SBS-AA, SBS-TA, APP-TA -52.5

C-101. Structural concrete FlintPrime (ASTM D41) Flintlastic Ultra Glass SA (Optional) SBS-AA SBS-AA -135.0

C-102. Structural concrete FlintPrime (ASTM D41) Black Diamond Base Sheet (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -150.0

C-103. Structural concrete FlintPrime (ASTM D41) Flintlastic Ultra Glass SA (Optional) SBS-TA, APP-TA SBS-TA, APP-TA -322.5

C-104. Structural concrete FlintPrime (ASTM D41) Black Diamond Base Sheet (Optional) BP-AA, SBS-AA SBS-AA -240.0


C-105. Structural concrete FlintPrime (ASTM D41) BP-AA or SBS-AA (Optional) BP-AA, SBS-AA, SBS-TA or APP-TA SBS-AA, SBS-TA or APP-TA -240.0

C-106. Structural concrete FlintPrime (ASTM D41) APP-TA (Optional) APP-TA APP-TA -420.0

C-107. Structural concrete FlintPrime (ASTM D41) SBS-TA (Optional) SBS-TA SBS-TA -542.5


C-108. Structural concrete FlintPrime (ASTM D41) SBS-CA1 (Optional) SBS-CA1 SBS-CA1 -262.5


TABLE 4A: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)


System No.

Deck

(Note 1)

Lightweight Concrete

(Note 13)

Base Insulation Layer Coverboard Roof Cover (Note 14) MDP (psf) Type Attach Type Attach Base Ply Cap


LWC-1 Concrete Min. 200 psi, min. 2-inch Elastizell


A-PD, 6-inch o.c.


A-PD, 6-inch o.c.




A-PD, 6-inch o.c.


A-PD, 6-inch o.c.










LWC-5 Concrete Min. 200 psi, min. 2-inch Celcore, Elastizell or Celcore











A-PD

6-inch o.c.

Min. 0.5-inch Structodek High Density Fiberboard or Min. 0.25-inch Dens Deck

A-PD

6-inch o.c.

BP-AA or SBS-AA



-187.5



A-PD, 6-inch o.c.


A-PD, 6-inch o.c.

BP-AA or SBS-AA, SBS-TA or APP-TA



-217.5



OB500 Min. 0.25-inch Dens Deck or Dens Deck Prime




-150.0




OB500 SBS-TA (Optional) SBS-TA SBS-TA -180.0


Min. 2-inch ACFoam II, FlintBoard ISO, ENRGY 3 or H-Shield





-225.0


TABLE 4A: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)


System No.

Deck

(Note 1)

Lightweight Concrete

(Note 13)

Base Insulation Layer Coverboard Roof Cover (Note 14) MDP (psf) Type Attach Type Attach Base Ply Cap



CR-20





-180.0



CR-20

Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or Dens Deck or Dens Deck Prime

CR-20 BP-AA, SBS-AA, SBS-TA or APP-TA



-180.0

COLD APPLIED SYSTEMS:

LWC-14

Min. 22 ga. steel at max 5 ft spans or structural concrete

Min. 350 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete with Zell Fibers.

Min. 1.5-inch H-Shield CG OB500, 6-inch o.c.

(Optional) Additional layers of base insulation

OB500, 6-inch o.c.

BP-CA3 or SBS-CA3

(Optional) BP-CA3 or SBS-CA3

SBS-CA3 -60.0

LWC-15


Min. 350 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete with Zell Fibers. When walkable, attach LWC with Flintfast #14 and Flintfast 3” Round Plates at 1 per 8 ft2 through to the structural deck.

Min. 1.5-inch H-Shield CG OB500, 6-inch o.c.

(Optional) Additional layers of base insulation

OB500, 6-inch o.c.

BP-CA3 or SBS-CA3


SBS-CA3 -67.5


TABLE 4B: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION or REROOF (Tear-Off)


System No.

Deck

(Note 1)

LWC

(Note 13)

Anchor Sheet Insulation Roof Cover (Note 14) MDP (psf)

Type Fasteners Attach Base Top Attach Base Ply Cap

LWC-16

Min. 22 ga. steel or structural concrete deck.

Minimum 350 psi, minimum 2-inch Elastizell cellular LWIC

Yosemite Venting Base

ES FM-90 Base Ply Fasteners

7-inch o.c. at the 4-inch side lap and 7-inch o.c. at two, equally spaced, staggered rows in the center of the sheet

Min. 1.5-inch ACFoam II

(Optional) Additional layers base insulation

Hot asphalt

BP-AA3, 18-inch grid


SBS-AA -37.5*

LWC-17

Min. 22 ga. steel or structural concrete deck.

Minimum 350 psi, minimum 2-inch Approved or existing cellular LWIC Note: To qualify the LWIC under this assembly, the subject fastener shall achieve an average withdrawal of 88 lbf when tested per TAS 105 or ANSI/SPRI FX-1.

Yosemite Venting Base

ES Twin-Loc Nails

9-inch o.c. at the 4-inch side lap and 9-inch o.c. at two, equally spaced, staggered rows in the center of the sheet

Min. 1.5-inch ACFoam II

(Optional) Additional layers base insulation

Hot asphalt

BP-AA4, 18-inch o.c.


SBS-AA -60.0


TABLE 4C: LIGHTWEIGHT CONCRETE DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)

SYSTEM TYPE E: MECHANICALLY ATTACHED BASE SHEET, BONDED ROOF COVER

System No.

Deck

(Note 1) Lightweight Concrete (Note 13)

Base Sheet Roof Cover (Note 14) MDP (psf)

Type Fasteners Attach Ply Cap


LWC-18


Min. 300 psi, min. 2-inch Approved cellular lightweight insulating concrete. Note: To qualify the LWIC under this assembly, a 1.8-inch Trufast Twin Loc-Nail Assembled Fastener shall achieve an average withdrawal of 73 lbf when tested per TAS 105 or ANSI/SPRI FX-1

Flintlastic SA NailBase Trufast Twin Loc-Nail Assembled Fastener (min. 1.8”)

7-inch o.c. at the min. 2-inch lap and 7-inch o.c. in two (2), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA

SBS-SA SBS-SA -60.0

LWC-19




9-inch o.c. at the min. 2-inch lap and 9-inch o.c. in two (2), equally spaced, staggered center rows; Stress plates shall be primed with FlintPrime (ASTM D41) primer or FlintPrime SA

SBS-SA SBS-SA -60.0

HYBRID SYSTEMS:

LWC-20


Min. 200 psi, min 2-inch Range II Elastizell Lightweight Insulating Concrete.

Glasbase; Flexiglas Base; Flintlastic Base 20; All Weather / Empire Base or Poly SMS Base

Trufast FM-90 Base Sheet Fasteners or Trufast Twin Loc-Nail Assembled Fasteners (1.8 inch)

7½-inch o.c. at the 4-inch lap and 7½-inch o.c. in two (2), equally spaced, staggered center rows


-30.0

LWC-21



Glasbase; Flexiglas Base; Flintlastic Base 20; All Weather / Empire Base or Poly SMS Base


7-inch o.c. at the 4-inch lap and 7-inch o.c. in two (2), equally spaced, staggered center rows


-45.0

LWC-22



Glasbase; Flexiglas Base; Flintlastic Base 20; All Weather / Empire Base

Trufast Twin Loc-Nail Assembled Fastener (min. 1.8”)



-60.0

LWC-23



Flexiglas Base; Flintlastic Base 20 or Poly SMS Base

Trufast FM-90 Base Sheet Fasteners



-67.5




System No.

Deck




LWC-24







-75.0


LWC-25








-30.0

LWC-26



Flintlastic APP Base T Trufast FM-90 Base Sheet Fasteners


(Optional) APP-TA

APP-TA -30.0

LWC-27








-45.0

LWC-28



Flintlastic APP Base T Trufast FM-90 Base Sheet Fasteners


(Optional) APP-TA

APP-TA -45.0

LWC-29


Min. 250 psi, min 2-inch Mearlcrete.


OMG CR Base Ply Fasteners (1.7)




-45.0

LWC-30


Min. 250 psi, min 2-inch Mearlcrete. Poly SMS Base OMG CR Base Ply Fasteners (1.7)




-52.5




System No.

Deck




LWC-31


Min. 300 psi, min 2-inch Mearlcrete.






-52.5

LWC-32


Concrecel Bonding Agent on deck; Min. 300 psi, min 2¼-inch Concrecel Concrete.






-52.5

LWC-33



Glasbase; Flexiglas Base; Flintlastic Base 20; All Weather / Empire Base; Yosemite





-60.0

LWC-34

Min. 22 ga., type B steel at max. 5 ft spans structural concrete

Min. 300 psi, min 2-inch Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture. After setting to support foot traffic, Celcore PVA Curing Compound is applied.

All Weather / Empire Base; Flintlastic Base 20; Poly SMS Base


9-inch o.c. at 4-inch laps and 12-inch o.c. in two (2), equally spaced, staggered center rows

(Optional) BP-AA, SBS-AA or SBS-TA-F

SBS-AA or SBS-TA-F

-60.0

LWC-35






BP-AA or SBS-AA


-67.5

LWC-36



Flexiglas Base; Flintlastic Base 20; Poly SMS Base; Yosemite





-67.5




System No.

Deck




LWC-37








-75.0

LWC-38


Min. 300 psi, min 2-inch Celcore Cellular Concrete. After setting to support foot traffic, Celcore PVA Curing Compound is applied.




BP-AA or SBS-AA


-75.0

COLD APPLIED SYSTEMS:

LWC-39



Flintlastic Base 20; Poly SMS Base




SBS-CA2 -45.0

LWC-40 Min. 22 ga. steel at max 5 ft spans


Glasbase; Flexiglas Base; Poly SMS Base




SBS-CA3 -52.5

LWC-41 Structural concrete


Glasbase; Flexiglas Base; Poly SMS Base




SBS-CA3 -60.0


TABLE 5A: CEMENTITIOUS WOOD FIBER DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)


System No.

Deck

(Note 1)

Base Insulation Layer Top Insulation Layer Roof Cover (Note 14) MDP (psf)

Type Attach Type Attach Base Ply Cap


CWF-1. Tectum Min. 1.5-inch FlintBoard ISO, ACFoam II, ENRGY 3 or Multi-Max FA3

OB500 Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA; or SECUROCK Gypsum-Fiber Roof Board

OB500 SBS-SA (Optional) SBS-SA SBS-SA -45.0*

CWF-2. Tectum Min. 1.0-inch ISO 95+ GL, H-Shield, H-Shield CG, ENRGY 3 or JM ISO 3 min. 1.3-inch ACFoam III, Min. 1.5-inch Multi-Max FA3 or Ultra-Max

CR-20 Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA; or SECUROCK Gypsum-Fiber Roof Board








-45.0*


OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or Dens Deck or Dens Deck Prime




-45.0*

CWF-5. Tectum Min. 1.0-inch ISO 95+ GL, H-Shield, H-Shield CG, ENRGY 3 or JM ISO 3 min. 1.3-inch ACFoam III, Min. 1.5-inch Multi-Max FA3 or Ultra-

CR-20 Min. 0.5-inch Structodek High Density Fiberboard or DuraBoard (homogeneous) or min. 1.5-inch FescoBoard (laminated)




-52.5

CWF-6. Tectum Min. 1.0-inch ISO 95+ GL, H-Shield, H-Shield CG, ENRGY 3 or JM ISO 3 min. 1.3-inch ACFoam III, Min. 1.5-inch Multi-Max FA3 or Ultra-Max

CR-20 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or Dens Deck or Dens Deck Prime

CR-20 BP-AA, SBS-AA, SBS-TA or APP-TA



-52.5


TABLE 5B: CEMENTITIOUS WOOF FIBER DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)


System No.

Deck

(Note 1)

Anchor Sheet Base Insulation Top Insulation Roof Cover (Note 14) MDP (psf)

Type Fasteners Attach Type Attach Type Attach Base Ply Cap

HYBRID SYSTEMS:

CWF-7. Tectum






(Optional) SBS-AA, SBS-TA or APP-TA


-60.0


CWF-8. Tectum





HA

Min. 0.75-inch FescoBoard (homogeneous) or min. 0.5-inch Structodek High Density Fiberboard

HA BP-AA or SBS-AA



-60.0

TABLE 5C: CEMENTITIOUS WOOD FIBER DECKS – NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER


System No.

Deck


Top Insulation Layer Roof Cover (Note 14) MDP (psf)

Type Fasteners Attach Base Ply Cap

CWF-9. Tectum (Optional) One or more layers, any combination, loose laid


OMG Polymer GypTec with 3” GypTec Plate

1 per 2 ft2 BP-AA or SBS-AA



-45.0*







-45.0*



Trufast Twin Loc-Nail Assembled Fasteners (minimum 1-inch embedment into deck)




-45.0*


Min. 0.25-inch Dens Deck or Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board





-45.0*


TABLE 5D: CEMENTITOUS WOOD FIBER DECKS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)


System No.

Deck

(Note 1)


Base Fasteners Attach Ply Cap


CWF-13. Tectum Flintlastic SA NailBase Trufast Twin Loc-Nail Assembled Fastener (min. 1.8”)


SBS-SA SBS-SA -60.0


CWF-14. Tectum All Weather / Empire Base; Yosemite Trufast Insuldeck Loc-Nail Base Sheet Fastener


BP-AA or SBS-AA SBS-AA -30.0*

CWF-15. Tectum All Weather / Empire Base; Yosemite Trufast Insuldeck Loc-Nail Base Sheet Fastener



CWF-16. Tectum Glasbase; Flexiglas Base; All Weather / Empire Base; Yosemite

Simplex Turbo Tube-Lok 9-inch o.c. at the 4-inch lap and 12-inch o.c. in two (2), equally spaced, staggered center rows



-45.0*

CWF-17. Tectum Glasbase; Flexiglas Base; Flintlastic Base 20 or All Weather / Empire Base; Yosemite



BP-AA or SBS-AA SBS-AA, SBS-TA or APP-TA

-67.5


TABLE 6A: GYPSUM DECKS – REROOF (TEAR-OFF)


System No.

Deck Base Insulation Layer Top Insulation Layer Roof Cover (Note 14)



G-1. Existing sound gypsum or gypsum plank



M-OSFA SBS-SA (Optional) SBS-SA SBS-SA -172.5


Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or Multi-Max FA

M-OSFA Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA



Min. 1.5-inch ACFoam II, FlintBoard ISO or ENRGY 3 OB500

Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA or SECUROCK Gypsum-Fiber Roof Board

















-127.5



M-OSFA Min. 0.25-inch Dens Deck M-OSFA BP-AA or SBS-AA



-232.5




M-OSFA BP-AA or SBS-AA, SBS-TA or APP-TA



-202.5







-120.0



OB500 Min. 0.25-inch Dens Deck, Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board




-135.0



CR-20 Min. 0.25-inch Dens Deck or Dens Deck Prime

CR-20 SBS-TA (Optional) SBS-TA SBS-TA -180.0


TABLE 6A: GYPSUM DECKS – REROOF (TEAR-OFF)


System No.

Deck Base Insulation Layer Top Insulation Layer Roof Cover (Note 14)




CR-20





-180.0







-225.0






SBS-TA or APP-TA

-232.5






-240.0


TABLE 6B: GYPSUM DECKS – REROOF (TEAR-OFF)


System No.

Deck

(Note 1)


HYBRID SYSTEMS:







(Optional) SBS-AA, SBS-TA or APP-TA


-60.0



All Weather / Empire Base; Yosemite

Trufast FM-75 or FM-90 Base Sheet Fastener


(Optional) Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY 3 or Multi-Max FA3

HA


HA BP-AA or SBS-AA



-45.0*






HA


HA BP-AA or SBS-AA



-60.0


TABLE 6C: GYPSUM DECKS – REROOF (TEAR-OFF)


System No.

Deck


Top Insulation Layer Roof Cover (Note 14) MDP (psf)

Type Fasteners Attach Base Ply Cap








-45.0*








-45.0*








-45.0*



Min. 0.25-inch Dens Deck or Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board





-45.0*

TABLE 6D: GYPSUM DECKS – REROOF (TEAR-OFF)


System No.

Deck

(Note 1)






SBS-SA SBS-SA -60.0



All Weather / Empire Base; Yosemite

Trufast FM-75 or FM-90 Base Sheet Fastener




Glasbase; Flexiglas Base; All Weather / Empire Base; Yosemite

Simplex Turbo Tube-Lok 9-inch o.c. at the 4-inch lap and 12-inch o.c. in two (2), equally spaced, staggered center rows



-45.0*





BP-AA or SBS-AA SBS-AA, SBS-TA or APP-TA

-67.5


TABLE 7A: RECOVER APPLICATIONS


System No.

Substrate (Notes 1 & 11) Base Insulation Layer Top Insulation Layer Roof Cover (Note 14) MDP



R-1 Existing fully bonded BUR or modified bitumen roof cover

Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA; or SECUROCK Gypsum-Fiber Roof Board.

HA None N/A SBS-SA (Optional) SBS-SA SBS-SA -105.0


Min. 1.5-inch ACFoam II, FlintBoard ISO, ENRGY 3, H-Shield or Multi-Max FA3

HA

Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA; or SECUROCK Gypsum-Fiber Roof Board.


R-3 Existing fully bonded, smooth surface BUR or modified bitumen


A-PD, 6-inch o.c.

None N/A SBS-SA (Optional) SBS-SA SBS-SA -105.0

R-4 Existing fully bonded, mineral surface modified bitumen


A-PD, 6-inch o.c.




A-PD, 6-inch o.c.




A-PD, 6-inch o.c.


A-PD, 6-inch o.c.


R-7 Existing fully bonded, mineral surface BUR or modified bitumen


A-PD, 6-inch o.c.


A-PD, 6-inch o.c.




M-OSFA



R-9 Existing fully bonded, smooth- or granule-surface BUR or modified bitumen


M-PG1 None N/A SBS-SA (Optional) SBS-SA SBS-SA -172.5



M-PG1 None N/A SBS-SA (Optional) SBS-SA SBS-SA -180.0



M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board

M-PG1 SBS-SA (Optional) SBS-SA SBS-SA -172.5




System No.




Min. 1.5-inch ACFoam II, FlintBoard, ENRGY 3 or Multi-Max FA

M-PG1 Min. 0.25-inch Dens Deck primed with FlintPrime or FlintPrime SA

M-PG1 SBS-SA (Optional) SBS-SA SBS-SA -180.0



OB500 None N/A SBS-SA (Optional) SBS-SA SBS-SA -120.0



OB500





CR-20 None N/A SBS-SA (Optional) SBS-SA SBS-SA -172.5



CR-20 None N/A SBS-SA (Optional) SBS-SA SBS-SA -192.5









HYBRID SYSTEMS:



HA None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-105.0



A-PD, 6-inch o.c.



-105.0



A-PD, 6-inch o.c.



-180.0



M-PG1 None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-180.0



OB500 None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-120.0




System No.





CR-20 None N/A SBS-SA-H (Optional) SBS-AA, SBS-TA, APP-TA


-195.0



0.5-inch Structodek High Density Fiberboard or min. 0.75-inch Fesco Board (homogeneous)

HA None N/A BP-AA, SBS-AA



-105.0



HA None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-105.0



HA

Min. 0.5-inch Structodek High Density Fiberboard, Min. 0.75-inch FescoBoard (homogeneous) or Min. 0.5-inch DuraBoard (homogeneous)

HA BP-AA or SBS-AA



-105.0



HA Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board, Dens Deck, Dens Deck Prime




-105.0


Min. 0.5-inch Structodek High Density Fiberboard

A-PD, 6-inch o.c.




-105.0



A-PD, 6-inch o.c.




-180.0


Min. 0.25-inch Dens Deck, Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board

A-PD, 6-inch o.c.




-105.0


Min. 0.25-inch Dens Deck, Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board

A-PD, 6-inch o.c.




-180.0



A-PD, 6-inch o.c.


A-PD, 6-inch o.c.

BP-AA or SBS-AA



-52.5



A-PD, 6-inch o.c.

Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or Dens Deck

A-PD, 6-inch o.c.




-52.5




System No.





A-PD, 6-inch o.c.


A-PD, 6-inch o.c.

BP-AA or SBS-AA



-172.5



A-PD, 6-inch o.c.

Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or Dens Deck

A-PD, 6-inch o.c.




-172.5







-127.5



M-OSFA Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or Dens Deck

M-OSFA




-157.5



M-PG1 None N/A BP-AA, SBS-AA



-180.0


Min. 0.25-inch Dens Deck Prime or SECUROCK Gypsum-Fiber Roof Board

M-PG1 None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-180.0



M-PG1 Min. 0.5-inch Structodek High Density Fiberboard

M-PG1 BP-AA or SBS-AA



-180.0



M-PG1 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board or Dens Deck

M-PG1




-180.0



OB500 None N/A BP-AA, SBS-AA



-120.0



OB500 None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-120.0







-120.0




System No.





OB500 Min. 0.25-inch SECUROCK Gypsum-Fiber Roof Board, Dens Deck or Dens Deck Prime




-120.0



CR-20 None N/A BP-AA, SBS-AA



-195.0



CR-20 None N/A BP-AA, SBS-AA, SBS-TA or APP-TA



-195.0



CR-20 Min. 0.25-inch Dens Deck or Dens Deck Prime

CR-20 SBS-TA (Optional) SBS-TA SBS-TA -180.0



CR-20





-180.0







-225.0






SBS-TA or APP-TA

-232.5






-240.0




OB500 Min. 1.5-inch ACFoam III, FlintBoard Iso Cold, H-Shield CG or FlintBoard Iso ColdH




CR-20 Min. 1.5-inch ACFoam III, FlintBoard Iso Cold, H-Shield CG or FlintBoard Iso ColdH

CR-20 SBS-CA1 None SBS-CA1 -82.5




System No.





A-PD, 6-inch o.c.

None N/A SBS-CA1 None SBS-CA1 -105.0



A-PD, 6-inch o.c.


A-PD, 6-inch o.c.




A-PD, 6-inch o.c.


A-PD, 6-inch o.c.




M-PG1 None N/A SBS-CA1 None SBS-CA1 -105.0



M-OSFA, M-PG1


M-OSFA, M-PG1




OB500 None N/A SBS-CA1 None SBS-CA1 -105.0







CR-20 None N/A SBS-CA1 None SBS-CA1 -105.0




CR-20 SBS-CA1 None SBS-CA1 -105.0

TABLE 7B: RECOVER APPLICATIONS – NEW CONSTRUCTION OR REROOF (TEAR-OFF)


System No.

Substrate

(Notes 1 & 11) Primer


Base Ply Cap

R-65 Existing fully bonded BUR over structural concrete deck (Optional) FlintPrime (ASTM D41) SBS-CA1 None SBS-CA1 -187.5

(203) 262-9245 EVALUATION REPORT Evaluation Report … · EXTERIOR RESEARCH & DESIGN, LLC....

Documents

Transcript of (203) 262-9245 EVALUATION REPORT Evaluation Report … · EXTERIOR RESEARCH & DESIGN, LLC....