Oxford, CT 06478 FAX: (203) 262-9243 EVALUATION REPORT ......¾ Firestone UltraPly TPO is a nominal...

EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization #9503

353 Christian Street Oxford, CT 06478 PHONE: (203) 262-9245 FAX: (203) 262-9243 EVALUATION REPORT Firestone Building Products Company, LLC. 250 West 96th Street Indianapolis, IN 46260

Evaluation Report F8970.02.08-R6 FL10264-R6

Date of Issuance: 02/07/2008 Revision 6: 06/22/2011

SCOPE: This Evaluation Report is issued under Rule 9N-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been designed to comply with the 2007 Florida Building Code. DESCRIPTION: Firestone UltraPly TPO Single Ply Roof Systems LABELING: Each unit shall bear labeling in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. Trinity|ERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words “Trinity | ERD Evaluated” may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 4, plus a 36-page Appendix. Prepared by:

Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCA ANE1983

The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 06/22/2011 This does not serve as an electronically signed document. Signed, sealed hardcopies have been transmitted to the Product Approval Administrator and to the named client

CERTIFICATION OF INDEPENDENCE: 1. Exterior Research & Design, LLC. d/b/a Trinity | ERD does not have, nor does it intend to acquire or will it

acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Exterior Research & Design, LLC. d/b/a Trinity | ERD is not owned, operated or controlled by any company

manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or

distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in

the approval process of the product.

Exterior Research and Design, LLC. Evaluation Report F8970.02.08-R6 Certificate of Authorization #9503 FL10264-R6 Revision 6: 06/22/2011 of 4

ROOFING SYSTEMS EVALUATION:

1. SCOPE:

Product Category: Roofing Sub-Category: Single Ply Roof Systems Compliance Statement: Firestone UltraPly TPO and UltraPly TPO XR Single Ply Roof Systems, as produced by Firestone Building Products, have demonstrated compliance with the following sections of the Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein.

2. STANDARDS:

Section Property Standard Year 1504.3.1 Wind FM 4470 1992

1504.3.1 Wind UL 1897 1998

1504.7 Impact FM 4470 1992

1523.6.2 System Performance TAS 114 1995

1523.6.2 Physical Properties TAS 131 1995

3. REFERENCES:

Entity Examination Reference Date ACRC, LLC (TST4671) TAS 114 ACRC 05-002 01/18/2005 ACRC, LLC (TST4671) TAS 114 ACRC 02-002 01/07/2003 ACRC, LLC (TST4671) TAS 114 ACRC 06-030 08/21/2006 ERD (TST 6049) FM 4470 F12260.02.09-2 02/04/2009 ERD (TST 6049) FM 4470 F34280.11.10 11/16/2010 FM Approvals (TST1867) FM 4470 3001925 05/24/1999 FM Approvals (TST1867) FM 4470 3003830 05/26/1999 FM Approvals (TST1867) FM 4470 3004249 11/03/1999 FM Approvals (TST1867) FM 4470 3006983 02/08/2000 FM Approvals (TST1867) FM 4470 3014031 07/22/2002 FM Approvals (TST1867) FM 4470 3014918 12/17/2003 FM Approvals (TST1867) FM 4470 3012931 04/30/2004 FM Approvals (TST1867) FM 4470 3016670 04/29/2004 FM Approvals (TST1867) FM 4470 3017210 04/30/2004 FM Approvals (TST1867) FM 4470 3009473 04/30/2004 FM Approvals (TST1867) FM 4470 3020394 09/03/2004 FM Approvals (TST1867) FM 4470 3022988 01/28/2005 FM Approvals (TST1867) FM 4470 3026519 12/14/2006 FM Approvals (TST1867) FM 4470 3026520 12/14/2006 FM Approvals (TST1867) FM 4470 3027508 02/07/2007 FM Approvals (TST1867) FM 4470 3030227 06/18/2007 FM Approvals (TST1867) FM 4470 3028164 11/02/2007 FM Approvals (TST1867) FM 4470 3030650 05/16/2008 FM Approvals (TST1867) FM 4470 3033218 08/12/2008 FM Approvals (TST1867) FM 4470 3035017 04/15/2009 FM Approvals (TST1867) FM 4470 3032272 05/22/2009 FM Approvals (TST1867) FM 4470 3033947 05/29/2009 FM Approvals (TST1867) FM 4470 3036642 10/09/2009 FM Approvals (TST1867) FM 4470 3036747 10/09/2009 FM Approvals (TST1867) FM 4470 797-05444-267 04/07/2010 FM Approvals (TST1867) FM 4470 797-05604-267 06/02/2010 FM Approvals (TST1867) FM 4470 797-05627-267 06/14/2010 FM Approvals (TST1867) FM 4470 797-05639-267 06/16/2010 FM Approvals (TST1867) FM 4470 797-05829-267 08/30/2010 FM Approvals (TST1867) FM 4470 3040535 10/05/2010 FM Approvals (TST1867) FM 4470 3037109 11/18/2010 FM Approvals (TST1867) FM 4470 3038546 12/17/2010 FM Approvals (TST1867) FM 4470 3041694 01/14/2011 FM Approvals (TST1867) FM 4470 3039133 04/07/2011 FM Approvals (TST1867) FM 4470 3041535 06/08/2011 Underwriters Labs (TST1740) UL 1897 10CA20078 11/20/2010 Underwriters Labs (TST1740) UL 1897 10NK13003 06/13/2011 Underwriters Labs (QUA1743) Quality Control Service Confirmation Exp. 02/09/2014 Miami-Dade BCCO (CER1592) Physical Properties Various NOAs Current


4. PRODUCT DESCRIPTION:

The following roof covers are mechanically attached or fully adhered to Approved substrates using fasteners, stress plates and adhesives, as outlined in the Limitations / Conditions of Use herein.

Firestone UltraPly TPO is a nominal 45-mil (1.1 mm) or 60-mil (1.5 mm) thick, polyester scrim reinforced, single-ply roof membrane.

Firestone UltraPly TPO XR is a nominal 45-mil (1.1 mm) (XR 100) or 60-mil (1.5 mm) (XR 115) thick, polyester reinforced, single-ply roof membrane produced with an 8-oz polyester backing.

Firestone UltraPly TPO SA membranes are nominal 45-mil (1.1 mm) or 60-mil (1.5-mm) thick, internally reinforced thermoplastic (TPO) roof covers with a self-adhering backing.

5. LIMITATIONS:

5.1 This Evaluation Report is not for use in HVHZ.

5.2 Refer to a current Roofing Materials Directory for fire ratings of this product.

5.3 For steel deck installations, foam plastic insulation shall be separated from the building interior in accordance with FBC 2603.4 unless the exceptions stated in FBC 2603.4.1 or 2603.6 apply.

5.4 Unless otherwise noted in Appendix 1, roof decking and its attachment shall be specified and installed to meet project design criteria to the satisfaction of the AHJ.

5.5 For recover installations, the existing roof shall be examined in accordance with FBC 1510.

5.6 For mechanically attached insulation or membrane or strip-bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter 16. Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are RAS 117, RAS 137, FM LPDS 1-29 and ANSI/SPRI WD1. Assemblies marked with an asterisk* carry the limitations set forth in Section 2.2.1.5.1(a) of FM LPDS 1-29 for Zone 2/3 enhancements.

5.7 For assemblies with all components fully bonded in place, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis is permitted for these systems.

5.8 For mechanically attached insulation or membrane over existing roof decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with TAS 105 or ANSI/SPRI FX-1.

5.9 For bonded insulation or membrane over existing substrates in a re-roof (tear off) or recover installation, the existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If any surface conditions exist that bring system performance into question, field uplift testing in accordance with ASTM E907, FM LPDS 1-52 or ANSI/SPRI IA-1 shall be conducted on mock-ups of the proposed new roof assembly.

5.10 For bonded insulation or membrane over existing substrates in a recover installation, the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the AHJ, as documented through field uplift testing in accordance with ASTM E907 or FM LPDS 1-52.

5.11 Metal edge attachment (except gutters), shall be designed and installed for wind loads in accordance with FBC Chapter 16 and tested for resistance in accordance with ANSI/SPRI ES-1 or RAS 111, except the basic wind speed shall be determined from FBC Figure 1609.

5.12 All products in the roof assembly shall have quality assurance audit in accordance with the FBC and F.A.C. Rule 9N-3.


6. INSTALLATION:

6.1 Firestone UltraPly TPO and UltraPly TPO XR shall be installed in accordance with Firestone Building Products published installation instructions, subject to the Limitations / Conditions of Use noted herein.

6.2 System attachment requirements for wind load resistance are set forth in Appendix 1.

6.3 For mechanically fastened membrane systems (Type D) over profiled steel deck, membrane shall be installed running perpendicular to steel deck flutes.

6.4 For InvisiWeld installations, care shall be taken to ensure that the InvisiWeld Plates do not line-up with seams in the TPO membrane. This condition precludes proper induction welding of the membrane to the InvisiWeld Plates.

7. BUILDING PERMIT REQUIREMENTS:

As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product.

8. MANUFACTURING PLANTS:

Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 9N-3 QA requirements.

9. QUALITY ASSURANCE ENTITY:

Underwriters Laboratories – QUA1743; (414) 248-6409; [email protected]

- THE 36-PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT –

Exterior Research and Design, LLC. d/b/a Trinity | ERD Evaluation Report F8970.02.08-R6 for FL10264-R6 Certificate of Authorization #9503 Revision 6: 06/22/2011 Prepared by: Robert Nieminen, PE-59166 Appendix 1, Page 1 of 36

APPENDIX 1: ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE

Table Deck Application Type Description Page

1A-1 Wood New, Reroof (Tear-Off), Recover C-1 Mechanically Attached Insulation, Bonded Roof Cover 4

1A-2 Wood New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover 5

1B Wood New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically Attached Roof Cover 5

1C Wood New, Reroof (Tear-Off), Recover E Non-Insulated, Mechanically Attached Roof Cover 5

1D Wood New Construction F Non-Insulated, Bonded Roof Cover 6

2A-1 Steel or Conc. New, Reroof (Tear-Off), Recover B-1 Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 7-8

2A-2 Steel or Conc. New, Reroof (Tear-Off), Recover B-2 Mech. Attached Base Insulation, Bonded Temp Roof, Bonded Top Insulation, Bonded Roof Cover 9

2B-1 Steel or Conc. New, Reroof (Tear-Off), Recover C-1 Mechanically Attached Insulation, Bonded Roof Cover 10-12

2B-2 Steel or Conc. New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover 13-14

2C-1 Steel or Conc. New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically Attached Roof Cover (Stress Plates) 15-16

2C-2 Steel or Conc. New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically Attached Roof Cover (Battens) 17-19

3A-1 Concrete New, Reroof (Tear-Off) A-1A Bonded Insulation, Bonded Roof Cover 20-23

3A-2 Concrete New, Reroof (Tear-Off) A-1B Bonded Temp Roof, Bonded Insulation, Bonded Roof Cover 24

3B Concrete New, Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 25

4A LWIC New, Reroof (Tear-Off) A-1A Bonded Insulation, Bonded Roof Cover 26-27

4B LWIC New, Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 27-28

5A CWF New, Reroof (Tear-Off) A-1A Bonded Insulation, Bonded Roof Cover 29

5B CWF New, Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 29

6A Gypsum Reroof (Tear-Off) A-1A Bonded Insulation, Bonded Roof Cover 30

6B Gypsum Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 30

7A Various Recover A-1A Bonded Insulation, Bonded Roof Cover 31-32

7B Steel Recover C-2 Plate-Bonded Roof Cover 33

7C Steel Recover D-1 Insulated, Mechanically Attached Roof Cover 34

7D Steel Recover D-2 Insulated, Mechanically Attached Roof Cover (RMA Strips) 35

7E Steel Recover E Non-Insulated, Mechanically Attached Roof Cover 35

7F Various Recover F Non-Insulated, Bonded Roof Cover 36


The following notes apply to the systems outlined herein:

1. Roof decks shall be in accordance with FBC requirements to the satisfaction of the AHJ. Wind load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation.

2. Unless otherwise noted, fasteners and stress plates for insulation attachment shall be as follows. Fasteners shall be of sufficient length for the following engagements:

Wood Deck: Firestone All-Purpose or Heavy-Duty Fasteners with Firestone Insulation Fastening Plates. Minimum 1-inch plywood penetration or wood plank embedment.

Steel Deck: Firestone All-Purpose or Heavy-Duty Fasteners with Firestone Insulation Fastening Plates. Minimum ¾-inch steel penetration, engage the top flute of the steel deck.

Concrete Deck: Firestone Heavy-Duty or Concrete Drive Fasteners with Firestone Insulation Fastening Plates. Minimum 1-inch embedment. Fasteners installed with a pilot hole in accordance with the fastener manufacturer’s published installation instructions.

3. Unless otherwise noted, insulation may be any one layer or combination of polyisocyanurate, polystyrene, wood fiberboard, perlite, DensDeck, DensDeck Prime, DensDeck DuraGuard or SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board that meets the QA requirements of F.A.C. Rule 9N-3 and is documented as meeting FBC 1505.1 and, for foam plastic, FBC 2603.4.1 or 2603.6, when installed with the roof cover.

4. Minimum 200 psi, minimum 2-inch thick lightweight insulating concrete may be substituted for rigid insulation board for System Type D-1 (mechanically attached membrane), whereby the membrane fasteners are installed through the LWIC to engage the structural steel or concrete deck. The structural deck shall be of equal or greater configuration to the steel and concrete deck listings.

5. Preliminary insulation attachment for System Type D = Minimum four fasteners per 4 x 8 ft board or minimum two fasteners per 4 x 4 ft board.

6. Unless otherwise noted, insulation adhesive application rates are as follows. Ribbon or bead width is at the time of application; the ribbons/beads shall expand as noted in the manufacturer’s published instructions:

Firestone I.S.O. Twin Pack: Continuous ½ to ¾-inch beads, 12-inch o.c. Firestone I.S.O. Stick: Continuous ¾ to 1-inch wide ribbons, 12-inch o.c. Firestone I.S.O. Spray S: Continuous ¾ to 1-inch wide ribbons, 12-inch o.c. or Full coverage, 1.0 to 1.6 gal/square. Firestone I.S.O. FIX II: Continuous ¾ to 1-inch wide ribbons, 12-inch o.c. 3M CR-20: Continuous 2½ to 3½-inch ribbons, 12-inch o.c. (Note: TITESET may be used wherever 3M CR-20 is referenced.) Note: When multiple layers(s) of insulation and/or coverboard are installed in ribbon-applied adhesive, adhesive ribbons shall be staggered from layer-

to-layer a distance of one-half the ribbon spacing. Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation board shall be not less than one-half the specified ribbons

spacing.

7. Unless otherwise noted, all insulations are flat stock or taper board of the minimum thickness noted. Tapered ISO 95+ GL at the following thickness limitations may be substituted with the following Maximum Design Pressure (MDP) limitations. In no case shall these values be used to ‘increase’ the MDP listings in the tables; rather if MDP listing below meets or exceeds that listed for a particular system in the tables, then the thinner board listed below may be used as a drop-in for the equivalent thicker material listed in the table.

Firstone I.S.O. Twin Pack: MDP -157.5 psf (Min. 0.5-inch thick) Firestone I.S.O. Stick: MDP -187.5 psf (Min. 0.5-inch thick) Firestone I.S.O. Spray S: MDP -172.5 psf (Min. 0.5-inch thick) Firestone I.S.O. FIX II: MDP -172.5 psf (Min. 0.5-inch thick) 3M CR-20: MDP -117.5 psf (Min. 1.0-inch thick)

8. Bonded polyisocyanurate insulation boards shall be maximum 4 x 4 ft.


9. For mechanically attached components or partially bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter 16, and Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are RAS 117, FM LPDS 1-29 and ANSI/SPRI WD1. Assemblies marked with an asterisk* carry the limitations set forth in Section 2.2.1.5.1(a) of FM LPDS 1-29 for Zone 2/3 enhancements.

10. For assemblies with all components fully bonded in place, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16, and no rational analysis is permitted.

11. For mechanically attached components over existing decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing shall be in accordance with TAS 105 or ANSI/SPRI FX-1.

12. For existing substrates in a bonded recover or re-roof installation, the existing roof surface or existing roof deck shall be examined for compatibility and bond performance with the selected adhesive, and the existing roof system (for recover) shall be capable of resisting project design pressures on its own merit to the satisfaction of the AHJ, as documented through field uplift testing in accordance with ASTM E907, FM LPDS 1-52 or ANSI/SPRI IA-1.

13. For System Type D, steel deck applications, the roof membrane shall be run with its length perpendicular to the steel deck flutes.

14. For Recover Applications using System Type D, the insulation is optional. Alternatively, min. 0.5-inch ISOGARD HD or min. 0.25-inch to 0.625-inch DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board may be used as a separator board, preliminarily attached prior to roof cover installation. The existing roof system shall be suitable for a recover application.

15. For membrane attachment using batten-strips, batten-strip end laps shall be spliced with sufficient dimension to allow for minimum 2-fasteners at each batten-strip lap.

16. For adhered membrane systems, side laps shall be minimum 3-inch wide sealed with min. 1.5-inch heat weld. Membrane adhesive application rates are as follows:

Firestone UltraPly TPO with Firestone UltraPly Bonding Adhesive applied to both the substrate and the bottom side of the roof cover for a combined rate of 60-65 ft2/gal (1.5 m2/L).

Firestone UltraPly TPO with Firestone Water Based Bonding Adhesive S (WBBA) applied to both the substrate and the bottom side of the roof cover for a combined rate of 120 ft2/gal (3.0 m2/L)

Firestone UltraPly TPO with Firestone Single-Ply LVOC Bonding Adhesive applied to both the substrate and the bottom side of the roof cover for a combined rate of 120 ft2/gal (3.0 m2/L).

Firestone UltraPly TPO XR with Firestone XR Bonding Adhesive applied to the substrate only at a rate of 70-90 ft2/gal (1.7-2.2 m2/L) Firestone UltraPly TPO XR with Firestone XR Stick Membrane Adhesive applied in continuous ¾ to 1-inch wide ribbons spaced as noted in the system listings

herein. Firestone UltraPly TPO XR with Firestone I.S.O. Spray S Adhesive applied in continuous ¾ to 1-inch wide ribbons spaced as noted in the system listings herein.

17. For self-adhered membrane systems, side laps shall be minimum 3-inch wide sealed as follows: Firestone UltraPly TPO SA: Lap sealed with min. 1.5-inch heat weld or primed with Firestone Single-Ply QuickPrime Primer and sealed with 3 in. wide Firestone

UltraPly TPO QuickSeam Flashing.

18. For InvisiWeld installations, care shall be taken to ensure that the InvisiWeld Plates do not line-up with seams in the TPO membrane. This condition precludes proper induction welding of the membrane to the InvisiWeld Plates.


TABLE 1A-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER

SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)

Base Insulation Layer Top Insulation Layer

Roof Cover / Adhesive MDP (psf) Type Fasteners Attach

ULTRAPLY TPO SYSTEMS

W-1. Min. 15/32-inch plywood at max 24-inch spans

(Optional) One or more layers, any combination, loose laid

Min. 1-inch ISOGARD HD See Note 2 1 per 2 ft2 UltraPly TPO / UltraPly Bonding Adhesive or WBBA

-45.0*



Min. 2-inch ISO 95+ GL See Note 2 1 per 1.78 ft2 UltraPly TPO / UltraPly Bonding Adhesive or WBBA

-45.0



Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board, DensDeck or DensDeck Prime

See Note 2 1 per 1.6 ft2 UltraPly TPO / UltraPly Bonding Adhesive or WBBA

-45.0

ULTRAPLY TPO SA SYSTEMS



Min. 1-inch ISO 95+ GL Optional Firstone Single-Ply QuickPrime Primer may be applied to the insulation

See Note 2 1 per 2 ft2 UltraPly TPO SA / self-adhered

-37.5*



Min. 0.25-inch DensDeck See Note 2 1 per 2.1 ft2 UltraPly TPO SA / self-adhered

-37.5*


(Optional) One or more layers, min. 1.5-inch, any combination, loose laid

Min. 0.5-inch ISOGARD HD See Note 2 1 per 2.7 ft2 UltraPly TPO SA / self-adhered

-45.0*



Min. 0.5-inch FiberTop C, E or S See Note 2 1 per 2 ft2 UltraPly TPO SA / self-adhered

-45.0*



Min. 1.5-inch ISO 95+ GL Optional Firstone Single-Ply QuickPrime Primer may be applied to the insulation

See Note 2 1 per 2.7 ft2 UltraPly TPO SA / self-adhered

-45.0*



Min. 2-inch ISO 95+ GL Optional Firstone Single-Ply QuickPrime Primer may be applied to the insulation


-45.0


TABLE 1A-2: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER

SYSTEM TYPE C-2: PLATE-BONDED ROOF COVER

System No.

Deck (See Note 1)

Insulation Layer

Attachment Roof Cover MDP (psf)

Fasteners Density / Pattern

W-10.

Min. 19/32-inch plywood at max. 24-inch spans attached using 8d ring shank nails spaced 6-inch o.c.

(Optional) One or more layers, any combination

Firestone Heavy Duty Fasteners and UltraPly TPO InvisiWeld Plates

Max. 6-inch o.c. in rows max. 72-inch o.c.

UltraPly TPO bonded to UltraPly TPO InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps.

-52.5

W-11.

Min. 19/32-inch plywood at max. 24-inch spans attached using No. 8 wood screws spaced 6-inch o.c.

(Optional) One or more layers, any combination




-82.5

TABLE 1B: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER

SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER

System No.

Deck (See Note 1)

Insulation Roof Cover MDP (psf)

Type Attach Membrane Fasteners Attachment

W-12.

Min. 19/32-inch plywood or wood plank at max. 24-inch spans attached using 10d ring shank nails spaced 4-inch o.c. at board edges and 8d ring shank nails spaced 6-inch o.c. in the field

Min. 1.5-inch thick, one or more layers, any combination

Prelim. attached

UltraPly TPO Firestone HD Fasteners with Firestone HD Seam Plates

6-inch o.c. within 6-inch wide laps spaced 90.5-inch o.c. Laps sealed with 5-inch heat weld that encapsulates plates.

-60.0

TABLE 1C: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER

SYSTEM TYPE E: NON-INSULATED, MECHANICALLY ATTACHED ROOF COVER

System No.

Deck (See Note 1)

Roof Cover MDP (psf)

Membrane Fasteners Attachment

W-13. Min. 19/32-inch plywood at max. 24-inch spans attached using 8d ring shank nails spaced 6-inch o.c.

UltraPly TPO Firestone HD Fasteners with Firestone HD Seam Plates

6-inch o.c. within 6-inch wide laps spaced 72-inch o.c. Laps sealed with 1.5-inch heat weld.

-45.0


TABLE 1D: WOOD DECKS – NEW CONSTRUCTION

SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER

System No.

Roof Deck Roof Cover

MDP (psf) Membrane Application

W-14. Min. 7/16-inch thick, UL Classified Firestone CoverDX™ Roof Deck Panel attached to wood supports spaced max. 24-inch o.c. using 8d common nails spaced 6-inch o.c. at all supports.

UltraPly TPO Firestone WBBA at 100 ft2 per gallon. -82.5

W-15.

Min. 7/16-inch thick, UL Classified Firestone CoverDX™ Roof Deck Panel attached to wood supports spaced max. 24-inch o.c. using Spax™ No. 8 x 2-inch long wood to wood screws spaced 6-inch o.c. at all supports.

UltraPly TPO Firestone WBBA at 100 ft2 per gallon. -105.0


TABLE 2A-1: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER

SYSTEM TYPE B-1: MECHANICALLY FASTENED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)

Base Insulation Layer Top Insulation Layer Roof Cover / Adhesive

MDP (psf) Type Fastener Attach Type Attach


SC-1. Min. 22 ga., type B, Grade 33 steel or strutural concrete

Min. 1.5-inch ISO 95+ GL

See Note 2 1 per 2 ft2 Min. 0.5-inch ISOGARD HD I.S.O. Twin Pack UltraPly TPO / UltraPly Bonding Adhesive

-45.0*



See Note 2 1 per 2 ft2 Min. 0.25-inch DensDeck or DensDeck Prime

I.S.O. Twin Pack, I.S.O. Stick or 3M CR-20

UltraPly TPO / UltraPly Bonding Adhesive

-45.0*



See Note 2 1 per 1.6

ft2 Min. 0.5-inch DensDeck or min. 0.5-inch FiberTop E

I.S.O. Spray S (full coverage)


-45.0*

ULTRAPLY TPO XR SYSTEMS



See Note 2 1 per 2 ft2 Min. 0.5-inch FiberTop C, E, or S wood fiber

Hot Asphalt UltraPly TPO XR / XR Bonding Adhesive

-30.0*




ft2 Min. 1.5-inch ISO 95+ GL

I.S.O. FIX II; I.S.O. Spray S (12-inch o.c.); I.S.O. Stick; I.S.O. Twin Pack

UltraPly TPO XR / I.S.O. Spray S or XR Stick, 12-inch o.c.

-30.0*


Min. 2-inch ISO 95+ GL

See Note 2 1 per 4 ft2 Min. 1.5-inch ISO 95+ GL



-37.5*



See Note 2 1 per 4 ft2 Min. 1.5-inch ISO 95+ GL



-45.0*


Min. 0.5-inch DensDeck

See Note 2 1 per 2 ft2

Min. 1.5-inch ISO 95+ GL followed by optional min. 0.5-inch FiberTop C, E or S wood fiber, min. 0.5-inch DensDeck Prime or min. 7/16-inch OSB

I.S.O. Spray S (12-inch o.c.)


-45.0*


Min. 0.5-inch DensDeck

See Note 2 1 per 2 ft2 Min. 1.5-inch ISO 95+ GL followed by min. 0.5-inch ISOGARD HD



-45.0*




Min. 1-inch ISO 95+ GL followed by min. 0.5-inch FiberTop C, E or S wood fiber or min. 0.25-inch DensDeck Prime



-45.0*


TABLE 2A-1: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE B-1: MECHANICALLY FASTENED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)


MDP (psf) Type Fastener Attach Type Attach



See Note 2 1 per 2 ft2 Min. 1-inch ISO 95+ GL followed by min. 0.5-inch ISOGARD HD



-45.0*




ft2 Min. 0.5-inch DensDeck Prime

I.S.O. FIX II; I.S.O. Stick; I.S.O. Twin Pack, 6-inch o.c.


-60.0*




ft2 Min. 1-inch ISO 95+ GL

I.S.O. FIX II; I.S.O. Stick; I.S.O. Twin Pack, 6-inch o.c.


-82.5



See Note 2 1 per 1 ft2 Min. 0.5-inch DensDeck Prime I.S.O. FIX II; I.S.O. Stick; I.S.O. Twin Pack, 4-inch o.c.


-127.5





ft2

Min. 1.5-inch ISO 95+ GL; Optional Firstone Single-Ply QuickPrime Primer or QuickPrime Plus may be applied to the top layer

I.S.O. Twin Pack UltraPly TPO SA / self-adhered

-30.0*




Min. 1.5-inch ISO 95+ GL; Optional Firstone Single-Ply QuickPrime Primer or QuickPrime Plus may be applied to the top layer


-37.5*


Min. 0.5-inch DensDeck or DensDeck Prime

See Note 2 1 per 2 ft2 Min. 1.5-inch ISO 95+ GL followed by min. 0.25-inch DensDeck Prime I.S.O. Twin Pack

UltraPly TPO SA / self-adhered

-37.5*




Min. 1.5-inch ISO 95+ GL followed by min. 1-inch ISO 95+ GL, min. 0.5-inch ISOGARD HD or FiberTop C, E or S; Optional Firstone Single-Ply QuickPrime Primer or QuickPrime Plus may be applied to the top layer.


-45.0*




Min. 1.5-inch ISO 95+ GL followed by min. 0.25-inch DensDeck Prime; Firstone Single-Ply QuickPrime Primer or QuickPrime Plus shall be applied to the top layer.


-45.0*




ft2

Min. 1.5-inch ISO 95+ GL; Firstone Single-Ply QuickPrime Primer shall be applied to the top layer.


-75.0


TABLE 2A-2: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER

SYSTEM TYPE B-2: MECHANICALLY FASTENED BASE INSULATION, BONDED TEMP ROOF, BONDED TOP INSULATION, BONDED ROOF COVER

System No.

Deck

(See Note 1)

Base Insulation Layer Temp Roof

Insulation Roof Cover / Adhesive MDP (psf)

Type Fastener Attach Type Attach


SC-21. Min. 22 ga., type B, Grade 33 steel or structural concrete

Min. 0.75-inch FM Approved perlite See Note 2 1 per 2 ft2

Two plies Firestone Type IV or Type VI in hot asphalt

Min. 1.5-inch ISO 95+ GL followed by min. 0.25-inch DensDeck Prime

Hot asphalt at 25 lbs/square or I.S.O. Stick at 12-inch o.c.

UltraPly TPO / UltraPly Bonding Adhesive, Firestone Single-Ply LVOC or WBBA

-45.0*


Min. 5/8-inch DensDeck Prime See Note 2 1 per 2 ft2

Firestone SA Primer followed by Firestone MB Base SA, self-adhered

One or more layers min. 1.5-inch ISO 95+ GL

I.S.O. Twin Pack at 12-inch o.c.

UltraPly TPO / UltraPly Bonding Adhesive, Firestone Single-Ply LVOC or WBBA

-45.0*



Min. 0.5-inch DensDeck See Note 2 1 per 2 ft2


Min. 1.5-inch ISO 95+ GL followed by optional min. 0.5-inch FiberTop C, E or S wood fiber, min. 0.5-inch DensDeck Prime or min. 7/16-inch OSB



-45.0*


Min. 0.5-inch DensDeck See Note 2 1 per 2 ft2


Min. 1.5-inch ISO 95+ GL followed by min. 0.5-inch ISOGARD HD



-45.0*


TABLE 2B-1: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER

SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)

Base Insulation Layer

Top Insulation Layer Roof Cover / Adhesive

MDP (psf) Type Fasteners Attach




Min. 2-inch ISO 95+ GL See Note 2 1 per 4 ft2 UltraPly TPO / UltraPly Bonding Adhesive

-30.0



Min. 1.5-inch ISO 95+ GL See Note 2 1 per 2.67

ft2 UltraPly TPO / UltraPly Bonding Adhesive

-30.0


Min. 1.5-inch thick, one or more layers, any combination, loose laid

Min. 7/16-inch OSB Firestone HD HailGard Fastener (steel only)

1 per 2.67 ft2


-45.0


One or more layers, any combination, loose laid

Min. 0.5-inch ISOGARD HD See Note 2 1 per 2.67


-45.0*





-60.0



Min. 7/16-inch OSB Firestone HD HailGard Fastener (steel only)

1 per 1.6 ft2 UltraPly TPO / UltraPly Bonding Adhesive

-52.5



Min. 0.5-inch DensDeck Prime See Note 2 1 per 1.33


-75.0



Min. 7/16-inch OSB

Firestone Insulation Fastening Plates Firestone HD Fasteners or Firestone Concrete Drive (concrete only)

1 per 2 ft2 UltraPly TPO / UltraPly Bonding Adhesive

-75.0



Min. 1.5-inch Firestone HailGard

Firestone Insulation Fastening Plates with Firestone HD Fasteners or Firestone Concrete Drive (concrete only)


-75.0



Min. 2-inch ISO 95+ GL See Note 2 1 per 1.6 ft2 UltraPly TPO / UltraPly Bonding Adhesive

-75.0





-90.0



Min. 0.5-inch DensDeck Prime See Note 2 1 per 1 ft2 UltraPly TPO / UltraPly Bonding Adhesive

-105.0


TABLE 2B-1: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)






Min. 7/16-inch OSB



-150.0



Min. 1.5-inch Firestone HailGard



-150.0




Min. 2-inch ISO 95+ GL See Note 2 1 per 4 ft2 UltraPly TPO XR / XR Bonding Adhesive

-30.0



Min. 0.5-inch FiberTop C or S wood fiber See Note 2 1 per 2 ft2


-30.0*



Min. 0.5-inch ISOGARD HD See Note 2 1 per 2.7 ft2 UltraPly TPO XR / XR Bonding Adhesive

-37.5*



Min. 1-inch ISO 95+ GL See Note 2 1 per 2.7 ft2 UltraPly TPO XR / I.S.O. Spray S or XR Stick, 12-inch o.c.

-37.5*



Min. 0.25-inch DensDeck Prime


ft2 UltraPly TPO XR / XR Bonding Adhesive

-45.0*



Min. 0.5-inch FiberTop C, E or S wood fiber

See Note 2 1 per 2 ft2 UltraPly TPO XR / XR Bonding Adhesive

-45.0*




ft2 UltraPly TPO XR / XR Bonding Adhesive

-45.0*



Min. 1.5-inch ISO 95+ GL See Note 2 1 per 2 ft2 UltraPly TPO XR / I.S.O. Spray S or XR Stick, 12-inch o.c.

-45.0*



Min. 2.25-inch ISO 95+ GL See Note 2 1 per 4 ft2 UltraPly TPO XR / I.S.O. Spray S or XR Stick, 12-inch o.c.

-45.0*



Min. 0.5-inch FiberTop E wood fiber, min. 0.25-inch DensDeck Prime or min. 7/16-inch OSB

See Note 2 1 per 2 ft2 UltraPly TPO XR / I.S.O. Spray S or XR Stick, 12-inch o.c.

-45.0*


TABLE 2B-1: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)






Min. 0.5-inch ISOGARD HD See Note 2 1 per 2 ft2 UltraPly TPO XR / I.S.O. Spray S or XR Stick, 4-inch o.c.

-45.0*



Min. 2-inch ISO 95+ GL See Note 2 1 per 1.6 ft2 UltraPly TPO XR / I.S.O. Spray S or XR Stick, 6-inch o.c.

-82.5



Min. 2-inch ISO 95+ GL See Note 2 1 per 1 ft2 UltraPly TPO XR / I.S.O. Spray S or XR Stick, 4-inch o.c.

-142.5




Min. 1-inch ISO 95+ GL; Optional Firstone Single-Ply QuickPrime Primer may be applied to the insulation


-37.5*



Min. 0.25-inch DensDeck See Note 2 1 per 2.1 ft2 UltraPly TPO SA / self-adhered

-37.5*


(Optional) One or more layers, min. 1.5-inch, any combination, loose laid

Min. 0.5-inch ISOGARD HD See Note 2 1 per 2.7 ft2 UltraPly TPO SA / self-adhered

-45.0*



Min. 0.5-inch FiberTop C, E or S


-45.0*



Min. 1.5-inch ISO 95+ GL; Optional Firstone Single-Ply QuickPrime Primer may be applied


-45.0*



Min. 2-inch ISO 95+ GL; Optional Firstone Single-Ply QuickPrime Primer may be applied


ft2 UltraPly TPO SA / self-adhered

-60.0



Min. 1.5-inch ISO 95+ GL; Firestone Single-Ply QuickPrime Primer shall be applied


ft2 UltraPly TPO SA / self-adhered

-82.5



Min. 2-inch ISO 95+ GL; Firstone Single-Ply QuickPrime Primer shall be applied


-82.5



Min. 2-inch ISO 95+ GL; Firstone Single-Ply QuickPrime Primer shall be applied


-112.5


TABLE 2B-2: STEEL or CONCRETE DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER


System No.

Deck (See Note 1)

Insulation Layer

Attachment Roof Cover

MDP (psf) Fasteners Density / Pattern

SC-61.

Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi concrete

One or more layers, any combination

Firestone Heavy Duty Fasteners or Firestone Concrete Drive (concrete only) and UltraPly TPO InvisiWeld Plates



-30.0

SC-62.






-45.0

SC-63.






-82.5

SC-64.




1 per 5.33 ft² (6 parts per 4x8 ft board)

Per FM LPDS 1-29


-45.0*

SC-65.




1 per 4 ft² (8 parts per 4x8 ft board)

Per FM LPDS 1-29


-60.0

SC-66.



Firestone Heavy Duty Fasteners with alternating Rows of: 1.) Firestone UltraPly TPO InvisiWeld Plates 2.) Firestone Insulation Fastening Plates



-67.5


TABLE 2B-2: STEEL or CONCRETE DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-2: PLATE-BONDED ROOF COVER

System No.

Deck (See Note 1)

Insulation Layer

Attachment Roof Cover

MDP (psf) Fasteners Density / Pattern

SC-67.




1 per 2.7 ft² (12 parts per 4x8 ft board)

Per FM LPDS 1-29


-75.0

SC-68.





Per FM LPDS 1-29


-105.0


TABLE 2C-1: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER

SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (STRESS PLATES)

System No.

Deck (See Note 1)



SC-69.

Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel or structural concrete


Prelim. attached

UltraPly TPO

Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Seam Plates or UltraPly TPO Barbed Seam Plates


-30.0



Prelim. attached

UltraPly TPO Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Plus Seam Plates


-30.0

SC-71.



Prelim. attached


18-inch o.c. within 6-inch wide laps spaced 90-inch o.c. Laps sealed with 5-inch heat weld that encapsulates plates.

-37.5

SC-72.



Prelim. attached

UltraPly TPO



-45.0

SC-73.



Prelim. attached

UltraPly TPO or TPO XR

Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Plus Seam Plates


-45.0

SC-74.



Prelim. attached

UltraPly TPO

Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Plus Seam Plates or UltraPly TPO Wide Weld Seam Plates


-45.0

SC-75.



Prelim. attached

UltraPly TPO Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Seam Plates


-45.0



Prelim. attached



-45.0

SC-77.



Prelim. attached

UltraPly TPO

Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Seam Plates or UltraPly TPO Wide Weld Seam Plates


-45.0

SC-78.



Prelim. attached

UltraPly TPO



-52.5


TABLE 2C-1: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (STRESS PLATES)

System No.

Deck (See Note 1)



SC-79.



Prelim. attached


Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Seam Plates


-52.5



Loose Laid

UltraPly TPO Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Seam Plates


-52.5



Prelim. attached



-60.0

SC-82. Min. 22 ga., type B, Grade 33steel or structural concrete


Prelim. attached


Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone HD Plus Seam Plates


-67.5



Prelim. attached



-82.5

SC-84.



Prelim. attached



-90.0


TABLE 2C-2: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER

SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (BATTENS)

System No.

Deck (See Note 1)

Insulation Roof Cover MDP (psf) Type Attach Membrane Fasteners Attachment



Prelim. attached

UltraPly TPO Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone Polymer Batten Strip

Fasteners 12-inch o.c. through batten within 6-inch wide laps spaced 90-inch o.c. Laps sealed with 5-inch heat weld that encapsulates batten.

-30.0


Min. 1.5-inch thick ISO 95+GL

Prelim. attached

UltraPly TPO Firestone HD Plus Fasteners with Firestone Coiled Metal Batten Strip


-30.0

SC-87. Min. 22 ga., type B, Grade 33 steel


Prelim. attached

UltraPly TPO Firestone HD Fasteners with Firestone Coiled Metal Batten Strip


-37.5

SC-88.



Prelim. attached

UltraPly TPO

Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone Coiled Metal Batten Strip


-45.0



Prelim. attached

UltraPly TPO primed on underside with Firestone UltraPly TPO QuickPrime

UltraPly QuickSeam R.M.A. Strips with Firestone HD Fasteners with Firestone Coiled Metal Batten Strip

UltraPly QuickSeam R.M.A. Strips are applied over the insulation spaced 120-inch o.c. The batten is centered over each strip and fastened 6-inch o.c. Roof cover adhered to each strip by first priming at the strip location, then rolling into place with a hand roller.

-45.0



Loose Laid



-52.5

SC-91.



Prelim. attached

UltraPly TPO

Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone Batten Strip or Coiled Metal Batten Strip

Fasteners 6-inch o.c. through batten in field of the roof spaced 144-inch o.c. Battens sealed with 5-inch wide cover strip, with 1.5-inch heat weld on each side of the strip or by applying Firestone TPO QuickSeam Flashing atop batten.

-60.0

SC-92.



Prelim. attached

UltraPly TPO Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone Polymer Batten Strips


-60.0


TABLE 2C-2: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (BATTENS)

System No.

Deck (See Note 1)




Prelim. attached



-60.0



Prelim. attached

UltraPly TPO

Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone Coiled Metal Batten Strip or Firestone Polymer Batten Strip


-67.5



Prelim. attached



-67.5

SC-96.



Prelim. attached

UltraPly TPO

Firestone HD Fasteners or Firestone Concrete Drive (concrete only) with Firestone Batten Strip or Coiled Metal Batten Strip or Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone Polymer Batten Strip


-75.0



Prelim. attached

UltraPly TPO

Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone Batten Strip or Coiled Metal Batten Strip


-82.5



Loose Laid

UltraPly TPO Firestone HD Plus Fasteners with Firestone ¾” Polymer Batten Strips

Fasteners 6-inch o.c. through batten within 6-inch wide laps spaced 68-inch o.c. Laps sealed with 5-inch heat weld that encapsulates battens.

-82.5

SC-99.

Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel


Prelim. attached



-90.0

SC-100.



Prelim. attached

UltraPly TPO

Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone Batten Strip or Coiled Metal Batten Strip


-97.5



Prelim. attached

UltraPly TPO

Firestone HD Plus Fasteners or Firestone Concrete Drive (concrete only) with Firestone Coiled Metal Batten Strip


-112.5


TABLE 2C-2: STEEL or CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (BATTENS)

System No.

Deck (See Note 1)



Min. 0.5-inch Dens Deck or Dens Deck Prime loose laid over min. 1.5-inch thick, one or more layers, any combination

Prelim. attached



-112.5



Loose Laid

UltraPly TPO Firestone HD Plus Fasteners with Firestone ¾” Polymer Batten Strips

Lap Row: Fasteners 6-inch o.c. through battens within 6-inch wide laps spaced 142-inch o.c. Laps sealed with 5-inch heat weld that encapsulates the batten. Field Row: Fasteners 6-inch o.c. through battens in one intermediate row between laps. Batten strips covered with 5-inch wide Ultraply TPO strips sealed on both sides with 1.5-inch heat weld.

-135.0


TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off)

SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)

Primer Base Insulation Layer Top Insulation Layer Roof Cover /

Adhesive MDP (psf)

Type Attach Type Attach


C-1 Min. 2,500 psi concrete

ASTM D41 Min. 1.5-inch ISO 95+ GL with optional Tapered ISO 95+ GL

Hot Asphalt Min. 0.5-inch Firestone FiberTop

Hot Asphalt UltraPly TPO / UltraPly Bonding Adhesive

-135.0


ASTM D41 Min. 1.5-inch ISO 95+ GL

Hot Asphalt (Optional) Tapered ISO 95+ GL

Hot asphalt UltraPly TPO / UltraPly Bonding Adhesive

-180.0


ASTM D41 Min. 1.5-inch ISO 95+ GL with optional Tapered ISO 95+ GL

Hot Asphalt Min. 0.25-inch DensDeck or DensDeck Prime


-195.0


None Min. 1.5-inch ISO 95+ GL

I.S.O. Twin Pack (Optional) Additional layers of base insulation I.S.O. Twin Pack

UltraPly TPO / UltraPly Bonding Adhesive or Single-Ply LVOC Bonding Adhesive

-165.0



I.S.O. Twin Pack, 8-inch o.c.

(Optional) Additional layers of base insulation



-240.0







-285.0



I.S.O. Twin Pack Min. 0.25-inch DensDeck Prime

I.S.O. Twin Pack UltraPly TPO / UltraPly Bonding Adhesive

-127.5



I.S.O. Twin Pack Min. 0.25-inch DensDeck I.S.O. Twin Pack


-157.5







-187.5


None Two layers min. 1.5-inch ISO 95+ GL





-195.0







-247.5


None One or more layers, min. 1.5-inch ISO 95+ GL

I.S.O. Twin Pack Min. 0.5-inch ISOGARD HD I.S.O. Twin Pack UltraPly TPO / WBBA -222.5



I.S.O. Twin Pack Min. 0.5-inch ISOGARD HD


-247.5



3M CR-20 (Optional) Additional layers base insulation 3M CR-20


-270.0



3M CR-20 Min. 0.25-inch DensDeck

3M CR-20 UltraPly TPO / UltraPly Bonding Adhesive

-195.0


TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)


Adhesive MDP (psf)




3M CR-20 Min. 0.25-inch DensDeck Prime 3M CR-20


-240.0



I.S.O. Stick (Optional) Additional layers of base insulation

I.S.O. Stick UltraPly TPO / UltraPly Bonding Adhesive

-150.0



I.S.O. Stick Min. 0.25-inch DensDeck or DensDeck Prime


-150.0



I.S.O. Stick Min. 0.5-inch ISOGARD HD I.S.O. Stick UltraPly TPO / WBBA -247.5



I.S.O. Stick Min. 0.5-inch ISOGARD HD I.S.O. Stick


-300.0


None Min. 0.5-inch ISOGARD HD

I.S.O. Twin Pack None N/A UltraPly TPO / UltraPly Bonding Adhesive or WBBA

-300.0


None Min. 0.5-inch ISOGARD HD

I.S.O. Stick None N/A UltraPly TPO / UltraPly Bonding Adhesive or WBBA

-405.0



I.S.O. FIX II Min. 0.5-inch ISOGARD HD I.S.O. FIX II UltraPly TPO / WBBA -135.0



I.S.O. FIX II Min. 0.5-inch ISOGARD HD

I.S.O. FIX II UltraPly TPO / UltraPly Bonding Adhesive

-300.0







-120.0




Min. 0.5-inch DensDeck or FiberTop E



-120.0

ULTRAPLY TPO XR SYSTEMS IN XR BONDING ADHESIVE



Hot asphalt (Optional) Additional layers of base insulation Hot asphalt

UltraPly TPO XR / XR Bonding Adhesive

-112.5



I.S.O. FIX II; I.S.O. Stick; I.S.O. Twin Pack; I.S.O. Spray S (full coverage)




-112.5


ASTM D41 Min. 0.25-inch DensDeck Prime

Hot Asphalt None N/A UltraPly TPO XR / XR Bonding Adhesive

-232.5


ASTM D41 One or two layers min. 1.5-inch ISO 95+ GL

Hot Asphalt Min. 0.25-inch DensDeck Prime Hot Asphalt


-300.0



System No.

Deck (See Note 1)


Adhesive MDP (psf)


ULTRAPLY TPO XR SYSTEMS IN HOT ASPHALT






UltraPly TPO XR / Hot Asphalt

-127.5


(Optional) ASTM D41


Hot Asphalt None N/A UltraPly TPO XR / Hot Asphalt

-232.5


(Optional) ASTM D41


Hot asphalt (Optional) Additional layers of base insulation

Hot asphalt UltraPly TPO XR / Hot Asphalt

-300.0




-382.5




-487.5


(Optional) ASTM D41




-457.5


(Optional) ASTM D41

Two layers min. 1.5-inch ISO 95+ GL



-300.0

ULTRAPLY TPO XR SYSTEMS IN I.S.O. SPRAY S OR XR STICK:


None

Min. 1-inch OC FOAMULAR Thermapink 25; Insulfoam 1 EPS or min. 2-inch Dow STYROFOAM DECKMATE Plus FA





-112.5



None One or more layers min. 1.5-inch ISO 95+ GL

I.S.O. Twin Pack Min. 0.5-inch FiberTop C, E or S


-52.5



I.S.O. Twin Pack

Min. 0.25-inch DensDeck or DensDeck Prime primed with Firestone QuickPrime Plus


-165.0



I.S.O. Twin Pack Min. 0.50-inch ISOGARD HD I.S.O. Twin Pack


-210.0



I.S.O. Twin Pack

(Optional) Additional layers of base insulation; Top layer shall be primed with Firestone Single-Ply QuickPrime Primer


-292.5




Min. 0.5-inch DensDeck primed with Firestone QuickPrime Plus



-120.0



System No.

Deck (See Note 1)


Adhesive MDP (psf)








-120.0


TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off)

SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER

System No.

Deck

(See Note 1) Primer

Vapor Barrier / Temporary Roof

Base Insulation Layer Top Insulation Layer Roof Cover / Adhesive MDP (psf)



ASTM D41

One or two plies Firestone Type IV (4) M or Type VI (6) M or one ply of MB Base, SBS Base, SBS PolyBase or SBS Premium Base in hot asphalt



(Optional) Min. 0.5-inch ISOGARD HD, min. 0.25-inch DensDeck Prime or min. 7/16-inch OSB


UltraPly TPO / I.S.O Spray S or XR Stick, 4-inch o.c.

-172.5


ASTM D41

One or two plies Firestone Type IV (4) M or Type VI (6) M or one ply of MB Base, SBS Base, SBS PolyBase or SBS Premium Base in hot asphalt

Min. 0.5-inch ISOGARD HD or min. 0.25-inch DensDeck Prime


None N/A UltraPly TPO / I.S.O Spray S or XR Stick, 4-inch o.c.

-172.5


ASTM D41

Firestone MB Base M, adhered in I.S.O. Twin Pack Min. 1.5-inch ISO 95+ GL I.S.O. Twin Pack



-232.5


ASTM D41

Firestone SBS Poly Torch or SBS Glass Torch Base, torch applied

Min. 1.5-inch ISO 95+ GL I.S.O. Twin Pack Min. 0.25-inch DensDeck or DensDeck Prime


-232.5


TABLE 3B: CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off)


System No.

Deck (See Note 1)

Primer Roof Cover

Base Ply Application Top Ply Application MDP (psf)

C-49 Min. 2,500 psi concrete None None N/A UltraPly TPO XR XR Stick, 12-inch o.c. -97.5

C-50 Min. 2,500 psi concrete None None N/A UltraPly TPO XR XR Bonding Adhesive -360.0

C-51 Min. 2,500 psi concrete None None N/A UltraPly TPO XR XR Stick, 6-inch o.c. -150.0

C-52 Min. 2,500 psi concrete ASTM D41 None N/A UltraPly TPO XR 115 XR Bonding Adhesive -180.0

C-53 Min. 2,500 psi concrete ASTM D41 One or two plies Firestone Type IV (4) M or Type VI (6) M or one ply of MB Base, SBS Base, SBS PolyBase or SBS Premium Base

Hot asphalt UltraPly TPO XR I.S.O. Spray S, 4-inch o.c.

-240.0

C-54 Min. 2,500 psi concrete ASTM D41 One or two plies Firestone Type IV (4) M or Type VI (6) M or one ply of MB Base, SBS Base, SBS PolyBase or SBS Premium Base

Hot asphalt UltraPly TPO XR XR Stick, 4-inch o.c. -315.0

C-55 Min. 2,500 psi concrete None None N/A UltraPly TPO XR 115 Hot asphalt -487.5

C-56 Min. 2,500 psi concrete ASTM D41 None N/A UltraPly TPO XR Hot asphalt -382.5

C-57 Min. 2,500 psi concrete None None N/A UltraPly TPO XR I.S.O. Spray S, 4-inch o.c.

-472.5

C-58 Min. 2,500 psi concrete ASTM D41 None N/A UltraPly TPO XR 115 Hot asphalt -495.0


TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off)


System No.

Deck (See Note 1)

Base Insulation Layer Coverboard Roof Cover / Adhesive

MDP (psf)

Struct LWC Type Attachment Type Attachment

LWC-1 Structural concrete

Min. 200 psi, min. 2-inch thick Elastizell cellular LWIC.




-180.0


Min. 200 psi, min. 2-inch thick Celcore cellular LWIC.




-222.5


Min. 200 psi, min. 2-inch thick Mearlcrete cellular LWIC.


3M CR-20 (Optional) Additional layers base insulation

3M CR-20 UltraPly TPO / UltraPly Bonding Adhesive

-240.0




3M CR-20 Min. 0.25-inch DensDeck 3M CR-20


-180.0


Min. 200 psi, min. 2-inch thick Celcore or Mearlcrete cellular LWIC.


3M CR-20 Min. 0.25-inch DensDeck 3M CR-20


-195.0






-180.0






-222.5


Min. 200 psi, min. 2-inch thick Mearlcrete cellular LWIC.




-240.0


Min. 200 psi, min. 2-inch thick Celcore, Elastizell, Mearlcrete or Insulcel cellular LWIC.


I.S.O. Stick (Optional) Additional layers of base insulation I.S.O. Stick


-225.0




I.S.O. Stick Min. 0.25-inch DensDeck


-195.0




I.S.O. Stick Min. 0.25-inch DensDeck Prime I.S.O. Stick


-225.0


TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER

System No.

Deck (See Note 1)

Base Insulation Layer Coverboard Roof Cover / Adhesive

MDP (psf)

Struct LWC Type Attachment Type Attachment








-105.0








-105.0

TABLE 4B: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off)


System No.

Deck (See Note 1) Roof Cover / Adhesive MDP (psf)

Structural Deck LWC

LWC-14 Min. 22 ga., type B, Grade 33 vented steel deck at max. 5 ft spans or min. 2,500 psi structural concrete

Min. 200 psi, min. 2-inch thick Approved cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board.


-67.5


Min. 200 psi, min. 2-inch thick Approved cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft2.


-135.0


Min. 200 psi, min. 2-inch thick Celcore cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board.


-45.0


Min. 200 psi, min. 2-inch thick Celcore cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft2.


-90.0


Min. 250 psi, min. 2-inch thick Approved cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft2. Note: To qualify the LWIC under this assembly, an ES Products FM-90 Fastener shall achieve a MCRF of 100 lbf when tested per TAS 105 or ANSI/SPRI FX-1.


-75.0

LWC-19 Min. 2,500 psi structural concrete Min. 250 psi, min. 2-inch thick Approved cellular LWIC. Note: To qualify the LWIC under this assembly, an ES Products FM-90 Fastener shall achieve a MCRF of 95 lbf when tested per TAS 105 or ANSI/SPRI FX-1.


-467.5


TABLE 4B: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER

System No.

Deck (See Note 1) Roof Cover / Adhesive MDP (psf)

Structural Deck LWC

LWC-20

Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans welded 6-inch o.c. with 3/8-inch welding washers and two Traxx/1 screws at sidelap even btwn spans

Min. 350 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture, with optional 1-inch thick, 1.0 pcf EPS holey board and surfacing of Celcore PVA Curing Compound.

UltraPlyTPO XR / XR Bonding Adhesive

-52.5

LWC-21

Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans attached 6-inch o.c. with Traxx/5 screws and one Traxx/1 screw at sidelap midspan



-60.0

LWC-22




-82.5

LWC-23




-90.0

LWC-24


Min. 350 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture, with optional 1-inch thick, 1.0 pcf EPS holey board and surfacing of Celcore PVA Curing Compound. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft2.


-90.0

LWC-25 Min. 2,500 psi structural concrete Min. 350 psi, min. 2-inch thick Celcore MF Cellular Concrete with Celcore HS Rheology Modifying Admixture, with optional 1-inch thick, 1.0 pcf EPS holey board and surfacing of Celcore PVA Curing Compound.


-90.0

LWC-26


Min. 250 psi, min. 2-inch thick Elastizell Range II Lightweight Insulating Concrete with optional 1-inch thick, 1.0 pcf EPS holey board.


-37.5

LWC-27


Min. 250 psi, min. 2-inch thick Elastizell Range II Lightweight Insulating Concrete with optional 1-inch thick, 1.0 pcf EPS holey board. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft2.


-82.5

LWC-28 Min. 2,500 psi structural concrete Min. 250 psi, min. 2-inch thick Elastizell Range II Lightweight Insulating Concrete with 1-inch thick, 1.0 pcf EPS holey board.


-90.0

LWC-29 Min. 2,500 psi structural concrete Min. 250 psi, min. 2-inch thick Elastizell Range II Lightweight Insulating Concrete. No EPS holey board.


-210.0


TABLE 5A: CEMENTITIOUS WOOD FIBER DECKS - NEW CONSTRUCTION or REROOF (Tear-Off)


System No.

Deck (See Note 1)


MDP (psf) Type Attach Type Attach

CWF-1. Tectum Min. 1.5-inch ISO 95+ GL

I.S.O. Stick (Optional) Min. 0.25-inch DensDeck or DensDeck Prime


-45.0

CWF-2. Tectum Min. 1.5-inch ISO 95+ GL

I.S.O. Spray S, full coverage

(Optional) Min. 0.25-inch DensDeck or min. 0.5-inch FiberTop E

I.S.O. Spray S, full coverage


-45.0

CWF-3. Tectum or Fibroplank


3M CR-20 (Optional) Min. 0.25-inch DensDeck or DensDeck Prime 3M CR-20


-52.5

Table 5B: CEMENTITOUS WOOD FIBER DECKS - NEW CONSTUCTION or REROOF (Tear-Off) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER

System No.

Deck (See

Note 1)

Anchor Sheet Base Insulation Top Insulation Roof Cover /

Adhesive MDP (psf)

Type Fasteners Attach Type Attach Type Attach

CWF-4. Tectum

SBS Base, SBS Premium Base, MB Base or APP 160

Two Piece Locking Nail

9-inch o.c. in the min. 2-inch lap and 18-inch o.c. in two, equally spaced center rows


I.S.O. Stick

(Optional) Min. 0.25-inch DensDeck or DensDeck Prime

I.S.O. Stick


-45.0*


TABLE 6A: GYPSUM DECKS - REROOF (Tear-Off)


System No.

Deck (See Note 1)


MDP (psf) Type Attach Type Attach

G-1. Existing poured gypsum or gypsum plank


I.S.O. Twin Pack (Optional) Additional layers of base insulation I.S.O. Twin Pack


-165.0



I.S.O. Twin Pack Min. 0.25-inch DensDeck Prime I.S.O. Twin Pack UltraPly TPO / UltraPly Bonding Adhesive

-127.5



I.S.O. Twin Pack Min. 0.25-inch DensDeck I.S.O. Twin Pack UltraPly TPO / UltraPly Bonding Adhesive

-157.5





-257.5



3M CR-20 Min. 0.25-inch DensDeck 3M CR-20 UltraPly TPO / UltraPly Bonding Adhesive

-195.0



3M CR-20 Min. 0.25-inch DensDeck Prime 3M CR-20 UltraPly TPO / UltraPly Bonding Adhesive

-240.0



I.S.O. Stick (Optional) Min. 0.25-inch DensDeck or DensDeck Prime


-112.5

Table 6B: GYPSUM DECKS - NEW CONSTUCTION or REROOF (Tear-Off) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER

System No.

Deck (See

Note 1)

Anchor Sheet Base Insulation Top Insulation Roof Cover /

Adhesive MDP (psf)

Type Fasteners Attach Type Attach Type Attach

G-8.

Existing poured gypsum or gypsum plank

SBS Base, SBS Premium Base, MB Base or APP 160

Two Piece Locking Nail

9-inch o.c. in the min. 2-inch lap and 18-inch o.c. in two, equally spaced center rows


I.S.O. Stick


I.S.O. Stick


-45.0*


TABLE 7A: RECOVER APPLICATIONS


System No.

Substrate (See Note 12)

Base Insulation Layer Top Insulation Layer Roof Cover

MDP (psf) Type Attachment Type Attachment


R-1 Existing asphaltic BUR or mineral surface cap sheet

Min. 1.5-inch ISO 95+ GL with optional Tapered ISO 95+ GL

Hot Asphalt Min. 0.5-inch Firestone FiberTop


-135.0


Min. 1.5-inch ISO 95+ GL Hot Asphalt (Optional) Tapered ISO 95+ GL

Hot asphalt UltraPly TPO / UltraPly Bonding Adhesive

-180.0


Min. 1.5-inch ISO 95+ GL with optional Tapered ISO 95+ GL

Hot Asphalt Min. 0.25-inch DensDeck or DensDeck Prime


-195.0


Min. 1.5-inch ISO 95+ GL I.S.O. Twin Pack



-157.5


(Optional) Min. 1.5-inch ISO 95+ GL

I.S.O. Twin Pack Min. 0.5-inch ISOGARD HD I.S.O. Twin Pack


-157.5


Min. 1.5-inch ISO 95+ GL 3M CR-20 (Optional) Additional layers base insulation 3M CR-20


-262.5


Min. 1.5-inch ISO 95+ GL 3M CR-20 Min. 0.25-inch DensDeck 3M CR-20


-195.0


Min. 1.5-inch ISO 95+ GL 3M CR-20 Min. 0.25-inch DensDeck Prime 3M CR-20


-240.0


Min. 1.5-inch ISO 95+ GL I.S.O. Stick



-120.0



I.S.O. Stick Min. 0.5-inch ISOGARD HD


-120.0

R-11 Existing asphaltic BUR Min. 1.5-inch ISO 95+ GL I.S.O. Spray S (full coverage)




-112.5





-112.5


R-13 Existing asphaltic BUR Min. 0.25-inch DensDeck Prime or min. 0.5-inch ISOGARD HD


None N/A UltraPly TPO XR / I.S.O. Spray S or XR Stick, 4-inch o.c.

-45.0


TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER

System No.


Base Insulation Layer Top Insulation Layer Roof Cover

MDP (psf) Type Attachment Type Attachment

R-14 Existing asphaltic BUR over structural concrete deck



(Optional) Min. 0.5-inch ISOGARD HD or min. 0.25-inch DensDeck Prime


UltraPly TPO / I.S.O Spray S or XR Stick, 4-inch o.c.

-172.5





-172.5

R-16

Existing granule-surfaced, asphaltic modified bitumen roof cover over structural concrete deck

Min. 1-inch ISO 95+ GL I.S.O. Spray S (12-inch o.c.)

(Optional) Min. 0.5-inch ISOGARD HD, min. 0.25-inch DensDeck Prime or min. 7/16-inch OSB


UltraPly TPO / I.S.O Spray S, 4-inch o.c.

-172.5

R-17

Existing granule-surfaced, asphaltic modified bitumen roof cover over structural concrete deck




-172.5

R-18

Existing asphaltic BUR or mineral surface cap sheet over structural concrete or steel deck

Min. 0.25-inch DensDeck Prime Hot Asphalt None N/A

UltraPly TPO XR / Firestone XR Bonding Adhesive

-300.0

R-19

Existing asphaltic BUR or mineral surface cap sheet over structural concrete or steel deck

Min. 0.25-inch DensDeck Prime Hot Asphalt None N/A


-457.5




I.S.O. Twin Pack Min. 0.5-inch ISOGARD HD


-157.5



I.S.O. Twin Pack

Min. 0.25-inch DensDeck or DensDeck Prime primed with Firestone QuickPrime Plus


-157.5


Min. 0.5-inch DensDeck primed with Firestone QuickPrime Plus



-112.5





-112.5


TABLE 7B: STEEL - RECOVER


System No.


Insulation Layer Attachment

Roof Cover / Adhesive MDP (psf) Fasteners Spacing

R-24

Existing standing seam or lap seam metal roof covers having min. 3/16-inch to max. ¼-inch thick steel purlins spaced max. 60-inch o.c.

One or more layers, any combination, preliminarily fastened per FM Approvals requirements

Firestone Purlin Fasteners and UltraPly TPO InvisiWeld Plates are fastened through to purlins

18-inch o.c. along purlins

UltraPly TPO bonded to UltraPly TPO InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps. (All areas where the existing metal panels do not lay flush on the underlying purlin shall have a 0.25-inch diameter pilot hole pre-drilled into the panel prior to driving the Purlin Fastener into the purlin.)

-30.0

R-25






-45.0

R-26

Existing standing seam or lap seam metal roof covers having min. ¼-inch thick steel purlins spaced max. 120-inch o.c.





-52.5

R-27






-82.5


TABLE 7C: STEEL - RECOVER

SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER

System No.

Deck Insulation Roof Cover MDP

(psf) Type Attach Membrane Fasteners Attachment

R-28



Prelim. attached

UltraPly TPO

Firestone Purlin Fasteners and Firestone HD Seam Plates

18-inch o.c. within 6-inch wide laps spaced max. 72-inch o.c. to engage steel purlin. Laps sealed with 1.5-inch heat weld. (All areas where the existing metal panels do not lay flush on the underlying purlin shall have a 0.25-inch diameter pilot hole pre-drilled into the panel prior to driving the Purlin Fastener into the purlin.)

-30.0

R-29



Prelim. attached

UltraPly TPO



-30.0

R-30



Prelim. attached

UltraPly TPO

Firestone Purlin Fasteners and Firestone Coiled Metal Batten Strips

12-inch o.c. within 6-inch wide laps spaced max. 142-inch o.c. to engage steel purlin. Laps sealed with 5-inch heat weld that encapsulates the batten and fasteners or are primed with UltraPly TPO QuickPrime and sealed with UltraPly TPO QuickSeam Flashing. (All areas where the existing metal panels do not lay flush on the underlying purlin shall have a 0.25-inch diameter pilot hole pre-drilled into the panel prior to driving the Purlin Fastener into the purlin.)

-30.0

R-31



Prelim. attached

UltraPly TPO



-45.0

R-32



Prelim. attached

UltraPly TPO



-52.5


TABLE 7D: STEEL - RECOVER

SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED ROOF COVER (RMA Strips)

System No.

Deck Insulation Roof Cover MDP

(psf) Type Attach Membrane Fasteners Attachment

R-33



Prelim. attached

UltraPly TPO

Firestone Purlin Fasteners and Firestone Coiled Metal Batten Strip

Firestone UltraPly QuickSeam R.M.A. Strips are applied over the insulation spaced 120-inch o.c. positioned over each steel purlin location. The batten is centered over each strip and fastened into the purlins 6-inch o.c. (All areas where the existing metal panels do not lay flush on the underlying purlin shall have a 0.25-inch diameter pilot hole pre-drilled into the panel prior to driving the Purlin Fastener into the purlin.) Roof cover adhered to each strip by first priming the membrane underside with Firestone UltraPly TPO QuickPrime at the strip location, then rolling into place with a hand roller. The min. 2-inch side laps are sealed with a min. 1.5-inch outside heat weld.

-45.0

TABLE 7E: RECOVER APPLICATIONS

SYSTEM TYPE E: NON-INSULATED, MECHANICALLY ATTACHED ROOF COVER

System No.

Deck (See Note 1) Roof Cover MDP (psf)

R-34 Min. 22 ga., type B, Grade 33 steel or structural concrete

UltraPly TPO XR Firestone HD Fasteners with Firestone HD Seam Plates


-30.0

R-35 Min. 22 ga., type B, Grade 80 steel UltraPly TPO XR Firestone HD Plus Fasteners with Firestone HD Plus Seam Plates


-45.0

R-36 Min. 22 ga., type B, Grade 33 steel or structural concrete

UltraPly TPO XR Firestone HD Fasteners with Firestone HD Seam Plates


-45.0

R-37 Min. 22 ga., type B, Grade 80 steel UltraPly TPO XR Firestone HD Plus Fasteners with Firestone HD Plus Seam Plates


-67.5


TABLE 7F: RECOVER APPLICATIONS


System No.

Deck (See Note 1)

Primer Roof Cover

Type Application MDP (psf)

R-38 Existing asphaltic BUR None UltraPly TPO XR I.S.O. Spray S or XR Stick, 12-inch o.c.

-45.0

R-39 Existing granule-surfaced, asphaltic modified bitumen roof cover

None UltraPly TPO XR I.S.O. Spray S or XR Stick, 6-inch o.c.

-142.5


None UltraPly TPO XR I.S.O. Spray S, 4-inch o.c. -240.0


None UltraPly TPO XR XR Stick, 4-inch o.c. -315.0

R-42 Existing asphaltic BUR or mineral surface cap sheet over structural concrete or steel deck

None UltraPly TPO XR Hot asphalt -495.0

Oxford, CT 06478 FAX: (203) 262-9243 EVALUATION REPORT ......¾ Firestone UltraPly TPO is a nominal...

Documents

Transcript of Oxford, CT 06478 FAX: (203) 262-9243 EVALUATION REPORT ......¾ Firestone UltraPly TPO is a nominal...