2008 Accord 2 and 4 Door Accessory Bluetooth Handsfreelink
Transcript of 2008 Accord 2 and 4 Door Accessory Bluetooth Handsfreelink
-
Publications No.
Issue DateINSTALLATIONINSTRUCTIONS
Accessory Application
2007 American Honda Motor Co., Inc. All Rights Reserved. 1 of 2508E02-TA0-1001-91
Accessory Hands Free Link2008 ACCORD 2 AND 4-DOOR
PARTS LIST
HFL Attachment KitP/N 08E02-TA0-100
HFL trim
HFL bracket
HFL harness
2 Double-sided tapes A
Double-faced tape B (May not be used with some vehicles)
Template
Fuse label
Fuse (2A)
7 EPT sealers (1 Not used)
26 Wire ties (4 Not used)
NOV 2007
HFL retainer
AII 38281
AII 38281 (0711)
HFL sub harness
-
2 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
4 Self-tapping screws, 3 x 10 mm
2 Washer screws, 4 x 12 mm
Ground bolt
Clip
2
2 Self-tapping screws
HFL KitP/N 08E00-E10-100
Switch
Control unit
TOOLS AND SUPPLIES REQUIRED
#2 Phillips screwdriver
Flat-tip screwdriver
Shop towel
Diagonal cutters
Ratchet
10 mm Socket
10 mm Combination wrench
Utility Knife
T15 TORX bit
Felt-tip pen
Tape
Pushpin
Drill
3 mm, 4.5 mm, 9 mm and 10 mm Drill bit
20 mm Hole saw
Wire
Rubber mallet
Bushings
Accessory Users Information Manual
AII 38281 (0711)
Rubber bumper
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 3 of 25
Illustration of the HFL Installed on the Vehicle
INSTALLATION
1. Make sure you have the anti-theft code for the audio
2. Disconnect the negative cable from the battery.
Customer Information: The information in this installation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted bydo-it-yourselfers.
CONTROL UNITHFL HARNESS
SWITCH
HFL
3.
ROOF CONSOLE
LEFT LENS
4 RETAINING TABS
RIGHT LENS
4 RETAINING TABS
SHOP TOWEL
FLAT-TIP SCREWDRIVER
ROOF CONSOLE
RIGHT LENS
4 RETAINING TABS
LEFT LENS
4 RETAINING TABSSHOP
TOWEL
FLAT-TIP SCREWDRIVER
With long roof console
AII 38281 (0711)
With short roof console
system or the navigation system (if equipped).
SUB-HARNESS
left and right lens from the roof console.Disengage the eight retaining tabs and remove the
-
4 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
4. Open the sunglass holder.
5. Remove the two black screws and the two silver
ROOF CONSOLE
SUNGLASS HOLDEROpen.
VEHICLE CONNECTOR
2 SCREWS(Black) 2 SCREWS
(Silver)
ROOF CONSOLE
SUNGLASS HOLDEROpen.
VEHICLE CONNECTOR
2 SCREWS(Black) 2 SCREWS
(Silver)
6.remove the two sunvisor holders.
7.
8. Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.
9.
SUNVISOR HOLDER
Turn.
2 SUNVISOR HOLDERS
LEFT SUNVISORTurn rearward.
Push upward.
FLAT-TIP SCREWDRIVER
HOLDER
Push and hold tab.
Rotate toward the door.
VEHICLE CONNECTORDisconnect if equipped.
AII 38281 (0711)
With long roof console
With short roof console
While holding the retaining tab, push up on the left sunvisor holder and turn the left sunvisor back to its original position to remove it. Disconnect the vanity mirror light connector. If the retaining tab does not stay pushed in, return the sunvisor to its original
Turn each sunvisor holder 45 counterclockwise, and
Turn the left sunvisor toward the drivers door.
position and repeat steps 7 thru 9.
remove the roof console.Disconnect the three vehicle connectors and screws and let the roof console drop down.
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 5 of 25
10. Pull away the weatherstrip from the left front A-pillar trim.
11. Using a small rubber mallet and a shop towel, gently tap the left front A-pillar trim at the SIDE CURTAIN AIRBAG mark to release the clip. Go to step 14.
CLIP
FRONT A-PILLAR TRIM
FRONT A-PILLAR
PIN
STRIKE POINT
SHOP TOWEL
RUBBER MALLET
LEFT FRONT A-PILLAR TRIM
CLIPWEATHERSTRIP
12. Pull away the weatherstrip from the left front A-pillar trim.
13. Using a small rubber mallet and a shop towel, gently tap the left front A-pillar trim just below the SIDE CURTAIN AIRBAG mark to release the clip.
CLIP
FRONT A-PILLAR TRIM
FRONT A-PILLAR
PIN
STRIKE POINT
SHOP TOWEL
RUBBER MALLET
CLIPWEATHERSTRIP
LEFT FRONT A-PILLAR TRIM
AII 38281 (0711)
2-door model: Do steps 10 and 11. 4-door model: Do steps 12 and 13.
-
6 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
14.
15.
trim.
2 CLIPS
WEATHERSTRIP
LEFT FRONT A-PILLAR TRIM
CLIP (Discard.)
NEW CLIP
LEFT FRONT A-PILLAR TRIM
16. Remove the drivers dashboard lower cover (eight clips, two hooks, and disconnect the vehicle connector).
17.
8 CLIPS
DRIVERS DASHBOARD LOWER COVERVEHICLE
CONNECTOR
2 HOOKS
3 CLIPS
DRIVERS DASHBOARD UNDER COVER
PIN
AII 38281 (0711)
Remove and discard the clip on the left front A-pillar trim, and install a new clip (supplied) on the
Remove the left front A-pillar trim (two clips).
under cover (three clips and one pin).V6 Model only: Remove the drivers dashboard
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 7 of 25
18. Pull away the weatherstrip, then remove the left dashboard side cover (seven retaining tabs and three hooks).
19.
LEFT DASHBOARD SIDE COVER
7 RETAINING TABS
3 HOOKS
WEATHERSTRIP
SELF TAPPING SCREW
Unlock.KEY
TRUNK LID/FUEL FILL DOOR OPENER
4 RETAINING TABS
COVER
FRONT
2 HOOKS
20.clips and retaining tab) to remove the trim.
21.
FRONT
RETAINING TAB
LEFT FRONT DOOR SILL TRIM
4 CLIPS
2 CLIPS WEATHERSTRIP
LEFT KICK PANEL
AII 38281 (0711)
Remove the cover from the trunk lid/fuel fill door
lid/fuel opener is unlocked.
Pull up the front edge of the left front door sill trim (four
remove the self-tapping screw. Make sure the trunk opener (two hooks and four retaining tabs), then
panel (two clips).Pull away the weatherstrip, then remove the left kick
-
8 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
If the vehicle is an M/T model, continue with step 22; if not, go to step 24.
22.
counterclockwise.
23. Remove the center console panel (twelve clips and
SHIFT KNOB
2 RETAINING TABS
SHIFT BOOT
VEHICLE CONNECTOR
12 CLIPSCENTER CONSOLE PANEL
24. Remove the center console panel (twelve clips and disconnect the vehicle connector).
With navigation system, continue with step 25; Without navigation system go to step 28.
25. Place a shop towel as shown.
26. Remove the pocket (four bolts).
12 CLIPS
VEHICLE CONNECTOR
CENTER CONSOLE PANEL
POCKET
4 BOLTS SHOP TOWEL
AII 38281 (0711)
M/T Model
A/T Model
With Navigation SystemCounterclockwise
disconnect the vehicle connector). Go to step 25 or 28.
Remove the shift knob by turning it Push down on the shift boot (two retaining tabs).
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 9 of 25
27. Remove the compact disc changer (two bolts, two clips and disconnect the vehicle connector).
28. Place a shop towel as shown.
29. Remove the pocket (four bolts).
VEHICLE CONNECTOR
2 CLIPS
2 BOLTS
CHANGER
POCKET
4 BOLTS SHOP TOWEL
Installing the Control Unit and Routing the Harness
30. Using a scissors, cut out template A and template B.
Vehicle identification number: 1HG A
Vehicle identification number: JHM C
If the vehicle is equipped with a Long roof console, continue from step 30; if not, go to step 47.
TEMPLATE
TEMPLATE A
TEMPLATE B
TEMPLATE
TEMPLATE A
TEMPLATE B
AII 38281 (0711)
Without Navigation System
With long roof console
COMPACT DISC
LINE A
LINE B
-
10 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
31. Remove the sunglass holder from the roof console (one screw, one spacer and one spring).
32. Remove the roof console trim from the roof console (six retaining tabs).
SUNGLASS HOLDER
ROOF CONSOLE
SCREW(Discard.)
SPACER(Discard.)
SPRING
ROOF CONSOLE
ROOF CONSOLE TRIM
6 RETAINING TABS
33. Remove the console light from the roof console (four retaining tabs).
34.holder installation hole on the roof console with a
If the vehicle identification number is 1HG A ,
ROOF CONSOLE
CONSOLE LIGHT
4 RETAINING TABS
ROOF CONSOLE
DRILL BIT (9 mm)
AII 38281 (0711)
go to step 34; if not, go to step 35.
While wearing eye protection, enlarge the sunglass
position.9 mm drill bit. Make sure to drill at the correct
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 11 of 25
35.
36. Using a pushpin, mark the roof console as indicated on the template. Remove the template.
37.
TAPE
PUSHPIN
2 MARKS
TEMPLATE A
ROOF CONSOLE
Align.
DRILL BIT (4.5 mm)
2 MARKS
ROOF CONSOLE
38.
39. Using a pushpin, mark the roof console as indicated on the template. Using a felt-tip pen, mark the roof console around the template. Remove the template.
40. While wearing eye protection, drill the four marked locations to 20 mm. First drill with a 3 mm drill bit and finish with a 20 mm hole saw.
PUSHPIN
PUSHPIN
TAPE
4 MARKS
FELT-TIP PEN
TEMPLATE B
ROOF CONSOLE
20 mm HOLE SAW
4 MARKS
DRILL BIT (3 mm)
20 mm HOLE SAW
DRILL BIT (3 mm)
ROOF CONSOLE
AII 38281 (0711)
indicated position.Tape template A to the roof console at the
indicated position.Tape template B to the roof console at the
locations to 4.5 mm. Remove any burrs.While wearing eye protection, drill the two marked
-
12 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
41.the roof console in step 39. After cutting, remove any burrs.
42.console.
43.
Cut out.
Mark made in step 39.
ROOF CONSOLE
UTILITY KNIFE
2 DOUBLE-SIDED TAPES A
10 mm
CONTROL UNIT
10 mm
Remove the adhesive backing.
Remove the adhesive backing.
44.
45.
46. Using the holes drilled in step 37, secure the HFL bracket to the roof console. Go to step 67.
CENTER
CONTROL UNIT
ROOF CONSOLE
Remove the adhesive backing.
HFL HARNESS
HFL HARNESS 22-PIN CONNECTOR
ROOF CONSOLE
Holes drilled in step 37.
2 WASHER SCREWS, 4 x 12 mm
HFL BRACKET
ROOF CONSOLE
AII 38281 (0711)
Using an utility knife, cut along the mark made on
tape A at the position shown.from each double-sided tape A and attach thetapes A will attach. Remove the adhesive backing areas on the control unit where the double-sidedUsing isopropyl alcohol on a shop towel, clean the
Reinstall the console light and trim and unit to the roof
areas where the double-sided tapes A will attach.Using isopropyl alcohol on a shop towel, clean the
Remove the adhesive backing from the double-sided tape A and attach the control unit to the roof consoleas indicated.
control unit.Plug the HFL harness 22-pin connector into the
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 13 of 25
47. Using a scissors, cut out template A and template B.
48. Remove the sunglass holder from the roof console (two screws, two spacers and one spring).
TEMPLATE
TEMPLATE A
TEMPLATE B
SUNGLASS HOLDER
ROOF CONSOLE
SCREW(Discard.)
SPACER(Discard.)
SCREW(Discard.)
SPACER(Discard.)
SPRING
49. Remove the console light from the roof console (four retaining tabs).
Vehicle identification number: 1HG A
50.
If the vehicle identification number is 1HG A ,
ROOF CONSOLE
CONSOLE LIGHT
4 RETAINING TABS
ROOF CONSOLE
DRILL BIT (9 mm)
AII 38281 (0711)
With short roof console
LINE C
go to step 50; if not, go to step 53.
While wearing eye protection, enlarge the sunglass
position.a 9 mm drill bit. Make sure to drill at the correctholder installation hole on the roof console with
-
14 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
51. Measure and pierce six locations on the roof console with a pushpin as shown. Drill with a 3 mm
ROOF CONSOLEDRILL BIT
(3 mm 10 mm)
DRILL
PUSHPIN
5 mm
5 mm
5 mm5 mm
5 mm 5 mm 5 mm
5 mm
5 mm5 mm
5 mm
ROOF CONSOLE
CENTER
5 mm
52. Using a utility knife, cut along the marked line on the roof console as shown. Go to step 55.
Vehicle identification number:JHM C
53. Pierce six locations on the roof console with a
ROOF CONSOLE
UTILITY KNIFE
MARKED LINE
ROOF CONSOLE
Cut.
PUSHPIN
DRILL
DRILL BIT(3 mm 10 mm)
AII 38281 (0711)
pierced points. Then finish with a 10 mm drill bit.
with a 10 mm drill bit.drill bit at the six pierced points. Enlarge each hole
pushpin as shown. Drill with a 3 mm drill bit at the six
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 15 of 25
54. Using a utility knife, cut along the marked line on the roof console as shown.
55.
56. Using a pushpin, mark the roof console as indicated on the template. Remove the template.
ROOF CONSOLE
UTILITY KNIFE
MARKED LINE
Cut.
ROOF CONSOLE
TAPE
PUSHPIN
TEMPLATE A
ROOF CONSOLE
2 MARKS
Align.
57.
58.
59. Using a pushpin, mark the roof console as indicated on the template. Using a felt-tip pen, mark the roof console around the template. Remove the template.
DRILL BIT (4.5 mm)
2 MARKS
ROOF CONSOLE
PUSHPIN
PUSHPIN
TAPE
4 MARKS
FELT-TIP PEN
TEMPLATE B
ROOF CONSOLE
AII 38281 (0711)
locations to 4.5 mm. Remove any burrs.While wearing eye protection, drill the two marked
indicated position.Tape template B to the roof console at the
indicated position.Tape template A to the roof console at the
-
16 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
60. While wearing eye protection, drill the four marked
61.the roof console in step 59. After cutting, remove any burrs.
20 mm HOLE SAW
4 MARKS
DRILL BIT (3 mm)
20 mm HOLE SAW
DRILL BIT (3 mm)
ROOF CONSOLE
Cut out.
Mark made in step 59.
ROOF CONSOLE
UTILITY KNIFE
62.
63.
64.
2 DOUBLE-FACE TAPES A
10 mm
CONTROL UNIT
Remove the adhesive backing.
Remove the adhesive backing.
CENTER
CONTROL UNIT
CONTROL UNIT
Remove the adhesive backing.
HFL HARNESS HFL HARNESS 22-PIN CONNECTOR
ROOF CONSOLE
10 mm
40 mm
ROOF CONSOLE
AII 38281 (0711)
locations to 20 mm. First drill with a 3 mm drill bit, then finish with a 20 mm hole saw.
Using a utility knife, cut along the mark made on
areas where the double-sided tapes A will attach.Using isopropyl alcohol on a shop towel, clean the
Remove the adhesive backing from the double-sided tape A and attach the control unit to the roof console as indicated.
shown.
areas where the double-sided tapes A will attach.Using isopropyl alcohol on a shop towel, clean the
tape A and attach the double-sided tape A at the positionRemove the adhesive backing from each double-sided
control unit.Plug the HFL harness 22-pin connector into the
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 17 of 25
65.
66. With the two 4 x 12 mm washer screws and the holes drilled in step 57, secure the HFL bracket to the roof console.
Holes drilled in step 57.
2 WASHER SCREWS, 4 x 12 mm
HFL BRACKET
ROOF CONSOLE
Remove the adhesive backing.
DOUBLE-FACED TAPE B
Switch Installation
67. Bend the switch terminal as shown.
68. Insert the rubber bumper to the HFL retainer.
69. Assemble HFL retainer, switch, and HFL trim with four 3 x 10 mm self-tapping screws.
SWITCH
HFL TRIM
HFL RETAINER
4 SELF-TAPPING SCREWS, 3 x 10 mm
RUBBER BUMPER
HFL RETAINER
SPEAKER
45
SWITCH TERMINAL
BACKSIDE OF THE SWITCH
SWITCH TERMINALBend.
AII 38281 (0711)
With long roof console
Using isoplopyl alcohol on a shop towel, clean the
attach the double faced tape B to the HFL bracket.areas where the double-faced tape B will attach.
-
18 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
SWITCH
HFL TRIM
HFL RETAINER
4 SELF-TAPPING SCREWS, 3 x 10 mm
RUBBER BUMPER
HFL RETAINER
SPEAKER
45
SWITCH TERMINAL
SWITCH TERMINALBend.
70.console.
71.switch.
72.
SWITCH
HFLHARNESS
HFL HARNESS 20-PIN CONNECTOR
ROOF CONSOLE
SCREW, 3 x 10 mm (Black)
SELF-TAPPING SCREW, 3 x 10 mm (Black)
CONSOLE LIGHT
SWITCH
HFL HARNESS
HFL HARNESS 20-PIN CONNECTOR
ROOF CONSOLE
SELF-TAPPING SCREW, 3 x 10 mm (Black)
SELF-TAPPING SCREW, 3 x 10 mm (Black)
CONSOLE LIGHT
AII 38281 (0711)
With short roof console
With long roof console
With short roof console
SELF-TAPPING
BUSHING
BUSHING
BUSHINGBUSHING
BACK SIDE OF THE SWITCH
Reinstall the console light and trim to the roof
Connect the HFL harness 20-pin connector to the
Install the switch assembly in step 69 to the roof
two bushings.console with two self-tapping screws (Black) and
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 19 of 25
73.
74.
HFL
END OF THE CORRUGATED TUBE
2 EPT SEALERSCORRUGATED TUBE
HFL
WIRE TAPE
3-PIN CONNECTOR
LEFT FRONT PILLAR OPENING
VEHICLE BRACKET
DRIVERS DASHBOARD LOWER COVER OPENING
DRIVERS DASHBOARD UNDER COVER OPENING
75.
76.
77.
78.
WIRE TIE
VEHICLE HARNESS
LEFT FRONT A-PILLAR
VEHICLE CLIP
ROOF LINING
4 WIRE TIES
ROOF CONSOLE
OPENING
HFL
ROOF LINING
AII 38281 (0711)
SUB-HARNESS
HFL subharness around the corrugated tube.Wrap two EPT sealers on the HFL subharness
SUBHARNESS
Route the HFL subharness up the A-pillar, and align
Secure the HFL subharness to the vehicle harness
Secure the HFL subharness to the vehicle harness
SUBHARNESS
HFL SUBHARNESS
Attach a piece of wire to the subharness as shown. Route the subharness up the left front pillar trim opening. Remove the wire.
with four wire ties.
with one wire tie by the vehicle clip.
HFL SUBHARNESS
SUBHARNESSTAPE ON HFL GREEN
vehicle clip.the green tape on the HFL subharness with the
opening.Route the HFL subharness to the roof console
-
20 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
79.roof console opening, plug the HFL harness 3-pin
and secure the connector to the vehicle bracket with one wire tie.
80.eas where the EPT sealers will attach. Under the
panel with three EPT sealers.
WIRE TIE
Front
HFL HARNESS 3-PIN CONNECTOR
3-PIN CONNECTOR
ROOFCONSOLE
VEHICLE BRACKET
GREEN CONNECTOR
ROOF CONSOLE OPENING
ROOF PANEL
HFL
ROOF LINING
3 EPT SEALERS
81.
82.harness forward the fuse box as shown. Secure the
ties.
VEHICLE CONNECTORS
ROOF CONSOLE
2 SCREWS(Silver; Reuse.)
2 SCREWS(Black; Reuse.)
VEHICLE HARNESS
2 WIRE TIES
HFLSUBHARNESS
DRIVERS DASHBOARD LOWER COVER OPENING
FUSE BOX
AII 38281 (0711)
With an assistant holding the roof console near the
connector into the HFL subharness 3-pin connector,
HFL SUBHARNESS
Using isopropyl alcohol on a shop towel, clean the ar-
roof liner, secure the HFL subharness to the roof
HFL subharness to the vehicle harness with two wire
(silver) to reinstall the roof console.Reuse the two screws (black) and the two screwsPlug the vehicle connectors to the roof console.
Route the HFL subharness down along the vehicle
SUBHARNESS
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 21 of 25
83.fuse box.
Front view
Connection position
FUSE BOX
12-PIN CONNECTOR
FUSE BOX
FUSE BOX
12-PIN CONNECTOR
HFL DUMMY CONNECTOR
84. Remove the upper hood opener bolt, install the
85.with two wire ties.
UPPER HOOD OPENER BOLT(Discard.)
GROUND BOLT(Supplied.)
GROUND TERMINAL HOODOPENER
VEHICLE PANEL
HFL
VEHICLE HARNESS
VEHICLE HARNESS
GROUND TERMINAL
FUSE BOX
2 WIRE TIES
AII 38281 (0711)
Plug the HFL subharness12-pin connector into the
HFL SUBHARNESS
Secure the HFL subharness to the vehicle harness
and tighten the ground bolt.terminal into the upper hole of the hood opener,
SUBHARNESS
HFL SUBHARNESS
HFL SUBHARNESS
HFL SUBHARNESS
If another accessory is connected to the fuse box 12-pin connector, remove the dummy connector from the 12-pin connector of the other accessorys harness and connect the
the other accessorys harness.
SUBHARNESS
OTHER ACCESSORYS OTHER ACCESSORYS
HARNESS 12-PINCONNECTOR
HARNESS
ground bolt with the HFL subharness ground
12-pin connector of the HFL subharness to
-
22 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
86. Install the 2A fuse in the fuse box in the location shown.
87. Attach the HFL 2A fuse label to the kick panel at the location shown.
FUSE BOX
Connection position
FUSE BOX
2A FUSE
Front view
FUSE LABEL
2A FUSE LABEL
2A FUSE LABEL
88.
harness with three wire ties.
89.
harness with two wire ties.
3 WIRE TIES
HFL
VEHICLE HARNESS
VEHICLE HARNESS
FUSE BOX
2 WIRE TIES
HFL
VEHICLE HARNESS
STEERING TILT LEVER
STEERING SHAFT
AII 38281 (0711)
Route the HFL subharness along the vehicle harness as shown. Loosely secure it to the vehicle
SUBHARNESS
harness as shown. Loosely secure it to the vehicle Route the HFL subharness along the vehicle
SUBHARNESS
Loosely secure.
Loosely secure.
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 23 of 25
90.
91.
3 WIRE TIESLoosely
HFL
VEHICLE HARNESS
VEHICLE BRACKET
ACCELERATOR PEDAL
3 WIRE TIESLoosely tighten.
HFL
VEHICLE HARNESS
PARKING BRAKE
92. Disconnect the vehicle harness 1-pin connector, and
93.tie.
1-PIN CONNECTOR
VEHICLE 1-PIN CONNECTOR
VEHICLE HARNESS 1-PIN CONNECTOR
PARKING BRAKE
WIRE TIE
HFL PARKING BRAKE LEVER
AII 38281 (0711)
with three wire ties.
SUB-HARNESS
connect the HFL subharness 1-pin connector.
Route the HFL subharness along the vehicle Secure the HFL subharness connections with a wire
HFL SUBHARNESS
SUBHARNESS
secure.
harness. Loosely secure it to the vehicle harness
Route the HFL subharness as shown. Looselysecure it to the vehicle harness with three wire ties.
HFL SUBHARNESS CONNECTION
SUBHARNESS
-
24 of 25 2007 American Honda Motor Co., Inc. All Rights Reserved.
94. Tighten the three wire ties from step 91.
95. Tighten the three wire ties from step 90.
3 WIRE TIES
HFL
VEHICLE HARNESS
PARKING BRAKE LEVER
3 WIRE TIES
HFL
VEHICLE HARNESS
VEHICLE BRACKET
96.
97. Tighten the three wire ties from step 88.
WIRE TIE
HFL
VEHICLE HARNESS
VEHICLE HARNESS
HFL
WIRE TIE
STEERING TILT LEVER
STEERING COLUMN
3 WIRE TIES
HFL
VEHICLE HARNESS
AII 38281 (0711)
SUBHARNESS
SUBHARNESS
SUBHARNESS
Tighten the two wire ties from step 89.
SUBHARNESS
SUBHARNESS
-
2007 American Honda Motor Co., Inc. All Rights Reserved. 25 of 25
98.
99. Check that all wire harnesses are routed properly and all connectors are plugged in.
100. Reinstall all removed parts. Check that all clips and other fasteners are installed securely.
101. Reconnect the negative cable to the battery.
102. Enter the customers audio system or navigation sys-tem (if equipped) anti-theft code.
103. Reset the clock (for vehicles without navigation).
ROOF PANEL HOLE
LEFT SUNVISOR
LOCK
VEHICLE CONNECTORConnect if equipped.
AII 38281 (0711)
Reconnect the vanity mirror light connector, Insert the holder into the roof panel hole. Push up on the visor and rotate to its original position to lock it into place.
Button1: Button2: