Authorized Distributor:

Printed in U.S.A. © COPYRIGHT 1997 CARR LANE MANUFACTURING CO. 8304-897

ALPHA-NUMERICAL INDEX

BC Block Push Clamps..........................See websiteCS Clamp Straps .......................................50-51, 53DLT Diamond Locating Pins ...................................43EC Edge Clamps ...................................See websiteEX Extending Clamps............................See websiteF Distribution Manifolds ......................See websiteFAC Forged Adjustable Clamps ..............................58FH Fixture Hose ....................................................64HTC Horizontal Toggle Clamps ...............................63KSA Knob Shoe Assemblies ...................................62KSJ Knurled Screw Jacks.......................................46PC Push/Pull Toggle Clamps ................................63PD Pallet Decouplers ............................See websitePPC Push/Pull Toggle Clamps ................................63RLT Round Locating Pins .......................................43SA Standard-Adjustable Spindles .........................55SAC Serrated Adjustable Clamps ......................60-61SC Swing Clamps..................................See websiteSCH Swing Clamps..................................See websiteSHCS Socket-Head Cap Screws ...............................32SHS Swivel Head Screws........................................62SPC Push/Pull Toggle Clamps ................................63SSXX Toolroom Starter Sets ..................................8-13SSC Swivel Screw Clamps......................................62TSB Adjustable-Torque Thumb Screws ..................62TSJ Torque Screw Jacks........................................47V Sequence Valves.............................See websiteWS Work Supports .................................See website0001 Protection Plugs ..............................................330101 Precision Bushings............................................5010X Rectangular Tooling Plates, Regular...............14015X Rectangular Tooling Plates, Extra Long..........15020X Vertical Tooling Plates.....................................25030X Round Tooling Plates ......................................16040X Angle Plates, Tall ............................................27045X Angle Tooling Plates .......................................20050X Angle Plates, Short..........................................27060X Two-Sided Tooling Blocks...............................21065X Window Tooling Blocks ...................................24070X Four-Sided Tooling Blocks ..............................22080X Platform Tooling Plates ...................................19080X Square Pallet Tooling Plates ...........................17085X Rectangular Pallet Tooling Plates ...................18090X Riser Plates .....................................................26100X Pivoting Edge Clamps .....................................59110X Downthrust Backstops.....................................59125X Screw-Clamp Adaptors ...................................62141X Support Riser Blocks.......................................35146X Multipurpose Riser Blocks...............................3515XX Swing Clamp Assemblies................................56160X Clamp Riser Blocks .........................................34

165X Sideways Mounting Blocks..............................34180X Adjustable Swing Stops...................................48190X High-Rise Clamps, Adaptor Bases..................53200X High-Rise Clamps, Tapped-Nose....................52205X High-Rise Clamps, Standard-Nose .................52210X High-Rise Clamps, Gooseneck .......................52220X High-Rise Clamps, Tapped-Nose ...................54230X Narrow Riser Blocks........................................54235X Spacer Blocks .................................................54240X Support Holders ..............................................54250X Swivel Contact Bolts........................................55260X Contact-Bolt Extensions ..................................55290X Adjustable Stops .............................................4831XX Support Cylinders............................................40315X Relieved Support Cylinders.............................41320X Shoulder Support Cylinders ............................41330X Extension Supports .........................................36340X Heavy-Duty Screw Jacks ................................46350X Screw-Jack Tips ..............................................46360X Halfway Extension Supports ...........................37370X Edge Supports, Single.....................................39380X Edge Supports, Double ...................................39390X Spring-Stop-Button Adaptors ..........................49400X Locating Gages ...............................................33410X Locating-Pin Adaptors, Fixed ..........................42420X Locating-Pin Adaptors, Adjustable ..................42430X Locating Bushings ...........................................32430X Locating Screws ..............................................32431X Hex-Head Cap Screws....................................33450X Locating Pins, Round ......................................33460X Locating Pins, Diamond ..................................33475X Multipurpose Extension Supports....................37480X Screw Rest Pads.............................................4449XX Quick-Change Tooling Plates..........................23500X Hook Clamps, Long-Arm .................................57501X Hook Clamps, Tapped Long-Arm....................57510X Hook-Clamp Holders .......................................57520X Riser Cylinders ................................................38530X Up-Thrust Clamps ...........................................56540X Toggle-Clamp Adaptors ..................................6355XX Pallet Decoupler Adaptors ...............See website550X Clamp Adaptors ...............................See website550X Manifold-and-Valve Adaptors ..........See website550X Swing-Clamp Adaptors ....................See website550X Work Support Adaptors ...................See website561X Cam Edge Clamps ..........................................58570X Manual Work Supports....................................47600X Horizontal V Blocks .........................................45610X Vertical V Blocks .............................................447XXX Height Shims ...................................................38

ii

Page 1MF

(Rev. 8-94)

INTRODUCTIONWhat exactly is modular fixturing? In many ways modular fixturing isjust like permanent fixturing, except for a few key differences. First,modular fixtures can be assembled entirely from reusable off-the-shelfcomponents, without machining. Next, many modular components areadjustable and universal. Finally, specially designed tooling plates andblocks, with a standard grid pattern, are the foundation of a good mod-ular system.

A VALUABLE TOOL FOR EVERYMACHINE SHOP:Most metal-machining manufacturers have good applications for tem-porary fixturing every day! The leadtime and expense required to builda permanent fixture are often difficult to justify. This is especially truewhen production runs are small and do not repeat on a regular basis.General-purpose workholders — such as vises, chucks, and tablemounted clamps — can be ready for production on short notice, butthey are primarily suited for short runs of basic parts. Fortunately,there is now another alternative: modular fixturing. When a companyadds modular fixturing to its options, even job-shop-type productioncan benefit from quality fixturing.

GOOD APPLICATIONS FOR MODULARFIXTURING:Modular fixturing is an ideal answer to many workholding problems.One-time jobs, found especially in job shops, are ideal for modular fix-turing; with modular fixturing, a workholder can be economically builteven for a one-part run. Jobs that do not repeat on a regular basis arewell suited to modular fixturing; modular fixturing permits rapid setupof short-notice production runs. Modular fixturing is also ideal for pro-totype parts; since prototypes are often changed or redesigned, thecost of building a permanent fixture for each new variation would beprohibitive. Replacement parts are another perfect application; modu-lar fixturing allows a company to respond to orders as they arereceived, instead of shipping parts from an inventory. Trial fixturing isalso an excellent application; modular workholders allow a designer tofine tune tooling ideas before a final production workholder is built.Finally, modular fixturing is valuable while permanent fixtures are builtor repaired.

THE WIDEST SELECTION OF TOOLINGPLATES & BLOCKS:Tooling plates and blocks are the main structural elements of anymodular-fixturing system. The type, style, and number of plates andblocks available determine the variety of fixtures that can be built, andalso the number of machine tools that can be used. The Carr Lanemodular system has the largest selection of tooling plates and blocksavailable anywhere.

GRID HOLES VS. EARLIER T-SLOT SYSTEMS:The two primary forms of modular systems available today are thosewith grid-pattern holes and earlier types with T slots to mount compo-nents. Grid holes offer many advantages over T slots. Modular sys-tems with grid holes have greater positional accuracy and strengththan those with T slots. T-slot systems permit movement along theslot, so nothing but friction holds components in place. Wherever Tslots cross each other, a weak point exists.

MULTIPURPOSE GRID HOLES OFFERMAXIMUM FLEXIBILITY:Grid-pattern modular-fixturing systems come in two styles: those withalternating dowel holes and tapped holes and those with multipurposeholes. The alternating-hole style does not offer as many advantagesas the Carr Lane multipurpose-hole style. Multipurpose holes haveboth an alignment bushing and threaded insert in the same hole. Thisarrangement permits each hole to serve as an alignment hole, mount-ing hole, or both. Multipurpose holes are laid out in a standard 1" or 2"grid pattern (depending on the size) to allow the maximum number ofmounting locations.

POWER WORKHOLDING CAPABILITY:The ability to use hydraulic power workholding is another considera-tion in the selection of a modular-workholding system. A modular sys-tem should treat power workholding as an integral part of the completefixturing plan. Instead of requiring special power components, a goodmodular system uses standard, off-the-shelf power workholding com-ponents. Adapting standard power components to modular workhold-ers both reduces cost and expands design options. SWIFTSUREpower clamps and work supports are the finest available, and workhand-in-hand with the Carr Lane modular system. Also, our HILMAprecision hydraulic vises work perfectly with modular tooling platesand blocks.

CHOICE OF THREE SYSTEM SIZES:A good modular fixturing system needs to accommodate a wide rangeof workpiece sizes. Only Carr Lane offers a full line of modular compo-nents in three system sizes. As a comparison to choose the propersystem size, the table below shows typical clamping force exerted byclamp straps in each size (2-to-1 lever ratio).

SIZEMINI

STANDARDHEAVY

STUDSIZE

5/16-181/2-135/8-11

CLAMPINGFORCE(LBS)90023003700

RECOMMENDEDTORQUE(FT-LBS)

93877

Mini5/16-18

Standard1/2-13

Heavy5/18-11

Precision Bushing

LocatingScrew

Threaded Insert

Page 2MF

(Rev. 3-07)

PICTORIAL INDEX

TOOLING PLATES & BLOCKS

SUPPORTS & LOCATORS

Roundp. 16

Platformp. 19

Anglep. 20

Two-SidedBlocksp. 21

Locating Screwsand Bushings

p. 32

Socket-HeadCap Screws

p. 32

LocatingPinsp. 33

Hex-HeadCap Screws

p. 33

ProtectionPlugsp. 33

Edge Supportsp. 39

Locating-PinAdaptorsp. 42-43

Screw Rest Padsp. 44

V Blocksp. 44-45

Screw Jacksp. 46-47

Manual WorkSupports

p. 47

Four-SidedBlocksp. 22

Quick-Change Platesp. 23

Window ToolingBlocksp. 24

Vertical Platesp. 25

Riser Platesp. 26

Angle Platesp. 27

Rectangularp. 14-15

Square Palletp. 17

Rectangular Palletp. 18

LocatingGagesp. 33

SupportCylindersp. 40-41

Adjustable Stopsp. 48

Stop-Spring-ButtonAdaptors

p. 49

Clamp RiserBlocksp. 34

SidewaysMounting Blocks

p. 34

Support RiserBlocksp. 35

ExtensionSupportsp. 36-37

Riser Cylindersp. 38

HeightShimsp. 38

MOUNTING ACCESSORIES

Page 3MF

(Rev. 3-07)

PICTORIAL INDEX

CLAMPS

High-Rise Clampsp. 52-54

Contact Boltsp. 55

Double-End ClampStrapsp. 51

Swing Clamp Assembliesp. 56

Hook Clampsp. 57

Pivoting EdgeClamps

p. 59

Serrated AdjustableClampsp. 60-61

Cam EdgeClampsp. 58

Screw ClampAdaptors

p. 62

Fixture Hoseand Accessories

p. 64

ExtendingClamps

See website

Edge ClampsSee website

Block Push ClampsSee website

Swing ClampsSee website

DistributionManifolds

See website

PalletDecouplersSee website

Sequence ValvesSee website

Up-Thrust Clampsp. 56

POWER WORKHOLDING

Forged Adjustable Clampsp. 58

Toggle-Clamp Adaptorsp. 63

Power Unitsp. 64

Work SupportsSee website

Slotted-Heel ClampStrapsp. 50

Page 4MF

(Rev. 4-93)

Page 4MF

(Rev. 4-93)

TECHNICAL INFORMATION

MULTIPURPOSE HOLES

Mini

Standard

Heavy

Every multipurpose hole on a tooling plate or block has a precision alignment bushing on top, with a threaded insert below it. Multipurposeholes will accept Locating Screws, socket-head cap screws, studs, and many other threaded components. The proper mounting screw foreach component is listed in its table of dimensions. Locating screws are used to locate and fasten at the same time. Note: mini-size systemsuse a Locating Bushing together with a socket-head cap screw for extra strength, instead of a Locating Screw.

Page 5MF

(Rev. 8-98)

TECHNICAL INFORMATION

GRID ADDRESS SYSTEM

Mini Standard Heavy

The grid pattern of multipurpose holes on every tooling plateand tooling block face is labelled with letters in one directionand numbers in the perpendicular direction. Tooling-blockfaces are numbered (counterclockwise) with Roman numer-als. This allows recording the mounting-hole location ofeach component (e.g., A2, B3, D7, etc.) as part of perma-nent documentation. See the bill-of-material sheet on page9 as a sample.

Multipurpose holes are spaced within ±.0008 inches of trueposition on all tooling plates and blocks. The mini system iseven more accurate, with all holes spaced within ±.0004inches.

CUSTOM TOOLING PLATES

To build your own custom tooling plates with multipurpose mounting holes, we offerprecision bushings and threaded inserts separately. See hole locations and toler-ances above (holes must be jig bored), and page 4 for proper counterbore depth toinstall bushings. The threaded insert’s locking keys can be driven down by thebushing as it is pressed into the tooling plate.

PrecisionBushing

KeyInsert

SIZEMINI

STANDARDHEAVY

PART NO.CL-MF25-0101-02CL-MF40-0101-02CL-MF50-0101-02

OD.6247/.6244.8122/.8119.9060/.9056

ID.5003/.5005.5006/.5013.6256/.6263

SIZEMINI

STANDARDHEAVY

PART NO.CL-51618-KSCL-1213-KSCL-5811-KS

IDTHREAD5/16-181/2-135/8-11

ODTHREAD

1/2-133/4-167/8-14

LENGTH7/165/87/8

PRECISION BUSHINGS

KEY INSERTS

LENGTH.312.500.625

Page 6MF

(Rev. 3-07)

TECHNICAL INFORMATION

MOUNTING TOOLING PLATES ON T-SLOTTED TABLES

Standard and HeavyStandard and heavy Rectangular Tooling Plates areaccurately located on T-slotted tables using twoLocating Keys (page 166 of tooling-component catalogsection) in the center table slot. These plates are fas-tened to the machine table using four or six socket-head cap screws (page 32) and T Nuts (page 199 oftooling-component catalog section). Swivel Hoist Ringsare recommended for lifting large tooling plates (page32 of tooling-component catalog section).

Mini OnlyMini-size Rectangular Tooling Plates are accuratelylocated on T-slotted tables using two Sure-Lock FixtureKeys (page 165 of tooling-component catalog section)in the center table slot. These plates are normally fas-tened to the machine table using two or three socket-head cap screws (page 32) and T Nuts (page 199 oftooling-component catalog section). Alternatively, fourForged Adjustable Clamps (page 219 of tooling-component catalog section) can be used for greaterholding force.

Mini, Standard, and HeavyAll Rectangular Tooling Plates can be mounted asquick-change fixture plates on a subplate, as well asdirectly on a T-slotted machine table. Instead of theLocating Keys and Sure-Lock Fixture Keys used abovefor two-axis location, Subplate Locating Keys (page166 of tooling-component catalog section) are used forthree-axis location. A round key and a diamond(relieved) key are used together for precise locationwithout binding. The subplate hole pattern shown hereallows mounting any size and combination of standardor heavy Rectangular Tooling Plates, either lengthwiseor widthwise.

MOUNTING TOOLING PLATES ON SUBPLATES

Page 7MF

(Rev. 3-07)

TECHNICAL INFORMATION

MOUNTING TOOLING PLATES & BLOCKS ON PALLETS

JIS MountingJIS-type mounting is the most-common way to mounttooling plates and blocks on a machining-center pallet.Here the plate or block is located from two preciselyground reference edges at 90° to each other. The plateor block is pulled against the pallet's edge locatorsusing three socket-head cap screws (page 32) andalso fastened down with four to eight socket-head capscrews, depending on the size. Swivel Hoist Rings arerecommended for lifting tooling blocks and large toolingplates (page 32 of tooling-component catalog section).

DIN MountingMost of our modular tooling plates and blocks alsoincorporate DIN-mounting capability. Here the plate orblock is located using a center hole, and oriented usinga radial hole. Two Pallet Fixture Keys, a center pin anda radial pin, are required (page 167 of tooling-component catalog section). The plate or block is fas-tened down with four to eight socket-head cap screws,depending on the size.

Socket-HeadCap Screw

Edge Locator

Edge Locator Machine Pallet

Socket-HeadCap Screw

Socket-HeadCap Screws

Pallet FixtureKey (Radial)

Pallet FixtureKey (Center)

Machine Pallet

PALLETSIZE

320mm400mm500mm630mm800mm

PALLETCENTER-HOLE

DIA

50mm

PALLETRADIAL-HOLE

DIA

20mm

25mm

DISTANCE BETWEEN CENTER

AND RADIAL HOLES100mm150mm200mm200mm300mm

Page 8MF

(Rev. 3-07)

NUMBER OFSIZE PART NO. PIECESMINI CL-MF25-SS1B 533

STANDARD CL-MF40-SS1B 481HEAVY CL-MF50-SS1B 411

TOOLROOM STARTER SETS

ONE-FIXTURE SETS10% OFF INDIVIDUAL

PRICES WHEN ORDERED

IN THESE SETS!

BASIC STARTER SETEconomical starter sets to build one fixture at a time on a typicalmilling machine. This set includes matching sizes of our most-popularcomponents, plus all necessary mounting screws. Order a toolingplate and Locating Keys separately to fit specific machines. For acomplete listing of components, see pages 11-13.

Page 11MF

(Rev. 8-98)

HEAVY CL-MF50-2001 — 4 8 — —

HEAVY CL-MF50-1650 2 4 8 — —

HEAVY CL-MF50-2301 4 4 8 — —

HEAVY CL-MF50-2501 — 4 8 — —

HEAVY CL-MF50-1101 — 2 8 — —

STANDARD CL-MF40-1001 — 2 8 — —

HEAVY CL-MF50-1001 — 2 8 — —

STANDARD CL-MF40-2351 4 8 16 — —

Downthrust Backstops

Pivoting Edge Clamps

Screw-Jack Tips HEAVY CL-MF10-3501 — 1 1 — —

CL-MF40-3202 3 6 12 — —CL-MF40-3204 3 6 12 — —

STANDARD CL-MF40-3205 3 6 12 — —CL-MF40-3207 — — — 3 12CL-MF40-3208 — — — 3 12

CONTINUED ON NEXT PAGE

HEAVY CL-MF50-2351 4 8 16 — —

MINI — — — — — —

MINI — — — — — —

COMPONENTS IN STARTER SET

STANDARD — — — — — —

MINI CL-MF25-2001 — 4 8 — —

CL-MF25-1461 4 8 16 — —MINI CL-MF25-1462 4 8 16 — —

CL-MF50-1411 3 4 12 — —CL-MF50-1412 3 4 12 — —HEAVY CL-MF50-1413 3 4 12 — —CL-MF50-1414 — 4 12 — —

MINI CL-MF25-0900 — 1 1 — —

MINI CL-MF25-1251 3 3 12 — —

CL-MF25-1411 3 4 12 — —CL-MF25-1412 3 4 12 — —MINI CL-MF25-1413 3 4 12 — —CL-MF25-1414 — 4 12 — —

MINI CL-MF25-1650 2 4 8 — —

MINI CL-MF25-2301 4 8 8 — —

MINI CL-MF25-2351 4 8 16 — —

MINI CL-MF25-2502 — 4 8 — —

CL-MF25-3101 6 12 24 — —CL-MF25-3102 — 3 12 — —CL-MF25-3103 6 12 24 — —

MINI CL-MF25-3104 — 3 12 — —CL-MF25-3105 — 3 12 — —CL-MF25-3106 — 3 12 — —CL-MF25-3107 3 6 12 — —

CL-MF25-3200 6 12 24 — —CL-MF25-3202 — 6 12 — —MINI CL-MF25-3204 — 6 12 — —CL-MF25-3206 3 6 12 — —

CL-MF50-0501 — 2 4 — —HEAVY CL-MF50-0502 — 2 2 — —

STANDARD CL-MF40-1101 — 2 8 — —

STANDARD CL-MF40-1251 3 3 12 — —

CL-MF40-1411 3 4 12 — —CL-MF40-1412 3 4 12 — —STANDARD CL-MF40-1413 3 4 12 — —CL-MF40-1414 — 4 12 — —

CL-MF40-1462 4 8 16 — —STANDARD CL-MF40-1463 4 8 16 — —

STANDARD CL-MF40-1650 2 4 8 — —

STANDARD CL-MF40-2301 4 8 8 — —

STANDARD CL-MF40-2501 — 4 8 — —

CL-MF40-3101 3 6 12 — —CL-MF40-3102 3 6 12 — —CL-MF40-3103 3 3 12 — —CL-MF40-3104 — 3 12 — —STANDARD CL-MF40-3105 — 3 12 — —CL-MF40-3112 — 3 12 — —CL-MF40-3113 — 3 12 — —CL-MF40-3114 — 3 12 — —

SS

1B

SS

1C

SS

4C

SS

1P

SS

4P

QTY. IN SET*

MINI — — — — —

CL-MF40-0511 — 2 4 — —STANDARD CL-MF40-0512 — 2 2 — —

HEAVY CL-MF50-1463 4 8 16 — —

CL-MF50-3101 3 6 24 — —CL-MF50-3102 3 3 12 — —CL-MF50-3103 — 3 12 — —CL-MF50-3104 — 3 12 — —HEAVY CL-MF50-3112 3 6 24 — —CL-MF50-3113 — 3 12 — —CL-MF50-3114 — 3 12 — —CL-MF50-3115 — — — 3 6

CL-MF50-3202 3 6 12 — —HEAVY CL-MF50-3204 3 6 12 — —

STANDARD — — — — —

HEAVY — — — — — —

MINI — — — — — —

MINI — — — — — —

STANDARD CL-MF40-2001 — 4 8 — —

CL-MF25-2051 4 4 8 — —MINI CL-MF25-2052 — 4 8 — —

STANDARD CL-MF40-2101 4 4 8 — —

HEAVY — — — — — —

MINI — — — — — —

* No substitutions please.

CL-MF25-3301 2 3 12 — —CL-MF25-3302 — 3 12 — —MINI CL-MF25-3303 2 3 12 — —CL-MF25-3305 2 3 12 — —

CL-MF25-3601 4 4 16 — —MINI CL-MF25-3603 — 4 16 — —

CL-MF25-3605 — 4 16 — —

CL-MF40-3300 2 3 12 — —STANDARD CL-MF40-3301 2 3 12 — —

CL-MF40-3302 2 3 12 — —

CL-MF40-3401 — 1 1 — —STANDARD CL-MF40-3402 — 1 1 — —

CL-MF40-3403 — 1 1 — —

STANDARD CL-MF40-3601 3 3 12 — —

CL-MF50-3301 2 3 12 — —HEAVY CL-MF50-3302 2 3 12 — —

CL-MF50-3401 — 1 1 — —HEAVY CL-MF50-3402 — 1 1 — —

Heavy-Duty Screw Jacks CL-MF50-3403 — 1 1 — —

Halfway Extension Supports HEAVY CL-MF50-3602 4 4 16 — —

STANDARD CL-MF10-3501 — 1 1 — —

CL-MF25-3700 4 4 16 — —MINI CL-MF25-3702 — 4 16 — —CL-MF40-3702 2 4 8 — —CL-MF40-3704 — 4 8 — —CL-MF40-3705 2 4 8 — —STANDARD CL-MF40-3707 — — — 2 8CL-MF40-3708 — — — 2 8CL-MF40-3709 — — — 2 4

CL-MF50-3702 2 4 8 — —HEAVY CL-MF50-3704 2 4 8 — —

CL-MF50-3708 — — — 2 4

TOOLROOM STARTER SETS

HEAVY CL-MF50-1251 3 3 12 — —

HEAVY CL-MF50-2101 4 4 8 — —

CL-MF25-2601 — 4 8 — —MINI CL-MF25-2602 — 4 8 — —

CL-MF25-2603 — 4 8 — —

MINI CL-MF25-2901 2 4 8 — —

CL-MF25-3152 — 3 12 — —MINI CL-MF25-3154 — 3 12 — —

CL-MF40-2601 — 4 8 — —STANDARD CL-MF40-2602 — 4 8 — —

CL-MF40-2603 — 4 8 — —

STANDARD CL-MF40-2901 2 4 8 — —

CL-MF40-3152 3 3 12 — —STANDARD CL-MF40-3154 — 3 12 — —

CL-MF40-3155 3 3 12 — —

CL-MF50-2601 — 4 8 — —HEAVY CL-MF50-2602 — 4 8 — —

CL-MF50-2603 — 4 8 — —

CL-MF50-3153 3 3 12 — —HEAVY CL-MF50-3155 3 3 12 — —

Adjustable Stops HEAVY CL-MF50-2901 2 4 8 — —

Support Cylinders

Support Riser Blocks

Extension Supports

Edge Supports, Single

Shoulder Support Cylinders

Contact-Bolt Extensions

Angle Plates

Riser Plates

Spacer Blocks

Screw-Clamp Adaptors

Multipurpose Riser Blocks

Sideways Mounting Blocks

High-Rise Clamps, Tapped-Nose

High-Rise Clamps, Standard-Nose

Narrow Riser Blocks

High-Rise Clamps, Gooseneck

Swivel Contact Bolts

Relieved Support Cylinders

CL-1A-CR 8 12 32 — —MINI CL-1B-CR 8 12 32 — —

CL-6-CR 4 6 16 — —Clamp Rests HEAVY CL-7-CR 4 6 16 — —

Forged Adjustable Clamps HEAVY CL-10-FAC 4 4 16 — —

STANDARD CL-8-FAC 4 4 16 — —

STANDARD CL-MF40-5701 1 2 8 — —

Page 12MF

(Rev. 8-97)

Cam Edge Clamps HEAVY — — — — — —

Horizontal V Blocks HEAVY CL-MF50-6002 2 4 8 — —

CL-8-CS 4 6 16 — —STANDARD CL-10-CS 4 6 16 — —

CL-30-CS 2 2 8 — —CL-16-CS 4 6 16 — —

HEAVY CL-18-CS 4 6 16 — —CL-33-CS 2 2 8 — —

Manual Work Supports HEAVY CL-MF50-5701 1 2 8 — —

Swing-Clamp Adaptors HEAVY CL-MF50-5502 — — — 4 8

Clamp Adaptors HEAVY CL-MF50-5501 — — — 4 12

CL-MF50-5002 — 6 24 — —Hook Clamps HEAVYCL-MF50-5014 4 6 24 — —

CONTINUED FROM PRECEDING PAGE

MINI — — — — — —

Locating Bushings HEAVY — — — — — —

STANDARD CL-9-KSA 3 3 12 — —MINI CL-4-KSA 3 3 12 — —

CONTINUED ON NEXT PAGE

MINI — — — — — —

CL-1A-CS 8 12 32 — —MINI CL-1B-CS 8 12 32 — —

CL-23D-CS 2 4 8 — —

MINI — — — — — —

MINI CL-MF25-5401 4 6 16 — —

STANDARD CL-MF40-5301 — 4 12 — —

STANDARD CL-MF40-5401 4 6 16 — —

STANDARD CL-MF40-5501 — — — 4 12

Toggle-Clamp Adaptors HEAVY — — — — — —MINI — — — — — —

HEAVY — — — — — —Up-Thrust Clamps

CL-MF25-5201 4 6 16 — —MINI CL-MF25-5203 4 6 16 — —

CL-MF50-5201 4 6 16 — —Riser Cylinders HEAVY CL-MF50-5203 — 6 6 — —

CL-MF50-5204 4 6 6 — —

CL-MF40-5201 4 6 16 — —STANDARD CL-MF40-5203 — 6 6 — —

CL-MF40-5204 4 6 6 — —

CL-MF40-5101 4 6 24 — —STANDARDCL-MF40-5102 4 6 24 — —

MINI — — — — — —

STANDARD CL-MF40-6002 2 4 16 — —

MINI CL-MF25-5611 3 3 12 — —

STANDARD CL-MF40-5508 — — — 2 8Manifold-and-Valve Adaptors HEAVY CL-MF50-5508 — — — 2 8

CL-MF40-5504 — — — 4 12STANDARD CL-MF40-5505 — — — 2 8

CL-MF40-5507 — — — 2 2Work-Support Adaptors HEAVY CL-MF50-5507 — — — 2 4

CL-MF50-7002 — 10 10 — —CL-MF50-7003 — 10 10 — —CL-MF50-7004 — 10 10 — —

HEAVY CL-MF50-7005 — 10 10 — —CL-MF50-7010 — 10 10 — —CL-MF50-7020 — 10 10 — —CL-MF50-7062 — 10 10 — —CL-MF50-7125 — 10 10 — —

Flat Washers HEAVY CL-3-FW 4 6 16 — —

Jam Nuts HEAVY CL-10-JN 4 6 16 — —

MINI CL-MF25-5701 2 4 8 — —

CL-MF25-6001 2 4 16 — —MINI CL-MF25-6002 2 4 16 — —

CL-MF25-7002 — 10 10 — —CL-MF25-7003 — 10 10 — —CL-MF25-7004 — 10 10 — —

MINI CL-MF25-7005 — 10 10 — —CL-MF25-7010 — 10 10 — —CL-MF25-7020 — 10 10 — —CL-MF25-7062 — 10 10 — —CL-MF25-7125 — 10 10 — —

STANDARD CL-MF40-5502 — — — 4 8

STANDARD CL-MF40-5611 3 3 12 — —

CL-MF40-7002 — 10 10 — —CL-MF40-7003 — 10 10 — —CL-MF40-7004 — 10 10 — —

STANDARD CL-MF40-7005 — 10 10 — —CL-MF40-7010 — 10 10 — —CL-MF40-7020 — 10 10 — —CL-MF40-7062 — 10 10 — —CL-MF40-7125 — 10 10 — —

CL-4-CR 4 6 16 — —STANDARDCL-5-CR 4 6 16 — —

STANDARD CL-2-FW 4 6 16 — —

CL-450-HTC 4 6 16 — —STANDARD

CL-550-HTC — 4 16 — —

STANDARD CL-8-JN 4 6 16 — —

MINI CL-14-FW 8 12 32 — —

MINI CL-450-HTC 4 6 16 — —

MINI CL-5-JN 8 12 32 — —

MINI — — — — — —

MINI — — — — — —

Horizontal Toggle Clamps HEAVY — — — — — —

CL-MF40-4801 — 3 12 — —CL-MF40-4803 — 3 12 — —CL-MF40-4804 — 3 12 — —STANDARDCL-MF40-4805 3 6 12 — —CL-MF40-4807 — 6 12 — —CL-MF40-4808 3 6 12 — —

CL-MF40-4311 8 16 24 — —STANDARD CL-MF40-4312 4 8 8 — —

CL-MF40-4313 4 8 8 — —

CL-MF25-4101 1 4 8 — —CL-MF25-4102 1 4 8 — —MINI CL-MF25-4103 1 4 8 — —CL-MF25-4104 1 4 8 — —CL-MF40-4102 1 2 4 — —CL-MF40-4103 1 2 4 — —CL-MF40-4105 1 2 4 — —STANDARD CL-MF40-4112 — — — 2 2CL-MF40-4114 — — — 2 2CL-MF40-4116 — — — 2 2

MINI CL-MF25-4300 36 78 242 — —

CL-MF40-4202 1 2 4 — —STANDARD CL-MF40-4203 1 2 4 — —

CL-MF40-4205 1 2 4 — —CL-MF50-4202 1 2 4 — —

HEAVY CL-MF50-4203 1 2 4 — —Adjustable Locating-Pin Adaptors CL-MF50-4205 1 2 4 — —

STANDARD — — — — — —

CL-MF25-4311 4 12 24 — —MINI CL-MF25-4312 8 20 32 — —

CL-MF25-4313 4 8 8 — —

CL-MF50-4301 20 43 116 — —Locating Screws HEAVY CL-MF50-4302 15 52 124 3 6

CL-MF50-4303 — 3 12 8 16

CL-MF40-4301 34 74 140 — —STANDARD CL-MF40-4302 12 58 172 6 24

CL-MF40-4303 8 16 32 24 64

CL-MF50-4803 — 3 12 — —CL-MF50-4804 — 3 12 — —CL-MF50-4805 — 3 12 — —HEAVY CL-MF50-4806 3 6 24 — —CL-MF50-4807 — 3 12 — —CL-MF50-4808 3 6 24 — —

CL-MF25-4801 — 6 24 — —CL-MF25-4803 6 12 24 — —CL-MF25-4804 — 6 24 — —MINI CL-MF25-4805 6 12 24 — —CL-MF25-4806 — 6 24 — —CL-MF25-4807 6 12 24 — —

STANDARD CL-MF40-4751 2 2 8 — —MINI CL-MF25-4751 2 2 8 — —

CL-MF50-5101 4 6 24 — —Hook-Clamp Holders HEAVY CL-MF50-5102 4 6 24 — —

CL-MF25-5002 6 8 24 — —MINI CL-MF25-5013 6 8 24 — —

MINI CL-MF25-5101 6 8 24 — —

CL-MF40-5002 — 6 24 — —STANDARD CL-MF40-5013 4 6 24 — —

MINI — — — — — —

CL-MF50-4102 1 2 4 — —HEAVY CL-MF50-4103 1 2 4 — —

CL-MF50-4105 1 2 4 — —

CL-MF50-4311 8 12 24 — —HEAVY CL-MF50-4312 4 4 8 — —

CL-MF50-4313 4 4 8 — —

Multipurpose Extension Supports HEAVY CL-MF50-4751 2 2 8 — —

Knob Shoe Assemblies HEAVY CL-11-KSA 3 3 12 — —

CL-MF40-3802 — 2 4 — —CL-MF40-3804 — 2 4 — —CL-MF40-3805 — 2 4 — —STANDARD CL-MF40-3807 — — — 2 4CL-MF40-3808 — — — 2 4CL-MF40-3809 — — — 2 4CL-MF50-3802 — 2 4 — —

HEAVY CL-MF50-3804 — 2 4 — —CL-MF50-3808 — — — 2 4

MINI CL-MF25-3901 2 4 16 — —CL-MF40-3902 2 2 8 — —

STANDARD CL-MF40-3904 — 2 8 — —Spring-Stop-Button Adaptors HEAVY CL-MF50-3903 2 2 8 — —

CL-MF25-3800 2 3 12 — —MINI CL-MF25-3802 — 3 12 — —

Edge Supports, Double

Locating-Pin Adaptors

Hex-Head Cap Screws

Screw Rest Pads

Height Shims

Clamp Straps

Page 13MF

(Rev. 3-06)

STANDARD CLR-100-BC — — — 3 12

STANDARD CLR-102-GA — — — 1 4

CLR-9-FH — — — 3 12CLR-12-FH — — — 3 12

HEAVY CLR-15-FH — — — 3 12CLR-18-FH — — — 3 12CLR-24-FH — — — 3 12

CLR-311-SC — — — 4 8STANDARD CLR-321-SC — — — 4 8

HEAVY CLR-102-GA — — — 1 4

CL-5/16-18X3.00-STUD 8 12 32 — —MINI CL-5/16-18X3.50-STUD 8 12 32 — —CL-1/2-13X4.00-STUD 4 6 16 — —STANDARD CL-1/2-13X5.50-STUD 4 6 16 — —CL-5/8-11X4.50-STUD 4 6 16 — —HEAVY CL-5/8-11X5.50-STUD 4 6 16 — —

CL-50-SAC — 4 12 — —STANDARD CL-55-SAC 3 4 12 — —

CL-00-SAC — 4 12 — —MINI CL-5-SAC 3 4 12 — —

HEAVY — — — — — —

Spherical Nuts & Washers HEAVY CL-4-SNW 4 6 16 — —

HEAVY — — — — — —

CL-6-32X.50-SHCS 4 8 32 — —CL-10-32X.50-SHCS 28 90 204 6 24CL-1/4-20X.62-SHCS 16 24 64 — —CL-1/4-20X.75-SHCS 4 8 32 — —CL-1/4-20X2.00-SHCS — — — 14 56CL-5/16-18X.62-SHCS — 16 64 — —CL-5/16-18X.75-SHCS — 12 32 — —CL-5/16-18X1.00-SHCS — — — 4 4CL-5/16-18X1.50-SHCS — — — 12 48

STANDARD CL-5/16-18X2.00-SHCS — — — 16 32CL-5/16-18X3.50-SHCS — — — 8 16CL-1/2-13X1.00-SHCS 8 8 32 — —CL-1/2-13X1.25-SHCS 43 66 208 20 56CL-1/2-13X1.50-SHCS 43 62 208 20 56CL-1/2-13X1.75-SHCS 34 62 160 4 12CL-1/2-13X2.00-SHCS 6 38 120 6 20CL-1/2-13X2.25-SHCS 8 37 130 16 50CL-1/2-13X2.75-SHCS 8 17 60 14 26CL-1/2-13X4.50-SHCS 4 8 16 — —

CONTINUED FROM PRECEDING PAGE

CL-10A-SSB — 2 8 — —CL-20A-SSB — 2 8 — —CL-30A-SSB — 2 8 — —HEAVY CL-10C-SSB 2 2 8 — —CL-20C-SSB 2 2 8 — —CL-30C-SSB 2 2 8 — —

CL-12314-SA 4 6 24 — —STANDARD CL-38314-SA — 14 48 — —

CL-516212-SA 8 12 32 — —

CL-6-32X.50-SHCS 8 16 64 — —CL-1/4-20X.62-SHCS 16 24 64 — —CL-5/16-18X.62-SHCS 23 30 104 — —CL-5/16-18X.75-SHCS 25 60 200 — —CL-5/16-18X1.00-SHCS 33 58 192 — —

MINI CL-5/16-18X1.12-SHCS 57 139 388 — —CL-5/16-18X1.38-SHCS 34 72 216 — —CL-5/16-18X1.50-SHCS 20 37 148 — —CL-5/16-18X1.75-SHCS — 4 4 — —CL-5/16-18X2.00-SHCS — 8 24 — —CL-5/16-18X2.50-SHCS 4 16 40 — —

CL-6-32X.50-SHCS 4 8 32 — —CL-10-32X.50-SHCS 26 68 156 3 6CL-10-32X1.50-SHCS — — — 4 16CL-1/4-20X.75-SHCS 4 8 32 — —CL-1/4-20X2.00-SHCS — — — 8 32CL-5/16-18X1.00-SHCS — — — 4 8CL-5/16-18X2.50-SHCS — — — 18 72CL-5/16-18X3.50-SHCS — — — 8 16

HEAVY CL-3/8-16X4.00-SHCS — — — 8 16CL-5/8-11X1.00-SHCS — — — 4 16CL-5/8-11X1.25-SHCS 26 35 108 16 40CL-5/8-11X1.50-SHCS 40 59 188 4 16CL-5/8-11X2.00-SHCS 63 96 288 20 48CL-5/8-11X2.25-SHCS 6 16 48 2 4CL-5/8-11X2.50-SHCS 10 27 92 16 32CL-5/8-11X3.00-SHCS 6 26 86 6 12CL-5/8-11X5.00-SHCS 4 8 16 — —

MINI CL-51618-TSJN 2 4 8 — —

HEAVY CL-58438-SA 4 6 24 — —

CL-10A-SSB — 2 8 — —CL-20A-SSB — 2 8 — —CL-30A-SSB — 2 8 — —STANDARD CL-10C-SSB 2 2 8 — —CL-20C-SSB 2 2 8 — —CL-30C-SSB 2 2 8 — —

CL-516212-SA 8 12 32 — —MINI CL-38314-SA — 3 8 — —

CL-90-SAC — 4 12 — —HEAVY CL-95-SAC 3 4 12 — —

Clamp Springs HEAVY CL-11-SPG 8 12 32 — —

STANDARD CL-3-SNW 4 6 16 — —

STANDARD CL-9-SPG 8 12 32 — —

MINI CL-7A-SLP-1 — 4 16 — —

MINI CL-9-SNW 8 12 32 — —

MINI CL-6-SPG 16 24 64 — —

STANDARD — — — — — —Spring Locating Pins HEAVY — — — — — —

CL-10A-SSB 2 4 16 — —MINI CL-10C-SSB 2 4 16 — —

STANDARD CL-1213-TSJN 2 2 8 — —HEAVY CL-5811-TSJN 2 2 8 — —

CLR-200-F — — — 1 4CLR-202-F — — — 1 4CLR-301-F — — — 2 8CLR-303-F — — — 4 16CLR-304-F — — — 2 8STANDARD CLR-402-F — — — 6 24CLR-403-F — — — 4 16CLR-404-F — — — 4 16CLR-501-F — — — 4 16CLR-814-F — — — 6 24CLR-200-F — — — 1 4CLR-202-F — — — 1 4CLR-301-F — — — 2 8CLR-303-F — — — 4 16CLR-304-F — — — 2 8HEAVY CLR-402-F — — — 6 24CLR-403-F — — — 4 16CLR-404-F — — — 4 16CLR-501-F — — — 4 16CLR-814-F — — — 6 24

MINI — — — — — —

CLR-9-FH — — — 3 12CLR-12-FH — — — 3 12

STANDARD CLR-15-FH — — — 3 12CLR-18-FH — — — 3 12CLR-24-FH — — — 3 12

Block Push Clamps HEAVY CLR-300-BC — — — 3 12

MINI — — — — — —

CLR-402-CB — — — 3 12HEAVY CLR-405-CB — — — 2 4

MINI — — — — — —

CLR-109-CB — — — 4 12STANDARD CLR-400-CB — — — 3 12

CLR-405-CB — — — 4 12

CLR-121-WS — — — 2 2STANDARD CLR-201-WS — — — 4 12

CLR-410-WS — — — 2 8

MINI — — — — — —

HEAVY CLR-440-V — — — 2 8

MINI — — — — — —

MINI — — — — — —

CLR-511-SC — — — 4 8HEAVYCLR-521-SC — — — 4 8

MINI — — — — — —

MINI — — — — — —

CLR-720-EX — — — 4 8

STANDARD CLR-110-EC — — — 3 12Edge Clamps HEAVY CLR-310-EC — — — 3 12

MINI — — — — — —

Work Supports HEAVY CLR-121-WS — — — 2 4

MINI — — — — — —

MINI — — — — — —

MINI — — — — — —

STANDARD CLR-720-EX — — — 4 8

CLR-104-F — — — 1 4Distribution Manifolds HEAVY CLR-106-F — — — 1 4

STANDARD CLR-2-FL — — — 2 2

STANDARD CLR-72-H — — — 1 4

STANDARD CLR-9425-012-PD — — — 1 4

STANDARD CLR-440-V — — — 2 8

CLR-104-F — — — 1 4STANDARDCLR-106-F — — — 1 4

Hydraulic Fluid HEAVY CLR-2-FL — — — 2 2

Heavy-Duty Hose HEAVY CLR-72-H — — — 1 4

HEAVY CLR-9425-012-PD — — — 1 4

MINI — — — — — —

MINI — — — — — —STANDARD CL-350-SPC — 3 8 — —MINI — — — — — —

MINI CL-0-KSJ 2 4 8 — —STANDARD CL-7-KSJ 2 2 8 — —

MINI CL-200-PC — 3 8 — —STANDARD CL-200-PC — 3 8 — —

HEAVY CL-10-KSJ 2 2 8 — —

CL-450-VTC 4 6 16 — —STANDARD CL-650-VTC — 4 16 — —

Vertical Toggle Clamps HEAVY — — — — — —

MINI CL-450-VTC 4 6 16 — —

Knurled Check Nuts

Spring Stop Buttons

Push/Pull Toggle Clamps

Socket-Head Cap Screws

Push/Pull Toggle Clamps

Pallet Decouplers

Fixture Hose

Fittings

Contact BoltsSerrated Adjustable Clamps

Studs

Sequence Valves

Swing Clamps

Gauges

Knurled Screw Jacks

Standard Adjustable Spindles