2004 HUMMER H2 Navigation System Mgmhummer.com/hummerspecs/2004H2_nav_system.pdf · Navigation...

Overview ........................................................ 1-1Overview .................................................. 1-2

Features and Controls ..................................... 2-1Features and Controls ................................ 2-2

Navigation Audio System ................................ 3-1Navigation Audio System ............................ 3-2

Index ................................................................ 1

2004 HUMMER H2 Navigation System M

GENERAL MOTORS, GM, the GM Emblem, Hummerand the name Hummer are registered trademarksand H2 is a trademark of General Motors Corporation.

The information in this manual supplements theowner manual. This manual includes the latestinformation available at the time it was printed. Wereserve the right to make changes in the product afterthat time without notice.

Please keep this manual with the owner manual in yourvehicle, so it will be there if you ever need it whileyou are on the road. If you sell your vehicle, leave thismanual and the owner manual with the vehicle.

Part No. 15200265 A First Edition ©Copyright General Motors Corporation 08/01/03All Rights Reserved

ii

Overview .........................................................1-2Introduction ...................................................1-2Screen Setup .................................................1-4

Section 1 Overview

1-1

OverviewIntroduction

1-2

A. Power/Volume Knob. See Navigation SystemScreen on page 2-4.

B. NAV RPT (Navigation Repeat) Key. See NavigationSystem Screen on page 2-4.

C. NAV (Navigation) Key. See Navigation SystemScreen on page 2-4.

D. BAND Key. See “Playing the Radio” underNavigation Audio System on page 3-2.

E. SEEK Key. See “Finding a Station” under NavigationAudio System on page 3-2.

F. CD Key. See “Playing CDs” under Navigation AudioSystem on page 3-2.

G. Audio Key. See “Audio Screen” under NavigationAudio System on page 3-2.

H. CONFIG (Configuration) Key. See Screen Setupon page 1-4.

I. Navigation Joystick. See “Navigation Joystick”following in this section.

J. DVD/CD Eject Button. See “Playing CDs” underNavigation Audio System on page 3-2.

K. Navigation Screen. See Screen Setup on page 1-4and Navigation System Screen on page 2-4.

L. DVD/CD Loading SlotM. Map Key. See “Hard Keys” under Using the

Navigation System on page 2-2.

N. DEST (Destination) Key. See “Hard Keys” underUsing the Navigation System on page 2-2.

O. Menu Key. See “Hard Keys” under Using theNavigation System on page 2-2.

P. Zoom In Key. See “Hard Keys” under Using theNavigation System on page 2-2.

Q. Zoom Out Key. See “Hard Keys” under Using theNavigation System on page 2-2.

R. Back Key. See “Hard Keys” under Using theNavigation System on page 2-2.

Before you begin to operate the navigation system, readthis manual thoroughly to become familiar with it andto understand how the system works.

The navigation system allows you to do the following:

• Plan a route with provided turn-by-turn routeand map guidance with voice prompts.

• Select a destination using various methods andchoices.

• Receive broadcast announcements on traffic andemergency alert communications.

The information in the system may not always becomplete. Road conditions such as prohibited turns,detours, and construction zones, change frequently. It isimportant to consider whether you can follow thedirections given by the system for the current conditions.

1-3

Navigation JoystickThe navigation joystick, located on the bottom leftcorner of the navigation system, is used to makeselections in the navigation system. See the navigationsystem overview shown previously for more informationon location.

Move the joystick to the left, right, up, down, ordiagonally to move around the screens, and press thecenter of the joystick to enter a selection.

Screen Setup

CONFIG (Configuration) Key: Press the CONFIG keylocated to the left of the navigation screen, to accessthe Setup menu.

The Setup menu allows you to adjust such things asscreen color, appearance, and language of the displayfor the navigation system.

See “Hard Keys” under Using the Navigation System onpage 2-2 for more information on hard key functions.

1-4

Contrast/BrightnessTo adjust the contrast or brightness of the navigationscreen, choose the desired option by selecting it with thejoystick. Use the joystick to raise or lower the contrastor brightness to the desired level. You will see thescreen change as you adjust the contrast or brightness.

Screen ColorWhen the headlamp switch is turned off, the navigationscreen will change to a lighter background andchange colors, for better viewing in the daytime. Atnight, the screen will go to a darker background. Youcan select Auto for automatic adjustment.

You can also select day or night mode regardless of thelighting conditions. The Day setting leaves the systemin the day mode. The Night setting leaves the system inthe night mode.

BeepWith this feature On, a beep will sound every time a keyis pressed on the navigation system. Choose Off ifyou do not want to hear a beep whenever a keyis pressed.

LanguageYour vehicle has been set for the English language, butyou may also select French for all instructional textand voice prompts. However, names on the locationmap when using the navigation functions will notchange.

If your vehicle is equipped with a Driver InformationCenter (DIC), the navigation system will use thelanguage selected through the vehicle’s DIC.

If you wish to change the language, the map DVD mustbe inserted. Then, do the following:

1. Press the Language key under the Setup Menu.A caution will display.

2. Using the joystick, scroll to the desired languageand press the joystick to select it.

3. Select NEXT to change the display back to the mapscreen.

If the language is changed from English, the menuscreens will not match word-for-word as they appear inthis manual.

Every 50 ignition cycles a language screen willautomatically appear prompting you to choose alanguage. Select a language, then press NEXT.

1-5

Display OffTo turn the navigation screen off, press the Disp. OFFkey. To turn the screen back on, press any hardkey to the left of the navigation screen.

Voice Volume

This system has voice guidance prompts that providevarious messages as you approach points whereyou need to maneuver your vehicle, such as anintersection.

To adjust the volume of the voice prompts you receivefrom the system, do the following:

1. Press the menu key.

2. Select Voice Volume.

3. Use the joystick to raise or lower the volume. Thevoice prompt will come on with each adjustment togive you an idea of the volume at each level.

4. Once you have reached the desired volume level,press the back key to return to the previous screen.

With Adaptive voice volume control, the volume of voiceprompts will increase automatically once the vehicleexceeds 50 mph (80 km/hr). Select On to activate thisfeature.

If you do not need voice guidance, you may also selectOff to turn the prompts off.

1-6

Adjust Clock

To adjust the time displayed at the lower right corner ofthe navigation screen, as well as other time options,you must first reach the Adjust Clock screen. To get tothe Adjust Clock screen, do the following:

1. Press the CONFIG key to access the Setup menu.

2. Select the Clock option.

To change the hours/minutes on the clock, do thefollowing:

1. Using the joystick, highlight the time, and press thejoystick to select it.

2. Move the joystick up or down to adjust the hour.

3. Once the desired hour is reached, move the joystickto the right to highlight the minutes.

4. Move the joystick up or down to adjust the minutes.

5. When the desired minutes have been reached,press OK to save the change, or select Enter toadjust other time options before you press OKto save.

12Hr/24Hr: This feature allows you to choose whetherthe time is displayed in standard or military time.Using the joystick, choose 12Hr for standard time, or24Hr for military time.

Auto GPS Update: With this feature ON, the navigationsystem time will be set to match the current GPStime. The time will be updated with the GPS time whenthe ignition is turned to ACCESSORY or RUN. Usingthe joystick, you may also choose OFF to turn thisfeature off.

1-7

Daylight Savings: With this feature ON, the navigationsystem will automatically adjust the time for DaylightSavings. Using the joystick, you may also choose OFFto turn this feature off.

Time Zone: This feature allows you to choosefrom four different time zones: P.S.T. (Pacific),M.S.T. (Mountain), C.S.T. (Central) andE.S.T. (Eastern). Use the joystick to choose thedesired zone.

Remember that you must press OK after making thedesired adjustments to any of the time options.This allows your changes to be saved and will returnyou to the Setup menu. If you hit the back key withoutpressing OK, you will return to the Setup menu, butnone of your changes will be saved.

English/Metric UnitsThis option allows you to select either English or metricmeasurements to appear for distances on the map.

If your vehicle is equipped with a Driver InformationCenter (DIC), the navigation system will use the metricmeasurement selected through the vehicle’s DIC.

To change between English and metric measurements,do the following:


2. Using the joystick, select Nav Setup.

3. Use the joystick to choose the measurement optionyou desire. Choose miles to display measurementsin English, or km (kilometers) to display metricmeasurements.

4. Press the back key to return to the previous screen.

5. To return to the main navigation screen, or to seethe map, press the NAV or map keys.

See “Nav (Navigation) Setup” under Navigation Menuon page 2-7 for more information.

1-8

Features and Controls ......................................2-2Using the Navigation System ...........................2-2Navigation System Screen ...............................2-4Maps ............................................................2-5Symbols ........................................................2-6Navigation Menu ............................................2-7

Global Positioning System (GPS) ....................2-30Vehicle Positioning ........................................2-31Problems with Route Guidance .......................2-32If the System Needs Service ..........................2-32Ordering Map DVDs ......................................2-32Database Coverage Explanations ....................2-32

Section 2 Features and Controls

2-1

Features and Controls

Using the Navigation SystemThis section presents basic information you will need toknow to operate the navigation system.

The main navigation menu displays a number of optionswhich offer information on a variety of topics. SeeNavigation Menu on page 2-7 for more information.

Use the keys located on each side of the navigationscreen, and the joystick located on the bottom left cornerof the navigation system, to operate the system. Seethe navigation system overview under Introductionon page 1-2 for more information on location.

Use the navigation joystick to move left, right, up, downor diagonally on the screen. Press the center of thejoystick to enter a selection.

Once the vehicle is moving, various functions will bedisabled to reduce driver distractions.

Hard KeysThe following hard keys are located to the left of thenavigation screen:

• Z (Eject)

• NAV RPT

• SEEK

• NAV

• BAND

• B (CD)

• e (Audio)

• CONFIG (Configure)

The function of each of these keys will be explained inthis manual.

The system also has the following reconfigureable softkeys located to the right of the navigation screen.They have hard key labels for easier understandingwhile in navigation mode. These six keys can alsochange functions for different modes of the system.

) (Map): Press the map key to view the map screenshowing current vehicle position.

2-2

DEST (Destination): Press the DEST key to displaythe Destination menu. See “Destination” underNavigation Menu on page 2-7 for more information.

y (Menu): Press the menu key to display the mainnavigation menu. See Navigation Menu on page 2-7 formore information.

V (Zoom In): Press the zoom in key to get a closerlook at a smaller section of the map you are traveling on.

U (Zoom Out): Press the zoom out key to see alarger scale of the map you are traveling on. You canalso view your highlighted route.

W (Back): Press the back key to return to theprevious screen.

Alpha-Numeric KeypadLetters of the alphabet, symbols, punctuation, andnumbers, when available to you, will be displayed onthe navigation screen as an alpha or numeric keypad.The appropriate keypad will automatically be displayedwhenever the system needs information from you.

The alpha keypad will automatically be displayed whenthe system needs you to input a street or city name.The numeric keypad will automatically be displayedwhen the system needs you to input a phone number orhouse address.

To select a character, use the joystick to move acrossthe keypad, and press the center of the joystick toselect it.

U (Space): Select the space symbol to enter aspace between characters or the words of a name.

V (Backspace): Select the backspace symbol if youhave selected an incorrect character.

To make your name selections easier, the system willonly allow you to select a character which can follow thelast one entered. For example, if you enter Z, youwould not be allowed to follow it with T. The system willhighlight the available characters and darken theunavailable characters.

If you are unsuccessful when inputting a name, it mayneed to be selected differently. It is also possible that themap DVD database may not contain that information.See Database Coverage Explanations on page 2-32 formore information.

2-3

Navigation System ScreenThe navigation screen is located in the center of theinstrument panel. See Introduction on page 1-2 for moreinformation.

P (Power/Volume Knob): Press the power/volumeknob to turn on the audio and navigation systems. Turnthe knob clockwise or counterclockwise to increaseor decrease the volume to the audio system. Press theknob again to turn off the audio and navigationsystems.

NAV RPT (Navigation Repeat): Press the NAV RPTkey to repeat the current audio navigation prompt.

NAV (Navigation): If you are in a menu and are not onthe map screen, press the NAV key located to the leftof the navigation screen to view the current mapshowing vehicle position.

If a route has not been planned, pressing the NAV keywill display the map screen and the followinginformation:

• North or Heading up symbol in upper left corner

• Time

• Map scale

If a route has been planned, pressing the NAV key willdisplay the map screen and the following information:

• Number of miles/kilometers between currentvehicle position and the destination

• Estimated travel time to the destination

• Highlighted route or turn-by-turn instructions

You will find more information on each feature found ona map screen, later in this manual.

2-4

MapsThis section includes basic information that you need toknow about the map database.

The maps are stored on a DVD-ROM. The48 contiguous Unites States and portions of Canadaare contained on one disc. The U.S. map databaseincludes interstate freeways, state highways, countryroads and major and general streets.

Refer to the “Navigation System Map Disc” manual toview the explanation of map coverage. The mapdisc manual will be in your map DVD case when thevehicle is delivered from the factory.

When your vehicle is delivered from the factory, thedealer may have installed the map DVD. If the DVD wasnot installed in your vehicle when first purchased, dothe following:

1. Turn the ignition switch to RUN or ACCESSORY.

2. If already loaded, eject the map DVD or audioCD from the slot.

3. Load the map DVD into the slot by inserting itpartway. The system will pull it in.

Once the DVD is inserted correctly, you will have thefollowing two choices:

• ENG (English)

• FR (French)

You can select the language at this time. See“Language” under Screen Setup on page 1-4 forinformation on choosing a language. Once a languagehas been selected, select NEXT to plan a route.The map will appear showing your current vehicleposition.

Map AdjustmentsThe system allows you to adjust the scale of view onthe map. Also, the map will scroll automatically basedon the direction you are traveling.

To view a larger or smaller scale of the map, press thezoom out or zoom in keys. See “Hard Keys” underUsing the Navigation System on page 2-2 for moreinformation.

Map ScalesThe scale of a map can range from 1/32 of a mile(0.05 km) to 124 miles (200 km).

2-5

SymbolsThe following symbols are the most common thatappear on a map screen.

Your vehicle is shown asthis symbol. It indicates thecurrent position of yourvehicle on the map.

This red bulls-eye symbolwill appear on the map toshow your destinationafter a route has beenplanned.

See “Destination” under Navigation Menu on page 2-7for information on planning a route.

When one of five possible destinations has been set,you will see a circle with numbers 1 through 5,depending on which number destination it is.

This symbol indicates themap with North up.

While in North up mode, North will always be at the topof the map screen, regardless of which direction thevehicle is traveling. See “Map Appearance” underNavigation Menu on page 2-7 for more information.

This symbol indicates themap with the vehicle traveldirection up.

The shaded triangle indicates North. While in Headingup mode, the direction your vehicle is traveling willalways be at the top of the map screen. See “MapAppearance” under Navigation Menu on page 2-7 formore information.

2-6

Navigation Menu

The main navigation menu allows you to choose from alist of options, and to use the available keys to makesystem adjustments and plan routes. Press themenu key to access the main navigation menu.

You will be able to choose from the following list ofitems on the main navigation menu:

• Suspend Guidance

• Route Overview

• Map Appearance

• Voice Volume

• DVD (DVD Information)

• Edit Route

• Route Preview

• Nav (Navigation) Setup

• Memory Points

A detailed description of each item follows in thissection.

Suspend GuidanceWhen this function is selected, guidance to all currentand programmed destinations is suspended, butthe current route will be retained in memory. You will nolonger receive voice prompts for navigation. The mapcan still be viewed by pressing the map key. If yoususpend guidance, the Resume Guidance key will allowyou to resume the current route.

Route OverviewSelecting Route overview will show the map with theroute highlighted. The total distance and estimated traveltime are also displayed.

2-7

Map Appearance

The Map Appearance menu allows you to adjust theappearance of a map based on your preferences.This menu is divided into three sections: Maporient (orientation), Guidance mode, and Map mode.Use the joystick to scroll through and select the optionsyou want. The following are brief explanations of theoptions available in each section:

North up: This feature orients the map with North atthe top of the map screen, regardless of which directionyou are driving.

Heading up: This feature orients the map with thedirection you are driving at the top of the map screen,regardless of which direction is North.

3D view: This feature gives maps a 3-dimensionalview, and will remain in the Heading up position.

Arrow: This feature continually displays directional turnguidance for your next maneuver.

Turn list: This feature lists information on your nextthree maneuvers, including the distance to the turn, andstreet names.

Map: This feature will display your current position, withthe calculated route highlighted.

Single: This feature allows one map to be displayed.

Split screen: This feature allows two maps to bedisplayed, which can be independently adjusted in bothscale, and map orientation. When in Split screenmode, the right screen can be chosen to display Arrowor Turn list guidance modes.

For more information on the symbols that can appearon a map screen, see Symbols on page 2-6.

2-8

Voice Volume

This system has voice guidance prompts that providevarious messages as you approach points whereyou need to maneuver your vehicle, such as anintersection.

To adjust the volume of the voice prompts you receivefrom the system, do the following:


2. Select Voice Volume.

3. Use the joystick to raise or lower the volume. Thevoice prompt will come on with each adjustment togive you an idea of the volume at each level.

4. Once you have reached the desired volume level,press the back key to return to the previous screen.

With Adaptive voice volume control, the volume of voiceprompts will increase automatically once the vehicleexceeds 50 mph (80 km/hr). Select On to activate thisfeature.

If you do not need voice guidance, you may also selectOff to turn the prompts off.

DVD InformationSelecting DVD will display the information for thecurrent navigation database disc.

2-9

Edit Route

This function allows you to recalculate a route based onyour preferences. You can also add, reorder, ordelete destinations, and adjust road preference settings.

The Search Condition screen allows you to select yourroute preference by choosing from Fastest, Shortest,or Alternative route. By selecting the Fastest route, youwill be routed along main roads and highways, whichdoes not necessarily mean it will be the shortest route.

2-10

The Route Preference screen allows you to select yourroad preferences by setting which types of roadsyou wish to use and avoid.

Route Preview

Selecting Route preview from the main navigation menudisplays the map screen with the route highlighted.The route is traced by the vehicle symbol as you travel.You can preview the route from the starting positionto the destination.

2-11

Nav (Navigation) Setup

Selecting Nav setup displays the Nav Setup menu.From this menu, several options may be selected,adjusted, or turned on and off. The following areavailable options from the Nav Setup menu, with a briefexplanation of each:

English/Metric: This features switches distancemeasurements between standard or metricmeasurements. Choose miles for standardmeasurements, or km (kilometers) for metricmeasurements.

Notify seasonal restrict (restrictions): This featurecan route you around seasonal restrictions, suchas a closed road. Choose On to have your routesautomatically calculated around seasonal restrictions, orOff to turn this feature off.

Estimated travel time: This feature displays theestimated time to travel from your current position to thedestination. Choose On to have the estimated traveltime displayed with the distance to destination, or Off toturn this feature off.

Enter speed change?: This feature allows you toadjust estimated speeds for Freeway, Main street orResidential driving. These speed values are usedto calculate estimated travel time. To change estimatedspeeds, choose Yes. The Change Speed menu willappear. Move the joystick up or down to highlight theroad type you want to change. Then move the joystick tothe right to increase, or to the left to decrease thespeed. The maximum allowable speed to set is100 mph (161 km). When your adjustments arecomplete, press the back key to return to the NavSetup menu.

Auto reroute: With this feature On, the navigationsystem will automatically recalculate a route if you driveoff course. Choose Off to turn this feature off.

2-12

Voice guide in all mode: With this feature On, you willhear navigation voice prompts while in Audio and CDmodes. Choose Off to turn off the voice prompts in thosemodes.

Current street name: With this feature On, the currentstreet name will be displayed. Choose Off to turn thisfeature off.

Map color (Day): This feature allows you to adjust thedaytime map appearance using the joystick. Choosebetween Normal, Auto, 1, 2, 3 or 4. The numberedsettings vary the color scheme of the map display.The Auto setting will change the map appearanceautomatically every three months. When the desiredcolor setting has been selected, press the map key toview the adjusted map color.

Map color (Night): This feature allows you to adjustthe nighttime map appearance using the joystick.Choose between Normal, Auto, 1, 2, 3 or 4. Thenumbered settings vary the color scheme of the mapdisplay. The Auto setting will change the mapappearance automatically every three months. Whenthe desired color setting has been selected, pressthe map key to view the adjusted map color.

Operation guide on map: This feature allows you toremove the toolbar from the bottom of the display screenin order to see more of the map. Choose Off toremove the toolbar from the display screen. Choose Onto restore the toolbar to the display screen.

Calibrate system?: This feature will calibrate wheelspeed to assist in the calculation of vehicle position.This feature also allows you to manually reposition thevehicle symbol on the map. You may need to calibratethe system following a tire change, rotation, or ifyour vehicle has been relocated a great distance.Choose Yes to calibrate the system, or No to leave thecalibration as it is.

Select defaults?: This feature allows you to restore allavailable factory default settings in the Nav Setupmenu. Choose Yes to restore defaults, or No to retainthe current settings.

Exit information: This feature will display map iconswhich can be selected to display the next exit’sinformation, including Point of Interest (POI) facilitiessuch as gas stations, restaurants, and lodging. ChooseOn to display exit information icons, or Off to cancelthe display of exit information icons.

2-13

Memory Points

Selecting this function will display the Memory Pointsmenu. This menu contains options for registering,deleting, and editing marked points stored in memory,such as Memory Points, preset destinations andareas to avoid.

Choosing to register a Memory Point will take you to theDestination entry screen. The name, location,information, and icon for a Memory Point may be edited.

Five preset destinations, as well as one for Home,may be registered or edited. The five preset destinationsand Home are the only destination selections availablefrom the Destination entry screen while the vehicleis moving. See “Destination” following in this section formore information on how to register Memory Pointsand preset destinations.

Up to 10 areas to avoid may also be registered from theMemory Points menu. Areas to avoid include areassuch as a high traffic area, construction area, orany main road or intersection you wish to avoid. Whenregistering or editing an area to avoid, the size ofthe area may be increased or decreased by using thejoystick.

2-14

Destination

The Destination screen will give you more ways to plana route by entering destination points. Press theDEST key to display the Destination screen.

The Destination screen allows you to select the area tobe searched for your destination. A map of the UnitedStates and a part of Canada divided into 8 regionswill be shown. Before selecting a method of destinationentry, review the search area map on the right sideof the Destination screen to make sure your destinationis located in the highlighted region.

If you need to see a more detailed search area mapwith a list of states, or to change the search area, selectChange. Use the joystick to highlight the number forthe desired region, then press the center of the joystickto select it. The Destination screen will returnautomatically.

2-15

To enter a destination, choose from one of the followingdestination entry methods:

Address

The Address destination entry method allows you toinput an address by providing the system with a housenumber, street name, and city. Select Street nameto begin entering the desired address.

Enter the street name using the alpha keypad. See“Alpha-Numeric Keypad” under Using the NavigationSystem on page 2-2 for more information. Do not includename extensions such as N., or Drive. For example,the street name N. Civic Center Drive should be enteredas Civic Center. As information is entered, the systemwill automatically search for available names, andthe List key will become available. Press the List key toview available name choices and select the desiredstreet name, or continue to spell the street nameto further reduce the number of available items.

Once the street name has been selected, enter thehouse number using the numeric keypad. The systemwill list the house number range that is available for thestreet. When you have finished entering the housenumber, select OK.

If the house number and street address you enteredexists in more than one city on the DVD database, a listof cities will appear. You can select a city name fromthe list, or enter the city name by selecting City,then Input City Name. As you begin to enter the cityname, you can select the desired city from the list whichwill appear, or continue to spell the city name tofurther reduce the number of available items.

Once your destination entry is complete, a screen withthe destination preview menu will be displayed. See“Destination Preview Menu” later in this section for moreinformation.

2-16

Point of Interest (POI)

The Point of Interest (POI) destination entry methodallows you to choose a destination from the POIlist. Selecting POI from the Destination screen bringsup the Point of Interest entry menu. The POIs inthe database are cross referenced between Name,Category and City Names.

You may search for a POI by using a combination ofthe following three methods:

• Type in a POI by name using the alpha-numerickeypad. As you type in a name, the system willsearch for an available match to your input. Selectthe correct POI name.

• Select a POI by choosing the Category option.Select a category from the list the system willsupply. If the list of available POIs for the categoryselected is still too long, you may need to inputthe name or city for the POI.

• Select the City button and then type in the city youwish to select a POI from.

While inputting a POI or city name, the List key willbecome available. Press the List key to view the list ofavailable name choices, or continue to spell thename to further reduce the list of available items.


2-17

The following list shows the types of facilities in theDVD database that you can choose from when usingPOI options. GM brand names can be selected tolocate automobile related facilities specific to thatbrand name.

• Airport

• Amusement Park

• ATM

• Auto Service & Maintenance

• Automobile Club

• Automobile Dealership

• Bank

• Border Crossing

• Bowling Center

• Buick®

• Bus Station

• Business Facility

• Cadillac®

• Casino

• Chevrolet®

• City Center

• Community Center

• Commuter Rail Station

• Court House

• Exhibition Center

• Ferry Terminal

• Gas Station

• Golf Course

• Government Office

• GMC®

• Grocery Store

• Historical Monument

• Hospital

• Hotel

• Ice Skating Center

• Library

• Rest Area

• Marina

• Movie Theater

2-18

• Museums

• Night Club

• Oldsmobile®

• Other

• Park & Ride

• Park/Recreation Area

• Parking Garage

• Parking Lot

• Performing Arts

• Police Station

• Pontiac®

• Post Office

• Public Sports Airport

• Rental Car Agency

• Railway Station

• Restaurant

• Saab®

• Saturn®

• School

• Shopping

• Ski Resort

• Sports Complex

• Theatre

• Tourist Attraction

• Tourist Information

• Town Hall

• University

• Winery

If an arrow appears to the right or left of the item name,the complete name is too long for the display. Usethe joystick to choose the right or left arrow, then pressthe joystick to select it. The item name will scroll tothe end or beginning of its name.

The POI for Restaurant is broken down into severaldistinct categories. Select Restaurant from the POIchoices. A list of cuisine types will then appear.

2-19

Memory Points

The Memory points destination entry method allows youto select a destination by choosing from a list ofmarked points on the map that were previously marked.Memory points include up to 30 saved points andfive preset destinations. Selecting marked points fromthe Destination screen allows you to select any oneof the marked points as the active destination. Markedpoints can also be sorted by icon, date saved, oralphabetically.

If you choose to register a memory point, you will beable to select an icon to correspond with that memorypoint. You will be given a screen with several iconsto choose from. You can also choose to registerthat memory point by using a sound, which you select.To select a sound, choose With Sound, and pressthe joystick to select it.


Preset DestinationThe Preset destination entry method allows you toselect destinations that were registered as presets1 through 5. Besides the Home preset destination, theseare the only presets available for selection while thevehicle is moving.


2-20

Previous Destination

The Previous destination entry method allows you toselect a destination by choosing from a list of previousdestinations, once they are entered.


Intersection

The Intersection destination entry method allows you toselect a destination by inputting the intersectingroads you wish to travel to. To enter a destination usingthis method, select Intersection from the Destinationscreen. Then enter the name of the street, but donot include name extensions such as N., or Drive. Forexample, the street name N. Civic Center Driveshould be entered as Civic Center. This will bring up alist of streets with that name. Select the desiredstreet name from the list.

2-21

Now begin entering the second street name, andchoose the desired street name from the list. After bothstreet names in the intersection have been selected,a list of cities containing the selected intersectionwill appear. If there are several cities that contain thatspecific intersection, you must specify a city. Selectthe desired city from the list. The route will thenbe calculated, and you will hear a voice prompt directingyou to “Proceed to the highlighted route.” If you donot hear a voice prompt, your voice guidance promptsmay have been turned off. See “Voice Volume” earlier inthis section for more information.


Phone Number

The Phone Number destination entry method allows youto search for a point of interest (POI) destination byentering the POI phone number. Use the joystickto enter the POI phone number on the numeric keypadand select OK. The destination location will then bedisplayed. Most phone numbers for POIs included in theDVD database can be entered to locate a destination.Cellular phone numbers and internal company phonenumbers cannot be entered to locate a destination.


2-22

Emergency

The Emergency destination entry method allows you toselect a destination by choosing from a list ofemergency facilities. The list will vary by area. SelectingPolice Station or Hospital will display a list. The listcan be changed to appear in alphabetical order, or inorder by distance.


Freeway Entrance/Exit

The Freeway Entrance/Exit destination entry methodallows you to select a destination by entering a freewayentrance or exit point. Use the joystick to enterFreeway names on the alpha keypad.


2-23

Prev (Previous) Start PointThe Previous start point destination entry method allowsyou to select the last start point as a destination.


HomeThe Home destination entry method allows you tochoose home as a destination. Use the joystick to selectHome from the Destination screen. Besides presetdestinations 1 through 5, this is the only preset availablefor selection while the vehicle is moving.


MapThe Map destination entry method displays the lastlocation on the map, and the road preference.

Use the joystick to select Map from the Destinationscreen, then scroll across the map to locate yourdestination. Once you have located the desireddestination, press the joystick to select it. The route willthen be calculated, and you will hear a voice promptdirecting you to “Proceed to the highlighted route.” If youdo not hear a voice prompt, your voice guidanceprompts may have been turned off. See “Voice Volume”earlier in this section for more information.

You may also zoom out to view the entire regional map.See “Hard Keys” under Using the Navigation Systemon page 2-2 for more information. However, if you zoomout as much as possible and scroll around the map,some parts of the map will appear to be missingbecause they are not readable in larger scales.

Once your destination entry is complete, a screen withthe destination preview menu will be displayed. See“Destination Preview Menu” following in this section formore information.

2-24

Destination Preview Menu

Each time a destination is entered, a screen with thedestination preview menu will appear. This screenwill display a zoomed in view of the destination, as wellas the following options:

Map scroll: This option allows you to scroll the mapand make small adjustments to the desired destination,for greater accuracy.

Add: This option will add the displayed destination tothe current route. If there is more than one destinationentered into the system, the Add Destination screen willbe displayed.

Replace: This option will replace a destination to thecurrent route of the displayed destination.

Info: This option will display the telephone number forthe point of interest (POI) which contains the displayedinformation in the database.

Route preference: This option will display the RoutePreference screen. To adjust your route preferences,select Change, located below the road type icons. Seethe route preference screen under “Edit Route”earlier in this section for more information.

Once the desired adjustments from the destinationpreview menu are complete, the route overview menucan be displayed. See “Route Overview Menu” followingin this section for more information.

2-25

Route Overview MenuEach time a destination has been selected and thedesired adjustments from the destination preview menuare complete, the route overview menu can bedisplayed. Press the joystick to display the followingthree options:

Start: This option will choose the default road type,calculate the route, and begin route guidance forthe displayed route.

3 Routes: This option will display the map withthree highlighted routes shown in three different colorsfor Fastest, Shortest, and Alternative route.

After selecting one of the three routes, the road distanceand estimated travel time will be displayed. TheFastest route means you will be routed along mainroads and highways, and does not necessarily mean itis the shortest route.

Edit Route: This option allows you to change yourroute preferences. See “Edit Route” earlier in thissection for more information.

Press the back key at any time to return to the previousscreen.

2-26

Map Menu

Once you select a destination and begin your route, youcan press the center of the joystick to view a menuwith additional route options. Use the joystick to selectfrom the following route options:

POI icon Off: This option allows you to turn off Point ofInterest (POI) icons shown on the map.

POI selection: This option allows you to choose whichtypes of POIs will be displayed on the map.

Once you choose POI selection, the Show POI Iconsscreen will appear and display the different POIcategories. Use the joystick to select up to five differentPOI categories. The icons for the selected categorieswill then be displayed on the map.

2-27

To view a list of local POIs, select Local POI List. TheLocal POI List screen will list the closest POIs fromthe categories you have selected. You can sort thesePOIs by distance, icon/category, or name. You can alsoselect Route to display POIs along your current route.Once you select the desired POI, a map of the area witha symbol marking the destination will be displayed.

Guide: This option allows you to view POI informationby selecting the desired POI icon on the map.

To use this feature, you must have at least one POIcategory selected to appear on the map and thenselect Guide.

Moving the joystick left or right will move from one iconto the next, displaying the POI name and distancefrom the vehicle’s current location. While the POI icon issurrounded by a red box, you can press the joystickagain to select it, and the POI name, address, andphone number will also be displayed.

POI information will only be displayed while the vehicleis not moving.

Cancel route: This option allows you to cancel thecurrent, or first destination. The second programmeddestination will then be used if one is available and/orentered.

Suspend guidance: This option allows you to suspendactive route guidance for all current and programmeddestinations. See “Suspend Guidance” earlier inthis section for more information.

2-28

Chg. route: This option allows you to change the routesearch condition while the vehicle is moving. Thefollowing options may be available:

• Detour for 1 mile?: Select Yes to recalculate yourroute and detour for one mile around the vehicle’scurrent position.

• Detour for 3 mile?: Select Yes to recalculate yourroute and detour for three miles around thevehicle’s current position.

• Change to fastest?: Select Yes to recalculate yourroute to the fastest route.

• Change to shortest?: Select Yes to recalculate yourroute to the shortest route.

• Reroute from adjacent road?: Select Yes torecalculate your route from another road on yourroute, near the vehicle’s current position.

Map orient/3D view: This option allows you to choosethe way you view the map as you travel.

Mark: This option allows you to save a point to memory.

Right Screen: If you currently have a split-screen,this option allows you to adjust options for the screen tothe right.

Colors on the MapWhen a route has been planned, it will be highlightedon the screen in blue.

Different colors are also used to distinguish betweeninterstate freeways, state highways, county roads, majorstreets and secondary streets. Highways will beshown as a thicker line than a general street.

2-29

Global Positioning System (GPS)The Navigation System determines the position of yourvehicle by using satellite signals, various vehiclesignals and map data.

The Global Positioning System (GPS) locates thecurrent position of your vehicle using signals sent by theUnited States Department of Defense GPS Satellites.While your vehicle is receiving signals from thesatellites, GPS will not appear on the map screen.

However, at times, other interferences such asthe satellite condition, road configuration, the conditionof the vehicle and/or other circumstances can interferewith the system’s ability to determine the accurateposition of the vehicle. This is when GPS will appear onthe map screen.

The system may not be available or interferences mayoccur if any of the following are true:

• Signals are obstructed by tall buildings, large trucksor a tunnel.

• Metallic objects are located on the dashboard.

• Satellites are being repaired or improved.

• Aftermarket glass tinting has been applied to thevehicle’s windshield.

Do not apply aftermarket glass tinting to the vehicle’swindshield or place metallic objects on the vehicle’sdashboard. Glass tinting and metallic objects willinterfere with the system’s ability to receive GPS signalsand may cause the system to malfunction.

If you are experiencing a problem, see “VehiclePositioning” and “Problems with Route Guidance”following for more information.

2-30

Vehicle PositioningAt times, the position of the vehicle on the map may beinaccurate due to one or more of the followingreasons:

• The road system has changed.

• The vehicle is traveling on slippery road surfacessuch as sand, gravel and/or snow.

• The vehicle is being driven on winding roads.

• The vehicle is being driven on a long straight road.

• The vehicle is approaching a tall building or alarge vehicle.

• The surface streets run parallel to a freeway.

• The vehicle has just been transferred by a vehiclecarrier or a ferry.

• The current position calibration is set incorrectly.

• The vehicle is being driven at high speeds.

• The vehicle is repeating a change of directions bygoing forward and backward, or turning on a turntable in a parking lot.

• The vehicle is entering and/or exiting a parking lotor garage with a roof.

• The vehicle has a roof carrier, ski or bike rackinstalled on it.

• The vehicle has tire chains on it.

• The tires have been replaced.

• The tire pressure is incorrect.

• The tires are worn.

• The battery is disconnected.

• The vehicle is driven in heavy traffic where drivingis at low speeds and the vehicle is stopped andstarted repeatedly.

2-31

Problems with Route GuidanceInappropriate route guidance may occur under any ofthe following conditions:

• You have not turned onto the road indicated by thesystem.

• Route guidance is not available for the next right orleft turn.

• The route is not changed during automatic rerouting.

• Plural names of places are displayed.

• You are driving at high speeds, which may causethe automatic rerouting to operate slower.

• The route prohibits the entry of a vehicle due to aregulation by time or season or any other regulationwhich may be given.

• A route cannot be found.

• A road is new, was recently changed or is not listedon the DVD. The route to the destination may notbe shown. See “Ordering Map DVDs” later inthis section.

If the System Needs ServiceIf you are still experiencing difficulty with your NavigationSystem after reading this information, see your dealerfor assistance.

Ordering Map DVDsThe map DVD in your vehicle is the most up-to-dateinformation available when your vehicle was purchased.The map DVD is updated once a year, provided thatthe map information has changed. To order a new DVD,contact your dealer.

Database Coverage ExplanationsCoverage areas vary with respect to the level of mapdetail available for any given area. Some areas willfeature greater levels of detail than others. If thishappens, it does not mean there is a problem with thesystem. As the map DVD is updated, more detailmay become available for areas which previously hadlimited detail. See “Ordering Map DVDs” earlier inthis section.

2-32

Navigation Audio System ..................................3-2

Section 3 Navigation Audio System

3-1

Navigation Audio SystemThe audio system has been designed to operate easilyand give years of listening pleasure. You will get themost enjoyment out of it if you acquaint yourself with itfirst. Find out what your audio system can do andhow to operate all its features, to be sure you’re gettingthe most out of the advanced engineering that wentinto it.

The ignition must be in ACCESSORY or RUN for youraudio system to work.

The audio system is operated using the menus locatedon the navigation system screen. The audio menusare explained in this section.

Playing the RadioThe audio system can be operated using the knobs andhard keys located on both sides of the navigationscreen. See the navigation system overview underIntroduction on page 1-2 for more information onlocation.

O (Power/Volume): Press this knob to turn the audioand navigation systems on and off. While the audiosystem is on, you can turn the knob clockwise orcounterclockwise to increase or decrease the volume.

Finding a Station

BAND: Press this key to access the BAND screen andto switch between AM, FM1, FM2, or XM1 and XM2,if equipped. Each radio band has six station presetsaccessible.

TUNE: Use the joystick in the lower left corner of thenavigation system to choose a radio station.

w SEEKx: Press the up or the down arrow to go tothe next or to the previous station and stay there.

To scan stations, press and hold the SEEK up or downarrow for two seconds until you hear a beep. Theradio will go to a station, play for a few seconds, thengo on to the next station. Press either SEEK arrow againto stop scanning.

To scan preset stations, press and hold the SEEK up ordown arrow for more than four seconds. You will heartwo beeps and PSCAN will be displayed, along with thehighlighted preset. The radio will go to one of thepreset stations, play for a few seconds, then go on tothe next preset station. Press either SEEK arrowagain to stop scanning presets.

The radio will seek and scan only to stations that are inthe selected band and only to those with a strongsignal.

3-2

Setting Preset StationsThe six multi-function keys located to the right of thenavigation screen, allow you to store your favoritestations. You can store up to 30 stations (6 AM, 6 FM1,6 FM2, 6 XM1 and 6 XM2, if equipped). To set presetstations, do the following:

1. Turn the audio system on.

2. Press the BAND key to select the desired band(AM, FM1, FM2, XM1 or XM2, if equipped).

3. Locate the desired station using the SEEK key orthe joystick.

4. Press and hold one of the six keys located to theright of the navigation screen, until you hear abeep. Whenever you press that key while in theBAND menu, the station you set will return.

5. Repeat the steps for each preset and source.

Audio Screen

If the radio is on while the navigation system is in use, asmaller audio screen will appear, located on the leftside of the map screen. This audio screen will displaythe current audio information, such as band and station.

FM1 Source Shown, Other Sources Similar

3-3

e (Audio): Press the Audio hard key to display theaudio menu. Several options are available foradjustment from this menu.

Tone: Choose from six available settings to adjust thetone of the audio system. Use the joystick to movebetween Treble, Midrange, Bass, Balance and Fade.Use the joystick to move each setting to the desiredlevel.

FM2 Source Shown, Other Sources Similar

3-4

AVC (Automatic Volume Control): If your system hasAVC, your audio system monitors the noise in thevehicle. Then, AVC automatically adjusts the volumelevel so that it always sounds the same to you. To useAVC, use the joystick to select on, to turn it off,select off.

From the Audio Menu, you may be able to use the rightside hard keys to choose from four different equalizationsettings if your system has these:

Normal: This setting enhances the stereo effect.

Driver: This setting gives the driver the best soundquality.

Rear: This setting gives the rear seat passengers thebest sound quality.

Spacious: This setting makes the listening spaceseem larger. Speed Compensated Volume (SCV): If your system

has SCV, your audio system adjusts automaticallyto make up for road and wind noise as you drive. Setthe volume at the desired level. Then, as you drive, SCVautomatically increases the volume, as necessary, toovercome noise at any speed. The volume level shouldalways sound the same to you as you drive.

3-5

EQ (Equalizer): While in the Audio menu on somesystems, you can use the keys labeled EQ1 throughEQ5 to choose preset bass, midrange, and trebleequalization settings if your vehicle is equipped withthese. The CUSTOM key allows you to choose andset the equalization levels you desire. Use the joystickto move between Treble, Midrange and Bass, andto adjust each setting to the desired level. To set thelevels, press and hold the CUSTOM key until you heara beep.

After adjustments are made, press the BAND key to goback to the preset station menu. Now that you havepreset the station and the EQ setting, you can assign theEQ to the preset station. To do this, press and holdthe desired preset station key until you hear a beep. TheEQ setting will now be assigned to that station unlessyou decide to change it.

If you were at the CD screen before setting an EQ andyou press the CD hard key, you will be returned tothe CD screen, and the EQ will be set to that screenuntil you change it.

See “Rear Seat Audio (RSA)”, “Theft-Deterrent Feature”,“Audio Steering Wheel Controls”, and “UnderstandingRadio Reception”, in your vehicle’s owner’s manualfor more information.

Radio Data Systems (RDS)Your audio system is equipped with a Radio DataSystem (RDS). Using RDS, the radio can do thefollowing:

• Seek only to stations broadcasting the selectedtype of programming.

• Seek to stations with traffic announcements.

• Receive announcements concerning local andnational emergencies.

• Display messages from radio stations.

RDS features are only available on FM stations thatbroadcast RDS information. The RDS features on yourradio rely on receiving specific RDS information fromthese stations. These features will only work when theRDS information is available. In rare cases, a radiostation may broadcast incorrect information thatwill cause the radio features to work improperly. If thishappens, contact the radio station.

While you are tuned to an RDS station, the stationname will appear on the display. RDS stations mayprovide a program type (PTY) for current programmingand the name of the program being broadcast.

3-6

RDS Option Menu

Once you are at the FM screen, press the center of thejoystick to bring up the RDS Option Menu. Here youwill be able to choose from the following RDS options:

RDS Seek: This function allows the system to stoponly on stations which broadcast one of the programtypes (PTY) selected in the PTY Selection menu.You may select All to allow the radio to stop on anyradio station broadcasting RDS data.

Press the SEEK up or down arrow to look for otherstations with that PTY. If a station with the selected PTYis not found, the radio will return to the original station.

PTY (Program Type): The program types (PTY) youcan select from include: Adult Hits, Classical, ClassicalRock, College, Country, Information, Jazz, Language,News, Nostalgia, Oldies, Personality, Public, Rhythm andBlues, Religious Music, Religious Talk, Rock Music, Soft,Soft Rock, Soft R & B, Sports, Talk, Top 40 and Weather.

To select PTY preferences, do the following:

1. From the RDS Option menu, press the PTY key toview the available PTYs.

2. Use the joystick to select as many PTYs as desired.You may also select None to cancel selected PTYs,or Any to select all PTYs.

3-7

RDS Messages: This feature allows radio stationmessages to be displayed on the audio screen whenthey are received.

Alternate Frequency: This feature allows the radio toautomatically switch to a stronger station in an RDSnetwork that is playing the same network broadcast.While the frequency may change, the station call lettersshould stay the same, as they are in the same RDSnetwork.

Regionalization: This feature allows the tuner toremain on the current RDS station, even if it departsfrom RDS network broadcast in favor of broadcastinglocal or regional content.

Traffic: This option allows you to hear trafficannouncements. With this feature ON, if a trafficannouncement is available, it will interrupt what you arecurrently listening to. When the traffic announcementis over, the previous audio selection will resume.

When the Traffic feature is ON, TA will appear next tothe clock on the bottom right corner of the screen.The radio will continue to search for stations with thecapability to broadcast traffic information. When a trafficannouncement has been found, TP will appear belowTA. If you are in the main audio screen when atraffic announcement begins, TRAFFIC will be displayed.

Interrupt Volume: This feature allows you to set thevolume level at which the audio system will play a trafficannouncement. Use the joystick to choose this option,and to move the volume to the desired level.

XM™ Satellite Radio Service(48 Contiguous US States)Your vehicle may be equipped with this feature. XM™ isa continental U.S. based satellite radio service thatoffers 100 coast to coast channels including music,news, sports, talk and children’s programming. XM™provides digital quality audio and text information,including song title and artist name. A service fee isrequired in order to receive the XM™ service. For moreinformation, contact XM™ at www.xmradio.com orcall 1-800-852-XMXM (9696).

3-8

XM™ Options

Move the joystick up or down to scroll through a list ofcategories. Press SEEK while the change to windowis up to seek to the first station in the selected category.Push the joystick left or right to scan through stationsin the selected category.

When XM™ is active, the channel name and number,song title and artist will be displayed on the screen.

To access the XM™ Options, you must be in the Radioscreen with the XM1 or XM2 band active. SelectOptions to access the XM™ Menu.

This menu allows you to seek or scan for stationsbased on their category. While in this menu you canuse the joystick to scroll through the categories you wantto seek to. Use the SCAN option at the bottom of thescreen to go to the first available channel in thatcategory.

If the category scan/seek lock is on, performing ascan/seek will scan/seek only in the selected category.

3-9

XM™ Radio MessagesRadio Display

Message Condition Action Required

XL (Explicit LanguageChannels)

XL on the radio display,after the channel name,indicates content withexplicit language.

These channels, or any others, can be blocked at acustomer’s request, by calling 1-800-852-XMXM (9696).

XM Updating Updating encryption code The encryption code in your receiver is being updated, andno action is required. This process should take no longerthan 30 seconds.

No XM signal Loss of signal Your system is functioning correctly, but you are in alocation that is blocking the XM signal. When you moveinto an open area, the signal should return.

Loading XM Acquiring channel audio(after 4 second delay)

Your radio system is acquiring and processing audio andtext data. No action is needed. This message shoulddisappear shortly.

Channel Off Air Channel not in service This channel is not currently in service. Tune in to anotherchannel.

Channel Unavail Channel no longeravailable

This previously assigned channel is no longer assigned.Tune to another station. If this station was one of yourpresets, you may need to choose another station for thatpreset button.

No Artist Info Artist Name/Feature notavailable

No artist information is available at this time on thischannel. Your system is working properly.

No Title Info Song/Program Title notavailable

No song title information is available at this time on thischannel. Your system is working properly.

3-10

XM™ Radio Messages (cont’d)Radio Display

Message Condition Action Required

No CAT Info Category Name notavailable

No category information is available at this time on thischannel. Your system is working properly.

Not Found No channel available forthe chosen category

There are no channels available for the category youselected. Your system is working properly.

No Information No Text/Informationalmessage available

No text or informational messages are available at thistime on this channel. Your system is working properly.

XM Theftlocked Theft lock active The XM receiver in your vehicle may have previously beenin another vehicle. For security purposes, XM receiverscannot be swapped between vehicles. If you receive thismessage after having your vehicle serviced, check with theservicing facility.

XM Radio ID Radio ID label (channel 0) If you tune to channel 0, you will see this messagealternating with your XM Radio 8 digit radio ID label. Thislabel is needed to activate your service.

Unknown Radio ID not known(should only be ifhardware failure)

If you receive this message when you tune to channel 0,you may have a receiver fault. Consult with your dealer.

Check XM Receiver Hardware failure If this message does not clear within a short period of time,your receiver may have a fault. Consult with your retaillocation.

See “Understanding Radio Reception” and “XM™ Satellite Radio Antenna System (48 Contiguous US States)” inyour vehicle’s owner’s manual for more information.

3-11

Playing a Compact DiscRemove the navigation map DVD from the slot andreturn it to its case. Insert a CD partway into the slot,label side up. The player will pull it in.

There will be a 12 to 15 second delay while the CD isread, before it begins to play. When the player begins toread a CD, the Disc Check in Process message willappear briefly to remind you of the delay. When the mapDVD is reinserted and read, the DVD Check inProcess message will appear briefly to remind you ofthe delay.

While playing a CD in the CD player, the navigationsystem is not available. A message will display ifthe NAV key is pressed. If your vehicle is equipped withRear Seat Entertainment (RSE), you can play anaudio CD while using the navigation system. See “RearSeat Entertainment System” later in this section formore information.

CD (Compact Disc): Press this key to change toplaying a CD when listening to the radio. The CD screenwill then be displayed.

Y (Eject): Press this key to eject a CD.

Repeat: Press this key to repeat the track that iscurrently being played. Press Repeat again to turn thisfeature off.

3-12

Random: Press this key to play the tracks in random,rather than sequential, order. Press Random againto turn off random play.

[ (Forward): Press and hold this key to quicklyadvance within a track. As the CD advances, elapsedtime will be displayed to help you find the correctpassage. Release this key to play the passage.

r (Reverse): Press and hold this key to quicklyreverse within a track. As the CD reverses, elapsed timewill be displayed to help you find the correct passage.Release this key to play the passage.

w SEEKx: Within two seconds, press and releasethe SEEK up arrow to advance to the next track, orthe down arrow to return to the previous track.

Track Scan: Press and hold one of the SEEK arrowsfor two seconds or more to enter CD TRACK SCANmode. A chime will sound to alert you that TRACKSCAN is active, and the first 10 seconds of each trackon the disc will be played before advancing to thenext track. Press one of the SEEK arrows again to stopthe scan at the track currently being played.

BAND: Press the BAND key to switch to the radiowhen a CD is playing.

Compact Disc Messages

CD ERROR: If this message appears on the screen,the CD is not being read by the system. The CD couldbe dirty, scratched, wet, or upside down. You mayalso be driving on a very rough road. When the roadbecomes smoother, the CD should play.

NO MUSIC DISC: If this message appears on thescreen, the map DVD is still inserted in the system.Press eject and return the map DVD to its case, theninsert a CD. The CD should play.

NO DISC: If this message appears on the screen, theCD slot is empty. Insert a CD. The CD should play.

If a CD is not playing correctly for any other reason, trya known good CD. If any error occurs repeatedly orif an error cannot be corrected, contact your dealer. Ifyour radio displays an error message, write it down andprovide it to your dealer when reporting the problem.

See “Rear Seat Audio (RSA)”, “Care of Your CDsand DVDs”, and “Care of Your CD and DVD Player” inyour vehicle’s owner’s manual for more information.

3-13

✍ NOTES

3-14

AAdjust Clock .................................................... 1-7Alpha-Numeric Keypad ...................................... 2-3Audio Screen ................................................... 3-3Audio System .................................................. 3-2

BBeep .............................................................. 1-5

CColors on the Map .......................................... 2-29Contrast/Brightness ........................................... 1-5

DDatabase Coverage Explanations ...................... 2-32Destination ..................................................... 2-15Display Off ...................................................... 1-6DVD Information ............................................... 2-9

EEdit Route ..................................................... 2-10English/Metric Units .......................................... 1-8

FFinding a Station .............................................. 3-2

GGlobal Positioning System (GPS) ...................... 2-30

HHard Keys ....................................................... 2-2

IIf the System Needs Service ............................ 2-32Introduction ...................................................... 1-2

LLanguage ........................................................ 1-5

MMap Adjustments .............................................. 2-5Map Appearance .............................................. 2-8Map Scales ..................................................... 2-5Maps .............................................................. 2-5

1

Memory Points ............................................... 2-14Menu, Navigation .............................................. 2-7

NNav (Navigation) Setup .................................... 2-12Navigation

Menu .......................................................... 2-7System Screen ............................................. 2-4Using the System .......................................... 2-2

OOrdering

Map DVDs ................................................. 2-32

PPlaying a Compact Disc ................................... 3-12Playing the Radio ............................................. 3-2Problems with Route Guidance ......................... 2-32

RRadio ............................................................. 3-2Radio Data Systems (RDS) ................................ 3-6

Route Overview ................................................ 2-7Route Preview ................................................ 2-11

SScreen Color ................................................... 1-5Screen Setup ................................................... 1-4Setting Preset Stations ...................................... 3-3Suspend Guidance ........................................... 2-7Symbols .......................................................... 2-6System Screen, Navigation ................................ 2-4

UUsing the System, Navigation ............................. 2-2

VVehicle Positioning .......................................... 2-31Voice Volume ............................................ 2-9, 1-6

XXM™ Options .................................................. 3-9XM™ Satellite Radio Service

(48 Contiguous US States) ............................. 3-8

2

2004 HUMMER H2 Navigation System Mgmhummer.com/hummerspecs/2004H2_nav_system.pdf · Navigation...

Documents

Transcript of 2004 HUMMER H2 Navigation System Mgmhummer.com/hummerspecs/2004H2_nav_system.pdf · Navigation...