HUMMER SERIES

PRODUCT NAME: HUMMER H3VERSION: 72W LEDDIMENSION(MM): 1610 × 138 × 115BODY MATERIAL: ALUMINIUMDIFFUSER MATERIAL: PC

PRODUCT NAME: HUMMER H1VERSION: 24W LEDDIMENSION(MM): 700 × 138 × 115BODY MATERIAL: ALUMINIUMDIFFUSER MATERIAL: PC

PRODUCT NAME: HUMMER H2VERSION: 48W LEDDIMENSION(MM): 1310 × 138 × 115BODY MATERIAL: ALUMINIUMDIFFUSER MATERIAL: PC

SHANGHAI P&Q LIGHTING CO., LTD

SPECIFICATION

ALUMINIUM INDUSTRIAL LIGHT

ta40

CATALOGUE

PARTS LISTS & EXPLODED ASSEMBLY DRAWINGS PAGE 3

QUICK SPECIFICATION & DIM DRAWINGS PAGE 5

SPECIFICATION & LIGHT DISTRIBUTION PAGE 6

INSTALLATION INSTRUCTION PAGE 7

PACKING INFORMATION PAGE 9

CONTACT INFORMATION PAGE 10

PARTS LISTS & EXPLODED ASSEMBLY DRAWINGS

1

5

5

7

7

EXPLODED ASSEMBLY DRAWINGS

HUMMER H1

HUMMER H2

PARTS LISTS

8

8

6

1

2

3

4

6

1

2

3

4

1. 1610MM PC DIFFUSER ×1

2. ALUMINIUM GEAR TRAY ×2

3. SILICONE SPONGE GASKET ×1

4. ALUMINIUM DIE CASTING BODY ×1

5. PLUG 20 MM CONDUIT GREY WITH RUBBER WASHER ×2

6. SCREW M6 X 16 S/S SOCKET HD ×10

7. WASHER FLAT 6X9.5X0.55 S/STEEL ×6

8. WASHER HARD SILICON 5.8X10.8X2.5 ×6

PARTS LISTS & EXPLODED ASSEMBLY DRAWINGS

EXPLODED ASSEMBLY DRAWINGS PARTS LISTS

1. 1610MM PC DIFFUSER ×1

2. 1520MM ALUMINIUM GEAR TRAY ×2

3. SILICONE SPONGE GASKET ×1

4. 1610MM ALUMINIUM DIE CASTING BODY ×1

5. PLUG 20 MM CONDUIT GREY WITH RUBBER WASHER ×2

6. SCREW M6 X 16 S/S SOCKET HD ×14

7. WASHER FLAT 6X9.5X0.55 S/STEEL ×8

8. WASHER HARD SILICON 5.8X10.8X2.5 ×8

HUMMER H3

NOTE :

1. ACCEPT BOTH WHOLE LIGHT ORDERS AND HOUSING KIT ORDERS.2. WHOLE LIGHT INCLUDES ALL THE PARTS IN THE PARTS LIST ALSO WITH PCB, CHIPS, DRIVER BE ASSEMBLED COMPLETELY.3. HOUSING KIT ONLY INCLUDES THE PARTS ON THE PARTS LIST.4. 2 PCS GEAR TRAY INSIDE, ONE FOR PCB AND LED CHIPS, THE OTHER FOR DRIVER.5. EITHER WHOLE LIGHT ORDER OR HOUSING KIT ORDER INCLUDE BRACKET. 6. ACCEPT BRACKET ORDER.

ACCESSORIES DRAWINGS

HUMMERACC1 HUMMERACC2 HUMMERACC3 HUMMERACC4 HUMMERACC5 HUMMERACC6

5

7

8

6

1

2

3

4

FREELANDERACC1 M20 CABLE GLAND

SPECIFICATION & LIGHT DISTRIBUTION

FEATURES

● THREE FORMATS 24W 700MM LONG, 48W 1310MM LONG, 72W 1610MM LONG.● LER = 102LM/W CCT = 4000K CRI>80. ● ENERGY EFFICIENT LED BOARDS INTEGRATED ELECTRONICS AND DIFFUSE LENS● 50,000 HOURS AVERAGE LAMP LIFE L70● PRESSURE DIE-CAST MARINE GRADE ALUMINIUM BODY WITH A POWDER COATED PAINT FINISH● COMPLETE WITH SECURITY SCREWS, REMOVABLE GEAR TRAY AND SINGLE ONE PIECE GASKET● LOW PROFILE IP66 PROTECTION, IK10● ROBUST FROSTED POLYCARBONATE LENS RESIST IMPACT & ABUSE● OPTIONAL BODY PROFILES AND MOUNTING ACCESSORIES● DUAL CONDUIT ACCESS ● AMBIENT TEMPERATURE, -25°C TO 40°C● EMERGENCY VERSIONS AVAILABLE

APPLICATIONS

PRISONS, SUBWAYS, RAILWAY STATIONS ANDUNDERGROUND CARPARKS.

CERTIFICATE CERTIFICATE NO.----------------------------------------------------------------------------------------------------------CE BCTC-150911291 BCTC-150911292 IP66 BCTC-150911293 ETL 150801588SHA-001EXN IIC ZONE 2, T5 IP66 N. 0B150930. HECTS73

PRODUCTS QUICK INFORMATION

VERSION DIM (MM) MASS (KG)----------------------------------------------------------------------------------------------------------24W LED 700×140×115 2.0 36W LED 1310×140×115 3.5 72W LED 1610×140×115 4.0

ACCESSORIES ----------------------------------------------------------------------------------------------------------M20 CABLE GLAND

CEILING MOUNT BRACKETBRACKET 45°SINPLE PIPE MOUNT BRACKET KITSUNIVERSAL BRACKET

PICTURE

700.0

1310.0

1610.0

140.0

115.0

DIM (MM)

SPECIFICATION & LIGHT DISTRIBUTION

SPECIFICATION LIST

HUMMER H1 HUMMER H2 HUMMER H3

POWER 24W 48W 72W

NOMINAL VOLTAGE AC90-240V AC90-240V AC90-240V

POWER FACTOR ＞0.95 ＞0.95 ＞0.95

PCB CONNECTION 12 SERIES 12 PARALLELS 12 SERIES 24 PARALLELS 12 SERIES 24 PARALLELS

DRIVER OUTPUT 32-40V/0.5A 32-40V/0.5A 32-40V/0.5A

PCB QUANTITY 2PCS 4PCS 4PCS

CHIPS EPISTAR 5630 EPISTAR 5630 EPISTAR 5630

CHIP QUANTITY 144PCS 288PCS 288PCS

CCT 3000-6000K 3000-6000K 3000-6000K

CRI ＞80 ＞80 ＞80

LUMINOUS FLUX 2585LM 5081LM 8271.484LM

EFFICIENCY 103LM/W 102LM/W 102.234LM/W

BEAM ANGLE 120° 120° 120°

BODY MATERIAL ALUMINIUM ADC12 ALUMINIUM ADC12 ALUMINIUM ADC12

DIFFUSER MATERIAL PC PC PC

IP RATE IP66 IP66 IP66

AMBIENT TEMPERTURE -25°C TO 40°C -25°C TO 40°C -25°C TO 40°C

STORAGE TEMPERATURE -25°C TO 70°C -25°C TO 70°C -25°C TO 40°C

INNER BOX DIM(MM) 710×140×125 1320×140×125 1650×140×125

OUTER BOX DIM(MM) 725×300×390 1335×300×390 1665×300×270

0 1530

345330

315 45

300 60

285 75

90270255 105

1,500

1,250

1,000

750

500

250

0 1530

345330

315 45

300 60

285 75

90270255 105

1,500

1,250

1,000

750

500

250

HUMMER H1 HUMMER H2 HUMMER H3

0 1530

345330

315 45

300 60

285 75

90270255 105

1,500

1,250

1,000

750

500

250

——C0-180 ——C90-270

INSTALLATION INSTRUCTION

INSTALLATION OR ASSEMBLY INSTRUCTIONS

PLEASE READ THESE INSTALLATION INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR MAINTAINING THISEQUIPMENT. THESE INSTRUCTIONS AND LOCAL REGULATIONS(WHERE APPLICABLE), BY AN AUTHORISED AND LICENCED ELECTRICIAN.

IMPORTANT – THE PRODUCT MUST BE MAINTAINED AND OPERATED IN ACCORDANCE WITH THE MANUFACTURE’S INSTRUCTIONS, FAILURE TO DO SO MAY DAMAGE THE PRODUCT AND SERVICES. IT IS STRONGLY RECOMMENDED THAT THIS IMPORTANT NOTE BE COMMUNICATED TO THE OWNER AND OR OPERATOR OF THE INSTALLATION AT THE TIME OF SITE COMMISSIONING. GOOD PRACTICE DOES NOT RECOMMEND THE 24/7 USE OF PRODUCTS WITHOUT THE APPLICATION OF SUITABLE SWITCH CYCLE INTERVALS. PNQ IS NOT RESPONSIBLE FOR ANY PRODUCT NOT MAINTAINED IN ACCORDANCE WITH THE RECOMMENDED PROCEDURES. ALL PRODUCTS SHOULD BE THOROUGHLY CLEANED ON A REGULAR BASIS TO ENSURE THE OPTICAL PERFORMANCE, TOGETHER WITH THE ELECTRICAL,MECHANICAL AND STRUCTURAL INTEGRITY AS DESIGNED, IS MAINTAINED THROUGHOUT THE SERVICE LIFE OF THE PRODUCT.

“CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR”

1. PRODUCT SPECIFICATION:

HUMMER H1 HUMMER H2 HUMMER H3———————————————————————————————————————————————————————————————TYPE OF PROTECTION CLASS EXN IIC ZONE 2, T5 EXN IIC ZONE 2, T5 EXN IIC ZONE 2, T5———————————————————————————————————————————————————————————————IP RATING IP66 IP66 IP66———————————————————————————————————————————————————————————————NOMINAL VOLTAGE AC180-240V AC180-240V AC180-240V———————————————————————————————————————————————————————————————LINE CURRENT 0.6A 1.2A 1.8A

IMPORTANT – WHEN INSTALLING ELECTRONIC OR HID LIGHTING EQUIPMENT, THE INSTALLER MUST CONSIDER THE IN-RUSH START CURRENT(IF ANY)ASDOCUMENTED ON THE CONTROL GEAR IDENTIFICATION LABEL WHEN SELECTING APPROPRIATE CIRCUIT CONTROLS OR PROTECTIVE DEVICES.

POWER FACTOR ＞0.95 ＞0.95 ＞0.95———————————————————————————————————————————————————————————————NOMINAL FREQ.(HZ) 50 50 50 ———————————————————————————————————————————————————————————————SUITABLE FOR DIRECT MOUNTING ON YES YES YESFLAMMABLE SURFACES——————————————————————————————————————————————————————————————— DIMMABLE(IF RELEVANT REFERBRAND WEB FOR APPROVED LIST) NO NO NO———————————————————————————————————————————————————————————————

2. STORAGE: PRIOR TO INSTALLATION PRODUCTS ARE TO BE STORED IN COOL AND DRY CONDITIONS.

3. APPLICATION: THE INSTALLATION APPLICATION AND ORIENTATION OF THE PRODUCT IS DESIGNED IN ACCORDANCE WITH THE NOMINATED PRODUCT IP RATING, CLASS DESIGNATION AND THESE INSTALLATIONS. INSTALLATION ENVIRONMENTS OUTSIDE THESE CONDITIONS ARE NOT RECOMMENDED.

4. INSTALLATION / GENERAL: INSTALLATION OF THE PRODUCT IS TO BE COMPLETED BY AN AUTHORIZED AND LICENSED ELECTRICIAN, IN ACCORDANCE WITH THESE INSTRUCTIONS, RELEVANT STANDARDS AND LOCAL REGULATIONS (WHERE APPLICABLE). TERMINATION OF PRODUCT WIRING, TOGETHER WITH THE INSTALLATION OF THE PRODUCT MUST BE IN A MANNER THAT MAINTAINS THE INTEGRIT OF THE DESIGNATED IP RATING OF THE PRODUCT FOR ELECTRONIC CONTROL EQUIPMENT (WHEN SUPPLIED) DO NOT MEGGER BETWEEN A AND N.

5. INSTALLATION AND SAFETY: THIS PRODUCT WHEN OPERATED UNDER NORMAL USE SHALL PROVIDE YEARS OF SERVICE WITH MINIMAL OR NO MAINTENANCE NEEDED. HOWEVER, CARE IS EXPECTED IN INSTALLING THIS PRODUCT. ALL REQUIREMENTS OF “HEALTH AND SAFETY” SHALL BE MET. THE LUMINAIRES ARE CLASS 1 AND SHOULD BE EFFECTIVELY EARTHED. CERTIFICATION DETAILS ON THE RATING PLATE MUST BE VERIFIED AGAINST THE APPLICATION REQUIREMENTS BEFORE INSTALLATION. THE INFORMATION IN THIS LEAFLET IS CORRECT AT THE TIME OF PUBLICATION. THE COMPANY RESERVES THE RIGHT TO MAKE SPECIFICATION CHANGES AS REQUIRED.

6. TOOL REQUIREMENTS: INSTALLATION TOOLS INCLUDE 3MM AND 5MM FLAT BLADE SCREWDRIVER, PLIERS, 5MM HEX KEY, KNIFE AND WIRE STRIPPERS OR CUTTERS. FOR HIGH SECURITY FITTINGS ONLY, SPECIAL TOOLS MAY BE REQUIRED FOR COMPLETE INSTALLATION.

7. ELECTRICAL SUPPLIES: ALWAYS ENSURE THE CORRECT SUPPLY VOLTAGE IS AS THE RATING LABEL ON THE PRODUCT. SLIGHT VARIATIONS OF THE NOMINAL LINE VOLTAGE WITHIN THE RANGE OF +6%/-6% ARE EXPECTED, ALTHOUGH LUMINAIRES SHOULD NOT BE OPERATED CONTINUOUSLY AT MORE THAN +6%/-10% OF THE RATED SUPPLY VOLTAGE OF THE CONTROL GEAR OR TAPPING.

INSTALLATION OR ASSEMBLY INSTRUCTIONS

PLEASE READ THESE INSTALLATION INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR MAINTAINING THISEQUIPMENT. THESE INSTRUCTIONS AND LOCAL REGULATIONS(WHERE APPLICABLE), BY AN AUTHORISED AND LICENCED ELECTRICIAN.

IMPORTANT – THE PRODUCT MUST BE MAINTAINED AND OPERATED IN ACCORDANCE WITH THE MANUFACTURE’S INSTRUCTIONS, FAILURE TO DO SO MAY DAMAGE THE PRODUCT AND SERVICES. IT IS STRONGLY RECOMMENDED THAT THIS IMPORTANT NOTE BE COMMUNICATED TO THE OWNER AND OR OPERATOR OF THE INSTALLATION AT THE TIME OF SITE COMMISSIONING. GOOD PRACTICE DOES NOT RECOMMEND THE 24/7 USE OF PRODUCTS WITHOUT THE APPLICATION OF SUITABLE SWITCH CYCLE INTERVALS. PNQ IS NOT RESPONSIBLE FOR ANY PRODUCT NOT MAINTAINED IN ACCORDANCE WITH THE RECOMMENDED PROCEDURES. ALL PRODUCTS SHOULD BE THOROUGHLY CLEANED ON A REGULAR BASIS TO ENSURE THE OPTICAL PERFORMANCE, TOGETHER WITH THE ELECTRICAL,MECHANICAL AND STRUCTURAL INTEGRITY AS DESIGNED, IS MAINTAINED THROUGHOUT THE SERVICE LIFE OF THE PRODUCT.

“CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR”

1. PRODUCT SPECIFICATION:

HUMMER H1 HUMMER H2 HUMMER H3———————————————————————————————————————————————————————————————TYPE OF PROTECTION CLASS EXN IIC ZONE 2, T5 EXN IIC ZONE 2, T5 EXN IIC ZONE 2, T5———————————————————————————————————————————————————————————————IP RATING IP66 IP66 IP66———————————————————————————————————————————————————————————————NOMINAL VOLTAGE AC180-240V AC180-240V AC180-240V———————————————————————————————————————————————————————————————LINE CURRENT 0.6A 1.2A 1.8A

IMPORTANT – WHEN INSTALLING ELECTRONIC OR HID LIGHTING EQUIPMENT, THE INSTALLER MUST CONSIDER THE IN-RUSH START CURRENT(IF ANY)ASDOCUMENTED ON THE CONTROL GEAR IDENTIFICATION LABEL WHEN SELECTING APPROPRIATE CIRCUIT CONTROLS OR PROTECTIVE DEVICES.

POWER FACTOR ＞0.95 ＞0.95 ＞0.95———————————————————————————————————————————————————————————————NOMINAL FREQ.(HZ) 50 50 50 ———————————————————————————————————————————————————————————————SUITABLE FOR DIRECT MOUNTING ON YES YES YESFLAMMABLE SURFACES——————————————————————————————————————————————————————————————— DIMMABLE(IF RELEVANT REFERBRAND WEB FOR APPROVED LIST) NO NO NO———————————————————————————————————————————————————————————————

2. STORAGE: PRIOR TO INSTALLATION PRODUCTS ARE TO BE STORED IN COOL AND DRY CONDITIONS.

3. APPLICATION: THE INSTALLATION APPLICATION AND ORIENTATION OF THE PRODUCT IS DESIGNED IN ACCORDANCE WITH THE NOMINATED PRODUCT IP RATING, CLASS DESIGNATION AND THESE INSTALLATIONS. INSTALLATION ENVIRONMENTS OUTSIDE THESE CONDITIONS ARE NOT RECOMMENDED.

4. INSTALLATION / GENERAL: INSTALLATION OF THE PRODUCT IS TO BE COMPLETED BY AN AUTHORIZED AND LICENSED ELECTRICIAN, IN ACCORDANCE WITH THESE INSTRUCTIONS, RELEVANT STANDARDS AND LOCAL REGULATIONS (WHERE APPLICABLE). TERMINATION OF PRODUCT WIRING, TOGETHER WITH THE INSTALLATION OF THE PRODUCT MUST BE IN A MANNER THAT MAINTAINS THE INTEGRIT OF THE DESIGNATED IP RATING OF THE PRODUCT FOR ELECTRONIC CONTROL EQUIPMENT (WHEN SUPPLIED) DO NOT MEGGER BETWEEN A AND N.

5. INSTALLATION AND SAFETY: THIS PRODUCT WHEN OPERATED UNDER NORMAL USE SHALL PROVIDE YEARS OF SERVICE WITH MINIMAL OR NO MAINTENANCE NEEDED. HOWEVER, CARE IS EXPECTED IN INSTALLING THIS PRODUCT. ALL REQUIREMENTS OF “HEALTH AND SAFETY” SHALL BE MET. THE LUMINAIRES ARE CLASS 1 AND SHOULD BE EFFECTIVELY EARTHED. CERTIFICATION DETAILS ON THE RATING PLATE MUST BE VERIFIED AGAINST THE APPLICATION REQUIREMENTS BEFORE INSTALLATION. THE INFORMATION IN THIS LEAFLET IS CORRECT AT THE TIME OF PUBLICATION. THE COMPANY RESERVES THE RIGHT TO MAKE SPECIFICATION CHANGES AS REQUIRED.

6. TOOL REQUIREMENTS: INSTALLATION TOOLS INCLUDE 3MM AND 5MM FLAT BLADE SCREWDRIVER, PLIERS, 5MM HEX KEY, KNIFE AND WIRE STRIPPERS OR CUTTERS. FOR HIGH SECURITY FITTINGS ONLY, SPECIAL TOOLS MAY BE REQUIRED FOR COMPLETE INSTALLATION.

7. ELECTRICAL SUPPLIES: ALWAYS ENSURE THE CORRECT SUPPLY VOLTAGE IS AS THE RATING LABEL ON THE PRODUCT. SLIGHT VARIATIONS OF THE NOMINAL LINE VOLTAGE WITHIN THE RANGE OF +6%/-6% ARE EXPECTED, ALTHOUGH LUMINAIRES SHOULD NOT BE OPERATED CONTINUOUSLY AT MORE THAN +6%/-10% OF THE RATED SUPPLY VOLTAGE OF THE CONTROL GEAR OR TAPPING.

8. MOUNTING: LUMINAIRES SHOULD BE INSTALLED WHERE ACCESS FOR MAINTENANCE IS PRACTICAL AND IN ACCORDANCE WITH ANY LIGHTING DESIGN INFORMATION PROVIDED FOR THE INSTALLATION. THE FOLLOWING MOUNTINGS ARE POSSIBLE.

CEILING MOUNT BRACKET SINPLE PIPE MOUNT BRACKETS BRACKET 45° UNIVERSAL BRACKET WALL BRACKET HUMMERACC1×2PCS HUMMERACC3×2PCS HUMMERACC2×2PCS HUMMERACC5×2PCS FREELANDERACC1×4PCS SCREW M6×8×4PCS HUMMERACC3×4PCS SCREW M6×8×4PCS SCREW M6×8×4PCS HUMMERACC6×2PCS SCREW M6×8×10PCS SCREW M6×8×10PCS NUT M6×8×6PCS

9. CABLING AND FITTING LAMPS: ACCESS FOR CABLING AND FITTING LAMPS IS DONE BY FIRSTLY REMOVING THE FRONT COVER, AFTER WHICH THE GEAR TRAY IS REMOVED. INSTALL THE CONDUCTORS INTO THE APPROPRIATE TERMINALS. DO NOT STRIP THE INSULATOR EXCESSIVELY, 1MM BARE CONDUCTOR OUTSIDE THE TERMINAL IS A MAXIMUM. ANY UNUSED TERMINAL SHOULD BE FULLY TIGHTENED. V90 HT CABLE SHOULD BE USED. AFTER CABLING IS COMPLETE MAKE A FINAL TIGHTNESS AND CONNECTION CHECK. LAMPS MUST BE OF THE CORRECT TYPE AS SPECIFIED BY THE LAMP REPLACEMENT LABEL AND MUST BE PROPERLY INSERTED AND LOCKED. THE GEAR TRAY IS THEN LOCKED AFTER WHICH THE DIFFUSER IS APPLIED AND TIGHTENED WITH THE APPROPRIATE TOOL.“DO NOT OVERTIGHTEN DIFFUSER FIXING SCREWS OR DAMAGE MAY OCCUR – RECOMMENDED TORQUE SETTING OF 4 NM”

10. ROUTING EXAMINATION: THE EQUIPMENT MUST BE DE-ENERGISED BEFORE OPENING TO AVOID SHOCK.1) ENSURE THE LAMP IS LIT WHEN ENERGISED AND THAT THE LAMP GLASS IS NOT DAMAGED.2) WHEN DE-ENERGISED AND LEFT TO COOL THERE SHOULD BE NO SIGN OF INTERNAL MOISTURE. IF THERE ARE SIGNS OF WATER INGRESS, THE LUMINAIRE SHOULDBE OPENED UP, DRIED OUT, AND ANY LIKELY INGRESS POINTS ELIMINATED BY INSTALLING A NEW GASKET.3) CHECK THE CABLE GLAND FOR TIGHTNESS AND TIGHTEN IF NECESSARY.4) CHECK THE TIGHTNESS OF THE DIFFUSER SCREWS AND TIGHTEN IF NECESSARY.5) CLEAN THE LAMP GLASS.6) UPON CHANGING LAMPS CHECK THAT THE DIFFUSER GASKET HAS NOT SOFTENED OR BECOME EXCESSIVELY DEFORMED, IF IN DOUBT REPLACE.

11. ELECTRICAL FAULT FINDING AND RELACEMENT: THE SUPPLY MUST BE ISOLATED BEFORE OPENING THE LUMINAIRE. IN MOST INSTANCES ANY ELECTRICAL FAULTS ARE SIMPLE, NAMELY LOOSE OR BROKEN CONNECTIONS, UNSERVICEABLE LAMPS OR OPEN CIRCUIT CONTROL GEAR. CONTROL GEAR WILL NOT GO OPEN CIRCUIT IN MOST INSTANCES UNLESS IT HAS BEEN OVERHEATED. OVERHEATED CONTROL GEAR CAN BE EASILY FOUND FROM SEVERE DISCOLOURATION OF THE PAINT ON THE GEAR AND CRACKS IN ANY EXPOSED INSULATION. IT IS UNUSUAL FOR A CONTROL GEAR TO OVERHEAT, SO PLEASE ENSURE THAT ALL CONNECTIONS ARE MADE CORRECTLY. IF ALL CONNECTIONS ARE VERIFIED TO BE CORRECT, THE PRODUCTS ENVIRONMENT MAY BE HAVING AN ADVERSE EFFECT TO THE COMPONENTS. IF THIS IS THE CASE PLEASE CONTACT YOUR SUPPLIER FOR A MORE SUITABLE REPLACEMENT. ANY FAULT FINDING MUST BE DONE BY A FULLY QUALIFIED ELECTRICIAN AND, IF CARRIED OUT WITH THE LUMINAIRE IN PLACE, UNDER A PERMIT TO WORK. WITH REPLACEMENT OF ANY PARTENSURE THAT WIRES AND CONNECTIONS ARE CHECKED, AND ANY WIRE SLEEVING REFITTED.

12. INSTALLATION / SPECIAL CONDITIONS (RELEVANT ONLY FOR PRODUCTS APPROVED FOR SUCH AN INSTALLATION) :(A) PRODUCTS INSTALLED IN HIGH WIND ENVIRONMENTS MUST HAVE SUITABLE INSTALLATION / FASTENING METHODS APPLIED TO ENSURE PRODUCT’S MOUNTING POINTS ARE NOT DAMAGED THROUGH, CORROSION, CONSTANT VIBRATION AND OR MOVEMENT. EXTERIOR PRODUCTS ARE DESIGNED WITH PRECISE VERTICAL AIMING LIMITS, WHICH SHOULD NOT BE EXCEEDED.(B) PRODUCTS INSTALLED IN CORROSIVE OR SALT LADEN ENVIRONMENTS REQUIRE SPECIAL CONSIDERATION AND SUCH; SPECIFIC PRODUCT SELECTION, INCLUSIVE OF SUITABLE FASTENING METHODS AND EXTENSIVE ONGOING MAINTENANCE OF PRODUCTS INSTALLED IN THESE ENVIRONMENTS REQUIRE PROFESSIONAL ADVICE. IT IS ESSENTIAL THAT ALL ASPECTS OF THE PRODUCT SELECTION, MATERIAL SPECIFICATION AND MAINTENANCE ARE SPECIFICALLY DESIGNED FOR SUCH USE.(C) INTERIOR HIGHBAY PRODUCTS MUST BE VERTICALLY SUSPENDED. THE METHOD OF SUSPENSION (CHAIN ETC) MUST BE ABLE TO SUPPORT AT LEAST 5 TIMES THE TOTAL WEIGHT OF THE FITTING. DO NOT INSTALL WHERE AIR MOVEMENT WILL CAUSE THE FITTING TO SWING ABOUT, CAUSING WEAR AND TEAR OF ATTACHMENT POINTS. LUMINAIRES SHOULD BE INSTALLED WHERE ACCESS FOR MAINTENANCE IS PRACTICAL AND ALLOWS FOR MAINTENANCE TO BE COMPLETEDIN ACCORDANCE WITH THE MANUFACTURER’S RECOMMENDATIONS.(D) INTERIOR (DOWNLIGHT) PRODUCTS MUST BE INSTALLED TO ENSURE THE LAMP UNIT OR THE DRIVER ARE NOT COVERED WITH ANY COMBUSTIBLE MATERIALS OR INSULATION; MINIMUM SPACINGS NOMINATED FOR THESE MATERIALS ARE MANDATORY. THE MINIMUM CLEARANCE OF 25MM AROUND AND 100MM ABOVE THE DOWNLIGHT FROM INSULATION OR COMBUSTIBLE MATERIAL IS REQUIRED UNLESS OTHERWISE NOMINATED. FOR DIMMING PURPOSES PLEASE SEE THE RELEVANT PRODUCT BRAND WEB SITE FOR THE DIMMING COMPATIBILITY CHART. WHEN MOUNTING MULTIPLE FIXTURES TO CONDUCTIVESTRUCTURES, IT IS RECOMMENDED THAT THE STRUCTURE IS EARTHED. THE MOUNTING FACILITIES PROVIDED FOR THE TRANSFORMER/DRIVER (IF ANY) ,NEED ONLY BE UTILIZED IF IN THE APPLICATION OF THE PRODUCT IS REQUIRED. IP RATINGS STATED (IF ANY) ARE FROM BELOW THE CEILING UNLESS STATED OTHERWISE AND THE INSTALLATION OF THE PRODUCT MUST BE IN A MANNER THAT MAINTAINS THE INTEGRITY OF THE RELEVANT IP RATING.

1 2 3 4 5

INSTALLATION INSTRUCTION

14. MAINTENANCE:(A) THE SUPPLY MUST BE ISOLATED BEFORE OPENING OR ACCESSING THE LUMINAIRE. PRODUCT MAINTENANCE IS IMPORTANT AND IS CRITICAL TO THE PRODUCTS DESIGNED PERFORMANCE. THE PRODUCT IS TO BE MAINTAINED IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS. FOR THE LATEST PRODUCT MAINTENANCE GUIDES PLEASE GO TO RELEVANT BRAND WEB SITE. PNQ IS NOT RESPONSIBLE FOR ANY PRODUCT NOT MAINTAINED IN ACCORDANCE WITH THE RECOMMENDED PROCEDURE OR INTERVALS.(B) LAMPS (WHERE PROVIDED): THE PRODUCT IS DESIGNED WITH THE SUPPLIED (LEDS) / LAMPS / AND IT IS STRONGLY RECOMMENDED THAT ANY LAMP / (LEDS) CHANGES ( IF ANY ) BE MADE IN ACCORDANCE WITH THE TYPE, COLOUR AND BRAND SUPPLIED. FOR RECOMMENDED LAMP / LED MAINTENANCE OR OPERATING GUIDES (INCLUSIVE OF RECOMMENDED PRODUCT SWITCH CYCLES AND MANDATORY RUN-IN PROCEDURES FOR HID AND FLUORESCENT LAMPS WHEN USED WITH DIMMING CIRCUITS), PNQ RECOMMENDS THE APPLICATION OF THE LAMP MANUFACTURER’S OPERATING GUIDELINES, WHICH CAN BE FOUND ON MANUFACTURER’S WEBSITE. PNQ IS NOT RESPONSIBLE FOR THE PRODUCT PERFORMANCE OF ALTERNATIVE LAMP/S USED. AS A MEMBER OF FLUROCYCLE, WE ENCOURAGE RECYCLING OF LAMPS AND COMPONENTS.(C) BATTERY (WHERE PROVIDED): THE BATTERY IS DESIGNED WITH A RATED AVERAGE BATTERY DESIGN LIFE OF 25,000 HRS IN STANDBY MODE. THE BATTERY IS SUPPORTED WITH A STANDARD 12 MONTH WARRANTY; CONDITIONAL OF THE PRODUCT BEING MAINTAINED AND OPERATED IN ACCORDANCE WITH THE MANUFACTURER’S GUIDELINES. FOR GUIDELINES SEE PRODUCT INSTALLATION INSTRUCTIONS OR VISIT THE RELEVANT BRAND WEB SITE.(D) FOR PRODUCTS SUPPLIED WITH GLASS VISORS OR COVERS, DO NOT OPERATE THE PRODUCT WITH A DAMAGED VISOR OR COVER; IT SI RECOMMENDED THE PRODUCT BE TURNED OFF, AREA SURROUNDING THE PRODUCT VACATED AND THE DAMAGED GLASS REPLACED BY A PROFESSIONAL INSTALLER IMMEDIATELY.

15. WARRANTY: PRODUCT WARRANTY IS IN ACCORDANCE WITH PNQ STANDARD TERMS AND CONDITIONS OF SALES, UNLESS SPECIFICALLY STATED OTHERWISE IN THIS DOCUMENT. FOR THE LATEST TERMS AND CONDITIONS OF SALE PLEASE SEE THE RELEVANT PRODUCT BRAND WEB SITE.__________________________________________________________________________________________________________________

PACKING INFORMATION

INSTALLATION INSTRUCTION & PACKING IMFORMATION

1. HUMMER H1

2. 710×140×125MM INNER BOX

3. 725×300×390MM OUTER BOX (6 PCS/1BOX)

4. HUMMER H2

5. 1320×140×125MM INNER BOX

6. 1335×300×390MM OUTER BOX (6 PCS/1BOX)

7. HUMMER H3

8. 1650×140×125MM INNER BOX

9. 1665×300×270MM OUTER BOX (4 PCS/1BOX)

1

2

3

4

5

6

7

8

9

CONTACT INFORMATION

ADDRESS

COMPANY ADDRESS ROOM 507, NO. 423 XINCUN RD. PUTUO DIST. SHANGHAI, CHINA

FACTORY ADDRESS NO. 238 HENGZHAI RD. SHESHAN TOWN, SONGJIANG DIST. SHANGHAI, CHINA

TELEPHONE NO.

BUSINESS OFFICE +86 21 66057753

+86 21 66057783

QUALITY DEPARTMENT +86 21 66057753-8015

COMPLAINT & ADVISE +86 21 66057753-8008

MAIL BOX

PRODUCTS CONSULTANT WILLIAM@PNQLIGHTING.COM DAVID@PNQLIGHTING.COM

QUALITY & DESIGN INFORMATION JACK@PNQLIGHTING.COM

CONTACT INFORMATION