19Th C. Rococo Iron & Crystal Sm 18' Chandelier -...
Transcript of 19Th C. Rococo Iron & Crystal Sm 18' Chandelier -...
RESTORATION HARDWARE19th C. ROCOCO IRON & CRYSTAL CHANDELIER SMALL
6'8:9�+4)259+*
/:+39����*/'-8'3����*+9)8/6:/54�������7:?�
�'� 0[TIZOUT�(U^�4UZ�OTIR[JKJ����2(��3/4�,/>:;8+�8':+*
�
�(� )KOROTM�.UUQ �
�)� 3U[TZOTM�9IXK]Y�4UZ�OTIR[JKJ�
��9KZ
�*� )URRGX �
�+��)GTUV_ �
�+��
�,� .GTM�9ZXGOMNZ �
�-� 7[OIQ�2OTQ �
�.� )NGOT �
�/� =OXK�4[Z �
�0� )GTJRK�9RKK\K �
�1� ([RH�9VGXK ���
�2� (UJ_ �
:5�'99+3(2+
685*;):�*+9)8/6:/54 General material: Glass & IronHeight: 55.0 cmDiameter: 46.0 cmWeight: 6.0 kgGrounded / Hardwired
IMPORTANT SAFETY INSTRUCTIONS:1. Use an authorized and certified electrician for consultation and installation.2. This fixture has been rated for 6 x 25-watt maximum E12 standard bulb.
4. The ceiling must have at least the capacity of 5 times the weight of the ceiling light. For this light at least a ceiling capacity of 30kg is required.
=GXTOTMY 1. Turn-off electricity supply at main circuit panel before installing. Do not connectelectricity supply until your ceiling light is fully assembled and installed.
5. The manufacturer and distributor accepts no liability for incorrect installation.
2. All wires are connected. Do not remove the ceiling light from its packaging by pullingon the power cord, as a bad connection may result.3. To reduce the risk of fire, electrical shock, or personal injury, always turn off theceiling light and allow it to cool prior to replacing light bulb. Do not touch bulb whenfixture is turned on or look directly at light bulb. Keep flammable materials away fromlight bulb.4. Deviation from instructions may result in a risk of fire or electric shock.
)'8+�/49:8;):/549 1. Make sure that the power is turned off and bulb has cooled before handling.2. Wipe clean with a dry cloth / mild soapy solution. Do not use corrosive cleaners.3. The cable/cord of this ceiling light cannot be replaced: If the cable is damaged, donot use the light.
6. For indoor use only.
+4</8543+4: Special waste handling may be required. Please contact your local authorities for moreinformation.
3. To avoid the risk of fire, do not exceed the recommended wattage.
1 3 4 5
36PCS
14mmX7pcs2
50X38mm
14mmX1pc 14mmX1pc
40mm
6PCS 2PCS
63X43mm
14mmX1pc
12PCS
14mmX11pcs
14mmX1pc
12PCS
614mmX pcs
7
63X43mm 63X43mm
6PCS
6PCS
63X43mm
12
4
5
3
1
1
6 35
4
7
8
1. Carefully remove all parts from the box and remove all plastic covering.2. Turn OFF power to the junction box where the ceiling light will be installed.3. Loosen the bolt of hang straight (F) and remove the collar (D) from the hang straight(F) by unscrewing it. Then insert (D) into canopy (E1) and re-attach collar (D) to hangstraight (F). Tighten the bolt of the hang straight (F).4. Unlock the quick link (G) at the opposite end of the chain (H) to attach the chandelierbody (L).5. Attach the ceiling hook (B) to the ceiling with mounting screws (C).6. Attach end of the collar (D) to the ceiling hook (B).7. Connect the ground wire from the fixture to the ground junction box wire (A) (Usuallythe green or bare wire) and wrap the connection with electrical tape. Connect the hotwire to the hot junction box wire (A) (Usually black or smooth) with a plastic wire nut (I)and wrap the connection with electrical tape. Connect the neutral wire to the neutraljunction box wire (A) (Usually white or ribbed) with a plastic wire nut (I) and wrap theconnection with electrical tape.8. Move the canopy (E1) up to the ceiling, then fasten the bolt (E2).
14. Restore power to the junction box and test ceiling light fixture.
12. Position glass dishes (7) and candle sleeves (J), and hang the crystals as perdrawing on left.13. Fasten lightbulbs (K) to the lampholders.
9. Loosen metal part (O) and detach round lid (N) from body (L), then loosen the nut (M)and detach from the body (L).10. Fix glass dish (8) onto body (L), and secure with nut (M).11. Re-attach round lid (N) to body (L) and secure with metal part (O).
8
1PC
7. Keep away from children.
RESTORATION HARDWARE19th ROCOCO MD 26IN CHDLR CRYS
6'8:9�+4)259+*
/:+39����*/'-8'3����*+9)8/6:/54�������7:?�
�'� 0[TIZOUT�(U^�4UZ�OTIR[JKJ����2(��3/4�,/>:;8+�8':+*
�
�(� )KOROTM�.UUQ �
�)� 3U[TZOTM�9IXK]Y�4UZ�OTIR[JKJ�
��9KZY
�*� )URRGX ��+��
)GTUV_ ��+��
�,� .GTM�9ZXGOMNZ �
�-� 7[OIQ�2OTQ �
�.� )NGOT �
�/� =OXK�4[Z �
�0� )GTJRK�9RKK\K ��
�1� ([RH�9VGXK
�2� (UJ_ �
:5�'99+3(2+
685*;):�*+9)8/6:/54 General material: Chinese Crystal & IronHeight: 65.0 cmDiameter: 70.0 cmWeight: 9.0 kgGrounded / Hardwired
IMPORTANT SAFETY INSTRUCTIONS:1. Use an authorized and certified electrician for consultation and installation.2. This fixture has been rated for 12 x 25-watt maximum E12 standard bulb.
4. The ceiling must have at least the capacity of 5 times the weight of the ceiling light. For this light at least a ceiling capacity of 45kg is required.
=GXTOTMY 1. Turn-off electricity supply at main circuit panel before installing. Do not connectelectricity supply until your ceiling light is fully assembled and installed.
5. The manufacturer and distributor accepts no liability for incorrect installation.
2. All wires are connected. Do not remove the ceiling light from its packaging by pullingon the power cord, as a bad connection may result.3. To reduce the risk of fire, electrical shock, or personal injury, always turn off theceiling light and allow it to cool prior to replacing light bulb. Do not touch bulb whenfixture is turned on or look directly at light bulb. Keep flammable materials away fromlight bulb.4. Deviation from instructions may result in a risk of fire or electric shock.
)'8+�/49:8;):/549 1. Make sure that the power is turned off and bulb has cooled before handling.2. Wipe clean with a dry cloth / mild soapy solution. Do not use corrosive cleaners.3. The cable/cord of this ceiling light cannot be replaced: If the cable is damaged, donot use the light.
6. For indoor use only.
+4</8543+4: Special waste handling may be required. Please contact your local authorities for moreinformation.
3. To avoid the risk of fire, do not exceed the recommended wattage.
�3� -RGYY�(UZZRK �
10
10
����
1. Carefully remove all parts from the box and remove all plastic covering.2. Turn OFF power to the junction box where the ceiling light will be installed.3. Loosen the bolt of hang straight (F) and remove the collar (D) from the hang straight(F) by unscrewing it. Then insert (D) into canopy (E1) and re-attach collar (D) to hangstraight (F). Tighten the bolt of the hang straight (F).
6. Attach the ceiling hook (B) to the ceiling with mounting screws (C).7. Attach end of the collar (D) to the ceiling hook (B).8. Connect the ground wire from the fixture to the ground junction box wire (A) (Usuallythe green or bare wire) and wrap the connection with electrical tape. Connect the hotwire to the hot junction box wire (A) (Usually black or smooth) with a plastic wire nut (I)and wrap the connection with electrical tape. Connect the neutral wire to the neutraljunction box wire (A) (Usually white or ribbed) with a plastic wire nut (I) and wrap theconnection with electrical tape.9. Move the canopy (E1) up to the ceiling, then fasten the bolt (E2).10. Loosen metal part (P) and detach round lid (O) from body (L), then loosen the nut(N) and detach from the body (L).
13. Position glass dishes (9) and candle sleeves (J), and hang the crystals as perdrawing on left.
4. Unlock the quick link (G) on the opposite end of the chain (H) and attach to the hangstraight (F) on the glass bottle (M).5. Unlock the quick link (G) on the opposite end of the glass bottle (M) and attach tothe hang straight (F) on body (L).
14. Fasten lightbulbs (K) to the lampholders.
11. Fix glass dish (10) onto body (L), and secure with nut (N).12. Re-attach round lid (O) to body (L) and secure with metal part (P).
15. Restore power to the junction box and test ceiling light fixture.
7. Keep away from children.
RESTORATION HARDWARE19th ROCOCO IRON & CRYSTAL LG32 CHANDELIER
6'8:9�+4)259+*
/:+39����*/'-8'3����*+9)8/6:/54�������7:?�
�'� 0[TIZOUT�(U^�4UZ�OTIR[JKJ����2(��3/4�,/>:;8+�8':+*
�
�(� )KOROTM�.UUQ �
�)� 3U[TZOTM�9IXK]Y�4UZ�OTIR[JKJ�
��9KZY
�*� )URRGX ��+��
)GTUV_ ��+��
�,� .GTM�9ZXGOMNZ �
�-� 7[OIQ�2OTQ �
�.� )NGOT �
�/� =OXK�4[Z �
�0� )GTJRK�9RKK\K
�1� ([RH�9VGXK
�2� (UJ_ �
:5�'99+3(2+
685*;):�*+9)8/6:/54 General material: Chinese Crystal & IronHeight: 70.0 cmDiameter: 83.0 cmWeight: 14.0 kgGrounded / Hardwired
IMPORTANT SAFETY INSTRUCTIONS:1. Use an authorized and certified electrician for consultation and installation.2. This fixture has been rated for 18 x 25-watt maximum E12 standard bulb.
4. The ceiling must have at least the capacity of 5 times the weight of the ceiling light. For this light at least a ceiling capacity of 70kg is required.
=GXTOTMY 1. Turn-off electricity supply at main circuit panel before installing. Do not connectelectricity supply until your ceiling light is fully assembled and installed.
5. The manufacturer and distributor accepts no liability for incorrect installation.
2. All wires are connected. Do not remove the ceiling light from its packaging by pullingon the power cord, as a bad connection may result.3. To reduce the risk of fire, electrical shock, or personal injury, always turn off theceiling light and allow it to cool prior to replacing light bulb. Do not touch bulb whenfixture is turned on or look directly at light bulb. Keep flammable materials away fromlight bulb.4. Deviation from instructions may result in a risk of fire or electric shock.
)'8+�/49:8;):/549 1. Make sure that the power is turned off and bulb has cooled before handling.2. Wipe clean with a dry cloth / mild soapy solution. Do not use corrosive cleaners.3. The cable/cord of this ceiling light cannot be replaced: If the cable is damaged, donot use the light.
6. For indoor use only.
+4</8543+4: Special waste handling may be required. Please contact your local authorities for moreinformation.
3. To avoid the risk of fire, do not exceed the recommended wattage.
�3� -RGYY�(UZZRK �
90
1 2 3 4 5 7 8 9
18PCS
1 2
34
56
7
8
1 1
11
4
9
1
1. Carefully remove all parts from the box and remove all plastic covering.2. Turn OFF power to the junction box where the ceiling light will be installed.3. Loosen the bolt of hang straight (F) and remove the collar (D) from the hang straight(F) by unscrewing it. Then insert (D) into canopy (E1) and re-attach collar (D) to hangstraight (F). Tighten the bolt of the hang straight (F).
6. Attach the ceiling hook (B) to the ceiling with mounting screws (C).7. Attach end of the collar (D) to the ceiling hook (B).8. Connect the ground wire from the fixture to the ground junction box wire (A) (Usuallythe green or bare wire) and wrap the connection with electrical tape. Connect the hotwire to the hot junction box wire (A) (Usually black or smooth) with a plastic wire nut (I)and wrap the connection with electrical tape. Connect the neutral wire to the neutraljunction box wire (A) (Usually white or ribbed) with a plastic wire nut (I) and wrap theconnection with electrical tape.9. Move the canopy (E1) up to the ceiling, then fasten the bolt (E2).10. Loosen metal part (P) and detach round lid (O) from body (L), then loosen the nut(N) and detach from the body (L).
13. Position glass dishes (9) and candle sleeves (J), and hang the crystals as perdrawing on left.
4. Unlock the quick link (G) on the opposite end of the chain (H) and attach to the hangstraight (F) on the glass bottle (M).5. Unlock the quick link (G) on the opposite end of the glass bottle (M) and attach tothe hang straight (F) on body (L).
14. Fasten lightbulbs (K) to the lampholders.
11. Fix glass dish (10) onto body (L), and secure with nut (N).12. Re-attach round lid (O) to body (L) and secure with metal part (P).
15. Restore power to the junction box and test ceiling light fixture.
��
����
7. Keep away from children.
RESTORATION HARDWARE19th ROCOCO IRON & CRYSTAL XL 40 CHANDELIER
6'8:9�+4)259+*
/:+39����*/'-8'3����*+9)8/6:/54�������7:?�
�'� 0[TIZOUT�(U^�4UZ�OTIR[JKJ����2(��3/4�,/>:;8+�8':+*
�
�(� )KOROTM�.UUQ �
�)� 3U[TZOTM�9IXK]Y�4UZ�OTIR[JKJ�
��9KZY
�*� )URRGX ��+��
)GTUV_ ��+��
�,� .GTM�9ZXGOMNZ �
�-� 7[OIQ�2OTQ �
�.� )NGOT �
�/� =OXK�4[Z �
�0� )GTJRK�9RKK\K ��
�1� ([RH�9VGXK ����
�2� (UJ_ �
:5�'99+3(2+
685*;):�*+9)8/6:/54 General material: Chinese Crystal & IronHeight: 133.0 cmDiameter: 102.0 cmWeight: 22.0 kgGrounded / Hardwired
IMPORTANT SAFETY INSTRUCTIONS:1. Use an authorized and certified electrician for consultation and installation.2. This fixture has been rated for 25 x 25-watt maximum E12 standard bulb.
4. The ceiling must have at least the capacity of 5 times the weight of the ceiling light. For this light at least a ceiling capacity of 110kg is required.
=GXTOTMY 1. Turn-off electricity supply at main circuit panel before installing. Do not connectelectricity supply until your ceiling light is fully assembled and installed.
5. The manufacturer and distributor accepts no liability for incorrect installation.
2. All wires are connected. Do not remove the ceiling light from its packaging by pullingon the power cord, as a bad connection may result.3. To reduce the risk of fire, electrical shock, or personal injury, always turn off theceiling light and allow it to cool prior to replacing light bulb. Do not touch bulb whenfixture is turned on or look directly at light bulb. Keep flammable materials away fromlight bulb.4. Deviation from instructions may result in a risk of fire or electric shock.
)'8+�/49:8;):/549 1. Make sure that the power is turned off and bulb has cooled before handling.2. Wipe clean with a dry cloth / mild soapy solution. Do not use corrosive cleaners.3. The cable/cord of this ceiling light cannot be replaced: If the cable is damaged, donot use the light.
6. For indoor use only.
+4</8543+4: Special waste handling may be required. Please contact your local authorities for moreinformation.
3. To avoid the risk of fire, do not exceed the recommended wattage.
2
3
4
5
5
6
7
6
8
19
10
3
11
6
1
1
2
2
2
132
2
2
14
2
15
14mmX1pc 14mmX1pc 14mmX7pcs 14mmX13pcs
14mm
1 2 3 4 5 614mmX7pcs 14mmX9pcs
14mmX1pc 14mmX1pc 14mmX7pcs
14mmX3pcs
14mmX8pcs14mmX13pcs
14mmX2pcs 14mmX2pcs 14mmX11pcs14mmX4pcs
50X38mm 63X43mm
63X43mm63X43mm 63X43mm 63X43mm
63X43mm63X43mm
63X43mm63X43mm
40mm
14mmX1 pc
14mmX1 pc
14mmX1 pc 14mm
X1 pc
14mmX1 pc
1 2 3 4 5 6
8 9 10 11 12 13
7
114PCS 12PCS 6PCS 12PCS 24PCS 6PCS
6PCS 6PCS 6PCS 6PCS1PC 1PC
14mmX7pcs 14mmX9pcs
50mm
14mmX7pcs
48PCS1
PCS251
PC1
5
�3� -RGYY�(UZZRK �
1. Carefully remove all parts from the box and remove all plastic covering.2. Turn OFF power to the junction box where the ceiling light will be installed.3. Loosen the bolt of hang straight (F) and remove the collar (D) from the hang straight(F) by unscrewing it. Then insert (D) into canopy (E1) and re-attach collar (D) to hangstraight (F). Tighten the bolt of the hang straight (F).
6. Attach the ceiling hook (B) to the ceiling with mounting screws (C).7. Attach end of the collar (D) to the ceiling hook (B).8. Connect the ground wire from the fixture to the ground junction box wire (A) (Usuallythe green or bare wire) and wrap the connection with electrical tape. Connect the hotwire to the hot junction box wire (A) (Usually black or smooth) with a plastic wire nut (I)and wrap the connection with electrical tape. Connect the neutral wire to the neutraljunction box wire (A) (Usually white or ribbed) with a plastic wire nut (I) and wrap theconnection with electrical tape.9. Move the canopy (E1) up to the ceiling, then fasten the bolt (E2).10. Loosen metal part (P) and detach round lid (O) from body (L), then loosen the nut(N) and detach from the body (L).
13. Position glass dishes (14) and candle sleeves (J), and hang the crystals as perdrawing on left.
4. Unlock the quick link (G) on the opposite end of the chain (H) and attach to the hangstraight (F) on the glass bottle (M).5. Unlock the quick link (G) on the opposite end of the glass bottle (M) and attach tothe hang straight (F) on body (L).
14. Fasten lightbulbs (K) to the lampholders.
11. Fix glass dish (15) onto body (L), and secure with nut (N).12. Re-attach round lid (O) to body (L) and secure with metal part (P).
15. Restore power to the junction box and test ceiling light fixture.
7. Keep away from children.