19365579 Sharp AQUOS LC32404652LE700UN Service Manual
-
Upload
oraliamunoz -
Category
Documents
-
view
207 -
download
25
Transcript of 19365579 Sharp AQUOS LC32404652LE700UN Service Manual
-
SERVICE MANUAL
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining thesafety and performance of the set.
This document has been published to be used forafter sales service only.The contents are subject to change without notice.
SAFETY PRECAUTIONIMPORTANT SERVICE SAFETY PRECAUTION...............iPRECAUTIONS A PRENDRE LORS DE LA REPARATION............................................... iiPRECAUTIONS FOR USING LEAD-FREE SOLDER ........................................................... iii
CHAPTER 1. SPECIFICATIONS[1] SPECIFICATIONS (LC-32LE700UN)............. 1-1[2] SPECIFICATIONS (LC-40/46/52LE700UN) ............. 1-2
CHAPTER 2. OPERATION MANUAL[1] Parts Name (LC-32LE700UN) ....................... 2-1[2] Parts Name (LC-40/46/52LE700UN) ............. 2-3[3] OPERATION MANUAL .................................. 2-5
CHAPTER 3. DIMENSIONS[1] DIMENSIONS (LC-32LE700UN).................... 3-1[2] DIMENSIONS (LC-40LE700UN).................... 3-2[3] DIMENSIONS (LC-46LE700UN).................... 3-3[4] DIMENSIONS (LC-52LE700UN).................... 3-4
CHAPTER 4. REMOVING OF MAJOR PARTS[1] REMOVING OF MAJOR PARTS ................... 4-1
CHAPTER 5. ADJUSTMENT[1] ADJUSTMENT PROCEDURE....................... 5-1
[2] PUBLIC MODE SETTING PROCEDURE.......5-17
CHAPTER 6. TROUBLESHOOTING TABLE[1] TROUBLESHOOTING TABLE ......................6-1
CHAPTER 7. MAJOR IC INFORMATIONS[1] MAJOR IC INFORMATIONS .........................7-1
CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK DIAGRAM[1] OVERALL WIRING DIAGRAM......................8-1[2] SYSTEM BLOCK DIAGRAM (LC-32LE700UN)........8-2[3] SYSTEM BLOCK DIAGRAM (LC-40/46/52LE700UN)........8-3
CHAPTER 9. PRINTED WIRING BOARD ASSEMBLIES[1] KEY Unit, R/C, LED Unit, ICON Unit .............9-1[2] MAIN Unit ......................................................9-2
CHAPTER 10. SCHEMATIC DIAGRAM[1] DESCRIPTION OF SCHEMATIC DIAGRAM .........10-1[2] SCHEMATIC DIAGRAM (LC-32LE700UN) ........10-2[3] SCHEMATIC DIAGRAM (LC-46/46/52LE700UN).........10-18
Parts Guide
CONTENTS
No. S79B2LC32L70U
LCD COLOR TELEVISION
LC-32LE700UNLC-40LE700UNLC-46LE700UNLC-52LE700UNMODELS
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-inal condition and only parts identical to those specified should be used.
LC-32/40/46/52LE700UN
-
LC-32/40/46/52LE700UNLC32LE700UN Service Manual
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETUShock Hazard)Before returning the safety checks:
3. Inspect all lead dresand check that hardother metal parts in t
4. Inspect all protectiveinsulation materials,covers or shields, isoinsulators, etc.
5. To be sure that no shthe following manne
Plug the AC cord dir
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-leled by a 0.15F capacitor in series with all exposed metal cabinetparts and a known earth ground, such as electrical conduit or elec-trical ground connected to an earth ground.
Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-sitivity or measure the AC voltage drop across the resistor.
Connect the resistor connection to all exposed metal parts having areturn to the chassis (antenna, metal cabinet, screw heads, knobsand control shafts, escutcheon, etc.) and measure the AC voltagedrop across the resistor.
/////////////////////////////////////
SAFETY NOTICEMany electrical and mspecial safety-related ch
These characteristics acan protection affordedreplacement componen
Replacement parts whicidentified in this manuaare identified by " " aand Schematic Diagram
/////////////////////////////////////
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
CAUTION : FOR CONTINUED PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.F7001 (250V 2.5A) (LC-32LE700UN)
F7002 (250V 2
F7001 (250V 5
F7002 (250V 5
F7001 (250V 6
F7002 (250V 6 i
RNING THE RECEIVER (Fire &
receiver to the user, perform the following
s to make certain that leads are not pinched,ware is not lodged between the chassis andhe receiver.
devices such as non-metallic control knobs, cabinet backs, adjustment and compartmentlation resistor-capacitor networks, mechanical
ock hazard exists, check for leakage current inr.
ectly into a 120 volt AC outlet.
All checks must be repeated with the AC cord plug connectionreversed. (If necessary, a nonpolarized adaptor plug must be usedonly for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) ormore is excessive and indicates a potential shock hazard whichmust be corrected before returning the monitor to the owner.
//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
echanical parts in LCD color television havearacteristics.
re often not evident from visual inspection, nor by them be necessarily increased by usingts rated for higher voltage, wattage, etc.
h have these special safety characteristics arel; electrical components having such featuresnd shaded areas in the Replacement Parts Lists.
For continued protection, replacement parts must be identical to thoseused in the original circuit.
The use of a substitute replacement parts which do not have the samesafety characteristics as the factory recommended replacement partsshown in this service manual, may create shock, fire or other hazards.
//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
.5A) (LC-32LE700UN)
A) (LC-40LE700UN)
A) (LC-40LE700UN)
.3A) (LC-46/52LE700UN)
.3A) (LC-46/52LE700UN)
DVM
AC SCALE
1.5k ohm10W
TO EXPOSEDMETAL PARTS
CONNECT TOKNOWN EARTHGROUND
0.15 F
TEST PROBE
-
LC-32/40/46/52LE700UNPRECAUTIONS A PRENDRE LORS DE LA REPARATION
De nombreuses picesseur ACL prsentent decurit, qui ne sont souvtion ne peut pas trepices de remplacemenetc.Les pices de remplaceidentifies dans ce manparticularits sont identiliste des pices de remp
AVERTISSEMENT
1.
2.
3.
4.
5.
///////////////////////////////////////
///////////////////////////////////////
Ne peut effectuer la rparation qu' un technicien spcialis qui s'est parfaitement accoutum toute vrification de scurit et aux
conseils suivants.
N'entreprendre aucune modification de tout circuit. C'est danger-eux.
Dbrancher le rcepteur avant toute rparation.
Inspecter tous les fane soient pas pincssis et les autres pic
Inspecter tous les dcommande non-mtvercles ou blindagesde rsistancecapacit
S'assurer qu'il n'y aifuite de courant, de l
Brancher le cordon drant de 120V. (Ne pcet essai).
A l'aide de deux fils pinces, brancher une rsistance de 1.5 k10 watts en parallle avec un condensateur de 0.15F en srieavec toutes les pices mtalliques exposes du coffret et une terreconnue comme une conduite lectrique ou une prise de terrebranche la terre.
Utiliser un voltmtre CA d'une sensibilit d'au moins 5000/V pourmesurer la chute de tension en travers de la rsistance.
Toucher avec la sonde d'essai les pices mtalliques exposes quiprsentent une voie de retour au chssis (antenne, coffret mtalli-que, tte des vis, arbres de commande et des boutons, cusson,etc.) et mesurer la chute de tension CA en-travers de la rsistance.Toutes les vrifications doivent tre refaites aprs avoir invers lafiche du cordon d'alimentation. (Si ncessaire, une prised'adpatation non polarise peut tre utilise dans le but de termin-
PRECAUTION: POUR LA PROTECTION CON-
TINUE CONTRE LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE
VERIFICATIONS
CHOC ELECTRI
Avant de rendre le rc
tions suivantes.
AVIS POUR LA SE
F7001 (250V 2.5A) (LC-32LE700UN)
F7002 (250V 2.5A) (LC-32LE700UN)
F7001 (250V 5A) (LC-40LE700UN)
F7002 (250
F7001 (250
F7002 (250ii
, lectriques et mcaniques, dans les tlvi-s caractristiques spciales relatives la s-ent pas videntes vue. Le degr de protec-ncessairement augmente en utilisant dest talonnes pour haute tension, puissance,
ment qui prsentent ces caractristiques sontuel; les pices lectriques qui prsentent cesfies par la marque " " et hachures dans lalacement et les diagrammes schmatiques.
Pour assurer la protection, ces pices doivent tre identiques cellesutilises dans le circuit d'origine. L'utilisation de pices qui n'ont pasles mmes caractristiques que les pices recommandes par l'usine,indiques dans ce manuel, peut provoquer des lectrocutions, incen-dies, radiations X ou autres accidents.
//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
isceaux de cbles pour s'assurer que les filsou qu'un outil ne soit pas plac entre le chs-es mtalliques du rcepteur.
ispositifs de protection comme les boutons dealliques, les isolants, le dos du coffret, les cou-de rglage et de compartiment, les rseaux, les isolateurs mcaniques, etc.
t pas de danger d'lectrocution en vrifiant laa facon suivante:
'alimentation directem-ent une prise de cou-as utiliser de transformateur d'isolation pour
er ces vrifications.)La tension de pointe mesure ne doit pas dpasser 0.75V (corre-spondante au courant CA de pointe de 0.5mA).Dans le cas contraire, il y a une possibilit de choc lectrique quidoit tre supprime avant de rendre le rcepteur au client.
CONTRE L'INCEN-DIE ET LE
QUE
epteur l'utilisateur, effectuer les vrifica- DVM
ECHELLE CA
1.5k ohm10W
0.15 F
SONDE D'ESSAI
AUX PIECESMETALLIQUESEXPOSEES
BRANCHER A UNETERRE CONNUE
CURITE
V 5A) (LC-40LE700UN)
V 6.3A) (LC-46/52LE700UN)
V 6.3A) (LC-46/52LE700UN)
-
LC-32/40/46/52LE700UNPRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder PWBs of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due
As the melting point bit, if you are not fam
Soldering As the melting point
solder wettability, yopeeled off or the masteady soldering con
Lead-free solder conrequired.
If a different type of s
When the tip of the s
Be careful when rep
Lead-free wire solder fo
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
PARTS CODE PRZHNDAi123250EZHNDAi126500EZHNDAi12801KE iii
to cracks.
of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we recommend you to use a dedicated solderingiliar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, and as it has pooru may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may beximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm thedition.
tains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
older stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
oldering bit is blackened during use, file it with steel wool or fine sandpaper.
lacing parts with polarity indication on the PWB silk.
r servicing
RICE ANK
PART DELIVERY DESCRIPTION
BL J 0.3mm 250g (1roll)BK J 0.6mm 500g (1roll)BM J 1.0mm 1kg (1roll)
-
LC-32/40/46/52LE700UNLC32LE700UN Service Manual CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS (LC-32LE700UN)
Item Model: LC-32LE700UN
LCDpanel
Size 32" Class (3135/64" Diagonal)
Resolution 2,073,600 pixels (1,920 1,080)
TVFunction
TV-standard (CCIR) American TV Standard ATSC/NTSC System
ReceivingChannel
VHF/UHF VHF 2-13ch, UHF 14-69ch
CATV 1-135ch (non-scrambled channel only)
Digital TerrestrialBroadcast (8VSB)
2-69ch
Digital cable*1
(64/256 QAM)1-135ch (non-scrambled channel only)
Aud
Audio out
Terminals
Rea
Side
OSD language
Power Requirem
Power Consump
Weight
Dimension*2
(W H D)
Operating tempe
*1Emergency ale
*2The dimensionaAs part of policyproduct improveunits. There ma
Optional A
The listed optionCrystal TelevisioAdditional optiofuture. When pucompatibility an1 1
io multiplex BTSC System
10W 2
r
INPUT 1 AV in, COMPONENT in
INPUT 2 COMPONENT in, S-VIDEO in
INPUT 4 ANALOG RGB (PC) in (15-pin mini D-sub female connector), Audio in ( 3.5 mm jack)
INPUT 6 HDMI in with HDCP, Audio in ( 3.5 mm jack)
INPUT 7 HDMI in with HDCP
INPUT 8 HDMI in with HDCP
ANT/CABLE 75 Unbalance, F Type 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)AUDIO Audio in ( 3.5 mm jack)
DIGITAL AUDIO OUTPUT Optical Digital audio output 1 (PCM/Dolby Digital)
OUTPUT Audio out
RS-232C 9-pin D-sub male connector
INPUT 3 AV in
INPUT 5 HDMI in with HDCP
SERVICE Software update
English/French/Spanish
ent AC 120 V, 60 Hz
tion 130 W (0.5 W Standby with AC 120 V)
TV + stand 26.5 lbs./12.0 kg
TV only 23.1 lbs./10.5 kg
TV + stand 3013/64 21
47/64 10
7/8 inch
TV only 3013/64 19
49/64 3
19/32 inch
rature +32F to +104F (0C to +40C)
rt messages via Cable are unreceivable.l drawings are shown on the inside back cover.of continuous improvement, SHARP reserves the right to make design and specification changes forment without prior notice. The performance specification figures indicated are nominal values of productiony be some deviations from these values in individual units.
ccessory
al accessory is available for the Liquidn. Please purchase it at your nearest shop.nal accessories may be available in the nearrchasing, please read the newest catalogue ford check the availability.
Part name Model number
Wall mount bracket AN-37AG5
-
LC-32/40/46/52LE700UN[2] SPECIFICATIONS (LC-40/46/52LE700UN)
Item Model: LC-40LE700UN Model: LC-46LE700UN Model: LC-52LE700UN
LCDpanel
Size 40" Class (40" Diagonal) 46" Class (4563/64" Diagonal) 52" Class (52
1/32" Diagonal)
Resolution 2,073,600 pixels (1,920 1,080)
TVFunction
TV-standard (CCIR) American TV Standard ATSC/NTSC System
ReceivingChannel
VHF/UHF VHF 2-13ch, UHF 14-69ch
CATV 1-135ch (non-scrambled channel only)
Digital TerrestrialBroadcast (8VSB)
2-69ch
Digital cable*1
(64/256 QAM)1-135ch (non-scrambled channel only)
Audio multiplex BTSC System
Audio out 10W 2
Terminals
Rea
Side
OSD language
Power Requirem
Power Consump
Weight
Dimension*2
(W H D)(inches)
Operating tempe
*1Emergency ale
*2The dimensionaAs part of policyproduct improveunits. There ma
Optional A
The listed optionCrystal TelevisioAdditional optiofuture. When pucompatibility an1 2
r
INPUT 1 AV in, COMPONENT in
INPUT 2 COMPONENT in, S-VIDEO in
INPUT 4 ANALOG RGB (PC) in (15-pin mini D-sub female connector), Audio in ( 3.5 mm jack)
INPUT 6 HDMI in with HDCP, Audio in ( 3.5 mm jack)
INPUT 7 HDMI in with HDCP
INPUT 8 HDMI in with HDCP
ANT/CABLE 75 Unbalance, F Type 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)AUDIO Audio in ( 3.5 mm jack)
DIGITAL AUDIO OUTPUT Optical Digital audio output 1 (PCM/Dolby Digital)
ETHERNET Network connector
OUTPUT Audio out
RS-232C 9-pin D-sub male connector
INPUT 3 AV in
INPUT 5 HDMI in with HDCP
USB Photo/Music mode, Software update
English/French/Spanish
ent AC 120 V, 60 Hz
tion160 W(0.5 W Standby with AC 120 V)
200 W(0.5 W Standby with AC 120 V)
250 W(0.5 W Standby with AC 120 V)
TV + stand 30.9 lbs./14.0 kg 47.4 lbs./21.5 kg 57.3 lbs./26.0 kg
TV only 26.5 lbs./12.0 kg 40.8 lbs./18.5 kg 50.7 lbs./23.0 kg
TV + stand 3761/64 26
3/16 12
3/8 43
9/32 29
11/64 13
61/64 48
3/4 32
13/64 13
61/64
TV only 3761/64 24
3/32 3
41/64 43
9/32 27
3/32 3
45/64 48
3/4 30
1/8 3
43/64
rature +32F to +104F (0C to +40C)
rt messages via Cable are unreceivable.l drawings are shown on the inside back cover.of continuous improvement, SHARP reserves the right to make design and specification changes forment without prior notice. The performance specification figures indicated are nominal values of productiony be some deviations from these values in individual units.
ccessory
al accessory is available for the Liquidn. Please purchase it at your nearest shop.nal accessories may be available in the nearrchasing, please read the newest catalogue ford check the availability.
Part name Model number
Wall mountbracket
AN-37AG2 (for LC-40LE700UN)
Attachment AN-37P30 (for LC-40LE700UN)
Wall mountbracket
AN-52AG4(for LC-46LE700UN/LC-52LE700UN)
-
LC-32/40/46/52LE700UNLC32LE700UN Service Manual CHAPTER 2. OPERATION MANUAL
[1] Parts Name (LC-32LE700UN)
TV (Front)
OPC sensor*
POWER indicator
Remote control sensor
OPC indicator
TV (R
*1 Extern*2 Button*3 Conne*4 Details
The illu
Blue Illumination LED * OPC: Optical Picture Control2 1
ear/Side)
AC INPUTterminal
POWERbutton
MENUbutton
INPUTbutton
Channelbuttons(CH / )
Volume
buttons
(VOL / )
RS-232C terminal
DIGITAL AUDIOOUTPUT terminal
INPUT 7 terminal(HDMI)
INPUT 8 terminal(HDMI)
INPUT 6 terminal (HDMI)
INPUT 4 terminal (PC-IN)
AUDIO terminal (shared for INPUT 4 and INPUT 6) *4
Antenna/Cable in
INPUT 1 terminals
INPUT 2 terminals
AUDIO OUTPUTterminals
INPUT 3terminals
SERVICEterminal
INPUT 5terminal(HDMI)
*1
*2
*3
*1
al equipment connection.operations.cting the AC cord.on the PC Audio Select function.
strations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
-
LC-32/40/46/52LE700UN
32
1 17
5
6
4
8
18
19
7
10
9
11
1312
15
14
16
1 TV POWER: Switch the TV power on or enter standby.
2 DISPLAY: Display the channel information.
3 SOURCE POWER: Turns the power of the external equipment
on and off.
4 External equipment operational buttons: Operate the external
equipment.
5 09: Set the channel.
6 (DOT)
7 INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2, INPUT 3,
INPUT 4, INPUT 5, INPUT 6, INPUT 7, INPUT 8)
8 VOL / : Set the volume.
9 POWER SAVING: Select Power Saving settings.
10 FREEZE: Set the still image. Press again to return to normal
screen.
11 EXIT: Turn off the menu screen.
12 OPTION: Display the AQUOS LINK MENU screen. This button
will function only when AQUOS LINK is used.
Remote Control Unit
When us2 2
20
21
22
23
24
26
27
28
30
25
29
13 REC STOP: Stops one touch recording. This button will function
only when AQUOS LINK is used.
14 SLEEP: Set the sleep timer.
15 SURROUND: Select Surround settings.
16 AUDIO: Selects the MTS/SAP or the audio mode during multi-
channel audio broadcasts.
17 FUNCTION: Switches the remote control for TV, CBL/SAT, VCR,
DVD and AUDIO operation. Indicator lights up for the current
mode.
* To enter the code registration mode, you need to press
FUNCTION and DISPLAY at the same time.
18 LIGHT :When this button is pressed, some buttons (for
example,VOL / and CH / ) on the remote control unit will
light. The lighting will turn off if no operations are performed within
about 5 seconds. This button is used for performing operations in
low-light situations.
19 VIEW MODE: Select the screen size.
20 ENT: Jumps to a channel after selecting with the 09 buttons.
21 FLASHBACK: Return to the previous channel or external input
mode.
22 CH / : Select the channel.
23 MUTE: Mute the sound.
24 MENU: Display the menu screen.
25 / / / , ENTER: Select a desired item on the screen.
26 RETURN: Return to the previous menu screen.
27 FAVORITE CH
A, B, C, D: Select 4 preset favorite channels in 4 different
categories.
While watching, you can toggle the selected channels by pressing
A, B, C and D.
28 FAVORITE: Set the favorite channels.
29 CC: Display captions from a closed-caption source.
30 AV MODE: Select an audio or video setting.
(When the input source is TV, INPUT 1, 2 or 3: STANDARD,
MOVIE, GAME, USER, AUTO, DYNAMIC (Fixed), DYNAMIC.
When the input source is INPUT 4, 5, 6, 7 or 8: STANDARD,
MOVIE, GAME, PC, USER, AUTO, DYNAMIC (Fixed), DYNAMIC)
ing the remote control unit, point it at the TV.
-
LC-32/40/46/52LE700UN[2] Parts Name (LC-40/46/52LE700UN)
TV (Front)
OPC sensor*
POWER indicator
Remote control sensor
OPC indicator
TV (Rear/Side)
*2
*1 External*2 Button op*3 Connecti*4 Details o
The illustr The exam
* OPC: Optical Picture ControlBlue Illumination LED2 3
AC INPUTterminal
INPUT 3terminals
USBterminal
INPUT 5terminal(HDMI)
*1
*3
*1
RS-232C terminal
DIGITAL AUDIOOUTPUT terminal
INPUT 7 terminal(HDMI)
INPUT 8 terminal(HDMI)
INPUT 6 terminal (HDMI)
INPUT 4 terminal (PC-IN)
AUDIO terminal (shared for INPUT 4 and INPUT 6) *4
Antenna/Cable in
INPUT 1 terminals
INPUT 2 terminals
AUDIO OUTPUTterminals
ETHERNET terminal
POWERbutton
MENUbutton
INPUTbutton
Channelbuttons(CH / )
Volume
buttons
(VOL / )
equipment connection.erations.ng the AC cord.n the PC Audio Select function.
ations in this operation manual are for explanation purposes and may vary slightly from the actual operations.ples used throughout this manual are based on the LC-46LE700UN model.
-
LC-32/40/46/52LE700UN
32
1 18
5
6
4
9
19
20
7
11
10
12
1413
16
15
17
8
1 TV POWER: Switch the TV power on or enter standby.
2 DISPLAY: Display the channel information.
3 SOURCE POWER: Turns the power of the external equipment
on and off.
4 External equipment operational buttons: Operate the external
equipment.
5 09: Set the channel.
6 (DOT)
7 NET: Switches the display to the Sidebar Widget, TV +Web, Web
or TV screen.
8 INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2, INPUT 3,
INPUT 4, INPUT 5, INPUT 6, INPUT 7, INPUT 8, USB)
9 VOL : Set the volume.
10 POWER SAVING: Select Power Saving settings.
11 FREEZE: Set the still image. Press again to return to normal
screen.
Remote Control Unit
When u
/2 4
21
22
23
24
25
27
28
29
31
26
30
12 EXIT: Turn off the menu screen.
13 OPTION: Display the AQUOS LINK MENU screen. This button
will function only when AQUOS LINK is used.
14 REC STOP: Stops one touch recording. This button will function
only when AQUOS LINK is used.
15 SLEEP: Set the sleep timer.
16 SURROUND: Select Surround settings.
17 AUDIO: Selects the MTS/SAP or the audio mode during multi-
channel audio broadcasts.
18 FUNCTION: Switches the remote control for TV, CBL/SAT, VCR,
BD/DVD and AUDIO operation. Indicator lights up for the current
mode.
* To enter the code registration mode, you need to press
FUNCTION and DISPLAY at the same time.
19 LIGHT :When this button is pressed, some buttons (for
example, VOL and CH ) on the remote control unit will
light. The lighting will turn off if no operations are performed within
about 5 seconds. This button is used for performing operations in
low-light situations.
20 VIEW MODE: Select the screen size.
21 ENT: Jumps to a channel after selecting with the 09 buttons.
22 FLASHBACK: Return to the previous channel or external input
mode.
23 CH : Select the channel.
24 MUTE: Mute the sound.
25 MENU: Display the menu screen.
26 , ENTER: Select a desired item on the screen.
27 RETURN: Return to the previous menu screen.
28 FAVORITE CH
A, B, C, D: Select 4 preset favorite channels in 4 different
categories.
While watching, you can toggle the selected channels by pressing
A, B, C and D.
29 FAVORITE: Set the favorite channels.
30 CC: Display captions from a closed-caption source.
31 AV MODE: Select an audio or video setting.
(When the input source is TV, INPUT 1, 2 or 3: STANDARD,
MOVIE, GAME, USER, AUTO, DYNAMIC (Fixed), DYNAMIC.
When the input source is INPUT 4, 5, 6, 7 or 8: STANDARD,
MOVIE, GAME, PC, USER, AUTO, DYNAMIC (Fixed), DYNAMIC)
sing the remote control unit, point it at the TV.
/ /
/
/ / /
-
LC-32/40/46/52LE700UN[3] OPERATION MANUAL
1. LC-32LE700UN
Attaching the Stand
Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
Attach the stand in the correct direction.Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
1 Confirm that there are 12 screws (all the same size)supplied with the stand unit.
2 Set th
Attach
Inserton theHoldthen
1
1
2
1
2
3
3 Insert the stand into the openings on the bottomof the TV.
Insert and tighten the 4 screws into the 4 holeson the rear of the TV.2 5
e post for the stand unit onto the box.
the base to the post.
and tighten the 8 screws into the 8 holesbottom of the base.the stand unit securely with one hand, andtighten the screws.
FRONT
2
3
1
Screws
1
1
2 2Screws
Soft cushion
To detach the stand, perform the steps in reverse order.
-
LC-32/40/46/52LE700UN2. LC-40/46/52LE700UN
1 Confirm that there are 12 screws (all the same size)supplied with the stand unit.
2 1 Set the post for the stand unit onto the box.
2 Attach
3 Inserton the
Holdtight
3
1
Attaching the Stand
Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
3 1 Insert the stand into the openings on the bottomof the TV.
2 Insert and tighten the 4 screws into the 4 holeson the rear of the TV.
CAUTION
Attach the stand in the correct direction.Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.2 6
the base to the post.
and tighten the 8 screws into the 8 holesbottom of the base.
the stand unit securely with one hand, and thenen the screws.
FRONT
2
3
1
Screws
1
1
2 2Screws
Soft cushion
To detach the stand, perform the steps in reverse order.
-
LC-32/40/46/52LE700UNLC32LE700UN Service Manual CHAPTER 3. DIMENSIONS
[1] DIMENSIONS (LC-32LE700UN)
Unit: inch (mm)
15 1/8 (384)
3 19/323 9/32
163/ 64
(50)
1949/ 64(502)
77/ 8(200)55/ 16
(135)
2147/ 64(552)3 1
(91)(83)
10 7/8 (276)
30 13/64 (767)
27 9/16 (700)
7 7/8 (200)
1517/ 32
(394.5)
129/ 16(319)
3 19/32(91)
6 25/32(172)
AN-37AG5
3 13/64(81)
-
LC-32/40/46/52LE700UN[2] DIMENSIONS (LC-40LE700UN)
Unit: inch (mm)37 61/64 (964)
263/ 16(665)
243/ 32(612)
23/ 32
(53)
1457/ 64(378)
18 1/2 (470)
34 61/64 (887.8)
1945/ 64
(500.35)
645/ 64
(170)
1113/ 16
(300)3 2
11 13/16(300)
3 41/64(92.5)
3 41/64(92.5)
3 29/32(99)
6 63/64(177.1)
3 11/32(84.6)
12 3/8(314)
AN-37AG2
AN-37P30+
-
LC-32/40/46/52LE700UN[3] DIMENSIONS (LC-46LE700UN)
Unit: inch (mm)153/ 4(400)
657/ 64
(175)
43 9/32 (1099)
2911/ 64(741)
273/ 32(688)
23/ 32
(53)
40 19/64 (1023.4)
2243/ 64
(575.6)
1625/ 64(416)
22 31/64 (571)
40 19/64 (1023.4)
2243/ 64
(575.6)3 3
4 37/64(116)
AN-52AG4
15 3/4 (400)
13 61/64(354)
3 45/64(94)
611/32(161)
2 41/64(67)
3 45/64(94)
-
LC-32/40/46/52LE700UN[4] DIMENSIONS (LC-52LE700UN)
153/ 4(400)
657/ 64
(175)
48 3/4 (1238)301/ 8(765)
3213/ 64(818)
23/ 32
(53)
45 9/16 (1157.0)
2541/ 64
(651.0)
1727/ 32(453)
22 31/64 (571)
Unit: inch (mm)3 4
15 3/4 (400)
13 61/64(354)
6 5/16(160)
3 3/4(95)
3 43/64(93)
2 9/16(65)
4 17/32(115)
AN-52AG4
3 3/4(95)
-
LC-32/40/46/52LE700UNLC32LE700UN Service Manual CHAPTER 4. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS
1. Removing of Stand Unit and Rear Cabinet Assy.(LC-32LE700UN)
1. Remove the 4 lock screws and detach the Stand Unit .
2. Remove the 1 lock screw , 5 lock screws , 8 lock screws and detach the Rear Cabinet Assy.
4 1
-
LC-32/40/46/52LE700UN(LC-40/46/52LE700UN)
3. Remove the 4 lock screws and detach the Stand Unit .
4. Remove the 1 lock screw , 6 lock screws , 6 lock screws and detach the Rear Cabinet Assy.
4 2
-
LC-32/40/46/52LE700UN2. Removing of Side Terminal Cover Assy, Main PWB Shield, Speaker-L/R and Bottom Cover Assy.1. Remove the rivet and detach the Shield Main .
2. Detach the Side Terminal Cover Assy .
3. Remove the 3 lock screws , 2 lock screws and 4 lock screws and detach the Main PWB Shield .
4. Disconnect SP wire.
5. Detach the Speaker-L ,Speaker-R .
6. Remove the 1 lock screw (LC-32LE700UN Only) , 2 hooks and detach the Bottom Cover Assy .
4 3
Hook Hook
HookHook
-
LC-32/40/46/52LE700UN3. Removing of Connectors, R/C, LED Unit, ICON Unit and Control Bottom Cover Assy.1. Disconnect the following connectors from the MAIN Unit. (RA, LB, PD, KM, LP, LW)
2. Disconnect the following connectors from the POWER Unit. (PD, PL, LB, LA1, LA2, LA3 (except for LC-32/40LE700UN))
3. Disconnect the following connectors from the LCD Control Unit. (LP, LW, PL)
4. Detach the R/C, LED Unit .
5. Detach the ICON Unit .
6. Disconnect the following connectors from the R/C, LED Unit. (RA, IM)
7. Disconnect the following connector from the ICON Unit. (IM)
8. Detach the Control Bottom Cover Assy .
9. Disconnect the KEY Unit from the Control Bottom Cover Assy and disconnect the connection cord from the KM Connector.
4 4
-
LC-32/40/46/52LE700UN4. Removing of POWER Unit and MAIN Unit.
1. Remove the 4 lock screws (LC-32LE700UN) , 6 lock screws (LC-40/46/52LE700UN) and detach the POWER Unit .
2. Remove the 3 lock screws and detach the MAIN Unit .
4 5
-
LC-32/40/46/52LE700UN5. Removing of Center Angle.LC-32/40LE700UN
1. Remove the 6 lock screws (LC-32LE700UN) , 14 lock screws (LC-40LE700UN) and detach the Center Angle .
LC-46/52LE700UN
2. Remove the 4 lock screws and 8 lock screws and detach the VESA Angle and Center Angle .
4 6
-
LC-32/40/46/52LE700UN6. Removing of Bezel Assy, Panel Chassis Assy, Optical Sheet, Lens Sheet, Diffusion Plate, Back Light Chas-sis and LCD Control Unit (LC-32LE700UN).NOTE: A clean booth is required for repair of the component units and/ or parts (LCD Panel HIRAKI, LED PWB etc.) inside the LCD panel module
unit.
1. Remove the 10 lock screws ,10 lock screws and detach the Bezel Assy .
2. Detach the 32 LCD Panel Module and Panel Chassis Assy .
3. Detach the Optical sheet and Lens Sheet and Diffusion Plate .
4. Remove the 16 Push Rivets and 4 Support Pins and detach the Reflection Sheet .
5. Remove the 32 Push Rivets .
6. Remove the 8 Terminators and 8 connections and detach the 4 LED8 PWB1 Units and 4 LED8 PWB2 Units .
7. Detach the 4 LED5 PWB1 Units and 4 LED5 PWB2 Units .
8. Disconnect the connecting cords from the 8 connectors of the LED5 PWB1/2 Unit.
9. Detach the Back Light Chassis .
10.Detach the 2 Connecting Cord and 2 Ferrite Core .
11.Remove the 6 lock s
4 7
crews and detach the LCD Control Unit
-
LC-32/40/46/52LE700UN7. Handling notes (LC-32LE700UN). 1. Set and connect LED-PWBs.
2. Peel off the laminatio
RUNTKA595WJ01 / WJ02
RUNTKA598WJ01 / WJ02Top Side
Bottom Side (C-PWB side)
RUNTKA595WJ01
RUNTKA595WJ02
RUNTKA595WJ01
RUNTKA595WJ02
RUNTKA595WJ01
RUNTKA595WJ02
RUNTKA595WJ01
RUNTKA595WJ02
INSIDE of
BL-CHASSIS
WIRE HARNESS
Top Side
Bottom Side (C-PWB side)
RUNTKA598WJ01
RUNTKA598WJ02
RUNTKA598WJ01
RUNTKA598WJ02
RUNTKA598WJ01
RUNTKA598WJ02
RUNTKA598WJ01
RUNTKA598WJ02
*Same for other 7 lines.Set and connect LED-PWBs
Boss fitt
(showing in bl
RUNTKA595WJ01/02 RUNTKA598WJ01/02
Boss of
BL-CHASSIS
LED-PW
(arrow m
Peel off4 8
n film of LENS SHEET on the both sides.
Connect LED-PWBs
ing
ue circles)
LED-PWB
TERMINATOR
is AttachedB set direction
ark to harness side)
LED-PWB set direction
(arrow mark to harness side)
Insert the connector horizontally mutually.
Do not add inadequate power.
FRONT BACK
the lamination filmof LENS SHEET on the both sides.
Peel off the lamination film.
-
LC-32/40/46/52LE700UN8. Removing of Bezel Assy, Panel Chassis Assy, Lens Sheet, Diffusion Plate, Back Light Chassis and LCDControl Unit (LC-40LE700UN).NOTE: A clean booth is required for repair of the component units and/ or parts (LCD Panel HIRAKI, LED PWB etc.) inside the LCD panel module
unit.
1. Remove the 8 lock screws ,12 lock screws and detach the Bezel Assy .
2. Remove the 4 Clip and detach the 40 LCD Panel Module and Panel Chassis Assy .
3. Detach the 2 Lens Sheet and Diffusion Plate .
4. Remove the 21 Push Rivets and 8 Support Pins and detach the Reflection Sheet .
5. Remove the 54 Rivets .
6. Remove the 9 Terminators and 18 connections and detach the 10 LED6 PWB1 Units and 8 LED6 PWB2 Units .
7. Detach the 5 LED5 PWB1 Units and 4 LED5 PWB2 Units .
8. Disconnect the connecting cords from the 9 connectors of the LED5 PWB1/2 Unit.
9. Detach the Back Light Chassis .
10.Detach the 2 Connecting Cord and 2 Ferrite Core .
11.Remove the 6 lock s4 9
crews and detach the LCD Control Unit
-
LC-32/40/46/52LE700UN9. Handling notes (LC-40LE700UN). 1. Set and connect LED-PWBs.
2. Peel off the laminatio
Set LED-PWB(6LED)9LED-PWB(6LED)RUNTKA596WJ015RUNTKA596WJ024
LED-PWB(6LED)RUNTKA596WJ015RUNTKA596WJ024
Set LED-PWB(6LED)
It being alternatedRUNTKA***WJ01and RUNTKA***WJ02.
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02RUNTKA***WJ01
RUNTKA***WJ02RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
Note: Set sequential LED-PWB as below.
bott(C-PW
Top side
Insert the connector horizontally mutually.Do not add inadequate power.
bottom(C-PWB) side
Peel off4 10
n film of LENS SHEET on the both sides.
9
omB) side
Top side
FRONT BACK
the lamination filmof LENS SHEET on the both sides.
Peel off the lamination film.
-
LC-32/40/46/52LE700UN10. Removing of Bezel Assy, Panel Chassis Assy, Lens Sheet, Diffusion Plate, Back Light Chassis and LCDControl Unit (LC-46LE700UN).NOTE: A clean booth is required for repair of the component units and/ or parts (LCD Panel HIRAKI, LED PWB etc.) inside the LCD panel module
unit.
1. Remove the 10 lock screws ,16 lock screws and detach the Bezel Assy .
2. Remove the 4 Clip and detach the 46 LCD Panel Module and Panel Chassis Assy .
3. Detach the 2 Lens Sheet and Diffusion Plate .
4. Remove the 32 Push Rivets and 11 Support Pins and detach the Reflection Sheet .
5. Remove the 66 Push Rivets .
6. Remove the 11 Terminators and 22 connections and detach the 6 LED8 PWB1 Units , 5 LED8 PWB2 Units .6 LED6 PWB1 Unit and 5 LED6 PWB2 Unit .
7. Detach the 6 LED5 PWB1 Units and 5 LED5 PWB2 Units .
8. Disconnect the connecting cords from the 11 connectors of the LED5 PWB1/2 Unit.
9. Detach the Back Light Chassis .
10.Detach the 2 Conne
11.Remove the 6 lock s4 11
cting Cord and 2 Ferrite Core .
crews and detach the LCD Control Unit .
-
LC-32/40/46/52LE700UN11. Handling notes (LC-46LE700UN). 1. Set and connect LED-PWBs.
2. Peel off the laminatio
RUNTKA595WJ01 / WJ02 RUNTKA596WJ01 / WJ02 RUNTKA598WJ01 / WJ02
CAUTION
It being alternatedRUNTKA***WJ01and RUNTKA***WJ02.
Top Side
Bottom Side (C-PWB side)
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
INSIDE ofBL-CHASSIS
Set and connect LE
Boss fitt(showing in blu
Boss ofBL-CHASSIS
WIRE HARNESS
LED-PWB(arrow ma
Peel off4 12
n film of LENS SHEET on the both sides.
*Same for other lines.
Connect LED-PWBs
D-PWBs
inge circles)
RUNTKA595WJ** RUNTKA596WJ** RUNTKA598WJ**
LED-PWB
TERMINATOR
is Attached
set directionrk to harness side)
LED-PWB set direction(arrow mark to harness side)
LED-PWB set direction(arrow mark to harness side)
Insert the connector horizontally mutually.Do not add impossible power.
FRONT BACK
the lamination filmof LENS SHEET on the both sides.
Peel off the lamination film.
-
LC-32/40/46/52LE700UN12. Removing of Bezel Assy, Panel Chassis Assy, Lens Sheet, Diffusion Plate, Back Light Chassis and LCDControl Unit (LC-52LE700UN).NOTE: A clean booth is required for repair of the component units and/ or parts (LCD Panel HIRAKI, LED PWB etc.) inside the LCD panel module
unit.
1. Remove the 12 lock screws ,16 lock screws and detach the Bezel Assy .
2. Remove the 6 Clip and detach the 52 LCD Panel Module and Panel Chassis Assy .
3. Detach the 2 Lens Sheet and Diffusion Plate .
4. Remove the 43 Push Rivets and 11 Support Pins and detach the Reflection Sheet .
5. Remove the 72 Push Rivets .
6. Remove the 12 Terminators and 24 connections and detach the 12 LED8 PWB1 Units and 12 LED8 PWB2 Units .
7. Detach the 6 LED6 PWB1 Units and 6 LED6 PWB2 Units .
8. Disconnect the connecting cords from the 12 connectors of the LED6 PWB1/2 Unit.
9. Detach the Back Light Chassis .
10.Detach the 2 Connecting Cord and 2 Ferrite Core .
11.Remove the 6 lock s4 13
crews and detach the LCD Control Unit
-
LC-32/40/46/52LE700UN13. Handling notes (LC-52LE700UN). 1. Set and connect LED-PWBs.
2. Peel off the laminatio
RUNTKA596WJ01 / WJ02 RUNTKA598WJ01 / WJ02
Top Side
Bottom Side (C-PWB side)
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
RUNTKA***WJ01
RUNTKA***WJ02
Set and connect LED-PWBs
Boss(showing in
Boss ofBL-CHASSIS
TERMINATOR is Attached
RUNTKA596WJ**
RUNTKA598WJ**
The insertion process of the LED6-PWB(1&2) and LED8-PWB(1&2)
CAUTION
It being alternatedRUNTKA***WJ01and RUNTKA***WJ02.
RUNTKA598WJ01 / WJ02
and TERMINATOR
RUNTKA596WJ01 / WJ02 RUNTKA598WJ01 / WJ02
RUNTKA598WJ01 / WJ02
and TERMINATOR
LED(arr
blowing way
Peel4 14
n film of LENS SHEET on the both sides.
*Same on the other line.
fittingblue circles
LED-PWB
LED-PWB set direction(arrow mark to harness side)
LED-PWB set direction(arrow mark to harness side)
Insert the connector horizontally mutually.Do not add impossible power.
-PWB set directionow mark to harness side)
Ionized air blowers
blowing way
FRONT BACK
off the lamination filmof LENS SHEET on the both sides.
Peel off the lamination film.
-
LC-32/40/46/52LE700UN14. Handling notesPlease note the following handling notes enough, when this product is used.
Moreover, please execute an enough evaluation (temperature rise and I/F match, etc.) and confirmations while installed in your product.
1. Since this product uses LED (light emitting diode). note the static electricity at handling, and do the countermeasure against static electricity of thebody grounding etc.
2. Please do not give the stress by the fall, the impact, and the accumulation of product etc. when you handle the product.
3. The installation hole must be fixed at grade, and stresses such as Warp and Twist must not join the board when you install the board. Moreover,please do not work with the part LED, the diffusion lens, and the reflection sheet.
Please do not touch by the hand with the bord..the bar code and the serial number part...
* Otherwise, it causes scratches/dirt adhesion.
4. Please put in parallel to the connector and horizontally, and insert it in the interior surely when you insert the connector. Moreover, please usegloves, etc. not to touch the connector terminal directory by bare-handed.
5. Please turn off the power supply and the signal input to the board unit surely, when this product is inserted in or removes from the connector.
* Otherwise, it causes the part damage.
6. Additionally, please observe notes of usual electronic parts.
7. When the LED unit is handling and built into the equipment, long-term storage in the oxidation or reduced gas atmosphere or the use of use ofmaterials such as thsion and discoloratio
8. Time between turnin4 15
e reagent that generates these steams of the oxidation or reduced gas, the solvent, adhesives, and resins might cause corro-n.
g on power and stabilizing brightness and Chromaticity. : 5min (60mA, at 25C).
-
LC-32/40/46/52LE700UNLC32LE700UN Service Manual CHAPTER 5. ADJUSTMENT
[1] ADJUSTMENT PROCEDUREThe adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment isrequired due to part replacement, make an adjustment according to the following procedure.
1. After replacement of any PWB unit and/or IC for repair, please note the following. When replacing the following units, make sure to prepare the new units loaded with updated software.
When replacing the LCD control PWB, perform the VCOM adjustment.
2. Upgrading of each microprocessor softwareCAUTION: Never POWER OFF the unit when software upgrade is ongoing.
Otherwise the system may be damaged beyond recovery.
2.1. Software versioThe model employs the
Main software (pleas
Monitor microproces
The main software, mon
The followings are the p
2.2. Main software v
2.2.1 Get ready befo USB Memory of 128
PC running on Wind
USB Memory reader
The file system of a
Use the USB memor
2.2.2 PreparationsTo upgrade the main so
Follow the steps below
1. Copy the file HLNRB
NOTE: In the USB Mem
Now the USB M
MAIN Unit: DUNTKF282FM02 (LC-32LE700UN)DUNTKF282FM01 (LC-40/46/52LE700UN)5 1
n upgrade following software.
e use a software version after HLNRBxxx.USB (32HLNRCxxx.USB). )
sor software (please use a software version after HLNRA0x.USB and HLNRMxxx.BIN.)
itor microprocessor software can be upgraded by using a general-purpose USB Memory.
rocedures for upgrading, explained separately for the main software, monitor microprocessor software.
ersion upgrade
re you startMB or higher capacity.
ows 98/98SE/ME/2000/XP operating system.
/writer or PC with a USB port.
USB memory is FAT. (FAT32 supports)
y without other functions. (lock and memory reader...etc)
ftware, it is necessary to get ready the USB Memory for version upgrade before you start.
and create the USB Memory for version upgrade.
xxx.USB (32HLNRCxxx.USB). for version upgrade to the root directory (folder) of the USB Memory.
ory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
emory for version upgrade is ready.
-
LC-32/40/46/52LE700UN2.2.3 How to upgrade the software1. Unplug the AC cord.
2. Insert the USB Memory for version upgrade (prepared as above) into the service socket located Right side of Main Board terminals, under INPUT3terminal.
3. Plug in the AC cord with power button pressed down after 5 seconds, unpress the power button.
4. After the unit startup, the system upgrade screen as shown below appears within 20-40 seconds.
5. Even a single failure
NOTE: In the event of a
6. Upon completion of screen. The version
7. Unplug the AC cord
8. Now the software ve
NOTE: When you are dsoftware version
LE700UN5 2
in the process will trigger the upgrade failure screen.
failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
the whole process, the upgrade success screen as shown below appears. You can check the new software version on thisinformation appears after the upgrade is complete.
and remove the USB Memory for version upgrade.
rsion upgrade is complete.
one with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main information.
LE700UN
LE700UN
-
LC-32/40/46/52LE700UN2.3. Monitor microprocessor software version upgradeCreate the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the Main software versionupgrade.
Copy the file HLNRVA0x.USB and HLNRMxxx.BIN (named temporarily) for monitor microprocessor software version upgrade to the USB memory.
2.3.1 How to upgrade the software1. Unplug the AC cord.
2. Insert the USB Memory for version upgrade (prepared as above) into the service socket located Right side of Main Board terminals, under INPUT3terminal.
3. Plug in the AC cord with power button pressed down.
4. After 5 seconds, unpress the power button.
CAUTION: The moment this operation is done, the upgrading of the monitor microprocessor software starts. While the upgrade is ongoing, neverpower off the unit. Otherwise the upgrade will fail and the system may be serious damaged beyond recovery (inability to start).
After the monitor microprocessor software is upgraded, also perform the 'Industry Init'.
5. After the unit startup, the upgrade starts. The power led will blink continuously. Also, an upgrade screen will be shown during a minor upgrade.
6. If the upgrade fails, p
NOTE: In the event of acause.
7. Up on completion ofscreen was shown a
8. Unplug the AC cord
9. Now the software ve
NOTE: When you are ditor microproces5 3
ower led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.
transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the
the whole process, power and OPC LED will blink alternately. Also, the upgrade success screen will be shown if upgradet 5.
and remove the USB Memory for version upgrade.
rsion upgrade is complete.
one with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-sor software version information and panel size information.
LE700UN
LE700UN
LE700UN
-
LC-32/40/46/52LE700UN3. Entering and exiting the adjustment process mode1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) While holding down the VOL () and INPUT keys at a time, plug in the AC cord of the main unit to turn on the power.
The letter appears on the screen.
3) Next, hold down the VOL () and CH ( ) keys at a time.
(The VOL () and CH ( ) keys should be pressed and held until the display appears.)
Multiple lines of blue characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When thepower was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If thesettings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode1) Key operation
*Input mode is switc
2) Description of displa
Remote controller kCH ( / )VOL (+/)Cursor (UP/DOWN)Cursor (LEFT/RIGHT)INPUTENTER5 4
hed automatically when relevant adjustment is started so far as the necessary input signal is available.
y
ey Main unit key FunctionCH ( / ) Moving an item (line) by one (UP/DOWN)VOL (+/) Changing a selected item setting (+1/ 1)
Turing a page (PREVIOUS/NEXT) Changing a selected line setting (+10/ 10) Input switching (toggle switching) Executing a function
(2) Current selected input(3) Current color system(1) Current page/
(4) Destination(5) LCD Panel size/Speaker type
Total pages
1/40 INPUT5 AUTO USA 40_UNDER
MAIN Version 1.09 (U 2009/07/07 1A)
BOOT Version HLNR 100
Monitor/Monitor BOOT Version 1.02/1.00
LCD Con Version
LED TCON Version
0900626000T0001
16
EQ DATA CHECKSUM ROM(7) Parameters
TEMPERATURE 7B
LAMP ERROR 0
MONITOR ERR CAUSE 0
NORMAL STANDBY CAUSE 0
ERROR STANDBY CAUSE 1) 0 2) 0 3) 00H 0M 0H 0M 0H 0M
4) 0 5) 00H 0M 0H 0M
(6) Adjustmentprocess menuheader
-
LC-32/40/46/52LE700UN5. List of adjustment process mode menuThe character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page Line Item Description Remarks (adjustment detail, etc.)1 1 MAIN Version Main software version
2 BOOT Version3 Monitor/Monitor BOOT Version Monitor and monitor boot software version4 LCD Con Version LCD controller software version Versions are always 090626000T0001.5 LED TCON Version6 EQ DATA CHECKSUM Audio data checksum7 TEMPERATURE Panel temperature8 LAMP ERROR Number of termination due to lamp error9 MONITOR ERR CAUSE
10 NORMAL STANDBY CAUSE Refer to *1 under the list for details11 ERROR STANDBY CAUSE Refer to *2 under the list for details
2 1 INDUSTRY INIT Initialization to factory settings2 INDUSTRY INIT(-Hotel)3 PUBLIC MODE Public mode4 Center Acutime Accumulated main operation time5 RESE6 Backl7 RESE8 LAMP9 VIC X
10 VIC Y11 VIC C12 VIC S13 VIC R
3 1 N3582 N3583 N3584 N3585 TUNE6 N3587 N3588 N3589 TUNE
10 TUNE11 TUNE
4 1 TUNE2 TUNE3 TUNE4 TUNE5 INSPE6 HDMI7 HDMI
5 1 COMP2 COMP3 COMP4 COMP5 COMP6 COMP7 COMP8 COMP
6 1 COMP2 COMP3 COMP4 COMP5 COMP6 COMP7 COMP8 COMP5 5
T Resetight Acutime Accumulated monitor operation timeT Reset ERROR RESET Reset LAMP ERRORPOS X-coordinate setting for VIC READPOS Y-coordinate setting for VIC READOLOR Collected color data setting for VIC READIGNAL TYPE Signal type setting for VIC READEAD Picture level acquisition function Level appears in green on the upper right ALL ADJ(INPUT1) CVBS and TUNER signal level adjustment ALL ADJ(INPUT3) MAIN ADJ(INPUT1) CVBS signal level adjustment MAIN ADJ(INPUT3)R DAC ADJ TUNER signal level adjustment
CONTRAST A_GAIN CONTRAST D_GAIN CONTRAST OFFSETR CONTRAST A_GAINR CONTRAST D_GAINR CONTRAST OFFSETR VCHIP TEST(69ch) Tuning test and VCHIP test (69ch)R VCHIP TEST(7ch) Tuning test and VCHIP test (7ch)R VCHIP TEST(10ch) Tuning test and VCHIP test (10ch)R VCHIP TEST(15ch) Tuning test and VCHIP test (15ch)CT USB TERM
EDID WRITE CEC TEST15K ADJ(INPUT1) Component 15K picture level adjustment (main)15K ADJ(INPUT2)15K Y A_GAIN15K Cb A_GAIN15K Cr A_GAIN15K Y OFFSET15K Cb OFFSET15K Cr OFFSET33K ADJ(INPUT1) Component 33K picture level adjustment (main)33K ADJ(INPUT2)33K Y A_GAIN33K Cb A_GAIN33K Cr A_GAIN33K Y OFFSET33K Cb OFFSET33K Cr OFFSET
-
LC-32/40/46/52LE700UN
7 1 ANALOG RGB ADJ Analog RGB picture level adjustment2 R A_GAIN3 G A_GAIN4 B A_GAIN5 R OFFSET6 G OFFSET7 B OFFSET
8 1 VCOM ADJ VCOM adjustment value9 1 FRC ON/OFF
10 1 LEV1 Standard value 1 Adjustment gradation setting.2 LEV2 Standard value 23 LEV3 Standard value 34 LEV4 Standard value 45 LEV5 Standard value 56 LEV6 Standard value 6
11 1 MG1R WB adjustment Point 1, R adjustment value Parameter for six-point adjustment2 MG1G WB adjustment Point 1, G adjustment value3 MG1B4 MG2R5 MG2G6 MG2B7 MG3R8 MG3G9 MG3B
12 1 MG4R2 MG4G3 MG4B4 MG5R5 MG5G6 MG5B7 MG6R8 MG6G9 MG6B
13 1 MODE2 POS 3 POS 4 POS 5 POS 6 POS 7 POS 8 POS 9 POS
10 POS 14 1 CD M
2 CD M3 CD M4 CD M5 CD M6 CD M7 CD M8 CD M
15 1 CALC2 RESE3 VAL14 VAL25 VAL36 VAL47 VAL58 VAL6
Page Line Item Description Remarks (adjustment detail, etc.)5 6
WB adjustment Point 1, B adjustment valueWB adjustment Point 2, R adjustment valueWB adjustment Point 2, G adjustment valueWB adjustment Point 2, B adjustment valueWB adjustment Point 3, R adjustment valueWB adjustment Point 3, G adjustment valueWB adjustment Point 3, B adjustment valueWB adjustment Point 4, R adjustment value Parameter for six-point adjustmentWB adjustment Point 4, G adjustment valueWB adjustment Point 4, B adjustment valueWB adjustment Point 5, R adjustment valueWB adjustment Point 5, G adjustment valueWB adjustment Point 5, B adjustment valueWB adjustment Point 6, R adjustment valueWB adjustment Point 6, G adjustment valueWB adjustment Point 6, B adjustment value
SELECTSELECTMINMID1MID2MID3MID4MID5MID6MAXINID1ID2ID3ID4ID5ID6AX
T
-
LC-32/40/46/52LE700UN
16 1 Audio Switch2 Flat Mode3 EEP STATUS INIT4 Input Trim DTV5 Input Trim ATV6 Input Trim Digital7 Input Trim Analog8 ATT1 Gain9 ATT2 Gain
10 ATT3 Gain17 1 Auto Volume Threshold
2 Auto Volume Ratio3 MBE Base Gain4 MBE Output Gain5 MBE BPF6 MBE Force otct Mode7 MBE Bass G Limit8 MPF
18 1 MVS 2 MVS 3 MVS 4 MVS 5 MVS 6 MVS 7 MVS
19 1 Bass 2 Bass 3 Bass 4 Bass 5 Bass 6 Bass 7 Treble8 Treble9 Treble
10 Treble11 Treble12 Treble
20 1 PEQ02 PEQ03 PEQ04 PEQ05 PEQ16 PEQ17 PEQ18 PEQ19 PEQ2
10 PEQ211 PEQ212 PEQ2
21 1 PEQ32 PEQ33 PEQ34 PEQ35 PEQ46 PEQ47 PEQ48 PEQ49 PEQ5
10 PEQ511 PEQ512 PEQ5
Page Line Item Description Remarks (adjustment detail, etc.)5 7
FCWidthXtalkClarityLR GainOutout GainBass GainFOCENTER ATTVol0 MAXVol60 MAXVol60 CENTERVol0 MINVol60 MIN CENTER ATT Vol0 MAX Vol60 MAX Vol60 CENTER Vol0 MIN Vol60 MIN F0 Q Gain G Limit F0 Q Gain G Limit F0 Q Gain G Limit F0 Q Gain G Limit F0 Q Gain G Limit F0 Q Gain G Limit
-
LC-32/40/46/52LE700UN
22 1 PEQ6 F02 PEQ6 Q3 PEQ6 Gain4 PEQ6 G Limit5 PEQ7 F06 PEQ7 Q7 PEQ7 Gain8 PEQ7 G Limit9 PEQ8 F0
10 PEQ8 Q11 PEQ8 Gain12 PEQ8 G Limit
23 1 AVC_L Fc2 AVC_L Target Level3 AVC_L Max Gain UP4 AVC_L Attack Rate5 AVC_L Release Rate6 AVC_7 AVC_8 AVC_9 AVC_
24 1 Sub V2 Sub V3 Sub V4 Sub V5 Sub V6 Clip L7 Clip L8 Clip L9 Clip L
10 Clip L25 1 PANN
2 PWM3 PWM4 PWM5 OSC 6 OSC
26 1 BRIG2 BRIG3 BRIG4 BRIG5 BRIG6 BRIG7 BRIG8 BRIG9 BRIG
10 BRIG11 BRIG12 BRIG
27 1 BRIG2 BRIG3 BRIG4 BRIG5 BRIG6 BRIG7 BRIG8 BRIG9 BRIG
10 BRIG11 BRIG
Page Line Item Description Remarks (adjustment detail, etc.)5 8
H Target LevelH Max Galn UPH Attack RateH Release Rateol. SPol. MONol. HPol. SWol. OPTevel SPevel MONevel HPevel SWevel OPTEL SELECT
FREQ DUTYFREQDUTYHTNESS DA0HTNESS DA1HTNESS DA2HTNESS DA3HTNESS DA4HTNESS DA5HTNESS DA6HTNESS DA7HTNESS DA8HTNESS DA9HTNESS DA10HTNESS DA11HTNESS DA12HTNESS DA13HTNESS DA14HTNESS DA15HTNESS DA16HTNESS DA17HTNESS DA18HTNESS DA19HTNESS DA20HTNESS DA21HTNESS DA22
-
LC-32/40/46/52LE700UN
28 1 BRIGHTNESS DA232 BRIGHTNESS DA243 BRIGHTNESS DA254 BRIGHTNESS DA265 BRIGHTNESS DA276 BRIGHTNESS DA287 BRIGHTNESS DA298 BRIGHTNESS DA309 BRIGHTNESS DA31
10 BRIGHTNESS DA3229 1 OPC33 ADLEVEL 0
2 OPC33 ADLEVEL 13 OPC33 ADLEVEL 24 OPC33 ADLEVEL 35 OPC33 ADLEVEL 46 OPC33 ADLEVEL 57 OPC33 ADLEVEL 68 OPC39 OPC3
10 OPC311 OPC312 OPC3
30 1 OPC32 OPC33 OPC34 OPC35 OPC36 OPC37 OPC38 OPC39 OPC3
10 OPC311 OPC3
31 1 OPC32 OPC33 OPC34 OPC35 OPC36 OPC37 OPC38 OPC39 OPC3
32 1 V6 OS2 V6 OS3 V6 OS4 V6 OS5 V6 OS6 V6 OS7 V6 OS
33 1 V5 OS2 V5 OS3 V5 OS4 V5 OS5 V5 OS6 V5 OS7 V5 OS
34 1 BL TE2 BL TE3 BL TD
35 1 MONI2 MONI3 MONI
RESE
Page Line Item Description Remarks (adjustment detail, etc.)5 9
3 ADLEVEL 73 ADLEVEL 83 ADLEVEL 93 ADLEVEL 103 ADLEVEL 113 ADLEVEL 123 ADLEVEL 133 ADLEVEL 143 ADLEVEL 153 ADLEVEL 163 ADLEVEL 173 ADLEVEL 183 ADLEVEL 193 ADLEVEL 203 ADLEVEL 213 ADLEVEL 223 ADLEVEL 233 ADLEVEL 243 ADLEVEL 253 ADLEVEL 263 ADLEVEL 273 ADLEVEL 283 ADLEVEL 293 ADLEVEL 303 ADLEVEL 31 THERMO 1 THERMO 2 THERMO 3 THERMO 4 THERMO 5 THERMO 6 THERMO 7 THERMO 1 THERMO 2 THERMO 3 THERMO 4 THERMO 5 THERMO 6 THERMO 7MP1MP2UTYTOR TIME OUTTOR MAX TEMPTOR ERROR CAUSE T
-
LC-32/40/46/52LE700UN
36 1 LCD TEST PATTERN2 LCD AGI TEST PATTERN3 LCD EVA TEST PATTERN4 YEL TEST PATTERN5 TV TEST PATTERN 16 TV TEST PATTERN 2
37 1 REGISTER ADDRESS LOWER2 READ/WRITE3 SLAVE ADDRESS4 REGISTER ADDRESS UPPER5 WRITE DATA UPPER6 WRITE DATA LOWER7 READ DATA UPPER8 READ DATA LOWER
38 1 KEY LOCK(1217)2 KOUTEI AREA ALL CLEAR3 A MODE AREA CLEAR4 BACK5 B MO6 EXEC
39 1 ERRO2 ERRO3 ERRO4 ERRO5 ERRO6 ERRO
RESE40 1 EEP S
2 EEP R3 MODL4 PANE5 SETT6 PANE7 PANE8 SHOR9 SHOR
10 CURR
*1 Details of P1.9 (NO2 No op3 No sig4 PC po5 PC po6 Off tim8 Comm
Page Line Item Description Remarks (adjustment detail, etc.)5 10
UP AREA CLEARDE AREA CLEARUTIONR STANDBY CAUSE1R STANDBY CAUSE2R STANDBY CAUSE3R STANDBY CAUSE4R STANDBY CAUSE5R STANDBY CAUSE TAVE Writing setting values to EEPROMECOVER Reading setting values from EEPROM NAMEL SIZEING FOR ADJ L LIMITL RANGE LIMITT CHECK MODET CHECK CURRENTENT SW
RMAL STANDBY CAUSE)eration off in the cause of no operation offnal off in the cause of no signal offwer management mode 1 in the cause of Standby mode MODE1wer management mode 2 in the cause of Standby mode MODE2er in the cause of SLEEP timerand from RS232C in the cause of command by RS-232C
-
LC-32/40/46/52LE700UN
6. Special features* STANDBY CAUSE (Page 1/40)
Display of a cause (code) of the last standby
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
* EEP SAVE (Page 40/40)
Storage of EEP adjustment value
* EEP RECOVER (Page 40/40)
Retrieval of EEP adjustment value from storage area
7. Microcomputer
7.1. Main microcom
7.2. Model/inch disc When writing the sub
Reference and settin
8. Signal adjustm
8.1. LCD section ad
*2 Details of P1.10 (ERROR STANDBY CAUSE)11 Prolonged unspecified-signal input in PC mode in the cause of continuous out of range, PC input mode17 Temperature error in the cause of abnormal temperature1A Monitor trouble detected in the cause of abnormal monitor mode22 LCD controller Rom error in the cause of software abnormality of LCD controller
Adjustment 1 Main microcompu
tor microcomputerwriting
Adjustment 1 Opposite bias adju
(LCD module adjuitem)5 11
software writing
puter/monitor microcomputer software writing (Main PWB: QPWBXF282WJZZ)
rimination writing (Main PWB: QPWBXF282WJZZ) microcomputer software, the model data is configured with the software from the USB memory mounted to the checker.
g change are enabled through the process menu and RS-232C communication.
ent
justment [LCD module adjustment]
item Adjustment conditions Adjustment procedureter/moni- software
Software Version Up
File version checkUSB memory check
1. Insert a USB memory for the main/monitor microcomputer into the service con-nector.2. Supply AC power and write the main software to IC8453 and the monitor micro-computer software to IC2002.3. Check that writing is normally completed and turn off the power.
CAUTION: When the USB memory is not inserted or reading error occurs, nothing is written. (The former models have read the main software from the writing jig. However, this model reads the main/monitor software from the USB memory.)
* When IC is failure Please exchange to another PWB unit when IC8453 (NAND Flash) is failure.(Because the software can't be written with USB memory, when the new IC is exchanged from broken IC)
item Adjustment conditions Adjustment procedurestmentstment
Adjustment in the center position of the panel(Except for LC-32LE700UM)
1. Enter the process mode using the process adjustment remote control.2. Select [VCOM ADJ] using the Channel , keys on the remote control.3. Press the Enter key to check that the pattern for adjustment is displayed.4. Make adjustment so that the flicker located in the center of the screen is mini-mized using the Volume +/- keys on the remote control.5. If the status is optimized in step 4, press the Enter key to turn off the pattern.
CAUTION: * Make adjustment without ANT signal (since the active backlight changes the brightness).
[Adjustment position]
1/4 3/4
1/2
1/2
-
LC-32/40/46/52LE700UN8.2. Video Signal adjustment Procedure
8.2.1 Signal check
Before adjustment, check that the adjustment jig and signal source are set for Sharp LCD US.
Signal generator level adjustment check (Adjust to the standard value level.)
8.2.2 Process mode
8.2.3 Composite N358 signal/tuner adjustment
8.2.4 Component 15
8.2.5 Component 33
Composite signal: 0.714Vp-p 0.02Vp-p (Pedestal to white level)15K component signal: Y level: 0.714Vp-p 0.02Vp-p (Pedestal to white level)
PB/PR level: 0.7Vp-p 0.02Vp-p33K component signal: Y level: 0.7Vp-p 0.02Vp-p (Pedestal to white level)
PB/PR level: 0.7Vp-p 0.02Vp-pAnalog RGB: RGB level: 0.7Vp-p 0.02Vp-p (Pedestal to white level)
Adjustment point Adjustment conditions Adjustment procedureProcess mode Enter the process adjustment mode using the process adjustment remote control.
Adjustment 1 Setting
2 Automatic adjustmcution
Adjustment 1 Setting
2 Automatic adjustmcution
Adjustment 1 Setting
2 Automatic adjustmcution5 12
K signal adjustment
K signal adjustment
point Adjustment conditions Adjustment procedureN358 signalUS-10ch
Send the N358 color bar (color saturation: 75%) signal to the Video 1 video input.Send the in-house signal (use US-10ch) to TUNER.
ent exe- Point the cursor to [ N358 ALL ADJ(INPUT1)] and press the [Enter] key.The adjustment is complete when [ N358 ALL ADJ(INPUT1) OK] is displayed.
point Adjustment conditions Adjustment procedure480i signal Send the 100% color bar signal to the Video 1 component input.
ent exe- Point the cursor to [ COMP15K ADJ(INPUT1)] and press the [OK] key.The adjustment is complete when [ COMP15K ADJ(INPUT1) OK] is displayed.
point Adjustment conditions Adjustment procedure1080i signal Send the 100% color bar signal to the Video 1 component input.
ent exe- Point the cursor to [ COMP33K ADJ(INPUT1)] and press the [OK] key.The adjustment is complete when [ COMP33K ADJ(INPUT1) OK] is displayed.
[Video input signal] [US-10CH]
100% white 100% white
75% Color saturation
100% white 0% black
480i100% color bar
100% Color saturation
100% white 0% black
1080i100% color bar
100% Color saturation
-
LC-32/40/46/52LE700UN8.2.6 Analog RGB signal adjustment
8.2.7 Tuner/V-CHIP adjustment
Adjustment point Adjustment conditions Adjustment procedure1 Setting Analog RGB Signal: XGA
(1024x768) 60HzSYNC: HV separate
Send the 100% color bar signal to the Video 4 analog RGB input.
2 Automatic adjustment exe-cution
Point the cursor to [ ANALOG RGB ADJ] and press the [OK] key.The adjustment is complete when [ ANALOG RGB ADJ OK] is displayed.
Adjustment point Adjustment conditions Adjustment procedure1 Setting
2 Automatic adjustmcution
100% white 0% black
XGA (1024x768)100% color bar5 13
NTSC RF signalUS-7(AIR)ch
Send the NTSC signal to the RF antenna input.
ent exe- Point the cursor to [ TUNER VCHIP TEST(*07ch)] and press the [OK] key. (* Adjust the selected channel to the in-house signal.)The adjustment is OK when [ A-OK(***.**)/VM-OK] is displayed in green.(NG when A-NG/VM-NG is displayed in red.)It is OK when the deviation from the center frequency is 0.0625MHz or less.
-
LC-32/40/46/52LE700UN9. White balance adjustment
9.1. White balance adjustment (For details about the adjustment procedure, refer to Kameyama Model Integrated MonitorWB Adjustment Specification V1.4.)
Adjustment point Adjustment conditions Adjustment procedure1 Setting 1) Set the set to the following conditions.
AV MODE: [DYNAMIC]Backlight: +16Active Backlight: OFFAging Time: Min. 60 minutes
2) Connect the set with the white balance adjustment jig.2 Automatic adjust-
ment execution[Command]Process modeKRSW0001KKT10037
SettingKYOF0000OSDS0001
[Adjustment procedure]1) Transmit the adjustment process code using the remote control.2) Set the point 6 to the specified gradation, specify the strongest color as the fixed
color, and adjust the RGB so that it becomes the standard value through negative adjustment.
3) Set the point 5 to the specified gradation, set the G correction value (3104 x G value of point 6/3712) (fractions rounded off), and adjust the RB so that it becomes the standard value.5 14
SBSL0016
Multi-point adjustment modeMSET0001
Point 6WBI60928MG6G****MG6B****MG6R****
Point 5WBI50776MG5G****MG5B****MG5R****
4) Set the point 4 to the specified gradation, set the G correction value (2240 x G value of point 6/3712) (fractions rounded off), and adjust the RB so that it becomes the standard value.
5) Set the point 3 to the specified gradation, set the G correction value (1232 x G value of point 6/3712) (fractions rounded off), and adjust the RB so that it becomes the standard value.
6) Set the point 2 to the specified gradation, set the G correction value (896 x G value of point 6/3712) (fractions rounded off), and adjust the RB pattern so that it becomes the standard value.
7) Set the point 1 to the specified gradation, set the G correction value (736 x G value of point 6/3712) (fractions rounded off), and adjust the RB so that it becomes the stan-dard value.
8) Write the adjustment value by the MSET0003 command and turn off the AC power.* RGB initial value of point 6: Set gradation 3712* RGB initial value of points 1 to 5: G correction value of each point
(At each point, adjustment is made so that the remainder of the RGB adjustment value/4 is equal.)
[Adjustment value]* According to the Standard settings submitted by the Technical Department[Adjustment standard value] Measuring instrument: [Minolta CA-210] Technical measuring instrument
Point 4 Level Reference value Adjustment spec Inspection specWBI40560
Point 6 928X=0.272 0.0010 0.0020
MG4G**** y=0.277MG4B****
Point 5 776X=0.272 0.0010 0.0020
MG4R**** y=0.277
Point 4 560X=0.272 0.0020 0.0040
Point 3 y=0.277WBI30308
Point 3 308X=0.272 0.0020 0.0040
MG3G**** y=0.277MG3B****
Point 2 224X=0.272 0.0030 0.0060
MG3R**** y=0.277
Point 1 184X=0.272 0.0035 0.0070y=0.277
Point 2WBI20224MG2G****MG2B****MG2R****
Remarks Setting conditions when performing inspectionAV MODE: [DYNAMIC] (Reset)Monochro: ONActive Backlight: OFFAging Time: Min. 60 minutes
Point 1WBI10184MG1G****MG1B****MG1R****
WritingMSET0003
-
LC-32/40/46/52LE700UN9.2. Adjusting procedure by use of [RS-232C]1. Get ready the PC with COM port (RS-232C) running on Windows 95/98/ME/2000/XP operating system, as well as the RS-232C cross cable.
2. Start the unit with the RS-232C cable connected.
3. Start the terminal software. (The freeware readily available on the Internet will do.)
4. Make the following settings.
5. If the settings are correct, the terminal software indicates ERR against pressing of the ENTER key.
6. After the settings are done correctly, it is possible to make an adjustment by typing in the command shown in the table below and pressing theENTER key on the keyboard.
7. Command entry is successful if the terminal software indicates OK when the ENTER is pressed. If ERR is shown, retry to enter the command.
8. Send the process mode switching command to switch from the RS232C operation mode to the process mode.
KRSW0001: ERR i
KKT10037: When O
9. Send each adjustme
10. Key writing
10.1. EDID writing (M
10.2. MAC address 1. Write the MAC key d
2. The data must be wr
Baud rate 9,600 bpsData LENGTH 8 bitParity bit NoneStop bit 1 bitFlow control None
Adjustmen1 HDMI EDID writin
(Main PWB)
2 Analog RGB EDI(Main PWB)5 15
s returned.
K is returned, the process mode becomes active. When ERR, start over from KRSW0001.
nt command.
ain PWB: QPWBXF282WJZZ)
writing (Main PWB: QPWBXF282WJZZ) (Except for LC-32LE700UN)ata into IC8453 mounted on the MAIN PWB via RS232C.
itten before making the inspection using the checker.
t point Adjustment conditions Adjustment procedureg Process mode
Model discrimination check1) Enter the process mode.2) Point the cursor to [HDMI EDID WRITE] and press the [ENT]
key.The writing is complete when [OK] is displayed.(If not written, HDMI does not function.)
CAUTION: Perform the data writing after setting the model discrimi-nation. The data based on the model discrimination information is recorded in EEPROM.
D writing Inspection modeFile version check
1) Write the EDID data for analog RGB into IC1809 mounted on the main PWB.TL1821 I2C clock, TL1823 I2C dataTL1824 5V, TL1822 GNDTL1848 Write protection (H: WP, L: write enable)
2) Perform the data writing before making inspection using the checker.
-
LC-32/40/46/52LE700UN11. Factory settingAfter completing the factory setting, pull out the AC cord to complete the setting.
CAUTION: Do not turn on the power after completing the factory setting. If the power is turned on, configure the factory setting again.
12. Writing the incWriting method
1. Pull out the AC cord
2. Copy the application
3. Hold down the powe
4. Release the power b
5. Update starts.
6. Pull out the AC cord
Model/inch file
40LE700.MDL
46LE700.MDL
52LE700.MDL
* 32 inch is not necess
NOTE: When replacing
Adjustment point Adjustment conditions Adjustment procedure1 Factory setting Complete the setting by
pulling out the AC cord..Point the cursor to [INDUSTRY INIT (+Cause)], set to ON using [+]/[-] of the [VOL] key, and press the [ENT] key.The version confirmation screen appears on the green screen. It is completed when [SUC-CESS] is displayed at the top.(If error occurs, [ERROR] is displayed on the red screen.)Turn off the AC power.The following items are initialized when configuring the factory setting.1) User setting values2) Channel data (broadcasting frequency, etc.)3) Password setting value4) Operating time5) Standby Cause6) Auto installation flag7) V-CHIP block setting value
U5 16
h and model name onto EEPROM
.
for writing inch/model name (HLNRMA01.USB) and model/inch file (40LE700.MDL) to the USB memory.
r button and insert the AC cord.
utton after 5 seconds.
.
ary.
the main PWB, make sure to perform the writing the inch and model name onto EEPROM
52LE700
PGRADE SUCCESS
The inch and model name are displayed.
-
LC-32/40/46/52LE700UN[2] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode There are the following two ways to get the public mode setup screen displayed.
In the adjustment process mode, turn on PUBLIC MODE. Also press the CH ( ) and VOL (+) keys on the set at once and turn on thepower.
1) Press the INPUT and VOL (+) keys on the set at once and turn on the power.
2) Get the password input screen displayed.
3) The 3-digit passw
The password [0
With any other p
2. How to exit PubThere are the following
Turn off PUBLIC MOD Turn off the power wit Select EXECUTE. (
... PUBLIC MODE s
... The settings will be
3. Public Mode Se With the factory settin
Procedure
The input starts with the leftmost digit.Use the numeric keys [1] thru [9] and [0] keys on the remote controller.The other keys are not acceptable.With a numeric-key input, "_" will change to "".The input position will move one digit to the right.With all the 3 digits entered, the password will be verified.5 17
ord is now verified.
] [2] [7] provides for the public mode screen. (This screen comes on with whatever adjustment process settings.)
asswords, the screen changes to the normal mode.
lic Modeways to quit the public mode setup screen.
E in the adjustment process mode. ( ) This way alone is not for quitting the setup screen, but for quitting the mode itself.h the POWER key. ( )
)
tays on in the adjustment process mode.
back to the factory ones.
tting Valuesgs made, the public mode settings get initialized. (The adjustment process remains intact.)
-
LC-32/40/46/52LE700UN4. Public Mode MenuThe guidance is not displayed on screen.
Setup procedure
To move the cursor up and down, use the cursor UP/DOWN key (remote controller) and CH ( )/( ) key (remote controller and set). To change the settings, use the cursor RIGHT/LEFT key (remote controller) and VOL (+)/() key (remote controller and set). To save new settings, keep the cursor at EXECUTE and use ENTER key (remote controller and set).
PUBLIC MODE
POWER ON FIXED [VARIABLE ]
MAXIMUM VOLUME [ 60 ]
VOLUME FIXED [VARIABLE ]
VOLUME FIXED LEVEL [ 20 ]
RC BUTTON [RESPOND ]
PANE
MENU
AV PO
ON SC
INPUT
INPUT
LOUD
RC_P
232C
PUBLI
RESE
EXEC5 18
L BUTTON [RESPOND ]
BUTTON [RESPOND ]
SITION FIXED [VARIABLE ]
REEN DISPLAY [YES ]
MODE START [NORMAL ]
MODE FIXED [VARIABLE ]
SPEAKER [ON ]
ATH_THROUGH [OFF ]
POWON [DISABLE ]
C MODE [OFF ]
T
UTE
-
LC-32/40/46/52LE700UN5. On Setting Items* EZ-SETUP discussed below indicates EZ-SETUP after the first power-on.
1) POWER ON FIXED
2) MAXIMUM VOLUME
3) VOLUME FIXED
4) VOLUME FIXED LE
5) RC BUTTON
Selection Selection between Variable and Fixed (loop provided)Default (Variable)Explanation In Fixed setting, the power-off by the power key of the unit is invalidated and the image is kept being received. The power can
be turned off by stopping the power supply from AC.Limit in Setting Refer to the Power-On Fixed sheet.Exception NoneRemarks In Variable setting, the power operation is in wait for 1 sec. and then turned off when the main power switch is off.
Selection Adjustment from 0 to 60 (no loop)Default 60Explanation Sound volume can not be adjusted higher than the preset value.Limit in Setting
ExceptionRemarks
pr
Selection SDefault VaExplanation
Limit in Setting im
Exception Remarks
so
Selection ADefault 20Explanation ThLimit in Setting NException NRemarks S
Selection SDefault RExplanation M
Limit in SettingException
Remarks5 19
VEL
When the sound volume is set lower than 59, only figures are displayed and the sound volume bar is not displayed.The maximum sound volume for ON-timer (Wake up timer) is limited also to the preset value.
When the sound volume is set higher than the MAX setting by the adjusting process, the sound volume control operation is ohibited for turn-up and the sound volume should be turned down to MAX in this state.
election between Variable, Fixed, ACON (AC CTRL) and AC/RCON (AC/RC CTRL) (loop provided)riable
FIXED: Fixed at the level adjusted for a fixed volume.AC CTRL: Start-up at the level specified for a fixed volume at ACON.AC/RC CTRL: Start-up at the level specified for a fixed volume at start.The sound volume for the ON-timer (Wake up timer) is fixed also without display of menu. Besides, the setting is made possible. (Basically, the menu is not displayed.)
The following keys become invalid: Sound volume Up/Down (VOL +/) [for both remote control and the unit] Mute (MUTE)In the item VOLUME of adjustment process, the sound volume can be set freely irrespective of this setting.As for sound volume fixing and sound volume MAX level, the sound volume fixing has priority.Once the sound volume has been changed by adjustment process, it should be set back to the sound volume preset by und volume fixing level when the adjustment process ends.
djustment from 1 to 60 (no loop)
e sound volume to be fixed by Volume fixed is determined.oneoneetting is valid only when Volume fixed is selected for fixed.
election between Respond, No Respond and Limited (loop provided)espondaking the remote controller settings.At the No Respond setting, the remote controller keys are disabled. Its power key (reception/standby key) is disabled too.At the Limited setting, some channel-related keys alone are operative. All the other remote controller keys (power, volume
/ , channel / , light control (brightness sensor), broadcast select) are inoperative.In No respond setting, all the keys (including the power key) are not accepted.
Adjustment process, inspection process and hotel only keys are valid irrespective of setting.All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
-
LC-32/40/46/52LE700UN6) PANEL BUTTON
7) MENU BUTTON
8) ON SCREEN DISPL
9) INPUT MODE STAR
Selection Selection between Respond and No respond (loop provided)Default RespondExplanation All the operations by keys (except the power key) of the unit can be invalidated.Limit in SettingException Adjustment process, inspection mode and hotel menu mode can be started irrespective of setting.
All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.Remarks
Selection Selection between Respond and No respond (loop provided)Default RespondExplanation In No respond setting, the menu operation by the menu key of the remote control and the menu key of the unit are invali-
dated.Limit in SettingException Adjustment process, inspection mode and hotel menu mode can be started irrespective of setting.
All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.Remarks
Selection SDefault YeExplanation
umO OsaO
Limit in Setting
Sso
Others chB
Exception
Remarks
Selection SDefault NExplanation In
(InAbout options
op
Limit in Setting ExceptionRemarks 5 20
AY
T
election between Yes, No (loop provided)s
At the No setting, the following items are not displayed on screen: register, setting, adjustment menu, channel call and vol-e bar.
n the wide-screen models, an input selection is immediately made because the menu is not displayed.At the Limited setting, some items cannot be displayed on screen.n the Japan-destined models, the channel call Message alone cannot be displayed. (This is because the channel call mes-ge may be confused with a message being sent from the hotel.)
n the North America-destined models, the OSD works the same as at the No setting.Keys falling under any of the following items become invalid.Appearance of screen changes and the sound changes.Personal functions which are hard to restore.
creen display, menu, OFF-timer, ON-timer, AV MODE, screen size switching, clock setting, treble emphasis, AUDIO ONLY, und changeover, LANGUAGE, CLOSED CAPTION
Simple input switching is generated. Those which are restored soon after leaving as they are and may be requested for ange by customer are not prohibited.
rightness sensor (BACKLIGHT) and PIC. FLIPSuch a caution which is displayed independently is displayed as it is.Non-responding signal cautionWhen CC has already been ON, CLOSED CAPTION is displayed.
election between Normal, Air ( ), INPUT 1/2/3, PC, HDMI 1/2/3/4/5, DVI (loop provided)ormal power-ON, the input source to be started or channel can be set. standard mode, the operation follows the last memory.)
All the input sources in the model are made selectable.In TV mode, the channel to be set follows the last memory and the content of the last memory is included in the notation by tions. Ex.) Air (2), Cable (98.1) etc.
The display of channel setting menu and the channel setting operation are prohibited.
In setting at Normal, the setting of Input mode fixed is changed to Variable and selection should be prohibited.
-
LC-32/40/46/52LE700UN10)INPUT MODE FIXED
11)RC_PATH_THROUGH
12)AV POSITION FIXED
13)LOUD SPEAKER (O
14)232C POWON
Selection Selection between Variable, Fixed, ACON (AC CTRL) and AC/RCON (AC/RC CTRL) (loop provided)Default (Variable)Explanation At the Fixed setting, the TV set gets started with the settings of Input mode start, and then any other channels and inputs
are not accepted. At the ACON (AC CTRL) setting, the TV set gets started with the settings of Input mode start under AC control. At the AC/RCON (AC/RC CTRL) setting, the TV set gets started with the settings of Input mode start under either control.
Limit in Setting With the execution of hotel mode, the input source is forced to change to that set by Input mode start and the channel switching and input switching are prohibited thereafter. ON-timer's (Wake-up timer) channel items are not displayed or the operation is prohibited. (Basically, they are not displayed.) The following keys are invalidated.CH / , direct tuning button, FLASHBACK, input
However, the keys (input switching and CH / keys) of the unit for menu operation remain valid.Exception NoneRemarks In the following case, setting is cancelled and mode is changed to Variable.
When the setting of Input mode start is set to Normal.
Selection SDefault OExplanation FuLimit in Setting NException NRemarks N
Selection SDefault VaExplanation In
Limit in Setting NException NRemarks
se au
Selection SDefault OExplanation If Limit in Setting NException NRemarks
Selection SDefault DExplanation InLimit in Setting NException NRemarks N5 21
N/OFF)
election between OFF, ON: TV RCE and ON: TV RCD (loop provided)FFnction to feed the remote controller-received signal to Pin 9 (open) on the RS232C.
oneoneone
election between Variable and Fixed (loop provided)riable
case of Fixed setting, Menu Picture and Audio setting can't be changed like Dynamic (Fixed).When AV Mode key is pressed, TV just displays current AV Mode (cannot be changed.).oneoneWhen receiving with AV Position key, OPC, Dolby key and other direct audio select keys, the current display stays on and no tting can be changed.
Even by initializing personal information, the hotel-mode settings are kept intact. In this way, the AV positions, video and dio adjustment settings are not initialized.
election between ON and OFF (loop provided)NOFF is selected, TV stops Speaker output even without Headphone connected.oneonePress the volume UP/DOWN key, and the mute icon appears for 4 seconds.The mute key and audio-related keys are displayed with caution.Usually, the headphones and monitor audio outputs can be adjustable.
election between Disable and Enable (loop provided)isable the standby mode, the power-on by the 232C command is enabled or disabled.oneoneone
-
LC-32/40/46/52LE700UN15)PUBLIC MODE (ON/OFF)
Selection Selection between ON and OFF (loop provided)Default OFFExplanation In case of ON, public mode settings are effected.Limit in Setting NoneException NoneRemarks The public-mode settings are operable only when this item is set at ON.5 22
-
LC-32/40/46/52LE700UNLC32LE700UN Service Manual CHAPTER 6. TROUBLESHOOTING TABLE
[1] TR