182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g.,...
-
Upload
duonghuong -
Category
Documents
-
view
219 -
download
1
Transcript of 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g.,...
![Page 1: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/1.jpg)
182.694 Microcontroller VU
Martin PernerSS 2017
Featuring Today:Assembler Programming
![Page 2: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/2.jpg)
Weekly Training Objective
Already done1.2 Board test †
2.1.1 Assembler demo program †2.1.2 Makefile †2.2.1 Logical operations ∗
This week2.2.2 Input with floating pins ∗2.2.4 Monoflop buttons2.2.5 Digital I/O2.4.1 precompiled LCD ∗
Until Exam2.2.3 LED Rain ∗2.2.8 LED curtain ∗2.4.2 Calling conventions I2.4.3 Calling conventions II
March 13, 2017 2
![Page 3: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/3.jpg)
Assembler Programming
Assembler is always very “device specific”→ AVR-Assembler
Start with basic AVR Assembler
Followed by “advanced” examples
March 13, 2017 3
![Page 4: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/4.jpg)
I’m learning Assembler. It feels like this:
Figure: https://imgur.com/a/XM3KN
March 13, 2017 4
![Page 5: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/5.jpg)
I’m learning Assembler. It feels like this:
Figure: https://imgur.com/a/XM3KN
March 13, 2017 5
![Page 6: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/6.jpg)
Why Assembler?
see how all programs you write “really” end up
to understand the CPU architecture better
to understand where speed improvements may be possible
to realize there is no big secret behind it
March 13, 2017 6
![Page 7: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/7.jpg)
“Features” of Assembler
Assembler is basically a 1–1 mapping to machine code
Assembly language is human readable
No high-level language constructs, e.g., if or while
No nested expressions.e.g., you cannot write add (mult 3,2), 1
March 13, 2017 7
![Page 8: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/8.jpg)
Assembler Basics
Bit operations
Used for Digital I/O (set or clear port pins)
Example: PA0 drives high-active LED. Turn that LED on.
sbi DDRA, DDA0sbi PORTA, PA0
;better?sbi PORTA, PA0sbi DDRA, DDA0
switching a MC-Pin from * to Output:Mostly better to first change PORT register and then the DDR.Avoids glitches!
March 13, 2017 8
![Page 9: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/9.jpg)
Assembler Basics
Bit operations
Used for Digital I/O (set or clear port pins)
Example: PA0 drives high-active LED. Turn that LED on.
sbi DDRA, DDA0sbi PORTA, PA0
;better?sbi PORTA, PA0sbi DDRA, DDA0
switching a MC-Pin from * to Output:Mostly better to first change PORT register and then the DDR.Avoids glitches!
March 13, 2017 8
![Page 10: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/10.jpg)
Assembler Basics
Bit operations
Used for Digital I/O (set or clear port pins)
Example: PA0 drives high-active LED. Turn that LED on.
sbi DDRA, DDA0sbi PORTA, PA0
;better?sbi PORTA, PA0sbi DDRA, DDA0
switching a MC-Pin from * to Output:Mostly better to first change PORT register and then the DDR.Avoids glitches!
March 13, 2017 8
![Page 11: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/11.jpg)
Assembler Basics
Example
PA7 connected with button against ground
Objective: Read button value
sbi PORTA, PA7cbi DDRA, DDA7in r16, PORTA
;much better!cbi DDRA, DDA7sbi PORTA, PA7in r16, PINA
Common mistake!
reading PINx gives real input valuereading PORTx gives pull-up/output status
switching a MC-Pin from * to Input:Mostly better first to change DDR register. Avoids glitches!
March 13, 2017 9
![Page 12: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/12.jpg)
Assembler Basics
Example
PA7 connected with button against ground
Objective: Read button value
sbi PORTA, PA7cbi DDRA, DDA7in r16, PORTA
;much better!cbi DDRA, DDA7sbi PORTA, PA7in r16, PINA
Common mistake!
reading PINx gives real input valuereading PORTx gives pull-up/output status
switching a MC-Pin from * to Input:Mostly better first to change DDR register. Avoids glitches!
March 13, 2017 9
![Page 13: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/13.jpg)
Assembler Basics
Example
PA7 connected with button against ground
Objective: Read button value
sbi PORTA, PA7cbi DDRA, DDA7in r16, PINA
;much better!cbi DDRA, DDA7sbi PORTA, PA7in r16, PINA
Common mistake!
reading PINx gives real input valuereading PORTx gives pull-up/output status
switching a MC-Pin from * to Input:Mostly better first to change DDR register. Avoids glitches!
March 13, 2017 9
![Page 14: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/14.jpg)
Assembler Basics
Example
PA7 connected with button against ground
Objective: Read button value
sbi PORTA, PA7cbi DDRA, DDA7in r16, PINA
;much better!cbi DDRA, DDA7sbi PORTA, PA7in r16, PINA
Common mistake!
reading PINx gives real input valuereading PORTx gives pull-up/output status
switching a MC-Pin from * to Input:Mostly better first to change DDR register. Avoids glitches!
March 13, 2017 9
![Page 15: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/15.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off.
cbi PORTA, PA0sbi PORTA, PA1sbi PORTA, PA2cbi PORTA, PA3sbi DDRA, DDA0sbi DDRA, DDA1sbi DDRA, DDA2sbi DDRA, DDA3
Works, but we can do better!
March 13, 2017 10
![Page 16: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/16.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off.
ldi temp, 0x06 ;0000 0110out PORTA, templdi temp, 0x0F ;0000 1111out DDRA, temp
Works, but we are overwriting unused bits!
Consider the previous example: PA7 is configured as an input with pull-up
Now it is an input without pull-up!
Not really readable (which bits are set if PORTA = 0xCA?)
March 13, 2017 11
![Page 17: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/17.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off.
ldi temp, 0x06 ;0000 0110out PORTA, templdi temp, 0x0F ;0000 1111out DDRA, temp
Works, but we are overwriting unused bits!
Consider the previous example: PA7 is configured as an input with pull-up
Now it is an input without pull-up!
Not really readable (which bits are set if PORTA = 0xCA?)
March 13, 2017 11
![Page 18: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/18.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off.
ldi temp, 0x06 ;0000 0110out PORTA, templdi temp, 0x0F ;0000 1111out DDRA, temp
Works, but we are overwriting unused bits! → unused?
Consider the previous example: PA7 is configured as an input with pull-up
Now it is an input without pull-up!
Not really readable (which bits are set if PORTA = 0xCA?)
March 13, 2017 11
![Page 19: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/19.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off.
ldi temp, 0x06 ;0000 0110out PORTA, templdi temp, 0x0F ;0000 1111out DDRA, temp
Works, but we are overwriting unused bits! → unused?
Consider the previous example: PA7 is configured as an input with pull-up
Now it is an input without pull-up!
Not really readable (which bits are set if PORTA = 0xCA?)
March 13, 2017 11
![Page 20: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/20.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off without changing other PINs.
in temp, PORTAori temp, (1<<PA1)|(1<<PA2)out PORTA, temp
in temp, DDRAori temp, (1<<DDA0)|(1<<DDA1)|(1<<DDA2)|(1<<DDA3)out DDRA, temp
Instead of (1<<PA1) one can use BV(PA1).
March 13, 2017 12
![Page 21: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/21.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off without changing other PINs.
in temp, PORTAori temp, (1<<PA1)|(1<<PA2)out PORTA, temp
in temp, DDRAori temp, (1<<DDA0)|(1<<DDA1)|(1<<DDA2)|(1<<DDA3)out DDRA, temp
Nearly correct!
March 13, 2017 12
![Page 22: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/22.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off without changing other PINs.
in temp, PORTAori temp, (1<<PA1)|(1<<PA2)andi temp, (0<<PA0)&(0<<PA3)out PORTA, temp
in temp, DDRAori temp, (1<<DDA0)|(1<<DDA1)|(1<<DDA2)|(1<<DDA3)out DDRA, temp
Not correct!
March 13, 2017 12
![Page 23: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/23.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off without changing other PINs.
in temp, PORTAori temp, (1<<PA1)|(1<<PA2)andi temp, (0<<PA0)&(0<<PA3)out PORTA, temp
in temp, DDRAori temp, (1<<DDA0)|(1<<DDA1)|(1<<DDA2)|(1<<DDA3)out DDRA, temp
Not correct!
March 13, 2017 12
![Page 24: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/24.jpg)
Assembler Basics
Another example
PA3:0 are connected to LED3:0.Turn on LED1 and LED2 and turn the other ones off without changing other PINs.
in temp, PORTAori temp, (1<<PA1)|(1<<PA2)andi temp, ˜((1<<PA0)|(1<<PA3))out PORTA, temp
in temp, DDRAori temp, (1<<DDA0)|(1<<DDA1)|(1<<DDA2)|(1<<DDA3)out DDRA, temp
Correct!
March 13, 2017 12
![Page 25: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/25.jpg)
Assembler Basics
Procedure is called RMW
Read
Modify
Write
Should always be used!
Interrupts, Timer, ADC, . . .Assembler, C, . . .
Not explicitly checked in the first exam, but . . .
. . . in the second and the make-up exam we will check that no bits are unnecessarilychanged!
March 13, 2017 13
![Page 26: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/26.jpg)
Assembler Basics
Procedure is called RMW
Read
Modify
Write
Should always be used!
Interrupts, Timer, ADC, . . .Assembler, C, . . .
Not explicitly checked in the first exam, but . . .
. . . in the second and the make-up exam we will check that no bits are unnecessarilychanged!
March 13, 2017 13
![Page 27: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/27.jpg)
Assembler Basics
Procedure is called RMW
Read
Modify
Write
Should always be used!
Interrupts, Timer, ADC, . . .Assembler, C, . . .
Not explicitly checked in the first exam, but . . .
. . . in the second and the make-up exam we will check that no bits are unnecessarilychanged!
March 13, 2017 13
![Page 28: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/28.jpg)
Assembler Basics
Procedure is called RMW
Read
Modify
Write
Should always be used!
Interrupts, Timer, ADC, . . .Assembler, C, . . .
Not explicitly checked in the first exam, but . . .
. . . in the second and the make-up exam we will check that no bits are unnecessarilychanged!
March 13, 2017 13
![Page 29: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/29.jpg)
Pull-Ups
Why do we even use them?
Why don’t we just connect the push-button to VCC instead of ground, and sense a pressedbutton as high instead of low?
Electrical Characterisitics
The ATmega1280 has a absolute maximum rating of 40 mA per I/O pin. Thus, 0.2 W is themaximum allowed load on a pin!There is also an overall maximum (200 mA) for all pins!
Drive large loads
If you have to drive loads above the limit, use the port to enable a transistor to drive the load.
Internal Pull-Ups are weak
This is by design, to prevent the current from exceeding the maximum rating.
March 13, 2017 14
![Page 30: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/30.jpg)
Pull-Ups
Why do we even use them?
Why don’t we just connect the push-button to VCC instead of ground, and sense a pressedbutton as high instead of low?
Electrical Characterisitics
The ATmega1280 has a absolute maximum rating of 40 mA per I/O pin. Thus, 0.2 W is themaximum allowed load on a pin!There is also an overall maximum (200 mA) for all pins!
Drive large loads
If you have to drive loads above the limit, use the port to enable a transistor to drive the load.
Internal Pull-Ups are weak
This is by design, to prevent the current from exceeding the maximum rating.
March 13, 2017 14
![Page 31: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/31.jpg)
Pull-Ups
Why do we even use them?
Why don’t we just connect the push-button to VCC instead of ground, and sense a pressedbutton as high instead of low?
Electrical Characterisitics
The ATmega1280 has a absolute maximum rating of 40 mA per I/O pin. Thus, 0.2 W is themaximum allowed load on a pin!There is also an overall maximum (200 mA) for all pins!
Drive large loads
If you have to drive loads above the limit, use the port to enable a transistor to drive the load.
Internal Pull-Ups are weak
This is by design, to prevent the current from exceeding the maximum rating.
March 13, 2017 14
![Page 32: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/32.jpg)
Pull-Ups
Why do we even use them?
Why don’t we just connect the push-button to VCC instead of ground, and sense a pressedbutton as high instead of low?
Electrical Characterisitics
The ATmega1280 has a absolute maximum rating of 40 mA per I/O pin. Thus, 0.2 W is themaximum allowed load on a pin!There is also an overall maximum (200 mA) for all pins!
Drive large loads
If you have to drive loads above the limit, use the port to enable a transistor to drive the load.
Internal Pull-Ups are weak
This is by design, to prevent the current from exceeding the maximum rating.
March 13, 2017 14
![Page 33: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/33.jpg)
Analogy: Single Line and Ground
10
10
Fixing the levers to a common plate.
⇒ large current flowing and no detection of change!
March 13, 2017 15
![Page 34: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/34.jpg)
Analogy: Single Line and Ground
10
10
Fixing the levers to a common plate.⇒ large current flowing and no detection of change!
March 13, 2017 15
![Page 35: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/35.jpg)
Analogy: Single Line, Ground and Pull-Up
X0
X0
A weak spring keeps the bar in the high state (=weak/recessive state).
March 13, 2017 16
![Page 36: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/36.jpg)
Analogy: Single Line, Ground and Pull-Up
X0
X0
A weak spring keeps the bar in the high state (=weak/recessive state).
March 13, 2017 16
![Page 37: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/37.jpg)
Internal Structure of a Port
Figure: ATmega 1280, Figure 13-2 General Digital I/O
March 13, 2017 17
![Page 38: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/38.jpg)
Questions
Connect two output pins
Both are configured as output
one is set to high
the other to low
Short circuit!
Connect two inputs pins
Both are configured as input
one has the internal pull-up enabled
the other one has not.
Both read high.
March 13, 2017 18
![Page 39: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/39.jpg)
Questions
Connect two output pins
Both are configured as output
one is set to high
the other to low
Short circuit!
Connect two inputs pins
Both are configured as input
one has the internal pull-up enabled
the other one has not.
Both read high.
March 13, 2017 18
![Page 40: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/40.jpg)
Questions
Connect two output pins
Both are configured as output
one is set to high
the other to low
Short circuit!
Connect two inputs pins
Both are configured as input
one has the internal pull-up enabled
the other one has not.
Both read high.
March 13, 2017 18
![Page 41: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/41.jpg)
Questions
Connect two output pins
Both are configured as output
one is set to high
the other to low
Short circuit!
Connect two inputs pins
Both are configured as input
one has the internal pull-up enabled
the other one has not.
Both read high.
March 13, 2017 18
![Page 42: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/42.jpg)
Questions
Connect two inputs pins
Both are configured as input
one has an external pull-up enabled
the other one has not.
Both read high.
Connect two inputs pins
Both are configured as input
one has an external pull-up enabled
the other one an external pull-down enabled.
Both read their value? (Short circuit!)
March 13, 2017 19
![Page 43: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/43.jpg)
Questions
Connect two inputs pins
Both are configured as input
one has an external pull-up enabled
the other one has not.
Both read high.
Connect two inputs pins
Both are configured as input
one has an external pull-up enabled
the other one an external pull-down enabled.
Both read their value? (Short circuit!)
March 13, 2017 19
![Page 44: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/44.jpg)
Questions
Connect two inputs pins
Both are configured as input
one has an external pull-up enabled
the other one has not.
Both read high.
Connect two inputs pins
Both are configured as input
one has an external pull-up enabled
the other one an external pull-down enabled.
Both read their value? (Short circuit!)
March 13, 2017 19
![Page 45: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/45.jpg)
Questions
Connect two inputs pins
Both are configured as input
one has an external pull-up enabled
the other one has not.
Both read high.
Connect two inputs pins
Both are configured as input
one has an external pull-up enabled
the other one an external pull-down enabled.
Both read their value? (Short circuit!)
March 13, 2017 19
![Page 46: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/46.jpg)
Attention!
Parallel resistors reduce the cumulative resistance!
Thus connecting multiple pull-up/down resistors to one pin, e.g., incorrect usage of a matrixkeypad, may lead to a violation of the maximum current! Check the lecture notes Sec. 5.2 onhow this should be done.
Warning
There will be point deductions in the applications if you require a setup which causes shorts /conflicting drivers!Draw a schematic, for yourself, to check if there are problems!
March 13, 2017 20
![Page 47: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/47.jpg)
SBI vs. SBR
SBI: Set Bit in I/O Register (already heard)
e.g., sbi PORTA, PA7 ;sets bit 7 in PORTA register
only works in the first 32 I/O Registers (most timer registers are above)
SBR: Set Bits in Register
works on (upper 16) General Purpose Registers (r16-r31)
second argument is a bitmask: 0x07 → 0b0000 0111
takes over all “ones” in the bitmask to the target register
other option to achieve this?
March 13, 2017 21
![Page 48: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/48.jpg)
SBI vs. SBR
SBI: Set Bit in I/O Register (already heard)
e.g., sbi PORTA, PA7 ;sets bit 7 in PORTA register
only works in the first 32 I/O Registers (most timer registers are above)
SBR: Set Bits in Register
works on (upper 16) General Purpose Registers (r16-r31)
e.g., sbr r16, 7 ;set bit 7 in register 16
second argument is a bitmask: 0x07 → 0b0000 0111
takes over all “ones” in the bitmask to the target register
other option to achieve this?
March 13, 2017 21
![Page 49: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/49.jpg)
SBI vs. SBR
SBI: Set Bit in I/O Register (already heard)
e.g., sbi PORTA, PA7 ;sets bit 7 in PORTA register
only works in the first 32 I/O Registers (most timer registers are above)
SBR: Set Bits in Register
works on (upper 16) General Purpose Registers (r16-r31)
e.g., sbr r16, 7 ;set bit 7 in register 16
second argument is a bitmask: 0x07 → 0b0000 0111
takes over all “ones” in the bitmask to the target register
other option to achieve this?
March 13, 2017 21
![Page 50: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/50.jpg)
SBI vs. SBR
SBI: Set Bit in I/O Register (already heard)
e.g., sbi PORTA, PA7 ;sets bit 7 in PORTA register
only works in the first 32 I/O Registers (most timer registers are above)
SBR: Set Bits in Register
works on (upper 16) General Purpose Registers (r16-r31)
e.g., sbr r16, 7 ;set bits 2:0 in register 16
second argument is a bitmask: 0x07 → 0b0000 0111
takes over all “ones” in the bitmask to the target register
other option to achieve this?
March 13, 2017 21
![Page 51: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/51.jpg)
SBI vs. SBR
What about ori?
ori r16, 7does it do the same as sbr r16, 7?
solution: compare the opcodes (AVR Instruction Set):sbr: 0110 KKKK dddd KKKKori: 0110 KKKK dddd KKKK
March 13, 2017 22
![Page 52: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/52.jpg)
SBI vs. SBR
What about ori?
ori r16, 7does it do the same as sbr r16, 7?
solution: compare the opcodes (AVR Instruction Set):sbr: 0110 KKKK dddd KKKKori: 0110 KKKK dddd KKKK
March 13, 2017 22
![Page 53: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/53.jpg)
Other Assembler Stuff
CBR: Clear Bits in Registers
works like sbr but clears all bits where the bitmasks is 1cbr r16, 0x05 → andi r16, (0xFF − 0x05)
LSL: Logical Shift Left
shifts all bits in register one place to the left. Bit 0 is cleared. Implementation in the AVR core:add rd, rd (add without carry)
March 13, 2017 23
![Page 54: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/54.jpg)
Other Assembler Stuff
Many of these ‘tricks’ can be found in the Instruction Set
ser (set all bits in register) is implemented as ldi with “hardcoded” value 0xFF.
clr Rd (clear register) is implemented as eor Rd, Rd
ld Rd, Z (indirect load from data space) is implemented as ldd Rd, Z+q (indirect loadwith displacement) with q= 0
March 13, 2017 24
![Page 55: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/55.jpg)
Advanced Assembler Programming
“More than 8-bit” – Operations
A = r17:16, B = r19:18
16-bit addition (A ← A+B)add r16, r18 ;r16 + r18adc r17, r19 ;r17 + r19 + C
16-bit subtraction (A ← A-B)sub r16, r18 ;r16 - r18sbc r17, r19 ;r17 - r19 - C
8-bit multiplication → 16-bit resultmul r16, r17 ; r1:r0 ← r16 × r17
Accessing 16-bit registers (be aware!)
March 13, 2017 25
![Page 56: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/56.jpg)
Examples – if
Given
if(r17==2)r18 = 0;
elser18 = 1;
With r17 and r18 being CPU registers.
March 13, 2017 26
![Page 57: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/57.jpg)
Examples – if
Solution
cpi r17, 2 ; compare r17 with 2brne else ; if (!zero_flag) => elseldi r18, 0 ; r18 = 0rjmp end ; => end
else:ldi r18, 1 ; r18 = 1
end:
March 13, 2017 27
![Page 58: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/58.jpg)
Examples – while
Given
while (r17 < 20)r17++;
With r17 being a CPU register.
March 13, 2017 28
![Page 59: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/59.jpg)
Examples – while
Solution
while:cpi r17, 20 ; r17 - 20brge end ; if (!negative_flag) => end;addi r17, 1 ; r17 = r17 + 1jmp while ; => while
end:
March 13, 2017 29
![Page 60: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/60.jpg)
Stack
Stack
“Part” of the SRAM
Stores:
Temporary data (to backup registers used in ISRs)Local variables (mainly C programming)Return addresses of
Subroutine callsInterrupt Service Routines
Grows Top-Down (starts at highest SRAM address)
March 13, 2017 30
![Page 61: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/61.jpg)
Stack
Stack Pointer
“Pointer” to the first empty stack location (AVR)
Has to be initialized to the end of RAM
The ATmega1280 does this automaticallyBut it is good practice to do it; imagine you decide to implement a soft-reset feature(RAMEND is defined in .inc)
Be very careful when changing the Stack by hand!
There must NEVER be important data below the Stack Pointer (Interrupts)
March 13, 2017 31
![Page 62: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/62.jpg)
Assembler Functions with Parameters
How to pass Parameters?
3 different possibilities to hand parameters to functions
Depending on the number of parameter, some may not work
March 13, 2017 32
![Page 63: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/63.jpg)
Assembler Functions with Parameters
1. via Register
fast, easy, only 32 registers available
ldi r16, 'a'call toupper ;r16 <- toupper(r16)out PORTA, r16
March 13, 2017 33
![Page 64: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/64.jpg)
Assembler Functions with Parameters
2. via SRAM (heap)
ldi r16, 'a'ldi XL, 0x2?ldi XH, 0x1?st X, r16call toupper ;toupper(*X)ldi XL, 0x2?ldi XH, 0x1?ld r16, Xout PORTA, r16
March 13, 2017 34
![Page 65: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/65.jpg)
Assembler Functions with Parameters
3. via Stack
allows for variable number of parametersE.g., printf, is such a variadic function
push parameters on stack before calling the function
ldi r16, 'a'push r16call toupper ;r16 <- toupper('a')out PORTA, r16pop r16 ; clean stack
’a’
PC ret
PC ret add
ress
SP
after call
March 13, 2017 35
![Page 66: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/66.jpg)
Assembler Functions with Parameters
3. via Stack
what if we want something like:uint8 t myXOR(uint8 t x, uint8 t y)or uint16 t mySquare(uint8 t x)
param1
param2
param3
PC ret
PC ret add
ress
SP
after call
March 13, 2017 36
![Page 67: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/67.jpg)
Assembler Functions with Parameters
3. via Stack
what if we want something like:uint8 t myXOR(uint8 t x, uint8 t y)or uint16 t mySquare(uint8 t x)
param1 ?
param2 ?
param3 ?
add
ress
SP
after call
March 13, 2017 36
![Page 68: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/68.jpg)
Assembler Functions with Parameters
3. via Stack
Stack needs to be cleaned!Be very very careful!
caller-save vs. callee-save registers
caller-save: have to be saved/restored by caller (calleecan write on them without restore)callee-save: have to be saved/restored by the calleecallee-save is the more challenging task
It is good to have both→ calling conventions
See Exercise 2.4.3
What about interrupts?
param1
param2
param3
PC ret
PC ret
reg save1
reg save2
add
ress
SP
after call
March 13, 2017 37
![Page 69: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/69.jpg)
AVR Interrupt Handling
Interrupts
Events on Microcontroller
Different sources (Timer, ADC, Reset, . . . )
“Interrupts” the program execution
cannot be “predicted”
What happens when an Interrupt occurs?
Finishing the current instruction (if multi cycle)
Program Counter pushed on the stack / Interrupts are disabled
Instruction at corresponding Interrupt Vector is executed (normally a jump to InterruptService Routine)
March 13, 2017 38
![Page 70: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/70.jpg)
Interrupts
There are no “parameters” to Interrupts
Save all registers changed in the ISR on the stack — push
and restore them — pop — in reversed order
Do not forget to save the SREG!
ldi r16, 0x20cpi r16, 0x20breq is equaljmp is notequal
myisr:push r16in r16, PORTAinc r16out PORTA, r16pop r16reti
Return from ISR with reti
March 13, 2017 39
![Page 71: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/71.jpg)
Interrupts
There are no “parameters” to Interrupts
Save all registers changed in the ISR on the stack — push
and restore them — pop — in reversed order
Do not forget to save the SREG!
ldi r16, 0x20cpi r16, 0x20Interrupt → myisrbreq is equaljmp is notequal
myisr:push r16in r16, PORTAinc r16out PORTA, r16pop r16reti
Return from ISR with reti
March 13, 2017 39
![Page 72: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/72.jpg)
Interrupt Vector Table
“Normally” at the beginning of Program Memory
Reset Vector 0x000
INT0 Vector 0x002
INT1 Vector 0x004
. . .
jmp int1 isr
jmp int0 isr
jmp main
add
ress
0x000
0x001
0x002
0x003
0x004
0x005
Warning:
Program memory of the ATmega MCU is a 16-bit wide memory (addressed by word)
ISR Vector Addresses are word addresses
.org command uses byte addressing → multiply addresses by 2
March 13, 2017 40
![Page 73: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/73.jpg)
Interact with the environment
Polling vs. Interrupts
Timing more predictable.
Prevention of missing an event
Enter sleep mode ⇒ conserve energy
March 13, 2017 41
![Page 74: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/74.jpg)
Why polling is a bad idea
Small example application
Increment PORTA every 50 kHz
Every 256th increment perform some very sophisticated computation (SC), e.g., busy loopfor 40 µs
March 13, 2017 42
![Page 75: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/75.jpg)
Taking the easy road → let’s count up and it will work!
With polling
In an infinity loop increment a variable
on compare-match perform the action (increment PORTA).
Will it work? Simple answer: NO!
Why not?
The timing may work, but
high energy consumption
integration of additional functionality
how can a non-constant running time of the SC be handled?
March 13, 2017 43
![Page 76: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/76.jpg)
Taking the easy road → let’s count up and it will work!
With polling
In an infinity loop increment a variable
on compare-match perform the action (increment PORTA).
Will it work? Simple answer: NO!
Why not?
The timing may work, but
high energy consumption
integration of additional functionality
how can a non-constant running time of the SC be handled?
March 13, 2017 43
![Page 77: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/77.jpg)
Taking the easy road → let’s count up and it will work!
With polling
In an infinity loop increment a variable
on compare-match perform the action (increment PORTA).
Will it work? Simple answer: NO!
Why not?
The timing may work, but
high energy consumption
integration of additional functionality
how can a non-constant running time of the SC be handled?
March 13, 2017 43
![Page 78: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/78.jpg)
Using a timer; but without interrupt
Which timer value?
We use the Overflow interrupt
thus we need an offset to TCNT0’s maximum value (0xFF).
We decided to use a prescaler value of 8
16 MHz
8= 2 MHz
2 MHz
50 kHz= 40
255− 40 + 1 = 216 = 0xD8
March 13, 2017 44
![Page 79: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/79.jpg)
Using a timer; but without interrupt
. equ temp , 0x10
. equ c l r t , 0 x11
. s e c t i o n . t e x t
. g l o b a l main
. org 0x0000rjmp main
main :; i n i t i a l i z e s t a c k p o i n t e rl d i temp , l o 8 (RAMEND)out SPL , templ d i temp , h i 8 (RAMEND)out SPH , temp
; s e tup PORTAl d i temp , 0xFFout DDRA, tempout PORTA, temp
; c o n f i g u r e Timer0l d i temp , 0x00out TCCR0A, templ d i temp , 0xD8out TCNT0, templ d i c l r t , (1<<TOIE0 ); s t a r t c l o c kl d i temp , (1<<CS01 )out TCCR0B, temp
i n f i n i t e l o o p :; check i f t ime r has ove r r uni n temp , TIFR0and i temp , (1<<TOIE0 )breq no ov occu r ed
ov occu r ed :; r e s e t i n t e r r u p t f l a gout TIFR0 , c l r t; r e s e t Timerl d i temp , 0xD8out TCNT0, temp; i n c r ement po r ti n temp , PORTAinc tempout PORTA, tempbrne no o v e r f l ow
; SCo v e r f l ow :
l d i r18 , 255l o o p e r s :
dec r19brne l o o p e r s
n o o v e r f l ow :no ov occu r ed :
rjmp i n f i n i t e l o o p
March 13, 2017 45
![Page 80: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/80.jpg)
Using a timer; but without interrupt
Observation
Unstable frequency.This is due to the fact that TCNT is constantly incrementing when the timer is running, andwe are changing it at some point. This leads to either the value we wanted, or a ’few’increments more.
March 13, 2017 46
![Page 81: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/81.jpg)
Using a timer with Output-Compare-Match, still no interrupt
Which timer value?
We use the Output-Compare Match.
Again, we decided to use a prescaler value of 8
We use the formula on page 214 of the ATmega1280 manual.
Note: the frequency of this formula is for the signal “generated” by the interrupt. Thuswe double the frequency to get the interrupt frequency!
fOC0A =fOCR0A
2=
fclk2 ·N · (1 +OCR0A)
50 kHz
2=
16 MHz
16(1 +OCR0A)
OCR0A =16 MHz
16 · 25 kHz− 1 = 39 = 0x27
March 13, 2017 47
![Page 82: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/82.jpg)
Using a timer with Output-Compare-Match, still no interrupt
. equ temp , 0x10
. equ c l r t , 0 x11
. s e c t i o n . t e x t
. g l o b a l main
. org 0x0000rjmp main
main :; i n i t i a l i z e s t a c k p o i n t e rl d i temp , l o 8 (RAMEND)out SPL , templ d i temp , h i 8 (RAMEND)out SPH , temp
; s e tup PORTAl d i temp , 0xFFout DDRA, tempout PORTA, temp
; c o n f i g u r e Timer0l d i temp , (1<<WGM01)out TCCR0A, templ d i temp , 0x27out OCR0A, templ d i temp , 0x00out TCNT0, templ d i c l r t , (1<<OCF0A)
; s t a r t c l o c kl d i temp , (1<<CS01 )out TCCR0B, temp
i n f i n i t e l o o p :; check i f OC−I n t e r r u p t has occu redi n temp , TIFR0and i temp , (1<<OCF0A)breq no ov occu r ed
ov occu r ed :out TIFR0 , c l r ti n temp , PORTAinc tempout PORTA, tempbrne no o v e r f l ow
; SCo v e r f l ow :
l d i r18 , 255l o o p e r s :
dec r19brne l o o p e r s
n o o v e r f l ow :no ov occu r ed :
rjmp i n f i n i t e l o o p
March 13, 2017 48
![Page 83: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/83.jpg)
Using a timer with Output-Compare-Match, still no interrupt
Observation
Frequency more stable.Incorrect period on overflow/SC!
March 13, 2017 49
![Page 84: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/84.jpg)
Using a timer with Output-Compare-Match Interrupt
. equ temp , 0x10
. s e c t i o n . t e x t
. g l o b a l main
. org 0x0000rjmp main
. org OC0Aaddr∗2rjmp ov occu r ed
main :; i n i t i a l i z e s t a c k p o i n t e rl d i temp , l o 8 (RAMEND)out SPL , templ d i temp , h i 8 (RAMEND)out SPH , temp
; s e tup PORTAl d i temp , 0xFFout DDRA, tempout PORTA, temp
; c o n f i g u r e t ime rl d i temp , (1<<WGM01)out TCCR0A, templ d i temp , 0x27out OCR0A, templ d i temp , 0x00
out TCNT0, templ d i temp , (1<<OCIE0A)s t s TIMSK0 , temp; s t a r t c l o c kl d i temp , (1<<CS01 )out TCCR0B, temp
s e ii n f i n i t e l o o p :
rjmp i n f i n i t e l o o p
ov occu r ed :i n temp , PORTAinc tempout PORTA, tempbrne no o v e r f l ow
; SCo v e r f l ow :
l d i r18 , 255l o o p e r s :
dec r19brne l o o p e r s
n o o v e r f l ow :r e t i
March 13, 2017 50
![Page 85: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/85.jpg)
Using a timer with Output-Compare-Match Interrupt
Observation
Frequency stable.Still incorrect period on overflow/SC!
March 13, 2017 51
![Page 86: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/86.jpg)
Timer with OC-Match Interrupt, non-blocking ISR
. equ temp , 0x10
. s e c t i o n . t e x t
. g l o b a l main
. org 0x0000rjmp main
. org OC0Aaddr∗2rjmp ov occu r ed
main :; i n i t i a l i z e s t a c k p o i n t e rl d i temp , l o 8 (RAMEND)out SPL , templ d i temp , h i 8 (RAMEND)out SPH , temp
; s e tup PORTAl d i temp , 0xFFout DDRA, tempout PORTA, temp
; c o n f i g u r e t ime rl d i temp , (1<<WGM01)out TCCR0A, templ d i temp , 0x27out OCR0A, templ d i temp , 0x00
out TCNT0, templ d i temp , (1<<OCIE0A)s t s TIMSK0 , temp; s t a r t c l o c kl d i temp , (1<<CS01 )out TCCR0B, temp
s e ii n f i n i t e l o o p :
rjmp i n f i n i t e l o o p
ov occu r ed :i n temp , PORTAinc tempout PORTA, tempbrne no o v e r f l ows e i
; SCo v e r f l ow :
l d i r18 , 255l o o p e r s :
dec r19brne l o o p e r s
n o o v e r f l ow :r e t i
March 13, 2017 52
![Page 87: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/87.jpg)
Timer with OC-Interrupt, non-blocking ISR
Observation
Behaviour as specified.Do we need the infinity loop?
March 13, 2017 53
![Page 88: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/88.jpg)
Timer with OC-Interrupt, non-blocking ISR, and sleep mode
. s e c t i o n . t e x t
. g l o b a l main
. org 0x0000rjmp main
. org OC0Aaddr∗2rjmp ov occu r ed
main :; i n i t i a l i z e s t a c k p o i n t e rl d i temp , l o 8 (RAMEND)out SPL , templ d i temp , h i 8 (RAMEND)out SPH , temp; s e tup PORTAl d i temp , 0xFFout DDRA, tempout PORTA, temp; c o n f i g u r e t ime rl d i temp , (1<<WGM01)out TCCR0A, templ d i temp , 0x27out OCR0A, templ d i temp , 0x00out TCNT0, templ d i temp , (1<<OCIE0A)s t s TIMSK0 , temp; s t a r t c l o c kl d i temp , (1<<CS01 )
out TCCR0B, temp
s e ii n f i n i t e l o o p :
; goto s l e e pc l il d i temp , (1<<SE)out SMCR, temps e is l e e prjmp i n f i n i t e l o o p
ov occu r ed :i n temp , PORTAinc tempout PORTA, tempbrne no o v e r f l ows e i
; SCo v e r f l ow :
l d i r18 , 255l o o p e r s :
dec r19brne l o o p e r s
n o o v e r f l ow :r e t i
March 13, 2017 54
![Page 89: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/89.jpg)
Timer with OC-Interrupt, non-blocking ISR, and sleep mode
Observation
Behaviour as specified.Lower Temperature → lower energy consumption!
Note
If only the frequency generated by the LSB would be required (for output), then use the porttoggle feature of the OCR-module! This does not require an ISR call, and thus will also workwhen interrupts are currently disabled, e.g., by extended SC.
March 13, 2017 55
![Page 90: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/90.jpg)
How-to start programing a Microcontroller application (in Assembler)
Think about what you want to do
(obviously)
What ’features’ of the MC do you need?
Outputs/InputsADC/Timer/. . .
How should they interact? Are interrupts needed?
Consider the Control/Data-Flow (Petri-Net, state machine, structograms, flow chart, . . . )
Modularize (Functions)
Implement and test the modules.Use a consistent, and clean, programming style!
March 13, 2017 56
![Page 91: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/91.jpg)
How-to start programing a Microcontroller application (in Assembler)
Think about what you want to do (obviously)
What ’features’ of the MC do you need?
Outputs/InputsADC/Timer/. . .
How should they interact? Are interrupts needed?
Consider the Control/Data-Flow (Petri-Net, state machine, structograms, flow chart, . . . )
Modularize (Functions)
Implement and test the modules.Use a consistent, and clean, programming style!
March 13, 2017 56
![Page 92: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/92.jpg)
How-to start programing a Microcontroller application (in Assembler)
Think about what you want to do (obviously)
What ’features’ of the MC do you need?
Outputs/InputsADC/Timer/. . .
How should they interact? Are interrupts needed?
Consider the Control/Data-Flow (Petri-Net, state machine, structograms, flow chart, . . . )
Modularize (Functions)
Implement and test the modules.Use a consistent, and clean, programming style!
March 13, 2017 56
![Page 93: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/93.jpg)
How-to start programing a Microcontroller application (in Assembler)
Think about what you want to do (obviously)
What ’features’ of the MC do you need?
Outputs/InputsADC/Timer/. . .
How should they interact? Are interrupts needed?
Consider the Control/Data-Flow (Petri-Net, state machine, structograms, flow chart, . . . )
Modularize (Functions)
Implement and test the modules.Use a consistent, and clean, programming style!
March 13, 2017 56
![Page 94: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/94.jpg)
How-to start programing a Microcontroller application (in Assembler)
Think about what you want to do (obviously)
What ’features’ of the MC do you need?
Outputs/InputsADC/Timer/. . .
How should they interact? Are interrupts needed?
Consider the Control/Data-Flow (Petri-Net, state machine, structograms, flow chart, . . . )
Modularize (Functions)
Implement and test the modules.Use a consistent, and clean, programming style!
March 13, 2017 56
![Page 95: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/95.jpg)
How-to start programing a Microcontroller application (in Assembler)
Think about what you want to do (obviously)
What ’features’ of the MC do you need?
Outputs/InputsADC/Timer/. . .
How should they interact? Are interrupts needed?
Consider the Control/Data-Flow (Petri-Net, state machine, structograms, flow chart, . . . )
Modularize (Functions)
Implement and test the modules.Use a consistent, and clean, programming style!
March 13, 2017 56
![Page 96: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/96.jpg)
How-to start programing a Microcontroller application (in Assembler)
Think about what you want to do (obviously)
What ’features’ of the MC do you need?
Outputs/InputsADC/Timer/. . .
How should they interact? Are interrupts needed?
Consider the Control/Data-Flow (Petri-Net, state machine, structograms, flow chart, . . . )
Modularize (Functions)
Implement and test the modules.Use a consistent, and clean, programming style!
March 13, 2017 56
![Page 97: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/97.jpg)
Assembler Guidelines
Peak at the compiler output
gcc -S code.c create an assembler file.
this can be a good source of negative examples.
depending on optimizer parameters, this can be very verbose.
March 13, 2017 57
![Page 98: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/98.jpg)
Assembler Guidelines
Debug systematically
it is nearly impossible to code assembler “blindly”, i.e., without continuous testing.
debug only small code blocks simultaneously.
use LEDs to display current state (registers) while debugging.
March 13, 2017 58
![Page 99: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/99.jpg)
Assembler Guidelines
Be redundant (sometimes)
assembler code is very susceptible to hard-to-see mistakes.
e.g., create redundant labels just to clarify the control flow:
cpi r16, 1breq equals_one
not_equals_one:...
equals_one:...
label not equals one is redundant here, but documents the control flow.
March 13, 2017 59
![Page 100: 182.694 Microcontroller VU - Institute of Computer ... · No high-level language constructs, e.g., ... PA0 drives high-active LED. Turn that LED on. sbi DDRA, DDA0 ... use the port](https://reader031.fdocuments.in/reader031/viewer/2022022806/5cc86cab88c993a6188daa22/html5/thumbnails/100.jpg)
Questions?
March 13, 2017 60