14.02 Roust-A-Bout Couplings

Style 99 Roust-A-Bout couplings are designed with heavy housings and grips to provide

a strong component for joining plain and beveled end, including Schedule 80 steel pipe

and Victaulic plain end fittings. Roust-A-Bout couplings are not designed for use on plastic

pipe, pipe with brittle linings, cast or ductile iron pipe nor any pipe with a surface hardness

greater than 150 Brinell.

Pipe is secured together by heavy jaws, which are set into the housing. All sizes are

supplied with painted housings and plated nuts and bolts. Galvanized housings are

available.

WARNING

Style 99 Roust-A-Bout couplings must be assembled with nuts tightened to full torque

specifications.

Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM

A-395, grade 65-45-15, is available upon special request.

Housing Coating: Orange enamel.

• Optional: Hot dipped galvanized and others.

Jaws: Carbon steel, case hardened, electroplated, except sizes 1''; 76.1 mm and 139.7 mm, which

utilize stainless steel, Type 416, hardened.

Gasket: (specify choice*)

• Grade “E” EPDM

EPDM (Green color code). Temperature range –30°F to +230°F/–34°C to +110°C.

Recommended for cold and hot water service within the specified temperature range plus a

variety of dilute acids, oil-free air and many chemical services. UL classified in accordance

with ANSI/NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C potable water service. NOT

RECOMMENDED FOR PETROLEUM SERVICES.

• Grade “T” nitrile

Nitrile (Orange color code). Temperature range –20°F to +180°F/–29°C to +82°C.

Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the

specified temperature range. Not recommended for hot water services over +150°F/+66°C or

for hot dry air over +140°F/+60°C.

* Services listed are General Service Recommendations only. It should be noted that there are

services for which these gaskets are not recommended. Reference should always be made to

the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a

listing of services which are not recommended.

Bolts/Nuts/Washers: Heat-treated plated carbon steel, trackhead meeting the physical and chemical

requirements of ASTM A-449 and physical requirements of ASTM A-183. The 6"/150 mm and

larger sizes are supplied with hardened steel washers meeting ASTM F-436 Type 3 (weathering

steel).

MATERIAL SPECIFICATIONS

14.02_1

Roust-A-Bout® CouplingsSTYLE 99

14.02IPS CARBON STEEL PIPE – PLAIN END SYSTEM

JOB/OWNER CONTRACTOR ENGINEER

System No. __________________________ Submitted By ________________________ Spec Sect ____________ Para __________

Location ____________________________ Date ________________________________ Approved ___________________________

Date ________________________________

www.victaulic.com

VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.

REV_H

Exaggerated for clarity Exaggerated for clarity

1 ½ – 12'' SIZES

1 ½ – 18'' SIZES 1''; 76.1 & 139.7 MM SIZES

14 – 18'' SIZES

SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS

DIMENSIONS

Size

MaxWorkPress.

Max.EndLoad

RequiredBolt

Torque

‡Bolt/Nut

No. – SizeDimensionsInches/mm

Aprx.Weight

NominalSize

Inchesmm

ActualOutside

DiameterInches

mmpsikPa

Lbs. *N

Lb. Ft. **N•m Inches X Y Z

Lbs.kg

1 1.315 600 800 352 – 3⁄8 x 2

2.56 4.25 2.25 1.725 33.7 4130 3560 47.5 65 108 57 0.8

1 ½ 1.900 750 2100 602 – ½ x 2 ½

3.25 5.50 2.88 3.640 48.3 5175 9345 81.4 83 140 73 1.6

2 2.375 750 3300 1502 – 5⁄8 x 3 ¼

3.75 6.75 3.38 5.350 60.3 5175 14685 203.4 95 171 86 2.4

2 ½ 2.875 600 3890 1502 – 5⁄8 x 3 ¼

4.25 7.13 3.38 5.765 73.0 4130 17310 203.4 108 181 86 2.5

76.1 mm3.000 400 2825 95

2 – ½ x 2 ¾ 4.69 6.25 2.75 4.4

76.1 2700 12500 128.8 119 159 70 2.0

3 3.500 600 5770 2002 – ¾ x 4 ¼

5.00 8.50 3.38 8.780 88.9 4130 25676 271.2 127 216 86 3.9

3 ½ 4.000 500 6280 2002 – ¾ x 4 ¼

5.50 9.25 3.63 10.690 101.6 3450 27946 271.2 140 235 92 4.8

4 4.500 450 7155 2002 – ¾ x 4 ¼

6.13 10.00 4.00 12.8100 114.3 3100 31840 271.2 156 254 102 5.8

139.7 mm5.500 250 5940 160

2 – ¾ x 57.80 10.75 3.19 9.0

139.7 1700 26440 217.0 200 260 81 4.1

5 5.563 350 8500 2502 – 7⁄8 x 5

7.25 11.38 4.38 17.3125 141.3 2400 37825 339.0 184 289 111 7.8

6 6.625 300 10340 2502 – 1 x 6 #

8.50 13.38 4.38 23.2150 168.3 2065 46013 339.0 216 340 111 10.5

165.1 mm6.500 300 9955 250

2 – 1 x 6 #8.38 13.25 4.38 22.2

165.1 2065 44300 339.0 213 337 111 10.1

8 8.625 250 14600 2504 – 7⁄8 x 5 #

10.88 14.38 5.00 37.2200 219.1 1700 64970 339.0 276 365 127 16.9

10 10.750 250 22700 3004 – 7⁄8 x 5 #

13.38 16.38 5.00 48.2250 273.0 1700 101015 406.8 340 416 127 21.9

12 12.750 250 31900 3504 – 1 x 6 ½ #

15.50 19.63 5.13 60.0300 323.9 1700 141955 474.6 394 499 130 27.2

14 14.000 200 30800 3508 – 1 x 6 ½ #

16.75 20.75 5.38 89.0350 355.6 1400 137060 474.6 425 527 137 40.4

16 16.000 150 30200 3508 – 1 x 6 ½ #

19.00 22.63 5.38 105.0400 406.4 1000 134390 474.6 483 575 137 47.6

18 18.000 150 38200 3508 – 1 x 6 ½ #

21.00 23.50 5.38 125.0450 457.0 1000 169990 474.6 533 597 137 56.7

* Working Pressure and End Load are total, from all internal and external loads, based on coupling properly assembled, with bolts fully torqued to listed specifications, on plain end or beveled end standard weight (ANSI) steel pipe and Victaulic plain end fittings. Couplings are designed to be used with plain end pipe and Victaulic plain end fittings only.

** Bolt torque ratings shown must be applied at installation.

‡ Metric thread size bolts (plated) are available (color coded) for all coupling sizes upon request. Contact Victaulic for details.

WARNING: Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products.

# Supplied with flat washers.

Y Z

X

Y Z

X

ZY

X

1 – 6"/25 – 150 MM SIZES

8 – 12"/200 – 300 MM SIZES

14 – 18"/350 – 450 MM SIZES

14.02_2



www.victaulic.com


REV_H

1 2 3 4 5 6

Size Pipe Req’dBolt

Torque

Max.Joint

WorkingPressure

Max.Permiss.End LoadNominal

Outside SizeInches

mm

ActualOutside

DiameterInches

mm

WallThickness

Inchesmm Sched.

Lb.Ft.N • m

psikPa

Lbs.N

125

1.31533.7

0.17980

3547.5

— —4.55

0.13340

600 8003.38 4130 3560

0.10910

600 8002.77 4130 3560

0.0655

400 5501.65 2750 2450

1 ½ 40

1.90048.3

0.20080

6081.4

750 21005.08 5175 9345

0.14540

750 21003.68 5175 9345

0.10910

600 17002.77 4130 7565

0.0655

400 11001.65 2750 4895

250

2.37560.3

0.21880

150203.4

750 33005.54 5175 14685

0.15440

750 33003.91 5175 14685

0.10910

400 18002.77 2750 8010

0.0655

200 9001.65 1375 4005

2 ½ 65

2.87573.0

0.27680

150203.4

600 38907.01 4130 17310

0.20340

600 38905.16 4130 17310

0.12010

300 19003.05 2065 8455

0.0835

150 10002.11 1035 4450

380

3.50088.9

0.30080

200271.2

600 57707.62 4130 25675

0.21640

600 57705.49 4130 25675

0.12010

225 21603.05 1550 9610

0.0835

125 12002.11 860 5340

Table continued on page 4.

PRESSURE RATINGS AND END LOADS

Carbon Steel Pipe

14.02_3



www.victaulic.com


REV_H

1 2 3 4 5 6

Size PipeReq’dBolt

Torque

Max.Joint

WorkingPressure


Outside SizeInches

mm

ActualOutside

DiameterInches

mm

WallThickness

Inchesmm Sched.

Lb.Ft.N • m

psikPa

Lbs.N

3 ½ 90

4.000101.6

0.31880

200271.2

500 62808.08 3450 27945

0.22640

500 62805.74 3450 27945

0.12010

200 25003.05 1375 11125

0.0835

100 12502.11 690 5565

4100

4.500114.3

0.33780

200271.2

450 71558.56 3100 31840

0.23740

450 71556.02 3100 31840

0.12010

175 28003.05 1200 12460

0.0835

60 9502.11 415 4230

5125

5.563141.3

0.37580

250339.0

350 85009.53 2410 37825

0.25840

350 85006.55 2410 37825

0.13410

150 36003.40 1035 16020

0.1095

75 18002.77 515 8010

6150

6.625168.3

0.43280

250339.0

300 1034010.97 2065 46015

0.28040

300 103407.11 2065 46015

0.13410

100 35003.40 690 15575

0.1095

75 26002.77 515 11570

165.1 mm6.500165.1

0.250—

250339.0

300 99556.35 2065 44300

0.200—

175 60005.08 1200 26700

0.150—

100 35003.81 690 15575

8200

8.625219.1

0.32240

250339.0

250 146008.18 1725 64970

0.27730

200 117007.04 1375 52065

0.14810

100 60003.76 690 26700

0.1095

50 30002.77 345 13350



Carbon Steel Pipe

14.02_4



www.victaulic.com


REV_H

1 2 3 4 5 6


Torque

Max.Joint

WorkingPressure


Outside SizeInches

mm

ActualOutside

DiameterInches

mm

WallThickness

Inchesmm Sched.

Lb.Ft.N • m

psikPa

Lbs.N

10250

10.750273.0

0.36540

300406.8

250 227009.27 1725 101015

0.30730

175 159007.80 1200 70755

0.16510

75 68004.19 515 30260

0.1345

50 45003.40 345 20025

12300

12.750323.9

0.375STD

350474.6

250 319009.53 1725 141955

0.33030

150 191008.38 1035 84995

0.18010

100 127004.57 690 56515

0.1655

75 95004.19 515 42275

14 14.000 0.375STD

350 200 30800350 355.6 9.53 474.6 1375 137060

16 16.000 0.375STD

350 150 30200400 406.4 9.53 474.6 1035 134390

COLUMN 1: Victaulic couplings are identified by nominal pipe size.

COLUMN 2: Nominal pipe wall thickness.

COLUMN 3: Pipe wall thickness schedule as established in ANSI Standard B36, 10-70.

COLUMN 4: Bolt torque required for installing Victaulic plain end couplings to achieve pressure ratings listed in Column 5 and Permissible Maximum End Loads listed in Column 6.

TORQUE RATINGS MUST BE APPLIED AT INSTALLATION.

COLUMN 5: Maximum line pressure, including surge, to which a joint should be subjected, based on couplings assembled to full torque specifications on plain end or beveled end standard weight steel pipe and/or Victaulic plain end fittings. Working pressure ratings are based on pipe prepared in accordance with Victaulic specifications.

COLUMN 6: Maximum end load from all internal and/or external forces to which the joint should be subjected based on couplings assembled to full torque specifications.

NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼ ''/6.4 mm. This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement.

ROUST-A-BOUT STYLE 99 COUPLINGS ARE DESIGNED FOR USE WITH PLAIN END OR BEVELED END PIPE AND VICTAULIC PLAIN END FITTINGS ONLY.


Carbon Steel Pipe

14.02_5



www.victaulic.com


REV_H

1 2 3 4 5 6


Torque

Max.Joint

WorkingPressure


SizeInches

mm

ActualOutside

DiameterInches

mm

WallThickness

Inchesmm Sched.

Lb.Ft.N • m

psikPa

Lbs.N

133.4

1.31533.7

0.13340

35 600 8003.38 47.5 4130 3560

0.10910

35 400 5502.77 47.5 2750 2450

0.0655

35 250 3501.65 47.5 1725 1555

1 ½ 48.3

1.90048.3

0.14540

60 500 1.4003.56 81.4 3450 6230

0.10910

60 400 1.1002.77 81.4 2750 4895

0.0655 N/R N/R N/R

1.65

260.3

2.37560.3

0.15440

150 500 2.2003.91 203.4 3450 9790

0.10910

150 400 1.8002.77 203.4 2750 8010

0.0655 N/R N/R N/R

1.65

2 ½ 73.0

2.87573.0

0.20340

150 400 2.5005.16 203.4 2750 11125

0.12010

150 250 1.5005.16 203.4 1725 6675

0.0835 N/R N/R N/R

2.11

388.9

3.50088.9

0.21640

200 400 3.8005.49 271.2 2750 16910

0.12010

200 200 1.9003.05 271.2 1375 8455

0.0835 N/R N/R N/R

2.11

3 ½ 101.6

4.000101.6

0.22640

200 300 3.7005.74 271.2 2065 16465

0.12010

200 150 1.9003.05 271.2 1035 8455

0.0835 N/R N/R N/R

2.11

4114.3

4.500114.3

0.23740

200 250 3.9006.02 271.2 1725 17355

0.12010

200 80 1.3003.05 271.2 550 5785

0.0835 N/R N/R N/R

2.11

5141.3

5.563141.3

0.25840

250 200 4.8006.55 339.0 1375 21360

0.13410

250 75 1.8003.40 339.0 510 8010

0.1095 N/R N/R N/R

2.77



Stainless Steel Pipe

14.02_6



www.victaulic.com


REV_H

1 2 3 4 5 6


Torque

Max.Joint

WorkingPressure


SizeInches

mm

ActualOutside

DiameterInches

mm

WallThickness

Inchesmm Sched.

Lb.Ft.N • m

psikPa

Lbs.N

6168.3

6.625168.3

0.28040

250 200 6.8007.11 339.0 1375 30260

0.13410

250 75 2.6003.40 339.0 515 11570

0.1095 N/R N/R N/R

2.77

165.1 mm6.500165.1

0.28040

250 200 6.8007.11 339.0 1375 30260

0.13410

250 75 2.6003.40 339.0 515 11570

0.1095 N/R N/R N/R

2.77

8219.1

8.625219.1

0.32240

250 200 11.0008.18 339.0 1375 48950

0.14810

250 75 4.4003.76 339.0 515 19580

0.1095

250 25 1.4602.77 339.0 170 6495

10273.0

10.750273.0

0.36540

300 100 9.0009.27 406.8 690 40050

0.16510

300 50 4.5004.19 406.8 345 20025

0.1345

300 25 2.2503.40 406.8 170 10010

12323.9

12.750323.9

0.40640

350 100 12.75010.31 474.6 690 56735

0.18010

350 50 6.4004.67 474.6 345 28480

0.1565

350 25 3.2003.96 474.6 170 14240

NR = Not recommended

+ Contact Victaulic for details.








NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼ ''/6.4 mm). This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement.



Stainless Steel Pipe

14.02_7



www.victaulic.com


REV_H

1 2 3 4 5 6


Torque

Max.Joint

WorkingPressure


SizeInches

mm

ActualOutside

DiameterInches

mm

WallThickness

Inchesmm Sched.

Lb.Ft.N • m

psikPa

Lbs.N

125

1.31533.7

0.17980 N/R N/R N/R

4.55

0.13340

35 600 8003.38 47.5 4130 3560

0.10910

35 300 4002.77 47.5 2065 1780

0.0655

35 100 1351.65 47.5 690 601

1 ½ 40

1.90048.3

0.20080

60 500 14005.08 81.4 3450 6230

0.14540

60 400 11003.56 81.4 2760 4895

0.10910

60 300 8252.77 81.4 2065 3671

0.0655 N/R N/R N/R

1.65

250

2.37560.3

0.21880

150 400 18005.54 203.4 2760 8010

0.15440

150 300 13003.91 203.4 2065 5785

0.10910

150 200 9002.77 203.4 1380 4005

0.0655 N/R N/R N/R

1.65

2 ½ 65

2.87573.0

0.27680

150 350 22007.01 203.4 2415 9790

0.20340

150 275 17255.16 203.4 1895 7676

0.12010

150 150 10005.16 203.4 1035 4450

0.0835 N/R N/R N/R

2.11

380

3.50088.9

0.30080

200 300 28807.62 271.2 2065 12816

0.21640

200 200 19205.49 271.2 1380 8544

0.12010

200 100 9603.05 271.2 690 4272

0.0835 N/R N/R N/R

2.11



Aluminum Pipe*

14.02_8



www.victaulic.com


REV_H

1 2 3 4 5 6


Torque

Max.Joint

WorkingPressure


SizeInches

mm

ActualOutside

DiameterInches

mm

WallThickness

Inchesmm Sched.

Lb.Ft.N • m

psikPa

Lbs.N

3 ½ 90

4.000101.6

0.31880

200 250 31008.08 271.2 1725 13795

0.22640

200 200 25005.74 271.2 1380 11125

0.12010

200 100 12503.05 271.2 690 5563

0.0835 N/R N/R N/R

2.11

4100

4.500114.3

0.33780

200 200 32008.56 271.2 1380 14240

0.23740

200 150 24006.02 271.2 1035 10680

0.12010

200 50 8003.05 271.2 345 3560

0.0835 N/R N/R N/R

2.11

5125

5.563141.3

0.37580

250 150 36009.53 339.0 1035 16020

0.25840

250 100 24006.55 339.0 690 10680

0.13410

250 50 12003.40 339.0 345 5340

0.1095 N/R N/R N/R

2.77

6150

6.625168.3

0.43280

250 150 520010.97 339.0 1035 23140

0.28040

250 100 35007.11 339.0 690 15575

0.13410

250 50 17503.40 339.0 345 7788

0.1095

250 35 12252.77 339.0 240 5451

8200

8.625219.1

0.32240

250 150 90008.18 339.0 1035 40050

0.27730

250 100 60007.04 339.0 690 26700

0.25020

250 75 45006.35 339.0 515 20025

0.14810

250 50 30003.76 339.0 345 13350



Aluminum Pipe*

14.02_9



www.victaulic.com


REV_H

1 2 3 4 5 6


Torque

Max.Joint

WorkingPressure


SizeInches

mm

ActualOutside

DiameterInches

mm

WallThickness

Inchesmm Sched.

Lb.Ft.N • m

psikPa

Lbs.N

10250

10.750273.0

0.35640

300 100 90009.27 406.8 690 40050

0.30730

300 75 63007.80 406.8 515 28035

0.25020

300 50 45006.35 406.8 345 20025

0.16510

300 25 22504.19 406.8 172 10013

12300

12.750323.9

0.40640

300 100 1280010.31 406.8 690 56960

0.33030

300 75 95008.38 406.8 515 42275

0.25020

300 50 60006.35 406.8 345 26700

0.18010

300 25 31504.67 406.8 172 14018

* Aluminum Pipe – Alloy 6063-T6 or 6061-T6 in Schedule 80 and 40; Alloy 6063-T6 in Schedule 30, 20, 10 and 5.

NR = Not recommended








NOTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼ ''/6.4 mm. This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement.



Aluminum Pipe*

14.02_10



www.victaulic.com


REV_H

WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details.

This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be

installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the

right to change product specifications, designs and standard equipment without notice and without

incurring obligations.

NOTE

Reference should always be made to the I-100 Victaulic Field Installation Handbook for the product

you are installing. Handbooks are included with each shipment of Victaulic products for complete

installation and assembly data, and are available in PDF format on our website at www.victaulic.com.

INSTALLATION

14.02_11



www.victaulic.com


REV_H

WCAS-6UPKCK

14.02


IPS CARBON STEEL PIPE – PLAIN END SYSTEM

For complete contact information, visit www.victaulic.com

14.02 1671 REV H UPDATED 3/2007


14.02

14.02 Roust-A-Bout Couplings

Documents

Transcript of 14.02 Roust-A-Bout Couplings