139 Ampi Faa Ch4

39-A-04-00-00-00B-001H-A

39-A-AMPI-00-P

Air vehicle maintenance planning information

Chapter 04

Airworthiness limitations

F.A.A. approved

Second issue: 2006-11-28

Change 14: 2013-01-25

NOTE TO READERS

AW139 and AB139 are two names for the same product.They identify two batches of aircraft manufactured inconformity with a unique Type Certificate Data Sheet.Where not specifically declared, the content of thisdocument is applicable to both AW139 and AB139helicopters.

39-A-04-00-00-00B-001H-A

39-A-AMPI-00-P

THIS PAGE INTENTIONALLY LEFT BLANK

Effectivity: All 04 LOEP (F.A.A.)

2013-01-25 Page 1

39-A-AMPI-00-P

C = Changed module N = New moduleD = Deleted module R = Revised module

(*) The asterisks identify the modules changed, revised, added or deleted with this change

List of effective pages

Document identifier Page Date Effectivity

39-A-04-00-00-00A-000C-A 2 C 2013-01-25 * All - F.A.A. approved

39-A-04-00-00-00A-000H-A 2 C 2006-11-28 All - F.A.A. approved

39-A-04-10-00-00A-000A-A 14 C 2012-09-18 * All - F.A.A. approved

39-A-04-20-00-00A-000A-A 8 C 2011-12-19 All - F.A.A. approved

39-A-04-30-00-00A-000A-A 12 C 2011-12-19 All - F.A.A. approved

Dates of issue and changes are:Second issue 2006-11-28Change 14 2013-01-25

The Second Issue of this chapter, after the insertion of Change 14, includes the modules that follow:

Effectivity: All 04 LOEP (F.A.A.)

2013-01-25 Page 2

39-A-AMPI-00-P


39-A-AMPI-00-P

04 CR (F.A.A.)Page 1

2006-11-28

Change record

ChangeNo.

Incorporateddate by (signature)

ChangeNo.

Incorporateddate by (signature)

1 2008-03-13 AGU 26

2 2008-06-25 AGU 27

3 2008-07-21 AGU 28

4 2008-12-04 AGU 29

5 2009-02-06 AGU 30

6 2010-02-25 AGU 31

7 2010-02-26 AGU 32

8 2010-04-20 AGU 33

9 2010-04-21 AGU 34

10 2010-12-17 AGU 35

11 2011-11-18 AGU 36

12 2012-09-19 AGU 37

13 2012-09-19 AGU 38

14 2013-01-25 AGU 39

15 40

16 41

17 42

18 43

19 44

20 45

21 46

22 47

23 48

24 49

25 50


04 CR (F.A.A.)Page 2

2006-11-28

39-A-AMPI-00-P

39-A-AMPI-00-P

Effectivity: All 04 HI (F.A.A.)

2013-01-25 Page 1

Highlights

The listed changes are introduced with Change 14

Document Identifier Reason for update

39-A-04-00-00-00A-000C-A CHANGED - Added approval of Change 14

39-A-04-10-00-00A-000A-A CHANGED - Added ref. RL012B, RL016A, RL019C and RL019D. Changed Note 1 to table 4

39-A-AMPI-00-P

Effectivity: All 04 HI (F.A.A.)

2013-01-25 Page 2


Effectivity: All 04 TOC (F.A.A.)

2006-11-28 Page 1

39-A-AMPI-00-P

Table of contents

Technical Name Information Name Document Identifier Effectivity

Airworthiness Authority approval General 39-A-04-00-00-00A-000C-A All

Airworthiness limitations General 39-A-04-00-00-00A-000H-A All

Retirement lives General 39-A-04-10-00-00A-000A-A All

Mandatory inspections General 39-A-04-20-00-00A-000A-A All

Certification maintenance requirements

General 39-A-04-30-00-00A-000A-A All

Effectivity: All 04 TOC (F.A.A.)

2006-11-28 Page 2

39-A-AMPI-00-P


Effectivity: All - F.A.A. approved 39-A-04-00-00-00A-000C-A

2013-01-25 Page 1

39-A-AMPI-00-P

Airworthiness Authority approval – GeneralOriginat or:-PB------

Table of contentsReferences ................................................................................................................................... 11 Record of Airworthiness Authority approvals ..................................................................... 1

List of tables1 References ......................................................................................................................... 12 Record of Airworthiness Authority approvals ..................................................................... 1

References

Description

1 Record of Airworthiness Authority approvalsRefer to Table 2.

Table 2 Record of Airworthiness Authority approvals

Table 1 References

Data Module Title

No references

Revision number Subject F.A.A. approved

First Issue - - Approval No. R00002RD

Dated: December 20, 2004

Change 1 See Highlights (HI) page September 27, 2005

Change 2 See Highlights (HI) page May 22, 2006

Change 3 See Highlights (HI) page July 27, 2006


Change 5 See Highlights (HI) page October 02, 2006

Second Issue See Highlights (HI) page November 28, 2006

Change 1 See Highlights (HI) page March 13, 2008

Change 2 See Highlights (HI) page June 25, 2008


Change 4 See Highlights (HI) page December 04, 2008

Change 5 See Highlights (HI) page February 06, 2009

Effectivity: All - F.A.A. approved 39-A-04-00-00-00A-000C-A

2013-01-25 Page 2

39-A-AMPI-00-P

End of data module

Change 6 See Highlights (HI) page Approval No. EASA D (2010) / MMA/SFO/10.0170

Dated: 09 March 2010

Change 7 See Highlights (HI) page Approval No. EASA D (2009) / MMA/SFO/10.079

Dated: 17 February 2010

Change 8 See Highlights (HI) page Approval No. EASA D (2010) / MMA/SFO/10001895a

Dated: 20 April 2010

Change 9 See Highlights (HI) page Approval No. EASA D (2010) / MMA/SFO/10003903b

Dated: 20 April 2010

Change 10 See Highlights (HI) page Approval No. EASA D (2010) / MMA/NBB/10007089

Dated: 17 December 2010

Change 11 See Highlights (HI) page Approval No. EASA D (2011) / MMA/SSI/10011321

Dated 17 November 2011

Approval No. EASA D (2011) / MMA/SSI/10010053


Approval No. EASA D (2011) / MMA/SSI/10011322


Change 12 See Highlights (HI) page Approval No. EASA D (2012) / MMA/JDE/10011039+10015427

Dated 27 July 2012


Dated 18 September 2012


Dated 25 January 2013

Revision number Subject F.A.A. approved

Effectivity: All - F.A.A. approved 39-A-04-00-00-00A-000H-A

2006-11-28 Page 1

39-A-AMPI-00-P

End of data module

Airworthiness limitations – GeneralOriginat or:-PB06-004---

Table of contentsReferences ................................................................................................................................... 11 Airworthiness limitations..................................................................................................... 12 Airworthiness limitations data modules .............................................................................. 13 Engine airworthiness limitations ......................................................................................... 1

List of tables1 References ......................................................................................................................... 1

References

Description

1 Airworthiness limitationsThis chapter identifies the airworthiness limitations for the AW139 helicopter, i.e. those mandatoryreplacement requirements (hereinafter referred to as retirement lives) and mandatory inspectionswhich have been approved by F.A.A.

The airworthiness limitations cannot be changed without approval.

2 Airworthiness limitations data modulesThe airworthiness limitations include the data modules that follow:

– The retirement lives (39-A-04-10-00-00A-000A-A)– The mandatory inspections (39-A-04-20-00-00A-000A-A)– The certification maintenance requirements (39-A-04-30-00-00A-000A-A).

3 Engine airworthiness limitationsRefer to the latest issue of the engine maintenance manual for the airworthiness limitationsapplicable to the Pratt & Whitney Canada PT6C-67C engine.

Note The Airworthiness Limitations, specified for any Part Number quoted in this Chapter04, apply also to all successive Part Numbers having the same first ten digits anddiffetent last two digits, unless otherwise specified.

Table 1 References

Data Module Title

39-A-04-10-00-00A-000A-A Retirement lives – General

39-A-04-20-00-00A-000A-A Mandatory inspections – General

39-A-04-30-00-00A-000A-A Certification maintenance requirements – General

Effectivity: All - F.A.A. approved 39-A-04-00-00-00A-000H-A

2006-11-28 Page 2

39-A-AMPI-00-P


Effectivity: All 39-A-04-10-00-00A-000A-A

2012-09-18 Page 1

39-A-AMPI-00-P

Retirement lives – General

Table of contentsReferences ................................................................................................................................... 11 Introduction......................................................................................................................... 12 Retirement lives - Affected parts ........................................................................................ 23 Terms and definitions of Table 2 ........................................................................................ 23.1 Reference (Ref).................................................................................................................. 23.2 Part..................................................................................................................................... 23.3 Part number........................................................................................................................ 23.4 Retirement life .................................................................................................................... 24 External Hoist Operation .................................................................................................... 95 External Load Operation .................................................................................................. 106 Operation above 6400 kg (MTOW) .................................................................................. 117 Guidelines ........................................................................................................................ 12

List of tables1 References ......................................................................................................................... 12 Retirement lives - List of affected parts .............................................................................. 33 CAT. A Training Operations - Life penalty factor................................................................ 74 Rotor Starting or Stopping with wind speed above 27 kts - Life penalty factor .................. 85 External Hoist Lift - Life penalty factor................................................................................ 96 External Load Operation - Life penalty factor................................................................... 107 Operation above 6400 kg (MTOW) - Life penalty factor................................................... 11

References

Description

1 IntroductionThe parts listed in the Table 2 must be mandatorily retired from service when the indicatedretirement life is reached. This also applies to all those non-serialized standard parts whichconnect the identified assembly / component.

All retirement lives are expressed in Flying Hours (FH), unless otherwise specified. Flying hoursare defined as those hours accumulated from take-off to landing.

The retirement lives of some parts are expressed in “landings” because their life is dependentupon the rotor start-stop cycles and the helicopter ground-air-ground cycles.

If not differently specified, the retirement lives are based on the following assumptions:

– 800 landings in 100 flying hours, including 400 rotor start-stop cycles.– 20 percent of usage in CAT. A Training Operations, on yearly basis.– For External Load Operations: 6 External Load Cycles and 3 Landings per Flying Hour,

calculated on at least 100 FH basis

Table 1 References

Data Module Title

No references


2012-09-18 Page 2

39-A-AMPI-00-P

– For External Hoist Operations: 1.65 Lift per Flying Hour, calculated on at least 100 FH basis.

In the event that the actual usage exceeds these assumptions, the Operator shall contact theManufacturer.

If parts with the same part number have been interchanged between different AW139 variants,the retirement life of the part must be restricted to the lowest value between those variants onwhich the part has been installed.

For the following parts the Operator shall maintain the relevant log card and contact theManufacturer prior to approaching the 40000 FH for confirmation of the applicability of theairworthiness instructions provided in this chapter:

– Fuselage Structure Assembly, part number 3P5300A00132

2 Retirement lives - Affected partsRefer to Table 2.

3 Terms and definitions of Table 2

3.1 Reference (Ref)This column gives a reference [RL (Retirement Lives) plus a progressive number] which identifiesthe listed components.

3.2 PartThis column gives the part description.

3.3 Part numberThis column gives the part number.

3.4 Retirement lifeThis column gives the retirement life of the part. Unless specified differently, the retirement life itin flight hours.


2012-09-18 Page 3

39-A-AMPI-00-P

Table 2 Retirement lives - List of affected parts

Ref Part Part number Retirement life

RL001 Left Main Landing Gear Assembly (Liebherr landing gear installation)

3G3210V00133 21000 landings

Left Main Landing Gear Assembly (Liebherr landing gear installation)

3G3210V00135 50000 landings

Deleted

Right Main Landing Gear Assembly (Liebherr landing gear installation)

3G3210V00233 21000 landings

Right Main Landing Gear Assembly (Liebherr landing gear installation)

3G3210V00235 50000 landings

Deleted

RL002 Nose Landing Gear Assembly (Liebherr landing gear installation)

3G3220V00133 50000 landings

Deleted

RL002A Nose Landing Gear Assembly (Goodrich landing gear installation)

4G3220V00131 12500 landings

RL003 Main Retracting Actuator Assembly (Liebherr landing gear installation)

3G3230V00332 50000 landings

RL003A Main Retracting Actuator Assembly (Goodrich landing gear installation)

4G3230V00233 12500 landings

RL004 Nose Retracting Actuator Assembly (Liebherr landing gear installation)

3G3230V00132 50000 landings

RL004A Nose Retracting Actuator Assembly (Goodrich landing gear installation)

4G3230V00131 12500 landings

RL004B Left MLG Trailing Arm Assembly (Goodrich landing gear installation)

4G3210V00331 12500 landings

RL004C Right MLG Trailing Arm Assembly (Goodrich landing gear installation)

4G3210V00431 12500 landings

RL004D MLG Shock Absorber Assembly (Goodrich landing gear installation)

4G3210V00531 12500 landings

RL004E Forward Arm Assy (Goodrich landing gear installation)

4F3210A00131 12500 landings

RL005 TGB Fitting 3G5351A01151 7200

RL006 Tail Assembly 3G5350A00132 10000 FH or 32000 landings whichever comes first (Para 5)

RL007 Main Landing Gear LH Segment 3P5339A00332 80000 landings

Main Landing Gear RH Segment 3P5339A00432 80000 landings


2012-09-18 Page 4

39-A-AMPI-00-P

RL007A Rear Fuselage Assembly 3P5340A00132 32000 landings

RL007B Trailing Arm Pintle Pin (Goodrich landing gear installation)

3G5339A08351 11000 landings

RL008 Tailplane Attachment Fitting on Fin Upper 3G5351A01432 7600

Tailplane Attachment Fitting on Fin Upper 3G5351A01532 7600

RL009 Tailplane Attachment Fitting on Fin Lower 3G5351A07531 10600

RL010 Deleted

RL010A Rod End (Fin End) 3G5510A03931 4600 (Para 6)

RL010B Rod Sleeve 3G5510A04152 10000

RL010C Rod End (Tailplane End) 3G5510A04052 10000 (Para 6)

RL010D Tailplane Assembly 3G5510A00133 65000 (Para 6)

RL011 Main Landing Gear Actuator Bolt on Sponson Bracket

3G3210L00151 160000 landings

RL012 Main Rotor Blade Assembly 3G6210A00131 10000 (Table 3) (Table 4) (Para 6)

RL012A Main Rotor Blade Assembly with Heater Mat

4G6210A00132 6000 (Table 3) (Table 4) (Para 6)

RL012B Main Rotor Blade Assembly 3G6210A00134 20000 FH or 40000 landings or 5 years whichever comes first (Table 3) (Table 4) (Para 6)

RL013 Main Rotor Hub Assembly 3G6220A00332 46000 (Para 5)

RL014 Deleted

RL015 Main Rotor Rotating Swashplate 3G6230A00332 4800 (Para 4)

RL016 Main Rotor Scissors Attachment Flange Assembly

3G6220A00632 47450

RL016A Main Rotor Scissors Attachment Flange Assembly

3G6220A00633 Unlimited

RL017 Main Rotor Damper Bolt 3G6220A01251 51700

RL018 Main Rotor Elastomeric Bearing 3G6220V00153 100000 landings

Main Rotor Elastomeric Bearing 3G6220V00154 100000 landings

RL019 Upper Scissor Lever Assembly 3G6230A00832 14300

RL019A Deleted

RL019B Lower Scissor Lever Assembly 3G6230A00931 20100

RL019C Upper Scissor Lever Assembly 3G6230A00834 Unlimited



2012-09-18 Page 5

39-A-AMPI-00-P

RL019D Lower Scissor Lever Assembly 3G6230A00934 Unlimited

RL020 Deleted

RL021 MGB Case, Top Assembly 3G6320A01033 8800 FH or 23000 landings whichever comes first (Para 6)

MGB Case, Top Assembly 3G6320A01035 17000

RL022 MGB Shaft, Main Rotor 3G6320A01852 15300 FH or 54000 landings whichever comes first (Table 3) and (Para 4) and (Para 5)

RL023 MGB Case, Main Assembly 3G6320A02734 5000 FH or 27000 landings whichever comes first (Para 5)

MGB Case, Main Assembly 3G6320A02736 10000 FH or 77500 landings whichever comes first (Para 5)

RL024 MGB Upper Fitting 3G6330A00232 95800 landings (Para 6)

RL025 MGB Antitorque Beam 3G6330A00532 20000 FH or 63000 landings whichever comes first (Para 5)

RL026 Deleted

RL027 Deleted

RL028 Deleted

RL029 Deleted

RL030 Deleted

RL031 Deleted

RL032 Deleted

RL033 Tail Rotor Blade Assembly 3G6410A00131 10000

RL033A Tail Rotor Blade Assembly with Heater Mat 4G6410A00131 4033

RL034 Tail Rotor Hub Assembly 3G6420A00332 7500 (Para 6)

RL035 Tail Rotor Elastomeric Spherical Bearing 3G6420V00153 5000

Tail Rotor Elastomeric Spherical Bearing 3G6420V00154 5000

RL036 Tail Rotor Elastomeric Damper 3G6420V00455 20000



2012-09-18 Page 6

39-A-AMPI-00-P

RL037 Tail Rotor Shaft Drive Assembly, Number 1 3T6510A00141 100000 landings (Para 5)

Tail Rotor Shaft Drive Assembly, Number 2 3T6510A00238 16000 FH or 44800 landings whichever comes first (Para 5) (Para 6)

Tail Rotor Shaft Drive Assembly, Number 3 3T6510A00337 16000 FH or 44800 landings whichever comes first (Para 5) (Para 6)

RL038 Tail Rotor Drive Coupling 3T6510V00152 60000 landings (Para 5)

RL039 Deleted

RL040 TGB Input Flange Coupling 3T6521A07353 100000 landings (Para 5)

RL041 IGB Output Flange Coupling 3T6521A07353 100000 landings (Para 5)

RL042 TGB Output Housing 3T6522A05338 48000 landings (Para 5)

RL043 TGB Centre Housing 3T6522A05144 10000

RL044 IGB Input Flange Coupling 3G6521A00231 100000 landings (Para 5)

IGB Input Flange Coupling 3T6521A05657 100000 landings (Para 5)

RL045 IGB Housing assy centre 3T6521A05134 100000 landings (Para 5)

RL046 Deleted

RL047 External (Rescue) Hoist Cable Assembly BL-6260 1500 external hoist lifts or 4 years, whichever occurs first (see Para 4 for External Hoist Lift definitions)

External (Rescue) Hoist Cable Assembly BL-9149-8 1500 external hoist lifts or 4 years, whichever occurs first (see Para 4 for External Hoist Lift definitions)

External (Rescue) Hoist Cable Assembly 42325-298 1500 external hoist lifts or 4 years, whichever occurs first (see Para 4 for External Hoist Lift definitions)

RL048 Antitorque Beam Bolts 3G6330V00451 3G6330L00351

56000 56000

RL049 Ball-Spline Assembly 42277-118 17791

RL050 Cable Drum 42325-213 42360

RL051 Main Housing 44308-130 4600



2012-09-18 Page 7

39-A-AMPI-00-P

Table 3 CAT. A Training Operations - Life penalty factor

Ref Part Part number Life penalty factor

RL012 Main Rotor Blade Assembly 3G6210A00131 2.0


4G6210A00132 2.0

RL012B Main Rotor Blade Assembly 3G6210A00134 2.0

RL022 MGB Shaft, Main Rotor 3G6320A01852 1.7

RL031 Deleted

Note

1 CAT. A Training Operations.

– For the parts listed in Table 3 a life penalty must be mandatorily applied whenever CAT. ATraining Operations are performed.

– Flying hours (FH) spent in CAT. A Training must be multiplied by the specified factor. Thepenalty is applicable only to flying hours.

– FH spent in CAT. A Training Operations are defined as the total flying Hours (from take off tolanding) when at least one time the training mode is activated.

– E.g.: Main Rotor Blade Assembly: Flight time spent during CAT. A Training Operations = 1 FH. Total accumulated FH = 1 x 2.0 = 2.0 FH.


2012-09-18 Page 8

39-A-AMPI-00-P

Table 4 Rotor Starting or Stopping with wind speed above 27 kts - Life penalty factor


RL012 Main Rotor Blade Assembly 3G6210A00131 3.5


4G6210A00132 3.5

RL012B Main Rotor Blade Assembly 3G6210A00134 3.5 FH and 14 landings

Note

1 Rotor Starting or Stopping with wind speed above 27 kts.

– For the parts listed in Table 4 a life penalty must be mandatorily applied. – Increase the flying hours and the landings (if applicable) by the specified value for

each Rotor Start or Stop carried out with wind speed above 27 kts.– E.g.: Main Rotor Blade Assembly:

Rotor Start with wind speed above 27 kts. Flight Time = 1 FH. Rotor Stop with wind speed above 27 kts. Total accumulated FH = 3.5 + 1 + 3.5 = 8 FH.

– E.g.: Main Rotor Blade Assembly: Rotor Start with wind speed above 27 kts. Ground Time = 0.5 h. Flight Time = 0 FH. Rotor Stop with wind speed above 27 kts. Total accumulated FH = 3.5 + 0 + 3.5= 7 h.

– E.g.: Main Rotor Blade Assembly part number 3G6210A00134: Rotor Start with wind speed above 27 kts. Flight Time = 1 FH. Rotor Stop with wind speed above 27 kts. Total accumulated time = (3.5 + 1 + 3.5 = 8) FH and 14 landings.


2012-09-18 Page 9

39-A-AMPI-00-P

4 External Hoist OperationFor the parts listed in Table 5 a life penalty must be mandatorily applied whenever an externalhoist lift is performed.

The external hoist lift is defined as an unreeling and recovery of the cable with a load attached tothe hook, independent of the length of the cable that is deployed/recovered. An unreeling/recoveryof the cable with no load on the hook is not considered to be a lift. Any operation where a load isapplied for half the operation (i.e. unreeling or recovery) must be considered as one lift.

Increase the flying hour by the specified value for each external hoist lift. The penalty is applicableonly to flying hours.

Table 5 External Hoist Lift - Life penalty factor


RL015 Main Rotor Rotating Swashplate 3G6230A00332 0.5 (Note 1)

RL022 MGB Shaft, Main Rotor 3G6320A01852 Note 2

Note E.g.: Main rotor rotating swashplate: Flight time = 4 FH. Number of rescue hoist lifts = 3. Total accumulated FH = 4 + (0.5 x 3) = 5.5

1 For non zero-time components, whose accumulated life has been counted without this penalty factor, the total accumulated life must be updated as follows: Updated total accumulated flight hours = present total accumulated flight hours + 0.5 x accumulated external hoist lifts.

2 The life penalty factor due to external hoist operations has been deleted. For non zero-time components, whose accumulated life has been counted with the previous penalty factor, the total accumulated life may be updated as follows: Updated total accumulated life = present total accumulated life - 2.5 x accumulated external hoist lifts.

Present total accumulated life = 25 FH. Accumulated external hoist lifts = 5

Updated total accumulated life = 25 - 2.5 x 5 = 12.5 FH.


2012-09-18 Page 10

39-A-AMPI-00-P

End of data module

5 External Load OperationFor the following parts in Table 6 a life penalty must be mandatorily applied whenever an ExternalLoad Cycle is performed.

An External Load Cycle is every external load lift using the Cargo Hook.

Increase the Flying Hours and/or Landings by the specified value, as applicable, for each ExternalLoad Cycle.

Table 6 External Load Operation - Life penalty factor

Ref Part Part number Life penalty cargo hook

RL006 Tail Assembly 3G5350A00132 0.5 FH

RL013 Main Rotor Hub Assembly 3G6220A00332 1 FH

RL022 MGB Shaft, Main Rotor 3G6320A01852 2 Landings and 1 FH

RL023 Case, Main assembly 3G6320A02734 2 Landings

Case, Main assembly 3G6320A02736 2 Landings

RL025 Antitorque Beam 3G6330A00532 2 Landings and 1 FH

RL037 TR Shaft Drive Assembly - 1 3T6510A00141 2 Landings

TR Shaft Drive Assembly - 2 3T6510A00238 2 Landings

TR Shaft Drive Assembly - 3 3T6510A00337 2 Landings

RL038 TR Drive Couplings (KAMATICS) 3T6510V00152 2 Landings

RL039 Deleted

RL040 TGB Input Flange Coupling 3T6521A07353 2 Landings

RL041 IGB Output Flange Coupling 3T6521A07353 2 Landings

RL042 TGB Output Housing 3T6522A05338 2 Landings

RL044 IGB Input Flange Coupling 3G6521A00231 2 Landings

IGB Input Flange Coupling 3T6521A05657 2 Landings

RL045 IGB Housing assy centre 3T6521A05134 2 Landings

E.g.: For M/R Hub : Flight time = 2 FH. Number of External Load Cycles = 4. Total accumulatedFH = 2 + (1 x 4) = 6 FH.

E.g.: For M/R Shaft : Flight time = 5 FH. Number of Lifts = 3. Number of landings = 6. Totalaccumulated FH = 5 + (1 x 3) = 8 FH. Total accumulated landings = 6 + (2 x 3) = 12 Landings.


2012-09-18 Page 11

39-A-AMPI-00-P

End of data module

6 Operation above 6400 kg (MTOW)For the following parts in Table 7 a life penalty must be mandatorily applied to every flight (fromtake off to landing) in case the total weight exceeds 6400 kg at least one time.

In this case, Multiply the Flying Hours and/or Landings by the specified value, as applicable.

Table 7 Operation above 6400 kg (MTOW) - Life penalty factor


RL010A Rod End (Fin End) 3G5510A03931 4.5 FH

RL010C Rod End (Tailplane End) 3G5510A04052 4 FH

RL010D Tailplane Assembly 3G5510A00133 4 FH

RL012 Main Rotor Blade Assembly 3G6210A00131 2 FH


4G6210A00132 2 FH

RL012B Main Rotor Blade Assembly 3G6210A00134 2 FH

RL014 Deleted

RL021 MGB Case, Top Assembly (Note 1)

3G6320A01033 1.6 FH

RL024 MGB Upper Fitting 3G6330A00232 2 Landings

RL034 Tail Rotor Hub Assembly 3G6420A00332 1.25 FH

RL037 Tail Rotor Shaft Drive Assembly, Number 2

3T6510A00238 2 Landings

Tail Rotor Shaft Drive Assembly, Number 3

3T6510A00337 2 Landings

Note

1 Life penalty factor is not applicable to P/N 3G6320A01035 and subsequents.


2012-09-18 Page 12

39-A-AMPI-00-P

7 GuidelinesDaily recording of the following parameters is recommended:

– Flight Hours– Landings (coincides with the number of flights)– Flight Hours performed during Cat. A training as per Note 1 (ref. Table 2)– Rotor starts above 27 kts wind speed as per Note 2 (ref. Table 2)– Rotor stops above 27 kts wind speed as per Note 2 (ref Table 2)– External hoist lifts as per Para 4– External load cycles as per Para 5– Landings related to operations above 6400 kg as per Para 6– Flight Hours related to operations above 6400 kg as per Para 6.

Eg.: 1

– Total Daily Flight Hours = 7.5 FH– Daily Landings (coincides with the number of flight) = 6– Daily Flight Hours performed during Cat. A training as per Note 1 = 0– Daily rotor starts above 27 kts wind speed as per Note 2 = 2– Daily rotor stops above 27 kts wind speed as per Note 2 = 1– Daily external hoist lifts per Para 4 = 0– Daily external load cycles as per Para 5 = 0– Daily Landings related to operations above 6400 kg as per Para 6 = 3– Daily Flight Hours related to operations above 6400 kg as per Para 6 = 2.6.

Eg.: 2

– Total Daily Flight Hours = 7.5 FH– Daily Landings (coincides with the number of flight) = 6– Daily Flight Hours performed during Cat. A training as per Note 1 = 0– Daily rotor starts above 27 kts wind speed as per Note 2 = 2– Daily rotor stops above 27 kts wind speed as per Note 2 = 1– Daily external hoist lifts per Para 4 = 0– Daily external load cycles as per Para 5 = 7– Daily Landings related to operations above 6400 kg as per Para 6 = 3– Daily Flight Hours related to operations above 6400 kg as per Para 6 = 2.6.

For the main rotor blades the following applies:

Rotor starts/stops above 27 kts

Cat. A operations

Operations above

6400 kg

Consumed Life FH = (7.5 - 2.6) + (3.5 x 2 + 3.5 x 1) + (2 x 0) + (2 x 2.6)

Consumed Life = 20.6


2012-09-18 Page 13

39-A-AMPI-00-P

For the antitorque beam the following applies:

External Load Cycles

Consumed Life FH = 7.5 + (1 x 7)

Consumed Life = 14.5


2012-09-18 Page 14

39-A-AMPI-00-P



2011-12-19 Page 1

39-A-AMPI-00-P

Mandatory inspections – General

Table of contentsReferences ................................................................................................................................... 11 Introduction......................................................................................................................... 22 Affected parts ..................................................................................................................... 23 Terms and definitions of Table 2 ........................................................................................ 33.1 Reference (Ref).................................................................................................................. 33.2 Part..................................................................................................................................... 33.3 Task.................................................................................................................................... 33.4 Interval................................................................................................................................ 33.5 Reference (DMC) ............................................................................................................... 34 External hoist lift ................................................................................................................. 7

List of tables1 References ......................................................................................................................... 12 Mandatory inspections - List of affected parts.................................................................... 43 Mandatory inspections – Rescue hoist system (Breeze) ................................................... 64 Mandatory inspections – Double rescue hoist system (Goodrich) ..................................... 75 Mandatory inspections – Single rescue hoist system (Goodrich)....................................... 76 Rotor Starting or Stopping with wind speed above 27 kts - Additional inspections............ 7

References

Table 1 References

Data Module Title

39-A-25-91-01-01A-285A-K Hook assembly (rescue hoist) – General visual inspection

39-A-53-40-00-00A-286C-A Tail section - Tail gearbox attachment structure – Detailed inspection

39-A-53-10-00-00A-285A-A Forward section - Sponsons – General visual inspection

39-A-53-40-00-00A-286A-A Tail section - Fin rib attachment – Detailed inspection

39-A-53-40-00-00A-286B-A Tail section – Detailed inspection

39-A-53-10-00-00A-286A-A Forward section - Main gearbox rod attachment structure – Detailed inspection

39-A-53-10-00-00A-286B-A Forward section - Anti-torque beam attachment structure – Detailed inspection

39-A-53-40-00-00A-286G-A Tail section - Tail/rear fuselage attachment fittings – Detailed inspection

39-A-53-40-00-00A-286H-A Tail section - Aft spar to skin joint – Detailed inspection

39-A-53-10-00-00A-286V-A Forward section - Frame STA 5700 – Detailed inspection

39-A-53-10-00-00A-286E-A Forward section - Engine attachment internal backup structure – Detailed inspection


2011-12-19 Page 2

39-A-AMPI-00-P

Description

1 IntroductionThe parts listed in the following schedule must be mandatorily inspected when the indicatedinterval is reached.

2 Affected partsRefer to Table 2.

39-A-53-10-00-00A-286W-A Forward section - Rescue hoist external backup structure – Detailed inspection

39-A-53-10-00-00A-286X-A Forward section - Double rescue hoist external backup structure – Detailed inspection

39-A-53-10-00-00A-286Y-A Forward section - Single rescue hoist external backup structure – Detailed inspection

39-B-53-10-00-00A-287A-K Forward section - Main landing gear backup structures – Special detailed inspection

39-B-53-10-00-00A-286B-K Fuselage Structure Assembly (frame STA 5700, RH/LH side, lower area) – Detailed inspection

39-A-62-11-00-00A-285A-A Main rotor blade installation - Blades – General visual inspection

39-A-62-22-00-00A-286C-A Main rotor head - Elastomeric bearings – Detailed inspection

39-A-62-22-00-00A-286F-A Main rotor head - Main rotor hub – Detailed inspection

39-A-62-31-06-00A-286A-A Swashplate - Rotating swashplate and duplex bearing attaching parts – Detailed inspection

39-B-62-11-01-00A-286A-A Main rotor blade – Detailed inspection

39-A-64-11-00-00A-285A-A Tail rotor blade installation - Blades – General visual inspection

39-A-64-11-00-00A-286B-A Tail rotor blade installation - Elastomeric bearings – Detailed inspection

39-A-64-21-00-00A-286D-A Tail rotor head installation - Lag damper elastomer – Detailed inspection

39-A-75-51-00-00A-286A-K Engine inlet particle separator system - Number 1 and Number 2 main panels – Detailed inspection

39-A-25-91-01-00A-285A-K Rescue hoist - Bumper assembly, cable cutter and cable – General visual inspection

39-A-25-94-01-00A-285A-K Double rescue hoist - Bumper assembly, cable cutter and cable – General visual inspection

39-A-25-96-01-00A-285A-K Single rescue hoist - Bumper assembly, cable cutter and cable – General visual inspection

Table 1 References

Data Module Title


2011-12-19 Page 3

39-A-AMPI-00-P

3 Terms and definitions of Table 2

3.1 Reference (Ref)This column gives the unique reference [MI (Mandatory Inspections) plus the system numberfollowed by a progressive number] which identifies the part.

3.2 PartThis column gives the part.

3.3 TaskThis column gives the description of the inspection to perform.

3.4 IntervalThis column gives the inspection interval for the part. Unless otherwise specified, the inspectioninterval is in Flying Hours (FH).

3.5 Reference (DMC)This column shows the Data Module Code which provides the instructions to perform theinspection.


2011-12-19 Page 4

39-A-AMPI-00-P

Table 2 Mandatory inspections - List of affected parts

Ref Part Task Interval Reference (DMC)

MI25-01 D-Lock External Hoist Hook

General visual inspection for damage

Daily 39-A-25-91-01-01A-285A-K

MI53-01 TGB Fitting (fasteners in skin and spar)

Detailed inspection for cracks (both internal and external sides)

300 39-A-53-40-00-00A-286C-A

MI53-02 Main Landing Gear LH Panel


600 39-A-53-10-00-00A-285A-A

MI53-03 Main Landing Gear RH Panel


600 39-A-53-10-00-00A-285A-A

MI53-04 Tail Structure Assembly (fin rib attachment area)


100 39-A-53-40-00-00A-286A-A

MI53-05 Tail Structure Assembly (tail cone RH/LH panels upper and lower joint)


300 39-A-53-40-00-00A-286B-A

MI53-06 Tail Structure Assembly (tail cone joint STA 11020)


300 39-A-53-40-00-00A-286B-A

MI53-07 Fuselage Structure Assembly (forward MGB rod backup structure)

Detailed inspection for cracks

300 39-A-53-10-00-00A-286A-A

MI53-08 Fuselage Structure Assembly (aft MGB rod backup structure and fitting part number 3P5330A11251)


300 (Note 8) 39-A-53-10-00-00A-286A-A

MI53-09 Fuselage Structure Assembly (antitorque beam backup structure)


300 39-A-53-10-00-00A-286B-A

MI53-10 Tail Structure Assembly (tail/rear fuselage attachment fittings)


200 39-A-53-40-00-00A-286G-A

MI53-11 Tail Structure Assembly (aft/front spar to skin joint)


100 39-A-53-40-00-00A-286H-A

MI53-12 Fuselage Structure Assembly (frame STA 5700, RH/LH side)


100 (Note 5) (Note 6) (Note 7)

39-A-53-10-00-00A-286V-A

MI53-13 Internal Engine Attachment Backup Structure


1200 39-A-53-10-00-00A-286E-A


2011-12-19 Page 5

39-A-AMPI-00-P

MI53-14 Fuselage Structure Assembly (external hoist backup structure) (Note 3)


4000 External Hoist Lifts (see Para 4)

39-A-53-10-00-00A-286W-A

MI53-14 Fuselage Structure Assembly (external hoist backup structure) (Note 4)


4000 External Hoist Lifts (see Para 4)

39-A-53-10-00-00A-286X-A 39-A-53-10-00-00A-286Y-A

MI53-15 Main landing gear backup structure LH/RH side (Goodrich landing gear installation)

Special detailed inspection for cracks (by using eddy corrent inspection method)

1250 Landings

39-B-53-10-00-00A-287A-K

MI53-16 Fuselage Structure Assembly (frame STA 5700, LH/RH side, lower area) (Goodrich landing gear installation)

Detailed inspection for cracks (nut and washer removal required only in the lowest attaching position)

7000 Landings

39-B-53-10-00-00A-286B-K

MI62-01 Main Rotor Blade Assembly


50 (Note 2) 39-A-62-11-00-00A-285A-A

MI62-02 Main Rotor Elastomeric Bearing (part number 3G6220V00153)

Detailed inspection for cracks in the elastomer

50 39-A-62-22-00-00A-286C-A

MI62-03 Main Rotor Elastomeric Bearing (part number 3G6220V00154)


50 39-A-62-22-00-00A-286C-A

MI62-04 Main Rotor Hub Assembly

Detailed inspection (without removal of blades)

2500 39-A-62-22-00-00A-286F-A

MI62-05 Deleted

MI62-06 Main Rotor Rotating Swashplate

Inspection for integrity and loss of torque of the bolts and ring retaining the duplex bearing

134 39-A-62-31-06-00A-286A-A

MI62-07 Main Rotor Blade Assembly with Heater Mat (part number 4G6210A00132)

Detailed inspection (hammer tapping) of the bonding area between tip cap and blade (from STA 6300 to STA 6400) for debondings and/or delaminations (blade removal not required)

100 39-B-62-11-01-00A-286A-A

MI64-01 Tail Rotor Blade Assembly


50 (Note 2) 39-A-64-11-00-00A-285A-A



2011-12-19 Page 6

39-A-AMPI-00-P

End of data module

Table 3 Mandatory inspections – Rescue hoist system (Breeze)

MI64-02 Tail Rotor Elastomeric Spherical Bearing (part number 3G6420V00153)


100 39-A-64-11-00-00A-286B-A

MI64-03 Tail Rotor Elastomeric Spherical Bearing (part number 3G6420V00154)


25 39-A-64-11-00-00A-286B-A

MI64-04 Tail Rotor Damper Detailed inspection for cracks in the elastomer

100 39-A-64-21-00-00A-286D-A

MI71-00 Engine Air Particle Separator Left and Right Main Panels (part numbers 3G7160V00551 and 3G7160V00651)

Detailed inspection for cracks in the panels

25 39-A-75-51-00-00A-286A-K

Note

1 Deleted.

2 Rotor Starting or Stopping with wind speed above 27 kts. For each Rotor Start or Stopperformed with wind speed above 27 kts the additional inspections reported in Table 3 must bemandatorily carried out.

3 Helicopters AW139 that have the Breeze rescue hoist system installed.

4 Helicopters AW139 that have the Goodrich rescue hoist system installed.

5 The 100 FH interval is extended to 1200 FH if the retro modification P/N 3G5306P08512 is appliedto the frames P/N 3P5338A13352 (LH) and 3P5338A13452 (RH).

6 The inspection requirement is not applicable to helicopters that install the following frame P/N:3P5338A13354 (LH) and 3P5338A13454 (RH).

7 The 100 FH interval is extended to 1200 FH if the retro modification P/N 3G5306P22311 is appliedto the frames P/N 3P5338A13353 (LH) and 3P5338A13453 (RH).

8 When the 3750 FH are reached, the 300 FH interval is reduced to 150 FH if the retro modificationP/N 3G5306P36711 or P/N 3G5306P39211 is not applied.


MI25-02 Rescue hoist GVI of entire usable length of the cable for damage and condition

Prior the first use of the day

39-A-25-91-01-00A-285A-K



2011-12-19 Page 7

39-A-AMPI-00-P

End of data module

Table 4 Mandatory inspections – Double rescue hoist system (Goodrich)

Table 5 Mandatory inspections – Single rescue hoist system (Goodrich)

Table 6 Rotor Starting or Stopping with wind speed above 27 kts - Additional inspections

4 External hoist liftThe external hoist lift is defined as an unreeling and recovery of the cable with a load attached tothe hook, independent of the length of the cable that is deployed/recovered.

An unreeling/recovery of the cable with no load on the hook is not considered to be a lift.

Any operation where a load is applied for half the operation (i.e. unreeling or recovery) must beconsidered as one lift.


MI25-03 Rescue hoist cable Do a GVI of the maximum length of cable used during the day operation for damage and condition

After the last flight of the day or before the first flight of the day if the rescue hoist is used or it is envisaged to be used

39-A-25-94-01-00A-285A-K


MI25-04 Rescue hoist cable Do a GVI of the maximum length of cable used during the day operation for damage and condition

After the last flight of the day or before the first flight of the day if the rescue hoist is used or it is envisaged to be used

39-A-25-96-01-00A-285A-K


MI62-01 Main Rotor Blade Assembly


Within 15 FH from the event

39-A-62-11-00-00A-285A-A

MI64-01 Tail Rotor Blade Assembly


Within 15 FH from the event

39-A-64-11-00-00A-285A-A


2011-12-19 Page 8

39-A-AMPI-00-P



2011-12-19 Page 1

39-A-AMPI-00-P

Certification maintenance requirements – General

Table of contentsReferences ................................................................................................................................... 11 Certification maintenance requirements............................................................................. 32 Column terms definitions.................................................................................................... 32.1 Reference (Ref).................................................................................................................. 32.2 System ............................................................................................................................... 32.3 Task.................................................................................................................................... 32.4 Interval................................................................................................................................ 32.5 Reference (DMC) ............................................................................................................... 32.6 Initials ................................................................................................................................. 3

List of tables1 References ......................................................................................................................... 12 Certification maintenance requirements............................................................................. 43 Certification maintenance requirements - Rescue hoist system (Breeze).......................... 74 Certification maintenance requirements - Double rescue hoist system (Goodrich) ........... 85 Certification maintenance requirements - Single rescue hoist system (Goodrich)............. 9

References

Table 1 References

Data Module Title

39-A-34-23-00-00A-321A-A Attitude heading reference system – Operational check

39-A-23-10-00-00A-321A-A Speech communications - Backup function – Operational check

39-A-34-61-00-00A-321A-A Flight management system - MCDU backup function – Operational check

39-B-31-61-00-00A-321B-A Central display system - Display controllers – Operational check

39-A-24-61-00-00A-321A-A DC electrical load distribution system - Essential bus feed circuit breakers – Operational check

39-A-24-32-00-00A-321A-A Battery power generation system - Diode modules – Operational check

39-A-24-31-00-00A-321A-A DC main generation system - Generator control units – Operational check

39-B-24-21-00-00A-321B-A AC generation system - Number 2 AC generator control unit – Operational check

39-B-24-21-00-00A-321C-A AC generation system - Number 2 power distribution unit – Operational check

39-B-24-21-00-00A-365A-A AC generation system - Connections between generator control units and IPS/AGB status panel – Continuity check

39-A-25-92-00-00A-344A-K Cargo hook system - Relay K40 – Functional check


2011-12-19 Page 2

39-A-AMPI-00-P

39-A-26-10-00-00A-321A-A Detection - Sensing element pressure transducers – Operational check

39-A-30-60-00-00A-344B-K Full ice protection system - Ice detector box function – Functional check

39-A-30-64-00-00A-344B-K Ice detection system - Pressure switches and shut off valves – Functional check

39-B-63-20-05-48A-286A-K Freewheel actuator - Freewheel inner race (main gearbox right input shaft module) – Detailed inspection

39-A-64-21-00-00A-286A-A Tail rotor head installation - Lag damper spherical bearings – Detailed inspection

39-A-67-10-00-00A-314A-A Main rotor control - Balance springs – Visual check

39-A-76-10-00-00A-321A-A Power controls - Overspeed limiters – Operational check

39-A-95-61-00-00A-321A-K Emergency flotation system - FLOAT switches – Operational check

39-A-25-91-00-00A-321A-K Rescue hoist system - Limit switches and cable foul assembly – Operational check

39-A-25-91-01-00A-321A-K Rescue hoist - Handwheel assembly bearing – Operational check

39-A-25-91-01-00A-285A-K Rescue hoist - Bumper assembly, cable cutter and cable – General visual inspection

39-A-04-20-00-00A-000A-A Mandatory inspections – General

39-A-25-94-00-00A-321A-K Double rescue hoist system - Limit switches – Operational check

39-A-25-94-00-00A-321B-K Double rescue hoist system - Cable cutter circuit and cable foul assembly – Operational check

39-A-25-94-01-00A-285A-K Double rescue hoist - Bumper assembly, cable cutter and cable – General visual inspection

39-A-25-94-00-00A-321C-K Double rescue hoist system - Deceleration and limit switches – Operational check

39-A-05-51-00-00A-000A-A Out of phase maintenance checks – General

39-A-25-96-00-00A-321A-K Single rescue hoist system - Limit switches and cable foul assembly – Operational check

39-A-25-96-00-00A-321B-K Single rescue hoist system - Cable cutter circuit – Operational check

39-A-25-96-01-00A-285A-K Single rescue hoist - Bumper assembly, cable cutter and cable – General visual inspection

39-A-25-96-00-00A-321C-K Single rescue hoist system - Deceleration and limit switches – Operational check

Table 1 References

Data Module Title


2011-12-19 Page 3

39-A-AMPI-00-P

Description

1 Certification maintenance requirementsThe Table 2 thru Table 5 that follows gives the data about the mandatory maintenance checksthat were identified during the certification process.

Parts listed in the following schedule must be mandatorily inspected when the indicated intervalis reached.

2 Column terms definitions

2.1 Reference (Ref)This column gives the unique reference [CM (Certification Maintenance) plus the system numberfollowed by a progressive number] which identifies each listed task.

2.2 SystemThis column gives the technical name of the system.

2.3 TaskThis column gives the description of the work to do.

2.4 IntervalThis column gives the maintenance check interval for the component. Unless specified differently,the interval is in Flying Hours (FH).

2.5 Reference (DMC)This column shows the Data Module Code which gives the instructions to do the check.

2.6 InitialsWhen you use a copy of the data module for maintenance record purposes, this column, gives thespace to write the initials of the person who did the check.


2011-12-19 Page 4

39-A-AMPI-00-P

Table 2 Certification maintenance requirements

Ref System Task Interval Reference (DMC) Initials

CM22-01 Automatic Flight Control

OC of MAU AHRS input 1500 39-A-34-23-00-00A-321A-A

CM23-01 Communication OC of MCDU and audio panel backup functions (ICS backup relays will be checked when performing this task)

1200 39-A-23-10-00-00A-321A-A

39-A-34-61-00-00A-321A-A

CM23-02 Communication OC of CCDs selection switches

1200 39-B-31-61-00-00A-321B-A

CM24-01 Electrical Power OC of essential bus feed circuit breakers (CB3, CB4, CB47 and CB48)

600 39-A-24-61-00-00A-321A-A

CM24-02 Electrical Power OC of diode modules (CR3, CR23 and CR24)

1200 39-A-24-32-00-00A-321A-A

CM24-03 Electrical Power OC of GCU over-voltage protection function

300 39-A-24-31-00-00A-321A-A

CM24-04 AC Generation System (FIPS)

OC to verify the correct functionality of the number 2 Generator Control Unit (GCU)

300 39-B-24-21-00-00A-321B-A

CM24-05 AC Generation System (FIPS)

OC to verify the correct reconfiguration of the number 2 Power Distribution Panel (PDP) when number 2 Generator is failed

20000 39-B-24-21-00-00A-321C-A

CM24-06 Ice Protection System Cables Interfacing

OC to verify the electrical continuity between GCU’s and IPS-AGB Status Panel (Channel A and Channel B)

20000 39-B-24-21-00-00A-365A-A

CM25-09 Cargo Hook Functional check of relay K40 for dormant open circuit failures

2000 39-A-25-92-00-00A-344A-K

CM25-26 Landing gear control valve (Goodrich landing gear installation)

Do a FC to detect internal leaks

5000 Note 4

CM26-01 Engine Fire Protection

OC of pressure transducer alarm switch contacts

3000 39-A-26-10-00-00A-321A-A

CM30-01 Ice Protection System (FIPS)

OC to verify the correct functionality of the Ice Detector Box 1 (IDB) functions

200 39-A-30-60-00-00A-344B-K


2011-12-19 Page 5

39-A-AMPI-00-P


OC to verify the correct functionality of the number 1 pressure switch bleed lines

10000 39-A-30-64-00-00A-344B-K


OC to verify the correct functionality of the number 1 shut-off valve bleed lines

10000 39-A-30-64-00-00A-344B-K


OC to verify the correct functionality of the Ice Detector Box 2 (IDB) functions

200 39-A-30-60-00-00A-344B-K


OC to verify the correct functionality of the number 2 pressure switch bleed lines

10000 39-A-30-64-00-00A-344B-K


OC to verify the correct functionality of the number 2 shut-off valve bleed lines

10000 39-A-30-64-00-00A-344B-K

CM63-01 Right Input Freewheel Shaft (Main gearbox equipped with AGB system)

DI of the roller bearing inner race (most internal) for damage and condition (freewheel shaft and actuator removal required)

600 39-B-63-20-05-48A-286A-K

CM64-01 Tail Rotor and Rotating Controls

DI of tail rotor damper spherical bearings for condition, damage and play

25 39-A-64-21-00-00A-286A-A

If special tool is available, removal is not required. Axial play check only. Maximum play allowed: 0.1 mm (0.0039 in)

CM67-01 Fixed Flight Control

VC of pitch, roll and yaw anchor spring mechanisms

1200 / 2 years

39-A-67-10-00-00A-314A-A

CM67-02 Main Rotor and Tail Rotor Servoactuators

Check of redundant seal sets 3000 Note 2

CM71-01 Engine Installation

OC of the NF/NPT overspeed limiter in the auto engine control system

3500 39-A-76-10-00-00A-321A-A

CM71-02 Engine Power Available Trend Monitoring (3-Display Helicopter Only)

Perform and record on the suitable provided forms (see PT6C-67C Engine Maintenance Manual) the power assurance check trend of both the engines

100 Note 3



2011-12-19 Page 6

39-A-AMPI-00-P

CM71-03 Engine Power Available Trend Monitoring (4-Display Helicopter Only)

Perform and record on the suitable provided forms (see PT6C-67C Engine Maintenance Manual) the power assurance check trend of both the engines

50 Note 3

CM95-01 Flotation System

OC of the guarded late arm switches located on the pilot and co-pilot collective grips for dormant closed circuit failures of the switch guard contacts and the push button contacts

800 39-A-95-61-00-00A-321A-K

Note

1 No tolerance above published intervals is allowed on Certification Maintenance Requirements.

2 Task to be performed by sending the components to the Manufacturer.

3 Task to be performed by following the instructions contained in the last issue of P&W PT6C-67CEngine Maintenance Manual.

4 At the specified limit the component will be replaced and the removed item will be sent to the VendorSupplier for schedule activities.



2011-12-19 Page 7

39-A-AMPI-00-P

Table 3 Certification maintenance requirements - Rescue hoist system (Breeze)


CM25-01 Rescue Hoist OC of the full-out and full-in limit switches of the hoist assembly for correct operation


39-A-25-91-00-00A-321A-K

CM25-02 Rescue Hoist OC of the intermediate speed limit switch of the hoist assembly for correct operation


39-A-25-91-00-00A-321A-K

CM25-03 Rescue Hoist OC of the handwheel assembly bearing of the hook assembly for freedom of rotation


39-A-25-91-01-00A-321A-K

CM25-04 Rescue Hoist GVI of the bumper assembly of the hook assembly for damage and condition

Daily 39-A-25-91-01-00A-285A-K

CM25-05 Rescue Hoist GVI of cable cutter of the hoist assembly to make sure that the cotter pin is correctly installed


39-A-25-91-01-00A-285A-K

CM25-06 Rescue Hoist OC of the cable foul assembly of the hoist assembly for correct operation


39-A-25-91-00-00A-321A-K

CM25-07 Transferred (Note 3)

CM25-08 Rescue Hoist After use in a salt water environment, clean the cable and the hook assembly with fresh water, then dry with a lint free cloth

After the last use of the day

Note 2

Note


2 Task to be performed by an Operator qualified by the Equipment Manufacturer, following theinstructions contained in the last issue of the relevant Component Maintenance Manual.

3 Task transferred to AMPI CHAPTER 04 AIRWORTHINESS LIMITATIONS - Mandatory inspections- General (39-A-04-20-00-00A-000A-A).


2011-12-19 Page 8

39-A-AMPI-00-P

Table 4 Certification maintenance requirements - Double rescue hoist system (Goodrich)


CM25-10 Rescue Hoist (part number 3G2591V01531)

OC of the rescue hoist assembly full-out limit and full-stop limit switch function to ensure correct operation

20 39-A-25-94-00-00A-321A-K

Rescue Hoist (part number 3G2591V01532)


450 39-A-25-94-00-00A-321A-K


OC of the rescue hoist assembly cable foul detection circuit to ensure hoisting operations stop and indications are generated

20 39-A-25-94-00-00A-321B-K



450 39-A-25-94-00-00A-321B-K




GVI of the full cable length for damage and condition

20 39-A-25-94-01-00A-285A-K



450 39-A-25-94-01-00A-285A-K



2011-12-19 Page 9

39-A-AMPI-00-P

Table 5 Certification maintenance requirements - Single rescue hoist system (Goodrich)

CM25-16 Rescue Hoist OC of the rescue hoist assembly deceleration switches S7 and S8 and caution limit switches S5 and S6 for dormant closed circuit failure of either one of the switches in series

5000 or rescue hoist assembly overhaul (Note 3)

39-A-25-94-00-00A-321C-K

CM25-17 Rescue Hoist OC of the rescue hoist assembly full-out limit switches S3 and S4 and full-stop limit switches S1 and S2 for dormant closed circuit failure of either one of the switches in series


39-A-25-94-00-00A-321C-K

Note


2 Task transferred to AMPI Chapter 05 - Out of phase maintenance checks - General (39-A-05-51-00-00A-000A-A).

3 Use the limit that occurs first.




20 39-A-25-96-00-00A-321A-K



450 39-A-25-96-00-00A-321A-K



2011-12-19 Page 10

39-A-AMPI-00-P



20 39-A-25-96-00-00A-321B-K



450 39-A-25-96-00-00A-321B-K





20 39-A-25-96-01-00A-285A-K



450 39-A-25-96-01-00A-285A-K


CM25-24 Rescue Hoist OC of the rescue hoist assembly deceleration switches S7 and S8 and caution limit switches S5 and S6 for dormant closed circuit failure of either one of the switches in series


39-A-25-96-00-00A-321C-K

CM25-25 Rescue Hoist OC of the rescue hoist assembly full-out limit switches S3 and S4 and full-stop limit switches S1 and S2 for dormant closed circuit failure of either one of the switches in series


39-A-25-96-00-00A-321C-K



2011-12-19 Page 11

39-A-AMPI-00-P

End of data module

Note


2 Task transferred to AMPI Chapter 05 - Out of phase maintenance checks - General (39-A-05-51-00-00A-000A-A).

3 Use the limit that occurs first.



2011-12-19 Page 12

39-A-AMPI-00-P


139 Ampi Faa Ch4

Documents

Transcript of 139 Ampi Faa Ch4