1 ULTRA & MILLENNIUM SECURITY CASE …...R-07.11.07 STR-08335-0142 3 ULTRA & MILLENNIUM SECURITY...
8
R-07.11.07 STR-08335-0142 ULTRA & MILLENNIUM SECURITY CASE INSTRUCTIONS
Transcript of 1 ULTRA & MILLENNIUM SECURITY CASE …...R-07.11.07 STR-08335-0142 3 ULTRA & MILLENNIUM SECURITY...
R-0
7.11
.07
STR
-083
35-0
142
1
ULT
RA
& M
ILLE
NN
IUM
SEC
UR
ITY
CA
SE IN
STR
UC
TIO
NS
R-0
7.11
.07
STR
-083
35-0
142
2
ULT
RA
& M
ILLE
NN
IUM
SEC
UR
ITY
CA
SE IN
STR
UC
TIO
NS
3 00060-1123 10 x 5/8 sheet metal screw3 00060-1370 10-16 x 3/4 tek screw2 00060-1064 10-32 x 1/2 machine screw2 00060-1155 10-32 hex nut2 00060-1166 1/4 washer2 08601-2087 36” double sided tape
QTY PART # DESCRIPTION
HARDWARE INCLUDED
doorassembly
existing gondola
left end panel
support strap right end panel
top shelf
gap filler
R-0
7.11
.07
STR
-083
35-0
142
3
ULT
RA
& M
ILLE
NN
IUM
SEC
UR
ITY
CA
SE IN
STR
UC
TIO
NS
Place the top shelf into the gondola at thedesired height. For example, if you want tobuild a 16” x 48” x 30” security case youwould place the top shelf about 30” fromthe bottom of the shelf bracket to theshelf or deck below (see below).
1
Ultra fixture pictured
+ 30”
R-0
7.11
.07
STR
-083
35-0
142
4
ULT
RA
& M
ILLE
NN
IUM
SEC
UR
ITY
CA
SE IN
STR
UC
TIO
NS
With the front of the door assemblyfacing away from you (door handles areaway from you) slide the support strapsinto the channel closest to you about 8”from each end.
2
With the front of the door assembly facingyou slide the gap filler in from one end tothe other so the gap filler is centered in theframe of the door assembly.
3
23 2
front
of
door
ass
embl
ysupport strap
front
of
door
ass
embl
y
support strapgap filler
R-0
7.11
.07
STR
-083
35-0
142
5
ULT
RA
& M
ILLE
NN
IUM
SEC
UR
ITY
CA
SE IN
STR
UC
TIO
NS
With the front of the door assemblyfacing you tip the top in slightly andinsert the gap filler behind the ticketmoulding, then slide the bottom of thedoor assembly in so it sits vertical onthe bottom shelf or deck.
4
Attach the support strap on the back-side of the door assembly to the outer–most hat on the top shelf using one (1)10-16 x 3/4” tek screw per support strap.
5
support strapgap filler
shelf bracket is transparent for clarity
4
5
5
hat
support strap
shelf bracket
R-0
7.11
.07
STR
-083
35-0
142
6
ULT
RA
& M
ILLE
NN
IUM
SEC
UR
ITY
CA
SE IN
STR
UC
TIO
NS
Attach the bottom of the door assemblyto the bottom shelf or deck with two (2)10 x 5/8” sheet metal screws, 1 per endend of the door assembly.
6
6
6
R-0
7.11
.07
STR
-083
35-0
142
7
ULT
RA
& M
ILLE
NN
IUM
SEC
UR
ITY
CA
SE IN
STR
UC
TIO
NS
Apply one piece of double face tape tothe inside of each end panel (end panelhooks face in). If the height of the endpanel is shorter then the length of tapetrim the tape to run between the twoholes in the end panel. If the end panelis taller then the length of tape cut thetape in half and apply each half one justbelow the top hole and the other justabove the bottom hole as pictured to theleft and below.
7
Hook the end panels into the slots onthe uprights so the hole in the end panelaligns with the keyed hole on the shelfas pictured to the left. When installedthe end panel should overlap the topshelf slightly as well as the bottom shelfor deck.
8
7
7
8
8
end panel
top shelf
R-0
7.11
.07
STR
-083
35-0
142
8
ULT
RA
& M
ILLE
NN
IUM
SEC
UR
ITY
CA
SE IN
STR
UC
TIO
NS
Secure the end panel to the top shelf usingone (1) 10-32 x 1/2” machine screw,washer and hex nut per end panel. Thewasher goes inside the security case withthe nut.
9
9
9
