Patterns for Slick database applications Jan Christopher Vogt, EPFL Slick Team #scalax.
1 Slick 1 2 Guide rail Sliding door fittings Slick 1€¦ · Set sliding door fittings Slick 1...
Transcript of 1 Slick 1 2 Guide rail Sliding door fittings Slick 1€¦ · Set sliding door fittings Slick 1...
Installation instructionsSliding door fittings Slick 1for wooden doors ( max. 1 3/4" thickness )
Complete-sets
Set Slick 1Artikel-No.
Ainch
Binch
CEach
Dinch
Emax. inch
Finch
Ginch
Hmax. inch
(H=E-F+1")
USU95-1800EF 70 7/8" 20 1/4" 4 29 1/2" – 35 7/16" 98 7/16" 1/4"–3/8" 2 3/8" 99 1/8"
USU95-2100EF 82 11/16" 24 1/8" 4 35 13/16" – 39 3/8" 98 7/16" 1/4"–3/8" 2 3/8" 99 1/8"
USU95-2300EF 90 9/16" 20 1/16" 5 39 3/4" – 44 1/16" 98 7/16" 1/4"–3/8" 2 3/8" 99 1/8"
USU95-2540EF 100" 22 7/16" 5 44 1/2" – 49 3/16" 98 7/16" 1/4"–3/8" 2 3/8" 99 1/8"
Comply with all general safety
regulations when installing the
sliding door fittings!
Installation to be completed by
qualified licensed contractor.
Be sure to tighten all screw
connections one week after starting
to use the sliding door fittings!
Never use scouring agents to clean
the sliding door fittings; rather use
commercially available stainless-
steel cleaners!Beyerle US L.L.C., ABP-Byerle it´s subsidiaries and agents are not
responsible or liable for damage or injury to any persons or property
due to improper installation of it´s products.
All liabilities reside solely with the installer.
Beyerle US L.L.C.1294 Logan Circle NW, Atlanta, GA 30318
Phone (404) 350-9738, Fax (404) 355-0166, www.beyerle-us.comRight to make technical changes reserved - Dimensions in inches - Version 11.2011x© by ABP-Beyerle GmbH
Attention
Screw on
Screw on
Screw on
Loosen/Tighten
Install
At right angle
Drill
Dowels
Adjust Set
Level
Perpendicular
Measure Mark
Visual inspection
Special-tool
2 people required
Measure
Clarify questions
See Instructions
Secure
Set Slick 1
Art. No.
USU95-1800EF
USU95-2100EF
USU95-2300EF
USU95-2540EF
1 2 2 4 1 1
1 2 2 4 1 1
1 2 2 5 1 1
1 2 2 5 1 1
2 3 4 5 6 7
Set /Each
US
U95
_MO
NT_
US
x
1
2
3
5
6
7
4
Set sliding door fittings Slick 1
Guide rail
Door stoppers
Wall fixtures
Special tool
Bottom guide(without screws and dowels, at construction site)
(without screws and dowels, at construction site)* not included in scope of delivery.
5/16"-18UNC
Trolley complete
*
1
SW 5
*
Bottom guide
glass doors 5/16" - 1/2"tempered safety glass
max. 220 lbs(100 kg)
Warning!Proper header or mounting
beam must be installed the fulllength of the sliding door railto provide adequale support
for sliding door system weightof door!
B5 1/8" 5 1/8"B B
wooden door max. 1 3/4“max 220 lbs
(100 kg)
Warning!Proper header or mounting
beam must be installed for the full length of the sliding door rail
to provide adequate supportbecause of the weight of the
sliding door system.
1 3/8"1 3/8"
1 3/8"
13/8"
1"
*
M8
Fig. 9
Fig. 1
Fig. 7
Right to make technical changes reserved - Dimensions in inches - Version 11-2011 x© by ABP-Beyerle GmbH
Installation instructions Sliding door fittings Slick 1 for wooden doors ( max. 1 3/4" thickness )
Fig. 13
Fig. 2
Fig. 14
Fig. 20
Fig. 3 Fig. 4
Fig. 10
Fig. 5
Fig. 11
Fig. 6
Fig. 18
max.30 mm
Installation to becompleted by
contractor
lbsFig. 4, 5, 6 = 7
max.220 lbs(100 kg) max. 1 3/4"
5/16" - 18UNC
2"
2"
Fig. 3-12
5/16"-18UNC
M 4,5
Fig. 8
130
25
GG
E
2
11
251/8"
1"B
BB
3
1
2± 1/ 8"
Fig. 21
Fig. 12
Fig. 14-23Fig. 15 Fig. 16 Fig. 17
1 23
Fig. 22 Fig. 23Fig. 19
2
1
2
1
2
Planning guideSliding door fittings Slick 1for wooden doors ( max. 1 3/4" thickness )
Complete-sets
Set Slick 1Artikel-No.
Ainch
Binch
CEach
Dinch
Emax. inch
Finch
Ginch
Hmax. inch
(H=E-F+1")
USU95-1800EF 70 7/8" 20 1/4" 4 29 1/2" – 35 7/16" 98 7/16" 1/4"–3/8" 2 3/8" 99 1/8"
USU95-2100EF 82 11/16" 24 1/8" 4 35 13/16" – 39 3/8" 98 7/16" 1/4"–3/8" 2 3/8" 99 1/8"
USU95-2300EF 90 9/16" 20 1/16" 5 39 3/4" – 44 1/16" 98 7/16" 1/4"–3/8" 2 3/8" 99 1/8"
USU95-2540EF 100" 22 7/16" 5 44 1/2" – 49 3/16" 98 7/16" 1/4"–3/8" 2 3/8" 99 1/8"
Right to make technical changes reserved - Dimensions in inches - Version 11.2011x - Page 1 of 6© by ABP-Beyerle GmbH
Bottom guide
glass doors 5/16" - 1/2"tempered safety glass
max. 220 lbs(100 kg)
B5 1/8" 5 1/8"B B
Warning!Proper header or mounting
beam must be installed for the full length of the sliding door rail
to provide adequate supportbecause of the weight of the
sliding door system.
wooden door max. 1 3/4“max 220 lbs
(100 kg)
1 3/8"1 3/8"1 3/8"
Sliding door fittings Slick 1for wooden doors ( max. 1 3/4" thickness ) - 1 door
Calculation for guide-rail length A for 1 door
Manufacturing dimensions (special model)
inchesA B C D D1 G L M N
1 2 2
Emax. 98 7/16"
Hmax. 99 1/8"(H = E - F + Y)
lbsload bearingcapacity of
the guide railJ
F1/4"-3/8"
2 3/8"
Each Eachinches
Make door handle clearance so that fingers do not get pinched when the door is used! See page 5.
Right to make technical changes reserved - Dimensions in inches - Version 11.2011x - Page 2 of 6© by ABP Beyerle GmbH
Overhang Z (1")
(Guide-rail)
Guide-rail lenght A
Overhang Z + Passage width D + Door width D1 - Door handle clearance X = Guide-rail length A
Passage width D
Door handle clearance X
Door width D1
A = Guide-rail lengthB = Drill hole clearanceC = Wall fixtureD = Passage widthD1 = Door widthE = Passage heightF = Door - floor clearanceG = Fastening clearanceH = Door heightJ = Load-bearing capacity of the guide railL = Bottom guideM = Door stopperN = TrolleyX = Door knob clearanceY = Door height overhangZ = Guide-rail overhang
( ) = recomended!
1 3/8"
Bottom guide
wooden door max. 1 3/4"max. 220 lbs
(100 kg)
Warning!Proper header or mounting
beam must be installed for the full length of the sliding door rail
to provide adequate supportbecause of the weight of the
sliding door system.
B
D
L
B
J
B
A max. 118 1/8"
max. 20"
Emax.
98 7/16"H
max. 99 1/18"
Z
X
max. 20" max. 20"
5 1/8" 5 1/8"
D1 = D + (2")
M
N N
G (2 3/8")Y 1"
1 3/8"
glass doors 5/16" - 1/2"tempered safety glass
max. 220 lbs(100 kg)
Warning!Proper header or mounting
beam must be installed the fulllength of the sliding door railto provide adequale support
for sliding door system weightof door!
B5 1/8" 5 1/8"B B
1 3/8"
"
1 DD
5 1/8BBB"5 1/8
C C C C C C C C
1
Warning!Proper header or mounting
beam must be installed for the full length of the sliding door rail
to provide adequate supportbecause of the weight of the
sliding door system.
max. 20"
B1 B1 B1 B2 B2max. 20" max. 20" max. 20" max. 20" max. 20"
D1 D2
N (Door stopper )
A max. 118 1/8" A max. 118 1/8"
G (2 3/8")Y 1"
K
N
L
J
X X
M
glass doors 5/16" -1/2"tempered safety glass
max.220 lbs(100 kg)
glass doors 5/16" -1/2"tempered safety glass
max.220 lbs(100 kg)
E
D max. 98 7/16"D max. 98 7/16
wooden door max. 1 3/4"max.220 lbs
(100 kg)
wooden door max. 1 3/4"max.220 lbs
(100 kg)
(3/16")L
B2
Sliding door fittings Slick 1for wooden doors ( max. 1 3/4" thickness ) - 2 doors
Calculation for total guide-rail length A for 2 doors
Manufacturing dimensions (special model)
inches
A B1 B2 C D D1 D2 G K L M N
1 2 4 4
Emax.
98 7/16"
Hmax. 99 1/8"(H = E - F + Y)
lbsload bearingcapacity of
the guide railJ
F1/4"-3/8"
2 3/8"
EachEachinches
Make door handle clearance so that fingers do not get pinched when the door is used! See page 5.
Right to make technical changes reserved - Dimensions in inches - Version 11.2011x - Page 3 of 6© by ABP Beyerle GmbH
Total guide-rail length A
Door width D1 - Door handle clearance X + Passage width D + Door width D2 - Door handle clearance X = Total guide-rail length A
Passage width D
Door handle clearance X Door handle clearance X
Door width left D1 Door width right D2
A = Guide-rail lengthB = Drill hole clearanceC = Wall fixtureD = Passage widthD1 = Door widthE = Passage heightF = Door - floor clearanceG = Fastening clearanceH = Door heightJ = Load-bearing capacity of the guide railK = CouplingL = Bottom guideM = Door stopperN = TrolleyX = Door knob clearanceY = Door height overhangZ = Guide-rail overhang
( ) = recomended!
5/16“
3/16" 3/4"
*
"3/4
Sliding door fittings Slick 1for wooden doors ( max. 1 3/4" thickness ) - Wall fixture
Standard installation Installation with baseboards and trim
Right to make technical changes reserved - Dimensions in inches - Version 11.2011x - Page 4 of 6© by ABP Beyerle GmbH
*
**
USO226-33EF 1 5/16"
Art.-No. inches
Sliding door fittings Slick 1for wooden doors ( max. 1 3/4" ) - Preparation of door
Right to make technical changes reserved - Dimensions in inches - Version 11.2011x - Page 5 of 6© by ABP Beyerle GmbH
Make door handle clearance so that fingers do not getpinched when the door is used!
ø 17/32“
Sliding door fittings Slick 1for wooden doors ( 1 3/4" thickness )Required system parts
Please refer to the catalouge for article no’s and models!
Right to make technical changes reserved - Dimensions in inches - Version 11.2011x - Page 6 of 6© by ABP-Beyerle GmbH
A
A1
M
C
6
K
L
N
Guide rail ø 1 "
Guide rail ø 1 " for guide rail couplings
Door stoppers
Wall fixtures
Special tool
Guide rail cuppeling
Bottom guide(without screws and dowels, at construction site)
(without screws and dowels, at construction site)* not included in scope of delivery.
5/16"-18UNC
Trolley complete
*
SW 5
*